Search Results

Search found 3071 results on 123 pages for 'executing'.

Page 1/123 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• PSTN Trunk TDM400P Install on Asterisk / Trixbox

  - by Jona

  Hey All, I'm trying to get a TDM400P card with FXO module to connect to our PSTN line. The card is correctly detected by Linux: [trixbox1.localdomain asterisk]# lspci 00:09.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface I've run setup-pstn which produces the following output trixbox1.localdomain ~]# setup-pstn -------------------------------------------------------------- Detecting PSTN cards and USB PSTN Devices -------------------------------------------------------------- Hardware present! STOPPING ASTERISK Asterisk Stopped STOPPING FOP SERVER FOP Server Stopped Unloading DAHDI hardware modules: done Loading DAHDI hardware modules: wct4xxp: [ OK ] wcte12xp: [ OK ] wct1xxp: [ OK ] wcte11xp: [ OK ] wctdm24xxp: [ OK ] opvxa1200: [ OK ] wcfxo: [ OK ] wctdm: [ OK ] wcb4xxp: [ OK ] wctc4xxp: [ OK ] xpp_usb: [ OK ] Running dahdi_cfg: [ OK ] SETTING FILE PERMISSIONS Permissions OK STARTING ASTERISK Asterisk Started STARTING FOP SERVER FOP Server Started Chan Extension Context Language MOH Interpret Blocked State pseudo default en default In Service 1 from-pstn en default In Service dahdi_scan returns: dahdi_scan [1] active=yes alarms=OK description=Wildcard TDM400P REV I Board 5 name=WCTDM/4 manufacturer=Digium devicetype=Wildcard TDM400P REV I location=PCI Bus 00 Slot 10 basechan=1 totchans=4 irq=209 type=analog port=1,FXO port=2,none port=3,none port=4,none And asterisk can see the channel: > trixbox1*CLI> dahdi show channel 1 > Channel: 1LI> File Descriptor: 14 > Span: 11*CLI> Extension: I> Dialing: > noI> Context: from-pstn Caller ID: I> > Calling TON: 0 Caller ID name: > Mailbox: none Destroy: 0LI> InAlarm: > 1LI> Signalling Type: FXS Kewlstart > Radio: 0*CLI> Owner: <None> Real: > <None>> Callwait: <None> Threeway: > <None> Confno: -1LI> Propagated > Conference: -1 Real in conference: 0 > DSP: no1*CLI> Busy Detection: no TDD: > no1*CLI> Relax DTMF: no > Dialing/CallwaitCAS: 0/0 Default law: > ulaw Fax Handled: no Pulse phone: no > DND: no1*CLI> Echo Cancellation: > trixbox1128 taps trixbox1(unless TDM > bridged) currently OFF Actual > Confinfo: Num/0, Mode/0x0000 Actual > Confmute: No > Hookstate (FXS only): Onhook A cat of /etc/asterisk/dahdi.conf shows: [trixbox1.localdomain ~]# cat /etc/asterisk/dahdi-channels.conf ; Autogenerated by /usr/sbin/dahdi_genconf on Tue May 25 17:45:13 2010 ; If you edit this file and execute /usr/sbin/dahdi_genconf again, ; your manual changes will be LOST. ; Dahdi Channels Configurations (chan_dahdi.conf) ; ; This is not intended to be a complete chan_dahdi.conf. Rather, it is intended ; to be #include-d by /etc/chan_dahdi.conf that will include the global settings ; ; Span 1: WCTDM/4 "Wildcard TDM400P REV I Board 5" (MASTER) ;;; line="1 WCTDM/4/0 FXSKS (SWEC: MG2)" signalling=fxs_ks callerid=asreceived group=0 context=from-pstn channel => 1 callerid= group= context=default I have configured a "ZAP Trunk (DAHDI compatibility Mode)" with the ZAP identifier 1 and an outbound route, but when ever I try to make an external call via it I get the "All Circuits are busy now, please try your call again later message". I have one outbound route which uses the dial pattern 9|. and the Trunk Zap/1 and one Zap Trunk which uses Zap Identifier (trunk name): 1 and has no Dial Rules. The FXO module is directly connected to our phone line from BT via a BT-RJ11 cable. When running tail -f /var/log/asterisk/full and placing a call I get the following output: [May 26 11:10:52] VERBOSE[2723] logger.c: == Using SIP RTP TOS bits 184 [May 26 11:10:52] VERBOSE[2723] logger.c: == Using SIP RTP CoS mark 5 [May 26 11:10:52] VERBOSE[2723] logger.c: == Using SIP VRTP TOS bits 136 [May 26 11:10:52] VERBOSE[2723] logger.c: == Using SIP VRTP CoS mark 6 [May 26 11:10:52] WARNING[2661] pbx.c: FONALITY: This thread has already held the conlock, skip locking [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [901483890915@from-internal:1] Macro("SIP/801-b7ce8c28", "user-callerid,SKIPTTL,") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:1] Set("SIP/801-b7ce8c28", "AMPUSER=801") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:2] GotoIf("SIP/801-b7ce8c28", "0?report") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:3] ExecIf("SIP/801-b7ce8c28", "1?Set(REALCALLERIDNUM=801)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:4] Set("SIP/801-b7ce8c28", "AMPUSER=801") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:5] Set("SIP/801-b7ce8c28", "AMPUSERCIDNAME=Jona") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:6] GotoIf("SIP/801-b7ce8c28", "0?report") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:7] Set("SIP/801-b7ce8c28", "AMPUSERCID=801") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:8] Set("SIP/801-b7ce8c28", "CALLERID(all)="Jona" <801>") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:9] Set("SIP/801-b7ce8c28", "REALCALLERIDNUM=801") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:10] ExecIf("SIP/801-b7ce8c28", "0?Set(CHANNEL(language)=)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:11] GotoIf("SIP/801-b7ce8c28", "1?continue") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Goto (macro-user-callerid,s,20) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-user-callerid:20] NoOp("SIP/801-b7ce8c28", "Using CallerID "Jona" <801>") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [901483890915@from-internal:2] Set("SIP/801-b7ce8c28", "_NODEST=") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [901483890915@from-internal:3] Macro("SIP/801-b7ce8c28", "record-enable,801,OUT,") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-record-enable:1] GotoIf("SIP/801-b7ce8c28", "1?check") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Goto (macro-record-enable,s,4) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-record-enable:4] AGI("SIP/801-b7ce8c28", "recordingcheck,20100526-111052,1274868652.1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Launched AGI Script /var/lib/asterisk/agi-bin/recordingcheck [May 26 11:10:52] VERBOSE[2858] logger.c: recordingcheck,20100526-111052,1274868652.1: Outbound recording not enabled [May 26 11:10:52] VERBOSE[2858] logger.c: -- <SIP/801-b7ce8c28>AGI Script recordingcheck completed, returning 0 [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-record-enable:5] MacroExit("SIP/801-b7ce8c28", "") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [901483890915@from-internal:4] Macro("SIP/801-b7ce8c28", "dialout-trunk,1,01483890915,") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:1] Set("SIP/801-b7ce8c28", "DIAL_TRUNK=1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:2] GosubIf("SIP/801-b7ce8c28", "0?sub-pincheck,s,1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:3] GotoIf("SIP/801-b7ce8c28", "0?disabletrunk,1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:4] Set("SIP/801-b7ce8c28", "DIAL_NUMBER=01483890915") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:5] Set("SIP/801-b7ce8c28", "DIAL_TRUNK_OPTIONS=tr") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:6] Set("SIP/801-b7ce8c28", "OUTBOUND_GROUP=OUT_1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:7] GotoIf("SIP/801-b7ce8c28", "1?nomax") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Goto (macro-dialout-trunk,s,9) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:9] GotoIf("SIP/801-b7ce8c28", "0?skipoutcid") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:10] Set("SIP/801-b7ce8c28", "DIAL_TRUNK_OPTIONS=") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:11] Macro("SIP/801-b7ce8c28", "outbound-callerid,1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:1] ExecIf("SIP/801-b7ce8c28", "0?Set(CALLERPRES()=)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:2] ExecIf("SIP/801-b7ce8c28", "0?Set(REALCALLERIDNUM=801)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:3] GotoIf("SIP/801-b7ce8c28", "1?normcid") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Goto (macro-outbound-callerid,s,6) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:6] Set("SIP/801-b7ce8c28", "USEROUTCID=") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:7] Set("SIP/801-b7ce8c28", "EMERGENCYCID=") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:8] Set("SIP/801-b7ce8c28", "TRUNKOUTCID=") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:9] GotoIf("SIP/801-b7ce8c28", "1?trunkcid") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Goto (macro-outbound-callerid,s,12) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:12] ExecIf("SIP/801-b7ce8c28", "0?Set(CALLERID(all)=)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:13] ExecIf("SIP/801-b7ce8c28", "0?Set(CALLERID(all)=)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outbound-callerid:14] ExecIf("SIP/801-b7ce8c28", "0?Set(CALLERPRES()=prohib_passed_screen)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:12] ExecIf("SIP/801-b7ce8c28", "0?AGI(fixlocalprefix)") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:13] Set("SIP/801-b7ce8c28", "OUTNUM=01483890915") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:14] Set("SIP/801-b7ce8c28", "custom=DAHDI/1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:15] ExecIf("SIP/801-b7ce8c28", "0?Set(DIAL_TRUNK_OPTIONS=M(setmusic^))") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:16] Macro("SIP/801-b7ce8c28", "dialout-trunk-predial-hook,") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk-predial-hook:1] MacroExit("SIP/801-b7ce8c28", "") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:17] GotoIf("SIP/801-b7ce8c28", "0?bypass,1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:18] GotoIf("SIP/801-b7ce8c28", "0?customtrunk") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:19] Dial("SIP/801-b7ce8c28", "DAHDI/1/01483890915,300,") in new stack [May 26 11:10:52] WARNING[2858] app_dial.c: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) [May 26 11:10:52] VERBOSE[2858] logger.c: == Everyone is busy/congested at this time (1:0/0/1) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-dialout-trunk:20] Goto("SIP/801-b7ce8c28", "s-CHANUNAVAIL,1") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Goto (macro-dialout-trunk,s-CHANUNAVAIL,1) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s-CHANUNAVAIL@macro-dialout-trunk:1] GotoIf("SIP/801-b7ce8c28", "1?noreport") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Goto (macro-dialout-trunk,s-CHANUNAVAIL,3) [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s-CHANUNAVAIL@macro-dialout-trunk:3] NoOp("SIP/801-b7ce8c28", "TRUNK Dial failed due to CHANUNAVAIL (hangupcause: 0) - failing through to other trunks") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [901483890915@from-internal:5] Macro("SIP/801-b7ce8c28", "outisbusy,") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- Executing [s@macro-outisbusy:1] Playback("SIP/801-b7ce8c28", "all-circuits-busy-now,noanswer") in new stack [May 26 11:10:52] VERBOSE[2858] logger.c: -- <SIP/801-b7ce8c28> Playing 'all-circuits-busy-now.ulaw' (language 'en') [May 26 11:10:54] VERBOSE[2858] logger.c: -- Executing [s@macro-outisbusy:2] Playback("SIP/801-b7ce8c28", "pls-try-call-later,noanswer") in new stack [May 26 11:10:54] VERBOSE[2858] logger.c: -- <SIP/801-b7ce8c28> Playing 'pls-try-call-later.ulaw' (language 'en') [May 26 11:10:54] WARNING[2661] pbx.c: FONALITY: This thread has already held the conlock, skip locking [May 26 11:10:54] VERBOSE[2858] logger.c: == Spawn extension (macro-outisbusy, s, 2) exited non-zero on 'SIP/801-b7ce8c28' in macro 'outisbusy' [May 26 11:10:54] VERBOSE[2858] logger.c: == Spawn extension (from-internal, 901483890915, 5) exited non-zero on 'SIP/801-b7ce8c28' [May 26 11:10:54] VERBOSE[2858] logger.c: -- Executing [h@from-internal:1] Macro("SIP/801-b7ce8c28", "hangupcall") in new stack [May 26 11:10:54] VERBOSE[2858] logger.c: -- Executing [s@macro-hangupcall:1] ResetCDR("SIP/801-b7ce8c28", "vw") in new stack [May 26 11:10:54] VERBOSE[2858] logger.c: -- Executing [s@macro-hangupcall:2] NoCDR("SIP/801-b7ce8c28", "") in new stack [May 26 11:10:54] VERBOSE[2858] logger.c: -- Executing [s@macro-hangupcall:3] GotoIf("SIP/801-b7ce8c28", "1?skiprg") in new stack [May 26 11:10:54] VERBOSE[2858] logger.c: -- Goto (macro-hangupcall,s,6) [May 26 11:10:55] VERBOSE[2858] logger.c: -- Executing [s@macro-hangupcall:6] GotoIf("SIP/801-b7ce8c28", "1?skipblkvm") in new stack [May 26 11:10:55] VERBOSE[2858] logger.c: -- Goto (macro-hangupcall,s,9) [May 26 11:10:55] VERBOSE[2858] logger.c: -- Executing [s@macro-hangupcall:9] GotoIf("SIP/801-b7ce8c28", "1?theend") in new stack [May 26 11:10:55] VERBOSE[2858] logger.c: -- Goto (macro-hangupcall,s,11) [May 26 11:10:55] VERBOSE[2858] logger.c: -- Executing [s@macro-hangupcall:11] Hangup("SIP/801-b7ce8c28", "") in new stack [May 26 11:10:55] VERBOSE[2858] logger.c: == Spawn extension (macro-hangupcall, s, 11) exited non-zero on 'SIP/801-b7ce8c28' in macro 'hangupcall' [May 26 11:10:55] VERBOSE[2858] logger.c: == Spawn extension (from-internal, h, 1) exited non-zero on 'SIP/801-b7ce8c28' I'm guessing I've missed a configuration step somewhere but no idea where, any help greatly appreciated.

