Search Results

Search found 767 results on 31 pages for '4k sectors'.

Page 10/31 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• Disk is spinning down each minute, unable to disable it

  - by lzap

  I played with spindown and APM settings of my Samsung discs and now they spin down every minute. I want to disable it, but it seems it does not accept any of the spindown time or APM values. Nothing works, it's all the same. Please help what values should be proper for it. I do not want it to spin down at all. /dev/sda: ATA device, with non-removable media Model Number: SAMSUNG HD154UI Serial Number: S1Y6J1KZ206527 Firmware Revision: 1AG01118 Standards: Used: ATA-8-ACS revision 3b Supported: 7 6 5 4 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 2930277168 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 1430799 MBytes device size with M = 1000*1000: 1500301 MBytes (1500 GB) cache/buffer size = unknown Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 udma7 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test Media Card Pass-Through * General Purpose Logging feature set * 64-bit World wide name * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * NCQ priority information DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Long Sector Access (AC1) * SCT LBA Segment Access (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 326min for SECURITY ERASE UNIT. 326min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 50024e900300cca3 NAA : 5 IEEE OUI : 0024e9 Unique ID : 00300cca3 Checksum: correct I have the very same disc which I did not "tuned" and it does not spin. But I do not know where to read the settings from. The hdparm only shows this: Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 Edit: It seems the issue was tuned daemon in RHEL6. It was too aggressive, I turned off disc tuning and it seems they are no longer spinning down.

  Read the article

• How to correctly partition usb flash drive and which filesystem to choose considering wear leveling?

  - by random1

  Two problems. First one: how to partition the flash drive? I shouldn't need to do this, but I'm no longer sure if my partition is properly aligned since I was forced to delete and create a new partition table after gparted complained when I tried to format the drive from FAT to ext4. The naive answer would be to say "just use default and everything is going to be alright". However if you read the following links you'll know things are not that simple: https://lwn.net/Articles/428584/ and http://linux-howto-guide.blogspot.com/2009/10/increase-usb-flash-drive-write-speed.html Then there is also the issue of cylinders, heads and sectors. Currently I get this: $sfdisk -l -uM /dev/sdd Disk /dev/sdd: 30147 cylinders, 64 heads, 32 sectors/track Warning: The partition table looks like it was made for C/H/S=*/255/63 (instead of 30147/64/32). For this listing I'll assume that geometry. Units = mebibytes of 1048576 bytes, blocks of 1024 bytes, counting from 0 Device Boot Start End MiB #blocks Id System /dev/sdd1 1 30146 30146 30869504 83 Linux $fdisk -l /dev/sdd Disk /dev/sdd: 31.6 GB, 31611420672 bytes 255 heads, 63 sectors/track, 3843 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00010c28 So from my current understanding I should align partitions at 4 MiB (currently it's at 1 MiB). But I still don't know how to set the heads and sectors properly for my device. Second problem: file system. From the benchmarks I saw ext4 provides the best performance, however there is the issue of wear leveling. How can I know that my Transcend JetFlash 700's microcontroller provides for wear leveling? Or will I just be killing my drive faster? I've seen a lot of posts on the web saying don't worry the newer drives already take care of that. But I've never seen a single piece of backed evidence of that and at some point people start mixing SSD with USB flash drives technology. The safe option would be to go for ext2, however a serious of tests that I performed showed horrible performance!!! These values are from a real scenario and not some synthetic test: 42 files: 3,429,415,284 bytes copied to flash drive original fat32: 15.1 MiB/s ext4 after new partition table: 10.2 MiB/s ext2 after new partition table: 1.9 MiB/s Please read the links that I posted above before answering. I would also be interested in answers backed up with some references because a lot is said and re-said but then it lacks facts. Thank you for the help.

  Read the article

• Error 5 partition table invalid or corrupt

  - by Clodoaldo

  I'm trying to add a second SSD to a Centos 6 system. But I get the Error 5 partition table invalid or corrupt at boot. The system already has a single SSD (sdb) and a pair of HDDs (sd{a,c}) in a RAID 1 array from where it boots. It is as if the new SSD assumes one of the devices of the RAID array. Is it? How to avoid that or rearrange the setup? # cat fstab UUID=967b4035-782d-4c66-b22f-50244fe970ca / ext4 defaults 1 1 UUID=86fd06e9-cdc9-4166-ba9f-c237cfc43e02 /boot ext4 defaults 1 2 UUID=72552a7a-d8ae-4f0a-8917-b75a6239ce9f /ssd ext4 discard,relatime 1 2 UUID=8000e5e6-caa2-4765-94f8-9caeb2bda26e swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 # ll /dev/disk/by-id/ total 0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:0 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:1 -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:2 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a04d7241:8da6023e:f9004352:107a923a -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a22c43b9:f1954990:d3ddda5e:f9aff3c9 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-f403a2d0:447803b5:66edba73:569f8305 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c500383621ff -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c5003838b2e7 -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5e83a97f592139d6 -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5e83a97f592139d6-part1 -> ../../sdb1 # fdisk -l Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x79298ec9 Device Boot Start End Blocks Id System /dev/sdb1 1 14594 117219328 83 Linux Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d99de Device Boot Start End Blocks Id System /dev/sdc1 1 1275 10240000 fd Linux raid autodetect /dev/sdc2 * 1275 1339 512000 fd Linux raid autodetect /dev/sdc3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b3327 Device Boot Start End Blocks Id System /dev/sda1 1 1275 10240000 fd Linux raid autodetect /dev/sda2 * 1275 1339 512000 fd Linux raid autodetect /dev/sda3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/md0: 10.5 GB, 10484641792 bytes 2 heads, 4 sectors/track, 2559727 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md2: 489.1 GB, 489095557120 bytes 2 heads, 4 sectors/track, 119408095 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 524 MB, 524275712 bytes 2 heads, 4 sectors/track, 127997 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table # cat /etc/grub.conf default=0 timeout=5 splashimage=(hd2,1)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.32-220.17.1.el6.x86_64) root (hd2,1) kernel /vmlinuz-2.6.32-220.17.1.el6.x86_64 ro root=UUID=967b4035-782d-4c66-b22f-50244fe970ca rd_MD_UUID=f403a2d0:447803b5:66edba73:569f8305 rd_MD_UUID=a22c43b9:f1954990:d3ddda5e:f9aff3c9 rd_NO_LUKS rd_NO_LVM rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=br-abnt2 crashkernel=auto rhgb quiet initrd /initramfs-2.6.32-220.17.1.el6.x86_64.img

  Read the article

• Error 22 no such partition on adding a SSD

  - by Clodoaldo

  I'm trying to add a second SSD to a Centos 6 system. But I get the error 22 no such partition at boot. The system already has a single SSD (sdb) and a pair of HDDs (sd{a,c}) in a RAID 1 array from where it boots. It is as if the new SSD assumes one of the devices of the RAID array. Is it? How to avoid that or rearrange the setup? # cat fstab UUID=967b4035-782d-4c66-b22f-50244fe970ca / ext4 defaults 1 1 UUID=86fd06e9-cdc9-4166-ba9f-c237cfc43e02 /boot ext4 defaults 1 2 UUID=72552a7a-d8ae-4f0a-8917-b75a6239ce9f /ssd ext4 discard,relatime 1 2 UUID=8000e5e6-caa2-4765-94f8-9caeb2bda26e swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 # ll /dev/disk/by-id/ total 0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:0 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:1 -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:2 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a04d7241:8da6023e:f9004352:107a923a -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a22c43b9:f1954990:d3ddda5e:f9aff3c9 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-f403a2d0:447803b5:66edba73:569f8305 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c500383621ff -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c5003838b2e7 -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5e83a97f592139d6 -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5e83a97f592139d6-part1 -> ../../sdb1 # fdisk -l Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x79298ec9 Device Boot Start End Blocks Id System /dev/sdb1 1 14594 117219328 83 Linux Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d99de Device Boot Start End Blocks Id System /dev/sdc1 1 1275 10240000 fd Linux raid autodetect /dev/sdc2 * 1275 1339 512000 fd Linux raid autodetect /dev/sdc3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b3327 Device Boot Start End Blocks Id System /dev/sda1 1 1275 10240000 fd Linux raid autodetect /dev/sda2 * 1275 1339 512000 fd Linux raid autodetect /dev/sda3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/md0: 10.5 GB, 10484641792 bytes 2 heads, 4 sectors/track, 2559727 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md2: 489.1 GB, 489095557120 bytes 2 heads, 4 sectors/track, 119408095 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 524 MB, 524275712 bytes 2 heads, 4 sectors/track, 127997 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table # cat /etc/grub.conf default=0 timeout=5 splashimage=(hd2,1)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.32-220.17.1.el6.x86_64) root (hd2,1) kernel /vmlinuz-2.6.32-220.17.1.el6.x86_64 ro root=UUID=967b4035-782d-4c66-b22f-50244fe970ca rd_MD_UUID=f403a2d0:447803b5:66edba73:569f8305 rd_MD_UUID=a22c43b9:f1954990:d3ddda5e:f9aff3c9 rd_NO_LUKS rd_NO_LVM rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=br-abnt2 crashkernel=auto rhgb quiet initrd /initramfs-2.6.32-220.17.1.el6.x86_64.img

