Search Results

Search found 5 results on 1 pages for 'eigrp'.

Page 1/1 | 1 

• Are neighbors formed in EIGRP and OSPF always directly connectly?

  - by xczzhh

  I always thought that neighbors formed in EIGRP were not necessarily directly connected because the only requirement for two routers to be neighbors is that they share the same Autonomous System and K-values, but it seems that I was wrong. I have looked up several books, they do not seem to give a clear answer. And I am even more confused with OSPF... Please, give me some light here. Thank you.

  Read the article

• Tunnel is up but cannot ping directly connected network

  - by drmanalo

  We configured a site-to-site VPN and here is the topology. I control the network on the left but not the one on the right. All devices in our network has public IPs. Server---ASA5505---Cisco887======Internet=====ASA5510---devices I can see the tunnel is up and can do extended ping using a loopback interface. From the 10.175 and 10.165 networks, they can also ping my loopback address. I can also dial in using a Cisco VPN client, and can connect to the devices on the right. #show crypto session Crypto session current status Interface: Vlan3 Profile: xxx-profile Session status: UP-ACTIVE Peer: 213.121.x.x port 500 IKEv1 SA: local 77.245.x.x/500 remote 213.121.x.x/500 Active IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.175.0.0/255.255.128.0 Active SAs: 0, origin: crypto map IPSEC FLOW: permit ip 10.0.20.0/255.255.255.240 10.165.0.0/255.255.192.0 Active SAs: 2, origin: crypto map #ping 10.165.29.39 source loopback 2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.165.29.39, timeout is 2 seconds: Packet sent with a source address of 10.0.20.1 !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 16/17/20 ms My problem is the devices on the right cannot reach my server. They could only ping the loopback address and nothing else. I'm pasting some diagnostics related to routing thinking perhaps routing is my issue. I can paste all the running-config on my side of network if needed. #show ip int brief Interface IP-Address OK? Method Status Protocol ATM0 unassigned YES NVRAM administratively down down Ethernet0 unassigned YES NVRAM administratively down down FastEthernet0 unassigned YES unset up up connected to ASA FastEthernet1 unassigned YES unset administratively down down FastEthernet2 unassigned YES unset administratively down down FastEthernet3 unassigned YES unset up up Loopback1 10.0.20.65 YES NVRAM up up Loopback2 10.0.20.1 YES NVRAM up up Virtual-Template1 77.245.x.x YES unset up down Virtual-Template2 77.245.x.x YES unset up down Vlan1 unassigned YES unset down down Vlan3 77.245.x.x YES NVRAM up up connected to the Internet #show run | section ip route ip route 0.0.0.0 0.0.0.0 77.245.x.x ip route 213.121.240.36 255.255.255.255 Vlan3 #show access-list Extended IP access list 102 10 permit ip 10.0.20.0 0.0.0.15 10.175.0.0 0.0.127.255 (3332 matches) 20 permit ip 10.0.20.0 0.0.0.15 10.165.0.0 0.0.63.255 (3498 matches) #show vlan-switch VLAN Name Status Ports ---- -------------------------------- --------- ------------------------------- 1 default active 3 VLAN0003 active Fa0, Fa1, Fa2, Fa3 1002 fddi-default act/unsup 1003 token-ring-default act/unsup 1004 fddinet-default act/unsup 1005 trnet-default act/unsup #show ip route Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP + - replicated route, % - next hop override Gateway of last resort is 77.245.x.x to network 0.0.0.0 S* 0.0.0.0/0 [1/0] via 77.245.x.x 10.0.0.0/8 is variably subnetted, 5 subnets, 3 masks C 10.0.20.0/28 is directly connected, Loopback2 L 10.0.20.1/32 is directly connected, Loopback2 C 10.0.20.64/28 is directly connected, Loopback1 L 10.0.20.65/32 is directly connected, Loopback1 S 10.165.0.0/18 [1/0] via 213.121.x.x 77.0.0.0/8 is variably subnetted, 3 subnets, 3 masks S 77.0.0.0/8 [1/0] via 77.245.x.x C 77.245.x.x/29 is directly connected, Vlan3 L 77.245.x.x/32 is directly connected, Vlan3 213.121.x.0/32 is subnetted, 1 subnets S 213.121.x.x is directly connected, Vlan3 I read some of the posts here which lead to NATing issue but I'not sure of my next step. Should I translate my public address to private and route it to the loopback address? (only guessing) CISCO VPN site to site Site-to-Site VPN between two ASA 5505s only working in one direction Hope someone could help. Thanks in advance!