  Read the article

• Python ImportError when executing 'import.py', but not when executing 'python import.py'

  - by Martin Del Vecchio

  I am running Cygwin Python version 2.5.2. I have a three-line source file, called import.py: #!/usr/bin/python import xml.etree.ElementTree as ET print "Success!" When I execute "python import.py", it works: C:\Temp>python import.py Success! When I run the python interpreter and type the commands, it works: C:\Temp>python Python 2.5.2 (r252:60911, Dec 2 2008, 09:26:14) [GCC 3.4.4 (cygming special, gdc 0.12, using dmd 0.125)] on cygwin Type "help", "copyright", "credits" or "license" for more information. >>> #!/usr/bin/python ... import xml.etree.ElementTree as ET >>> print "Success!" Success! >>> But when I execute "import.py', it does not work: C:\Temp>which python /usr/bin/python C:\Temp>import.py Traceback (most recent call last): File "C:\Temp\import.py", line 2, in ? import xml.etree.ElementTree as ET ImportError: No module named etree.ElementTree When I remove the first line (#!/usr/bin/python), I get the same error. I need that line in there, though, for when this script runs on Linux. And it works fine on Linux. Any ideas? Thanks.

  Read the article

• Self-Executing Anonymous Function vs Prototype

  - by Robotsushi

  In Javascript there are a few clearly prominent techniques for create and manage classes/namespaces in javascript. I am curious what situations warrant using one technique vs. the other. I want to pick one and stick with it moving forward. I write enterprise code that is maintained and shared across multiple teams, and I want to know what is the best practice when writing maintainable javascript ? I tend to prefer Self-Executing Anonymous Functions however I am curious what the community vote is on these techniques. Prototype : function obj() { } obj.prototype.test = function() { alert('Hello?'); }; var obj2 = new obj(); obj2.test(); Self-Closing Anonymous Function : //Self-Executing Anonymous Function (function( skillet, $, undefined ) { //Private Property var isHot = true; //Public Property skillet.ingredient = "Bacon Strips"; //Public Method skillet.fry = function() { var oliveOil; addItem( "\t\n Butter \n\t" ); addItem( oliveOil ); console.log( "Frying " + skillet.ingredient ); }; //Private Method function addItem( item ) { if ( item !== undefined ) { console.log( "Adding " + $.trim(item) ); } } }( window.skillet = window.skillet || {}, jQuery )); //Public Properties console.log( skillet.ingredient ); //Bacon Strips //Public Methods skillet.fry(); //Adding Butter & Fraying Bacon Strips //Adding a Public Property skillet.quantity = "12"; console.log( skillet.quantity ); //12 //Adding New Functionality to the Skillet (function( skillet, $, undefined ) { //Private Property var amountOfGrease = "1 Cup"; //Public Method skillet.toString = function() { console.log( skillet.quantity + " " + skillet.ingredient + " & " + amountOfGrease + " of Grease" ); console.log( isHot ? "Hot" : "Cold" ); }; }( window.skillet = window.skillet || {}, jQuery )); //end of skillet definition try { //12 Bacon Strips & 1 Cup of Grease skillet.toString(); //Throws Exception } catch( e ) { console.log( e.message ); //isHot is not defined } I feel that I should mention that the Self-Executing Anonymous Function is the pattern used by the jQuery team. Update When I asked this question I didn't truly see the importance of what I was trying to understand. The real issue at hand is whether or not to use new to create instances of your objects or to use patterns which do not require constructors of the use of the new keyword. I added my own answer, because in my opinion we should make use of patterns which don't use the new keyword. For more information please see my answer.