  Read the article

• USB hard drive not recognized

  - by user318772

  Until recently I was using the portable USB hard drive in my win 7 laptop and ubuntu laptop. Suddenly now none of the laptops recognize it. This is the message i get by doing lsusb... Bus 001 Device 004: ID 1058:1010 Western Digital Technologies, Inc. Elements External HDD Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 0b97:7762 O2 Micro, Inc. Oz776 SmartCard Reader Bus 003 Device 002: ID 0b97:7761 O2 Micro, Inc. Oz776 1.1 Hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub fdisk doesn't show the external hard drive Disk /dev/sda: 80.0 GB, 80026361856 bytes 255 heads, 63 sectors/track, 9729 cylinders, total 156301488 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0004a743 Device Boot Start End Blocks Id System /dev/sda1 * 2048 152111103 76054528 83 Linux /dev/sda2 152113150 156301311 2094081 5 Extended /dev/sda5 152113152 156301311 2094080 82 Linux swap / Solaris when i do testdisk TestDisk 6.14, Data Recovery Utility, July 2013 Christophe GRENIER <[email protected]> http://www.cgsecurity.org TestDisk is free software, and comes with ABSOLUTELY NO WARRANTY. Select a media (use Arrow keys, then press Enter): >Disk /dev/sda - 80 GB / 74 GiB - ST980825AS Disk /dev/sdb - 2199 GB / 2048 GiB testdisk-> Intel->analyse I get partition error Disk /dev/sdb - 2199 GB / 2048 GiB - CHS 2097152 64 32 Current partition structure: Partition Start End Size in sectors Partition: Read error Here is the output of dmesg [11948.549171] Add. Sense: Invalid command operation code [11948.549177] sd 2:0:0:0: [sdb] CDB: [11948.549181] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.550489] sd 2:0:0:0: [sdb] Invalid command failure [11948.550495] sd 2:0:0:0: [sdb] [11948.550499] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.550505] sd 2:0:0:0: [sdb] [11948.550508] Sense Key : Illegal Request [current] [11948.550514] Info fld=0x0 [11948.550519] sd 2:0:0:0: [sdb] [11948.550525] Add. Sense: Invalid command operation code [11948.550531] sd 2:0:0:0: [sdb] CDB: [11948.550534] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 [11948.551870] sd 2:0:0:0: [sdb] Invalid command failure [11948.551876] sd 2:0:0:0: [sdb] [11948.551880] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [11948.551885] sd 2:0:0:0: [sdb] [11948.551888] Sense Key : Illegal Request [current] [11948.551895] Info fld=0x0 [11948.551900] sd 2:0:0:0: [sdb] [11948.551905] Add. Sense: Invalid command operation code [11948.551911] sd 2:0:0:0: [sdb] CDB: [11948.551914] Read(16): 88 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 If possible i want to retrive at least some data from this hard drive. If thats not possible I would like to format it and use it. Any help will be greatly appreciated Thanks

  Read the article

• Stable random color algorithm

  - by Olmo

  Here we have an interesting real-world algorithm requirement involving colors. 1) Nice random colors: In ordeeing to draw a beautifull chart (i.e: pie chart) we need to pick a random set of Colors that: a) are different enought b) Play nicely Doesnt Look hard. For example u fix bright and saturation and divide hue in steps of 360/Num_sectors 2) Stable: given Pie1 with sectors with labes ('A','B','C') and Pie2 with sector with labels ('B','C','D'), will be nice if color('B',pie1)= color('B',pie2) and the same for 'C' and so on, so people don't get crazy when seeing similar updated charts, even if some sectors appear some dissapeared or the number of sectors changed. The label is the only stable thing. 3) hard-coded colors: the algorithm allows hardcoded label-color relationships as an input but stills doing a good work (1 & 2) for the rest of free labels. I think this algorithm, even if it looks quite ad-hoc, will be usefull in more then one situation. Any ideas?

  Read the article

• LSI 9285-8e and Supermicro SC837E26-RJBOD1 duplicate enclosure ID and slot numbers

