Search Results

Search found 10 results on 1 pages for 'fbm'.

Page 1/1 | 1 

• Can't connect to Wired Network after installing 12.04

  - by ezz9

  I have installed 12.04 into a used HP Compaq DC 7100 CMT. Plugged in LAN cable into the computer and it says network disconnected. from what I understand on the things I've read, it's not getting the address right, maybe it's just a guess (hardware address 00:16:35:78:47:bb). I know the LAN cable is working I can get on the net with the old computer. (Old computer is using device MAC address; Auto eth0 00:11:11:E6:4F:FE). I have put this address into the newer HP and it shows last used (minutes ago) but no Internet sever not found. I tried the hardware address it says never. I feel and think this should be easy to fix. But I just don't know. Here is the info everyone has asked for, but they never say what I should do. sudo lshw -C network; rfkill list; cat /etc/network/interfaces; cat /etc/lsb-release; lspci -nn; lsusb; uname -a; ifconfig; route -n *-network description: ethernet interface product; NetXtreme BCM5751 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:40:00.0 logical name: eth0 verson: 01 serial: 00:16:35:78:47:bb size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000-fd configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 duplex=full firmware=5751-v3.29a latency=0 link=yes multicast=yes port=twi sted pair speed=100Mbit/s resources: irq:17 memory:f0400000-f040ffff auto lo iface lo inet loopback DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION= "Ubuntu 12.04 LTS" 00:00.0 host bridge [0600]: Inter Corporation 82915G/P/GV/GL/PL/910GL Memory Con troller Hub [8086:2580] (rev 04) 00.02.0 VGA compatible controller [0300]: Intel Corporation 82915G/GV/910GL inte grated Graphics Controller [8086:2582] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 03) 00:1d.0 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #1 [8086:2658] (rev 03) 00:1d.1 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #2 [8086:2659] (rev 03) 00:1d.2 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #3 [8086:265a] (rev 03) 00:1d.3 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB UHCI #4 [8086:265b] (rev 03) 00:1d.7 USB controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Fam ily) USB2 UHCI Controller [8086:265c] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI bridge [8086:244e] (rev d 3) 00:1e.2 Multimedia audio controller [0401]: Intel Corporation 82801FB/FBM/FR/FW/ FRW (ICH6 Family) AC'97 Autio conrtroller [8086:266e] (rev 03) 00:1f.0 ISA bridge [0601]: Intel Corporation 82801FB/RF (ICH6/ICH6R) LPC Interfa ce Bridge [8086:2640] (rev 03) 00:1f.1 IDE interface [0101]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 fami ly) IDE Controller [8086:266f] (rev 03) 00:1f.2 IDE interface [0101]: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Con troller [8086:2651] (rev 03) 40:00.0 Ethernet controller [0200]: Broadcom Corporation NetXreme BCM5751 Gigab it Ethernet PCI Express [14e4:1677} (rev 01) Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Linux bob-desktop 3.2.0-23-generic-pae #36-Ubuntu SMP Tpr 10 22:19:09 UTC 20 12 i686 i686 i386 GNU/Linux eth0 Link encap:Ethernet HWaddr 00:16:35:78:47:bb inet6 addr: fe80::216:35ff:47bb/64 Scope:link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2517 errors:0 dropped:0 overruns:0 frame:0 TX packets:164 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164508 (164.5 KB) TX bytes: 40884 (40.0 KB) Interrupt:17 lo Link encap:Local loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3290 errors:0 dropped:0 overruns:0 frame:0 TX packets:3290 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen: 0 RX bytes:267212 (267.2 KB) TX bytes: 267212 (267.2 KB) Kernel Ip routing table Destination Gateway Genmask Flags Metric Ref Use Iface ran this sudo dhclient eth0 no reply ran this ip addr 1: lo <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST ,MULTICAST ,UP ,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000 link/enter 00:16:35:78:47:BB brd ff:ff:ff:ff:ff:ff inet 169.254.7.172/16 brd 169.254.255.255 scope link eth0:avahi inet6 fe80::216:35ff:fe78:47bb/64 scope link valid_lft forever preferred_lft forever Help please.

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• Sending File via peer mesh

  - by FBM

  can anybody help me or show some sample code in sending File on a peer mesh? I google it already but cannot find any sample how to do it. Thanks. FBM

  Read the article

• Disable time and date editing on Windows Mobile

  - by fbm

  Hi, Is there a way to disable time and date editing on a Windows Mobile device (via APIs or the registry)? I have an application using the time and date of a Windows Mobile PDA and I don't want the user to change it (the time and date) - unless - he/she has some kind of administrative rights. I haven't find a way to do it with the menus. Is it possible to do it in any other way? Thanks

  Read the article

• Long file path returning 404 for "hello.htm"

  - by Adam Kane

  Hello, I have a long file path that works on my server, but a simliar path returns a 404 error when it is on my clients (IIS6) server (http://ddmat.com/). Here's the functioning file path on my server: http://www.forgefx.com/projects/ddmat/install/Application Files/McCurdys_1_0_0_0/Content/FBX/CCAE1B33/Roof-sectionB-02.fbm/hello.htm My guesses: Maybe the file path is too long? Maybe the ".fbm" in the directory path is invalid? Sorry for the vauge problem description. Please let me know what additional info I can provide that'd be helpful. Update: The problem happens even in short paths, with no spaces: http://www.myserver/test.folder/hell.htm Thanks, Adam

  Read the article

• Dummy output after upgrade from 12.04 to 12.10, even though sound card is detected

