Search Results

Search found 52 results on 3 pages for 'joker vd'.

Page 1/3 | 1 2 3  | Next Page >

• Problems with 5.1 digital out on Ubuntu 12.04

  - by user895319

  I've recently bought a new PC, installed Ubuntu and am now unable to get 5.1 digital sound working. Simple analogue stereo works fine on both the front and rear connectors. On my old box I connected the coax connection from my soundcard to my surround sound amplifier, set Settings-Sound to "Digital Stereo Duplex" and it worked. My old soundcard doesn't fit in my new machine so I'm using the built-in sound hardware. I'm connecting the combination output socket on the back of the PC via the same cable to my surround amp as before. The MB is an MSI Global H61M-P31 with an RealTek ALC887 sound chip. When I go to Settings-Sound I only see "Headphone Built-in Audio" and "Analogue Output Built-in Audio" - no digitial options. The output from aplay -l is: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC887-VD Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Hardware device with all software conversions While googling for ALC887 I've seen some references to "ALC887 -VD Analog" and some to "ALC887 -VD Digital". Does anyone know if I need to force it to chance mode somehow? It's worth mentioning that when I set the output to 5.1 digital surround in Windows 7 on the same machine I still don't get any sound so it's not a unique Linux problem. Thanks for any help.

  Read the article

• what architecture to use with asp.net mvc vd web forms

  - by kacalapy

  please explain how to get high capacity architectures with both the default asp.net web forms and mvc models with regard to being able to serve millions of page views. i want to know how to set up each model from DB clustering, to caching, logical/ physical tiers, load balancing iis servers, scaling out or up, session state management and so on... is one more scalable than the other? thanks all.

  Read the article

• BlackBerry 10 sera lancé le 30 janvier 2013, le joker de RIM sortira avec deux modèles de smartphones

  BlackBerry 10 en test auprès de 50 opérateurs dans le monde l'OS mobile franchit un cap crucial le rapprochant de son lancement début 2013 Même si la date de sortie officielle de BlackBerry 10 n'est pas encore connue, l'OS a franchi un cap crucial dans son cycle de développement, le rapprochant de sa période de lancement. Thorsten Heins, le PDG de RIM a annoncé que l'OS mobile a été mis à la disposition de 50 opérateurs à travers le monde afin que ceux-ci puissent procéder à des tests. Cette étape importante pour le PDG du constructeur canadien signifie que la firme pourra tenir son engagement de lancer BlackBerry 10 durant le premier trimestre de l'année prochaine. ...

  Read the article

• Problem with ebay AddItem API call [migrated]

  - by user1323572

  I am totally new to any sort of API application. Right now I am creating a listing application to list items on E-bay India site. API version being used is 767, sandbox url is https://api.sandbox.ebay.com/wsapi. I have sandbox account for ebay(buyer/seller) and developer account. I am getting error saying: 1) Sales Tax / VAT was dropped from the listing as per new sales tax / VAT policy. The items will be listed successfully, you may revise the listing to specify all inclusive price. 2) You have either not registered or are having problem with your payment method registration. ItemType type = new ItemType(); type.PaymentMethods = new BuyerPaymentMethodCodeTypeCollection(); type.PaymentMethods.Add(BuyerPaymentMethodCodeType.PaisaPayAccepted); Also do I have to specify taxation for each state? For VAT and shipping details here's my snippet: private ShippingDetailsType getShippingDetails() { // Shipping details. ShippingDetailsType sd = new ShippingDetailsType(); SalesTaxType salesTax = new SalesTaxType(); ReadSettings rs = new ReadSettings(); rs.GetSettings(); salesTax.SalesTaxPercent = 12f; salesTax.SalesTaxState = "MH"; SalesTaxType s = new SalesTaxType(); salesTax.ShippingIncludedInTax = true; salesTax.ShippingIncludedInTaxSpecified = true; sd.ApplyShippingDiscount = true; AmountType at = new AmountType(); at.Value = 2.8; at.currencyID = CurrencyCodeType.INR; sd.InsuranceFee = at; sd.InsuranceOption = InsuranceOptionCodeType.NotOffered; sd.PaymentInstructions = "These are my instructions."; VATDetailsType vd = new VATDetailsType(); vd.BusinessSeller = false; vd.BusinessSellerSpecified = false; vd.RestrictedToBusiness = false; vd.RestrictedToBusinessSpecified = false; vd.VATID = "VATSNO1234567890"; vd.VATPercent = 12f; vd.VATPercentSpecified = true; vd.VATSite = "None"; sd.ShippingType = ShippingTypeCodeType.Flat; // ShippingServiceOptionsType st1 = new ShippingServiceOptionsType(); sd.SalesTax = salesTax; st1.ShippingService = ShippingServiceCodeType.IN_Express.ToString(); at = new AmountType(); at.Value = 50; at.currencyID = CurrencyCodeType.INR; st1.ShippingServiceAdditionalCost = at; at = new AmountType(); at.Value = 50; at.currencyID = CurrencyCodeType.INR; st1.ShippingServiceCost = at; st1.ShippingServicePriority = 1; at = new AmountType(); at.Value = 1.0; at.currencyID = CurrencyCodeType.INR; st1.ShippingInsuranceCost = at; sd.ShippingServiceOptions = new ShippingServiceOptionsTypeCollection(new ShippingServiceOptionsType[] { st1 }); return sd; } Thank you for you efforts.

