Search Results

Search found 328 results on 14 pages for 'dst'.

Page 10/14 | < Previous Page | 6 7 8 9 10 11 12 13 14  | Next Page >

• Outlook 2007 meeting request varying times across users

  - by gtaylor85

  I've googled this quite a bit, but none of the answers seem to apply to me. User A creates a meeting and invites everyone to a meeting at 1:30pm. Everyone gets the meeting for 1:30pm except User B who gets it for 2:30pm. User B responds with a "Correction" for 1:30pm and it shows up to User A for 12:30pm. I've checked Time Zone settings both in Windows Time and Date settings and also in Outlook options for both computers involved. Also, the DST check boxes are all checked (4x). I'm not sure what else to check. Any ideas?

  Read the article

• Using VLC to Unicast High Definition Webcam over local gigabit LAN with low/zero delay

  - by Robin Day

  We're setting up a webcam "window" between two offices in the same buildilng. The two PC's are connected to the same gigabit switch. We're using VLC to stream the webcam over HTTP using the following commands. vlc dshow:// :dshow-caching="0" :dshow-size="640x480" :sout=#transcode{vcodec=h264,vb=0,scale=0}:http{mux=ffmpeg{mux=flv},dst=:8080/} :no-sout-rtp-sap :no-sout-standard-sap :ttl=1 :sout-keep vlc http://192.168.0.1:8080 :http-caching="0" Even with the caching set to zero, the delay in the image is a good 2-3 seconds. The CPU usage of each pc is also maxed. I'm guessing it's the transcoding that's causing much of the delay. Can anyone give me some changes to these command lines that will reduce the transcoding power, or send the webcam over a different protocol, or anything that will reduce the delay of the cameras? Bandwidth is not an issue at all as the pc's can be connected to a dedicated switch/vlan if required.

  Read the article

• Wireshark Not Displaying Packets From Other Network Devices, Even in Promisc Mode

  - by eb80

  System Setup: 1. MacBook running Mountain Lion. 2. Wireshark installed and capturing packets (I have "capture all in promiscuous mode" checked) 3. I filter out all packets with my source and destination IP using the following filter ("ip.dst != 192.168.1.104 && ip.src != 192.168.1.104") 4. On the same network as the MacBook, I use an Android device (connecting via WiFi) to make HTTP requests. Expected Results: 1. Wireshark running on the MacBook sees the HTTP request from the Android device. Actual Results: 1. I only see SSDP broadcasts from 192.168.1.1 Question: What do I need to do so that Wireshark, like Firesheep, can see and use the packets (particularly HTTP) from other network devices on the same network?

  Read the article

• syslog log of TCP packet

  - by com

  Occasionally, I noticed a lot of following messsages in syslog Nov {datetime} hostname kernel: [8226528.586232] AIF:PRIV TCP packet: IN=eth0 OUT= MAC={mac} SRC={sourceip} DST={destinationip} LEN=60 TOS=0x00 PREC=0x00 TTL=63 ID=20361 DF PROTO=TCP SPT=39950 DPT=37 WINDOW=14600 RES=0x00 SYN URGP=0 On the Internet, I found that DOS attack may cause such type of output, unfortunately, I don't understand what does this log mean. The only thing is clear for me is this log is related to network. The source host is the host where nagios is installed. Does it mean nagios somehow does behave well? And what does it mean at all?

  Read the article

• VLC stream with trickplay

  - by marjasin

  The idea is to start a video stream from one computer and watch it on another with the ability to start/stop the stream. I think I could do this with VLC but i haven't been able to figure out how. I've tried the following: (From the official forum) Stream with RTSP and RTP: on the server, run: % vlc -vvv input_stream --sout '#rtp{dst=192.168.0.12,port=1234,sdp=rtsp://server.example.org:8080/test.sdp}' on the client(s), run: % vlc rtsp://server.example.org:8080/test.sdp But this doesn't give me the ability to start/stop the stream from the client. According to the VLC release note something called "Trick play" was added in version 1.0. This seems to be what I'm looking for but i can't find any documentation that descibes how to use it.