  Read the article

• Conditionally Auto-Executing af:query Search Form Based on User Input

  - by steve.muench

  Due to extreme lack of time due to other work priorities -- working hard on some interesting new ADF features for a future major release -- 2010 has not been a banner year for my production of samples to post to my blog, but to show my heart is in the right place I wanted to close out the year by posting example# 160: 160. Conditionally Auto-Executing af:query Search Form Based on User Input Enjoy. Happy New Year.

  Read the article

• Executing Stored Procedures in Visual Studio LightSwitch.

  - by dataintegration

  A LightSwitch Project is very easy way to visualize and manipulate information directly from one of our ADO.NET Providers. But when it comes to executing the Stored Procedures, it can be a bit more complicated. In this article, we will demonstrate how to execute a Stored Procedure in LightSwitch. For the purposes of this article, we will be using the RSSBus Email Data Provider, but the same process will work with any of our ADO.NET Providers. Creating the RIA Service. Step 1: Open Visual Studio and create a new WCF RIA Service Class Project. Step 2:Add the reference to the RSSBus Email Data Provider dll in the (ProjectName).Web project. Step 3: Add a new Domain Service Class to the (ProjectName).Web project. Step 4: In the new Domain Service Class, create a new class with the attributes needed for the Stored Procedure's parameters. In this demo, the Stored Procedure we are executing is called SendMessage. The parameters we will need are as follows: public class NewMessage{ [Key] public int ID { get; set; } public string FromEmail { get; set; } public string ToEmail { get; set; } public string Subject { get; set; } public string Text { get; set; } } Note: The created class must have an ID which will serve as the key value. Step 5: Create a new method that will executed when the insert event fires. Inside this method you can use the standards ADO.NET code which will execute the stored procedure. [Insert] public void SendMessage(NewMessage newMessage) { try { EmailConnection conn = new EmailConnection(connectionString); EmailCommand comm = new EmailCommand("SendMessage", conn); comm.CommandType = System.Data.CommandType.StoredProcedure; if (!newMessage.FromEmail.Equals("")) comm.Parameters.Add(new EmailParameter("@From", newMessage.FromEmail)); if (!newMessage.ToEmail.Equals("")) comm.Parameters.Add(new EmailParameter("@To", newMessage.ToEmail)); if (!newMessage.Subject.Equals("")) comm.Parameters.Add(new EmailParameter("@Subject", newMessage.Subject)); if (!newMessage.Text.Equals("")) comm.Parameters.Add(new EmailParameter("@Text", newMessage.Text)); comm.ExecuteNonQuery(); } catch (Exception exc) { Console.WriteLine(exc.Message); } } Step 6: Create a query method. We are not going to be using getNewMessages(), so it does not matter what it returns for the purpose of our example, but you will need to create a method for the query event as well. [Query(IsDefault=true)] public IEnumerable<NewMessage> getNewMessages() { return null; } Step 7: Rebuild the whole solution. Creating the LightSwitch Project. Step 8: Open Visual Studio and create a new LightSwitch Application Project. Step 9: On the Data Sources, add a new data source. Choose a WCF RIA Service Step 10: Choose to add a new reference and select the (Project Name).Web.dll generated from the RIA Service. Step 11: Select the entities you would like to import. In this case, we are using the recently created NewMessage entity. Step 13: On the Screens section, create a new screen and select the NewMessage entity as the Screen Data. Step 14: After you run the project, you will be able to add a new record and save it. This will execute the Stored Procedure and send the new message. If you create a screen to check the sent messages, you can refresh this screen to see the mail you sent. Sample Project To help you with get started using stored procedures in LightSwitch, download the fully functional sample project. You will also need the RSSBus Email Data Provider to make the connection. You can download a free trial here.

  Read the article

• Executing Shell Commands - PHP or Python?

  - by chadpeppers

  I know basically two languages: Python and PHP. I am primarily a Drupal developer. I have a great idea in creating a command line program that will help some of the mundane tasks and bring my efficiency up quite a bit. The concept is that of a complete console program, almost like the days when I learned C++ using stdin/out. I want to use this came concept but for this program. I am going to be executing shell commands (mainly drush commands, if you are familiar with drush its drupals way of doing tasks like installing drupal, clearing cache, and other things). I am also wanting to do a database and save/execute through multiple objects and site profiles. My general question is this. Which language would be better suited to handle command line code? Drupal is written in PHP so I am leaned more towards that,but I know python seems to handle console programming a bit easier. Any help would be great!