  - by Andy Shinn

  I am working with 2 x Supermicro SC837E26-RJBOD1 chassis connected to a single LSI 9285-8e card in a Supermicro 1U host. There are 28 drives in each chassis for a total of 56 drives in 28 RAID1 mirrors. The problem I am running in to is that there are duplicate slots for the 2 chassis (the slots list twice and only go from 0 to 27). All the drives also show the same enclosure ID (ID 36). However, MegaCLI -encinfo lists the 2 enclosures correctly (ID 36 and ID 65). My question is, why would this happen? Is there an option I am missing to use 2 enclosures effectively? This is blocking me rebuilding a drive that failed in slot 11 since I can only specify enclosure and slot as parameters to replace a drive. When I do this, it picks the wrong slot 11 (device ID 46 instead of device ID 19). Adapter #1 is the LSI 9285-8e, adapter #0 (which I removed due to space limitations) is the onboard LSI. Adapter information: Adapter #1 ============================================================================== Versions ================ Product Name : LSI MegaRAID SAS 9285-8e Serial No : SV12704804 FW Package Build: 23.1.1-0004 Mfg. Data ================ Mfg. Date : 06/30/11 Rework Date : 00/00/00 Revision No : 00A Battery FRU : N/A Image Versions in Flash: ================ BIOS Version : 5.25.00_4.11.05.00_0x05040000 WebBIOS Version : 6.1-20-e_20-Rel Preboot CLI Version: 05.01-04:#%00001 FW Version : 3.140.15-1320 NVDATA Version : 2.1106.03-0051 Boot Block Version : 2.04.00.00-0001 BOOT Version : 06.253.57.219 Pending Images in Flash ================ None PCI Info ================ Vendor Id : 1000 Device Id : 005b SubVendorId : 1000 SubDeviceId : 9285 Host Interface : PCIE ChipRevision : B0 Number of Frontend Port: 0 Device Interface : PCIE Number of Backend Port: 8 Port : Address 0 5003048000ee8e7f 1 5003048000ee8a7f 2 0000000000000000 3 0000000000000000 4 0000000000000000 5 0000000000000000 6 0000000000000000 7 0000000000000000 HW Configuration ================ SAS Address : 500605b0038f9210 BBU : Present Alarm : Present NVRAM : Present Serial Debugger : Present Memory : Present Flash : Present Memory Size : 1024MB TPM : Absent On board Expander: Absent Upgrade Key : Absent Temperature sensor for ROC : Present Temperature sensor for controller : Absent ROC temperature : 70 degree Celcius Settings ================ Current Time : 18:24:36 3/13, 2012 Predictive Fail Poll Interval : 300sec Interrupt Throttle Active Count : 16 Interrupt Throttle Completion : 50us Rebuild Rate : 30% PR Rate : 30% BGI Rate : 30% Check Consistency Rate : 30% Reconstruction Rate : 30% Cache Flush Interval : 4s Max Drives to Spinup at One Time : 2 Delay Among Spinup Groups : 12s Physical Drive Coercion Mode : Disabled Cluster Mode : Disabled Alarm : Enabled Auto Rebuild : Enabled Battery Warning : Enabled Ecc Bucket Size : 15 Ecc Bucket Leak Rate : 1440 Minutes Restore HotSpare on Insertion : Disabled Expose Enclosure Devices : Enabled Maintain PD Fail History : Enabled Host Request Reordering : Enabled Auto Detect BackPlane Enabled : SGPIO/i2c SEP Load Balance Mode : Auto Use FDE Only : No Security Key Assigned : No Security Key Failed : No Security Key Not Backedup : No Default LD PowerSave Policy : Controller Defined Maximum number of direct attached drives to spin up in 1 min : 10 Any Offline VD Cache Preserved : No Allow Boot with Preserved Cache : No Disable Online Controller Reset : No PFK in NVRAM : No Use disk activity for locate : No Capabilities ================ RAID Level Supported : RAID0, RAID1, RAID5, RAID6, RAID00, RAID10, RAID50, RAID60, PRL 11, PRL 11 with spanning, SRL 3 supported, PRL11-RLQ0 DDF layout with no span, PRL11-RLQ0 DDF layout with span Supported Drives : SAS, SATA Allowed Mixing: Mix in Enclosure Allowed Mix of SAS/SATA of HDD type in VD Allowed Status ================ ECC Bucket Count : 0 Limitations ================ Max Arms Per VD : 32 Max Spans Per VD : 8 Max Arrays : 128 Max Number of VDs : 64 Max Parallel Commands : 1008 Max SGE Count : 60 Max Data Transfer Size : 8192 sectors Max Strips PerIO : 42 Max LD per array : 16 Min Strip Size : 8 KB Max Strip Size : 1.0 MB Max Configurable CacheCade Size: 0 GB Current Size of CacheCade : 0 GB Current Size of FW Cache : 887 MB Device Present ================ Virtual Drives : 28 Degraded : 0 Offline : 0 Physical Devices : 59 Disks : 56 Critical Disks : 0 Failed Disks : 0 Supported Adapter Operations ================ Rebuild Rate : Yes CC Rate : Yes BGI Rate : Yes Reconstruct Rate : Yes Patrol Read Rate : Yes Alarm Control : Yes Cluster Support : No BBU : No Spanning : Yes Dedicated Hot Spare : Yes Revertible Hot Spares : Yes Foreign Config Import : Yes Self Diagnostic : Yes Allow Mixed Redundancy on Array : No Global Hot Spares : Yes Deny SCSI Passthrough : No Deny SMP Passthrough : No Deny STP Passthrough : No Support Security : No Snapshot Enabled : No Support the OCE without adding drives : Yes Support PFK : Yes Support PI : No Support Boot Time PFK Change : Yes Disable Online PFK Change : No PFK TrailTime Remaining : 0 days 0 hours Support Shield State : Yes Block SSD Write Disk Cache Change: Yes Supported VD Operations ================ Read Policy : Yes Write Policy : Yes IO Policy : Yes Access Policy : Yes Disk Cache Policy : Yes Reconstruction : Yes Deny Locate : No Deny CC : No Allow Ctrl Encryption: No Enable LDBBM : No Support Breakmirror : No Power Savings : Yes Supported PD Operations ================ Force Online : Yes Force Offline : Yes Force Rebuild : Yes Deny Force Failed : No Deny Force Good/Bad : No Deny Missing Replace : No Deny Clear : No Deny Locate : No Support Temperature : Yes Disable Copyback : No Enable JBOD : No Enable Copyback on SMART : No Enable Copyback to SSD on SMART Error : Yes Enable SSD Patrol Read : No PR Correct Unconfigured Areas : Yes Enable Spin Down of UnConfigured Drives : Yes Disable Spin Down of hot spares : No Spin Down time : 30 T10 Power State : Yes Error Counters ================ Memory Correctable Errors : 0 Memory Uncorrectable Errors : 0 Cluster Information ================ Cluster Permitted : No Cluster Active : No Default Settings ================ Phy Polarity : 0 Phy PolaritySplit : 0 Background Rate : 30 Strip Size : 64kB Flush Time : 4 seconds Write Policy : WB Read Policy : Adaptive Cache When BBU Bad : Disabled Cached IO : No SMART Mode : Mode 6 Alarm Disable : Yes Coercion Mode : None ZCR Config : Unknown Dirty LED Shows Drive Activity : No BIOS Continue on Error : No Spin Down Mode : None Allowed Device Type : SAS/SATA Mix Allow Mix in Enclosure : Yes Allow HDD SAS/SATA Mix in VD : Yes Allow SSD SAS/SATA Mix in VD : No Allow HDD/SSD Mix in VD : No Allow SATA in Cluster : No Max Chained Enclosures : 16 Disable Ctrl-R : Yes Enable Web BIOS : Yes Direct PD Mapping : No BIOS Enumerate VDs : Yes Restore Hot Spare on Insertion : No Expose Enclosure Devices : Yes Maintain PD Fail History : Yes Disable Puncturing : No Zero Based Enclosure Enumeration : No PreBoot CLI Enabled : Yes LED Show Drive Activity : Yes Cluster Disable : Yes SAS Disable : No Auto Detect BackPlane Enable : SGPIO/i2c SEP Use FDE Only : No Enable Led Header : No Delay during POST : 0 EnableCrashDump : No Disable Online Controller Reset : No EnableLDBBM : No Un-Certified Hard Disk Drives : Allow Treat Single span R1E as R10 : No Max LD per array : 16 Power Saving option : Don't Auto spin down Configured Drives Max power savings option is not allowed for LDs. Only T10 power conditions are to be used. Default spin down time in minutes: 30 Enable JBOD : No TTY Log In Flash : No Auto Enhanced Import : No BreakMirror RAID Support : No Disable Join Mirror : No Enable Shield State : Yes Time taken to detect CME : 60s Exit Code: 0x00 Enclosure information: # /opt/MegaRAID/MegaCli/MegaCli64 -encinfo -a1 Number of enclosures on adapter 1 -- 3 Enclosure 0: Device ID : 36 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port B Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 65 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11820 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 48 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 1: Device ID : 65 Number of Slots : 28 Number of Power Supplies : 2 Number of Fans : 3 Number of Temperature Sensors : 1 Number of Alarms : 1 Number of SIM Modules : 0 Number of Physical Drives : 28 Status : Normal Position : 1 Connector Name : Port A Enclosure type : SES VendorId is LSI CORP and Product Id is SAS2X36 VendorID and Product ID didnt match FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : 36 Inquiry data : Vendor Identification : LSI CORP Product Identification : SAS2X36 Product Revision Level : 0718 Vendor Specific : x36-55.7.24.1 Number of Voltage Sensors :2 Voltage Sensor :0 Voltage Sensor Status :OK Voltage Value :5020 milli volts Voltage Sensor :1 Voltage Sensor Status :OK Voltage Value :11760 milli volts Number of Power Supplies : 2 Power Supply : 0 Power Supply Status : OK Power Supply : 1 Power Supply Status : OK Number of Fans : 3 Fan : 0 Fan Speed :Low Speed Fan Status : OK Fan : 1 Fan Speed :Low Speed Fan Status : OK Fan : 2 Fan Speed :Low Speed Fan Status : OK Number of Temperature Sensors : 1 Temp Sensor : 0 Temperature : 47 Temperature Sensor Status : OK Number of Chassis : 1 Chassis : 0 Chassis Status : OK Enclosure 2: Device ID : 252 Number of Slots : 8 Number of Power Supplies : 0 Number of Fans : 0 Number of Temperature Sensors : 0 Number of Alarms : 0 Number of SIM Modules : 1 Number of Physical Drives : 0 Status : Normal Position : 1 Connector Name : Unavailable Enclosure type : SGPIO Failed in first Inquiry commnad FRU Part Number : N/A Enclosure Serial Number : N/A ESM Serial Number : N/A Enclosure Zoning Mode : N/A Partner Device Id : Unavailable Inquiry data : Vendor Identification : LSI Product Identification : SGPIO Product Revision Level : N/A Vendor Specific : Exit Code: 0x00 Now, notice that each slot 11 device shows an enclosure ID of 36, I think this is where the discrepancy happens. One should be 36. But the other should be on enclosure 65. Drives in slot 11: Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 5, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 48 WWN: Sequence Number: 11 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : YES Device Firmware Level: A5C0 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8a53 Connected Port Number: 1(path0) Inquiry Data: MJ1311YNG6YYXAHitachi HDS5C3030ALA630 MEAOA5C0 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Enclosure Device ID: 36 Slot Number: 11 Drive's postion: DiskGroup: 19, Span: 0, Arm: 1 Enclosure position: 0 Device Id: 19 WWN: Sequence Number: 4 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SATA Raw Size: 2.728 TB [0x15d50a3b0 Sectors] Non Coerced Size: 2.728 TB [0x15d40a3b0 Sectors] Coerced Size: 2.728 TB [0x15d400000 Sectors] Firmware state: Online, Spun Up Is Commissioned Spare : NO Device Firmware Level: A580 Shield Counter: 0 Successful diagnostics completion on : N/A SAS Address(0): 0x5003048000ee8e53 Connected Port Number: 0(path0) Inquiry Data: MJ1313YNG1VA5CHitachi HDS5C3030ALA630 MEAOA580 FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive Temperature :30C (86.00 F) PI Eligibility: No Drive is formatted for PI information: No PI: No PI Drive's write cache : Disabled Drive's NCQ setting : Enabled Port-0 : Port status: Active Port's Linkspeed: 6.0Gb/s Drive has flagged a S.M.A.R.T alert : No Update 06/28/12: I finally have some new information about (what we think) the root cause of this problem so I thought I would share. After getting in contact with a very knowledgeable Supermicro tech, they provided us with a tool called Xflash (doesn't appear to be readily available on their FTP). When we gathered some information using this utility, my colleague found something very strange: root@mogile2 test]# ./xflash.dat -i get avail Initializing Interface. Expander: SAS2X36 (SAS2x36) 1) SAS2X36 (SAS2x36) (50030480:00EE917F) (0.0.0.0) 2) SAS2X36 (SAS2x36) (50030480:00E9D67F) (0.0.0.0) 3) SAS2X36 (SAS2x36) (50030480:0112D97F) (0.0.0.0) This lists the connected enclosures. You see the 3 connected (we have since added a 3rd and a 4th which is not yet showing up) with their respective SAS address / WWN (50030480:00EE917F). Now we can use this address to get information on the individual enclosures: [root@mogile2 test]# ./xflash.dat -i 5003048000EE917F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00EE917F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 5003048000E9D67F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:00E9D67F Enclosure Logical Id: 50030480:0000007F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 [root@mogile2 test]# ./xflash.dat -i 500304800112D97F get exp Initializing Interface. Expander: SAS2X36 (SAS2x36) Reading the expander information.......... Expander: SAS2X36 (SAS2x36) B3 SAS Address: 50030480:0112D97F Enclosure Logical Id: 50030480:0112D97F IP Address: 0.0.0.0 Component Identifier: 0x0223 Component Revision: 0x05 Did you catch it? The first 2 enclosures logical ID is partially masked out where the 3rd one (which has a correct unique enclosure ID) is not. We pointed this out to Supermicro and were able to confirm that this address is supposed to be set during manufacturing and there was a problem with a certain batch of these enclosures where the logical ID was not set. We believe that the RAID controller is determining the ID based on the logical ID and since our first 2 enclosures have the same logical ID, they get the same enclosure ID. We also confirmed that 0000007F is the default which comes from LSI as an ID. The next pointer that helps confirm this could be a manufacturing problem with a run of JBODs is the fact that all 6 of the enclosures that have this problem begin with 00E. I believe that between 00E8 and 00EE Supermicro forgot to program the logical IDs correctly and neglected to recall or fix the problem post production. Fortunately for us, there is a tool to manage the WWN and logical ID of the devices from Supermicro: ftp://ftp.supermicro.com/utility/ExpanderXtools_Lite/. Our next step is to schedule a shutdown of these JBODs (after data migration) and reprogram the logical ID and see if it solves the problem. Update 06/28/12 #2: I just discovered this FAQ at Supermicro while Google searching for "lsi 0000007f": http://www.supermicro.com/support/faqs/faq.cfm?faq=11805. I still don't understand why, in the last several times we contacted Supermicro, they would have never directed us to this article :\

