Search Results

Search found 32 results on 2 pages for 'edimax'.

Page 1/2 | 1 2  | Next Page >

• Edimax wireless router is not providing DNS services correctly

  - by Nathan Fellman

  I have an Edimax router that is set up to connect to the internet via L2TP on cable, and on the LAN side it's set up as a DHCP server. The DHCP server gives correct IP addresses, but it sets itself up as the DNS server. However, it doesn't provide the DNS service. I am sure that it's a problem with the router, because I have two computers on the network with the same problem. I see that on the WAN side it gets correct DNS addresses from the ISP, so I'd expect the router to either pass these addresses through to the DHCP clients, or to serve the DNS requests itself by forwarding them to the ISP's DNS. However, it apparently does neither, and there is no DNS. I switched from ADSL to cable last week. On ADSL it connected using PPPoE, and the DNS worked fine. What can be the problem here?

  Read the article

• Internet access using Edimax BR-6204WG as NIC

  - by Mat Richardson

  My internet access at home is provided by Virgin Media via their superhub. I have a laptop with no NIC - however I do have a spare wireless router, the Edimax BR-6204WG, which I have been led to believe can be used to bridge wireless connections. Only problem is, I'm not sure how to go about doing this. The manual for the device is here:- http://www.edimax.co.uk/images/Image/manual/Wireless/BR-6204Wg/BR-6204Wg_Manual.pdf Basically, I want to be able to connect the Edimax wireless router to my laptop using ethernet cable and to use it to pick up the wireless connection from my Virgin superhub. I've managed to get so far in some ways, but then I'm stuck.

  Read the article

• Setting up Edimax EW-7206APg as Universal Repeater

  - by Ondra Žižka

  Hi, I've troubles setting up Edimax EW-7206APg as a Universal Repeater. I've read few manuals, but they are unclear on certain points. I've managed the repeater to get to a state when it's in a "connected" state. I've set the same WPA passphrase as the router has because I haven't seen any other place to set it at. These are my settings: System Uptime 0day:1h:33m:11s Hardware Version Rev. A Runtime Code Version 1.32 Wireless Configuration Mode Universal Repeater ESSID edimax Channel Number 6 Security WPA-shared key BSSID 00:c0:9f:40:bd:38 Associated Clients 0 Wireless Repeater Interface Configuration ESSID Dusan Security WPA BSSID 00:4f:62:23:8f:7e State Connected LAN Configuration IP Address 192.168.0.10 Subnet Mask 255.255.255.0 Default Gateway 192.168.0.1 MAC Address 00:c0:9f:40:bd:37 This is ipconfig /all: Prípona DNS podle pripojení . . . : riomail.cz Popis . . . . . . . . . . . . . . : Intel(R) PRO/Wireless 2200BG Network Connection Fyzická Adresa. . . . . . . . . . : 00-0E-35-3D-77-68 Protokol DHCP povolen . . . . . . : Ano Automatická konfigurace povolena : Ano Adresa IP . . . . . . . . . . . . : 192.168.0.5 Maska podsíte . . . . . . . . . . : 255.255.255.0 Výchozí brána . . . . . . . . . . : 192.168.0.1 Server DHCP . . . . . . . . . . . : 192.168.0.1 Servery DNS . . . . . . . . . . . : 94.74.192.252 94.74.192.244 I can ping the repeater, I can ping the root AP, but not a DNS server or any other IP beyond the root AP. Anyone has an idea what's wrong? Thanks, Ondra

  Read the article

• No internet connection using Edimax routers

  - by idan315

  I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. I am really lost on how to approach this problem. Possible leads: when I view the network information, I see that my computer is connected to 'Multiple Networks'. One of those is "Network 4" (probably my router), and the other is Unidentified network. I don't know how to make the "Unidentified Network" disappear, or why is it even there in the first place. When I try using "ipconfig", I have two default gateway IPs. The first is 0.0.0.0, and the second is the IP of my router (192.168.2.1). The first router was Edimax BR-6204Wg. The second one I've tried connecting is BR-6424n. Any ideas?