  Read the article

• Iptable Rule to redirect all traffic requesting a specific domain

  - by user548971

  I'm on a simple linux proxy. I'd like to add iptable rules to drop all requests for a specific domain. I figured I run a dig command to get the ip addresses for the domain and then add an iptable rule for each one. It seems, however, that it doesn't work to bind to more than one ip address. So, it seems I need to add ip ranges like this... iptables -I FORWARD -p tcp -m iprange --dst-range 66.220.144.0-66.220.159.255 --dport 443 -j DROP That seems to work. However, it has proven pretty problematic to parse the output of dig and correctly create the appropriate iptable rules. Is there a better way? Thanks! EV

  Read the article

• PHP5.3 FastCGI doesn't use global config's values

  - by mega.venik

  There's a Centos6.3 system. Apache 2.2.15 + mod_fcgid + PHP 5.3.3 There's a problem with date.timezone value. It's mentioned in the global /etc/php.ini like this: date.timezone = "Europe/Moscow" And doesn't mentioned in user's local php.ini. As a result, I'm getting lot's of warnings like: Warning: date() [function.date]: It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Europe/Helsinki' for 'EEST/3.0/DST' instead in ... Including the date.timezone parameter into the user's php.ini solves the problem, but I don't think, that it's the best solution. Maybe someone have faced this problem and can give an advice? Thanks! P.S. Creating /etc/php.d/timezone.ini with the timezone info aslo does nothing:(

  Read the article

• Can mediatomb VLC profile transcode audio as MP3 rather than mpga ?

  - by djangofan

  In the /etc/mediatomb/config.xml, can mediatomb VLC profile transcode audo as MP3 rather than mpga ? My Sony GoogleTV wont render streamed .avi files files with a mpga audio in them. The original files are Divx encoded with 128kbs MP3 audio but mediatomb is transcoding them. How can I change this? Any ideas? Can I turn off the audio and video transcoding somehow? I need some ideas to try. <profile name="vlcprof" enabled="yes" type="external"> <mimetype>video/mpeg</mimetype> <agent command="vlc" arguments="-I dummy %in --sout #transcode{venc=ffmpeg,vcodec=mp2v,vb=4096,fps=25,aenc=ffmpeg,acodec=mpga,ab=192,samplerate=44100,channels=2}:standard{access=file,mux=ps,dst=%out} vlc:quit"/> <buffer size="10485760" chunk-size="131072" fill-size="2621440"/> <accept-url>yes</accept-url> <first-resource>yes</first-resource> </profile> I know that that MP3 encoding support is external to FFmpeg and must be configured appropriately, but I have no idea how to handle that. I would guess I can work around that by somehow telling ffmpeg to not transcode the audio stream? Also, should I create a separate vlcprof entry for video/avi ? Can you create more than one profile for VLC in the config.xml for mediatomb?

  Read the article

• using PixelBender to double the size of a bitmap

  - by jedierikb

  I have a performance question about pixel bender. I want to enlarge many BitmapData (double their size into new BitmapData). I was doing this with as3, but wanted to use pixel bender to get better performance. On my machines, I get great comparative performance out of many pixel bender demonstrations. To my surprise (or bad coding / understanding), I am getting much worse performance out of pixel bender -- 2 seconds to do 3000 scalings vs .5 seconds! I expected to get at least the same performance as as3. What am I doing wrong? I got the straightforward pixel bender code here (and it is included below for easy reference). package { import aCore.aUtil.timingUtils; import flash.display.BitmapData; import flash.display.Shader; import flash.display.ShaderJob; import flash.display.Sprite; import flash.display.StageAlign; import flash.display.StageScaleMode; import flash.events.Event; import flash.geom.Matrix; public class flashFlash extends Sprite { [Embed ( source="pixelbender/bilinearresample.pbj", mimeType="application/octet-stream" ) ] private static var BilinearScaling:Class; public function flashFlash( ):void { stage.align = StageAlign.TOP_LEFT; stage.scaleMode = StageScaleMode.NO_SCALE; addEventListener( Event.ENTER_FRAME, efCb, false, 0, true ); } private function efCb( evt:Event ):void { removeEventListener( Event.ENTER_FRAME, efCb, false ); traceTime( "init" ); var srcBmd:BitmapData = new BitmapData( 80, 120, false, 0 ); var destBmd:BitmapData = new BitmapData( 160, 240, false, 0 ); var mx:Matrix = new Matrix( ); mx.scale( 2, 2 ); for (var i:uint = 0; i < 3000; i++) { destBmd.draw( srcBmd, mx ); } traceTime( "scaled with as3" ); // create and configure a Shader object var shader:Shader = new Shader( ); shader.byteCode = new BilinearScaling( ); shader.data.scale.value = [2]; shader.data.src.input = srcBmd; for (var j:uint = 0; j < 3000; j++) { var shaderJob:ShaderJob = new ShaderJob( ); shaderJob.shader = shader; shaderJob.target = destBmd; shaderJob.start( true ); } traceTime( "scaled with pixel bender bilinearresample.pbj" ); } private static var _lastTraceTime:Number = new Date().getTime(); public static function traceTime( note:String ):Number { var nowTime:Number = new Date().getTime(); var diff:Number = (nowTime-_lastTraceTime); trace( "[t" + diff + "] " + note ); _lastTraceTime = nowTime; return diff; } } } And the pixel bender code: <languageVersion : 1.0;> kernel BilinearResample < namespace : "com.brooksandrus.pixelbender"; vendor : "Brooks Andrus"; version : 1; description : "Resizes an image using bilinear resampling. Constrains aspect ratio - divide Math.max( input.width / output.width, input.height / output.height ) and pass in to the scale parameter"; > { parameter float scale < minValue: 0.0; maxValue: 1000.0; defaultValue: 1.0; >; input image4 src; output pixel4 dst; void evaluatePixel() { // scale should be Math.max( src.width / output.width, src.height / output.height ) dst = sampleLinear( src, outCoord() * scale ); // bilinear scaling } }

