Search Results

Search found 20 results on 1 pages for 'netscreen'.

Page 1/1 | 1 

  • Cisco PIX to Juniper Netscreen Policy-based VPN fails Phase 2 Proposal

    - by elint
    I've followed the instructions to configure a VPN between a netscreen device and a Cisco PIX as directed by Cisco's [netscreen to PIX VPN]http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00801c4445.shtml article. The only differences are that I'm running PIX 6.3(5) and Juniper Netscreen 6.1.0r2.0 (Firewall+VPN). I followed both configurations exactly, and when I try to connect, the Juniper returns with: 2010-02-21 12:54:28 information IKE: Removed Phase 2 SAs after receiving a notification message. 2010-02-21 12:54:28 information IKE pix_public_IP: Received a notification message for DOI 1 14 NO-PROPOSAL-CHOSEN. 2010-02-21 12:54:28 information IKE pix_public_IP Phase 2: Initiated negotiations. On the Netscreen, I've created a Phase 2 Proposal called ToCorpOffice using DH Group#2, 3DES-CBC, and SHA-1, and when configuring the AutoKey IKE, I chose ToCorpOffice and removed all other transforms. I believe I've configured the same on the PIX with: sysopt connection permit-ipsec crypto ipsec transform-set mytrans esp-3des esp-sha-hmac crypto map mymap 10 ipsec-isakmp crypto map mymap 10 match address nonat crypto map mymap 10 set pfs group2 crypto map mymap 10 set peer netscreen_public_ip crypto map mymap 10 set transform-set mytrans crypto map mymap interface outside Saved that and rebooted, so here's the cryptomap info: PIX-FW1# show crypto map Crypto Map: "mymap" interfaces: { outside } Crypto Map "mymap" 10 ipsec-isakmp Peer = netscreen_public_ip access-list nonat; 1 elements access-list nonat line 1 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0 (hitcnt=0) Current peer: netscreen_public_ip Security association lifetime: 4608000 kilobytes/28800 seconds PFS (Y/N): Y DH group: group2 Transform sets={ mytrans, } PIX-FW1# Any idea why I'm getting a NO-PROPOSAL-CHOSEN error?

    Read the article

  • Change password via NetScreen remote

    - by Marcelo Cantos
    I'm using NetScreen remote to VPN from home. I recently changed my password at work, and now my home system keeps complaining, "Windows needs your current credentials to ensure network connectivity." I can't change the cached password for peanuts. I can't find an option in NetScreen remote to connect to the VPN before logging in, as suggested here.

    Read the article

  • Change password via NetScreen remote

    - by Marcelo Cantos
    I'm using NetScreen remote to VPN from home. I recently changed my password at work, and now my home system keeps complaining, "Windows needs your current credentials to ensure network connectivity." I can't change the cached password for peanuts. I can't find an option in NetScreen remote to connect to the VPN before logging in, as suggested here. How do I change the cached password?

    Read the article

  • Netscreen-Remote Equivalent On Linux

    - by mojah
    We're running a simple Juniper VPN tunnel (using Juniper SSG5's) for outside-network access, which works great for Windows PCs since they can connect using the supplied Netscreen-Remote VPN client. Has anyone successfully managed to get this working under Linux? There are several alternatives, but none seem to actually work. The following were tried, but failed: - http://www.prolixium.com/netscreenlinux - http://david.dw-perspective.org.uk/Juniper-Networks-SSL-VPN-Client-On-Linux.html The official version is no Linux Client will ever be developed by Juniper themselves, but perhaps other (open) software exists that has been found compatible to Juniper's VPN?

    Read the article

  • Juniper NetScreen NS-5GT traffic monitoring

    - by blah
    I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

    Read the article

  • Juniper NetScreen NS-5GT traffic monitoring

    - by blah
    I've done casual research into the subject and am truly dismayed at the lack of compatible tools for such a simple task. Maybe someone can provide assistance. We have a NetScreen NS-5GT in the office. I need to be able to get a glance of current traffic per endpoint -- I think the equivalent of 'get sessions' with byte counts/rates. I don't care about bars, graphs, and reports. Something as simple as a classic software firewall display would be perfect. I can't shell out money on something real like SolarWinds products, so a free solution is essential. I'm willing to do a little work but refuse to program something from scratch. It's not prudent right now for me to install a hub or otherwise mess around physically. There must be something out there I can use, maybe in combination. I don't believe I'm asking too much. Specific answers only please, e.g. monitoring software you know will actually work with this antiquated device. I've read about general approaches to the broader problem dozens of times already.

    Read the article

  • How can I expire non-active sessions on my Netscreen SSG140?

    - by David Mackintosh
    I have a Juniper Netscreen SSG-140. While experimenting with a VoIP service, I defined a custom policy that was to be used to permit the possible ports in use to be sent back to the VoIP server from systems connecting across the internet. Because I'd had problems in the past with VoIP systems getting broken when their UDP sessions were expired out faster than their keep-alives were generated, I set the timeout on this custom service to be 'never'. After much experimentation, I happened to notice that my session count on the firewall has grown from a couple thousand to over 36000. After discussion with the VoIP "expert", I set the timeout to be 30 minutes; however, all the sessions set up during the experimentation process are still there, more than 3 days later. Is there a way I can force these old sessions to get expired and removed from the session table, or am I looking at resetting my firewall? (Both firewalls, actually -- they are in a cluster.)

    Read the article

  • Routing for IPSec tunnel

    - by Emre A
    For Juniper NetScreen-NS25, I configured a site-to-site IPSec tunnnel. For the outside interface of remote site, I also needed to go through tunnel which has the same IP as IPSec gateway. Now, when I add static route to route that outside interface IP through tunnel while tunnel is up, there would be no problem at all but if the tunnel is down for some reason, it cannot be re-established as the routing for the IPSec gateway IP which is the same as outside interface IP is set to go through tunnel which it needed to re-etablish at that time. So, packets won't hit that IP. I tried adding another routing entry which has metric 2 through other gateway but it did'nt succeeded. So, what type of routing should I configure to reach that IP when tunnel is down. Thanks in advance.

    Read the article

  • Routing for IPSec tunnel

    - by Emre A
    Hello. For Juniper NetScreen-NS25, I configured a site-to-site IPSec tunnnel. For the outside interface of remote site, I also needed to go through tunnel which has the same IP as IPSec gateway. Now, when I add static route to route that outside interface IP through tunnel while tunnel is up, there would be no problem at all but if the tunnel is down for some reason, it cannot be re-established as the routing for the IPSec gateway IP which is the same as outside interface IP is set to go through tunnel which it needed to re-etablish at that time. So, packets won't hit that IP. I tried adding another routing entry which has metric 2 through other gateway but it did'nt succeeded. So, what type of routing should I configure to reach that IP when tunnel is down. Thanks in advance.

    Read the article

  • ScreenOS MIP selection for outbound connections

    - by David Mackintosh
    Given a ScreenOS 6.3.0 firewall with this configuration: unset flow reverse-route clear-text set interface "ethernet0/0" zone "Trust" set interface ethernet0/0 ip 192.168.1.1/24 set interface ethernet0/2 ip 10.0.0.1/24 set interface ethernet0/2 mip 10.9.9.10 host 192.168.1.10 netmask 255.255.255.255 vr trust-vr set interface ethernet0/2 mip 10.8.8.10 host 192.168.1.10 netmask 255.255.255.255 vr trust-vr set route 0.0.0.0/0 interface ethernet0/2 gateway 10.0.0.254 ... (and assuming appropriate policies) is there a way to control which MIP the firewall selects for outbound connections initiated by 192.168.1.10? (presumably because I want the upstream 10.0.0.254 to do different things with the packet depending on what its source IP is). Update: OK, my scenario is this: I have two ISP uplinks, each giving me a different IP space. Each ISP will only route the IP space they have assigned me. So in order for the server to be reachable by both ISPs, I need two MIPs for the same server, one on each interface. Inbound traffic will work fine with the 'unset flow reverse-route clear-text' option in use. But for outbound (think an email server sending a message) I need a way to select an appropriate MIP depending on which outbound link I want the system to use, and I want this to be resiliant so that if the link the firewall prefers goes down overnight I don't have to manually flip something to keep the mail flowing. Basically I'm trying to avoid having to buy a link-balancer appliance (or two since I'll need a cluster). Is there a way to do this?

    Read the article

  • Net Screen manager setup

    - by Codezy
    I'm having an issue with our NSMExpress box. I'm trying to manage all our devices, range from ns5gt to ssg320m, and some of those devices have addresses assigned by dhcp from the ISP (like pppoe or dsl). The addresses are actually static but we have the register the MAC address in order to get this address. I can actually add the device in NSM except the IP that's on the untrust side isn't imported in as it's dynamic. Because of this I cannot change many options that pertian to the untrust interface as there is no IP. I've talked to JTAC on this and they didn't know if there was a way to do this or not but then they stated that Tim Hortons does this so I'm confused on how to get this working. Maybe i'm just missing something as I imagine that other people must be doing this as well. Any assistance is appreciated! Furthermore when I import a device this is the message I get: Warnings: Interface ethernet0/0 is a pppoe/dhcp/pppoa client and its ip is NOT IMPORTED because it may be dynamic.

    Read the article

  • How should I set up my Hyper-V server and network topology?

    - by Daniel Waechter
    This is my first time setting up either Hyper-V or Windows 2008, so please bear with me. I am setting up a pretty decent server running Windows Server 2008 R2 to be a remote (colocated) Hyper-V host. It will be hosting Linux and Windows VMs, initially for developers to use but eventually also to do some web hosting and other tasks. Currently I have two VMs, one Windows and one Ubuntu Linux, running pretty well, and I plan to clone them for future use. Right now I'm considering the best ways to configure developer and administrator access to the server once it is moved into the colocation facility, and I'm seeking advice on that. My thought is to set up a VPN for access to certain features of the VMs on the server, but I have a few different options for going about this: Connect the server to an existing hardware firewall (an old-ish Netscreen 5-GT) that can create a VPN and map external IPs to the VMs, which will have their own IPs exposed through the virtual interface. One problem with this choice is that I'm the only one trained on the Netscreen, and its interface is a bit baroque, so others may have difficulty maintaining it. Advantage is that I already know how to do it, and I know it will do what I need. Connect the server directly to the network and configure the Windows 2008 firewall to restrict access to the VMs and set up a VPN. I haven't done this before, so it will have a learning curve, but I'm willing to learn if this option is better long-term than the Netscreen. Another advantage is that I won't have to train anyone on the Netscreen interface. Still, I'm not certain if the capabilities of the Windows software firewall as far as creating VPNs, setting up rules for external access to certain ports on the IPs of Hyper-V servers, etc. Will it be sufficient for my needs and easy enough to set up / maintain? Anything else? What are the limitations of my approaches? What are the best practices / what has worked well for you? Remember that I need to set up developer access as well as consumer access to some services. Is a VPN even the right choice?

    Read the article

  • Shrew VPN Client gives default route- changing the policy stops me from accessing VPN network

    - by Lock
    I am using the shrew client to connect to what I believe is a Netscreen VPN. Now, when connected, the client adds the VPN as the default route. I do not want this- there is only 1 network behind the VPN that I need to access. I found that with the shrew client, you can change the "Policy" settings on the connection, and can add your own networks in that should tunnel over the VPN. I do this, and add my network in, but when I connect the VPN, I get nothing. Can't access the network. Any idea why this would be? I can see my network in the routing table, and its correctly pointing to the correct gateway. A traceroute shows all time-outs, so I can't be 100% sure that it is trying to tunnel over the VPN. Any idea how I can troubleshoot this?

    Read the article

  • What's required to enable communication between two IP ranges located behind one switch?

    - by Eric3
    Within our co-located networking closet, we have control over two ranges of 254 addresses, e.g. 64.123.45.0/24 and 65.234.56.0/24. The problem is, if a host has only one IP address, or a block of addresses in only one range, it can't contact any of the addresses in the other subnet. All of our hosts use our hosting provider's respective gateway, e.g. 64.123.45.1 or 65.234.56.1 A host on the 64.123.45.0/24 range can contact the 65.234.56.1 gateway and vice-versa Everything in our closet is connected to an HP ProCurve 2810 (a Layer 2-only switch), which connects through a Juniper NetScreen-25 firewall to the outside world What can I do to enable communication between the two ranges? Is there some settings I can change, or do I need better networking equipment?

    Read the article

  • How two use 2 subnets on one network

    - by BGuy2010
    I have some servers at a colocation. They've given us an IP range,subnet,and gateway. Now we have run out of IP's and they've given us a new range of IP's but with a different subnet and gateway. We have a Juniper NetScreen firewall and a load balancer, and I am not sure how to proceed in order to be able to use these new IPS that are on a different subnet. Do I need to setup a new VLAN? on our firewall? I tried adding one of the new IP's on one of our servers, with the new subnet and gateway. I could ping the alternate gateway, but could not ping the assigned IP from outside or from inside.

    Read the article

  • Access router set up as a bridge behind another router

    - by Alari Truuts
    I have a problem my ISP is refusing to help me with, even though they put up the whole system. Specifications: There's a Thomson TG784 router through which the internet comes in to the building, Behind that (for some reason) is a Juniper NetScreen 5XT - 105 Firewall/Router? which leads to an AMX nxa-enet24 switch that carries the connections all over the building and a series of Apple AirPorts for wifi. Problem: The first router (Thomson) is required for ipTV (by Elion). The tv or ipTV box has to be connected straight to the Thomson router. My service provider cannot see the Thomson router from their side, but see the Juniper, so we might think the Thomson has been configured as a bridge. I need a way to access the Thomson router and see it's configurations, because currently, when connecting a Samsung tv to that router (with elion app for ipTV viewing) or even a computer, it cannot access the internet and even if it could, it would update the Thomson router software, losing it's configurations which I need to preserve. I'm unable to find out the Thomson routers ip address to connect to it, and when directly conencting with a cat5 cable, it doesn't give me an ip address. Hope someone can show me the correct direction for solving my issue. Thank you all for reading, and I appreciate any help, Alari Truuts

    Read the article

  • iptables DNS resolution

    - by Favolas
    I have a virtual machine with Fedora 19 acting as a router. This machine as an interface (p8p1) with the IP 172.16.1.254 that is connected to another machine (IP 172.16.1.1) that's simulating the external network. I've installed snort 2.9.2.2, applied the snortsam-2.9.2.2.diff.gz patch and installed snortsam 2.70 on the routermachine In snort.conf besides altering some RULE_PATH I believe I've only added the following line to the file. output alert_fwsam: 127.0.0.1:898/password After doing this two comands: ifconfig p8p1 promisc /usr/local/snort/bin/snort -v -i p8p1 If I ping from the external network to the router IP, I can see the info about the pings. One of the rules that I have is icmp-info.rules that as this single line: alert icmp $EXTERNAL_NET any -> $HOME_NET any (msg:"ICMP-INFO Echo Reply"; icode:0; itype:0; classtype:misc-activity; sid:408; rev:6;fwsam: src, 5 minutes;) snortsam.conf as this data: defaultkey password accept localhost keyinterval 30 minutes dontblock 192.168.1.1 # rede local rollbackhosts 50 rollbackthreshold 20 / 30 secs rollbacksleeptime 1 minute logfile /var/log/snort/snortsam.log loglevel 3 daemon nothreads # linha importante para gerar os bloqueios via iptables iptables p8p1 LOG bindip 127.0.0.1 Now I run this command: /usr/local/snort/bin/snort -u snort -i p8p1 -c /etc/snort/snort.conf -l /var/log/snort -Dq Terminal gives this message: Spawning daemon child... My daemon child 2080 lives... Daemon parent exiting (0) and when I runsnortsam in terminal i got this: SnortSam, v 2.70. Copyright (c) 2001-2009 Frank Knobbe . All rights reserved. Plugin 'fwsam': v 2.5, by Frank Knobbe Plugin 'fwexec': v 2.7, by Frank Knobbe Plugin 'pix': v 2.9, by Frank Knobbe Plugin 'ciscoacl': v 2.12, by Ali Basel <[email protected]> Plugin 'cisconullroute': v 2.5, by Frank Knobbe Plugin 'cisconullroute2': v 2.2, by Wouter de Jong <[email protected]> Plugin 'netscreen': v 2.10, by Frank Knobbe Plugin 'ipchains': v 2.8, by Hector A. Paterno <[email protected]> Plugin 'iptables': v 2.9, by Fabrizio Tivano <[email protected]>, Luis Marichal <[email protected]> Plugin 'ebtables': v 2.4, by Bruno Scatolin <[email protected]> Plugin 'watchguard': v 2.7, by Thomas Maier <[email protected]> Plugin 'email': v 2.12, by Frank Knobbe Plugin 'email-blocks-only': v 2.12, by Frank Knobbe Plugin 'snmpinterfacedown': v 2.3, by Ali BASEL <[email protected]> Plugin 'forward': v 2.8, by Frank Knobbe Parsing config file /etc/snortsam.conf... Linking plugin 'iptables'... Checking for existing state file "/var/db/snortsam.state". Found. Reading state file. Starting to listen for Snort alerts. and snortsam.log as an entry like this 2013/10/25, 10:15:17, -, 1, snortsam, Starting to listen for Snort alerts. Now, from the external machine I do ping 172.16.1.254 and it starts showing the info and an alert file is created in /var/log/snort/ that as the info about the PINGS. Something like: [**] [1:408:6] ICMP-INFO Echo Reply [**] [Classification: Misc activity] [Priority: 3] 10/25-10:35:16.061319 172.16.1.254 -> 172.16.1.1 ICMP TTL:64 TOS:0x0 ID:38720 IpLen:20 DgmLen:84 Type:0 Code:0 ID:1389 Seq:1 ECHO REPLY Also, if I run instead /usr/local/snort/bin/snort snort -v -i p8p1 i got this message: Running in packet dump mode --== Initializing Snort ==-- Initializing Output Plugins! Snort BPF option: snort pcap DAQ configured to passive. The DAQ version does not support reload. Acquiring network traffic from "p8p1". ERROR: Can't set DAQ BPF filter to 'snort' (pcap_daq_set_filter: pcap_compile: syntax error)! Fatal Error, Quitting.. So, this are my questions: Shouldn't snortsam block the PING? Is that DAQ error causing the problem? If so, How can I solve it?