  Read the article

• Windows 7 Intermittent Connection Issues (Continuously "identifying")

  - by andrewktmeikle

  I have an issue solely with my desktop windows 7 machine on my network (the network has multiple different devices, on the same and different operating systems) and the issue is that irregularly, although sometimes frequently, I briefly get disconnected from the internet (briefly is for around 5-10 seconds). However, I never loose the bars on the wifi thing, eg I don't get the yellow triangle, but it goes to the identifying stage and then reconnects. The reason I noticed the problem was when I was streaming music it would stop and I would refresh the page and it would start working again ( turned out it was because it took that amount of time to get connected again). So my question is, what would cause the intermittent issues and start the "identifying" process again. I don't think its my router, because no one else is having problems, so the other option is that its a problem specifically with my machine. I'm connecting to a Netgear DG834GT router, and I'm using a Edimax Wireless-N150 USB Adapter. Anyone have any ideas?

  Read the article

• How do I get a 300Mbps connection over 802.11n?

  - by Daniel Schaffer

  I just bought a new wireless setup, consisting of a Cisco E2000 router, Edimax 7718un USB adapter for my laptop and an Edimax 7728in PCI adapter for my HTPC (which isn't in a location I can run cat5 to). I have to stay in the 2.4GHz band because I have an iPhone and a Wii that will need to connect. I'm aware that 11g devices will drop speeds for 11n devices, but they aren't connected yet. The fastest connection I've been able to get, with the router within 5 feet of either the laptop or HTPC is 144Mbps. The router has settings for "20MHz" and "Auto (20 MHz or 40Mhz) channel width, which I've set to the "Auto" setting. I haven't been able to find anything similar for either of the Edimax adapters. This is the first I've dealt with 11n, so I'm not even sure what else could be causing a problem. How do I get up to 300Mbps, or at least a fair bit closer?

  Read the article

• Firewall software that can block access to certain applications on certain internet connections

  - by webmasters

  I have two internet connections, a LAN and a 3G modem on a Windows 7 machine. The LAN is connected to a Edimax router which is conneted to the ISP (with their own modem). Now, the Edimax router is set to auto assign IP adresses in the range: 168.192.2.100 and 192.168.2.200 I wanted to block internet explorer to access the LAN. I entered my AVG firewall, selected iexplorer and added a "block" rule which blocked all ports, TCP and UDP protocols for the above IP range. The problem is it did not work, not matter what rules I have tried. Can you recommend a firewall that can easily accomplish this? Ty

  Read the article

• Why is Windows 7 so slow to log-on when my Wireless USB dongle is plugged in?

  - by Sam

  I'm using an Edimax Wireless USB dongle (model EW-7711UTN) on Windows 7 64-bit. The dongle works brilliantly (it was truly plug-and-play) except for one thing. I've noticed that if the dongle is plugged in whilst I'm logging on to Windows it introduces a massive delay - after I type in my password and hit enter, Windows shows the "Welcome" screen, then the screen goes black for 2 minutes or so (with just the cursor showing) before finally displaying my desktop. If I unplug the dongle before I enter my password, Windows goes straight to my desktop. Even though the dongle didn't appear to need drivers for Windows 7, I did try downloading the latest ones from the Edimax website, but that made no difference.

  Read the article

• My wireless network slows down every 7.5 minutes when my desktop is switched on

  - by Dog Ears

  My network has lag spikes lasting for a few seconds every 7.5 mins. The spikes also effect any other computer connected connected to my wirless router at the time. My wife has to connect her laptop via a cable to prevent the lag causing problems when she's VPNing into her work. If I switch my PC off the problem goes away! I've got an Edimax 7728ln 802.11n wireless card and Speedtouch 585v7 (I'm with Be) I've Tried... Updated the drivers from Edimax website: 2.0.3.0 (it does say 3.0.2.0 in devices properties though) WLAN Optimizer doesn't seem to be helping What can I do?

  Read the article

• Ralink RT3060 wireless device configuration on ubuntu 12.04

  - by Stephan

  concerning How do I get a Ralink RT3060 wireless card working? I'm running Ubuntu 12.04 with a 'LWPX07 Edimax EW-7711In 150M 1T1R WL PCI Card' which has a rt3060 chip. Out of the box the card is recognized as rt2800sta. I tried solution one, that didn't work. Still the card connects to the wireless network, but it seems to slow to load any pages. Then I tried solution 2, but then the network-manager doesn't see any wireless device. $ iwconfig lo no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. $ lsmod Module Size Used by rt3562sta 882296 0 $ lspci -v 05:02.0 Network controller: Ralink corp. RT3060 Wireless 802.11n 1T/1R Subsystem: Edimax Computer Co. Device 7711 Flags: bus master, slow devsel, latency 64, IRQ 23 Memory at ff9f0000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: rt2860 Kernel modules: rt3562sta, rt2800pci Am I missing a configuration step? How do I tell the network card which driver to use? Thanks in advance Stephan I found the problem. As described in stevens blog http://steveswinsburg.wordpress.com/2011/03/12/how-to-install-a-d-link-dwa-525-wireless-network-card-in-ubuntu-10-04/ sudo su make && make install "You need to use ‘sudo su’ and not just ‘sudo’ so it creates the directories properly." That is the problem with the solution describe above.

  Read the article

• Cannot Resolve Host Or Access Website Through Router

  - by Boris_yo

  This is weird. I am on Windows XP with Edimax BR 6204Wg. I have 3 devices - 2 laptops and 1 smartphone. 1st laptop and smartphone are connected through WiFi to router and 2nd laptop is connected through LAN to router. Before firmware upgrade i did not try to access website but after firmware upgrade to latest version: http://www.edimax.eu/en/support_detail.php?pd_id=11&pl1_id=3#02 i had problems resolving host, pinging, tracerting and accessing website. Sometimes ping and tracert work but i cannot access website and sometimes i can access website but ping and tracert do not work. Weird? I downgraded to previous version and no changes. If i can no longer access that website through Internet Explorer, i can access it in Firefox. I tried deleting cookies, clearing cache and that seem not make difference. Switching LAN port did not make difference. When i disconnect router and connect laptop through LAN to internet modem, everything is normal. I tried resetting router, resetting to factory default settings and all did not help. At the moment i can access website on laptop connected through LAN from Firefox and Internet Explorer, but on my smartphone i can access website only with Opera but not with built-in browser and Skyfire. UPDATE: I just could only access with Internet Explorer but not with other browsers on my PC. Minutes later i could access with all browsers. But on smartphone i could only access with Opera and not with other browsers. I am confused. I also determined that sometimes i can access and sometimes can't. What is also weird is that when ping and tracert cannot resolve host, i still am able to access website.

  Read the article

• Prepping the Raspberry Pi for Java Excellence (part 1)