  Read the article

• Can't remove GPT data from MBR

  - by user2373121

  I am having difficulty getting the Ubuntu installer (and gparted) to recognize the partitions on my MBR type disk. Other operating systems and disk tools read the disk structure and the files on it fine. I have used fixparts to write a new MBR but the issue persists. I assume the issue stems from the Protective MBR data still present on the disk but I am at a loss as to how to remove it while preserving my NTFS data partition. Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. c:\Users\mike\Desktop\fixpartsfixparts 3: FixParts 0.8.8 Loading MBR data from 3: Warning: 0xEE partition doesn't start on sector 1. This can cause problems in some OSes. MBR command (? for help): Running gdisk shows Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. c:\Users\mike\Desktop\fixparts>gdisk 3: GPT fdisk (gdisk) version 0.8.7 Partition table scan: MBR: MBR only BSD: not present APM: not present GPT: not present *************************************************************** Found invalid GPT and valid MBR; converting MBR to GPT format in memory. THIS OPERATION IS POTENTIALLY DESTRUCTIVE! Exit by typing 'q' if you don't want to convert your MBR partitions to GPT format! *************************************************************** ************************************************************************ Most versions of Windows cannot boot from a GPT disk, and most varieties prior to Vista cannot read GPT disks. Therefore, you should exit now unless you understand the implications of converting MBR to GPT or creating a new GPT disk layout! ************************************************************************ Are you SURE you want to continue? (Y/N): y Command (? for help): p Disk 3:: 2930277168 sectors, 1.4 TiB Logical sector size: 512 bytes Disk identifier (GUID): BFE92CE8-F93D-4141-82B8-816AD06FB36E Partition table holds up to 128 entries First usable sector is 34, last usable sector is 2930277134 Partitions will be aligned on 2048-sector boundaries Total free space is 163846893 sectors (78.1 GiB) Number Start (sector) End (sector) Size Code Name 1 163842048 2930272255 1.3 TiB 0700 Microsoft basic data Command (? for help): r Recovery/transformation command (? for help): o Disk size is 2930277168 sectors (1.4 TiB) MBR disk identifier: 0x00000000 MBR partitions: Number Boot Start Sector End Sector Status Code 1 1 2930277167 primary 0xEE Recovery/transformation command (? for help): q

  Read the article

• Can't add Fedora 14 to grub.