  Read the article

• Bash script runs fine, but not in cron

  - by radiotech

  I have a script that's supposed to record a shoutcast stream for an hour, convert it to mp3, and then save it. The script runs correctly when I run it from the terminal, but I can't seem to get it to run in cron (where it should run every hour at the top of the hour). Here's the line in crontab: 0 * * * * /medialib/tech/bin/recordstream 2>&1 >> /medialib/tech/cron.log and here's the script: #!/bin/bash name="$(date +%s)" mp3_name=$name.mp3 wav_name=$name.wav timeout -sHUP 60m vlc -I dummy --sout "#transcode{channels=2}:std{access=file,mux=wav,dst=/medialib/stream_backup/wav/$wav_name" /medialib/tech/lib/listen.m3u lame --mp3input /medialib/stream_backup/wav/$wav_name /medialib/stream_backup/$mp3_name rm /medialib/stream_backup/wav/$wav_name Thank you! EDIT: Contents of cron.log (This text has been in the log file since it was transferred from an old server where it was working). VLC media player 2.0.8 Twoflower Command Line Interface initialized. Type `help' for help. > Shutting down. VLC media player 2.0.8 Twoflower Command Line Interface initialized. Type `help' for help. > Shutting down.

  Read the article

• Recording slow web stream

  - by Budric

  I'm trying to record an mpeg2 video stream from a website that doesn't have the greatest bandwidth. The video often buffers. I want to download the stream and watch it offline. The extract stream format received is: Stream #0.0[0x44]: Audio: mp2, 48000 Hz, stereo, s16, 192 kb/s Stream #0.1[0x45]: Video: mpeg2video (Main), yuv420p, 704x576 [PAR 16:11 DAR 16:9], 15000 kb/s, 27.19 fps, 25 tbr, 90k tbn, 50 tbc I use the following tool to transocde the stream: ffmpeg -i "http://url" -y -vcodec libx264 -b 3000k -acodec copy /tmp/stream.mp4 Unfortunately after a few seconds ffmpeg stops recording with an error [mpegts @ 0x1f0b9c0] PES packet size mismatch [mp2 @ 0x1f14640] incomplete frame Error while decoding stream #0.0 [mpeg2video @ 0x1f16860] ac-tex damaged at 0 26 [mpeg2video @ 0x1f16860] Warning MVs not available I've tried encoding with vlc as well with similar issues. Although vlc doesn't stop encoding, the output video has regions where it hangs. vlc -I dummy "http://url" --network-caching="1000" --sout="#transcode{vcodec=h264,vb=3000,acodec=mp3,ab=192}:std{access=file,mux=mp4,dst=/tmp/stream.mp4}" [mpeg2video @ 0x7f2d4c001e20] ac-tex damaged at 9 33 [mpeg2video @ 0x7f2d4c001e20] Warning MVs not available [mpeg2video @ 0x7f2d4c001e20] concealing 132 DC, 132 AC, 132 MV errors [mpeg2video @ 0x7f2d4c001e20] ac-tex damaged at 16 17 [mpeg2video @ 0x7f2d4c001e20] Warning MVs not available [mpeg2video @ 0x7f2d4c001e20] concealing 836 DC, 836 AC, 836 MV errors libdvbpsi error (PSI decoder): TS discontinuity (received 4, expected 3) for PID 0 I also tried flv transcoding and it shows up with its own set of issues, like output flv file hangs in certain parts. Anyone know what's wrong or how to fix this?

  Read the article

• How to handle key in PhP array if the key contains japanese characters [migrated]

  - by Jim Thio

  I have this array: [ID] => ????????-???????????__35.79_139.72 [Email] => [InBuildingAddress] => [Price] => [Street] => [Title] => ???????? ??????????? [Website] => [Zip] => [Rating Star] => 0 [Rating Weight] => 0 [Latitude] => 35.7865334803033 [Longitude] => 139.716800710514 [Building] => [City] => Unknown_Japan [OpeningHour] => [TimeStamp] => 0000-00-00 00:00:00 [CountViews] => 0 Then I do something like this: $output[$info['ID']]=$info; //mess up here $tes=$info['ID']['Title']; Well guess what it messes up. Basically even though the content of an array in PhP can be Japanese. Is this true? What's wrong. The error I got is: Debug Warning: /sdfdsfdf/api/test2.php line 36 - Cannot find element ????????-???????????__35.79_139.72 in variable Debug Warning: /sdfdsfdf/api/test2.php line 36 - main() [function.main]: It is not safe to rely on the system's timezone settings. You are required to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Asia/Krasnoyarsk' for '7.0/no DST' instead So many question mark Why is this happening. What's really going on inside PhP? Where can I learn more of such things. Most importantly, what would be the best way to handle this situation. Should I tell PhP to internally always use UTF-8? Does PhP array inherenty cannot use non ascii id?

  Read the article

• UFW blocking random packets on 443

  - by s2jcpete

  All, I have UFW setup to allow traffic on port 443. It works as expected, though I have a large amount of UFW Block log entries. To Action From -- ------ ---- 80 ALLOW Anywhere 443 ALLOW Anywhere 22222 ALLOW Anywhere 80 ALLOW Anywhere (v6) 443 ALLOW Anywhere (v6) 22222 ALLOW Anywhere (v6) However in my syslog file I see this: [UFW BLOCK] IN=eth0 OUT= MAC=XXX SRC=<foreignip> DST=<serverip> LEN=40 TOS=0x00 PREC=0x00 TTL=116 ID=22025 DF PROTO=TCP SPT=49622 DPT=443 WINDOW=0 RES=0x00 ACK RST URGP=0 About 30 or so seconds later pound (which I'm using for SSL decryption and port redirection) throws a connection timed out messsage. I'm assuming this is because UFW is blocking the packet. I'm at a loss as to an explination. Could the packet be malformed or something, is this normal? Edit - I have since changed the /etc/defaults/ufw and set ipv6=no, so the v6 rules are no longer in the mix. The server is still showing the block / connection timed out behavior though. The new ufw status output is: Status: active Logging: on (low) Default: deny (incoming), allow (outgoing) New profiles: skip To Action From -- ------ ---- 80 ALLOW IN Anywhere 443 ALLOW IN Anywhere 22222 ALLOW IN Anywhere

  Read the article

• Windows DD-esque implementation in Qt 5

  - by user1777667

  I'm trying to get into Qt and as a project I want to try and pull a binary image from a hard drive in Windows. This is what I have: QFile dsk("//./PhysicalDrive1"); dsk.open(QIODevice::ReadOnly); QByteArray readBytes = dsk.read(512); dsk.close(); QFile img("C:/out.bin"); img.open(QIODevice::WriteOnly); img.write(readBytes); img.close(); When I run it, it creates the file, but when I view it in a hex editor, it says: ëR.NTFS ..........ø..?.ÿ.€.......€.€.ÿç......UT..............ö.......ì§á.Íá.`....ú3ÀŽÐ¼.|ûhÀ...hf.ˈ...f.>..NTFSu.´A»ªUÍ.r..ûUªu.÷Á..u.éÝ..ƒì.h..´HŠ...‹ô..Í.ŸƒÄ.žX.rá;...uÛ£..Á.....Z3Û¹. +Èfÿ.......ŽÂÿ...èK.+Èwï¸.»Í.f#Àu-f.ûTCPAu$.ù..r..h.».hp..h..fSfSfU...h¸.fa..Í.3À¿(.¹Ø.üóªé_...f`..f¡..f.....fh....fP.Sh..h..´BŠ.....‹ôÍ.fY[ZfYfY..‚..fÿ.......ŽÂÿ...u¼..faàø.è.. û.è..ôëý´.‹ð¬<.t.´.»..Í.ëòÃ..A disk read error occurred...BOOTMGR is missing...BOOTMGR is compressed...Press Ctrl+Alt+Del to restart...Œ©¾Ö..Uª Is there a better way of doing this? I tried running it as admin, but still no dice. Any help would be much appreciated. Update: I changed the code a bit. Now if I specify a dd images as the input it writes the image perfectly, but when I try to use a disk as the input it only writes 0x00. QTextStream(stdout) << "Start\n"; QFile dsk("//./d:"); //QFile dsk("//./PhysicalDrive1"); //QFile dsk("//?/Device/Harddisk1/Partition0"); //QFile dsk("//./Volume{e988ffc3-3512-11e3-99d8-806e6f6e6963}"); //QFile dsk("//./Volume{04bbc7e2-a450-11e3-a9d9-902b34d5484f}"); //QFile dsk("C:/out_2.bin"); if (!dsk.open(QIODevice::ReadOnly)) qDebug() << "Failed to open:" << dsk.errorString(); qDebug() << "Size:" << dsk.size() << "\n"; // Blank out image file QFile img(dst); img.open(QIODevice::WriteOnly); img.write(0); img.close(); // Read and write operations while (!dsk.atEnd()) { QByteArray readBytes = dsk.readLine(); qDebug() << "Reading: " << readBytes.size() << "\n"; QFile img(dst); if (!img.open(QIODevice::Append)) qDebug() << "Failed to open:" << img.errorString(); img.write(readBytes); } QTextStream(stdout) << "End\n"; I guess the real problem I'm having is how to open a volume with QFile in Windows. I tried a few variants, but to no avail.

  Read the article

• ActiveMQ - "Cannot send, channel has already failed" every 2 seconds?

  - by quanta

  ActiveMQ 5.7.0 In the activemq.log, I'm seeing this exception every 2 seconds: 2013-11-05 13:00:52,374 | DEBUG | Transport Connection to: tcp://127.0.0.1:37501 failed: org.apache.activemq.transport.InactivityIOException: Cannot send, channel has already failed: tcp://127.0.0.1:37501 | org.apache.activemq.broker.TransportConnection.Transport | Async Exception Handler org.apache.activemq.transport.InactivityIOException: Cannot send, channel has already failed: tcp://127.0.0.1:37501 at org.apache.activemq.transport.AbstractInactivityMonitor.doOnewaySend(AbstractInactivityMonitor.java:282) at org.apache.activemq.transport.AbstractInactivityMonitor.oneway(AbstractInactivityMonitor.java:271) at org.apache.activemq.transport.TransportFilter.oneway(TransportFilter.java:85) at org.apache.activemq.transport.WireFormatNegotiator.oneway(WireFormatNegotiator.java:104) at org.apache.activemq.transport.MutexTransport.oneway(MutexTransport.java:68) at org.apache.activemq.broker.TransportConnection.dispatch(TransportConnection.java:1312) at org.apache.activemq.broker.TransportConnection.processDispatch(TransportConnection.java:838) at org.apache.activemq.broker.TransportConnection.iterate(TransportConnection.java:873) at org.apache.activemq.thread.PooledTaskRunner.runTask(PooledTaskRunner.java:129) at org.apache.activemq.thread.PooledTaskRunner$1.run(PooledTaskRunner.java:47) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) at java.lang.Thread.run(Thread.java:662) Due to this keyword InactivityIOException, the first thing comes to my mind is InactivityMonitor, but the strange thing is MaxInactivityDuration=30000: 2013-11-05 13:11:02,672 | DEBUG | Sending: WireFormatInfo { version=9, properties={MaxFrameSize=9223372036854775807, CacheSize=1024, CacheEnabled=true, SizePrefixDisabled=false, MaxInactivityDurationInitalDelay=10000, TcpNoDelayEnabled=true, MaxInactivityDuration=30000, TightEncodingEnabled=true, StackTraceEnabled=true}, magic=[A,c,t,i,v,e,M,Q]} | org.apache.activemq.transport.WireFormatNegotiator | ActiveMQ BrokerService[localhost] Task-2 Moreover, I also didn't see something like this: No message received since last read check for ... or: Channel was inactive for too (30000) long Do a netstat, I see these connections in TIME_WAIT state: tcp 0 0 127.0.0.1:38545 127.0.0.1:61616 TIME_WAIT - tcp 0 0 127.0.0.1:38544 127.0.0.1:61616 TIME_WAIT - tcp 0 0 127.0.0.1:38522 127.0.0.1:61616 TIME_WAIT - Here're the output when running tcpdump: Internet Protocol Version 4, Src: 127.0.0.1 (127.0.0.1), Dst: 127.0.0.1 (127.0.0.1) Version: 4 Header length: 20 bytes Differentiated Services Field: 0x00 (DSCP 0x00: Default; ECN: 0x00: Not-ECT (Not ECN-Capable Transport)) 0000 00.. = Differentiated Services Codepoint: Default (0x00) .... ..00 = Explicit Congestion Notification: Not-ECT (Not ECN-Capable Transport) (0x00) Total Length: 296 Identification: 0x7b6a (31594) Flags: 0x02 (Don't Fragment) 0... .... = Reserved bit: Not set .1.. .... = Don't fragment: Set ..0. .... = More fragments: Not set Fragment offset: 0 Time to live: 64 Protocol: TCP (6) Header checksum: 0xc063 [correct] [Good: True] [Bad: False] Source: 127.0.0.1 (127.0.0.1) Destination: 127.0.0.1 (127.0.0.1) Transmission Control Protocol, Src Port: 61616 (61616), Dst Port: 54669 (54669), Seq: 1, Ack: 2, Len: 244 Source port: 61616 (61616) Destination port: 54669 (54669) [Stream index: 11] Sequence number: 1 (relative sequence number) [Next sequence number: 245 (relative sequence number)] Acknowledgement number: 2 (relative ack number) Header length: 32 bytes Flags: 0x018 (PSH, ACK) 000. .... .... = Reserved: Not set ...0 .... .... = Nonce: Not set .... 0... .... = Congestion Window Reduced (CWR): Not set .... .0.. .... = ECN-Echo: Not set .... ..0. .... = Urgent: Not set .... ...1 .... = Acknowledgement: Set .... .... 1... = Push: Set .... .... .0.. = Reset: Not set .... .... ..0. = Syn: Not set .... .... ...0 = Fin: Not set Window size value: 256 [Calculated window size: 32768] [Window size scaling factor: 128] Checksum: 0xff1c [validation disabled] [Good Checksum: False] [Bad Checksum: False] Options: (12 bytes) No-Operation (NOP) No-Operation (NOP) Timestamps: TSval 2304161892, TSecr 2304161891 Kind: Timestamp (8) Length: 10 Timestamp value: 2304161892 Timestamp echo reply: 2304161891 [SEQ/ACK analysis] [Bytes in flight: 244] Constrained Application Protocol, TID: 240, Length: 244 00.. .... = Version: 0 ..00 .... = Type: Confirmable (0) .... 0000 = Option Count: 0 Code: Unknown (0) Transaction ID: 240 Payload Content-Type: text/plain (default), Length: 240, offset: 4 Line-based text data: text/plain [truncated] \001ActiveMQ\000\000\000\t\001\000\000\000<DE>\000\000\000\t\000\fMaxFrameSize\006\177<FF><FF><FF><FF> <FF><FF><FF>\000\tCacheSize\005\000\000\004\000\000\fCacheEnabled\001\001\000\022SizePrefixDisabled\001\000\000 MaxInactivityDurationInitalDelay\006\ It is very likely a tcp port check. This is what I see when trying telnet from another host: 2013-11-05 16:12:41,071 | DEBUG | Transport Connection to: tcp://10.8.20.9:46775 failed: java.io.EOFException | org.apache.activemq.broker.TransportConnection.Transport | ActiveMQ Transport: tcp:///10.8.20.9:46775@61616 java.io.EOFException at java.io.DataInputStream.readInt(DataInputStream.java:375) at org.apache.activemq.openwire.OpenWireFormat.unmarshal(OpenWireFormat.java:275) at org.apache.activemq.transport.tcp.TcpTransport.readCommand(TcpTransport.java:229) at org.apache.activemq.transport.tcp.TcpTransport.doRun(TcpTransport.java:221) at org.apache.activemq.transport.tcp.TcpTransport.run(TcpTransport.java:204) at java.lang.Thread.run(Thread.java:662) 2013-11-05 16:12:41,071 | DEBUG | Transport Connection to: tcp://10.8.20.9:46775 failed: org.apache.activemq.transport.InactivityIOException: Cannot send, channel has already failed: tcp://10.8.20.9:46775 | org.apache.activemq.broker.TransportConnection.Transport | Async Exception Handler org.apache.activemq.transport.InactivityIOException: Cannot send, channel has already failed: tcp://10.8.20.9:46775 at org.apache.activemq.transport.AbstractInactivityMonitor.doOnewaySend(AbstractInactivityMonitor.java:282) at org.apache.activemq.transport.AbstractInactivityMonitor.oneway(AbstractInactivityMonitor.java:271) at org.apache.activemq.transport.TransportFilter.oneway(TransportFilter.java:85) at org.apache.activemq.transport.WireFormatNegotiator.oneway(WireFormatNegotiator.java:104) at org.apache.activemq.transport.MutexTransport.oneway(MutexTransport.java:68) at org.apache.activemq.broker.TransportConnection.dispatch(TransportConnection.java:1312) at org.apache.activemq.broker.TransportConnection.processDispatch(TransportConnection.java:838) at org.apache.activemq.broker.TransportConnection.iterate(TransportConnection.java:873) at org.apache.activemq.thread.PooledTaskRunner.runTask(PooledTaskRunner.java:129) at org.apache.activemq.thread.PooledTaskRunner$1.run(PooledTaskRunner.java:47) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) at java.lang.Thread.run(Thread.java:662) 2013-11-05 16:12:41,071 | DEBUG | Unregistering MBean org.apache.activemq:BrokerName=localhost,Type=Connection,ConnectorName=ope nwire,ViewType=address,Name=tcp_//10.8.20.9_46775 | org.apache.activemq.broker.jmx.ManagementContext | ActiveMQ Transport: tcp:/ //10.8.20.9:46775@61616 2013-11-05 16:12:41,073 | DEBUG | Stopping connection: tcp://10.8.20.9:46775 | org.apache.activemq.broker.TransportConnection | ActiveMQ BrokerService[localhost] Task-5 2013-11-05 16:12:41,073 | DEBUG | Stopping transport tcp:///10.8.20.9:46775@61616 | org.apache.activemq.transport.tcp.TcpTranspo rt | ActiveMQ BrokerService[localhost] Task-5 2013-11-05 16:12:41,073 | DEBUG | Initialized TaskRunnerFactory[ActiveMQ Task] using ExecutorService: java.util.concurrent.Threa dPoolExecutor@23cc2a28 | org.apache.activemq.thread.TaskRunnerFactory | ActiveMQ BrokerService[localhost] Task-5 2013-11-05 16:12:41,074 | DEBUG | Closed socket Socket[addr=/10.8.20.9,port=46775,localport=61616] | org.apache.activemq.transpo rt.tcp.TcpTransport | ActiveMQ Task-1 2013-11-05 16:12:41,074 | DEBUG | Forcing shutdown of ExecutorService: java.util.concurrent.ThreadPoolExecutor@23cc2a28 | org.apache.activemq.util.ThreadPoolUtils | ActiveMQ BrokerService[localhost] Task-5 2013-11-05 16:12:41,074 | DEBUG | Stopped transport: tcp://10.8.20.9:46775 | org.apache.activemq.broker.TransportConnection | ActiveMQ BrokerService[localhost] Task-5 2013-11-05 16:12:41,074 | DEBUG | Connection Stopped: tcp://10.8.20.9:46775 | org.apache.activemq.broker.TransportConnection | ActiveMQ BrokerService[localhost] Task-5 2013-11-05 16:12:41,902 | DEBUG | Sending: WireFormatInfo { version=9, properties={MaxFrameSize=9223372036854775807, CacheSize=1024, CacheEnabled=true, SizePrefixDisabled=false, MaxInactivityDurationInitalDelay=10000, TcpNoDelayEnabled=true, MaxInactivityDuration=30000, TightEncodingEnabled=true, StackTraceEnabled=true}, magic=[A,c,t,i,v,e,M,Q]} | org.apache.activemq.transport.WireFormatNegotiator | ActiveMQ BrokerService[localhost] Task-5 So the question is: how can I find out the process that is trying to connect to my ActiveMQ (from localhost) every 2 seconds?

  Read the article

• SVNKit's SVNCpoyClient method not working properly

  - by Gabriel Parenza

  Hi Everyone, I am having trouble copying file using SVNKit. After copying the files from source to destination files end up one folder above the intended folder. For ex: When copying files from "https://example.com/svn/repos/trunk/project/src/ex.txt" to "https://example.com/svn/repos/branches/PackageN/project/src", files end up in "project" folder inside PackageN while my intention is to move it to "src" folder inside "project. Code I am using: svnCopySource svnCopySource[] = new SVNCopySource[]{}; SVNCommitInfo svnCommitInfo = SVNClientManager.newInstance(null,"", "").getCopyClient().doCopy(svnCopySource, dstURL, false, false, false,commitMessage, null); // SVNCopySource[] sources // SVNURL dst // boolean isMove // boolean makeParents // boolean failWhenDstExists, // String commitMessage, // SVNProperties revisionProperties

  Read the article

• SQL Reporting Services Daylight saving time query (pt 2)

  - by ross-starkey

  I posted a question a couple of days ago (SQL Reporting Services Daylight saving time query) which was I received an answer for (thanks very much) but did not elaborate on the whole problem I am experiencing. Not only did I require the returned date time format to account for day light saving but I also need the search parameter @StartDate to allow for DST. Currently if I key in a scheduled start time of 31/03/2010 11:00 and because the SQL DB has already taken the hours difference into consideration I get no results back. If I key in 31/03/2010 10:00 then the correct details are returned. Is there away using T-SQL or the like to get the search parameter to pass the adjusted time to the DB?

  Read the article

• Optimize grep, awk and sed shell stuff

  - by kockiren

  I try to sum the traffic of diffrent ports in the logfiles from "IPCop" so i write and command for my shell, but i think its possible to optimize the command. First a Line from my Logfile: 01/00:03:16 kernel INPUT IN=eth1 OUT= MAC=xxx SRC=xxx DST=xxx LEN=40 TOS=0x00 PREC=0x00 TTL=98 ID=256 PROTO=TCP SPT=47438 DPT=1433 WINDOW=16384 RES=0x00 SYN URGP=0 Now i grep with following Command the sum of all lengths who contains port 1433 grep 1433 log.dat|awk '{for(i=1;i<=10;i++)if($i ~ /LEN/)print $i};'|sed 's/LEN=//g;'|awk '{sum+=$1}END{print sum}' The for loop i need because the LEN-col is not on same position at all time. Any suggestion for optimizing this command? Regards Rene

  Read the article

• Mysql: Convert DB from local time to UTC

  - by Joernsn

  I need to convert an existing (datetime fields) db from local time ut UTC. The values are stored ad datetimes on a server with time zone CET (+1) (with summertime +2). When selecting data I use UNIX_TIMESTAMP(), which magically compensates for everything, ie, time zone shift and dst (if i've read the docs right). I'm moving the db to a new server with UTC as system time. Simply subtracting -1 H won't work, as summer time is +2. Any ideas for a clever way to do this? (using sql or some script lang)

  Read the article

• MSP430 CMP operator

  - by Ludicrous

  Let's say I have the MSP430 assembly segment below: r15: 439c Memory map: 4390: 6045 0200 9c43 6400 8844 5044 363a 0000 Code: 448a: cmp #0x363a, 0x0(r15) 4490: jnz $+0x1c 4492: Code continues . . . 44ac: Jump to location The goal is to have the Z flag high. To do this with a cmp, both src and dst must be equal. If I have 363a in the memory location of r15, why is it that the resulting cmp does not trigger the Z flag? Through experimentation, I found that putting 3a36 in the memory location of r15 did in fact trigger the Z flag, but I don't understand why. If anyone could bring this to light, I would greatly appreciate it. If more information is needed, I will gladly provide it.

  Read the article

• Can I use Duff's Device on an array in C?

  - by Ben Fossen

  I have a loop here and I want to make it run faster. I am passing in a large array. I recently heard of Duff's Device can it be applied to this for loop? any ideas? for (i = 0; i < dim; i++) { for (j = 0; j < dim; j++) { dst[RIDX(dim-1-j, i, dim)] = src[RIDX(i, j, dim)]; } }

  Read the article

• PHP: System Timezone Setting error

  - by marknt15

  Hi, I'm trying to use PHP in the terminal under MAMP but I got an error related to the system's timezone settings. How can I fix this error? $/Applications/MAMP/bin/php5/bin/php echo.php PHP Strict Standards: PHP Startup: It is not safe to rely on the system's timezone settings. Please use the date.timezone setting, the TZ environment variable or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected 'Asia/Manila' for 'PHT/8.0/no DST' instead in Unknown on line 0 Thanks

  Read the article

• how to test if a string is a valid UTF16 string?

  - by superb

  I am using mongodb and javascript to do some string processing. Now I got some error like: Sun May 23 07:42:20 Assertion failure JS_EncodeCharacters( _context , s , srclen , dst , &len) scripting/engine_spidermonkey.cpp 152 0x80f4f7e 0x80f8794 0x811525b 0x811a953 0x8119fc4 0x8111bc5 0x81b408e 0x81c4ee7 0x81b4a10 0x817a881 0x817a7d8 0x817a6e2 0x811e1bb 0x80a777b 0x80a8f8a 0xb7cb2455 0x80a37a1 mongodb-linux-i686-1.4.2/bin/mongo(_ZN5mongo12sayDbContextEPKc+0xfe) [0x80f4f7e] After doing some google, I find that JS_EncodeCharacters return false if the input is not a valid UTF16 string. (if spidermonkey is build with UTF-8 enabled) So I was wondering how to test if the input string if a proper UTF16 string? so I can skip such kind of string to avoid problem ... Thanks

  Read the article

• Get Rails to save a record to the database in a non-UTC time

  - by Shaun

  Is there a way to get Rails to save records to the database without it automagically converting the timestamp into UTC before saving? The problem is that I have a few models that pull data from a legacy database that saves everything in Mountain Time and occasionally I have to have my Rails app write to that database. The problem is that every time it does, it converts the time I give it from Mountain Time to UTC, which is 6-7 hours ahead (depending on DST)! Needless to say, this really messes with reporting on that database. If I could get around doing this, I would. Unfortunately, I can't do anything about the fact that this other database uses a different timezone, nor can I really get away from the need for this app to save to that database occasionally. If I could just get Rails to stop trying to help me, it'd be great.

  Read the article

• Get client timezone (not GMT offset amount) in JS

  - by Rex M

  I need to determine the client timezone (e.g. CET, GMT, EST) in JS. Getting the offset is straightforward, but doesn't have all the info necessary to determine the TZ, at least not easily. I have a feeling it might be possible to use a combination of offset, whether DST is in use and in effect, etc. but I'm hoping someone else has done the work already, especially considering the weird exceptions when dealing with time. This question is similar but both the question and the answer are based on the (incorrect) assumption every browser's DateString format includes the name of the timezone - which it does not. That is an implementation detail. So, with that I am currently stuck.

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14  | Next Page >