  Read the article

• Is There Anyway to Undo a Quick Initialize from a Perc6/i VD?

  - by Carlo71

  I stupidly fast initialized an existing Raid 5 Array Virtual disk with 10 Virtual Machines after creating a new Raid 5 Array. The VDs switched order on the list of the Perc Controller. My server is a PowerEdge R710 with a Perc 6/i Raid controller running ESXi 5.1. The Bios of the R710 and the Perc 6/i controller are both running the latest firmware. I tried the steps on this article: http://www.caseyfulton.com/dell-perc-6i-fast-initialize-how-to-restore/. However the BartPE just freezes on the Windows XP slapsh page. Does anybody know a full proof method? I have backups of the VMs, however I would like to avoid restoring all of them due to time constraint.

  Read the article

• No rear audio when front jack is connected

  - by Shanoop

  I have Ubuntu 14.04 64bit dual booted. When I connect something on front audio jack then rear audio is not working. I have tried changing analolog-output-headphones.conf file. After changing that alsamixer showing that both centre and surround not muted with full volum. Unfortunately no audio. aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SB [HDA ATI SB], device 0: ALC887-VD Analog [ALC887-VD Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: SB [HDA ATI SB], device 1: ALC887-VD Digital [ALC887-VD Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 7: HDMI 1 [HDMI 1] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: NVidia [HDA NVidia], device 8: HDMI 2 [HDMI 2] Subdevices: 1/1 Subdevice #0: subdevice #0

  Read the article

• How to use CASE in SQL , Syntax Error being shown

  - by Shantanu Gupta

  I am trying to retrieve some records from table based on my query but it shows me an error Msg 102, Level 15, State 1, Line 2 Incorrect syntax near ' select vd.LedgerId,(CreditAmt-DebitAmt) AS NET, CASE NET WHEN NET > 0 THEN 'Debit' WHEN NET < 0 THEN 'Credit' ELSE 'Nil'End from dbo.vdebit vd INNER JOIN dbo.vCredit vc ON vd.LedgerId=vc.LedgerId

  Read the article

• BoundingBox created from mesh to origin, making it bigger

  - by Gunnar Södergren

  I'm working on a level-based survival game and I want to design my scenes in Maya and export them as a single model (with multiple meshes) into XNA. My problem is that when I try to create Bounding Boxes(for Collision purposes) for each of the meshes, the are calculated from origin to the far-end of the current mesh, so to speak. I'm thinking that it might have something to do with the position each mesh brings from Maya and that it's interpreted wrongly... or something. Here's the code for when I create the boxes: private static BoundingBox CreateBoundingBox(Model model, ModelMesh mesh) { Matrix[] boneTransforms = new Matrix[model.Bones.Count]; model.CopyAbsoluteBoneTransformsTo(boneTransforms); BoundingBox result = new BoundingBox(); foreach (ModelMeshPart meshPart in mesh.MeshParts) { BoundingBox? meshPartBoundingBox = GetBoundingBox(meshPart, boneTransforms[mesh.ParentBone.Index]); if (meshPartBoundingBox != null) result = BoundingBox.CreateMerged(result, meshPartBoundingBox.Value); } result = new BoundingBox(result.Min, result.Max); return result; } private static BoundingBox? GetBoundingBox(ModelMeshPart meshPart, Matrix transform) { if (meshPart.VertexBuffer == null) return null; Vector3[] positions = VertexElementExtractor.GetVertexElement(meshPart, VertexElementUsage.Position); if (positions == null) return null; Vector3[] transformedPositions = new Vector3[positions.Length]; Vector3.Transform(positions, ref transform, transformedPositions); for (int i = 0; i < transformedPositions.Length; i++) { Console.WriteLine(" " + transformedPositions[i]); } return BoundingBox.CreateFromPoints(transformedPositions); } public static class VertexElementExtractor { public static Vector3[] GetVertexElement(ModelMeshPart meshPart, VertexElementUsage usage) { VertexDeclaration vd = meshPart.VertexBuffer.VertexDeclaration; VertexElement[] elements = vd.GetVertexElements(); Func<VertexElement, bool> elementPredicate = ve => ve.VertexElementUsage == usage && ve.VertexElementFormat == VertexElementFormat.Vector3; if (!elements.Any(elementPredicate)) return null; VertexElement element = elements.First(elementPredicate); Vector3[] vertexData = new Vector3[meshPart.NumVertices]; meshPart.VertexBuffer.GetData((meshPart.VertexOffset * vd.VertexStride) + element.Offset, vertexData, 0, vertexData.Length, vd.VertexStride); return vertexData; } } Here's a link to the picture of the mesh(The model holds six meshes, but I'm only rendering one and it's bounding box to make it clearer: http://www.gsodergren.se/portfolio/wp-content/uploads/2011/10/Screen-shot-2011-10-24-at-1.16.37-AM.png The mesh that I'm refering to is the Cubelike one. The cylinder is a completely different model and not part of any bounding box calculation. I've double- (and tripple-)-checked that this mesh corresponds to this bounding box. Any thoughts on what I'm doing wrong?

  Read the article

• How to define AUTHPARAMS in Amazon EC2 API call

  - by The Joker

  I am trying to make an API call to EC2. I want to add my IP address to the security group. https://ec2.amazonaws.com/ ?Action=AuthorizeSecurityGroupIngress &GroupName=grppp20 &GroupId=sg-b2z982mq &IpPermissions.1.IpProtocol=tcp &IpPermissions.1.FromPort=3389 &IpPermissions.1.ToPort=3389 &IpPermissions.1.IpRanges.1.CidrIp=22.951.17.728/32 &&AWSAccessKeyId=AOPLDRACULALK6U7A And i get the following error. AWS was not able to validate the provided access credentials I have a secret access key & a username. I searched internet & found that we have to make a signature of the secret key & use it in the request instead of adding it directly. Can anyone tell me how to make a signature of my AWS secret key & how to use them with my API call? Let my secret key be: 2WwRiQzBs7RTFG4545PIOJ7812CXZ Username: thejoker

  Read the article

• Mocking HtmlHelper throws NullReferenceException

  - by Matt Austin

  I know that there are a few questions on StackOverflow on this topic but I haven't been able to get any of the suggestions to work for me. I've been banging my head against this for two days now so its time to ask for help... The following code snippit is a simplified unit test to demonstrate what I'm trying to do, which is basically call RadioButtonFor in the Microsoft.Web.Mvc assembly in a unit test. var model = new SendMessageModel { SendMessageType = SendMessageType.Member }; var vd = new ViewDataDictionary(model); vd.TemplateInfo = new TemplateInfo { HtmlFieldPrefix = string.Empty }; var controllerContext = new ControllerContext(new Mock<HttpContextBase>().Object, new RouteData(), new Mock<ControllerBase>().Object); var viewContext = new Mock<ViewContext>(new object[] { controllerContext, new Mock<IView>().Object, vd, new TempDataDictionary(), new Mock<TextWriter>().Object }); viewContext.Setup(v => v.View).Returns(new Mock<IView>().Object); viewContext.Setup(v => v.ViewData).Returns(vd).Callback(() => {throw new Exception("ViewData extracted");}); viewContext.Setup(v => v.TempData).Returns(new TempDataDictionary()); viewContext.Setup(v => v.Writer).Returns(new Mock<TextWriter>().Object); viewContext.Setup(v => v.RouteData).Returns(new RouteData()); viewContext.Setup(v => v.HttpContext).Returns(new Mock<HttpContextBase>().Object); viewContext.Setup(v => v.Controller).Returns(new Mock<ControllerBase>().Object); viewContext.Setup(v => v.FormContext).Returns(new FormContext()); var mockContainer = new Mock<IViewDataContainer>(); mockContainer.Setup(x => x.ViewData).Returns(vd); var helper = new HtmlHelper<ISendMessageModel>(viewContext.Object, mockContainer.Object, new RouteCollection()); helper.RadioButtonFor(m => m.SendMessageType, "Member", cssClass: "selector"); If I remove the cssClass parameter then the code works ok but fails consistently when adding additional parameters. I've tried every combination of mocking, instantiating concrete types and using fakes that I can think off but I always get a NullReferenceException when I call RadioButtonFor. Any help hugely appreciated!!

  Read the article

• LSI 9285-8e and Supermicro SC837E26-RJBOD1 duplicate enclosure ID and slot numbers

  - by Andy Shinn

  I am working with 2 x Supermicro SC837E26-RJBOD1 chassis connected to a single LSI 9285-8e card in a Supermicro 1U host. There are 28 drives in each chassis for a total of 56 drives in 28 RAID1 mirrors. The problem I am running in to is that there are duplicate slots for the 2 chassis (the slots list twice and only go from 0 to 27). All the drives also show the same enclosure ID (ID 36). However, MegaCLI -encinfo lists the 2 enclosures correctly (ID 36 and ID 65). My question is, why would this happen? Is there an option I am missing to use 2 enclosures effectively? This is blocking me rebuilding a drive that failed in slot 11 since I can only specify enclosure and slot as parameters to replace a drive. When I do this, it picks the wrong slot 11 (device ID 46 instead of device ID 19). Adapter #1 is the LSI 9285-8e, adapter #0 (which I removed due to space limitations) is the onboard LSI. Adapter information: Adapter #1 ============================================================================== Versions ================ Product Name : LSI MegaRAID SAS 9285-8e Serial No : SV12704804 FW Package Build: 23.1.1-0004 Mfg. Data ================ Mfg. Date : 06/30/11 Rework Date : 00/00/00 Revision No : 00A Battery FRU : N/A Image Versions in Flash: ================ BIOS Version : 5.25.00_4.11.05.00_0x05040000 WebBIOS Version : 6.1-20-e_20-Rel Preboot CLI Version: 05.01-04:#%00001 FW Version : 3.140.15-1320 NVDATA Version : 2.1106.03-0051 Boot Block Version : 2.04.00.00-0001 BOOT Version : 06.253.57.219 Pending Images in Flash ================ None PCI Info ================ Vendor Id : 1000 Device Id : 005b SubVendorId : 1000 SubDeviceId : 9285 Host Interface : PCIE ChipRevision : B0 Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 5003048000ee8e7f 1 5003048000ee8a7f 2 0000000000000000 3 0000000000000000 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 500605b0038f9210 BBU : Present Alarm : Present NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 1024MB TPM : Absent On board Expander: Absent Upgrade Key : Absent Temperature sensor for ROC : Present Temperature sensor for controller : Absent ROC temperature : 70 degree Celcius Settings ================ Current Time : 18:24:36 3/13, 2012 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : Disabled Cluster Mode : Disabled Alarm : Enabled Auto Rebuild : Enabled Battery Warning : Enabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Enabled Maintain PD Fail History : Enabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 10 Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Mix of SAS/SATA of HDD type in VD Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 60 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Max LD per array : 16 Min Strip Size : 8 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 887 MB Device Present ================ Virtual Drives : 28 Degraded : 0 Offline : 0 Physical Devices : 59 Disks : 56 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : No Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Snapshot Enabled : No Support the OCE without adding drives : Yes Support PFK : Yes Support PI : No Support Boot Time PFK Change : Yes Disable Online PFK Change : No PFK TrailTime Remaining : 0 days 0 hours Support Shield State : Yes Block SSD Write Disk Cache Change: Yes Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : No Support Breakmirror : No Power Savings : Yes Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : Yes Disable Copyback : No Enable JBOD : No Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : Yes Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Enable Spin Down of UnConfigured Drives : Yes Disable Spin Down of hot spares : No Spin Down time : 30 T10 Power State : Yes Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : Adaptive Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : Yes Coercion Mode : None ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : No Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : Yes Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 16 Disable Ctrl-R : Yes Enable Web BIOS : Yes Direct PD Mapping : No BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : Yes Maintain PD Fail History : Yes Disable Puncturing : No Zero Based Enclosure Enumeration : No PreBoot CLI Enabled : Yes LED Show Drive Activity : Yes Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 EnableCrashDump : No Disable Online Controller Reset : No EnableLDBBM : No Un-Certified Hard Disk Drives : Allow Treat Single span R1E as R10 : No Max LD per array : 16 Power Saving option : Don't Auto spin down Configured Drives Max power savings option is not allowed for LDs. Only T10 power conditions are to be used. Default spin down time in minutes: 30 Enable JBOD : No TTY Log In Flash : No Auto Enhanced Import : No BreakMirror RAID Support : No Disable Join Mirror : No Enable Shield State : Yes Time taken to detect CME : 60s Exit Code: 0x00 Enclosure information: # /opt/MegaRAID/MegaCli/MegaCli64 -encinfo -a1 Number of enclosures on adapter 1 -- 3 Enclosure 0: Device ID : 36 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port B Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 65 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11820 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 48 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 1: Device ID : 65 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port A Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 36 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11760 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 47 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 2: Device ID : 252 Number of Slots : 8 Number of Power Supplies : 0 Number of Fans : 0 Number of Temperature Sensors : 0 Number of Alarms : 0 Number of SIM Modules : 1 Number of Physical Drives : 0 Status : Normal Position : 1 Connector Name : Unavailable Enclosure type : SGPIO Failed in first Inquiry commnad FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : Unavailable Inquiry data : Vendor Identification : LSI Product Identification : SGPIO Product Revision Level : N/A Vendor Specific : Exit Code: 0x00 Now, notice that each slot 11 device shows an enclosure ID of 36, I think this is where the discrepancy happens. One should be 36. But the other should be on enclosure 65. Drives in slot 11: Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 5, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 48 WWN: Sequence Number: 11 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : YES Device Firmware Level: A5C0 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8a53 Connected Port Number: 1(path0) Inquiry Data: MJ1311YNG6YYXAHitachi HDS5C3030ALA630 MEAOA5C0 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 19, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 19 WWN: Sequence Number: 4 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : NO Device Firmware Level: A580 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8e53 Connected Port Number: 0(path0) Inquiry Data: MJ1313YNG1VA5CHitachi HDS5C3030ALA630 MEAOA580 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Update 06/28/12: I finally have some new information about (what we think) the root cause of this problem so I thought I would share. After getting in contact with a very knowledgeable Supermicro tech, they provided us with a tool called Xflash (doesn't appear to be readily available on their FTP). When we gathered some information using this utility, my colleague found something very strange: root@mogile2 test]# ./xflash.dat -i get avail Initializing Interface. Expander: SAS2X36 (SAS2x36) 1) SAS2X36 (SAS2x36) (50030480:00EE917F) (0.0.0.0) 2) SAS2X36 (SAS2x36) (50030480:00E9D67F) (0.0.0.0) 3) SAS2X36 (SAS2x36) (50030480:0112D97F) (0.0.0.0) This lists the connected enclosures. You see the 3 connected (we have since added a 3rd and a 4th which is not yet showing up) with their respective SAS address / WWN (50030480:00EE917F). Now we can use this address to get information on the individual enclosures: [root@mogile2 test]# ./xflash.dat -i 5003048000EE917F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00EE917F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 5003048000E9D67F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00E9D67F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 500304800112D97F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:0112D97F Enclosure Logical Id: 50030480:0112D97F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 Did you catch it? The first 2 enclosures logical ID is partially masked out where the 3rd one (which has a correct unique enclosure ID) is not. We pointed this out to Supermicro and were able to confirm that this address is supposed to be set during manufacturing and there was a problem with a certain batch of these enclosures where the logical ID was not set. We believe that the RAID controller is determining the ID based on the logical ID and since our first 2 enclosures have the same logical ID, they get the same enclosure ID. We also confirmed that 0000007F is the default which comes from LSI as an ID. The next pointer that helps confirm this could be a manufacturing problem with a run of JBODs is the fact that all 6 of the enclosures that have this problem begin with 00E. I believe that between 00E8 and 00EE Supermicro forgot to program the logical IDs correctly and neglected to recall or fix the problem post production. Fortunately for us, there is a tool to manage the WWN and logical ID of the devices from Supermicro: ftp://ftp.supermicro.com/utility/ExpanderXtools_Lite/. Our next step is to schedule a shutdown of these JBODs (after data migration) and reprogram the logical ID and see if it solves the problem. Update 06/28/12 #2: I just discovered this FAQ at Supermicro while Google searching for "lsi 0000007f": http://www.supermicro.com/support/faqs/faq.cfm?faq=11805. I still don't understand why, in the last several times we contacted Supermicro, they would have never directed us to this article :\

  Read the article

• Change the Default Application Pool in IIS7 using .net?

  - by EdenMachine

  I'm using the following function to create a IIS7 Application and/or Virtual Directory. How would I also set the Application to use a different Application Pool? Private Sub CreateVirtualDir(ByVal WebSite As String, ByVal AppName As String, ByVal Path As String, Optional ByVal IsApplication As Boolean = True, Optional ByVal RunScripts As Boolean = True, Optional ByVal IsWrite As Boolean = True) Dim IISSchema As New System.DirectoryServices.DirectoryEntry("IIS://" & WebSite & "/Schema/AppIsolated") Dim CanCreate As Boolean = Not IISSchema.Properties("Syntax").Value.ToString.ToUpper() = "BOOLEAN" IISSchema.Dispose() If CanCreate Then Dim PathCreated As Boolean Try Dim IISAdmin As New System.DirectoryServices.DirectoryEntry("IIS://" & WebSite & "/W3SVC/1/Root") 'make sure folder exists If Not System.IO.Directory.Exists(Path) Then System.IO.Directory.CreateDirectory(Path) PathCreated = True End If 'If the virtual directory already exists then delete it For Each VD As System.DirectoryServices.DirectoryEntry In IISAdmin.Children If VD.Name = AppName Then IISAdmin.Invoke("Delete", New String() {VD.SchemaClassName, AppName}) IISAdmin.CommitChanges() Exit For End If Next VD 'Create and setup new virtual directory Dim VDir As System.DirectoryServices.DirectoryEntry = IISAdmin.Children.Add(AppName, "IIsWebVirtualDir") VDir.Properties("Path").Item(0) = Path If IsApplication Then VDir.Properties("AppFriendlyName").Item(0) = AppName End If VDir.Properties("EnableDirBrowsing").Item(0) = False VDir.Properties("AccessRead").Item(0) = True VDir.Properties("AccessExecute").Item(0) = False VDir.Properties("AccessWrite").Item(0) = IsWrite VDir.Properties("AccessScript").Item(0) = RunScripts VDir.Properties("AuthNTLM").Item(0) = True VDir.Properties("EnableDefaultDoc").Item(0) = True VDir.Properties("DefaultDoc").Item(0) = "default.htm,default.aspx,default.asp" VDir.Properties("AspEnableParentPaths").Item(0) = True 'VDir.Properties("AppCreate").Item(0) = False VDir.CommitChanges() 'the following are acceptable params 'INPROC = 0 'OUTPROC = 1 'POOLED = 2 If IsApplication Then VDir.Invoke("AppCreate", 1) Else VDir.Invoke("AppCreate", False) End If Catch Ex As Exception If PathCreated Then System.IO.Directory.Delete(Path) End If 'MsgBox(Ex.Message) End Try End If End Sub

  Read the article

• Trying to pass Model down to partial, how do I do this?

  - by mrblah

  My action creates a strongly typed viewdata, which is passed to my view. In the view, I pass the Model to the render partial method. public ActionResult Index() { ViewDataForIndex vd = new ViewDataForIndex(); vd.Users = Users.GetAll(); return View(vd); } public class ViewDataForIndex: ViewData { public IList<User> Users {get;set;} } now in the view: <%@ Page Language="C#" MasterPageFile="~/Views/Shared/Site.Master" Inherits="System.Web.Mvc.ViewPage<ViewDataForIndex>" %> <% Html.RenderPartial("~/controls/blah.ascx", ViewData.Model); %> and in blah.ascx: <%@ Control Language="C#" Inherits="System.Web.Mvc.ViewUserControl" %> how do I access my model now? if I wanted to create a strongly typed class for my ViewUserControl, how would I do that? inherit from?

  Read the article

• Open file - Security warning

  - by joker

  Does anyone know how to disable the unknown publisher security warning when running an application in Windows Xp Home? It's pretty annoying to have to click run everytime... I have tried: Run gpedit.msc, and go to Local Computer Policy-User Configuration-Administrative Templates-Windows Components-Attachment Manager and enable "Default risk level for file attachments", and then enable "Inclusion list for low risk file types" and add to this list the file extensions that you want to open without triggering this crap. But this file 'gpedit.msc' doest not exist on my computer, i checked system32 folder also =/ maybe its for xp pro

  Read the article

• LSI RAID monitor reports "Consistency Check inconsistency logging disabled"

  - by carlpett

  I have a server with a LSI MegaRAID 9261-8i controller. Recently I started getting alerts like this one: Controller ID: 1 Consistency Check inconsistency logging disabled, too many inconsistencies on VD: 0 Generated on:Sat May 12 04:06:40 2012 SYSTEM DETAILS--- IP Address: 192.168.1.29 OS Name: Windows 7 x64 OS Version: 6.01 Driver Name: megasas.sys Driver Version: 4.5.1.64 IMAGE DETAILS--- BIOS Version: 2.120.33-1197 Firmware Package Version: 12.12.0-0045 Firmware Version: 3.21.00_4.11.05.00_0x05000000 VD 0 is a RAID mirror containing the system disk. I have searched and read, but cannot find any trace of how to actually do anything about this. I tried running a scandisk but that did not find anything (as I expected, since scandisk reads the disks as exposed by the controller, right?). The MegaRAID Storage Manager does not as far as I can see have any options for checking or fixing physical disks. The program claims the VD is "healty", and both disks have Error count 0. Also a bit strange is the System details in the message... The IP address is associated with the RAS (dial in) interface, and the OS should be Windows Server 2011 SBS. Has anyone else experienced this before? What can be done?

  Read the article

• Dell PERC 5 - RAID-10 keeps rebuilding drive 2 every day

  - by raid question

  I have a Dell PowerEdge 2950 with this card: RAID bus controller [0104]: Dell PowerEdge Expandable RAID controller 5 [1028:0015] and six disks in a RAID-10. I replaced drive 2, because it didn't show up, and then it started to rebuild itself: root@backup01:~# megaraidsas-status -- Arrays informations -- -- ID | Type | Size | Status a0d0 | RAID 10 | 5587GiB | DEGRADED -- Disks informations -- ID | Model | Status | Warnings a0e8s0 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s1 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5394 a0e8s2 | ATA ST2000DM001-1E61 1863GiB | rebuild | errs: media:0 other:99 a0e8s3 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s4 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 a0e8s5 | ATA ST2000DM001-9YN1 1863GiB | online | errs: media:0 other:5393 The rebuild finishes, then the virtual drive becomes optimal, and drive 2 goes online. Then once a day, drive 2 acts like it's been removed, and the rebuild starts all over again. How do I make this once a day rebuild stop? Event Description: Removed: PD 02(e1/s2) Event Description: Removed: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: State change on VD 00/0 from OPTIMAL(3) to DEGRADED(2) Event Description: VD 00/0 is now DEGRADED1 Event Description: State change on PD 02(e1/s2) from ONLINE(18) to FAILED(11) Event Description: State change on PD 02(e1/s2) from FAILED(11) to UNCONFIGURED_BAD(1) Event Description: Background Initialization failed on VD 00/0 Event Description: Inserted: PD 02(e1/s2) Event Description: Inserted: PD 02(e1/s2) Info: enclPd=08, scsiType=0, portMap=04, sasAddr=1221000002000000,0000000000000000 Event Description: PD 02(e1/s2) is not a certified drive Event Description: State change on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from UNCONFIGURED_GOOD(0) to OFFLINE(10) from UNCONFIGURED_BAD(1) to UNCONFIGURED_GOOD(0) Event Description: Rebuild automatically started on PD 02(e1/s2) Event Description: State change on PD 02(e1/s2) from OFFLINE(10) to REBUILD(14)

  Read the article

• Apache - virtualhost - works only one

  - by user1811829

  I need a couple of virtualhosts on my local dev machine. Unfortunately it needs to be windows. httpd-vhost.conf <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "C:/xampp/htdocs" ServerName localhost </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "C:/xampp/htdocs/manadom.local/public" ServerName manadom.local ErrorLog "logs/manadom.local-error.log" CustomLog "logs/manadom.local-access.log" combined </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "C:/xampp/htdocs/galeriabiznesu" ServerName gb.loc ErrorLog "logs/gb.loc-error.log" CustomLog "logs/gb.loc-access.log" combined </VirtualHost> And hosts file: 127.0.0.1 localhost 127.0.0.1 manadom.local 127.0.0.1 gb.loc The problem is: localhost points to C:/xampp/htdocs/manadom.local/public manadom.local points to C:/xampp/htdocs/manadom.local/public too gb.loc points to C:/xampp/htdocs/manadom.local/public I can't idea what's wrong? Please help me, i'm not an admin but i read about it lot and i don't know what possibly i can do wrong.

  Read the article

• mod_pagespeed is rewriting but not combining

  - by Marc vd M

  I have the following problem. I installed mod_pagespeed but i am not getting the results i want! It does rewrite my css and changes the to the cache url but its not combining the css files. I have seached the web and stackoverflow for it but did not find a solution. Here are the tags <link media="all" type="text/css" href="http://domain.com/assets/css/bootstrap.min.css.pagespeed.ce.Iz3TwZXylG.css" rel="stylesheet"> <link media="all" type="text/css" href="http://domain.com/assets/css/W.jquery-ui-1.8.24.custom.css.pagespeed.cf.9yjmvb9yjz.css" rel="stylesheet"> <link media="all" type="text/css" href="http://domain.com/assets/css/W.bootstrap.extend.css.pagespeed.cf.VelsS-YQRX.css" rel="stylesheet"> <link media="all" type="text/css" href="http://domain.com/assets/css/W.base.css.pagespeed.cf.QO1yNADs1p.css" rel="stylesheet"> <link media="all" type="text/css" href="http://domain.com/assets/css/W.style.css.pagespeed.cf.tRzIhRbblc.css" rel="stylesheet">

  Read the article

• Matlab Correlation Function

  - by Joka

  function letter=read_char(imgn, num_letters) global templates comp=[ ]; for n=1:num_letters sem=corr2(imgn, templates{1,n}); comp=[comp sem]; end vd=find(comp==max(comp)); Can someon please explain what the 'FOR' loop does and how 'vd' is calculated? Also, what is the variable 'comp' and what will it looks like as the array also contains itself and another variable 'sem' which is calculated from the corr2 function. thanks

  Read the article

• jQuery Colorbox Iframe and Selector

  - by Joker

  I have this: $("a.money").colorbox({href:$("a.money").attr("href")+" div#content"}); Which opens an overlay but only of the content within the #content selector. If I add iframe:true, this will no longer work. Is there a way to get it to work with an iframe? Edit: The closest I could get it to work was by doing this: $("a.money").colorbox({iframe:true, width:700, height:425, onComplete: function() { alert('test'); $test = $("#cboxLoadedContent iframe").contents().find("#content").html(); $("#cboxLoadedContent iframe").contents().find("#container").html($test); } }); Although without the alert it doesn't appear to work, I looked into that and I think I need to use .live(), which led me to trying this: $('a.money').live('click', function() { url = this.href; // this is the url of the element event is triggered from $.fn.colorbox({href: url, iframe:true,width:700, height:425, onComplete: function() { $test = $("#cboxLoadedContent iframe").contents().find("#content").html(); $("#cboxLoadedContent iframe").contents().find("#container").html($test); } }); return false; }); Didn't work, I still needed to add an alert to make it work. In case you might be wondering what I'm trying to do. The webpage is loaded in the iframe, with all the elements in the #container, so that includes #header, #sidebars, but I only want to show the #content inside the iframe. However, this led me to another problem I realized. Assuming I got this to work without the alert, it will only work for that initial page. For example, if I loaded up a form in the iframe, after submitting the form, I would once again see the whole layout instead of just the #content portion. Is it possible to continue only showing the #content portion of the page upon further navigation?

  Read the article

• PHP manipulating multidimensional array values

  - by Joker

  I have a result set as an array from a database that looks like: array ( 0 => array ( "a" => "something" "b" => "something" "c" => "something" ) 1 => array ( "a" => "something" "b" => "something" "c" => "something" ) 2 => array ( "a" => "something" "b" => "something" "c" => "something" ) ) How would I apply a function to replace the values of an array only on the array key with b? Normally I would just rebuild a new array with a foreach loop and apply the function if the array key is b, but I'm not sure if it's the best way. I've tried taking a look at many array functions and it seemed like array_walk_recursive is something I might use, but I didn't have luck in getting it to do what I want. If I'm not describing it well enough, basically I want to be able to do as the code below does: $arr = array(); foreach ($result as $key => $value) { foreach ($value as $key2 => $value2) { $arr[$key][$key2] = ($key2 == 'b' ? $this->_my_method($value2) : $value2); } } Should I stick with that, or is there a better way?

