Search Results

Search found 202 results on 9 pages for 'canon pixma'.

Page 1/9 | 1 2 3 4 5 6 7 8 9  | Next Page >

• Canon MX870 printer only shows "Processing" on the status LCD

  - by Nick

  I had my Canon MX870 installed perfectly fine in 11.10, but since upgrading to 12.04, it no longer works. The printer is recognized in print settings and when I attempt to print a test page, the printer LCD displays a "Processing" message, but then it disappears and nothing happens. Here are my logs (note that printing did not succeed despite the access logs showing success): # /var/log/cups/access_log localhost - - [22/May/2012:12:29:35 -0400] "POST /printers/Canon-MX870 HTTP/1.1" 200 412 Print-Job successful-ok - # /var/log/cups/error_log W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-Gray..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-RGB..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateDevice: org.freedesktop.ColorManager.AlreadyExists:device id 'cups-Canon-MX870' already exists W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-Gray..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-RGB..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateDevice: org.freedesktop.ColorManager.AlreadyExists:device id 'cups-Canon-MX870' already exists W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-Gray..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-RGB..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateDevice: org.freedesktop.ColorManager.AlreadyExists:device id 'cups-Canon-MX870' already exists W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-Gray..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateProfile: org.freedesktop.ColorManager.AlreadyExists:profile id 'Canon-MX870-RGB..' already exists W [22/May/2012:12:25:51 -0400] failed to CreateDevice: org.freedesktop.ColorManager.AlreadyExists:device id 'cups-Canon-MX870' already exists

  Read the article

• Can't print on my brand new Canon Pixma MP495

  - by Jean Ludovic Vandal

  I just purchased a Canon Pixma MP495. It was working perfect, except for the scanner. It won't install the driver for the scanner. Anyway, I was printing using the new printer. After a while, it started saying that the printing job was sent to the printer and then that the print job was completed. But, nothing came out of the printer. I uninstalled the driver and installed it over again. Nothing. Can somebody help me out. Can't work without a printer. Thanks in advance.

  Read the article

• How to install Canon MP610 printer on Ubuntu 12.04 x64

  - by Arkadius

  I installed Ubuntu 12.04 x64. Orginal Canon drivers are only for 32-bit version. How can I install this printer in 64-bit version ? Arkadius HERE IS SOLUTION I looked for solution some time and finally found it. First I try to do it by adding repository like it is written here: http://www.iheartubuntu.com/2012/02/install-canon-printer-for-ubuntu-linux.html BUT it did NOT work. Printer was installed but every print JOB goes somewhere ( probably to /dev/null :) ) Also installing sudo apt-get install ia32-libs did NOT worked (it was already installed) Finally I found solution. NOTE I did NOT use orginal Canon drivers for 32-bit. I also removed drivers from repository: ppa:michael-gruz/canon I found solution almost at the end of this thread: http://ubuntuforums.org/showthread.php?t=1967725&page=10 Most important hint was found in Response #97 "Do NOT install any PPA" I did as follows: Removed all copies of my printer Removed Canon drivers from repository ppa:michael-gruz/canon sudo apt-get remove cnijfilter* Added new repository and installed CUPS for Canon: sudo apt-add-repository ppa:robbiew/cups-bjnp sudo apt-get update sudo apt-get install cups-bjnp Installed Gutenprint: sudo apt-get install printer-driver-gutenprint Restarted CUPS: sudo restart cups Add myself to group lp: sudo usermod -G lp -a your_user_name Added printer usings steps from link above: Don't install any PPA for the drivers. Click the Cog up in the right-hand corner and select Printers. Turn on the printer and make sure it is connected. When the Printers windows appears, click +Add and wait a few minutes. Your printer should appear within the configuration wizard. Mine did and its an Canon MX330. Click the defaults and continue on. Cups should identify your printer. I saw a few other models in the list. I was able to successfully print a test page afterwards. I hope this will also help someone else. Arkadius .

  Read the article

• Why does my Canon printer print document pages at ~25% size?

  - by Erlend Alvestad

  I'm using a Canon PIXMA MP250, and I'm running 12.04 LTS. The printer's been working fine for the couple of months I've been a Linux user. That is, until today. I just printed a 1-page ODT document from LibreOffice. Instead of filling the sheet, the document occupies only a little less than 25% of the paper, in the top left corner, and the text has also shrunk to something like 5pt. I looked at the paper format settings for the document and printer, which were set to "letter". I changed these to "A4", hoping that would solve the issue. There was no change, however. I tried printing a different document in LibreOffice and got the same result. I tried exporting the original document to PDF and printing it through Document Viewer. Same result. I then printed a web page from Google Chrome. No formatting problems there. In all cases the print preview looks fine.

