Search Results

Search found 20 results on 1 pages for 'madwifi'.

Page 1/1 | 1 

  • Ubuntu, No wireless networks found after correctly installed madwifi

    - by Peter
    Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

    Read the article

  • Determining Maximum Txpower a WiFi Card Supports?

    - by BigGenius
    I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

    Read the article

  • cannot get my wifi to work on my acer aspire 5552

    - by stuart
    I am very new to this forum and also linux. I have managed to install wubi on my laptop fine and I can get on the net with ethernet, But when I try to download and install the wifi drivers it keeps giving me what I think is a generic var/ log error and just starts to hang on install then says it will not install. Can anyone help please as I really really want to move from windows and this is not helping me..A big thanks in advance :)

    Read the article

  • Atheros AR2413 wireless not working after shutdown

    - by Chandrasekhar
    I am using a Ubuntu 11.04 on an Acer aspire 3680 laptop and my wifi is not working. I followed the below commands to install the madwifi driver: sudo su apt-get install subversion cd /usr/src svn checkout http://madwifi-project.org/svn/madwifi/trunk madwifi tar cfvz madwifi.tgz cd madwifi make && make install echo "blacklist ath5k" /etc/modprobe.d/blacklist.conf echo "ath_pci" /etc/modules modprobe ath_pci sudo reboot After installation I am facing the same problem. My wifi wont work after I shutdown. Infact it didn't work after suspend but I rectified that problem by the following commands: Command 1: sudo rmmod -f ath_pci sudo rfkill unblock all sudo modprobe ath_pci along with the command SUSPEND_MODULES=ath_pci added to the /etc/pm/config.d/madwifi directory. So if I suspend and then on my laptop the wifi loads well and doesn't create a problem. But if I shutdown my laptop the wifi never loads again and eachtime I have to run a Ubuntu 9.04 live CD to load it. I did try adding the Command 1 to the /etc/rc.local directory but still it doesn't work. So my question is: What should I do in order to make my wireless work without having to run a live CD of ubuntu 9.04 everytime after shutdown? Thanks. Here are the outputs which one might need: Output 1 chandru@chandru-acer:~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 0a:03.0 Ethernet controller: Atheros Communications Inc. AR2413 802.11bg NIC (rev 01) 0a:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 0a:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) Output 2: lsmod Module Size Used by wlan_tkip 17074 2 binfmt_misc 13213 1 parport_pc 32111 0 ppdev 12849 0 snd_hda_codec_si3054 12924 1 snd_hda_codec_realtek 255882 1 joydev 17322 0 snd_atiixp_modem 18624 0 snd_via82xx_modem 18305 0 snd_intel8x0m 18493 0 snd_ac97_codec 105614 3 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m snd_hda_intel 24113 2 ac97_bus 12642 1 snd_ac97_codec snd_hda_codec 90901 3 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_hda_intel i915 451053 3 snd_hwdep 13274 1 snd_hda_codec snd_pcm 80042 7 snd_hda_codec_si3054,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec snd_seq_midi 13132 0 snd_rawmidi 25269 1 snd_seq_midi drm_kms_helper 40971 1 i915 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event pcmcia 39671 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq drm 184164 4 i915,drm_kms_helper yenta_socket 27230 0 tifm_7xx1 12898 0 wlan_scan_sta 21945 1 ath_rate_sample 17279 1 pcmcia_rsrc 18292 1 yenta_socket psmouse 73312 0 tifm_core 15040 1 tifm_7xx1 snd 55295 18 snd_hda_codec_si3054,snd_hda_codec_realtek,snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_ac97_codec,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device serio_raw 12990 0 i2c_algo_bit 13184 1 i915 soundcore 12600 1 snd pcmcia_core 21505 3 pcmcia,yenta_socket,pcmcia_rsrc video 19112 1 i915 ath_pci 183044 0 snd_page_alloc 14073 5 snd_atiixp_modem,snd_via82xx_modem,snd_intel8x0m,snd_hda_intel,snd_pcm wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci lp 13349 0 parport 36746 3 parport_pc,ppdev,lp usbhid 41704 0 hid 77084 1 usbhid sky2 49172 0 Output 3 root@chandru-acer:~# lshw -C network PCI (sysfs) *-network description: Ethernet interface product: 88E8038 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 14 serial: 00:16:36:fb:aa:64 capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.28 firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:44000000-44003fff ioport:2000(size=256) *-network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wifi0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci ip=192.168.1.6 latency=96 maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11g resources: irq:18 memory:d0000000-d000ffff Output 4 root@chandru-acer:~# lsmod | grep ath_pci ath_pci 183044 0 wlan 224640 5 wlan_tkip,wlan_scan_sta,ath_rate_sample,ath_pci ath_hal 398701 3 ath_rate_sample,ath_pci

    Read the article

  • Problem with wireless networking

    - by Rodnower
    Hello, I have atheros wifi hardware, intell chipset, gigabyte laptop and CentOS 5 installed. Now I try to use wireless network and get problems. First of all I want to say that I have 2 OS on my laptop, and when I load Windows XP I still may to access to the wireless network. First I try to get it on Linux was to make active wlan0 interface in: system - administration - network but I get: Determining IP information for wlan0... failed. Second I try also was unsuccessfully: [root 1 network-scripts]# ifup-wireless Error : unrecognised wireless request "off" This relevant output of iwconfig is: Warning: Driver for device wlan0 recommend version 21 of Wireless Extension, but has been compiled with version 20, therefore some driver features may not be available... wlan0 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 {output not in the original format} The same things are happen even if I do: modprobe wlan0 (this not get error) Important to say that modprobe not succeed to find ath_pci, tharefor I decide to download latest version of the madwifi driver from http://madwifi-project.org. I extracted this, but when I make this, this is what I get: [root 1 madwifi-0.9.4]# make /bin/sh: line 0: cd: /lib/modules/2.6.18-164.el5/build: No such file or directory Makefile.inc:66: * /lib/modules/2.6.18-164.el5/build is missing, please set KERNELPATH. Stop. I tried to set KERNELPATH, but I think that it was incorrect: [root 1 madwifi-0.9.4]# make KERNELPATH=/lib/modules/2.6.18-164.el5/kernel/ /bin/sh: cc: command not found Makefile.inc:81: * Cannot detect kernel version - please check compiler and KERNELPATH. Stop. Some one have any ideas? Thank you very much for ahead.

