Search Results

Search found 13165 results on 527 pages for 'hyper v tools'.

Page 10/527 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

  - by GT

  The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

  Read the article

• Hyper-V server 2012 nic teaming setup and virtual switch configuration

  - by Calvin

  I have a server with 2 nics. I installed Hyper-v 2012 server (not windows server 2012, no gui) I am trying to set up load balancing. I have both nics in the same switch currently in trunk mode and no native vlan. I use the new-netlbfoteam command to create a team with both nics, I can then "set-netlbfoteamnic "Nic Team" -vlanid 4" so that its available to me with a DHCP or static address but as soon as I try to create a virtual switch it becomes unresponsive. My guess is that is due to it removing the vlan tagging I setup. if I add-netlbfoteamnic and set it for vlan 4, then set the IP I can ping it from my management computer but I just get an error "an error occurred while attempting to connect to server "xxxxxx" Check that the Virtual Machine Management service is running and that you are authorized to connect to the server."

  Read the article

• just curious if anybody every tried this- hyper-v r2

  - by tony roth

  I have a server that san boots that I want to p2v. I have many options disk2vhd, scvmm etc but I was thinking about cloning the lun (flexclone, netapp) presenting it to my hyper-v r2 server. Within the hv manager do a create new disk then have it copy the cloned lun to a vhd file. Then do the bcdedit\bootsect stuff to it. Should work right? I'm also curious if anybodys booting vhd's that are on bootable luns? I've booted native vhd's just fine was just curious about the running them off a bootable lun. I think that this has quite a few advantages like instant p2v etc.. any thoughts on this? hmm dang as I was typing this I realized that I should not use the hv manager new disk copy routine, I should just disk2vhd the mounted lun. This has advantages in that it should be a lot faster!! thanks

  Read the article

• How to monitor CPU usage and performance on a Hyper-V server with several VM's

  - by Bjørn

  Hello, I have a server that is running Windows 2008 64 bit Hyper-V, with 8 gigs of RAM and Intel Xeon X3440 @ 2.53 Ghz, which gives me 8 logical cores in the performance monitor on the host system. I have set up three Virtual Machines, all running Windows 2008 32 bit. Build server, running Team City Staging server SQL Server, running SQL Server 2005 I have some troubles with the setup in that the host monitor remains responsive at all times, even though the VM's are seemingly working at 100% cpu and are very sluggish and unresponsive. (I have asked a separate question about that.) So the question here is: What is the best way to monitor how the physical CPU's are actually utilized? The reason I am asking is that I am being told that i cannot reliably use the task manager to monitor CPU usage in a VM.

  Read the article

• CPU's on Hyper-V host system is just idling, even though VM's are at full throttle

  - by Bjørn

  Hello, I have a server that is running Windows 2008 64 bit Hyper-V, with 8 gigs of RAM and Intel Xeon X3440 @ 2.53 Ghz, which gives me 8 logical cores in the performance monitor on the host system. I have set up three Virtual Machines, all running Windows 2008 32 bit. Build server, running Team City Staging server SQL Server, running SQL Server 2005 These three machines are running very sluggishly, they are at 100% cpu even though the host system is barely using any cpu at all, typically below 10% total. Could anyone please give some tips as to the best setup for CPU allocating? Should I have set each server to have two cores, or should I increase this number above the total number of cores on the host? What is a good number to set on the Virtual Machine Reserve and Virtual Machine Limit? Is 8 gigs of physical RAM insufficient for 3 VM's? Thanks for reading. :)

  Read the article

• Ubuntu not connecting to network in Hyper-V

  - by soandos

  I am unable to connect the Ubuntu guest (both 12.10 and 12.04) to the internet via hyper-V. Here is what I have done so far (with much thanks due to @Kronos's blog post on the topic): Created a switch in the switch manager with connection set to external, selected my wifi card (Intel Centrino Ultimate-N 6300 AGN). If it matters, the Microsoft Filtering Platform is checked under extensions. Added this switch to my Ubuntu guest. I also tried a different wireless card (Aethros 9285) same issue. Connecting through my wired card works just fine (assume that I select that card, and I am wired in of course). Making it a legacy network adapter does not fix the issue. Ubuntu can see this connection, but is unable to connect to it. What follows is what I attempted to do to get Ubuntu to connect: Start and restart the network manager Restart the machine Verify that it could in fact see the adapter (resulted in device not ready a few times) How can I get this to work properly?