  Read the article

• Canon LIDE 30 scanner with Windows 7 x64

  - by marc_s

  Has anyone gotten any of those older LIDE scanners (models 20, 30, 35 etc.) to work on Win7 x64?? I've tried several things, like grabbing the LIDE 60 driver for Vista64, but nothing has worked so far.... Any ideas? Doesn't look like Canon wants to support its "more-than-six-months-old" own hardware.... disappointing, really.

  Read the article

• How can I scan from Canon PIXMA MX700 without disabling OS X firewall?

  - by Justin Love

  I have a Canon PIXMA MX700 connected by ethernet. When I first bought it I was using OS X 10.4, and scanner-initiated scanning worked fine. After upgrading to 10.6, neither scanner-initiated or scanning from MP Navigator EX works with the firewall enabled. The firewall lists exceptions for three applications: Canon IJ Network Scan Utility.app Canon IJ Network Scanner Selector.app MP Navigator EX 1.0.app I get no further blocked warnings, and /var/log/appfirewall.log lists nothing for today (my latest attempt to use it).

  Read the article

• Will the Canon Pixma MX882 Wireless Multifunction Printer allow you to keep printing once one ink cartridge has run out?

  - by braveterry

  My wife's Epson Workforce 600 has died, and I'm thinking of replacing it with a Canon Pixma MX882 printer/scanner/copier/fax. One of the most annoying things about the Epson is that once it has decided that one of the ink cartridges is empty, it will not let you print anything until the empty cartridge is replaced. I have a Canon IP1800 that will let you print until a cartridge actually runs out of ink, and even when a cartridge is depleted, I can continue to print using the other colors. (The driver allows you to print using only the color cartridges or using only the black cartridge.) Questions: Will the Canon Pixma MX882 allow me to print until the ink runs out or will it declare the cartridge empty while ink is still left? Will the Canon Pixma MX882 allow me to keep printing even after one of the cartridges has been used up?

  Read the article

• How can I scan from Canon PIXMA MX700 without disabling OS X firewall?

  - by Justin Love

  I have a Canon PIXMA MX700 connected by ethernet. When I first bought it I was using OS X 10.4, and scanner-initiated scanning worked fine. After upgrading to 10.6, neither scanner-initiated or scanning from MP Navigator EX works with the firewall enabled. The firewall lists exceptions for three applications: Canon IJ Network Scan Utility.app Canon IJ Network Scanner Selector.app MP Navigator EX 1.0.app I get no further blocked warnings, and /var/log/appfirewall.log lists nothing for today (my latest attempt to use it).

  Read the article

• Installing Canon LBP6000 in Ubuntu 12.04

  - by MMA

  This is really frustrating. I am trying to install LBP6000 in Ubuntu 12.04 without any success. (Well, I had success about a week back when I first bought the printer and finally printed pages after a struggle of several hours. Then today it suddenly stopped working and I uninstalled everything and started from scratch. Now, I seem to have lost the way.) My steps Downloaded the latest Canon driver from Canon site. File Linux_CAPT_PrinterDriver_V240_uk_EN.tar.gz Got the radu script (I am allowed only two hyperlinks, so can not put the link here. You can Google radu Canon) Changed the /etc/modprobe.d/blacklist-cups-usblp.conf file as instructed in, Official Documentation. (See the section Ubuntu 12.04 Install). Now this file looks like, # cups talks to the raw USB devices, so we need to blacklist usblp to avoid # grabbing them # blacklist usblp Rebooted my machine Changed the port in radu script to 59787 as instructed in the link at step 3. (Again see the section Ubuntu 12.04 Install, or see the comment at How to Install Canon LBP Printers in Ubuntu. Also put the latest deb files from step 1 in the appropriate directory of this script. Ran the radu script. A printer, LBP6000 got added. Not two printers, one to be disabled, as appeared in the message on the terminal after running the script. sudo /etc/init.d/ccpd status shows, Canon Printer Daemon for CUPS: ccpd: 3142 3139 Results The printer does not print. Printer state (from System Setting-Printing, or at cups http interface localhost:631/printers/LBP6000) goes from Idle to Processing, a job appears in print queue, and then the job disappears and the printer state goes back to Idle. The actual printer does not even blink. Diagnostics (got help from the link in step 3, Troubleshooting) captstatusui -P LBP6000 shows communication error lsmod | grep usblp did not show anything. After running, sudo modprobe usblp, shows usblp 17885 0 However, ls -l /dev/usb/lp0 gives, ls: cannot access /dev/usb/lp0: No such file or directory /var/ccpd did not exist, created, sudo mkdir /var/ccpd sudo mkfifo /var/ccpd/fifo0 sudo chown -R lp:lp /var/ccpd Any suggestion will be appreciated. Do not know what to do.