  Read the article

• Wubi 12.04 installation error executing command command

  - by Erik Lau

  I have tried to install wubi but have not had luck because there is an error executing command: command=C:\Users\Me\AppData\Local\Temp\pyl4266.tmp\bin\resize2fs.exe-f C:\ubuntu\disks\root.disk 17744M retval=1 stderr= stdout=resize2fs1.40.6 (09-Feb-2008) Usage: /cygdrive/c/Users/Eriks/AppData/Local/Temp/pyl4266.tmp/bin/resize2fs.exe-f C:/unbuntu/disks.root.disk17744M [-d debug_flags][-f][-F][-p] device[new_size] I do not understand what is the problem. Here is my log file. https://skydrive.live.com/redir?resid=B4F19CA027FFAD89!324 Please let me know what can be done to fix this error.

  Read the article

• Executing server validators first before OnClientClick Javascript confirm/alert

  - by kaushalparik27

  I got to answer a simple question over community forums. Consider this: Suppose you are developing a webpage with few input controls and a submit button. You have placed some server validator controls like RequiredFieldValidator to validate the inputs entered by the user. Once user fill-in all the details and try to submit the page via button click you want to alert/confirm the submission like "Are you sure to modify above details?". You will consider to use javascript on click of the button.Everything seems simple and you are almost done. BUT, when you run the page; you will see that Javascript alert/confirm box is executing first before server validators try to validate the input controls! Well, this is expected behaviour. BUT, this is not you want. Then? The simple answer is: Call Page_ClientValidate() in javascript where you are alerting the submission. Below is the javascript example:    <script type="text/javascript" language="javascript">        function ValidateAllValidationGroups() {            if (Page_ClientValidate()) {                return confirm("Are you sure to modify above details?");            }        }    </script>Page_ClientValidate() function tests for all server validators and return bool value depends on whether the page meets defined validation criteria or not. In above example, confirm alert will only popup up if Page_ClientValidate() returns true (if all validations satisfy). You can also specify ValidationGroup inside this function as Page_ClientValidate('ValidationGroup1') to only validate a specific group of validation in your page.        function ValidateSpecificValidationGroup() {            if (Page_ClientValidate('ValidationGroup1')) {                return confirm("Are you sure to modify above details?");            }        }I have attached a sample example with this post here demonstrating both above cases. Hope it helps./.

  Read the article

• Executing legacy MSBuild scripts in TFS 2010 Build

  - by Jakob Ehn

  When upgrading from TFS 2008 to TFS 2010, all builds are “upgraded” in the sense that a build definition with the same name is created, and it uses the UpgradeTemplate  build process template to execute the build. This template basically just runs MSBuild on the existing TFSBuild.proj file. The build definition contains a property called ConfigurationFolderPath that points to the TFSBuild.proj file. So, existing builds will run just fine after upgrade. But what if you want to use the new workflow functionality in TFS 2010 Build, but still have a lot of MSBuild scripts that maybe call custom MSBuild tasks that you don’t have the time to rewrite? Then one option is to keep these MSBuild scrips and call them from a TFS 2010 Build workflow. This can be done using the MSBuild workflow activity that is avaiable in the toolbox in the Team Foundation Build Activities section: This activity wraps the call to MSBuild.exe and has the following parameters: Most of these properties are only relevant when actually compiling projects, for example C# project files. When calling custom MSBuild project files, you should focus on these properties: Property Meaning Example CommandLineArguments Use this to send in/override MSBuild properties in your project “/p:MyProperty=SomeValue” or MSBuildArguments (this will let you define the arguments in the build definition or when queuing the build) LogFile Name of the log file where MSbuild will log the output “MyBuild.log” LogFileDropLocation Location of the log file BuildDetail.DropLocation + “\log” Project The project to execute SourcesDirectory + “\BuildExtensions.targets” ResponseFile The name of the MSBuild response file SourcesDirectory + “\BuildExtensions.rsp” Targets The target(s) to execute New String() {“Target1”, “Target2”} Verbosity Logging verbosity Microsoft.TeamFoundation.Build.Workflow.BuildVerbosity.Normal Integrating with Team Build   If your MSBuild scripts tries to use Team Build tasks, they will most likely fail with the above approach. For example, the following MSBuild project file tries to add a build step using the BuildStep task:   <?xml version="1.0" encoding="utf-8"?> <Project ToolsVersion="4.0" xmlns="http://schemas.microsoft.com/developer/msbuild/2003"> <Import Project="$(MSBuildExtensionsPath)\Microsoft\VisualStudio\TeamBuild\Microsoft.TeamFoundation.Build.targets" /> <Target Name="MyTarget"> <BuildStep TeamFoundationServerUrl="$(TeamFoundationServerUrl)" BuildUri="$(BuildUri)" Name="MyBuildStep" Message="My build step executed" Status="Succeeded"></BuildStep> </Target> </Project> When executing this file using the MSBuild activity, calling the MyTarget, it will fail with the following message: The "Microsoft.TeamFoundation.Build.Tasks.BuildStep" task could not be loaded from the assembly \PrivateAssemblies\Microsoft.TeamFoundation.Build.ProcessComponents.dll. Could not load file or assembly 'file:///D:\PrivateAssemblies\Microsoft.TeamFoundation.Build.ProcessComponents.dll' or one of its dependencies. The system cannot find the file specified. Confirm that the <UsingTask> declaration is correct, that the assembly and all its dependencies are available, and that the task contains a public class that implements Microsoft.Build.Framework.ITask. You can see that the path to the ProcessComponents.dll is incomplete. This is because in the Microsoft.TeamFoundation.Build.targets file the task is referenced using the $(TeamBuildRegPath) property. Also note that the task needs the TeamFounationServerUrl and BuildUri properties. One solution here is to pass these properties in using the Command Line Arguments parameter:   Here we pass in the parameters with the corresponding values from the curent build. The build log shows that the build step has in fact been inserted:   The problem as you probably spted is that the build step is insert at the top of the build log, instead of next to the MSBuild activity call. This is because we are using a legacy team build task (BuildStep), and that is how these are handled in TFS 2010. You can see the same behaviour when running builds that are using the UpgradeTemplate, that cutom build steps shows up at the top of the build log.