  Read the article

• Making an rtf document right to left

  - by Joker

  I hava an rtf document. I want to change the entire document to be right to left instead of left to right in code. i know the rtf specification is a standard, and should probably use rtldoc (http://msdn.microsoft.com/en-us/library/aa140283(office.10).aspx) only problem is I don't know where to put it. Any other way?

  Read the article

• .net mvc2 custom HtmlHelper extension unit testing

  - by alex

  My goal is to be able to unit test some custom HtmlHelper extensions - which use RenderPartial internally. http://ox.no/posts/mocking-htmlhelper-in-asp-net-mvc-2-and-3-using-moq I've tried using the method above to mock the HtmlHelper. However, I'm running into Null value exceptions. "Parameter name: view" Anyone have any idea?? Thanks. Below are the ideas of the code: [TestMethod] public void TestMethod1() { var helper = CreateHtmlHelper(new ViewDataDictionary()); helper.RenderPartial("Test"); // supposingly this line is within a method to be tested Assert.AreEqual("test", helper.ViewContext.Writer.ToString()); } public static HtmlHelper CreateHtmlHelper(ViewDataDictionary vd) { Mock<ViewContext> mockViewContext = new Mock<ViewContext>( new ControllerContext( new Mock<HttpContextBase>().Object, new RouteData(), new Mock<ControllerBase>().Object), new Mock<IView>().Object, vd, new TempDataDictionary(), new StringWriter()); var mockViewDataContainer = new Mock<IViewDataContainer>(); mockViewDataContainer.Setup(v => v.ViewData) .Returns(vd); return new HtmlHelper(mockViewContext.Object, mockViewDataContainer.Object); }

  Read the article

• Trying to configure DNS on a Godaddy Virtual Dedicated host, Mediatemple Domain Registration

  - by dclowd9901

  A client of mine purchased VD hosting with Godaddy and a domain name with Mediatemple. I've never configured DNS from scratch, and I'm finding it very difficult to find any sort of explanation on how to go about it. As of right now, Mediatemple is pointing to the Godaddy's ns1.domaincontrol.com and ns2.domaincontrol.com nameservers. The VD hosting on Godaddy (via their Simple Control Panel) has options to "Add a new domain", which brings you through a wizard of sorts that asks you if the domain has already been registered (yes), what it is (dclowd9901.com for this example), create a system username and password for it (with checkboxes for SSH and FTP access), which level of user can administer it, and whether a mail account should be setup. When complete, it also creates a zone file. In this zone file, the Primary nameserver is ns1.dclowd9901.com; the records are as follow (where 12.23.12.34 is the presumed host): @ A 12.23.12.34 @ NS ns1 @ NS ns2 ns1 A 12.23.12.34 ns2 A 12.23.12.34 @ MX mail www A 12.23.12.34 ftp A 12.23.12.34 ssh A 12.23.12.34 mail A 12.23.12.34 If anyone can shed any light on this for me, explain to me the interactions between the registrar and the host and so on, I'd be very grateful. Thanks in advance for the help.

  Read the article

• 12.04.1 no audio through HDMI

  - by JoJo

  having a bit of an issue with getting audio to go through HDMI. Here are the base specs: OS: Ubuntu Desktop 12.04.1 x64 CPU: AMD A10-5800K 3.8G 4M FM2 R Mobo: MSI FM2-A75MA-E35 OS: Ubuntu 12.04.1 LTS Vid Card: (integrated on CPU) AMD Radeon HD 7660D HDMI sound works fine under Win7 (after mobo and vid drivers are installed), so it's not physically broken. Audio through the normal headphone jacks works fine under Ubuntu. Looking at the audio panel, there is no HDMI output at all. aplay -l also reports only: card 0: Generic [HD-Audio Generic], device 0: ALC887-VD Analog [ALC887-VD Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 In additional drivers there are two versions: ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER ATI/AMD PROPRIETARY FGLRX GRAPHICS DRIVER (post-release update) The first installs, but problem persists. I do get more resolutions to pick from. Second version does not, reporting it failed installation and to find details at: /var/log/jockey.log Looked at the log, and it's insanely long, if necessary I can get it to you guys. Did more research and some had luck by manually installing the drivers, so tried to give that a shot by following this: https://help.ubuntu.com/community/BinaryDriverHowto/ATI#Manually_installing_Catalyst_12.6 starting at 3.1 Manually installing Catalyst 12.6. I immediately had 2 issues, (1) the AMD website does not provide any drivers for Linux, and (2) the following command did not work: sudo sh amd-driver-installer-12-6-x86.x86_64.run --buildpkg Ubuntu/precise sh: 0: Can't open amd-driver-installer-12-6-x86.x86_64.run Some other posts stated to update "alsa-drivers", but that also did not work as install command for the new version of them did not work. I forget the exact issue, but similar to above, cannot open / cannot find. Any help would be greatly appreciated!

  Read the article

1 2 3  | Next Page >