  Read the article

• Diagnosing the problem when Canon printer fails to print under Ubuntu

  - by MMA

  I understand that the issue of Canon printer under Linux has a number of posts. Actually one of these, was started by me. After inputs from others I have successfully printed using Canon LBP6000 from my Ubuntu machine for around a year. If it failed to print, restarting the daemon using this homemade script coaxed the printer to print. #!/bin/bash pkill -9 -x ccpd pkill -9 -x captmoncnabc /etc/init.d/ccpd start /etc/init.d/ccpd status Recently, I am not successful any more, or successful on a limited and sporadic basis. Sometimes it prints when turned on after logging in, sometimes when the driver is reinstalled. I keep on trying the random steps (call abracadabras) until I get success. Again, not always success comes. I frustrate on for hours only to get single page printed. I loose precious time on the issue of printing. I have read and read all the documents available over the Internet. However, if you please notice, none of the guides, articles, tutorials (these are too many to list here) seem to be dealing with diagnosing the problem when it fails to print. They tell you where to find the drivers, how to install them, or which script to run to make the installation process automatic. Yes, some of the articles or comments suggest a step to try, without any systematic order. But these fail to suggest a step based on symptoms, mostly. This morning, my Canon LBP6000 failed to print. After sometime, there was a message for system error, details of which was found to be something like this. When I search for this error (c3pldrv crashed with SIGSEGV in write ()), I find a number of articles including this one. None of these are actually helpful. Mostly, these are 'me too', 'tell me if you find anything'. Running captstatusui -P LBP6000 produced this, Yes, the printer is connected and actually turned on. I believe that there a number of frustrated Canon printer users out there like me. But there is not a step by step definitive guide to systematically diagnose a non-printing printer. Do you think that you can provide your diagnosing inputs so that a systematic document can be built? May be we will want the Ubuntu users to stay away from Canon printers. But as I believe, as a Linux user for more than fifteen years, such a scenario is not acceptable any more. May be this was acceptable in the infancy days of Linux, but not today. I am using Ubuntu 12.04, by the way, I prefer LTS versions.

  Read the article

• Canon Pixma MP150 printer stops before the job is done

  - by aserwin

  I have a Canon Pixma MP150. It's old but it still works well. The problem is that since I have been running Ubuntu 12.04 the printer exhibits odd behavior. Usually right at the end of a job, it will stop. The printing is done, but the printer is still "working" and it won't release the paper. If I pull it out and test the printer, it will start over and print the same job. Once I just let it be and about an hour or so later it finished with no problems. My question is, could the be an issue with the printer (it is old) or is it the drivers in Ubuntu? Any advice (or suggestions on debugging) would be greatly appreciated as I print a lot and don't really want to buy a new printer.

  Read the article

• Trying to install Canon iP7250 printer

  - by Chris Burmajster

  I'm trying to install my Canon iP7250 printer on a fresh install of 13:10 64bit. Last time I installed it successfully via http://handytutorial.com/install-canon-printer-driver-for-ubuntu-13-04-12-10-12-04 which entailed adding a repository via the terminal and then updating it. I then opened Synaptic and searched for my printer model and Synaptic then installed everything. This time round I added the repositories but the update failed with the following error: Failed to fetch http://ppa.launchpad.net/michael-gru...amd64/Packages 404 Not Found Failed to fetch http://ppa.launchpad.net/michael-gru...-i386/Packages 404 Not Found Some index files failed to download. They have been ignored, or old ones used instead. An internet search failed to find another way of installing this printer so I'm stuck. My laptop also runs 64 bit 13:10 and the printer works, as I installed it months ago. Is there any way I can take something off that to use on this new machine? Thank you all in advance P.S. I have just found and downloaded the official Canon driver from the Canon website and extracted it, but I don't know how to install it.