  Read the article

• Single-port 2600 router with 2900XL switch

  - by Slava Maslennikov

  I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

  Read the article

• Cisco 7206vxr cpu reducing

  - by naimson

  I have a 7206VXR (NPE-G2) . At the rate of 140 kpps i gain 80% of cpu . So i looking for ways how to reduce it? So i want to turn off netflow(but don't want to this,monitoring is highly important for me), but it will give me only 10-20% ? At this moment with 84kpps i have 58% sh processes cpu sorted give me this. PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 109 163534600 537236763 304 35.38% 32.83% 16.85% 0 IP Input 67 829396 52280 15864 0.15% 0.01% 0.00% 0 Per-minute Jobs 68 5542736 3053476 1815 0.15% 0.18% 0.16% 0 Per-Second Jobs 51 635852 1116315 569 0.07% 0.03% 0.02% 0 Net Background 329 120396 4607274 26 0.07% 0.00% 0.00% 0 EIGRP-IPv4 Hello 105 50508 95032488 0 0.07% 0.05% 0.05% 0 IPAM Manager 6 4068580 476916 8531 0.00% 0.07% 0.05% 0 Check heaps 7 7768 3634 2137 0.00% 0.00% 0.00% 0 Pool Manager 8 0 1 0 0.00% 0.00% 0.00% 0 DiscardQ Backgro 10 8 708 11 0.00% 0.00% 0.00% 0 WATCH_AFS 5 0 1 0 0.00% 0.00% 0.00% 0 RO Notify Timers 12 0 2 0 0.00% 0.00% 0.00% 0 ATM VC Auto Crea 9 0 2 0 0.00% 0.00% 0.00% 0 Timers 11 0 2 0 0.00% 0.00% 0.00% 0 ATM AutoVC Perio 13 296 610532 0 0.00% 0.00% 0.00% 0 IPC Event Notifi 16 0 1 0 0.00% 0.00% 0.00% 0 IPC Zone Manager 17 3584 2980311 1 0.00% 0.00% 0.00% 0 IPC Periodic Tim 4 0 1 0 0.00% 0.00% 0.00% 0 EDDRI_MAIN 19 0 1 0 0.00% 0.00% 0.00% 0 IPC Process leve 20 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat Manager 21 96 174453 0 0.00% 0.00% 0.00% 0 IPC Check Queue 14 4 50890 0 0.00% 0.00% 0.00% 0 IPC Dynamic Cach 3 0 1 0 0.00% 0.00% 0.00% 0 cpf_process_tpQ 24 756 305371 2 0.00% 0.00% 0.00% 0 IPC Keep Alive M 25 2340 610561 3 0.00% 0.00% 0.00% 0 IPC Loadometer 22 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat RX Cont 15 0 1 0 0.00% 0.00% 0.00% 0 IPC Session Serv 18 1620 2980310 0 0.00% 0.00% 0.00% 0 IPC Deferred Por 29 0 1 0 0.00% 0.00% 0.00% 0 Exception contro sh run(greped): http://pastie.org/5483194 Hardware: c7200p-adventerprisek9-mz.151-4.M1.bin Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory. Processor board ID 2xxxxxxx MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2 6 slot VXR midplane, Version 2.1