  - by HecklerMark

  I've only recently been able to begin working seriously with my first Raspberry Pi, received months ago but hastily shelved in preparation for JavaOne. The Raspberry Pi and other diminutive computing platforms offer a glimpse of the potential of what is often referred to as the embedded space, the "Internet of Things" (IoT), or Machine to Machine (M2M) computing. I have a few different configurations I want to use for multiple Raspberry Pis, but for each of them, I'll need to perform the following common steps to prepare them for their various tasks: Load an OS onto an SD card Get the Pi connected to the network Load a JDK I've been very happy to see good friend and JFXtras teammate Gerrit Grunwald document how to do these things on his blog (link to article here - check it out!), but I ran into some issues configuring wi-fi that caused me some needless grief. Not knowing if any of the pitfalls were caused by my slightly-older version of the Pi and not being able to find anything specific online to help me get past it, I kept chipping away at it until I broke through. The purpose of this post is to (hopefully) help someone else recognize the same issues if/when they encounter them and work past them quickly. There is a great resource page here that covers several ways to get the OS on an SD card, but here is what I did (on a Mac): Plug SD card into reader on/in Mac Format it (FAT32) Unmount it (diskutil unmountDisk diskn, where n is the disk number representing the SD card) Transfer the disk image for Debian to the SD card (dd if=2012-08-08-wheezy-armel.img of=/dev/diskn bs=1m) Eject the card from the Mac (diskutil eject diskn) There are other ways, but this is fairly quick and painless, especially after you do it several times. Yes, I had to do that dance repeatedly (minus formatting) due to the wi-fi issues, as it kept killing the ability of the Pi to boot. You should be able to dramatically reduce the number of OS loads you do, though, if you do a few things with regard to your wi-fi. Firstly, I strongly recommend you purchase the Edimax EW-7811Un wi-fi adapter. This adapter/chipset has been proven with the Raspberry Pi, it's tiny, and it's cheap. Avoid unnecessary aggravation and buy this one! Secondly, visit this page for a script and instructions regarding how to configure your new wi-fi adapter with your Pi. Here is the rub, though: there is a missing step. At least for my combination of Pi version, OS version, and uncanny gift of timing and luck there was. :-) Here is the sequence of steps I used to make the magic happen: Plug your newly-minted SD card (with OS) into your Pi and connect a network cable (for internet connectivity) Boot your Pi. On the first boot, do the following things: Opt to have it use all space on the SD card (will require a reboot eventually) Disable overscan Set your timezone Enable the ssh server Update raspi-config Reboot your Pi. This will reconfigure the SD to use all space (see above). After you log in (UID: pi, password: raspberry), upgrade your OS. This was the missing step for me that put a merciful end to the repeated SD card re-imaging and made the wi-fi configuration trivial. To do so, just type sudo apt-get upgrade and give it several minutes to complete. Pour yourself a cup of coffee and congratulate yourself on the time you've just saved.  ;-) With the OS upgrade finished, now you can follow Mr. Engman's directions (to the letter, please see link above), download his script, and let it work its magic. One aside: I plugged the little power-sipping Edimax directly into the Pi and it worked perfectly. No powered hub needed, at least in my configuration. To recap, that OS upgrade (at least at this point, with this combination of OS/drivers/Pi version) is absolutely essential for a smooth experience. Miss that step, and you're in for hours of "fun". Save yourself! I'll pick up next time with more of the Java side of the RasPi configuration, but as they say, you have to cross the moat to get into the castle. Hopefully, this will help you do just that. Until next time! All the best, Mark 

  Read the article

• Wireless not working on ubuntu 12.04

  - by Yosef

  I just install ubuntu 12.04 but wirelless not works(windows 7 wirelless works). I open my windows 7 and see under Network Adapters: Edimax 802.11n Wireless Adapter Realtek PCIe GBE Family Controller Which drivers i should download to install them on ubuntu 12.04 to make wireless work? And how i install this drivers on ubuntu after i copy them to usb. (I can have only wireless connection not wire - soo i nhave to dowload the drivers with windows then copy them to ubuntu) Thanks

  Read the article

• Linux : Bridge dont forward if interface is wifi ?

  - by llazzaro

  Hello, I have an edimax (EW-7318USg) which comes with ralink rt73 and its USB. When trying to brigde (to share internet for example) it dont works. But Today I tried to do the same with a wired interface, same bridge, all same steps and I worked (with wired!). Could be that drivers, interface or other thing cant make the bridge with this wifi interface? (this is my question)

  Read the article

• Connecting 2 ubuntu machines as a LAN

  - by Brendan Cutjar

  Hi i am trying to connect 2 ubuntu computers as a LAN. In my current setup I have: One machine running ubuntu 11.10 with Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller While the other machine is running Ubuntu 12.04 with an Atheros Communications Inc AR8152 v1.1 Fast Ethernet The two machines are connected via a switch (Edimax ES-3205P). Unfortunately I still cannot connect the two machines together. Can somebody please show me what to do and how to go about solving this issue? Thank you ANSWERED All I had to do was set up both ip's maually, subnet mask to 255.255.255.0 and left blank both gateway and DNS.

  Read the article

• Upgrade to Xubuntu 11.04 Breaks Wireless

  - by fleamour

  When I tried to connect at my mother's house and then my brother's house; the little connection icon would circle forever before eventually prompting for password. I have triple checked all network keys & then some. Even with my home network I now have to revert to 10.04 LTS Lucid Lynx (dual boot) or wired Ethernet. Not even sure where to start trouble shooting TBH? My card is a Edimax EW-7108PCg PCMCIA card which I bought for it's out the box Linux compatibility. Hardware is an IBM Thinkpad T21.

  Read the article

• Slow internet using Arch Linux

  - by GZaidman

  after a week or so of using Arch Linux I cant access the internet - it takes around 5 mins to load google (most of the other websites just give me a timeout), pacman's downloading speed range between 5-2Kbs, and pinging google takes around 9Kms. I'm connected using wireless network (wifi card is Intel Ultimate 6300 and router is Edimax 6524n). Every other Windows machine that's connected to the network (and even the T410 running Windows) is fine, so the problem lies in Linux. So far, i checked the resolv.conf file (my router ip address is listed), and the hosts file (pretty much default), and I disabled the ipv6 module. None of that helped. PS: i'm using NetworkManager (but the problem still occurs when connecting using wicd) running on Gnome3. Thanks in advance for any help you can provide! EDIT: something really strange happens whenever I ping google: i get an unknown host 'google.com', but the bit rate from the card jumps at the exact second I ping google (so far, the bit rate jumped to 54Mb/s from 1Mb/s over the course of 4 pings).

  Read the article

• OS X will not register newly installed network adapters

  - by Chris

  I have purchased an Edimax 7318USg and tested it on a Windows machine (works). The installation process for the software for this adapter runs smoothly. However, OS X simply does not recognize new network adapters. When you go to System Preferences/Network, a new network adapter should be present/there should be an alert. This is not the case. Why might this be? Is there a setting I may reset to force the operating system to recognize this? Thanks!

  Read the article

• Multiple SSIDs better or worse

  - by swiss196

  I'm just setting up a network in a student house with 10 rooms, 3 floors. Configuration at the moment is as follows: Virgin Media 100mb Cable Virgin SuperHub on ground floor broadcasting on SSID1 Second AP(Edimax) wired on middle floor broadcasting on SSID2 These two networks server all 3 floors fairly well but I was wondering whether it would be better to setup an individual SSID for each floor (both the routers allow me to configure up to 3 ssids on each!). Would this help with speed issues, i.e if someone on the top floor is downloading/streaming etc, this wouldn't affect someone on the middle floor on a different SSID Or, will it have no effect? Thanks, Dave

  Read the article

• Ubuntu (11.10) fails to connect to wireless network

  - by Tal Galili

  I just installed ubuntu 11.10, and tried to have it connect to the internet. I use a wireless USB stick by edimax (it is called IEEE802.11b/g/n nano USB adapter or also EW-7811Un). My problem is that Ubuntu seems to be able to use the USB to see the networks around me, but when I try to connect to my network - it just keeps trying and failing. I am connected to the internet through a 300M Wireless N Router Model No. TL-WR841N / TL-WR841ND Can you please advise on how this can be resolved? Thanks!

  Read the article

• force connection using USB adapter

  - by James

  Hi all I am new to Linux, so even though this is probably a simple problem it remains unsolved after more then 3 hours of googling :-( I run running ubuntu 10.04 LTS on an Acer Aspire 5520G . the laptop has a wireless adapter, but since I wanted better range I got an Edimax EW-7711USN USB adapter. now , when running ifconfig I am able to see both adapters where as the laptop native adapter is listed as wlan0 and the usb adapter is listed as wlan1. but listing available networks from the wireless network applet , all the connection are listed under wlan0 , the usb adapter is costencly listed as disconnected. this is what I have been trying to do so far 1) ifconfig wlan0 down - I got disconnected from the net but still was not able to get the usb to connect 2) used the wireless connection dialog to connect to a hidden network with the usb adapter - I was able to connect to the network but with no Internet access 3) disable wireless using the laptop function button - both wireless adapters where disabled can anyone suggest a way to connect to to the wireless network using the USB adapter rather then the built in one ? Thanks

  Read the article

• connecting 2 ubuntu computers as a lan

  - by Brendan Cutjar

  Hi i am trying to connect 2 ubuntu computers as a LAN. In my current setup I have: One machine running ubuntu 11.10 with Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller While the other machine is running Ubuntu 12.04 with an Atheros Communications Inc AR8152 v1.1 Fast Ethernet The two machines are connected via a switch (Edimax ES-3205P). Unfortunately I still cannot connect the two machines together. Can somebody please show me what to do and how to go about solving this issue?

  Read the article

• Ubuntu 12.04 Network Connection Unavailable

  - by user211315

  I recently added a EDIMAX EW-7811Un to my computer to allow wireless networking. That was working. Now after a reboot I am unable to connect to either wireless or wired network. the result of ifconfig is ifconfig eth0 Link encap:Ethernet HWaddr bc:ae:c5:46:19:6d inet6 addr: fe80::beae:c5ff:fe46:196d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:231 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:62615 (62.6 KB) Interrupt:51 Base address:0x4000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:664 errors:0 dropped:0 overruns:0 frame:0 TX packets:664 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:52639 (52.6 KB) TX bytes:52639 (52.6 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

  Read the article

• Windows periodically disconnects, reconnects to the network

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it also happens. (When I initially wrote this question I didn't notice it.) ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM A result of some tests a couple of the disconnects: C:\Documents and Settings\eyalroz.BAKNUNIN>nslookup google.com DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 192.117.235.235: Timed out DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 62.219.186.7: Timed out *** Default servers are not available Server: UnKnown Address: 192.117.235.235 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out C:\Documents and Settings\eyalroz.BAKNUNIN>ping 194.90.1.5 Pinging 194.90.1.5 with 32 bytes of data: Control-C ^C C:\Documents and Settings\eyalroz.BAKNUNIN>tracert -d 194.90.1.5 Tracing route to 194.90.1.5 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.254 2 * * 11 ms 10.168.128.1 3 14 ms 13 ms 14 ms 212.179.160.142 4 * * * Request timed out. 5 * * * Request timed out. 6 * * 47 ms 62.219.189.169 7 31 ms 27 ms 32 ms 62.219.189.150 8 15 ms 14 ms 16 ms 192.114.65.202 9 15 ms 15 ms 11 ms 212.143.10.66 10 13 ms 29 ms 31 ms 212.143.12.234 11 35 ms 15 ms 18 ms 212.143.8.72 12 22 ms 22 ms 16 ms 194.90.1.5 I usually ping 194.90.1.5 (which is not at my ISP) with 15ms response time and no losses. Things I've done/tried: [2012-03-26] I replaced the cable; I thought that made a difference, but the disconnects were back a while later, so that wasn't it. Updated the NIC driver. Tried reducing the MTU (used a utility called Dr. TCP); there was no effect. I updated my board BIOS revision (which caused all the HW to be "reinstalled" or re-identified - successfully). I installed another NIC, and tried switching to it - same effect with the on-board NIC. A while back I tried another router (although it was an Edimax model) - same problem. Connected the computer directly, with no router. Same problem. ping -t to the router (192.168.0.254) gives pongs, nothing is lost, and time is < 1 ms almost always (sometimes it says 1 or 2 ms). This is the case also during the disconnects.

  Read the article

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

1 2  | Next Page >