Search Results

Search found 6870 results on 275 pages for 'usb powered'.

Page 10/275 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• The Internet Key Wave MW833UP is not recognized in Ubuntu

  - by gio900

  I can't use my Onda MW833UP... :( Any advice? Here is something that someone else may understand: ~$: lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 11.10 Release: 11.10 Codename: oneiric ~$: lsusb Bus 001 Device 005: ID 1ee8:0012 ~$: dmesg [ 22.709475] cdc_acm 1-1:1.0: ttyACM0: USB ACM device [ 22.714856] usbcore: registered new interface driver cdc_acm [ 22.714866] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 23.520490] ieee80211 phy0: wl_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) [ 24.244530] usbcore: registered new interface driver usbserial [ 24.244575] USB Serial support registered for generic [ 24.244673] usbcore: registered new interface driver usbserial_generic [ 24.244681] usbserial: USB Serial Driver core [ 24.265879] USB Serial support registered for GSM modem (1-port) [ 24.285680] usbcore: registered new interface driver option [ 24.285691] option: v0.7.2:USB Driver for GSM modems [ 24.425878] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro,commit=600 [ 24.736540] EXT4-fs (sda8): re-mounted. Opts: commit=600 [ 35.705796] Easy slow down manager: checking for SABI support. [ 35.706002] Easy slow down manager: SABI is supported (f5189) [ 36.060099] usbcore: deregistering interface driver uvcvideo [ 139.508061] CE: hpet increased min_delta_ns to 20113 nsec [ 6798.378917] usb 1-1: USB disconnect, device number 5 [ 6809.108232] usb 1-1: new high speed USB device number 6 using ehci_hcd [ 6809.242692] scsi5 : usb-storage 1-1:1.0 [ 6810.241257] scsi 5:0:0:0: CD-ROM Onda Datacard CD-ROM 0001 PQ: 0 ANSI: 0 [ 6810.241841] scsi 5:0:0:1: Direct-Access Onda Storage 0001 PQ: 0 ANSI: 0 [ 6810.271410] sr0: scsi3-mmc drive: 0x/0x caddy [ 6810.272099] sr 5:0:0:0: Attached scsi CD-ROM sr0 [ 6810.272852] sr 5:0:0:0: Attached scsi generic sg1 type 5 [ 6810.279954] sd 5:0:0:1: [sdb] Attached SCSI removable disk [ 6810.281210] sd 5:0:0:1: Attached scsi generic sg2 type 0 [ 6810.380591] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.380617] sr: Sense Key : Hardware Error [current] [ 6810.380625] sr: Add. Sense: No additional sense information [ 6810.613937] sr0: CDROM (ioctl) error, command: Xpwrite, Read disk info 51 00 00 00 00 00 00 00 02 00 [ 6810.613972] sr: Sense Key : Hardware Error [current] [ 6810.613984] sr: Add. Sense: No additional sense information [ 6810.673716] usb 1-1: USB disconnect, device number 6 [ 6815.572142] usb 1-1: new high speed USB device number 7 using ehci_hcd [ 6815.706828] cdc_acm 1-1:1.0: ttyACM0: USB ACM device The last 3 lines are where I inserted the Internet key, then reconnected it. usb-device T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=1ee8 ProdID=0012 Rev=00.01 S: Manufacturer=Onda S: Product=MW833UP S: SerialNumber=9230B35D870F9CB7AE684EACC5C12BE5EC33B26E C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm Then there is /dev/ttyACM0. When the key is connected to the USB port, everything that will meant...

  Read the article

• Nec USB 3.0 controller drops connection - Ubuntu 12.04.1

  - by Tom

  I have some serious problems with Technaxx pci-e 302p card. It has uPD720200a NEC chip with 4020 firmware. BIOS recognises it. Sometimes it recognises devices and system mounts them and are functional for few minutes, other times they can't be mount and error occours. After fresh install card worked fine, but after kernel and firmware update it behaves as mentioned. Outputs: uname -a Linux asd-GA-MA770-UD3 3.2.0-30-generic #48-Ubuntu SMP Fri Aug 24 16:52:48 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lspci -vvv USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) (prog-if 30 [XHCI]) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fd8fe000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: xhci_hcd lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 07d1:3c0a D-Link System DWA-140 RangeBooster N Adapter(rev.B2) [Ralink RT3072] Bus 005 Device 004: ID 1997:1221 Bus 005 Device 003: ID 15c2:003c SoundGraph Inc. lsmod Module Size Used by nls_iso8859_1 12713 0 nls_cp437 16991 0 vfat 17585 0 fat 61512 1 vfat vesafb 13844 1 saa7134_alsa 18602 1 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep tda827x 18182 1 snd_hda_codec_hdmi 32474 1 ir_lirc_codec 12859 0 lirc_dev 19204 1 ir_lirc_codec tda8290 22616 1 arc4 12529 2 snd_hda_codec_realtek 224173 1 ir_mce_kbd_decoder 12777 0 ir_sony_decoder 12510 0 ir_jvc_decoder 12507 0 tuner 27428 1 ir_rc6_decoder 12507 0 snd_hda_intel 33773 5 rt2800usb 22684 0 rt2800lib 58925 1 rt2800usb crc_ccitt 12667 1 rt2800lib rt2x00usb 20762 1 rt2800usb rt2x00lib 51144 3 rt2800usb,rt2800lib,rt2x00usb mac80211 506816 3 rt2800lib,rt2x00usb,rt2x00lib ir_rc5_decoder 12507 0 rc_avermedia_m135a 12526 0 rc_imon_pad 12505 0 ir_nec_decoder 12507 0 cfg80211 205544 2 rt2x00lib,mac80211 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_ctxfi 111202 2 snd_hwdep 13668 1 snd_hda_codec imon 32839 0 snd_pcm 97188 5 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_ctxfi snd_seq_midi 13324 0 saa7134 181851 1 saa7134_alsa videobuf_dma_sg 19354 2 saa7134_alsa,saa7134 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi joydev 17693 0 rc_core 26412 13 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_avermedia_m135a,rc_imon_pad,ir_nec_decoder,imon,saa7134 snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event fglrx 3263886 101 videobuf_core 26390 2 saa7134,videobuf_dma_sg v4l2_common 16454 2 tuner,saa7134 videodev 98259 3 tuner,saa7134,v4l2_common sp5100_tco 13791 0 snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 28 saa7134_alsa,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_ctxfi,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device v4l2_compat_ioctl32 17128 1 videodev tveeprom 21249 1 saa7134 i2c_piix4 13301 0 soundcore 15091 1 snd edac_core 53746 0 serio_raw 13211 0 snd_page_alloc 18529 3 snd_hda_intel,snd_ctxfi,snd_pcm edac_mce_amd 23709 0 wmi 19256 0 mac_hid 13253 0 ppdev 17113 0 parport_pc 32866 1 k10temp 13166 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp usb_storage 49198 0 uas 18180 0 usbhid 47199 0 hid 99559 1 usbhid firewire_ohci 41000 0 firewire_core 63558 1 firewire_ohci crc_itu_t 12707 1 firewire_core floppy 70365 0 pata_atiixp 13204 2 r8169 62099 0 dmesg | tail after plugging to usb 3.0 port [ 834.871296] sd 9:0:0:0: rejecting I/O to offline device [ 834.871308] sd 9:0:0:0: rejecting I/O to offline device [ 834.871319] sd 9:0:0:0: rejecting I/O to offline device [ 834.871330] sd 9:0:0:0: rejecting I/O to offline device [ 834.871530] sd 9:0:0:0: [sdd] Unhandled error code [ 834.871536] sd 9:0:0:0: [sdd] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [ 834.871545] sd 9:0:0:0: [sdd] CDB: Read(10): 28 00 0e 8e 48 0a 00 00 3e 00 [ 834.871564] end_request: I/O error, dev sdd, sector 244205578 [ 834.875497] sd 8:0:0:1: Device offlined - not ready after error recovery [ 834.885339] usb 9-2: USB disconnect, device number 2 Are there any other outputs need for answering? I'll post them ASAP. I could of course reject updating the system but I think it's halfway solution. Any help appreciated. BTW USB 2.0 and 1.1 ports run well, card itself runs under win7 as charm. Tom