  Read the article

• Trying to configure HWIC-3G-HSPA

  - by user1174838

  I'm trying to configure a couple of Cisco 1941 routes. The are both identical routers. Each as a HWIC-1T (Smart Serial interface) and a HWIC-3G-HSPA 3G interface. These routers are to be sent to remote sites. We have connectivity to one of the sites but if remote site A gors down we lose connectivity to remote site B. The HWIC-1T is the primary WAN interface using frame relay joining the two remote sites We want the HWIC-3G-HSPA to be usable for direct connectivity from head office to remote site B, and also the HWIC-3G-HSPA is do be used for comms between the remote sites when the frame relay is down (happens quite a bit). I initialy tried to do dynamic routing using EIGRP however in my lab setup of laptop - 1941 - 1941 - laptop, I was unable to get end to end connectivity. I later settled on static routing and have got end to end connectivity but only over frame relay, not the HWIC-3G-HSPA. The sanitized running config for remote site A: version 15.1 service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service udp-small-servers service tcp-small-servers ! hostname remoteA ! boot-start-marker boot-end-marker ! ! logging buffered 51200 warnings enable secret 5 censored ! no aaa new-model clock timezone wst 8 0 ! no ipv6 cef ip source-route ip cef ! ip domain name yourdomain.com multilink bundle-name authenticated ! chat-script gsm "" "ATDT*98*1#" TIMEOUT 30 "CONNECT" ! username admin privilege 15 secret 5 censored ! controller Cellular 0/1 ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.2.5 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 ip address 10.1.1.2 255.255.255.252 encapsulation frame-relay cdp enable frame-relay interface-dlci 16 frame-relay lmi-type ansi ! interface Cellular0/1/0 ip address negotiated encapsulation ppp dialer in-band dialer idle-timeout 2147483 dialer string gsm dialer-group 1 async mode interactive ppp chap hostname censored ppp chap password 7 censored cdp enable ! interface Cellular0/1/1 no ip address encapsulation ppp ! interface Dialer0 no ip address ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 Serial0/0/0 210 permanent ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 220 permanent ip route 172.31.2.0 255.255.255.0 Cellular0/1/0 permanent ip route 192.168.3.0 255.255.255.0 10.1.1.1 permanent ip route 192.168.3.0 255.255.255.0 Cellular0/1/0 210 permanent ! access-list 1 permit any dialer-list 1 protocol ip list 1 ! control-plane ! line con 0 logging synchronous login local line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line 0/1/0 exec-timeout 0 0 script dialer gsm login modem InOut no exec transport input all rxspeed 7200000 txspeed 5760000 line 0/1/1 no exec rxspeed 7200000 txspeed 5760000 line vty 0 4 access-class 23 in privilege level 15 password 7 censored login local transport input all line vty 5 15 access-class 23 in privilege level 15 password 7 censored login local transport input all line vty 16 1370 password 7 censored login transport input all ! scheduler allocate 20000 1000 end The sanitized running config for remote site B: version 15.1 service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption service udp-small-servers service tcp-small-servers ! hostname remoteB ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings enable secret 5 censored ! no aaa new-model clock timezone wst 8 0 ! no ipv6 cef ip source-route ip cef ! no ip domain lookup ip domain name yourdomain.com multilink bundle-name authenticated ! chat-script gsm "" "ATDT*98*1#" TIMEOUT 30 "CONNECT" username admin privilege 15 secret 5 censored ! controller Cellular 0/1 ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.3.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 no ip address shutdown duplex auto speed auto ! interface Serial0/0/0 ip address 10.1.1.1 255.255.255.252 encapsulation frame-relay clock rate 2000000 cdp enable frame-relay interface-dlci 16 frame-relay lmi-type ansi frame-relay intf-type dce ! interface Cellular0/1/0 ip address negotiated encapsulation ppp dialer in-band dialer idle-timeout 2147483 dialer string gsm dialer-group 1 async mode interactive ppp chap hostname censored ppp chap password 7 censored ppp ipcp dns request cdp enable ! interface Cellular0/1/1 no ip address encapsulation ppp ! interface Dialer0 no ip address ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip route 0.0.0.0 0.0.0.0 Serial0/0/0 210 permanent ip route 0.0.0.0 0.0.0.0 Cellular0/1/0 220 permanent ip route 172.31.2.0 255.255.255.0 Cellular0/1/0 permanent ip route 192.168.2.0 255.255.255.0 10.1.1.2 permanent ip route 192.168.2.0 255.255.255.0 Cellular0/1/0 210 permanent ! kron occurrence PING in 1 recurring policy-list ICMP ! access-list 1 permit any dialer-list 1 protocol ip list 1 ! control-plane ! line con 0 logging synchronous login local line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line 0/1/0 exec-timeout 0 0 script dialer gsm login modem InOut no exec transport input all rxspeed 7200000 txspeed 5760000 line 0/1/1 no exec rxspeed 7200000 txspeed 5760000 line vty 0 4 access-class 23 in privilege level 15 password 7 censored login transport input all line vty 5 15 access-class 23 in privilege level 15 password 7 censored login transport input all line vty 16 1370 password 7 censored login transport input all ! scheduler allocate 20000 1000 end The last problem I'm having is the 3G interfaces go down after only a few minutes of inactivity. I've tried using kron to ping the local HWIC-3G-HSPA interface (cellular 0/1/0) every minute but that hasn't been successful. Manually pinging the IP assigned (by the telco) to ce0/1/0 does bring the interface up. Any ideas? Thanks

  Read the article

1