  Read the article

• Problem with executing dssp (secondary structure assignment)

  - by Mana

  I followed a previous post to install dssp on ubuntu How to install dssp (secondary structure assignments) under 12.04? After the installation I tried to execute dssp which was in /usr/local/bin/dssp But it gave me the following error bash: /usr/local/bin/dssp: cannot execute binary file Also I tried to analyse some trajectory files from a simulation using the code do_dssp -s md.tpr -f traj.xtc But it also failed giving me the error below Reading file md.tpr, VERSION 4.5.5 (single precision) Reading file md.tpr, VERSION 4.5.5 (single precision) Segmentation fault (core dumped) Please post me a solution for this problem. Thank you!

  Read the article

• System.Threading.ThreadAbortException executing WCF service

  - by SURESH GIRIRAJAN

  In one of our prod server we recently ran into issue when we went and update the web.config and try to browse the service. We started seeing the service was not responding and getting the following warning in the application log. Our service is WCF service, BizTalk orchestration exposed as service. We have other prod server where we never ran into this issue, so what’s different with this server. After going thru lot of forum and came up on some Microsoft service pack and hot fix which related to FCN. But I don’t want to apply any patch on this server then we need to do on all the other servers too. So solution is simple, I dropped the existing website, created a new site with different name with updated web.config browse the service. Then dropped that site and recreate the original web site and it worked fine without any issue. Event Viewer:  Event Type:        Warning Event Source:    ASP.NET 2.0.50727.0 Event Category:                Web Event Event ID:              1309 Date:                     6/6/2011 Time:                    5:41:42 PM User:                     N/A Computer:          PRODP02 Description: Event code: 3005 Event message: An unhandled exception has occurred. Event time: 6/6/2011 5:41:42 PM Event time (UTC): 6/6/2011 9:41:42 PM Event ID: a71769f42b304355a58c482bfec267f2 Event sequence: 3 Event occurrence: 1 Event detail code: 0  Application information:     Application domain: /LM/W3SVC/518296899/ROOT/PortArrivals-2-129518698821558995     Trust level: Full     Application Virtual Path: /TESTSVC     Application Path: D:\inetpub\wwwroot\RFID\TESTSVC\     Machine name: PRODP02  Process information:     Process ID: 8752     Process name: w3wp.exe     Account name: domain\BizTalk_Svc_Hostlso  Exception information:     Exception type: ThreadAbortException     Exception message: Thread was being aborted.  Request information:     Request URL: http://localhost:81/TESTSVC/TESTSVCS.svc     Request path: /TESTSVC/TESTSVCS.svc     User host address: 127.0.0.1     User:      Is authenticated: False     Authentication Type:      Thread account name: domain\BizTalk_Svc_Hostlso  Thread information:     Thread ID: 22     Thread account name: domain\BizTalk_Svc_Hostlso     Is impersonating: False     Stack trace:    at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously)    at System.Web.HttpApplication.ApplicationStepManager.ResumeSteps(Exception error)  at System.Web.HttpApplication.System.Web.IHttpAsyncHandler.BeginProcessRequest(HttpContext context, AsyncCallback cb, Object extraData)    at System.Web.HttpRuntime.ProcessRequestInternal(HttpWorkerRequest wr)  <Description>Handling an exception.</Description> <AppDomain>/LM/W3SVC/518296899/ROOT/TESTSVC-6-129518741899334691</AppDomain> <Exception> <ExceptionType>System.Threading.ThreadAbortException, mscorlib, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b77a5c561934e089</ExceptionType> <Message>Thread was being aborted.</Message> <StackTrace> at System.Threading.Monitor.Enter(Object obj) at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath) at System.ServiceModel.ServiceHostingEnvironment.EnsureServiceAvailableFast(String relativeVirtualPath) at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.HandleRequest() at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.BeginRequest() at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.OnBeginRequest(Object state) at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.WorkItem.Invoke2() at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.WorkItem.Invoke() at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.ProcessCallbacks() at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.CompletionCallback(Object state) at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.ScheduledOverlapped.IOCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* nativeOverlapped) at System.ServiceModel.Diagnostics.Utility.IOCompletionThunk.UnhandledExceptionFrame(UInt32 error, UInt32 bytesRead, NativeOverlapped* nativeOverlapped) </StackTrace> <ExceptionString>System.Threading.ThreadAbortException: Thread was being aborted.    at System.Threading.Monitor.Enter(Object obj)    at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath)    at System.ServiceModel.ServiceHostingEnvironment.EnsureServiceAvailableFast(String relativeVirtualPath)    at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.HandleRequest()    at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.BeginRequest()    at System.ServiceModel.Activation.HostedHttpRequestAsyncResult.OnBeginRequest(Object state)    at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.WorkItem.Invoke2()    at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.WorkItem.Invoke()    at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.ProcessCallbacks()    at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.CompletionCallback(Object state)    at System.ServiceModel.Channels.IOThreadScheduler.CriticalHelper.ScheduledOverlapped.IOCallback(UInt32 errorCode, UInt32 numBytes, NativeOverlapped* nativeOverlapped)    at System.ServiceModel.Diagnostics.Utility.IOCompletionThunk.UnhandledExceptionFrame(UInt32 error, UInt32 bytesRead, NativeOverlapped* nativeOverlapped)</ExceptionString>

  Read the article

• Executing a Batch file from remote Ax client on an AOS server

  - by Anisha

  Is it possible to execute a batch file on an AOS server from a remote AX client? Answer is yes, provided you have necessary permission for this execution on the server. Please create a batch file on your AOS server. Some thing as below for creating a directory on the server.    Insert a command something like this in a .BAT file (batch file) and place any were on the server.   Mkdir “c:\test”      Copy the following code into your server static method of your class and call this piece of code from a button click on Ax form. Please execute this button click from a remote AX client and see the result . This should execute the batch file on the server and should create a directory called ‘test’ on the root directoryof the server.     server static void AOS_batch_file_create() { boolean b; System.Diagnostics.Process process; System.Diagnostics.ProcessStartInfo processStartInfo; ; b = Global::isRunningOnServer(); infolog.add(0, int2str(b)); new InteropPermission(InteropKind::ClrInterop).assert(); process = new System.Diagnostics.Process(); processStartInfo = new System.Diagnostics.ProcessStartInfo(); processStartInfo.set_FileName("C:\\create_dir.bat"); // batch file path on the AOS server process.set_StartInfo(processStartInfo); process.Start(); //process.Refresh(); //process.Close(); //process.WaitForExit(); info("Finished"); }

  Read the article

• Setting environment variables when executing Eclipse via Unity launcher icon

  - by Nullptr

  My question is a followup for the following: How to pin Eclipse to the Unity launcher? I created Eclipse's icon to the Unity launcher based on the selected answer at the above link. However, when I launch Eclipse via this icon, the environment variables are not properly set. I need to call . /opt/intel/bin/compilervars.sh intel64 to use Intel compiler tools in Eclipse. However, launching via the icon can't do it. Of course, running manually Eclipse on the terminal is okay. I tried to place . /opt/intel/bin/compilervars.sh intel64 on several places such as /etc/profile and /etc/bash.bashrc. But, still not working. Where is the best and correct place to call such environment setup?

  Read the article

• Representing and executing simple rules - framework or custom?

  - by qtips

  I am creating a system where users will be able to subscribe to events, and get notified when the event has occured. Example of events can be phone call durations and costs, phone data traffic notations, and even stock rate changes. Example of events: customer 13532 completed a call with duration 11:45 min and cost $0.4 stock rate for Google decreased with 0.01% Customers can subscribe to events using some simple rules e.g. When stock rate of Google decreases more than 0.5% When the cost of a call of my subscription is over $1 Now, as the set of different rules is currently predefined, I can easily create a custom implemention that applies rules to an event. But if the set of rules could be much larger, and if we also allow for custom rules (e.g. when stock rate of Google decreses more than 0.5% AND stock rate of Apple increases with 0.5%), the system should be able to adapt. I am therefore thinking of a system that can interpret rules using a simple grammer and then apply them. After som research I found that there exists rule-based engines that can be used, but I am unsure as they seem too complicated and may be a little overkill for my situation. Is there a Java framework suited for this area? Should we use framework, a rule engine, or should we create something custom? What are the pros and cons?

  Read the article

• Executing Components in an Entity Component System

  - by John

  Ok so I am just starting to grasp the whole ECS paradigm right now and I need clarification on a few things. For the record, I am trying to develop a game using C++ and OpenGL and I'm relatively new to game programming. First of all, lets say I have an Entity class which may have several components such as a MeshRenderer,Collider etc. From what I have read, I understand that each "system" carries out a specific task such as calculating physics and rendering and may use more that one component if needed. So for example, I would have a MeshRendererSystem act on all entities with a MeshRenderer component. Looking at Unity, I see that each Gameobject has, by default, got components such as a renderer, camera, collider and rigidbody etc. From what I understand, an entity should start out as an empty "container" and should be filled with components to create a certain type of game object. So what I dont understand is how the "system" works in an entity component system. http://docs.unity3d.com/ScriptReference/GameObject.html So I have a GameObject(The Entity) class like class GameObject { public: GameObject(std::string objectName); ~GameObject(void); Component AddComponent(std::string name); Component AddComponent(Component componentType); }; So if I had a GameObject to model a warship and I wanted to add a MeshRenderer component, I would do the following: warship->AddComponent(new MeshRenderer()); In the MeshRenderers constructor, should I call on the MeshRendererSystem and "subscribe" the warship object to this system? In that case, the MeshRendererSystem should probably be a Singleton("shudder"). From looking at unity's GameObject, if each object potentially has a renderer or any of the components in the default GameObject class, then Unity would iterate over all objects available. To me, this seems kind of unnecessary since some objects might not need to be rendered for example. How, in practice, should these systems be implemented?

  Read the article

• Executing Stored Procedures and Functions From PHP in Windows

  Discover how to call stored procedures and functions in MySQL from PHP using three database extensions: MySQL, MySQLi, and PDO.

  Read the article

• Executing NUnit Tests using the Visual Studio 2012 Test Runner

  - by David Paquette

  At a recent Visual Studio 2012 event at the Calgary .NET User Group, I was told that I could run my NUnit tests directly in the Visual Studio 2012 without any special plugins.  Naturally, I was very excited and I immediately tried running my NUnit tests. I was somewhat disappointed to see that the Test Runner did not discover any of my NUnit tests.  Apparently, you do still need to install an extension that supports NUnit.  Microsoft has completely re-written the Test Runner in Visual Studio 2012 and opened it up for anyone to write Test Adapters for any unit test framework (not just MSTest).  Once the correct test adapters are installed, everything works great.  Luckily, there are a good number of adapters already written. Here are some Test Adapters that you might find useful: NUnit Test Adapter – This one is still in beta, but tit does work with the official Visual Studio 2012 release xUnit.net Test Adapter Silverlight Unit Test Adapter Chutzpah Test Adapter Overall, I still prefer the unit test runner in ReSharper, but this is a great new feature for those who might not have a ReSharper license.