  - by Dananjaya

  Today I installed Fedora 14 in a different partition in the same hard drive as Ubuntu. At the Fedora 14 installation, I chose not to install Boot-loader in the MBR, and instead chose to install it in the Fedora partition itself, which is according to my HD layout /sda3. After the Fedora 14 installation I booted in to Ubuntu and ran sudo update-grub but 'grub.cfg' fails to add Fedora 14 in to the OS list. Here is the output of boot-info script. Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== = Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos1)/boot/grub on this drive. sda1: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 11.04 Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sda2: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sda3: __________________________________________________________________________ File system: ext4 Boot sector type: Grub Legacy Boot sector info: Grub Legacy (v0.97) is installed in the boot sector of sda3 and looks at sector 49897340 on boot drive #1 for the stage2 file. A stage2 file is at this location on /dev/sda. Stage2 looks on partition #3 for /grub/grub.conf. Operating System: Boot files: /grub/menu.lst /grub/grub.conf sda4: __________________________________________________________________________ File system: LVM2_member Boot sector type: - Boot sector info: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78165360 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 2,048 49,865,759 49,863,712 83 Linux /dev/sda2 74,866,686 78,163,967 3,297,282 5 Extended /dev/sda5 74,866,688 78,163,967 3,297,280 82 Linux swap / Solaris /dev/sda3 49,866,752 50,890,751 1,024,000 83 Linux /dev/sda4 50,890,752 74,864,639 23,973,888 8e Linux LVM "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 03e2a8da-171f-49e9-b24d-434e66cd1140 ext4 /dev/sda3 dea81d77-a375-4d0e-954e-1829f6b91f10 ext4 /dev/sda4 mzVoj0-GHJu-DJr4-0G2Y-SzZ0-LTfW-F01yf9 LVM2_member /dev/sda5 3e89ba8e-7754-4ee4-aca1-e2a82bffb7a7 swap ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda1 / ext4 (rw,errors=remount-ro,user_xattr,commit=0) =========================== sda1/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="2" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=1024x768 load_video insmod gfxterm fi terminal_output gfxterm insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 2.6.38-8-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux /boot/vmlinuz-2.6.38-8-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.38-8-generic } menuentry 'Ubuntu, with Linux 2.6.38-8-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 echo 'Loading Linux 2.6.38-8-generic ...' linux /boot/vmlinuz-2.6.38-8-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.38-8-generic } submenu "Previous Linux versions" { menuentry 'Ubuntu, with Linux 2.6.35-28-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux /boot/vmlinuz-2.6.35-28-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.35-28-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 echo 'Loading Linux 2.6.35-28-generic ...' linux /boot/vmlinuz-2.6.35-28-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.35-28-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro quiet splash vt.handoff=7 initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(/dev/sda,msdos1)' search --no-floppy --fs-uuid --set=root 03e2a8da-171f-49e9-b24d-434e66cd1140 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### if [ "x${timeout}" != "x-1" ]; then if keystatus; then if keystatus --shift; then set timeout=-1 else set timeout=0 fi else if sleep --interruptible 3 ; then set timeout=0 fi fi fi ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda1/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation # Commented out by Dropbox # UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=3e89ba8e-7754-4ee4-aca1-e2a82bffb7a7 none swap sw 0 0 UUID=03e2a8da-171f-49e9-b24d-434e66cd1140 / ext4 errors=remount-ro,user_xattr 0 1 -------------------------------------------------------------------------------- =================== sda1: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 0.065803528 = 0.070656000 boot/grub/core.img 1 21.263332367 = 22.831329280 boot/grub/grub.cfg 1 0.771381378 = 0.828264448 boot/initrd.img-2.6.31-wl 1 2.054199219 = 2.205679616 boot/initrd.img-2.6.32-21-generic 3 2.893260956 = 3.106615296 boot/initrd.img-2.6.35-28-generic 2 6.833232880 = 7.337127936 boot/initrd.img-2.6.38-8-generic 2 1.772453308 = 1.903157248 boot/vmlinuz-2.6.32-21-generic 2 2.068012238 = 2.220511232 boot/vmlinuz-2.6.35-28-generic 1 5.532531738 = 5.940510720 boot/vmlinuz-2.6.38-8-generic 1 6.833232880 = 7.337127936 initrd.img 2 2.893260956 = 3.106615296 initrd.img.old 2 5.532531738 = 5.940510720 vmlinuz 1 2.068012238 = 2.220511232 vmlinuz.old 1 ============================= sda3/grub/grub.conf: ============================= -------------------------------------------------------------------------------- # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,2) # kernel /vmlinuz-version ro root=/dev/mapper/VolGroup-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda3 default=0 timeout=0 splashimage=(hd0,2)/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.35.6-45.fc14.i686) root (hd0,2) kernel /vmlinuz-2.6.35.6-45.fc14.i686 ro root=/dev/mapper/VolGroup-lv_root rd_LVM_LV=VolGroup/lv_root rd_LVM_LV=VolGroup/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /initramfs-2.6.35.6-45.fc14.i686.img -------------------------------------------------------------------------------- =================== sda3: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) 23.792903900 = 25.547436032 grub/grub.conf 1 23.792903900 = 25.547436032 grub/menu.lst 1 23.793020248 = 25.547560960 grub/stage2 1 23.817364693 = 25.573700608 initramfs-2.6.35.6-45.fc14.i686.img 2 23.787566185 = 25.541704704 initrd-plymouth.img 1 23.791228294 = 25.545636864 vmlinuz-2.6.35.6-45.fc14.i686 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda2 00000000 81 71 62 ff a1 94 89 ff 4d 43 3a ff fa f2 ec ff |.qb.....MC:.....| 00000010 fb f6 f1 ff fc f8 f4 ff fc f8 f4 ff fc f8 f4 ff |................| 00000020 5d 56 50 ff a1 94 89 ff 81 70 62 ff 81 70 62 ff |]VP......pb..pb.| 00000030 81 70 62 ff 81 70 62 ff 81 70 62 ff a1 94 89 ff |.pb..pb..pb.....| 00000040 4d 43 3a ff fa f2 ec ff fb f6 f1 ff fc f8 f4 ff |MC:.............| 00000050 fc f8 f4 ff fc f8 f4 ff 5d 56 50 ff a1 94 89 ff |........]VP.....| 00000060 81 70 62 ff 81 70 62 ff 81 70 62 ff 81 70 62 ff |.pb..pb..pb..pb.| 00000070 81 70 62 ff a1 94 89 ff 4d 43 3a ff fa f2 ec ff |.pb.....MC:.....| 00000080 fb f6 f1 ff fc f8 f4 ff fc f8 f4 ff fc f8 f4 ff |................| 00000090 5d 56 50 ff a0 93 89 ff 80 6f 61 ff 80 6f 61 ff |]VP......oa..oa.| 000000a0 80 6f 61 ff 80 6f 61 ff 80 6f 61 ff a0 93 89 ff |.oa..oa..oa.....| 000000b0 4d 43 3a ff fa f2 ed ff fb f6 f2 ff fc f8 f5 ff |MC:.............| 000000c0 fc f8 f5 ff fc f8 f5 ff 5d 56 50 ff 9f 93 88 ff |........]VP.....| 000000d0 7f 6f 60 ff 7f 6f 60 ff 7f 6f 60 ff 7f 6f 60 ff |.o`..o`..o`..o`.| 000000e0 7f 6f 60 ff 9f 93 88 ff 4d 43 3a ff fa f2 ed ff |.o`.....MC:.....| 000000f0 fb f6 f2 ff fc f8 f5 ff fc f8 f5 ff fc f8 f5 ff |................| 00000100 5d 56 50 ff 9f 93 88 ff 7f 6f 60 ff 7f 6f 60 ff |]VP......o`..o`.| 00000110 7f 6f 60 ff 7f 6f 60 ff 7f 6f 60 ff 9f 93 88 ff |.o`..o`..o`.....| 00000120 4d 43 3a ff fa f2 ed ff fb f6 f2 ff fc f8 f5 ff |MC:.............| 00000130 fc f8 f5 ff fc f8 f5 ff 5d 56 50 ff 9e 92 88 ff |........]VP.....| 00000140 7e 6e 60 ff 7e 6e 60 ff 7e 6e 60 ff 7e 6e 60 ff |~n`.~n`.~n`.~n`.| 00000150 7e 6e 60 ff 9e 92 88 ff 4d 43 3a ff fa f2 ed ff |~n`.....MC:.....| 00000160 fb f6 f2 ff fc f8 f5 ff fc f8 f5 ff fc f8 f5 ff |................| 00000170 5d 56 50 ff 9e 92 88 ff 7d 6d 5f ff 7d 6d 5f ff |]VP.....}m_.}m_.| 00000180 7d 6d 5f ff 7d 6d 5f ff 7d 6d 5f ff 9e 92 88 ff |}m_.}m_.}m_.....| 00000190 4d 43 3a ff fa f2 ed ff fb f6 f2 ff fc f8 f5 ff |MC:.............| 000001a0 fc f8 f5 ff fc f8 f5 ff 5d 56 50 ff 9e 92 88 ff |........]VP.....| 000001b0 7d 6d 5f ff 7d 6d 5f ff 7d 6d 5f ff 7d 6d 00 fe |}m_.}m_.}m_.}m..| 000001c0 ff ff 82 fe ff ff 02 00 00 00 00 50 32 00 00 00 |...........P2...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== unlzma: Decoder error According to this Fedora 14 is visible in sda3. Does anybody know a way to add Fedora 14 to grub.cfg of Ubuntu so I can choose which OS to boot? Thanks in advance.

  Read the article

• grub problem after grub-repair

  - by alireza

  I had two OS,win 7 and Ubuntu, I was working with win and went out of the room and when came back I saw Grub Rescue!!! I booted live and did grub_repaire and it still says multiple active partitions.operating system not found I feel that it can not find the ubuntu hard drive at all! ! ubuntu@ubuntu:/dev$ sudo fdisk -l Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xde771741 Device Boot Start End Blocks Id System /dev/sda1 * 61 61 0 0 Empty /dev/sda2 2048 30146559 15072256 27 Hidden NTFS WinRE /dev/sda3 * 30146560 30351359 102400 7 HPFS/NTFS/exFAT /dev/sda4 30351360 334483299 152065970 7 HPFS/NTFS/exFAT ubuntu@ubuntu:/dev$ ls autofs dvdrw loop4 ppp ram5 shm tty15 tty29 tty42 tty56 ttyS10 ttyS24 uinput vcsa1 block ecryptfs loop5 psaux ram6 snapshot tty16 tty3 tty43 tty57 ttyS11 ttyS25 urandom vcsa2 bsg fb0 loop6 ptmx ram7 snd tty17 tty30 tty44 tty58 ttyS12 ttyS26 usbmon0 vcsa3 btrfs-control fd loop7 pts ram8 sr0 tty18 tty31 tty45 tty59 ttyS13 ttyS27 usbmon1 vcsa4 bus full loop-control ram0 ram9 stderr tty19 tty32 tty46 tty6 ttyS14 ttyS28 usbmon2 vcsa5 cdrom fuse mapper ram1 random stdin tty2 tty33 tty47 tty60 ttyS15 ttyS29 v4l vcsa6 cdrw fw0 mcelog ram10 rfkill stdout tty20 tty34 tty48 tty61 ttyS16 ttyS3 vcs vcsa7 char hpet mei ram11 rtc tty tty21 tty35 tty49 tty62 ttyS17 ttyS30 vcs1 vga_arbiter console input mem ram12 rtc0 tty0 tty22 tty36 tty5 tty63 ttyS18 ttyS31 vcs2 video0 core kmsg net ram13 sda tty1 tty23 tty37 tty50 tty7 ttyS19 ttyS4 vcs3 zero cpu log network_latency ram14 sda2 tty10 tty24 tty38 tty51 tty8 ttyS2 ttyS5 vcs4 cpu_dma_latency loop0 network_throughput ram15 sda3 tty11 tty25 tty39 tty52 tty9 ttyS20 ttyS6 vcs5 disk loop1 null ram2 sda4 tty12 tty26 tty4 tty53 ttyprintk ttyS21 ttyS7 vcs6 dri loop2 oldmem ram3 sg0 tty13 tty27 tty40 tty54 ttyS0 ttyS22 ttyS8 vcs7 dvd loop3 port ram4 sg1 tty14 tty28 tty41 tty55 ttyS1 ttyS23 ttyS9 vcsa ubuntu@ubuntu:/dev$ someone said { Remove the boot flag from sda1, by typing in a terminal: sudo fdisk /dev/sda1 Then press the 'a' key, and 'Enter'. Then press the '1' key, and 'Enter'. Then press the 'w' key, and 'Enter'. } but after grub-repair I got this log: http://paste.ubuntu.com/1371297/ then I try sudo fdisk /dev/sda1 and But It says unable to open /dev/sda1! which is right as sda1 is not in dev folder (look at the picture!) Can anybody help me? I need to work on my windows for the rest of the semester and don't care of my ubuntu. thank you

  Read the article

• Ubuntu Install 11.10 doesn't recognize Windows 7 installation with new HDD

  - by arlendo

  Replaced my crashed HDD with a Seagate 2TB Sata (bought from a company who pulled it from a working computer, OS unknown) and did a fresh install of Windows 7. Windows shows 100MB boot partition (bootable NTFS) and 200GB Windows partition (NTFS), the rest is unallocated. Win7 Disk Management says the partitioning type is Master Boot Record. Win7 boots and runs fine. Ubuntu 11.10 Install procedes to Allocate Drive Space screen and should say This computer currently has Windows 7 on it. What would you like to do? Instead, it says something like Install doesn't detect any existing OS on this computer. When I click on Something else, the partition table shows only the unallocated space of 1.8TB. Ubuntu Disk Utility says Partitioning: Master Boot Record, but GParted Live says Partition Table: gpt. It was my original intention to have the Windows boot partition and application partition, then install Ubuntu 11.10 using boot, root, swap, and home partitions, and maybe another partition just for data (mostly photos). Currently, I would be happy if I could just get Ubuntu installed along with Win7. I am aware of the MBR limits of 3 Primary partitions and 1 Extended partition. I suspect that my new HDD is partitioned for GPT and that is why Ubuntu can't see the Win7 installation. Am I on the right track? I was going to use Windows Disk Management to convert GPT to MBR but I only have the one drive on my AMD-64 mini-computer and it says I have to empty the drive of all partitions before I can access the Convert command. And I can't find any bootable software that would allow me to do that conversion. Here is the result of sudo fdisk -l: ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 224 heads, 19 sectors/track, 918004 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd4a68c18 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 419637247 209715200 7 HPFS/NTFS/exFAT ubuntu@ubuntu:~$ Keep in mind that I'm a definite newbie to screwing around with the inner workings of Ubuntu. I previously had Ubuntu 10.04 running with Vista and I don't remember even having to partition anything that wasn't automatic in the install. Thanks for taking a look here. My Win7 is running fine but I miss my Ubuntu.

  Read the article

• GPT Not mounting using "normal" GPT mounting techniques 12.04

  - by Roy Markham

  I've got two 2TB drivess: one MBR and the other GPT. sudo blckid /dev/sdb1 returns a blank. gdisk shows: Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Warning! Secondary partition table overlaps the last partition by 1970 blocks! You will need to delete this partition or resize it in another utility. Disk /dev/sdb: 3907027055 sectors, 1.8 TiB Logical sector size: 512 bytes Disk identifier (GUID): 38A1113D-B5E9-4B69-ABFF-ACB27AFB3DDD Partition table holds up to 128 entries First usable sector is 34, last usable sector is 3907027021 Partitions will be aligned on 8-sector boundaries Total free space is 2014 sectors (1007.0 KiB) Number Start (sector) End (sector) Size Code Name 1 34 262177 128.0 MiB 0C01 Microsoft reserved part 2 264192 3907028991 1.8 TiB 0700 Basic data partition mounting via fstab or -t gives same error when using NTFS or NTFS-3g "NTFS signature is missing" GParted says one partition is overwriting another, yet windows shows no errors at all. The drive is also mounted easily via MacOs (triple boot)

  Read the article

• How to access files on a drive from an older system, mounted in a new system?

  - by David Thomas

  I've recently built a new system, after a rather large physical injury was sustained by my previous system (a precarious balance, and gravity, were not a happy mix). Surprisingly the /home drive of that system appears to have more-or-less survived the trauma. However... I decided to use a fresh drive for / (and swap) partition(s), and another fresh drive for the new /home. Now that's working, I decided to install the old /home drive (that I had assumed until now would be entirely dead and without capacity for use) into the new system to recover the files and data (so far as is possible). At this point I've run into a snag: I have no idea how to go about this (with Windows it was relatively easy, the new drive would be the latest character of the alphabet, and go from there). With 'disk utility' (System - Administration - Disk Utitlity) I've worked out which drive it is (/dev/sda) but clicking on 'mount' produces an error: 1: helper failed with: mount: according to mtab, /dev/sdb1 is already mounted on / mount failed ...if it is mounted on / I can't see it. I'm also moderately confused by the disk (device /dev/sda) being referred to as /dev/sdb1. Any and all insights would be incredibly welcome (I've already voted for: Idea #9063: New internal hard drives default automount at Brainstorm). Edited in response to Roland's request for a screenshot of disk utility: Details (so far as I know them): 40GB disk is / and swap, 1.0 TB Samsung is /home 1.0 TB Hitachi is from the old system (and was the old /home drive). Output from sudo fdisk -l pasted below: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000bef00 Device Boot Start End Blocks Id System /dev/sda1 1 121601 976760001 83 Linux Disk /dev/sdb: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00037652 Device Boot Start End Blocks Id System /dev/sdb1 * 1 4742 38084608 83 Linux /dev/sdb2 4742 4866 993281 5 Extended /dev/sdb5 4742 4866 993280 82 Linux swap / Solaris Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e8d46 Device Boot Start End Blocks Id System /dev/sdc1 1 121602 976760832 83 Linux

  Read the article

• Poll: UC Uptake on the Rise

  CDW's tracking poll finds unified communications adoption up in enterprise, government, education, and healthcare sectors.

  Read the article

• 'Unable to mount Filesystem' Error

  - by Charles

  Trying to extract data from a 'bricked' Western Digital MyBook Live 2tb drive. I came across a forum that advised to use Ubuntu (booted from a CD) on my Macbook. Managed to download and create a boot CD for Ubuntu (like this little operating system btw). Booted the machine with the CD and plugged the drive (which I had extracted from it's casing and placed into a external USB SATA case & plugged to the laptop). The drive is seen by Ubuntu but each time I click on the drive, it gives me the following error: Unable to mount 2.0 TB Filesystem Error mounting: mount: wrong fs type, bad option, bad superblock on /dev/sdb4, missing codepage or helper program, or other error In some cases useful info is found in syslog -try dmesg | tail or so I am new to this and spent quite some time searching this site to see if I could find a solution to this problem without troubling anyone. I came up with a few that came close but some of the questioners mentioned that they had lost data...which scared me from going further. I need to basically extract 1 particular folder from the drive. If I can get to mount this volume 'sdb4', there is a folder called 'My_Work' which I need to back up. The rest I have/had a copy of. When I typed in dmesg | tail...I got several lines..but I think ones that are relevant are: [ 406.864677] EXT4-fs (sdb4): bad block size 65536 [ 429.098776] hfs: write access to a journaled filesystem is not supported, use the force option at your own risk, mounting read-only [ 439.786365] hfs: write access to a journaled filesystem is not supported, use the force option at your own risk, mounting read-only [ 445.982692] EXT4-fs (sdb4): bad block size 65536 [ 1565.841690] EXT4-fs (sdb4): bad block size 65536 I read somewhere to try/check 'sudo fdisk -l /dev/sdb4'. It gave me the following result: Disk /dev/sdb44: 1995.8 GB, 1995774623744 bytes 255 heads, 63 sectors/track, 242639 cylinders, total 3897997312 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdb4 doesn't contain a valid partition table This is where I reached and got frustrated and decided to try & get help on this without digging myself deeper into a hole! I understand that the answer may already be out there. If so, could someone please point me in the right direction. And if not, could someone please resolve (if possible) my situation!