    Read the article

  • Atheros wireless not working

    - by Chandru1
    I have been struggling hard since i have installed Ubuntu 10.10 but it has been difficult for me to get my wifi working. So here is what i tried. First i checked whether i have the driver using the ifconfig command and it shows the wireless lan driver as wlan0. Next, i tried the command iwlist wlan0 scanning by becoming the root which gave me the output as no scan results. Next, i visited this link https://help.ubuntu.com/community/WifiDocs/Driver/Atheros to see as to what problem my laptop may have. I do own have an ath5k chipset. And as i followed the instructions in the above link in one of the blacklist-ath_pci.conf file had this written in it. For some Atheros 5K RF MACs, the madwifi driver loads buts fails to correctly initialize the hardware, leaving it in a state from which ath5k cannot recover. To prevent this condition, stop madwifi from loading by default. Use Jockey to select one driver or the other. (Ubuntu: #315056, #323830 I am not that good at Linux but i have given it a try. I am desperate to have my wifi working and i would be glad if this community could help. ADDED: If anyone would like to know as to what drivers i am using this is the output. network description: Wireless interface product: AR2413 802.11bg NIC vendor: Atheros Communications Inc. physical id: 3 bus info: pci@0000:0a:03.0 logical name: wlan0 version: 01 serial: 00:19:7d:d3:0c:fd width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath5k driverversion=2.6.35-24-generic firmware=N/A latency=168 link=no maxlatency=28 mingnt=10 multicast=yes wireless=IEEE 802.11bg resources: irq:18 memory:d0000000-d000ffff Some more information and output as to what i have done. lsmod | grep ath ath5k 130083 0 mac80211 231541 1 ath5k ath 8153 1 ath5k cfg80211 144470 3 ath5k,mac80211,ath led_class 2633 1 ath5k

    Read the article

  • Archlinux/atheros WLAN configuration troubles

    - by GrinReaper
    I'm trying to config archlinux to use my wireless network adapter. It's quite troublesome. From what I've gathered, it's an atheros network adapter, using the ath5k driver/module... I can't get it to work; any ideas? Here's some of the output from my tinkering: # lspci | grep -i net 00:0a.0 Ethernet controller: nVidia corporation MCP67 Ethernet (reva2) 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) # lsusb ... Bus 004 Device 003: ID 03f0:17d Hewlett Packard Wireless (Bluetooth + WLAN Interface [Integrated Module] # ping -c 3 www.google.com ping: unknown host www.google.com #ping -c 3 8.8.8.8 ping: network is unreachable # lspci -v 03:00.0 Ethernet controller: atheros communications inc. AR5001 Wireless Network Adapter (rev01) ... Kernel driver in use: ath5k Kernel modules: ath5k # dmesg |grep ath5k registered as phy0 registered led device ath5k: atheros chip found PCI INT A disabled registered led device registered as phy1 # ip addr | sed '/^[0-9]/!d;s/: <.*$//' 1: lo 2: eth1 3: eth0 # ip link set <interface> up/down RNETLINK answers: Operation not possible due to RF-kill Also, is there a way to dump text from command-line to a text file so i can just copy pasta? Sorry, first time using a linux distro... EDIT: So I just tried this: I actually just did this twice. (I can't tell which setting is on/off for my wireless adapter. The lights are blue all the time now.) #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :yes 1: hp-bluetooth: bluetooth softblocked: no hardblocked :yes 3: phy1: wireless lan softblocked: no hardblocked :yes #rfkill list 0: hp-wifi: wireless lan softblocked: no hardblocked :no 1: hp-bluetooth: bluetooth softblocked: no hardblocked no 3: phy1: wireless lan softblocked: no hardblocked :yes 7: hci0: bluetooh 0: hp-wifi: wireless lan softblocked: no hardblocked :no I've dug around some other articles and it seems like ath5k is supposed to be preferable to madwifi, so should i be using madwifi? I'm 99% sure I disabled the hardblock (by turning it ON) but, as shown above, phy1 wireless lan is STILL hardblocked. What gives? Maybe I've made some more fundamental error in a basic config file? EDIT: I've fixed the hardblock. I've tried pinging www.google.com, but to no avail. I get: ping: unknown host www.google.com In the arch wiki: Edit /etc/hosts and add the same HOSTNAME you entered in /etc/rc.conf: 127.0.0.1 archlinux.domain.org localhost.localdomain localhost archlinux To my understanding, hostname is just a user-specified and based on preference(?) My /etc/rc.conf: HOSTNAME="gestalt" My /etc/hosts: 127.0.0.1 localhost.localdomain localhost gestalt but should it be the following? 120.0.0.1 localhost.domain.org localhost.localdomain localhost gestalt

    Read the article

  • WPA Connection problem

    - by Renjith G
    hi , I am using hostapd,wireless tools with madwifi for my wireless ap in my board. The WEP, WPA-PSK connections and communications between my board and my desktop PC, WINDOWS XP SP2) (with OLITEC wireless usb)are fine. But when i configured the WPA type, connection established but it is showing the status in the secuirity dialog box "TKIP - Key Absent" Can any one faced this problem?? /renjith g

    Read the article

  • How can i configure country code in wireless WEP communication?

    - by Renjith G
    hi I need to configure country code between my wireless communication points. I am using madwifi, wireless tools and hostapd set up in my ap(board- linux OS(2.6.10)) , and am using OLITEC stick usb 802.11g card in my windows machine. I can communicate successfully using WEP,WPA-PSK and WPA , but i need to configure some more additional options such as Country code and Beacon period and Beacon interval etc. Expecting the reply, /renjith g

    Read the article

  • Connectify like functionality on Ubuntu running on T61 - wifi 4965 AGN

    - by Vivek Sharma
    I would like to use my laptop as an Access point, so that i can connect my phones through Wifi. I have done this my office laptop T410. I am having T61 with wifi module 4965. Connectify on windows does not support it. I am following -- https://help.ubuntu.com/community/WifiDocs/WirelessAccessPoint to make achieve WAP capability on my T61 running ubuntu 10.10. The link says something about "master mode", how do i put my T61 wifi-inter4965 in master mode. Can i install madwifi or atheros drivers on it. I am using galaxy S froyo, and it does not support Ad-hoc network. Has anyone tired to achieve this.