  Read the article

• After executing a command in the terminal, I sometimes can't execute another

  - by jreed121

  First off sorry for the noob question, I'm sure it's been asked before but I have no idea how to phrase it eloquently... Sometimes when I open/run/execute (unsure of proper term) an application (?lol) from the terminal like geany ie: geany filename.php or maybe run a node.js script: node server.js The command will execute fine, but I'm then left without the ability to execute any other commands unless I open another terminal. my root@pcname:~$ is gone and when I try typing in something else and hitting Enter it just breaks to the next line. I've noticed that sometimes I can hit CTRL+D and it'll give me my prompt back (sorry is prompt even the right name for it?) So could someone please explain why this is happening and how I can get back to the prompt without opening another terminal. Thanks, and sorry again for my noobery.

  Read the article

• executing .sh file from java program [migrated]

  - by user778900

  i have a .sh file stored in some linux system.the full path of the file is "/comviva/CPP/Kokila/TransactionHandler/scripts/stopTH.sh". i am tring to execute it by Runtime.getRuntime().exec("/comviva/CPP/Kokila/TransactionHandler/scripts/stopTH.sh"). but it is giving some exception. i want to execute that file from my java program in windows mechine. is it possible.?if yes then plese give me some code .. thanks koushik

  Read the article

• PHP NOT EXECUTING IN PHP-FPM AND NGINX INSTALLATION

  - by nairobicoder

  I am trying to set up nginx server to run a php app in debian. I followed this tutorial among others. Most seems the same. My recent configuration is based on the link above. When I try to run this php script, <?php phpinfo(); ?> I get the same output on the browser instead of php info result. Kindly someone help me figure out where I went wrong. Note: My error logs are clean,contains details on nginx server start only. Thank you.

  Read the article

• Rundeck get verbose output of command executing on node

  - by Leon Stafford

  I have Rundeck executing a remote script, which is in python is using print statements to return output normally such as: $ python mytest.py PASS: Condition 1 passed PASS: Condition 2 passed PASS: and so on... When I run this via Rundeck, however, it doesn't show me the same print generated outputs as above. In Rundeck's most detailed Debug output mode, I only receive the following: 06:31:12 Permanently added 'myremotenode.com' (RSA) to the list of known hosts. 06:31:12 SSH_MSG_NEWKEYS sent 06:31:12 SSH_MSG_NEWKEYS received 06:31:12 SSH_MSG_SERVICE_REQUEST sent 06:31:13 SSH_MSG_SERVICE_ACCEPT received 06:31:13 Authentications that can continue: publickey,password,keyboard-interactive 06:31:13 Next authentication method: publickey 06:31:13 Authentication succeeded (publickey). 06:31:13 /cygdrive/c/Program Files (x86)/Mozil... 06:32:06 Adding reference: ant.PropertyHelper 06:32:06 Setting project property: sshexec.output -> /cygdrive/c/Prog... I know that the remote script is actually executing just as usual, as I'm receiving other emails generated by the ~30min long script. Obviously, I don't want to have to wait 30mins to see the result of each print statement within the python script. How can I get the same level of output in Rundeck as I do in the bash shell directly?

  Read the article

• Executing batch file from sql server job

  - by uzay95

  I want to create backup job on sql server. And i want to execute batch file in job. I just wonder the part of executing batch file from sql job. Do you have any idea? Any help would appreciated. use MyDb go BACKUP DATABASE MyDb TO DISK = 'C:\BackUps\MyDb.bak' WITH differential go -- Call my batch file (which will zip MyDb.bak file)

  Read the article

• Executing batch file from sql server job

  - by uzay95

  I want to create backup job on sql server. And i want to execute batch file in job. I just wonder the part of executing batch file from sql job. Do you have any idea? Any help would appreciated. use MyDb go BACKUP DATABASE MyDb TO DISK = 'C:\BackUps\MyDb.bak' WITH differential go -- Call my batch file (which will zip MyDb.bak file)

  Read the article

• Executing git post-receive hook on windows server

  - by zulkamal

  I trying to execute a post-receive hook on a windows server git(msysgit) installation - to sync the repo to codebasehq. The script does nothing more than just wget "url" but it doesn't seem to be executing. I've renamed the "post-receive.sample" to "post-receive" and installed wget to windows path which works fine via the command prompt. Is there something I'm not doing here? I would appreciate any insights on how to get this working. Thanks.

  Read the article

• How can I resolve exception: Error executing child request for ChartImg.axd

  - by macleojw

  I'm using the Chart Controls for Mircosoft .NET Framerwork. Most of the time they work perfectly. However, if I leave a page for longer than 20-30 mins and then try to refresh the page, I get an error saying: Error executing child request for ChartImg.axd. Exception Details: System.Web.HttpException: Error executing child request for ChartImg.axd. If I update the page using an AJAX update panel I get the following error: Sys.WebForms.PageRequestManagerServerErrorException: Error executing child request for ChartImg.axd It seems that the chart handler stops after a period of inactivity. Most of the webpages I've looked at for this error are for situations when this error is displayed all the time. In my case it is only displayed after a period of inactivity. Can someone provide a better explanation of what is happening and suggest a solution?

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >