Search Results

Search found 11 results on 1 pages for 'linuxpenseur'.

Page 1/1 | 1 

• Telnet disconnected on login failure

  - by LinuxPenseur

  Hi, I have two servers running Linux 2.6.9 kernel. When i telnet to server1 , the telnet will be disconnected only after 3 login failures. While, when i telnet to server2, telnet will be disconnected after the first login failure. I expect server2 to behave the same way as server1 when telnet is executed. Kindly tell me where i should tweak my servers so that i could achieve what i expect. Thanks, LinuxPenseur

  Read the article

• RTNETLINK answers: Invalid argument

  - by LinuxPenseur

  When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

  Read the article

• command to show the shell command prompt

  - by LinuxPenseur

  Hi, Is there a shell command to display the command prompt. I will explain what i want through the illustration below. When i execute script.sh, i should get the following output $sh script.sh $ /* command prompt and then print hi */ hi My script.sh is like this #! /bin/bash <command to display the shell command prompt> echo "hi" exit 0 what should the code that has to go in the place of angle brackets to get an output like above? Thanks

  Read the article

• command to show the shell command prompt

  - by LinuxPenseur

  Hi, Is there a shell command to display the command prompt. I will explain what i want through the illustration below. When i execute script.sh, i should get the following output $sh script.sh $ /* command prompt and then print hi */ hi My script.sh is like this #! /bin/bash <command to display the shell command prompt> echo "hi" exit 0 what should the code that has to go in the place of angle brackets to get an output like above? Thanks

  Read the article

• Run shell script on a command

  - by LinuxPenseur

  Hi, I want to run a shell script when date -s <string> command is used. For example i want to log the command to the file /tmp/user.log by executing the following command in the shell script logger -p user.notice "date -s command executed" -f /tmp/user.log How can run a shell script when date -s <string> is executed on the shell? To make it more general, I want to run my shell script when someone else issues a particular linux command on my system. How to do this?

  Read the article

• RTNETLINK answers: Invalid argument

  - by LinuxPenseur

  Hi, When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

  Read the article

• Log "date -s" command

  - by LinuxPenseur

  Hi, I know that the date -s <STRING> command sets the time described by the string STRING. What i want is to log the above command whenever it is used to set the time into the file /tmp/log/user.log. In my Linux distribution the logging is done by syslog-ng. I already have some logs going into /tmp/log/user.log. This is the content of /etc/syslog-ng/syslog-ng.conf in my system for logging into /tmp/log/user.log destination d_notice { file("/tmp/log/user.log");}; filter f_filter10 { level(notice) and not facility(mail,authpriv,cron); }; log { source(s_sys); filter(f_filter10); destination(d_notice); }; What should i do so that date -s command is also logged into /tmp/log/user.log

  Read the article

• Show command prompt on reboot

  - by LinuxPenseur

  Hi, In one of my linux machines, when i give reboot command at the shell command prompt then press enter, i get another command prompt and then the system reboots. $reboot $ But in one of my office Linux machines, when i give the reboot command, it suddenly reboots without showing another shell command prompt What could be the reason for this? I need the first behavior to be present in my office machine also. Kindly tell me where i should tweak my office machine. Thanks

  Read the article

• Question on date and timezone in Linux

  - by LinuxPenseur

  Hi , I did the date command and it gave the following output root@localhost:~$ date Thu Dec 30 14:19:47 UTC 2010 Then i modified the date using date -s command whichn gave the following output root@localhost:~$ date -s "12/30/2010 JST 14:19:47" Thu Dec 30 05:19:47 UTC 2010 I noticed that the time changed to 9 hours behind UTC time to show exactly the JST time. But timezone as you can see is still showing UTC. Why is it showing the correct time and incorrect timezone? Thanks

  Read the article

• Difference in behavior of reboot

  - by LinuxPenseur

  Hi, I have 2 machines running linux. In one machine, the reboot command is an executable normally found in all linux distributions. In the second machine the reboot command is a shell script customized using some other hardware tool commands to reboot the system. One behavior difference between the 2 machines is that when i execute reboot command on the first machine, it shows another shell prompt and then only reboots. But in the case of second machine, it reboots without showing a shell prompt. I expect the second machine to behave the same way as first machine when reboot command is given. Currently i am analyzing the source code of shutdown.c and halt.c normally found in linux distributions, so that i can find out the implementation which produces the shell propmt on reboot and use that in the shell script in second machine. Kindly give me some pointers on where i should start looking to find the implementation. Thanks

  Read the article

• Run shell command from child shell

  - by LinuxPenseur

  Hi, I have a Unix shell script test.sh. Within the script i would like to invoke another shell and then execute the rest of the commands in the shell script from the child shell and exit To make it clear: test.sh #! /bin/bash /bin/bash /* create child shell */ <shell-command1> <shell-command2> ...... <shell-commandN> exit 0 What my intention is to run the shell-commands1 to shell-commandN from the child shell. Kindly tell me how to do this

  Read the article

1