  - by user115441

  So I just recently upgraded my system from Ubuntu 12.04 to 12.10. However, when I booted into 12.10 for the first time, no sound comes out of my speakers. I checked the sound settings and the Dummy Output was the only thing showing up. I used "hwinfo --sound" to check to see if my sound card was actually installed, and it was installed. hwinfo --sound hal.1: read hal dataprocess 2687: arguments to dbus_move_error() were incorrect, assertion "(dest) == NULL || !dbus_error_is_set ((dest))" failed in file ../../dbus/dbus-errors.c line 282. This is normally a bug in some application using the D-Bus library. libhal.c 3483 : Error unsubscribing to signals, error=The name org.freedesktop.Hal was not provided by any .service files 11: PCI 1b.0: 0403 Audio device [Created at pci.318] Unique ID: u1Nb._aiKlM91Nt0 SysFS ID: /devices/pci0000:00/0000:00:1b.0 SysFS BusID: 0000:00:1b.0 Hardware Class: sound Model: "Intel 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller" Vendor: pci 0x8086 "Intel Corporation" Device: pci 0x2668 "82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller" SubVendor: pci 0x107b "Gateway 2000" SubDevice: pci 0x4040 Revision: 0x04 Driver: "snd_hda_intel" Driver Modules: "snd_hda_intel" Memory Range: 0x50240000-0x50243fff (rw,non-prefetchable) IRQ: 44 (91 events) Module Alias: "pci:v00008086d00002668sv0000107Bsd00004040bc04sc03i00" Driver Info #0: Driver Status: snd_hda_intel is active Driver Activation Cmd: "modprobe snd_hda_intel" Config Status: cfg=new, avail=yes, need=no, active=unknown I'm not sure what to do here. The only time the sound will actually work is when I boot into my Windows partition and then reboot into Ubuntu. I mean I don't want to have to do that every time I want to use Ubuntu. I would really appreciate any help I can get on here.

  Read the article

• Disable time and date editing on Windows Mobile

  - by fbm

  Hi, Is there a way to disable time and date editing on a Windows Mobile device (via APIs or the registry)? I have an application using the time and date of a Windows Mobile PDA and I don't want the user to change it (the time and date) - unless - he/she has some kind of administrative rights. I haven't find a way to do it with the menus. Is it possible to do it in any other way? Thanks

  Read the article

• Audio not working in 12.10

  - by frampy

  I did a clean install of 12.10, when I open Sound Settings in gnome the only device in the list is "Dummy Output", and sound is not working. Sound worked fine out of the box in 12.04 I ran alsamixer, it says my card is "HDA Intel", and chip is "Realtek ALC880". The alsamixer playback output was set to mute at first, unmuting did not fix. I checked out the info at http://www.unixmen.com/2012003-howto-resolve-nosound-problem-on-ubuntu/ as suggested on a similar question, I've done everything there except installing the ubuntu audio dev team driver. Should I try install this? Edit: I've been reading the sound troubleshooting guide at https://help.ubuntu.com/community/SoundTroubleshooting It looks like Ubuntu is finding my audio device correctly. mike@wucade:~$ lspci -v | grep -A7 -i "audio" 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Albatron Corp. Device 2668 Flags: bus master, fast devsel, latency 0, IRQ 40 Memory at d01c0000 (64-bit, non-prefetchable) [size=16K] Capabilities: Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel Still stuck as to why this isn't working.

  Read the article

• No audio in my ubuntu system

  - by hap497

  Hi, I am running ubuntu 9.10. But there is no sound in my environment. When I go to System-Preference, there is no 'sound' entry there. $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: I82801AAICH [Intel 82801AA-ICH], device 0: Intel ICH [Intel 82801AA-ICH] Subdevices: 1/1 Subdevice #0: subdevice #0 $ lsmod Module Size Used by usb_storage 52576 3 binfmt_misc 8356 1 vboxvfs 34620 0 vboxvideo 1884 1 drm 159584 2 vboxvideo agpgart 34988 1 drm snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 snd_seq_oss 28576 0 iptable_filter 3100 0 snd_seq_midi 6432 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi ppdev 6688 0 snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_mid i_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi ,snd_seq psmouse 56500 0 serio_raw 5280 0 snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_ oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_ti mer,snd_seq_device i2c_piix4 9932 0 parport_pc 31940 0 soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm vboxguest 143836 7 vboxvfs lp 8964 0 parport 35340 3 ppdev,parport_pc,lp pcnet32 32644 0 mii 5212 1 pcnet32 floppy 54916 0 ~:987:2$ lspci 00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC [Natoma] (rev 02) 00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] 00:01.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter 00:03.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 40) 00:04.0 System peripheral: InnoTek Systemberatung GmbH VirtualBox Guest Service 00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (rev 01) 00:06.0 USB Controller: Apple Computer Inc. KeyLargo/Intrepid USB 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 0 00:0b.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller ~:988:3$

  Read the article

• Hearing a clicking noise from soundcard all the time

  - by Mehrdad

  I have installed Fedora 17 on my laptop. A few days ago I updated my fedora (but not upgraded). I shut down my computer and since the next time I turned it on I am hearing a clicking noise all the time from speakers. Even when I plug my headphones in I hear the noise through the headphone. I surfed over the internet and found the following shell commands: su -c 'echo "options snd_hda_intel power_save=0" /etc/modprobe.d/snd_hda_intel.conf' su -c 'echo 0 /sys/module/snd_hda_intel/parameters/power_save' I tried them but they didn't work. Here is the part of "lspci" command related to my sound-card: 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) I have to add that my sound-card is working and I can play some audio file, I mean I can hear the voice and noise simultaneously. But everything is OK in windows xp which is also installed on my laptop. Could it be related to the sound-card driver? If so, how can I revert it to the previous version?

  Read the article

1