  Read the article

• Canon Mx772 printer recognized, drivers loaded...but all print jobs "Held"

  - by user212169

  BRAND NEW to Ubuntu but loving it so far. I have a Canon MX772 wireless printing running on my network and am able to print fine from a PC and Mac. Using the printers IP, Ubuntu was able to find it and I accepted all of the "recommended" items (it found a Canon MX770 driver). Everything seems to load fine...but the test page does not print, nor does any print commands make it to the printer. If I open the print dialogue jobs are shown as "held" and when I look at the jobs attributes, I see "Job printer state message=cannot specify model number" and then a few lines down "job state reasons=aborted by system". If I try to "resume" it immediately goes back to "held". I can successfully ping the IP of the printer. Would be very appreciative of other ideas...printing is the last check in the box before I am all set up. Thanks!

  Read the article

• How to install downloaded Canon ScanGear

  - by GreenSee

  I have newly installed Ubuntu 12.04. I have Canon MG6360 printer/scanner. I have successfully installed printer drivers and can print okay. Have downloaded MG6300 series ScanGear MP Ver. 2.00 for Linux (deb) from Canon but don't know how to install this from terminal. I apologise for having to ask such a basic question! Thanks. Later...I have extracted the files. Question appears: Do I want to run install.sh? I click 'run in terminal', and enter password. I don't know if it installed and don't know how to check. Scanner does not work or 'see' the PC. Any advice would be greatly appreciated.

  Read the article

• Canon MP280 All in One prints but scanner not recognized

  - by Chris

  I recently installed Ubuntu 12.04 LTS after not using any Linux distro for several years. My Canon MP280 worked perfectly as far as printing goes and I was even able to set it up on a Samba share and print from a Windows 7 machine. However when I open Simple Scan it does not detect a scanner. I did find some instructions online but the scanner is still not recognized in Simple Scan even after installing a couple .deb packages from the Canon site. I also couldn't seem to find the ScanGear package after installing those .deb packages as well but I haven't had a chance to delve fully into it. Thanks for your time!

  Read the article

• Trying to install Canon LBP7750Cdn driver on Ubuntu 12.04

  - by Gideon

  I'n new to Ubuntu/Linux and had significant difficulties while attempting to configure my printer to work. The automatic driver pairing wizard which Ubuntu uses to identify and install the appropriate drivers did not find my printer's driver. I managed to get it to print when I manually select the generic configuration and checked the PCL6 configuration. However, the printer driver wizard does provide a list of Canon printers and actually do specify my printer as LBP7750C (minus the "dn" at the end, I'm assuming its because duplex ability and networking is not present on all the models - I'm not sure if this could be the source of the problem), but in selecting this option and trying to print I receive this message: Idle - /usr/lib/cups/filter/foomatic-rip failed I searched for this similar problem which other users might have encountered, but while there where plenty of such cases, they all had different resolutions and were all related to HP printers. Canon actually do provide a driver for my printer, but it comes with no installation instructions unless you consider yourself an experienced CUPS guru. Seriously. If anyone can help me solve this foomatic-rip failed problem I'd be really grateful - and I'm sure many other folks too. [BTW, can't Canonical fix this type of thing for the next Ubuntu release? - I't seems like a small problem but it causes many problems and countles hours of production time loss.] Thanks in advance.

  Read the article

• Printer sharing problem (win7 / WinXP): Canon pixma USB printer

  - by Rabarberski

  For a friend, I am trying to share a USB Canon pixma ip3000 printer between two computers in his home network. But I can't get it to work due tot a Canon driver problem. The printer is connected to the Windows 7 (64 bit) computer, and we would like to be able to print from a Windows XP computer. 'Normally' it should be no problem to use Windows printer sharing, however, because one machine is 32-bit and the other is 64-bit, installing an extra driver is required. T he driver provided by canon (here) is described as a 'Canon Inkjet Printer Driver Add-On Module'. The problem is that the .inf file contained in the .exe file isn't accepted as a driver when prompted by the Printer Sharing Wizard, I suspect because it is an add-on driver (whatever that may be). I've connected and installed the printer locally on the XP machine first (which works), so that the XP machine would already know the driver when using it as a network printer, but that doesn't work; the wizard still wants a driver file. Anybody suggestions how to get this working? Maybe there is some sort of generic driver (would be OK even with limited functionality)?

  Read the article

• Canon MP495 Scanner not working

  - by Andrew

  Running 12.04, installed and updated latest drivers for MP495 but nothing stil. latest drivers provided here: https://code.launchpad.net/~michael-gruz/+archive/canon-trunk/+packages Followed this guide to the letter: http://ubuntuforums.org/showthread.php?t=1602839&page=11 Xsane and simple scan do not work. I have tried various other programs and have nothing... People are saying it works well with 11.10, so I don't know what the deal is with 12.04. Any help would be greatly appreciated as I need this printer for my out-of-home business, and I really don't want to switch back windows just for a freaking scanner to function. Why don't these companies realise ubuntu users need to print things too?!

  Read the article

• How to make LBP-1120 Canon printer work?

  - by cipricus

  Initially this question was limited to 11.10. Now I am in (Lubuntu) 12.10. (On the changes in the question see this meta question). Considering 11.10 I have tried different (or not so different) approaches - that also other users commented here. My main references were: the ubuntu official documentation website on the LBP Canon driver package, this Unixmen solution which partly refers to Radu Cotescu script that aims at providing a near-automated install, and an updated by Unixmen version of that very script (download here). None worked for me.

  Read the article

• Trouble using Canon MG 2440 printer in UBUNTU 14

  - by user264795

  I connected usb serial cable from printer to computer. The drivers has been installed automatically. I printed the test page - it was printed. I tryed to print an image - it stays with status - processing... and dont work. Test page also cant be printed. What a problem? I dont know exactly, but I think I use "CUPS" manager and drivers... now status Waiting for printer to become available. And do not print.

  Read the article

• Canon LiDE 600F FAU on Snow Leopard?

  - by jdmuys

  Hello, I have been able to use my Canon LiDE 600F scanner under Snow Leopard to scan paper sheet, after installing Canon's latest driver software. However, I cannot find a way to make the FAU (Film Adaptor Unit) to work: Canon's software want to calibrate it first and gives an error message "Calibration cannot be performed. Pull out the film. 182.0.0". (of course there is no film). Hamrick's VueScan doesn't seem to support the FAU Apple's Image Capture doesn't propose a film option either Did I miss something? Did somebody manage to scan film (positive or negative) using the LiDE 600F under Snow Leopard? Many thanks

  Read the article

• Canon LiDE 600F FAU on Snow Leopard?

  - by jdmuys

  I have been able to use my Canon LiDE 600F scanner under Snow Leopard to scan paper sheet, after installing Canon's latest driver software. However, I cannot find a way to make the FAU (Film Adaptor Unit) to work: Canon's software want to calibrate it first and gives an error message "Calibration cannot be performed. Pull out the film. 182.0.0". (of course there is no film). Hamrick's VueScan doesn't seem to support the FAU Apple's Image Capture doesn't propose a film option either Did I miss something? Did somebody manage to scan film (positive or negative) using the LiDE 600F under Snow Leopard? Many thanks

  Read the article

• Printer features don't work when printing to Canon Printers ir5185 and ir7095 in Snow Leopard

  - by Ken

  Recently updated to iMac running Snow Leopard. Connected Canon printers ir7095 and ir5185 via ethernet and downloaded latest drivers from Canon website. Can print to both from InDesign CS3, however, when I select printer features such as heavy paper and printing to stack bypass, it prints but just defaults to plain paper in drawer 1. Also, when printing to ir7095, 0001 prints five times on sheet in background. Is there any way to get the printer features that are available to work?

  Read the article

• Move files from Mac to Canon PowerShot digital camera

  - by Frost Shadow

  When I plug my Canon PowerShot digital camera into Snow Leopard, it automatically opens iPhoto and asks to import the pictures, but does not mount the camera on the desktop (from what I read, it's a Canon feature to prevent people from screwing up the file system on the memory card, or something). Is there a way I can move photos I've already imported back on to the camera? I can't seem to figure out how to move stuff from Snow Leopard to the camera using iPhoto, and since it doesn't mount....

  Read the article

• How do I get a Canon LBP 2900 printer working?

  - by elektron

  i am unable to set up my canon lbp2900 printer on ubuntu12.04 64 bit i aliened the 64 bit rpm drivers and then installed the drivers (version 2.40) and followed the procedure in the canon guide ( however i changed fifo path to //localhost:59787 (somebody suggested) instead of 59687 (as suggested by canon guide) ) intially i got the message pstocapt failed .. the drivers had put the pstocapt and backend/ccp in the lib64 directory instead of the lib directory ... i copied that to the aproprite directory under lib but still i get the error "ccp send_data error exit " i also tried with fifo path //localhost:59687 i also tried the Radu script but the drivers the script uses are version 1.90 and has conflicting packages

  Read the article

1 2 3 4 5 6 7 8 9  | Next Page >