Search Results

Search found 7 results on 1 pages for 'kairan'.

Page 1/1 | 1 

• Vertex 2 SSD is running faster than my Vertex 3 SSD?

  - by Kairan

  I used Acronis Disk Director to do a direct clone of my C:\ windows 7 x64 drive from my Vertex 2 to my new Vertex 3 SSD (Just to show the drive software winstall everything is identical.) I ran a performance test on Windows using the Windows Experience Index. The rating I am receiving when booting on the Vertex 2 is 7.5 While I am getting only a rating for the Vertex 3 of 6.9 My understanding is that the read/write speeds of the Vertex 2 is only up to 250MB/sec while the Vertex 3 is up to 500MB/sec. Copying a single file (3GB in size) from the Vertex 3 to itself was getting speed of approx 70-80MB/sec This speed is no better (maybe worse) than what I got from the Vertex 2 I am connected via the SATA 3 port on the motherboard, using an SATA 3 cable Is this issue caused by the drive cloning? Do I have a bad SSD?

  Read the article

• Windows 7 Disk Management Spanned Volume vs Striped Volume

  - by Kairan

  Im looking for a reason why a person would use a Spanned volume rather than a Striped volume? If my understanding is correct Striped: Faster read/write speed than spanned, but I "assume" more wear+tear Spanned: No speed benefit like striped, but data is written sequentially and fills up Drive1 before filling up Drive2, so it saves on wear+tear Beyond that Im not sure if there is any other deciding factor on which to use. Definition found below: A striped volume uses the free space on more than one physical hard disk to create a bigger volume. Unlike a spanned volume, a striped volume writes across all volumes in the stripe in small blocks, distributing the load across the disks in the volume. The portions of disk used to create the volume need to be the same size; the size of the smallest free space included in the striped volume will determine.

  Read the article

• Remote Control Adapter for PC

  - by Kairan

  Does there exist a product out there that attaches to your PC (preferably USB) that enables Infrared signals to be received (by a regular remote control) ? It seems a novel idea to be able to get a programmable remote that can be used to manipulate windows (like the Harmony remote control series) along with some programmable software (preferably Windows supported) to convert any button on a regular remote to some command on the PC. Does this exist? What is it called? This particular instance you are REQUIRED to use the crappy supplied remote, and this is not what I am looking for

  Read the article

• How to keep Ubuntu 11.10 and Kate editor w/terminal from changing command line when changing tabs?

  - by Kairan

  I am programming C using Kate editor in Ubuntu 11.10. It works great, but when I change tabs in Kate, the terminal line changes to the file path of the tab I click on. Normally this is not a big deal (other than annoyingly adding extra text to my terminal) however if I am currently RUNNNING a C program, it obviously will type at the command line, which is not so cool. Example terminal window for my C program (its at a menu): 1) select opt 1 2) select opt 2 Enter choice: (here it waits for prompt from user) Now when I click a tab in Kate, it wants to put in the cd / path of the file in that tab, such as: cd /home/user/os/files And of course since my terminal was waiting for prompt from user it gets that command.. not good. Perhaps there is no fix, but maybe someone knows? Obviously I could choose NOT to switch tabs or end program before switching tabs... Note: I probably made the mistake of putting this under StackOverflow which is more of a programming area - so though repost here might be best (I am not sure how to link the questions but will paste hyperlink to that post - I dont want to violate any stackoverflow/superuser violations) Suggestions on merging them are welcome or if I should delete one? StackOverFlow Question

  Read the article

• Acronis Disk Director AFTER Clone Disk error: PXE-E61: Media test failure, check cable

  - by Kairan

  Used Acronis Disk Director on my desktop, plugged in the laptop drive 240GB SSD (USB) and the new hard drive 500GB SSD (usb) and the copy seemed to be fine. I didnt see any error messages but I didnt stare at it for 3 hours either. The clone disk of course the Toshiba hidden restore partition, the primary partition C drive and the active (boot?) partition and yes, did check box for copy NT signature. The computer boots up fine most of the time, but it seems that when the computer goes to sleep (i believe its sleep, hard to do much testing during school) or hibernate or reboot it will sometimes display this message: Intel(R) Boot Agent GE v1.3.52 Copyright (C) 1997-2010, Intel Corporation PXE-E61: Media test failure, check cable PXE-M0F: Exiting Intel Boot Agent Insert system disk in drive. Press any key when ready... Of course any key does nothing but repeat a similar method. However, if I press the power button on the laptop (Toshiba Portege R705, Win 7 Pro 64-bit) it puts computer into hibernate. After hibernating I press power button again and it comes out of hibernation without any odd messages or problems described above... so apparently that is my TEMP fix. Another recent issue I noticed is on occasion when creating a new folder or modifying something in the system variables, other random areas I will get a message: "The Stub received bad data" and simply retry the task and it works. Perhaps these two issues are linked.

  Read the article

• Disk Management Hidden Partitions - PTEDIT32

  - by Kairan

  Apparently PTEDIT32 can edit partitions, making partitions that are hidden, visible. My purpose is to take a hidden partition on a toshiba laptop (the recovery partition) and copy it as my hard drive is beginning to fail. My problem, is that I cannot find PTEDIT32 documentation on what i want to change the partition # to. I know that changing it from 27 to 7 would change it from hidden to active - but if I set it to active, I am worried it will try to launch the recovery mode (as that is what it did on a previous laptop) Here is the link I used for instructions to do this on a previous laptop: Hidden_Recovery_Link_Site So how to make the hidden partition visible without it actually RUNNING the recovery mode?

  Read the article

• Mini DV and DVI Conversion

  - by Kairan

  Video card is: AMD HD 6950 My video card comes with 1xHDMI, 2xDVI, and 2xMini DV ports. I have always used VGA and DVI only. I have the HDMI already connected. I want to hook up 2 more display. One of the display can take a VGA only, the other is an LCD TV so it has VGA, HDMI, Component. I am wondering: 1) What is the best output port to use for the second two monitors? The miniDV or the DVI? 2) I need to run a long cable maybe 15-25 feet, this might change the answer to question 1, is an HDMI long cable 20+ ft going to be better than a 20ft DVI or miniDV ?

  Read the article

1