  Read the article

• HP DL580 G5 Hyper-V networking problem

  - by mr-perfect

  Hi I have installed the hyper-v role on a DL580 G5 cluster. The host operating system is a server 2008 x64 patched to the maximum. Everything has gone fine, but if I install a guest operating system, actually a windows server 2008 x64 I can't reach the network from it. It send many packets, but don't received any, so I can't ping the external network as well. I have installed the latest drivers to the server and unintalled the network configuration utility from the physical server, but no luck. I added a legacy adapter to the guest binded to the same phisycal adapter on the host machine but it can't help Any idea welcome...

  Read the article

• Receiving Event ID: 10107, Hyper-V -VMMS

  - by Stargaten

  We are using physical disk on two of Guest operating systems. Is this a know issue? Do we need to have DPM 2010? "One or more physical disks are attached to virtual machine 'Myserver'. Back up programs that use the Hyper-V VSS writer cannot back up volumes that are attached to virtual machines as physical disks. To avoid potential data loss, use another method to back up the data on the physical disks. If you restore the data on this virtual machine, make sure to check the data of the physical disk for integrity. (Virtual machine ID 8EF3C0CB-967D-4D67-B4D8-7B782C7AC07C)"

  Read the article

• Ubuntu Server 12.04 LTS on Hyper-V 2012

  - by user137533

  I have the following scenario: Hyper-V 2012 server core installation. On top of this i created a virtual machine on which i tried installing Ubuntu Server 12.04 which should not have any compatibility issues according to what Microsoft and Ubuntu are saying (although it is not officially supported). I start, run the installation and everything is ok, no problems detecting the network device or the hard drive (unlike debian which didn't even detect the hard drive). Once the installation is complete it asks me to reboot, it unmounts the "dvd drive" and reboots. Once it tries to start again i get the following error: Boot failure. Reboot and Select proper Boot device or Insert Boot Media in the selected Boot device. It seems to not be booting up from the virtual hard drive. The hard drive is set up in SCSI mode, nothing mounted on the IDE controller (no iso image or anything else. Does anyone have any ideas on what i can do to solve this?

  Read the article

• Tools to simulate mobile devices on a desktop to test websites

  - by Kris

  Are there any good tools that can be run on desktop machines (Windows or Linux) that can simulate a mobile device, preferably with some options as to screen size and mobile browser (user agent if not full render engine). I know it is never going to be perfect (especially without an actual touchscreen), but having a tool on our development machines to do what testing we can that way would be very useful.

  Read the article

• hyper-v multiple virtual machines with >2TB volumes from one raid

  - by wurlog

  I have a server with two Raids. Raid 0: 2x 1TB Raid 6: 8x 2TB The first raid I used for the hyper-v installation itself. The virtual machines should use the Raid 6, but how can I config it? I need at least one file server with the most of the disc space (maybe a second). But every vhd has a maximum of 2 TB and I can't use the volume directly because other virtual machines have to have access the Raid6. What do I do?

  Read the article

• Windows 2012 Server Hyper-V: Cannot see LAN

  - by Samuel

  I have one NIC on the machine loaded XP on the Hyper-V and had chosen the network as virtual switch. No LAN and no internet shows up on the client. Am I missing something? it used to work in 2008-R2. Details: One network card on machine (Qualcomm Atheros AR8131 PIC-E Gigabit Ethernet controller) The virtual machine hard disk is pointing to and existing XP-SP2 hard disk created using VPC 2007 The Virtual machine Network Adapter is setup as Virtual Switch to the real ethernet controller with Enable virtual LAN identification set to 2 (no other virtual machine is created in the system) After the virtual machine boots LAN shows empty in Control Panel Network Connections (this is XP client) and I also cannot access the internet. XP is showing activation prompt but as far as I know it should not disable the network! Virtual network switch is set to External

  Read the article

• Can a virtual mikrotik box bridge a hyper-v internal network with a hyper-v external network?

  - by mcfrosty

  I am trying to set up a Mikrotik router as a transparent firewall on my network. I got the machine working on a hardware MT box, but my boss wants the MT virtualized. I have been trying the set up where my virtual windows box talks to the Mikrotik via private or internal network on the Hyper-V host. I can get the two machines to talk, but as soon as I set up a bridge on the MT, all traffic ceases between the two. Is it possible to create a bridge for this purpose (having the MT silently in front of my firewalled server)? I could really use some help.

  Read the article

• Backing up Hyper-V VMs using "wbadmin" failing on Windows Server 2012

  - by Ederson

  I'm trying to backup a single VM using "wbdamin". I'm using this command-line: wbadmin start backup -backupTarget:d: -hyperv:VM_Machine_Name -quiet But the backup have no success. Looking at my Events, I get the following information: Source: SSP Event ID: 16387 Level: Error "Writer Microsoft Hyper-V VSS Writer experienced some error during snapshot creation. More info: ." ============================= Source: Backup Event ID: 521 Level: Error "The backup operation that started at '?2014?-?06?-?11T15:38:44.459000000Z' has failed because the Volume Shadow Copy Service operation to create a shadow copy of the volumes being backed up failed with following error code '0x8100010C'. Please review the event details for a solution, and then rerun the backup operation once the issue is resolved." ============================= Source: VSS No Event Errors. I didn't find any info about "0x8100010C" error code through the web and I'm stuck. Anyone know how to fix this?

  Read the article

• Deploy virtual PC based on snapshot using Hyper-V

  - by user27786

  I have a server with Hyper-V configured, it is easy to create a new virtual machine using the management tools, but it can take some time. I often see those hosts that say "We can have your server ready in 5 seconds". And I wonder how do they manage this? I would also like to deploy a full functional clean server in 5 seconds. So how is this done? Is it by first installing a clean server, then take a snapshot of that for later to deploy a new server based on that snapshot? I tried doing this, but I did not find any where to install a new virtual machine based on the snapshot. Anyone got any thoughts to share on this?

  Read the article

• Hyper-V R2 Performance Counters

  - by Ascendo

  Hi all I've been playing around with the WMI performance counters for Hyper-V. Of interest to me are the Virtual NIC bytes/sec input and output counters. I notice that the results are very "spikey". Over what time period is the latest counter averaged? I'm trying to calculate total traffic volume per VM, but sometimes a very high instantaneous poll result is inflating the result as I only poll the result each minute. I would prefer to read a 'bytes total' counter instead of a 'bytes/sec' counter - is there such a thing? Thanks Acendo

  Read the article

• What non-programming tools do programmers use?

  - by user828584

  I'm reading code complete with the intention of learning how to better structure my code, but I'm also learning a lot about how many aspects of programming something there are that aren't just writing the code. The book talks a lot about problem definition, determining the requirements, defining the structure, designing the code, etc. What tools are used for these non-writing steps of programming? Is there software that will help me design and plan out what I'm going to write before I do?

  Read the article

• Newbie one: Virtual Networks - Hyper-V - Remote Destktop - Only one phisical NIC

  - by josecortesp

  Hello everyone, I'll try to explain my situation and I'll apreciate any help: I have a phisical server (quad core, 4Gb ram, 1TB raid 10, etc) with Win Server 2008 R2 enterprise, running IIS, Printing, etc... Also, I want to set up 2 virtual Servers with 2008 R2 standart one with SQL Server and the other with Team Foundation. What i need is: Being able to access from inside the private phisical network, to Remote Desktops on each of the Virtual and the phisical Servers Had Access from the outside, using a router and port Forwarding, to the TFS server and the IIS server (one is virtualized, the other is phisical) This is it, but note that I only have one Phisical Nic. How do I configure this to work. When i set up the hyper-v role, on the wizard something like it showed up but I don't remmember what i choose, and right now, I cannot access none of the servers from remote desktop, not even from the phisical private network. Can anybody point me, what can i do? Thanks in advance (sorry 4 my english, i'm a spanish talker and my english isn't that good)

  Read the article

• Webmaster Tools: root and subdirectories?

  - by nick

  We have all our international sites on our .com domain like this: site.com/uk site.com/us etc... When creating the sites in Webmaster Tools I've created different sites and submitted sitemaps for each directory so that we can appropriately geotarget the site. Is it also recommended to add the root .com with its geotargeting set to international? If so should I also add all the seperate site maps (like the /us/sitemap.xml) even though they have been added to the directory level sites?

  Read the article

• Understanding CTR in Google Webmaster Tools

  - by sam

  I've got a site that's showing a 9% CTR for a phrase in Google Webmaster Tools, but the average position for my site is 14th (this includes 7 local results for this phrase). I was a little confused as to what the CTR actually meant, is it : for each person who searches for that phrase 9% of them click my site. or for each person who actually sees my site in the search results 9% of them click through (bearing in mind 14th is high on page 2 when the local listings are used).

  Read the article

• Tools for creating assets? [closed]

  - by Agent_9191

  There are similar questions about finding existing resources that are free for use (free sprites/images, music, sound), but I'm interested in creating the resources myself. What tools do you use for asset creation/modification? Please only put one tool per answer. Also try to include the following information: Product Name Link to website Type of assets is can create (2D images, 3D images, audio, etc) OS(s) supported Cost License (if free/open source) General summary

  Read the article

• Hyper-V and custom resolution

  - by Thomas Levesque

  I know this question has been asked many times (here and on TechNet), and the answer is usually "use RDP". But apparently, RDP is now the only option, and it's what I'm using. My screen is an LCD TV with a resolution of 1360x768. Unfortunately, this resolution is apparently not supported; the closest I can get in a Windows 8 VM is 1366x768, and it adds scrollbars, which make it difficult to put the mouse in the corners to get at the start screen and charm bar... Smaller resolutions don't fill the screen, so it's also difficult to put the mouse in the corner. Is there a way to set a custom resolution to fit my screen exactly ? (note: I know it's not a Windows 8 problem, since I don't have this problem on my host machine which also runs Windows 8. I assume it's related to the display adapter used by Hyper-V, but there don't seem to be any options to change it)

  Read the article

• Hyper-v error starting vm after reboot

  - by mamu

  Hi rebooted hyper-v host running server 2008 r2. After reboot one of my vm is throwing following error. 'The version does not support this version of file format' Out of my all vms this was only set to save state when shutdown. I tried deleting state and start still same error. Tried inspect disk as well edit disk both throw same error when try to open this. What could it be? any way to resolve it?

  Read the article

• Hyper-V Server hvremote.wsf Script - ns lookup for DNS Verification test fails

  - by Vazgen

  I'm trying to connect my Hyper-V Server to a Windows 8 client for remote management. I have: Joined server to WORKGROUP Enabled Remote Management Set the server name Set a static IP Set the DNS servers to my ISPs DNS Servers (same as default DNS Servers on my Windows 8 remote management client) Set the correct time zone Created net user on server (net user /add admin password) Added user to special Administrators group on server (hvremote /add:admin) Granted anonymous dcom access on client using hvremote However, the "ns lookup for DNS verification" fails on both the client and server with the same error: Server: my.isps.server.name.net Address: 111.222.333.1 *** my.isps.server.name.net can't find 192.168.1.3: Non-existent domain Thanks for the help.

  Read the article

• Webmaster Tools - Preferred Domain and Google entries

  - by xylar

  Our client has two websites with the same content: example.com somethingelse.com When a user searchs in google for "something else" the example.com site appears in the top 10 results on google. What would happen if we switched the preferred domain in webmaster tools to somethingelse.com? Our client is hoping it will replace the "example.com" result with "somethingelse.com" but I assume this is not the case.

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >