Search Results

Search found 4 results on 1 pages for 'mrc'.

Page 1/1 | 1 

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• WLAN LED randomly blinking when there is no traffic

  - by mrc

  Hi, I've got a Linksys WUSB54GC WLAN USB interface (Ralink chipset) and I'm running Debian GNU/Linux 6.0. The LED very often randomly blinks although there is no traffic in the network. I checked this with Wireshark. Sometimes, but rarely, the LED stops blinking. The issue is present in Ubuntu and Fedora too. It was not present in Debian Lenny with Linux 2.6.28. I checked an old live cd with ubuntu 8.10 with kernel 2.6.27 and it was also OK. So I guess that's an issue with Linux kernel and its wireless driver or firmware. Has anybody observed a similar thing? Does anybody know how to help this annoying blinking? Thanks.

  Read the article

• QT- QImage and multi-threading problem.

  - by umanga

  Greetings all, Please refer to image at : http://i48.tinypic.com/316qb78.jpg We are developing an application to extract cell edges from MRC images from electron microscope. MRC file format stores volumetric pixel data (http://en.wikipedia.org/wiki/Voxel) and we simply use 3D char array(char***) to load and store data (gray scale values) from a MRC file. As shown in the image,there are 3 viewers to display XY,YZ and ZX planes respectively. Scrollbars on the top of the viewers use to change the image slice along an axis. Here is the steps we do when user changes the scrollbar position. 1) get the new scrollbar value.(this is the selected slice) 2) for the relavant plane (YZ,XY or ZX), generate (char* slice;) array for the selected slice by reading 3D char array (char***) 3) Create a new QImage* (Format_RGB888) and set pixel values by reading 'slice' (using img-setPixel(x,y,c);) 4) This new QImage* is painted in the paintEvent() method. We are going to execute "edge-detection" process in a seperate thread since it is an intensive process.During this process we need to draw detected curve (set of pixels) on top of above QImage*.(as a layer).This means we need to call drawPoint() methods outside the QT thread. Is it the best wayto use QImage for this case? What is the best way to execute QT drawing methods from another thread? thanks in advance,

  Read the article

• Using jQuery in WordPress plugin admin page?

  - by Volmar

  I have a strange problem that probably have a really simple explanation that i've just havn't found. I'm making a WordPress plugin and i want to use jQuery in my settings-page for the plugin. My JS functions look like this: jQuery(document).ready(function() { alert('load test'); //ADMIN FUNCTION $('#mrc_imp_img').click(function(){ alert("test"); }); //FRONT END FUNCTION $("ul.mrc li").hover(function() { $(this).find('p').fadeIn(); } , function() { $(this).find('p').fadeOut(); }); }); The "load test"-alert is being loaded when the document is ready so jquery is properly loaded. The front end function is being used on pages and that's working fine to. the problem is the admin function, it's not working at all. is there a speial way i have to write a .click()-function to get it to work on my settings-page for the wordpress plugin?

  Read the article

1