  Read the article

• Booting the liveCD/USB in EFI mode fails on Samsung Tablet XE700T1A

  - by F.L.

  My tablet is Samsung Series 7 Slate (XE700T1A-A02FR (French Language)). It operates an Intel Sandy Bridge architecture. The main issue about this tablet is that it ships with an installed Windows 7 in (U)EFI mode (GPT partition table, etc.), so I'd like to get an EFI dual boot with Ubuntu. But it seems I can't boot on the liveCD in EFI mode. It starts loading (up to initrd), but I then get a blank (black) screen. I've tried the nomodeset kernel option (as well as removing quiet and splash) with no luck. [2012-09-27] I have used the Ubuntu 12.04.1 Desktop ISO (I have read somewhere that it is the only one that can boot in EFI mode). I'd say this has something to do with UEFI since the LiveCD boots in bios mode but not in efi mode. Besides, I am not sure my boot info will help, since I can't boot the LiveCD in EFI mode. As a result I can't install ubuntu in EFI mode. So it would be the boot info from the liveCD boot in bios mode. This happens on a ubuntu-12.04.1-desktop-amd64 iso used on a LiveUSB. Live USB was created by dd'ing the iso onto the full disk device (i.e. /dev/sdx no number) of the Flash drive. I have also tried copying the LiveCD files on a primary GPT partition, but with no luck, I just get the grub shell, no menu, no install option. [2012-09-28] I tried today a flash drive created with Ubuntu's Startup Disk Creator and the alternate 12.04.1 64 bit ISO. I get a grub menu in text mode (which meens it did start in efi mode) with install options / test options. But when I start any of these, I simply get a black screen (no cursor, neither mouse nor text-mode cursor). I tried removing the 'quiet' option and adding nomodeset and acpi=off, but it didn't do any good. So this is the same result as for the LiveCD. [2012-10-01] I have tried with a version of the secure remix version via usb-creator-gtk. The boot on the USB key has the same symptoms. Boot in EFI mode is impossible (I have menu but whatever entry I choose, I get the blank screen problem). The boot in BIOS mode works, I did the install. Then I used boot-repair to try installing grub-efi and get a system that would boot in efi mode. But I can't boot this system, because the EFI firmware doesn't seem to detect that sda contains a valid efi partition. Here is the resulting boot-info Boot info 1253554 [2012-10-01] Today, I have reinstalled the pre-shipped version of windows 7, and then installed ubuntu from a secure-remix iso dumped on USB flash drive vie usb-creator-gtk booted in BIOS mode. When install ended, I said "continue testing" then I used boot-repair to try get the bootloader installed. Now, when I boot the tablet, I get the grub menu, it can chainload windows 7 flawlessly. But when I try to start one of the ubuntu options I get the same old blank screen. Here is the new boot-info: Boot info 1253927 [2012-10-01] I tried installing the 3.3 kernel by chrooting a live usb boot (secure remix again) into the installed system. Same symptoms. I feel the key to this is that the device's efi firmware (which is EFI v2.0) would expose the graphics hardware in a way that prevents the kernel to initialize it, and thus prevents it from booting (the kernel stops all drive access just after the screen turns kind of very dark purple). Here is some info on the UEFI firmware as given by rEFInd: EFI revision: 2.00 Platform: x86_64 (64 bit) Firmware: American Megatrends 4.635 Screen Output: Graphics Output (UEFI), 800x600 [2012-10-08] This week end I tried loading the kernel with elilo. Eventhough I didn't have more luck on booting the kernel, elilo gives more info when loading the kernel. I think the next step is trying to load a kernel with EFI stub directly.

  Read the article

• How can a usb be detected but not show up anywhere?

  - by George Mauer

  I started the morning by trying to create a bootable usb using a 2gb stick and the startup disk creator. It seemed to run through the whole process just fine until it got to a screen that read something like "Creating memory partion" and which sat on 100% for about 45 minutes before I hit cancel and removed the usb stick. Now the usb stick is not being detected as storage or...anything (even on my windows pc) though it does show up in the syslog. Allow me to demonstrate. We start with the usb not plugged in: [georgemauer@ubuntu:~]$ sudo fdisk -l (04-04 16:01) Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x994bdc0f Device Boot Start End Blocks Id System /dev/sda1 2048 27650047 13824000 27 Hidden NTFS WinRE /dev/sda2 * 27650048 27854847 102400 7 HPFS/NTFS/exFAT /dev/sda3 27854848 976771119 474458136 7 HPFS/NTFS/exFAT I plug in the usb: [georgemauer@ubuntu:~]$ tail -f /var/log/syslog ***Snip*** Apr 4 15:01:18 ubuntu wpa_supplicant[1136]: WPA: Group rekeying completed with 00:24:36:ad:e7:3f [GTK=TKIP] Apr 4 15:02:29 wpa_supplicant[1136]: last message repeated 3 times Apr 4 15:02:29 ubuntu kernel: [22122.788133] usb 2-1: new high speed USB device number 13 using ehci_hcd Apr 4 15:02:29 ubuntu kernel: [22122.923873] scsi10 : usb-storage 2-1:1.0 Apr 4 15:02:29 ubuntu mtp-probe: checking bus 2, device 13: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-1" Apr 4 15:02:30 ubuntu mtp-probe: bus: 2, device: 13 was not an MTP device Apr 4 15:02:30 ubuntu kernel: [22123.926154] scsi 10:0:0:0: Direct-Access GENERIC USB Mass Storage 1.00 PQ: 0 ANSI: 2 Apr 4 15:02:30 ubuntu kernel: [22124.105118] sd 10:0:0:0: Attached scsi generic sg1 type 0 Apr 4 15:02:30 ubuntu kernel: [22124.108212] sd 10:0:0:0: [sdb] Attached SCSI removable disk but then: [georgemauer@ubuntu:~]$ ls /mnt -alF (04-04 16:02) total 8 drwxr-xr-x 2 root root 4096 2011-04-21 12:51 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ [georgemauer@ubuntu:~]$ ls /media -alF (04-04 16:03) total 8 drwxr-xr-x 2 root root 4096 2012-04-04 12:18 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ What could be going on and how do I recover my usb key?

  Read the article

• Why is USB-sticks so much slower than Solid State Drives?

  - by Jonas

  From what I understand, USB flash memory and Solid State Drives are based on similar technologies, NAND flash memory. But USB-sticks is usually quite slow with a read and write speed of 5-10MB per second while Solid State Drives usually is very fast, usually 100-570MB per second. Why are Solid State Drives so much faster than USB-sticks? And why isn't USB-sticks faster than 5-10MB per second? Is it simply that SSD-drives uses parallel access to the NAND flash memory or are there other reasons?

  Read the article

• How to nmot show any prompts when inserting a USB drive in Windows?

  - by jasondavis

  1) I just found a really interesting program that allows me to use a USB drive as a windows login key. It is called Rohos Logon Key. IF I remobve my USB drive/key from the PC then I can have the PC lock or hibernate or any other option, I have been looking for such a solution for many years but never knew one existed until this and it works much better then I imagined. I do have a couple minor issues though (im using Windows 7 pro). When I remove and then re-insert my USB key, windows prompts me with this dialog here... Generally when I get this I just click on "Continue without scanning" however I am looking for a solution to just make it not even show this at all, is it possible to disable it from showing? 2) I also get this dialog as well when I insert USB drives/key... Would it be possible to not show this as well or have it pick an option by default or anything really?

  Read the article

• How can I pin point a USB file transfer bottleneck in Unix?

  - by HankHendrix

  I'm experiencing very slow data transfer speeds over USB 2.0 on my nix box and was wondering how I can pin-point the cause of the problem. I've looked into iotop and top but the cpu and mem figures look normal (compared to guides I have checked). The box which is affected is Ubuntu 12.04 32bit Server running on an Asus EEE 701 2G model and I am transferring from the OS over USB 2.0 to an external HDD (which transfers at 30MB/s+ on Windows 7 on other machine). I get rsync write speeds of 1MB/s from OS to USB HDD which seems ridiculously slow. These speeds are consistent with other USB HDDs and sticks.

  Read the article

• Is there a USB 3.0 memory stick / thumb drive?

  - by jasondavis

  The new PC I just finished building has USB 3.0 support. I use a USB stick/thumb drive all the time on my PC for stuff, is there an equivalent available anywhere for USB 3.0? Please list one product per post, and provide a link to the manufacturer's product page. Also see the eSATA version of this question.

  Read the article

• How to stop any dialog windows from showing when inserting a USB drive in Windows?

  - by jasondavis

  1) I just found a really interesting program that allows me to use a USB drive as a windows login key. It is called Rohos Logon Key. IF I remobve my USB drive/key from the PC then I can have the PC lock or hibernate or any other option, I have been looking for such a solution for many years but never knew one existed until this and it works much better then I imagined. I do have a couple minor issues though (im using Windows 7 pro). When I remove and then re-insert my USB key, windows prompts me with this dialog here... Generally when I get this I just click on "Continue without scanning" however I am looking for a solution to just make it not even show this at all, is it possible to disable it from showing? 2) I also get this dialog as well when I insert USB drives/key... Would it be possible to not show this as well or have it pick an option by default or anything really?

  Read the article

• Problem with reformatting Sandisk read-only USB drive

  - by dimas

  Hi everyone I have a problem reformatting my USB drive. Its showing this error message whenever I tried to reformat it using gparted: Parted 0.11.0 --enable-libparted-dmraid Libparted 2.3 Format /dev/sdb1 as ntfs 00:00:01 ( ERROR ) calibrate /dev/sdb1 00:00:01 ( SUCCESS ) path: /dev/sdb1 start: 22,768 end: 31,248,383 size: 31,225,616 (14.89 GiB) set partition type on /dev/sdb1 00:00:00 ( ERROR ) libparted messages ( INFO ) Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Can't write to /dev/sdb, because it is opened read-only. Unable to open /dev/sdb read-write (Read-only file system). /dev/sdb has been opened read-only. Reason I wanted to reformat it is because it just suddenly stopped working when I was transferring files from my pc and also it erased every content that was saved in the usb drive. I tried various tutorials on the net regarding this however I can't find a solution on how to make a usb drive change its read-only property to read-write or anything that would enable me to reformat this usb drive. I have also checked this link format read-only USB drive but this one doesn't have a solution. Also am attempting to do this on Ubuntu 12.04.

  Read the article

• USB Flash Drive not Detected on 12.10 x64

  - by Falguni Roy

  My Mediatek usb flash drive is not get detected. The o/p of lsusb falguni@falguni-M61PME-S2P:~$ lsusb Bus 002 Device 002: ID 0e8d:0003 MediaTek Inc. Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub and the o/p of usb-devices falguni@falguni-M61PME-S2P:~$ usb-devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:02.1 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub But in 12.04, the o/p of usb-devices was: falguni@falguni-M61PME-S2P:~$ usb-devices T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh=10 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:02.1 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh=10 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev=03.05 S: Manufacturer=Linux 3.5.0-18-generic ohci_hcd S: Product=OHCI Host Controller S: SerialNumber=0000:00:02.0 C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=02(commc) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=0e8d ProdID=0003 Rev=02.00 S: Manufacturer=MediaTek Inc S: Product=MT6235 C: #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_acm I: If#= 1 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=01 Driver=cdc_acm It was working fine in 12.04. Now after upgrading to 12.10 the problem started. Where is the problem and how to solve it?

  Read the article

• Windows XP mounting USB drive to same letter as previously mapped network drive

  - by GAThrawn

  Why does Windows always mount a USB drive as the next drive letter after the last physical drive, even when that letter is already taken by a mapped drive, and is there any way to improve this behaviour? What happens is I tend to use a few different flash drives on my PC, as well as having both a Blackberry and a personal phone that mount as USB drives when I plug them in to charge. Being on a corporate PC I also have a number of mapped network drives (some set by login script, some set as persistent mappings in my profile). When I first login I'll have drive letters like this: C: - Local Drive D: - DVD Drive G: - Login script mapped drive J: - Login script mapped drive When I plug the Blackberry in it'll mount two drives (one for onboard storage, one for the SD card) as E: and F:. If I then plug in another USB drive it will mount as G:, even though that's already taken by a network mapped drive. This leaves me with the following drives: C: - Local Drive D: - DVD Drive E: - USB drive (Blackberry) F: - USB drive (Blackberry) G: - Login script mapped drive [G: - USB drive - mounted but not visible in Explorer or command prompt] J: - Login script mapped drive I then have to go into Disk Management, find the new USB drive that's mounted to G: and re-assign it to another letter eg Z:, once this is done Auto-Play detects it and throws up its normal dialog, and its browseable in Explorer. While this is OK to do if you only use one or two USB drives and have admin access to your PC with your login account, its a total pain in the proverbial if you regularly use a whole load of different USB devices, and corporate policy means you have one account for your normal login (that only has User access to workstations), but have to use a different account for any privileged action. I realize that one possible reason for this is the difference between hardware which is mounted and assigned drive letters at the systen level, and mapped drives which are done at the user level. For USB devices that are already plugged in before login, then obviously they're mounted before Windows knows what network drives may be mapped. However if you plug the USB devices in after you're fully logged in and have drives mapped then Windows must know which letters are available?

  Read the article

• [Mac OS X] Terratec Cinergy Hybrid T USB XS is not recognized anymore

  - by Gabble

  I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. 1) it is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) 2) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. 3) reset the PRAM. Nope. 4) checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. ============= I need to say that: a) the device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause) b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me… Thanks in advance for any help you will offer!

  Read the article

• Terratec Cinergy Hybrid T USB XS is not recognized anymore on Mac OS X

  - by Gabble

  I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. It is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. Reset the PRAM. Nope. Checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. I need to say that: a) The device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause). b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me. Thanks in advance for any help you will offer!

  Read the article

• Booting an Asus EeePC from a LiveCD USB stick

  - by Bryan

  I have two identical Asus EeePC netbooks that are both installed with Ubuntu. One of them was sitting on the closet shelf and the battery went completely dead. When I charged the battery and tried to boot the it, I got the "No init found" error. In trying to follow the suggested way to fix it posted here, I used the Startup Disk Creator on my Ubuntu 11.10 desktop machine to create a USB stick with a bootable Ubuntu 11.10 live CD on it (the netbook doesn't have a CD drive). I plugged the USB stick into the netbook with the init issues, went into the BIOS and selected the USB stick as the 1st choice to boot from, and did a hard restart. It then just stuck at the flashing underscore. Not knowing why it wasn't working, I tried booting my working netbook from the USB stick. When I got into the BIOS on the working netbook, I noticed the description in the boot order section for the USB device was different. On the non-working netbook, the description was SWISSBIT (the name of the USB stick) but on the working netbook it was just "Rem. Drive". I also noticed on the working netbook there was an additional option under the bootable order section that allowed me to choose which hard drive to boot from. This section showed two hard drives, one of them being my USB stick. So, rather than changing the device boot order, I selected the USB stick as the hard drive to boot from first and it worked like a champ - I was able to boot into the LiveCD on the USB stick. Seems to me the working netbook is seeing the LiveCD USB stick as a hard drive, where-as the non-working netbook is seeing it as a plain ol' USB stick. The BIOS is the exact same version on both netbooks... any idea why it works on one and not on the other?

  Read the article

• How to remove iso 9660 from USB?