    Read the article

  • Juniper SSG-5 subinterface vlan routing to the internet

    - by catfish
    I'm unable to get a brand new Juniper SSG-5 with latest 6.3.0r05 firmware routing to the internet from a subinterface I created on bgroup0 setup as vlan2 (bgroup0.1 on "wifi" zone). When connected on the default vlan it gets on the internet just fine. When I switch to vlan2 I'm unable to get to the internet. I am able to get the correct ip address (10.150.0.0/24) from dhcp, able to get to the juniper management page, etc but nothing past the firewall, can't ping 4.2.2.2 or the internet gateway. Even setting up logging on the wifi-to-untrust policy and it does shows the attempts (it's it's timeouts). 172.31.16.0/24 is the untrusted lan, it's already nat'ed but works fine for testing. Can ping this ip from the default vlan but not from vlan2 192.168.1.0/24 is the trusted main lan 10.150.0.0/24 is the wifi isolated lan on vlan2 The idea is to setup an AP with lan and guest access (AP supports multiple ssid's on different vlans). I know I can setup the juniper to use different ports for the wifi lan and use their procurve switch to do the vlan separation, but I never used vlan'ing on a Juniper firewall and I would like to try it out this way. Here is the complete config file: unset key protection enable set clock timezone -5 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "xxxxxxxxxxxxxxxx" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone id 100 "Wifi" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst unset zone "Wifi" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Untrust" set interface "bgroup0" zone "Trust" set interface "bgroup0.1" tag 2 zone "Wifi" set interface "bgroup1" zone "DMZ" set interface bgroup0 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup0 port ethernet0/5 set interface bgroup0 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 172.31.16.243/24 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup0.1 ip 10.150.0.1/24 set interface bgroup0.1 nat set interface bgroup0.1 mtu 1500 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup0.1 ip manageable set interface ethernet0/0 manage ping set interface ethernet0/1 manage ping set interface bgroup0.1 manage ping set interface bgroup0.1 manage telnet set interface bgroup0.1 manage web unset interface bgroup1 manage ping set interface bgroup0 dhcp server service set interface bgroup0.1 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup0.1 dhcp server enable set interface bgroup0 dhcp server option gateway 192.168.1.1 set interface bgroup0 dhcp server option netmask 255.255.255.0 set interface bgroup0 dhcp server option dns1 8.8.8.8 set interface bgroup0.1 dhcp server option lease 1440 set interface bgroup0.1 dhcp server option gateway 10.150.0.1 set interface bgroup0.1 dhcp server option netmask 255.255.255.0 set interface bgroup0.1 dhcp server option dns1 8.8.8.8 set interface bgroup0 dhcp server ip 192.168.1.33 to 192.168.1.126 set interface bgroup0.1 dhcp server ip 10.150.0.50 to 10.150.0.100 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup0.1 dhcp server config next-server-ip set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow no-tcp-seq-check set flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Wifi" to "Untrust" "Any" "Any" "ANY" permit log set policy id 2 exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set snmpv3 local-engine id "0162122009006149" set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route set route 0.0.0.0/0 interface ethernet0/0 gateway 172.31.16.1 exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

    Read the article

  • help setting up an IPSEC vpn from my linux box

    - by robthewolf
    I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

    Read the article

  • Allowing connections initiated from outside

    - by Mark S. Rasmussen
    I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

    Read the article

1