  Read the article

• Reading Partition Start and End in TestDisk

  - by neanderslob

  I'm using TestDisk in an attempt to recover a partition gone terribly awry. Identifying the partition in question should simply be a matter of simply recognizing the location in the disk that it occupies. Since I know the location of the partition in question from GParted, I need to translate that over to the format that TestDisk uses, which I can't quite figure out. GParted gives the First and Last sectors as follows: First Sector: 1708032 Last Sector: 54637719 Total sector: 52929688 Test Disk gives the partitions in the following way: Start: 1691 110 20 End: 4986 39 5 Size in Sectors: 52929688 My question is: how do I translate the location specified in GParted to that in TestDisk? See the following image for any contextual clarification you might need:

  Read the article

• Misused mke2fs and cannot boot into system

  - by surlogics

  I installed Ubuntu with WUBI in Windows 7 64bit, and I had installed Mandriva 2011 with a disk. I tried to learn Linux with Ubuntu and misused mke2fs; after I reboot my computer, Windows 7 and Ubuntu has crashed. As I have Mandriva, I boot into Mandriva and found # df -h /dev/sda7 12G 9.8G 1.5G 88% / /dev/sda2 15G 165M 14G 2% /media/logical /dev/sda6 119G 88G 32G 74% /media/2C9E85319E84F51C /dev/sda5 118G 59G 60G 50% /media/D25A6DDE5A6DBFB9 /dev/sda9 100G 188M 100G 1% /media/ae69134a-a65e-488f-ae7f-150d1b5e36a6 /dev/sda1 100M 122K 100M 1% /media/DELLUTILITY /dev/sda3 98G 81G 17G 83% /media/OS # fdisk /dev/sda Command (m for help): p Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd24f801e Device Boot Start End Blocks Id System /dev/sda1 2048 206847 102400 6 FAT16 /dev/sda2 * 206848 30926847 15360000 7 HPFS/NTFS/exFAT /dev/sda3 30926848 235726847 102400000 7 HPFS/NTFS/exFAT /dev/sda4 235728864 976771071 370521104 f W95 Ext'd (LBA) /dev/sda5 235728896 481488895 122880000 7 HPFS/NTFS/exFAT /dev/sda6 727252992 976771071 124759040 7 HPFS/NTFS/exFAT /dev/sda7 481500243 506674034 12586896 83 Linux /dev/sda8 506674098 514851119 4088511 82 Linux swap / Solaris /dev/sda9 514851183 727246484 106197651 83 Linux Partition table entries are not in disk order I think I may used the following command mke2fs -j -L "logical"/dev/sda2 but I had forgotten what kind of partition it was before I transfered it into ext3. perhaps ntfs Data was not lost, and I can view my files as I could in Windows. In Mandriva, there are following disks: 117.2 GB hard disk, files in it is the same as my Windows D:, and Ubuntu was installed in it; 119.0 GB hard disk is my G:, with my personal files in it; 12.0 GB is the same with Mandriva / (with means root), 101.3 GB hard disk with nothing but lost+found; DELLUTILITY should be Dell computer utilities pre-installed in my computer; logical is the disk which I had spoiled, I can view nothing but lost+found; and OS is the C: in my Windows. After I boot, grub lets me choose Mandriva or Windows. I chose Windows and it tells me: FILE system type unknown, partition type 0x7 Error 13: Invalid or unsupported executable format I doubt something wrong with windows MBR or something # cat /boot/grub/menu.lst timeout 5 color black/cyan yellow/cyan gfxmenu (hd0,6)/boot/gfxmenu default 0 title linux kernel (hd0,6)/boot/vmlinuz BOOT_IMAGE=linux root=UUID=199581b7-ac7e-4c5f-9888-24c4f213cad8 nokmsboot logo.nologo quiet resume=UUID=34c546e4-9c42-4526-aa64-bbdc0e9d64fd splash=silent vga=788 initrd (hd0,6)/boot/initrd.img title linux-nonfb kernel (hd0,6)/boot/vmlinuz BOOT_IMAGE=linux-nonfb root=UUID=199581b7-ac7e-4c5f-9888-24c4f213cad8 nokmsboot resume=UUID=34c546e4-9c42-4526-aa64-bbdc0e9d64fd initrd (hd0,6)/boot/initrd.img title failsafe kernel (hd0,6)/boot/vmlinuz BOOT_IMAGE=failsafe root=UUID=199581b7-ac7e-4c5f-9888-24c4f213cad8 nokmsboot failsafe initrd (hd0,6)/boot/initrd.img title windows root (hd0,1) makeactive chainloader +1 I can boot into Linux, but not Ubuntu, it boot into Mandriva. I don't have a boot disk. Help me find a way to make it work again.

  Read the article

• Grub cannot boot Windows 7 loader entry on 3tb drive

  - by twicejr

  It fails and it says 'cannot find device'. It will work again if I reinstall Windows, and use something like EasyBCD. But I'd like grub as a loader only, can someone help me out here? My system has a regular BIOS (p35-ds4 mainboard) so no UEFI support. Previously ran Windows 8 alongside ubuntu 13.04, now wanted windows 7 again with ubuntu 13.10. I am using disk /dev/sda. 3000.6 GB, 3000591900160 bytes 255 head, 63 sectors/track, 364801 cylinders, 5860531055 sectors Sector size (logical/fysical): 512 bytes / 4096 bytes Device Begin End Blocks ID System /dev/sda1 2048 419432447 209715200 83 Linux /dev/sda2 419432448 436013055 8290304 82 Linux swap /dev/sda3 436015102 1576339455 570162177 5 extended Partition 3 does not start on a fysical sector limit. /dev/sda4 * 1576339456 5860530175 2142095360 7 HPFS/NTFS/exFAT /dev/sda5 436015104 855443455 209714176 7 HPFS/NTFS/exFAT /dev/sda6 855445504 1576339455 360446976 7 HPFS/NTFS/exFAT

  Read the article

• Megacli is killing me, any help appreciated

  - by Stefan

  I run a server with 2 drives in raid0 configured through BIOS. I just added 2 more drives using hotplug (the server is dell r610 with RHEL 5.4 64bit) and I would like to configure a separate raid0 partition on these drives. I am getting the following error: /opt/MegaRAID/MegaCli/MegaCli64 -CfgLdAdd r0[32:2, 32:3] -a0 The specified physical disk does not have the appropriate attributes to complete the requested command. Exit Code: 0x26 All the parameters are correct and there is just no reason why this command could not work, see this (fujitsu is current raid, seagate is the new one I want to create): /opt/MegaRAID/MegaCli/MegaCli64 -PDList -aALL | egrep 'Adapter|Enclosure|Slot|Inquiry' Adapter #0 Enclosure Device ID: 32 Slot Number: 0 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA101174 Enclosure Device ID: 32 Slot Number: 1 Enclosure position: 0 Inquiry Data: FUJITSU MBD2147RC D807D0A4PA10115T Enclosure Device ID: 32 Slot Number: 2 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS033SE0TF5K Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Inquiry Data: SEAGATE ST9300603SS FS023SE070FK I also tried to set up the drive as hotspare, also some strange error: /opt/MegaRAID/MegaCli/MegaCli64 -PDHSP -Set -physdrv[32:3] -a0 Adapter: 0: Set Physical Drive at EnclId-32 SlotId-3 as Hot Spare Failed. FW error description: The specified device is in a state that doesn't support the requested command. Exit Code: 0x32 As you can see the disk is in Unconfigured, Good state: Enclosure Device ID: 32 Slot Number: 3 Enclosure position: 0 Device Id: 3 Sequence Number: 1 Media Error Count: 0 Other Error Count: 0 Predictive Failure Count: 0 Last Predictive Failure Event Seq Number: 0 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.875 GB [0x22dc0000 Sectors] Firmware state: Unconfigured(good), Spun Up SAS Address(0): 0x5000c50005cd20b1 SAS Address(1): 0x0 Connected Port Number: 3(path0) Inquiry Data: SEAGATE ST9300603SS FS023SE070FK FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: Foreign Foreign Secure: Drive is not secured by a foreign lock key Device Speed: Unknown Link Speed: Unknown Media Type: Hard Disk Device Drive Temperature :30C (86.00 F)

  Read the article

• mdadm superblock hiding/shadowing partition

  - by Kjell Andreassen

  Short version: Is it safe to do mdadm --zero-superblock /dev/sdd on a disk with a partition (dev/sdd1), filesystem and data? Will the partition be mountable and the data still there? Longer version: I used to have a raid6 array but decided to dismantle it. The disks from the array are now used as non-raid disks. The superblocks were cleared: sudo mdadm --zero-superblock /dev/sdd The disks were repartitioned with fdisk and filesystems created with mfks.ext4. All disks where mounted and everything worked fine. Today, a couple of weeks later, one of the disks is failing to be recognized when trying to mount it, or rather the single partition on it. sudo mount /dev/sdd1 /mnt/tmp mount: special device /dev/sdd1 does not exist fdisk claims there to be a partition on it: sudo fdisk -l /dev/sdd Disk /dev/sdd: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xb06f6341 Device Boot Start End Blocks Id System /dev/sdd1 1 243201 1953512001 83 Linux Of course mount is right, the device /dev/sdd1 is not there, I'm guessing udev did not create it because of the mdadm data still on it: sudo mdadm --examine /dev/sdd /dev/sdd: Magic : a92b4efc Version : 1.2 Feature Map : 0x0 Array UUID : b164e513:c0584be1:3cc53326:48691084 Name : pringle:0 (local to host pringle) Creation Time : Sat Jun 16 21:37:14 2012 Raid Level : raid6 Raid Devices : 6 Avail Dev Size : 3907027120 (1863.02 GiB 2000.40 GB) Array Size : 15628107776 (7452.06 GiB 8001.59 GB) Used Dev Size : 3907026944 (1863.02 GiB 2000.40 GB) Data Offset : 2048 sectors Super Offset : 8 sectors State : clean Device UUID : 3ccaeb5b:843531e4:87bf1224:382c16e2 Update Time : Sun Aug 12 22:20:39 2012 Checksum : 4c329db0 - correct Events : 1238535 Layout : left-symmetric Chunk Size : 512K Device Role : Active device 3 Array State : AA.AAA ('A' == active, '.' == missing) My mdadm --zero-superblock apparently didn't work. Can I safely try it again without losing data? If not, are there any suggestion on what do to? Not starting mdadm at all on boot might be a (somewhat unsatisfactory) solution.

  Read the article

• Resizing a LUKS encrypted volume

  - by mgorven

  I have a 500GiB ext4 filesystem on top of LUKS on top of an LVM LV. I want to resize the LV to 100GiB. I know how to resize ext4 on top of an LVM LV, but how do I deal with the LUKS volume? mgorven@moab:~% sudo lvdisplay /dev/moab/backup --- Logical volume --- LV Name /dev/moab/backup VG Name moab LV UUID nQ3z1J-Pemd-uTEB-fazN-yEux-nOxP-QQair5 LV Write Access read/write LV Status available # open 1 LV Size 500.00 GiB Current LE 128000 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 2048 Block device 252:3 mgorven@moab:~% sudo cryptsetup status backup /dev/mapper/backup is active and is in use. type: LUKS1 cipher: aes-cbc-essiv:sha256 keysize: 256 bits device: /dev/mapper/moab-backup offset: 3072 sectors size: 1048572928 sectors mode: read/write mgorven@moab:~% sudo tune2fs -l /dev/mapper/backup tune2fs 1.42 (29-Nov-2011) Filesystem volume name: backup Last mounted on: /srv/backup Filesystem UUID: 63877e0e-0549-4c73-8535-b7a81eb363ed Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean with errors Errors behavior: Continue Filesystem OS type: Linux Inode count: 32768000 Block count: 131071616 Reserved block count: 0 Free blocks: 112894078 Free inodes: 32044830 First block: 0 Block size: 4096 Fragment size: 4096 Reserved GDT blocks: 992 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8192 Inode blocks per group: 512 RAID stride: 128 RAID stripe width: 128 Flex block group size: 16 Filesystem created: Sun Mar 11 19:24:53 2012 Last mount time: Sat May 19 13:29:27 2012 Last write time: Fri Jun 1 11:07:22 2012 Mount count: 0 Maximum mount count: 100 Last checked: Fri Jun 1 11:03:50 2012 Check interval: 31104000 (12 months) Next check after: Mon May 27 11:03:50 2013 Lifetime writes: 118 GB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: 383bcbc5-fde9-4720-b98e-2d6224713ecf Journal backup: inode blocks

  Read the article

• I used disk copy to clone my drive, now my windows 7 profile won't load correctly

  - by RzK

  I used easeuse disk copy, after acronis, clonezilla, windows image restore failed me. Basically it copys all sectors, I set it to skip bad sectors(40). The source drive works, it just gave me a couple errors and stopped booting at one point. The drive is an identical copy, minus 40 bad errors. The drive is set to C and active partition, I rebuilt the boot order. I've ran sfc /scannow and ran chkdsk /r chkdsk found 20kb of bad sectors if I remember right. Now the issue I get is when I log into my profile which was saved right, I get a blank light blue wallpaper (non-license) explorer.exe is not running, and there are only 4 processes running in taskmanager, including taskmanager. I would try a repair install but CRTL-E would not open, nothing will open once I force start explorer.exe, almost like all services are down. What should I do? Fresh install is almost not a possibility I will try and fix this issue. sfc /scannow /offbootdir=c:\ /offwindir=c:\windows returns "Windows Resource Protection could not perform the requested operation"

  Read the article

• Reversing an lvreduce of LVM to original size

  - by praspa

  On a RHEL system that uses LVM 2 with 4K blocks. Have been successful in reducing the LV, but trying to get steps to reverse the operation so that the LV returns to its original size. Using these steps to reduce the LV by 1GB, # umount /foo # e2fsk -f /dev/mylvm/foo # resize2fs /dev/mylvm/foo <Current LV Block count - 1GB/4K> # lvreduce --size <Current # GB - 1GB> /dev/mylvm/foo Then to reverse the reduction # lvextend --size <Original #GB> /dev/mylvm/foo # resize2fs /dev/mylvm/foo The reversal gets close to the orignal size. A 'df -h' reports that it seems to be about ~ 0.1GB shy of the original size. Using these utilities, is there a better procedure to shrink and grow the LV so that the original state can be recovered effectively?

  Read the article

• Re-sizing disk partition linux/vm

  - by Tiffany Walker

  I VM Player running a linux guest and I was wanting to know how do I expand the disk? In the VM player I gave more disk space but I am not sure how to mount/expand/connect the new disk space to the system. My old disk space was 14GB [root@localhost ~]# df -h / Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-lv_root 14G 4.5G 8.2G 36% / Then I expanded it and now I see sda2 which is the new space? [root@localhost ~]# fdisk -l Disk /dev/sda: 128.8 GB, 128849018880 bytes 255 heads, 63 sectors/track, 15665 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000cd44d Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 2611 20458496 8e Linux LVM Disk /dev/mapper/VolGroup-lv_root: 14.5 GB, 14537457664 bytes 255 heads, 63 sectors/track, 1767 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/VolGroup-lv_swap: 6408 MB, 6408896512 bytes 255 heads, 63 sectors/track, 779 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Do I need to mount the new space first? resize2fs -p /dev/mapper/VolGroup-lv_root 108849018880 resize2fs 1.41.12 (17-May-2010) The containing partition (or device) is only 3549184 (4k) blocks. You requested a new size of 1474836480 blocks. resize2fs -p /dev/mapper/VolGroup-lv_root 128849018880 resize2fs 1.41.12 (17-May-2010) resize2fs: Invalid new size: 128849018880 [root@localhost ~]# lvextend -L+90GB /dev/mapper/VolGroup-lv_root Extending logical volume lv_root to 103.54 GiB Insufficient free space: 23040 extents needed, but only 0 available [root@localhost ~]# lvextend -L90GB /dev/mapper/VolGroup-lv_root Extending logical volume lv_root to 90.00 GiB Insufficient free space: 19574 extents needed, but only 0 available EDIT: So after trying pvcreate/vgextend nothing has so far worked. I'm guessing the new disk space added from VM Player is not showing up? pvscan PV /dev/sda2 VG VolGroup lvm2 [19.51 GiB / 0 free] Total: 1 [19.51 GiB] / in use: 1 [19.51 GiB] / in no VG: 0 [0 ]

  Read the article

• Formatting an external HDD stuck at 70%

  - by mahmood

  My external HDD which is a 250GB WD (powered by USB) seems to have problem! Whenever i try to copy some files, it stuck while copying. I decided to format it. So I used windows tool and performed the format (not quickly) however at nearly 70% it stuck. Then I decided to perform a low level format with lowlevel. Again it stuck at 70%. I endup that the HDD has bad sector. So is there any tool that mark the bad sectors and bypass them? It is not very reasonable to through 250GB because of some bad sectors! P.S: I saw a similar topic but there were no conclusion there either. The smart data is Attribute, raw value, value, threshold, status Read Error Rate, 50, 200, 51, OK Spin-Up Time, 3275, 154, 21, OK Start/Stop Count, 2729, 98, 0, OK Reallocated Sectors Count,0, 200, 140, OK Seek Error Rate, 0, 100, 51, OK Power-On Hours (POH), 1057, 99, 0, OK Spin Retry Count, 0, 100, 51, OK Recalibration Retries ,0, 100, 51 , OK Power Cycle Count, 1385, 99, 0, OK Power-off Retract Count, 425, 200, 0, OK Load /Unload Cycle Count,12974, 196, 0, OK Temperature, 43, 43, 0, OK Reallocation Event Count,0, 200, 0, OK Current Pending Sector Count,23,200, 0, Degradation Uncorrectable Sector Count, 0, 100, 0, OK UltraDMA CRC Error Count,6, 200, 0, OK Write Error Rate/Multi-Zone Error Rate,0,100,51, OK It seems that the most important thing is this line Current Pending Sector Count,23,200, 0, Degradation Any idea on that?

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >