Search Results

Search found 8 results on 1 pages for 'jetboy'.

Page 1/1 | 1 

• Using a Dell DRAC virtual console through a NAT firewall

  - by jetboy

  I have two Dell Poweredge R210 servers, both running Ubuntu 10 Server x64. Server A has a Dell DRAC ILO card (on 172.16.96.91), and both the server and the DRAC use Server B as a gateway (with server B's WAN IP being xxx.xxx.xxx.xx). Server B uses the following NAT rules in IPTables to route traffic through to Server A's DRAC: *NAT --append PREROUTING --in-interface eth1 --protocol tcp --destination xxx.xxx.xxx.xx --destination-port 8019 --jump DNAT --to-destination 172.16.96.91:443 --append POSTROUTING --out-interface eth1 --jump SNAT --to-source xxx.xxx.xxx.xx This works fine for accessing Server A's DRAC via Server B, apart from the Java virtual console. This fails with the following error: com.sun.deploy.net.FailedDownloadException: Unable to load resource: https://xxx.xxx.xxx.xx:443/software/avctKVM.jar at com.sun.deploy.net.DownloadEngine.actionDownload(Unknown Source) etc. I know that the Java console uses port 5900, and possibly ports 83 and 5891. Can anyone help me in getting this working?

  Read the article

• Isolating VMware virtual machines from the network

  - by jetboy

  I have: VMware Workstation 7 running on a Windows 7 box (with a single NIC), with multiple virtual machines running a range of OSs. The host box is connected to a WRT54G router running Tomato firmware. The router is acting as a wireless bridge to another WRT54G that's wired to my broadband modem. I can access the VMs externally via VNC using VMware's Remote Display. Over time I've had these running: a. Using NAT networking (single IP) with port forwarding on the router and a custom port in VMware for each VM. b. Using bridged networking with static IPs assigned to each VM via MAC address, and port forwarding on the router to each IP running with standard ports. Either way, the host box, and other physical machines on the network are accessible from the VMs. Is there a way to isolate the VMs from the rest of the network, but still maintain internet access and remote VNC to the VMs?

  Read the article

• RAID options for a LAMP web server

  - by jetboy

  I'm due to set up a LAMP web server with four drives and a RAID controller to act as a web server. The drives are 146Gb SAS, and the machine has two quad core processors and 16Gb RAM. There will be very few write operations to the MySQL database, and I'll be using as much caching as possible to reduce disk I/O. Question is: Would I be better off splitting the drives into two RAID 1 arrays, splitting up sequential and random disk I/O, or would I get better overall performance putting them all in a single RAID 1+0 array?

  Read the article

• Has anyone managed to build php5-xapian on Ubuntu 12.04?

  - by jetboy

  As Xapian's been dropped from the Ubuntu repositories, I'm attempting to build my own .deb from the instructions here: http://article.gmane.org/gmane.comp.search.xapian.general/8855 http://beeznest.wordpress.com/2011/07/06/howto-build-your-own-binaries-of-php-xapian-bindings-for-debian/ I can only get things to progress beyond the first few seconds by leaving out 'rm debian/control', but if I do, it looks as if the Python and Ruby bindings are building and passing their versions of smoketest correctly. However, the PHP part of the build is failing with this error: /home/charlie/xapian-bindings-1.2.8/php/smoketest.php:38: include(xapian.php): failed to open stream: No such file or directory FAIL: smoketest.php There's a xapian.php file in /home/charlie/xapian-bindings-1.2.8/php/php5/ but if I copy it to /home/charlie/xapian-bindings-1.2.8/php/ or change the path to it in smoketest.php, the build fails right near the start with: dpkg-source: error: aborting due to unexpected upstream changes Unfortunately I'm out of my comfort zone building from source. Anyone got any ideas? Edit post James' answer: Builds fine if I follow instructions exactly. I built it on a test VM initially, but that didn't build the PHP package as PHP itself wasn't installed. Obvious gotcha, but worth mentioning. Installing generated the following error: Setting up php5-xapian (1.2.8-1) ... Processing triggers for libapache2-mod-php5 ... dpkg (subprocess): unable to execute installed post-installation script (/var/lib/dpkg/info/libapache2-mod-php5.postinst): Permission denied ssion denied dpkg: error processing libapache2-mod-php5 (--install): subprocess installed post-installation script returned error exit status 2 Errors were encountered while processing: libapache2-mod-php5 It's only a script for restarting Apache. Stopping Apache before running sudo dpkg -i php5-xapian_*.deb prevents the error. Xapian now shows up in phpinfo(). Job done. Thanks.

  Read the article

• Syntax for piping varnish logs to rotatelogs

  - by jetboy

  Ubuntu 12.04 Server x64, Varnish 3.0.2 I'm trying to pipe varnishncsa's logs through Apache's rotatelogs, and running from the shell, things work fine: sudo varnishncsa -a -P /var/run/varnishncsa/varnishncsa.pid |/usr/sbin/rotatelogs /var/log/varnish/varnish.log.%Y%m%d%H 3600 creates a new logfile in /var/log/varnish, with rotation every hour (3600 seconds). However, I'm struggling to get things working the same way inside /etc/init.d/varnishncsa: PATH=/sbin:/bin:/usr/sbin:/usr/bin DAEMON=/usr/bin/$NAME PIDFILE=/var/run/$NAME/$NAME.pid LOGFILE=/var/log/varnish/varnishncsa.log USER=varnishlog DAEMON_OPTS="-a -P ${PIDFILE}" DAEMON_PIPE="|/usr/sbin/rotatelogs /var/log/varnish/varnish.log.%Y%m%d%H 3600" ... start_varnishncsa() { output=$(/bin/tempfile -s.varnish) log_daemon_msg "Starting $DESC" "$NAME" create_pid_directory if start-stop-daemon --start --verbose --pidfile ${PIDFILE} \ --chuid $USER --exec ${DAEMON} -- ${DAEMON_OPTS} \ > ${output} 2>&1; then log_end_msg 0 else log_end_msg 1 cat $output exit 1 fi rm $output } Where should I put DAEMON_PIPE in the above code? I've tried at the end of: if start-stop-daemon --start --verbose --pidfile ${PIDFILE} which is where additional command line parameters usually go, but it isn't creating a logfile.

  Read the article

• sudoers security

  - by jetboy

  I've setup a script to do Subversion updates across two servers - the localhost and a remote server - called by a post-commit hook run by the www-data user. /srv/svn/mysite/hooks/post-commit contains: sudo -u cli /usr/local/bin/svn_deploy /usr/local/bin/svn_deploy is owned by the cli user, and contains: #!/bin/sh svn update /srv/www/mysite ssh cli@remotehost 'svn update /srv/www/mysite' To get this to work I've had to add the following to the sudoers file: www-data ALL = (cli) NOPASSWD: /usr/local/bin/svn_deploy cli ALL = NOEXEC:NOPASSWD: /usr/local/bin/svn_deploy Entries for both www-data and cli were necessary to avoid the error: post commit hook failed: no tty present and no askpass program specified I'm wary of giving any kind of elevated rights to www-data. Is there anything else I should be doing to reduce or eliminate any security risk?

  Read the article

• Logging the client IP with Nginx/Varnish/Apache

  - by jetboy

  I have Nginx listening on port 443 as an SSL terminator, and proxying unencrypted traffic to Varnish on the same server. Varnish 3 is handling this traffic, and traffic coming in directly on port 80. All traffic is passed, unencrypted, to Apache instances on other servers in the cluster. The Apache instances use mod_rpaf to replace the logged client IP with the contents of the X-Forwarded-For header. My problem is that if the traffic is coming via Nginx, while the 'correct' client IP is getting logged in the VarnishNCSA logs, it looks as if Varnish is (understandably) replacing Nginx's X-Forwarded-For header with 127.0.0.1 downstream, and this is getting logged with Apache. Is there a nice simple way to stop Varnish rewriting X-Forwarded-For if it's already populated?

  Read the article

• Adding View extending from SurfaceView to layout gives me a blank screen

  - by JonF

  I'm very new to Android programming, so this is probably something pretty basic. I just have an xml layout with a few buttons. I'm trying to follow the model given by the JetBoy demo, so I'm adding a view to the layout which extends SurfaceView. When this new view is put in my xml layout, I just get a blank screen. Here's the XML layout if it helps. The gameview element is what causes the screen to be blank <?xml version="1.0" encoding="utf-8"?> <LinearLayout xmlns:android="http://schemas.android.com/apk/res/android" android:orientation="vertical" android:layout_width="fill_parent" android:layout_height="fill_parent" android:alwaysDrawnWithCache="true"> <game.test.gameEngine android:id="@+id/gameView" android:layout_width="fill_parent" android:layout_height="fill_parent"/> <Button android:text="Easy" android:layout_width="wrap_content" android:layout_height="wrap_content" android:id="@+id/EasyButton"></Button> <Button android:text="Medium" android:layout_width="wrap_content" android:layout_height="wrap_content" android:id="@+id/MedButton"></Button> <Button android:text="Hard" android:layout_width="wrap_content" android:layout_height="wrap_content" android:id="@+id/HardButton"></Button> <DatePicker android:id="@+id/DatePicker01" android:layout_width="wrap_content" android:layout_height="wrap_content"></DatePicker><Button android:id="@+id/Button04" android:layout_width="wrap_content" android:layout_height="wrap_content" android:text="Exit"></Button> </LinearLayout>

  Read the article

1