    Read the article

  • Connectify-like functionality on 4965 AGN wireless?

    - by Vivek Sharma
    I would like to use my laptop as an Access point, so that i can connect my phones through Wifi. I have done this my office laptop T410. I am having T61 with wifi module 4965. Connectify on windows does not support it. I am following these instructions to make achieve WAP capability on my T61 running ubuntu 10.10. The link says something about "master mode", how do i put my T61 wifi-inter4965 in master mode. Can I install madwifi or atheros drivers on it? I am using galaxy S froyo, and it does not support Ad-hoc network. Has anyone tried to achieve this?

    Read the article

  • Again WPA Connection problem even after changed to latest version ..please help

    - by Renjith G
    I am using hostapd, wireless tools with madwifi for my wireless ap in my board. The WEP, WPA-PSK connections and communications between my board with linux and my desktop PC, Windows XP SP2 (with Olitec USB wireless) are fine. But when I configured the WPA type, the connection seems established but shows the status "TKIP - Key Absent" in the security dialog box. Anyone faced this problem? Am attaching the conf files and the connection status. In the AP side am complaining . I am using the in built radius server conf with the hostapd 0.4.7 hostapd.conf interface=ath0 driver=madwifi logger_syslog=0 logger_syslog_level=0 logger_stdout=0 logger_stdout_level=0 debug=0 eapol_key_index_workaround=1 dump_file=/tmp/hostapd.dump.0.0 ssid=Renjith G wpa wpa=1 wpa_passphrase=mypassphrase wpa_key_mgmt=WPA-EAP wpa_pairwise=TKIP CCMP wpa_group_rekey=600 macaddr_acl=2 /* commented */ ieee8021x=1 /* commented */ eap_authenticator=1 own_ip_addr=172.16.25.1 nas_identifier=renjithg.com auth_server_addr=172.16.25.1 auth_server_port=1812 auth_server_shared_secret=key1 ca_cert=/flash1/ca.crt server_cert=/flash1/server.crt eap_user_file=/etc/hostapd.eap_user hostapd.eap_user "*@renjithg.com" TLS And the commands am using are wlanconfig ath0 create wlandev wifi0 wlanmode ap iwconfig ath0 essid Renjith channel 6 ifconfig ath0 192.168.25.1 netmask 255.255.255.0 up hostapd -ddd /etc/hostapd.conf Please correct if am wrong .. Also am getting the debug messages on my AP when am connecting in my windows machine through WPA ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf Configuration file: /etc/hostapd.conf Line 18: obsolete eap_authenticator used; this has been renamed to eap_server madwifi_set_iface_flags: dev_up=0 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'Renjith G wpa' madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA= 0x1 madwifi_set_iface_flags: dev_up=1 madwifi_set_privacy: enabled=1 WPA: group state machine entering state GTK_INIT GMK - hexdump(len=32): 9c 77 cd 38 5a 60 3b 16 8a 22 90 e8 65 b3 c2 86 40 5c be c3 dd 84 3e df 58 1d 16 61 1d 13 d1 f2 GTK - hexdump(len=32): 02 78 d7 d3 5d 15 e3 89 9c 62 a8 fe 8a 0f 40 28 ba dc cd bc 07 f4 59 88 1c 08 84 2b 49 3d e2 32 WPA: group state machine entering state SETKEYSDONE madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 Deauthenticate all stations l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 < Register Fail < Register Fail Wireless event: cmd=0x8c04 len=20 madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state DISCONNECTED WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 ioctl[unknown???]: Invalid argument Wireless event: cmd=0x8c03 len=20 New STA WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state INITIALIZE madwifi_del_key: addr=00:0a:78:a0:0b:09 key_idx=0 WPA: 00:0a:78:a0:0b:09 WPA_PTK_GROUP entering state IDLE WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION WPA: 00:0a:78:a0:0b:09 WPA_PTK entering state AUTHENTICATION2 IEEE 802.1X: 4 bytes from 00:0a:78:a0:0b:09 IEEE 802.1X: version=1 type=1 length=0 NOW am getting the following error message with latest tools. *This is the latest error messages..please refer this only..* ~/wlanexe # ./hostapd -ddd /etc/hostapd.conf TLS: Trusted root certificate(s) loaded madwifi_set_iface_flags: dev_up=0 madwifi_set_privacy: enabled=0 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=2 ioctl[IEEE80211_IOCTL_SETMLME]: Invalid argument madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 2) madwifi_set_privacy: enabled=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=1 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=2 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=3 Using interface ath0 with hwaddr 00:0b:6b:33:8c:30 and ssid 'RenjithGwpa' SSID - hexdump_ascii(len=11): 52 65 6e 6a 69 74 68 47 77 70 61 RenjithGwpa PSK (ASCII passphrase) - hexdump_ascii(len=12): 6d 79 70 61 73 73 70 68 72 61 73 65 mypassphrase PSK (from passphrase) - hexdump(len=32): a6 55 3e 76 94 8b d9 81 a1 22 5e 24 29 83 33 86 11 a8 7e 93 19 7c a9 ab ab cc 12 58 37 e5 35 b6 RADIUS local address: 172.16.25.1:1024 madwifi_set_ieee8021x: enabled=1 madwifi_configure_wpa: group key cipher=1 madwifi_configure_wpa: pairwise key ciphers=0xa madwifi_configure_wpa: key management algorithms=0x1 madwifi_configure_wpa: rsn capabilities=0x0 madwifi_configure_wpa: enable WPA=0x1 WPA: group state machine entering state GTK_INIT (VLAN-ID 0) GMK - hexdump(len=32): [REMOVED] GTK - hexdump(len=32): [REMOVED] WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0) madwifi_set_key: alg=TKIP addr=00:00:00:00:00:00 key_idx=1 madwifi_set_privacy: enabled=1 madwifi_set_iface_flags: dev_up=1 ath0: Setup of interface done. l2_packet_receive - recvfrom: Network is down Wireless event: cmd=0x8b1a len=24 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Data frame from not associated STA 00:0a:78:a0:0b:09 Wireless event: cmd=0x8c04 len=20 Wireless event: cmd=0x8c03 len=20 New STA ioctl[unknown???]: Invalid argument madwifi_process_wpa_ie: Failed to get WPA/RSN IE Failed to get WPA/RSN information element. Data frame from not associated STA 00:0a:78:a0:0b:09

    Read the article

  • kismet on BCM43227

    - by Uttam Baroi
    I am trying to monitor wireless on Broadcom BCM43227, I used sudo airmon-ng to run the monitoring, i get command not found. I installed kismet, when i run, i get this *uttam@UT:~$ sudo kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. uttam@UT:~$* I did check a blog about kismet on Broadcom that says about some binary drivers not allowing to do it... I used iwconfig and it says no extension : what is that well I need to give a hand on air monitoring............ help, how to do it

    Read the article

  • Where does output of print in kernel go?

    - by apoorv020
    I am debugging a driver for linux (specifically ubuntu server 9.04), and there are several printf statements in the code. Where can I view the output of these statements? EDIT1: What i'm trying to do is write to kernel using the proc file-system. The print code is static int proc_fractel_config_write(struct file *file, const char *argbuf, unsigned long count, void *data) { printk(KERN_DEBUG "writing fractel config\n"); ... In kern.log when I see the following message when i try to overwrite the file /proc/net/madwifi/ath1/fractel_config (with varying time of course). [ 8671.924873] proc write [ 8671.924919] Any explainations?

    Read the article

  • Can't install graphic drivers in 12.04

    - by yinon
    The driver is ATI/AMD proprietary FGLRX graphics driver. After clicking Activate, it asks for my password and starts downloading. Then it shows an error message: 2012-10-03 16:16:04,227 DEBUG: updating <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> 2012-10-03 16:16:06,172 DEBUG: reading modalias file /lib/modules/3.2.0-29-generic-pae/modules.alias 2012-10-03 16:16:06,383 DEBUG: reading modalias file /usr/share/jockey/modaliases/b43 2012-10-03 16:16:06,386 DEBUG: reading modalias file /usr/share/jockey/modaliases/disable-upstream-nvidia 2012-10-03 16:16:06,456 DEBUG: loading custom handler /usr/share/jockey/handlers/pvr-omap4.py 2012-10-03 16:16:06,506 WARNING: modinfo for module omapdrm_pvr failed: ERROR: modinfo: could not find module omapdrm_pvr 2012-10-03 16:16:06,509 DEBUG: Instantiated Handler subclass __builtin__.PVROmap4Driver from name PVROmap4Driver 2012-10-03 16:16:06,682 DEBUG: PowerVR SGX proprietary graphics driver for OMAP 4 not available 2012-10-03 16:16:06,682 DEBUG: loading custom handler /usr/share/jockey/handlers/cdv.py 2012-10-03 16:16:06,727 WARNING: modinfo for module cedarview_gfx failed: ERROR: modinfo: could not find module cedarview_gfx 2012-10-03 16:16:06,728 DEBUG: Instantiated Handler subclass __builtin__.CdvDriver from name CdvDriver 2012-10-03 16:16:06,728 DEBUG: cdv.available: falling back to default 2012-10-03 16:16:06,772 DEBUG: Intel Cedarview graphics driver availability undetermined, adding to pool 2012-10-03 16:16:06,772 DEBUG: loading custom handler /usr/share/jockey/handlers/vmware-client.py 2012-10-03 16:16:06,781 WARNING: modinfo for module vmxnet failed: ERROR: modinfo: could not find module vmxnet 2012-10-03 16:16:06,781 DEBUG: Instantiated Handler subclass __builtin__.VmwareClientHandler from name VmwareClientHandler 2012-10-03 16:16:06,795 DEBUG: VMWare Client Tools availability undetermined, adding to pool 2012-10-03 16:16:06,796 DEBUG: loading custom handler /usr/share/jockey/handlers/fglrx.py 2012-10-03 16:16:06,801 WARNING: modinfo for module fglrx_updates failed: ERROR: modinfo: could not find module fglrx_updates 2012-10-03 16:16:06,805 DEBUG: Instantiated Handler subclass __builtin__.FglrxDriverUpdate from name FglrxDriverUpdate 2012-10-03 16:16:06,805 DEBUG: fglrx.available: falling back to default 2012-10-03 16:16:06,833 DEBUG: ATI/AMD proprietary FGLRX graphics driver (post-release updates) availability undetermined, adding to pool 2012-10-03 16:16:06,836 WARNING: modinfo for module fglrx failed: ERROR: modinfo: could not find module fglrx 2012-10-03 16:16:06,840 DEBUG: Instantiated Handler subclass __builtin__.FglrxDriver from name FglrxDriver 2012-10-03 16:16:06,840 DEBUG: fglrx.available: falling back to default 2012-10-03 16:16:06,873 DEBUG: ATI/AMD proprietary FGLRX graphics driver availability undetermined, adding to pool 2012-10-03 16:16:06,873 DEBUG: loading custom handler /usr/share/jockey/handlers/dvb_usb_firmware.py 2012-10-03 16:16:06,925 DEBUG: Instantiated Handler subclass __builtin__.DvbUsbFirmwareHandler from name DvbUsbFirmwareHandler 2012-10-03 16:16:06,926 DEBUG: Firmware for DVB cards not available 2012-10-03 16:16:06,926 DEBUG: loading custom handler /usr/share/jockey/handlers/nvidia.py 2012-10-03 16:16:06,961 WARNING: modinfo for module nvidia_96 failed: ERROR: modinfo: could not find module nvidia_96 2012-10-03 16:16:06,967 DEBUG: Instantiated Handler subclass __builtin__.NvidiaDriver96 from name NvidiaDriver96 2012-10-03 16:16:06,968 DEBUG: nvidia.available: falling back to default 2012-10-03 16:16:06,980 DEBUG: XorgDriverHandler(nvidia_96, nvidia-96, None): Disabling as package video ABI xorg-video-abi-10 does not match X.org video ABI xorg-video-abi-11 2012-10-03 16:16:06,980 DEBUG: NVIDIA accelerated graphics driver not available 2012-10-03 16:16:06,983 WARNING: modinfo for module nvidia_current failed: ERROR: modinfo: could not find module nvidia_current 2012-10-03 16:16:06,987 DEBUG: Instantiated Handler subclass __builtin__.NvidiaDriverCurrent from name NvidiaDriverCurrent 2012-10-03 16:16:06,987 DEBUG: nvidia.available: falling back to default 2012-10-03 16:16:07,015 DEBUG: NVIDIA accelerated graphics driver availability undetermined, adding to pool 2012-10-03 16:16:07,018 WARNING: modinfo for module nvidia_current_updates failed: ERROR: modinfo: could not find module nvidia_current_updates 2012-10-03 16:16:07,021 DEBUG: Instantiated Handler subclass __builtin__.NvidiaDriverCurrentUpdates from name NvidiaDriverCurrentUpdates 2012-10-03 16:16:07,022 DEBUG: nvidia.available: falling back to default 2012-10-03 16:16:07,066 DEBUG: NVIDIA accelerated graphics driver (post-release updates) availability undetermined, adding to pool 2012-10-03 16:16:07,069 WARNING: modinfo for module nvidia_173_updates failed: ERROR: modinfo: could not find module nvidia_173_updates 2012-10-03 16:16:07,072 DEBUG: Instantiated Handler subclass __builtin__.NvidiaDriver173Updates from name NvidiaDriver173Updates 2012-10-03 16:16:07,073 DEBUG: nvidia.available: falling back to default 2012-10-03 16:16:07,105 DEBUG: NVIDIA accelerated graphics driver (post-release updates) availability undetermined, adding to pool 2012-10-03 16:16:07,112 WARNING: modinfo for module nvidia_173 failed: ERROR: modinfo: could not find module nvidia_173 2012-10-03 16:16:07,118 DEBUG: Instantiated Handler subclass __builtin__.NvidiaDriver173 from name NvidiaDriver173 2012-10-03 16:16:07,119 DEBUG: nvidia.available: falling back to default 2012-10-03 16:16:07,159 DEBUG: NVIDIA accelerated graphics driver availability undetermined, adding to pool 2012-10-03 16:16:07,166 WARNING: modinfo for module nvidia_96_updates failed: ERROR: modinfo: could not find module nvidia_96_updates 2012-10-03 16:16:07,171 DEBUG: Instantiated Handler subclass __builtin__.NvidiaDriver96Updates from name NvidiaDriver96Updates 2012-10-03 16:16:07,171 DEBUG: nvidia.available: falling back to default 2012-10-03 16:16:07,188 DEBUG: XorgDriverHandler(nvidia_96_updates, nvidia-96-updates, None): Disabling as package video ABI xorg-video-abi-10 does not match X.org video ABI xorg-video-abi-11 2012-10-03 16:16:07,188 DEBUG: NVIDIA accelerated graphics driver (post-release updates) not available 2012-10-03 16:16:07,188 DEBUG: loading custom handler /usr/share/jockey/handlers/madwifi.py 2012-10-03 16:16:07,195 WARNING: modinfo for module ath_pci failed: ERROR: modinfo: could not find module ath_pci 2012-10-03 16:16:07,195 DEBUG: Instantiated Handler subclass __builtin__.MadwifiHandler from name MadwifiHandler 2012-10-03 16:16:07,196 DEBUG: Alternate Atheros "madwifi" driver availability undetermined, adding to pool 2012-10-03 16:16:07,196 DEBUG: loading custom handler /usr/share/jockey/handlers/sl_modem.py 2012-10-03 16:16:07,213 DEBUG: Instantiated Handler subclass __builtin__.SlModem from name SlModem 2012-10-03 16:16:07,234 DEBUG: Software modem not available 2012-10-03 16:16:07,234 DEBUG: loading custom handler /usr/share/jockey/handlers/broadcom_wl.py 2012-10-03 16:16:07,239 WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl 2012-10-03 16:16:07,277 DEBUG: Instantiated Handler subclass __builtin__.BroadcomWLHandler from name BroadcomWLHandler 2012-10-03 16:16:07,277 DEBUG: Broadcom STA wireless driver availability undetermined, adding to pool 2012-10-03 16:16:07,278 DEBUG: all custom handlers loaded 2012-10-03 16:16:07,278 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'pci:v00008086d000027D8sv00001043sd000082EAbc04sc03i00') 2012-10-03 16:16:07,568 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'snd_hda_intel'} 2012-10-03 16:16:07,699 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'snd_hda_intel', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,699 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'snd_hda_intel'} 2012-10-03 16:16:07,699 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'snd_hda_intel', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,699 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'input:b0000v0000p0000e0000-e0,5,kramlsfw6,') 2012-10-03 16:16:07,704 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'evbug'} 2012-10-03 16:16:07,704 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'evbug', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,704 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'pci:v00008086d000027DAsv00001043sd00008179bc0Csc05i00') 2012-10-03 16:16:07,707 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'i2c_i801'} 2012-10-03 16:16:07,707 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'i2c_i801', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,707 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'acpi:PNP0C01:') 2012-10-03 16:16:07,707 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'acpi:PNP0B00:') 2012-10-03 16:16:07,707 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'pci:v00001969d00001026sv00001043sd00008304bc02sc00i00') 2012-10-03 16:16:07,710 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'atl1e'} 2012-10-03 16:16:07,710 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'atl1e', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,710 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'input:b0003v04F2p0816e0111-e0,1,4,11,14,k71,72,73,74,75,77,79,7A,7B,7C,7D,7E,7F,80,81,82,83,84,85,86,87,88,89,8A,8C,8E,96,98,9E,9F,A1,A3,A4,A5,A6,AD,B0,B1,B2,B3,B4,B7,B8,B9,BA,BB,BC,BD,BE,BF,C0,C1,C2,F0,ram4,l0,1,2,sfw') 2012-10-03 16:16:07,711 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'evbug'} 2012-10-03 16:16:07,711 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'evbug', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,711 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'mac_hid'} 2012-10-03 16:16:07,711 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'mac_hid', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,711 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'platform:pcspkr') 2012-10-03 16:16:07,711 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'pcspkr'} 2012-10-03 16:16:07,711 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'pcspkr', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,712 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'snd_pcsp'} 2012-10-03 16:16:07,712 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'snd_pcsp', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,712 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'usb:v1D6Bp0001d0302dc09dsc00dp00ic09isc00ip00') 2012-10-03 16:16:07,724 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'input:b0019v0000p0001e0000-e0,1,k74,ramlsfw') 2012-10-03 16:16:07,724 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'evbug'} 2012-10-03 16:16:07,724 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'evbug', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,724 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'mac_hid'} 2012-10-03 16:16:07,724 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'mac_hid', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,724 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'acpi:PNP0C04:') 2012-10-03 16:16:07,724 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'platform:eisa') 2012-10-03 16:16:07,725 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'pci:v00008086d000027CCsv00001043sd00008179bc0Csc03i20') 2012-10-03 16:16:07,728 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'platform:Fixed MDIO bus') 2012-10-03 16:16:07,728 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'pci:v00008086d000029C0sv00001043sd000082B0bc06sc00i00') 2012-10-03 16:16:07,731 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'usb:v045Ep0766d0101dcEFdsc02dp01ic01isc01ip00') 2012-10-03 16:16:07,777 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'snd_usb_audio'} 2012-10-03 16:16:07,777 DEBUG: no corresponding handler available for {'driver_type': 'kernel_module', 'kernel_module': 'snd_usb_audio', 'jockey_handler': 'KernelModuleHandler'} 2012-10-03 16:16:07,777 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'acpi:PNP0F03:PNP0F13:') 2012-10-03 16:16:07,777 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'acpi:PNP0000:') 2012-10-03 16:16:07,777 DEBUG: querying driver db <jockey.detection.LocalKernelModulesDriverDB instance at 0xb7231a0c> about HardwareID('modalias', 'pci:v00001002d000095C5sv0000174Bsd0000E400bc03sc00i00') 2012-10-03 16:16:08,072 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'fglrx_updates', 'package': 'fglrx-updates'} 2012-10-03 16:16:08,133 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/i386-linux-gnu/mesa/ld.so.conf other target alt None other current alt None 2012-10-03 16:16:08,134 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:16:08,072 DEBUG: found match in handler pool xorg:fglrx_updates([FglrxDriverUpdate, nonfree, disabled] ATI/AMD proprietary FGLRX graphics driver (post-release updates)) 2012-10-03 16:16:08,136 WARNING: modinfo for module fglrx_updates failed: ERROR: modinfo: could not find module fglrx_updates 2012-10-03 16:16:08,147 DEBUG: fglrx.available: falling back to default 2012-10-03 16:16:08,173 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/i386-linux-gnu/mesa/ld.so.conf other target alt None other current alt None 2012-10-03 16:16:08,173 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:16:08,162 DEBUG: got handler xorg:fglrx_updates([FglrxDriverUpdate, nonfree, disabled] ATI/AMD proprietary FGLRX graphics driver (post-release updates)) 2012-10-03 16:16:08,173 DEBUG: searching handler for driver ID {'driver_type': 'kernel_module', 'kernel_module': 'fglrx', 'package': 'fglrx'} 2012-10-03 16:16:08,184 DEBUG: fglrx.enabled(fglrx): target_alt None current_alt /usr/lib/i386-linux-gnu/mesa/ld.so.conf other target alt None other current alt None 2012-10-03 16:16:08,184 DEBUG: fglrx is not the alternative in use 2012-10-03 16:16:08,173 DEBUG: found match in handler pool xorg:fglrx([FglrxDriver, nonfree, disabled] ATI/AMD proprietary FGLRX graphics driver) 2012-10-03 16:16:08,187 WARNING: modinfo for module fglrx failed: ERROR: modinfo: could not find module fglrx 2012-10-03 16:16:08,190 DEBUG: fglrx.available: falling back to default 2012-10-03 16:16:08,216 DEBUG: fglrx.enabled(fglrx): target_alt None current_alt /usr/lib/i386-linux-gnu/mesa/ld.so.conf other target alt None other current alt None . . . 2012-10-03 16:18:10,552 DEBUG: install progress initramfs-tools 62.500000 2012-10-03 16:18:22,249 DEBUG: install progress libc-bin 62.500000 2012-10-03 16:18:23,251 DEBUG: Selecting previously unselected package dkms. (Reading database ... 142496 files and directories currently installed.) Unpacking dkms (from .../dkms_2.2.0.3-1ubuntu3_all.deb) ... Selecting previously unselected package fakeroot. Unpacking fakeroot (from .../fakeroot_1.18.2-1_i386.deb) ... Selecting previously unselected package fglrx-updates. Unpacking fglrx-updates (from .../fglrx-updates_2%3a8.960-0ubuntu1.1_i386.deb) ... Selecting previously unselected package fglrx-amdcccle-updates. Unpacking fglrx-amdcccle-updates (from .../fglrx-amdcccle-updates_2%3a8.960-0ubuntu1.1_i386.deb) ... Processing triggers for man-db ... Processing triggers for ureadahead ... ureadahead will be reprofiled on next reboot dpkg: error processing libxss1 (--configure): package libxss1 is already installed and configured dpkg: error processing chromium-codecs-ffmpeg (--configure): package chromium-codecs-ffmpeg is already installed and configured dpkg: error processing chromium-browser (--configure): package chromium-browser is already installed and configured dpkg: error processing chromium-browser-l10n (--configure): package chromium-browser-l10n is already installed and configured Setting up dkms (2.2.0.3-1ubuntu3) ... No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already Setting up fakeroot (1.18.2-1) ... update-alternatives: using /usr/bin/fakeroot-sysv to provide /usr/bin/fakeroot (fakeroot) in auto mode. Setting up fglrx-updates (2:8.960-0ubuntu1.1) ... update-alternatives: using /usr/lib/fglrx/ld.so.conf to provide /etc/ld.so.conf.d/i386-linux-gnu_GL.conf (i386-linux-gnu_gl_conf) in auto mode. update-alternatives: warning: skip creation of /etc/OpenCL/vendors/amdocl64.icd because associated file /usr/lib/fglrx/etc/OpenCL/vendors/amdocl64.icd (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalcl.so because associated file /usr/lib32/fglrx/libaticalcl.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalrt.so because associated file /usr/lib32/fglrx/libaticalrt.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: using /usr/lib/fglrx/alt_ld.so.conf to provide /etc/ld.so.conf.d/x86_64-linux-gnu_GL.conf (x86_64-linux-gnu_gl_conf) in auto mode. update-initramfs: deferring update (trigger activated) Loading new fglrx-updates-8.960 DKMS files... First Installation: checking all kernels... Building only for 3.2.0-29-generic-pae Building for architecture i686 Building initial module for 3.2.0-29-generic-pae Done. fglrx_updates: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.2.0-29-generic-pae/updates/dkms/ depmod...... DKMS: install completed. update-initramfs: deferring update (trigger activated) Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Setting up fglrx-amdcccle-updates (2:8.960-0ubuntu1.1) ... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.2.0-29-generic-pae Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: libxss1 chromium-codecs-ffmpeg chromium-browser chromium-browser-l10n Error in function: SystemError: E:Sub-process /usr/bin/dpkg returned an error code (1) 2012-10-03 16:18:23,256 ERROR: Package failed to install: Selecting previously unselected package dkms. (Reading database ... 142496 files and directories currently installed.) Unpacking dkms (from .../dkms_2.2.0.3-1ubuntu3_all.deb) ... Selecting previously unselected package fakeroot. Unpacking fakeroot (from .../fakeroot_1.18.2-1_i386.deb) ... Selecting previously unselected package fglrx-updates. Unpacking fglrx-updates (from .../fglrx-updates_2%3a8.960-0ubuntu1.1_i386.deb) ... Selecting previously unselected package fglrx-amdcccle-updates. Unpacking fglrx-amdcccle-updates (from .../fglrx-amdcccle-updates_2%3a8.960-0ubuntu1.1_i386.deb) ... Processing triggers for man-db ... Processing triggers for ureadahead ... ureadahead will be reprofiled on next reboot dpkg: error processing libxss1 (--configure): package libxss1 is already installed and configured dpkg: error processing chromium-codecs-ffmpeg (--configure): package chromium-codecs-ffmpeg is already installed and configured dpkg: error processing chromium-browser (--configure): package chromium-browser is already installed and configured dpkg: error processing chromium-browser-l10n (--configure): package chromium-browser-l10n is already installed and configured Setting up dkms (2.2.0.3-1ubuntu3) ... No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already Setting up fakeroot (1.18.2-1) ... update-alternatives: using /usr/bin/fakeroot-sysv to provide /usr/bin/fakeroot (fakeroot) in auto mode. Setting up fglrx-updates (2:8.960-0ubuntu1.1) ... update-alternatives: using /usr/lib/fglrx/ld.so.conf to provide /etc/ld.so.conf.d/i386-linux-gnu_GL.conf (i386-linux-gnu_gl_conf) in auto mode. update-alternatives: warning: skip creation of /etc/OpenCL/vendors/amdocl64.icd because associated file /usr/lib/fglrx/etc/OpenCL/vendors/amdocl64.icd (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalcl.so because associated file /usr/lib32/fglrx/libaticalcl.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: warning: skip creation of /usr/lib32/libaticalrt.so because associated file /usr/lib32/fglrx/libaticalrt.so (of link group i386-linux-gnu_gl_conf) doesn't exist. update-alternatives: using /usr/lib/fglrx/alt_ld.so.conf to provide /etc/ld.so.conf.d/x86_64-linux-gnu_GL.conf (x86_64-linux-gnu_gl_conf) in auto mode. update-initramfs: deferring update (trigger activated) Loading new fglrx-updates-8.960 DKMS files... First Installation: checking all kernels... Building only for 3.2.0-29-generic-pae Building for architecture i686 Building initial module for 3.2.0-29-generic-pae Done. fglrx_updates: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.2.0-29-generic-pae/updates/dkms/ depmod...... DKMS: install completed. update-initramfs: deferring update (trigger activated) Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Setting up fglrx-amdcccle-updates (2:8.960-0ubuntu1.1) ... Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.2.0-29-generic-pae Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: libxss1 chromium-codecs-ffmpeg chromium-browser chromium-browser-l10n Error in function: SystemError: E:Sub-process /usr/bin/dpkg returned an error code (1) 2012-10-03 16:18:23,590 WARNING: /sys/module/fglrx_updates/drivers does not exist, cannot rebind fglrx_updates driver 2012-10-03 16:18:43,601 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:43,601 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:43,617 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:43,617 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:54,143 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,144 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:54,154 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,154 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:54,182 DEBUG: fglrx.enabled(fglrx): target_alt /usr/lib/fglrx/ld.so.conf current_alt /usr/lib/fglrx/ld.so.conf other target alt /usr/lib/fglrx/alt_ld.so.conf other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,182 DEBUG: XorgDriverHandler(%s, %s).enabled(): No X.org driver set, not checking 2012-10-03 16:18:54,215 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,215 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:54,229 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,229 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:54,268 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,268 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:54,279 DEBUG: fglrx.enabled(fglrx_updates): target_alt None current_alt /usr/lib/fglrx/ld.so.conf other target alt None other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,279 DEBUG: fglrx_updates is not the alternative in use 2012-10-03 16:18:54,298 DEBUG: fglrx.enabled(fglrx): target_alt /usr/lib/fglrx/ld.so.conf current_alt /usr/lib/fglrx/ld.so.conf other target alt /usr/lib/fglrx/alt_ld.so.conf other current alt /usr/lib/fglrx/alt_ld.so.conf 2012-10-03 16:18:54,298 DEBUG: XorgDriverHandler(%s, %s).enabled(): No X.org driver set, not checking 2012-10-03 16:18:57,828 DEBUG: Shutting down I don't know how to troubleshoot from looking at the log file, could somebody assist me with this please? You can download the log file at: https://www.dropbox.com/s/a59d2hyabo02q5z/jockey.log

    Read the article

  • Toshiba wireless is blocked

    - by zorrillo
    I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

    Read the article

  • Wireless driver activation problem in compaq c700 in ubuntu 9.04

    - by Fazil
    I am using ubuntu 9.04, i cant access my wireless driver, i activate the madwifi in administrationhardware drivers, but i could'nt activated the wireless too. when i type lspci i get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when i tried in windows i found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can i do for solving this problem.

    Read the article

  • Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

    - by Fazil
    I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

    Read the article

  • how to setup kismet.conf on Ubuntu

    - by Registered User
    I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

    Read the article

  • nokia cell phone not accepting IP from dnsmasq dhcp server

    - by samix
    Hello, I having problem connecting a NOkia cell phone to my home wifi network. The wifi network is provided by a wireless card in a machine running Debian Testing and 2.6.26-2-686 kernel. The cars is D-Link DWL-G520 working in ap mode and has WPA encryption enabled. The wireless network is provided by hostapd using madwifi driver. Windows and Mac machines work properly with this wifi network. When I try to get the Nokia phone to connect to the wifi network, I get these lines in my dnsmasq log (to see lines without wrapping, here is the pastebin link for convenience - http://pastebin.com/m466c8fd2): Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 IEEE 802.11: disassociated Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 IEEE 802.11: associated Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 RADIUS: starting accounting session 4AE664FA-00000036 Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 WPA: pairwise key handshake completed (WPA) Oct 27 13:25:21 red hostapd: ath0: STA 11:22:33:44:55:66 WPA: group key handshake completed (WPA) Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 Available DHCP range: 192.168.5.150 -- 192.168.5.199 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 DHCPDISCOVER(ath0) 0.0.0.0 11:22:33:44:55:66 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 DHCPOFFER(ath0) 192.168.5.21 11:22:33:44:55:66 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 requested options: 12:hostname, 6:dns-server, 15:domain-name, Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 requested options: 1:netmask, 3:router, 28:broadcast, 120:sip-server Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 tags: known, ath0 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 next server: 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 1 option: 53:message-type 02 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 54:server-identifier 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 51:lease-time 00:00:46:50 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 58:T1 00:00:23:28 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 59:T2 00:00:3d:86 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 1:netmask 255.255.255.0 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 28:broadcast 192.168.5.255 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 3:router 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 4 option: 6:dns-server 192.168.5.1 Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 8 option: 15:domain-name home.pvt Oct 27 13:25:21 red dnsmasq-dhcp[11451]: 3875439214 sent size: 3 option: 12:hostname NokiaCellPhone Anybody know the problem might be? If I switch off dnsmasq dhcp queries logging, i.e. if I decrease the verbosity of the log, all I see are two lines of DHCPDISCOVER(ath0) and DHCPOFFER(ath0) repeatedly in the log with no acceptance by the cell phone. It appears as though the phone is not accepting the dhcp offer. However, if I give the phone a static IP address in its configuration, it works properly on the wifi network. So it appears as though the problem is dhcp related. Hints? Suggestions? Installed stuff: $ dpkg -l dnsmasq hostap* | grep ^i ii dnsmasq 2.50-1 A small caching DNS proxy and DHCP/TFTP server ii dnsmasq-base 2.50-1 A small caching DNS proxy and DHCP/TFTP server ii hostapd 1:0.6.9-3 user space IEEE 802.11 AP and IEEE 802.1X/WPA/ Thanks. PS: Here is the DHCP tcp dump for more information (with mac addresses changed): $ sudo dhcpdump -i ath0 -h ^11:22:33:44:55:66 TIME: 2009-10-30 12:15:32.916 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 0 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:32.918 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 0 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:32.918 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 0 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:34.922 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 2 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:34.922 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 2 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:34.923 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 2 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:38.919 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 6 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:38.920 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 6 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:38.921 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: c3f93d53 SECS: 6 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:46.944 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: ccafe769 SECS: 14 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:46.944 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: ccafe769 SECS: 14 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 0.0.0.0 SIADDR: 0.0.0.0 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 1 (DHCPDISCOVER) OPTION: 50 ( 4) Request IP address 0.0.0.0 OPTION: 61 ( 7) Client-identifier 01:11:22:33:44:55:66 OPTION: 55 ( 7) Parameter Request List 12 (Host name) 6 (DNS server) 15 (Domainname) 1 (Subnet mask) 3 (Routers) 28 (Broadcast address) 120 (SIP Servers DHCP Option) OPTION: 57 ( 2) Maximum DHCP message size 576 TIME: 2009-10-30 12:15:46.945 IP: 192.168.5.1 (a:bb:cc:dd:ee:ff) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 2 (BOOTPREPLY) HTYPE: 1 (Ethernet) HLEN: 6 HOPS: 0 XID: ccafe769 SECS: 14 FLAGS: 7f80 CIADDR: 0.0.0.0 YIADDR: 192.168.5.21 SIADDR: 192.168.5.1 GIADDR: 0.0.0.0 CHADDR: 11:22:33:44:55:66:00:00:00:00:00:00:00:00:00:00 SNAME: . FNAME: . OPTION: 53 ( 1) DHCP message type 2 (DHCPOFFER) OPTION: 54 ( 4) Server identifier 192.168.5.1 OPTION: 51 ( 4) IP address leasetime 18000 (5h) OPTION: 58 ( 4) T1 9000 (2h30m) OPTION: 59 ( 4) T2 15750 (4h22m30s) OPTION: 1 ( 4) Subnet mask 255.255.255.0 OPTION: 28 ( 4) Broadcast address 192.168.5.255 OPTION: 3 ( 4) Routers 192.168.5.1 OPTION: 6 ( 4) DNS server 192.168.5.1 OPTION: 15 ( 8) Domainname home.pvt OPTION: 12 ( 3) Host name Nokia_E63 TIME: 2009-10-30 12:15:48.952 IP: 0.0.0.0 (1:22:33:44:55:66) 255.255.255.255 (ff:ff:ff:ff:ff:ff) OP: 1 (BOOTPREQUEST) HTYPE: 1 (Ethernet) HLEN: 6 ... and so on ...

    Read the article

1