  - by a_m0d

  I have somehow managed to write an iso 9660 image onto my USB drive, which makes all my computer think that the device is actually a CD. I have tried various methods of removing this partition, but nothing seems to work. I have tried fdisk, which says $ fdisk -l /dev/sdb Cannot open /dev/sdb parted crashes when I try to use it on this device. I have even tried $ dd if=/dev/zero of=/dev/sdb but it just hangs with no output (either on screen or on disk). However, when I plug the USB in, it does mount, and I can view (but not edit) the files on it. edit: now the result is $ dd if=/dev/zero of=/dev/sdb dd: opening `/dev/sdb': Read-only file system I have also tried re-formatting it on Windows, but it gets to the end of the format process and then says "Couldn't format the drive". How can I remove this partition and get my whole USB drive back to normal again? EDIT 1: Trying a simple mkfs doesn't work: $ sudo mkfs -t vfat /dev/sdb mkfs.vfat 3.0.0 (28 Sep 2008) mkfs.vfat: Will not try to make filesystem on full-disk device '/dev/sdb' (use -I if wanted) I can't do mkfs on /dev/sdb1 because there is no such partition, as shown:$ ls /dev | grep sdb sdb EDIT 2: This is the information posted by dmesg when I plug the device in:$ dmesg . . (snip) . usb 2-1: New USB device found, idVendor=058f, idProduct=6387 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: Mass Storage usb 2-1: Manufacturer: Generic usb 2-1: SerialNumber: G0905000000000010885 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access FLASH Drive AU_USB20 8.07 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb: unknown partition table sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg2 type 0 ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts CE: hpet increasing min_delta_ns to 15000 nsec This shows that the device is formatted as ISO 9660 and that it is /dev/sdb. EDIT 3: This is the message that I find at the bottom of dmesg after running cfdisk and writing a new partition table to the disk:SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts sd 17:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current] sd 17:0:0:0: [sdb] Device not ready: < ASC=0xff ASCQ=0xffASC=0xff < ASCQ=0xff end_request: I/O error, dev sdb, sector 0 Buffer I/O error on device sdb, logical block 0 lost page write due to I/O error on sdb

  Read the article

• NEC uPD720200 USB 3.0 not working on Ubuntu 12.04

  - by Jagged

  I've recently installed Ubuntu 12.04 64-bit on a HP Envy 15 1104tx. Most stuff appears to be working fine with the exception of the two USB3 ports (USB2 port works fine). I've read a lot of articles but so far have not been able to find a solution. I've tried adding 'pci=nomsi' to '/etc/default/grub' but this made no difference. Some articles suggest booting into Windows and upgrading the firmware on the uPD720200. Any body had any experience of this? Is there a way I can checked the firmware version of the NEC uPD720200 in Linux to see if there is an update available? Any help appreciated. uname -a: Linux HP-ENVY-15-1104tx 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux lshw: hp-envy-15-1104tx description: Notebook product: HP ENVY 15 Notebook PC (WF591PA#ABG) vendor: Hewlett-Packard version: 0492110000241910001420000 serial: CNF0301C79 width: 64 bits capabilities: smbios-2.6 dmi-2.6 vsyscall32 configuration: boot=normal chassis=notebook family=103C_5335KV sku=WF591PA#ABG uuid=434E4630-3330-3143-3739-60EB6906688F *-core description: Motherboard product: 1522 vendor: Hewlett-Packard physical id: 0 version: 36.35 serial: CNF0301C79 slot: Base Board Chassis Location *-firmware description: BIOS vendor: Hewlett-Packard physical id: 0 version: F.2B date: 10/12/2010 size: 1MiB capacity: 1472KiB capabilities: pci upgrade shadowing cdboot bootselect edd int13floppynec int13floppytoshiba int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int9keyboard int10video acpi usb biosbootspecification *-memory description: System Memory physical id: 13 slot: System board or motherboard size: 16GiB *-bank:0 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 0 serial: E13C4316 slot: Bottom size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 1 serial: E03C3E16 slot: Bottom size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 2 serial: 672279CC slot: On Board size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:3 description: SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) product: 9905428-043.A00LF physical id: 3 serial: 652286CC slot: On Board size: 4GiB width: 64 bits clock: 1333MHz (0.8ns) *-cpu description: CPU product: Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz vendor: Intel Corp. physical id: 1d bus info: cpu@0 version: Intel(R) Core(TM) i7 CPU Q 820 @ 1.73GHz slot: CPU size: 1199MHz capacity: 1199MHz width: 64 bits clock: 1066MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni dtes64 monitor ds_cpl vmx smx est tm2 ssse3 cx16 xtpr pdcm sse4_1 sse4_2 popcnt lahf_lm ida tpr_shadow vnmi flexpriority ept vpid cpufreq configuration: cores=4 enabledcores=4 threads=8 *-cache:0 description: L3 cache physical id: 1e slot: L3 Cache size: 8MiB capacity: 8MiB capabilities: synchronous internal write-through unified *-cache:1 description: L2 cache physical id: 20 slot: L2 Cache size: 256KiB capacity: 256KiB capabilities: synchronous internal write-through unified *-cache:2 description: L1 cache physical id: 21 slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through instruction *-cache description: L1 cache physical id: 1f slot: L1 Cache size: 32KiB capacity: 32KiB capabilities: synchronous internal write-through data *-pci:0 description: Host bridge product: Core Processor DMI vendor: Intel Corporation physical id: 100 bus info: pci@0000:00:00.0 version: 11 width: 32 bits clock: 33MHz *-pci:0 description: PCI bridge product: Core Processor PCI Express Root Port 1 vendor: Intel Corporation physical id: 3 bus info: pci@0000:00:03.0 version: 11 width: 32 bits clock: 33MHz capabilities: pci msi pciexpress pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 ioport:4000(size=4096) memory:d4100000-d41fffff ioport:c0000000(size=268435456) *-display description: VGA compatible controller product: Broadway PRO [Mobility Radeon HD 5800 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=fglrx_pci latency=0 resources: irq:58 memory:c0000000-cfffffff memory:d4100000-d411ffff ioport:4000(size=256) memory:d4140000-d415ffff *-multimedia description: Audio device product: Juniper HDMI Audio [Radeon HD 5700 Series] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:56 memory:d4120000-d4123fff *-pci:1 description: PCI bridge product: Core Processor PCI Express Root Port 3 vendor: Intel Corporation physical id: 5 bus info: pci@0000:00:05.0 version: 11 width: 32 bits clock: 33MHz capabilities: pci msi pciexpress pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 memory:d4000000-d40fffff *-usb description: USB controller product: uPD720200 USB 3.0 Host Controller vendor: NEC Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 03 width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress xhci bus_master cap_list configuration: driver=xhci_hcd latency=0 resources: irq:16 memory:d4000000-d4001fff *-generic:0 UNCLAIMED description: System peripheral product: Core Processor System Management Registers vendor: Intel Corporation physical id: 8 bus info: pci@0000:00:08.0 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:1 UNCLAIMED description: System peripheral product: Core Processor Semaphore and Scratchpad Registers vendor: Intel Corporation physical id: 8.1 bus info: pci@0000:00:08.1 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:2 UNCLAIMED description: System peripheral product: Core Processor System Control and Status Registers vendor: Intel Corporation physical id: 8.2 bus info: pci@0000:00:08.2 version: 11 width: 32 bits clock: 33MHz capabilities: pciexpress cap_list configuration: latency=0 *-generic:3 UNCLAIMED description: System peripheral product: Core Processor Miscellaneous Registers vendor: Intel Corporation physical id: 8.3 bus info: pci@0000:00:08.3 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-generic:4 UNCLAIMED description: System peripheral product: Core Processor QPI Link vendor: Intel Corporation physical id: 10 bus info: pci@0000:00:10.0 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-generic:5 UNCLAIMED description: System peripheral product: Core Processor QPI Routing and Protocol Registers vendor: Intel Corporation physical id: 10.1 bus info: pci@0000:00:10.1 version: 11 width: 32 bits clock: 33MHz configuration: latency=0 *-multimedia description: Audio device product: 5 Series/3400 Series Chipset High Definition Audio vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:55 memory:d4200000-d4203fff *-pci:2 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 1 vendor: Intel Corporation physical id: 1c bus info: pci@0000:00:1c.0 version: 05 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:17 ioport:3000(size=4096) memory:d3000000-d3ffffff ioport:d0000000(size=16777216) *-network description: Wireless interface product: Centrino Advanced-N 6200 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 35 serial: 00:27:10:40:e4:68 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=9.221.4.1 build 25532 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:54 memory:d3000000-d3001fff *-pci:3 description: PCI bridge product: 5 Series/3400 Series Chipset PCI Express Root Port 2 vendor: Intel Corporation physical id: 1c.1 bus info: pci@0000:00:1c.1 version: 05 width: 32 bits clock: 33MHz capabilities: pci pciexpress msi pm normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:16 ioport:2000(size=4096) memory:d2000000-d2ffffff ioport:d1000000(size=16777216) *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 60:eb:69:06:68:8f size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=10.161.0.147 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:57 memory:d2000000-d203ffff ioport:2000(size=128) *-usb description: USB controller product: 5 Series/3400 Series Chipset USB2 Enhanced Host Controller vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 05 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:20 memory:d4205800-d4205bff *-pci:4 description: PCI bridge product: 82801 Mobile PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: a5 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list *-isa description: ISA bridge product: Mobile 5 Series Chipset LPC Interface Controller vendor: Intel Corporation physical id: 1f bus info: pci@0000:00:1f.0 version: 05 width: 32 bits clock: 33MHz capabilities: isa bus_master cap_list configuration: latency=0 *-storage description: RAID bus controller product: 82801 Mobile SATA Controller [RAID mode] vendor: Intel Corporation physical id: 1f.2 bus info: pci@0000:00:1f.2 logical name: scsi0 version: 05 width: 32 bits clock: 66MHz capabilities: storage msi pm bus_master cap_list emulated configuration: driver=ahci latency=0 resources: irq:45 ioport:5048(size=8) ioport:5054(size=4) ioport:5040(size=8) ioport:5050(size=4) ioport:5020(size=32) memory:d4205000-d42057ff *-disk description: ATA Disk product: OCZ-VERTEX3 physical id: 0.0.0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: 2.15 serial: OCZ-0350P6H316X5KUQE size: 223GiB (240GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000592dd *-volume:0 description: EXT4 volume vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 logical name: /dev/sda1 logical name: / version: 1.0 serial: e741f18c-cfc5-4bce-b1e7-f80e517a3a22 size: 207GiB capacity: 207GiB capabilities: primary bootable journaled extended_attributes large_files huge_files dir_nlink recover extents ext4 ext2 initialized configuration: created=2012-06-15 06:49:27 filesystem=ext4 lastmountpoint=/ modified=2012-06-14 21:23:42 mount.fstype=ext4 mount.options=rw,relatime,errors=remount-ro,user_xattr,barrier=1,data=ordered mounted=2012-07-10 16:18:20 state=mounted *-volume:1 description: Extended partition physical id: 2 bus info: scsi@0:0.0.0,2 logical name: /dev/sda2 size: 15GiB capacity: 15GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume description: Linux swap / Solaris partition physical id: 5 logical name: /dev/sda5 capacity: 15GiB capabilities: nofs *-serial UNCLAIMED description: SMBus product: 5 Series/3400 Series Chipset SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 05 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:d4205c00-d4205cff ioport:5000(size=32) *-pci:1 description: Host bridge product: Core Processor QuickPath Architecture Generic Non-Core Registers vendor: Intel Corporation physical id: 101 bus info: pci@0000:ff:00.0 version: 04 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: Core Processor QuickPath Architecture System Address Decoder vendor: Intel Corporation physical id: 102 bus info: pci@0000:ff:00.1 version: 04 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: Core Processor QPI Link 0 vendor: Intel Corporation physical id: 103 bus info: pci@0000:ff:02.0 version: 04 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: Core Processor QPI Physical 0 vendor: Intel Corporation physical id: 104 bus info: pci@0000:ff:02.1 version: 04 width: 32 bits clock: 33MHz *-pci:5 description: Host bridge product: Core Processor Integrated Memory Controller vendor: Intel Corporation physical id: 105 bus info: pci@0000:ff:03.0 version: 04 width: 32 bits clock: 33MHz *-pci:6 description: Host bridge product: Core Processor Integrated Memory Controller Target Address Decoder vendor: Intel Corporation physical id: 106 bus info: pci@0000:ff:03.1 version: 04 width: 32 bits clock: 33MHz *-pci:7 description: Host bridge product: Core Processor Integrated Memory Controller Test Registers vendor: Intel Corporation physical id: 107 bus info: pci@0000:ff:03.4 version: 04 width: 32 bits clock: 33MHz *-pci:8 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Control Registers vendor: Intel Corporation physical id: 108 bus info: pci@0000:ff:04.0 version: 04 width: 32 bits clock: 33MHz *-pci:9 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Address Registers vendor: Intel Corporation physical id: 109 bus info: pci@0000:ff:04.1 version: 04 width: 32 bits clock: 33MHz *-pci:10 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Rank Registers vendor: Intel Corporation physical id: 10a bus info: pci@0000:ff:04.2 version: 04 width: 32 bits clock: 33MHz *-pci:11 description: Host bridge product: Core Processor Integrated Memory Controller Channel 0 Thermal Control Registers vendor: Intel Corporation physical id: 10b bus info: pci@0000:ff:04.3 version: 04 width: 32 bits clock: 33MHz *-pci:12 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Control Registers vendor: Intel Corporation physical id: 10c bus info: pci@0000:ff:05.0 version: 04 width: 32 bits clock: 33MHz *-pci:13 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Address Registers vendor: Intel Corporation physical id: 10d bus info: pci@0000:ff:05.1 version: 04 width: 32 bits clock: 33MHz *-pci:14 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Rank Registers vendor: Intel Corporation physical id: 10e bus info: pci@0000:ff:05.2 version: 04 width: 32 bits clock: 33MHz *-pci:15 description: Host bridge product: Core Processor Integrated Memory Controller Channel 1 Thermal Control Registers vendor: Intel Corporation physical id: 10f bus info: pci@0000:ff:05.3 version: 04 width: 32 bits clock: 33MHz *-battery description: Lithium Ion Battery product: NK06053 vendor: SMP-ATL24 physical id: 1 slot: Primary capacity: 4800mWh configuration: voltage=11.1V lspci: 02:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Hewlett-Packard Company Device 1522 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at d4000000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd lsusb (with thumb drive plugged into USB3 port): Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 5986:01d0 Acer, Inc Bus 001 Device 004: ID 03f0:231d Hewlett-Packard

  Read the article

• Hybrid USB Install Method - netboot and iso

  - by Samus Arin

  I was following the steps here ("Preparing Files for USB Memory Stick Booting") https://help.ubuntu.com/10.04/installation-guide/i386/boot-usb-files.html to create a installation usb drive for 12.1. The very first paragraph of the article states "The second is to also copy a CD image onto the USB stick and use that as a source for packages, possibly in combination with a mirror." However, the only instructions mentioned regarding an iso image is to simply copy one somewhere on the drive (after its been made bootable and syslinux, vmlinuz and initrd.gz installed/copied): "you should now copy an Ubuntu ISO image onto the stick." I thought it strange there where no configuration steps for "pointing" the kernel to the iso (like a line in syslinux.cfg or a boot: option or something), but went ahead with the install anyway. I don't think the iso was used at all, it appeared that all the OS files where downloaded during the install process. Therefore, I was wondering if anyone knew how to use this local iso image in this particular installation technique (I know the image can be installed with dd, but thats a different technique), b/c I need to reinstall (I installed unity, but it's wayy to much for my little Atom based netbook) ? Thank you.

  Read the article

• Accessing hardware via USB by proprietary windows software using Wine

  - by Carlos Eugenio Thompson Pinzón

  I have this proprietary software that access some hardware using USB. Over a year ago I tried to install it on a Ubuntu OS using Wine (the program is written for Windows). The UI seemed to work just fine but it had no access to the USB port. Back then I had to license a Windows copy in order to get the job done. Now, that Windows version we where using is deprecated and it is not longer available and available versions cost trice as much. So it is time to give Linux another try. How can I ensure that the USB is available for a Wine application? Neither the application nor the hardware install any driver, the app just pool all available USB drivers and make a handshake if it recognizes that the hardware is present. I want to minimize the test cases before abandoning Linux one more time. Update I've just tried again (with the hope an upgrade was made from last year), and it is not working. The proprietary windows app is not finding the hardware.

  Read the article

• One of the partion on a usb harddisk cannot automount

  - by holmescn

  It is a very strange problem. My usb harddisk has four partitions, one is primary, the other three are logical (contained within an extended partition). When I plug in the disk, three of the partitions are mounted automatically except one--the first logical partition in the extended partition. Initially I thought it is the problem of system (at that time I used Mint). But after I change to Ubuntu 12.04, the problem wasn't solved. I don't want to add a rule in fstab, and I want to know what happened. The disk is fine, and the partition can be accessed in Windows and mounted manually. result of dmesg | tail: [100933.557649] usb 2-1.2: new high-speed USB device number 4 using ehci_hcd [100933.651891] scsi8 : usb-storage 2-1.2:1.0 [100934.649047] scsi 8:0:0:0: Direct-Access SAMSUNG PQ: 0 ANSI: 0 [100934.650963] sd 8:0:0:0: Attached scsi generic sg2 type 0 [100934.651342] sd 8:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [100934.651977] sd 8:0:0:0: [sdb] Write Protect is off [100934.651989] sd 8:0:0:0: [sdb] Mode Sense: 03 00 00 00 [100934.652836] sd 8:0:0:0: [sdb] No Caching mode page present [100934.652848] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.655354] sd 8:0:0:0: [sdb] No Caching mode page present [100934.655367] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.734652] sdb: sdb1 sdb3 < sdb5 sdb6 sdb7 > [100934.737706] sd 8:0:0:0: [sdb] No Caching mode page present [100934.737725] sd 8:0:0:0: [sdb] Assuming drive cache: write through [100934.737731] sd 8:0:0:0: [sdb] Attached SCSI disk result of parted -l: Model: SAMSUNG (scsi) Disk /dev/sdb: 320GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 21.5GB 21.5GB primary ntfs 3 21.5GB 320GB 299GB extended lba 5 21.5GB 129GB 107GB logical ntfs 6 129GB 236GB 107GB logical ntfs 7 236GB 320GB 83.8GB logical ntfs

  Read the article

• Trouble installing Pokerstars on a Live USB without Persistence through WINE

  - by Ricky Foster

  I need to install any form of Texas Hold Em' on a Lubuntu Live USB that doesn't have persistence. I was able to download PokerStars.net by emulating the .exe (a windows type file) using WINE for Linux (Lubuntu). But, when I try to install, I have no room. The only place on the Live USB is in the root folder which is set to read-only. Is there any way I can change the read only properties of the Live USB while it's in use? So, to recap. I am running Lubuntu 13.04 and can't start in Persistent mode. When I start normally everything worked fine. I proceeded to Chromium and successfully downloaded Wine and the Pokerstars.exe. I right clicked the downloaded fiel then clicked Wine, the installer loaded fine. There are about 8 different disk icons and only the one containing system files is active. Is there any way I can use the terminal to install it to Root. Thanks in advance for your answer/alternate method (without having to buy another USB to install it to).

  Read the article

• USB flash module giving errors

  - by vshenoy

  Hi, I have a SATA USB flash module which was earlier running a 2.4 linux kernel (2.4.36.6) and on which now I am trying to install ubuntu server 10.04.1 LTS. I have two such USB flash modules and on one of them the installation process itself giving these errors: sd 4:0:0:0 [sda] Device not ready sd 4:0:0:0 [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 4:0:0:0 [sda] Sense Key : Not Ready [current] sd 4:0:0:0 [sda] Add. Sense: Medium not present sd 4:0:0:0 [sda] CDB: Write(10): 2a 00 00 05 48 02 00 00 04 00 end_request: I/O error, dev sda, sector 46114 usb 1-1: reset high speed USB device using ehci_hcd and address 2 Buffer I/O error on device sda1, logical block 172033 lost page write due to I/O error on sda1 Buffer I/O error on device sda1, logical block 172034 lost page write due to I/O error on sda1 on the other the installation is successful, but after a day or two of running the machine hangs because of kernel spewing these messages: Remounting filesystem read-only EXT2-fs error (device sda1): read_block_bitmap: Cannot read block [bitmap - block_group = 105, block_bitmap = 860161] EXT2-fs error (device sda1): ext2_get_inode: unable to read inode block - inode=13083, block=24683 ext2_free_inode: bit already cleared for inode 83966 and the machine needs to be hard rebooted. On both the systems SCSI emulation with usb_storage driver is being used to detect the module. Here is the output of /proc/scsi/scsi on 2.4: # cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 02 and on 2.6: # cat /proc/scsi/scsi Attached devices: Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: TS Model: UFM Rev: 1100 Type: Direct-Access ANSI SCSI revision: 00 i.e. only 'ANSI SCSI revision:' is shown as different, although I am not sure if this can cause any problem. Really appreciate if someone can point as to how to debug this issue or any mailing list where I can further ask questions about this.

  Read the article

• Ubuntu Tools for recovering data from damaged USB Flash Drive ~ 10 Gb

  - by PREDA LUCIAN

  I have technical issues with my USB Flash Drive - JetFlash®V15 (TS16GJFV15) It's very critical situation because I can not see the data from it and I should get a way to recover them ASAP. So, in general, I have connected Non-stop that USB Flash Disk at my laptop. Was appear Power surges and when I was coming back, I saw that problem with it. Details regarding JetFlash®V15 (in present): - when I connect it on USP slot, the led is working intermittent and later on remain with constant light. - if I inspect the computer drivers, I found "Generic USB Flash Disk" (when the stick it's connected). - if I inspect "Properties", I can see next details: --- Type: unknown (application/octet-stream) --- Size: unknown --- Volume: unknown --- Accessed: unknown --- Modified: unknown I inspected that stick on 2 different computers (as well in different different USB Ports) and was the same problem, I can not see the content. I was checking with Windows 7 and Ubuntu 10.04 OS, but without success. With both OS was working before this issue. I'll appreciate an answer which will solve the problem, not an answer which will certify the problem. What I have to do, to recover the information form it (nearly 10 Gb)? I'm looking forward to be guided from a technical expert.

  Read the article

• Why is my USB data transfer so slow?

  - by Dave M G

  Whenever I do any kind of file transfer using USB, whether to a USB stick, or with my Android phone, or anything else, it is ridiculously slow. It says 59.8 KB/sec, which would be an awesome speed if this were 1991 and I was using a modem to dial up to my local BBS. Surely USB technology is better than that...? 37 seconds to move less data than the equivelent of 1 MP3 file? Also, regardless of what it says about speed and time, the reality is much, much slower. I routinely see it say something like "37 seconds left" and have to wait for minutes. Sometimes, if I want to move large amounts of files, it can say it will take 8 hours or more. Is this normal? My computer may not be the most awesome on the market, and about a year old, but it's an i5 with 4GB RAM and modern components, so surely this isn't the hardware's fault. What can I do to get better USB data transfer performance? Also, I did look at this question, but my newbie eyes don't see anything that look like an actual solution, just a lot of discussion about what transfer rates could or should be. Update: As requested in the comments, I've generated a whole bunch of output from the command line, and put it on Ubuntu Pastebin. Please see it here.

  Read the article

• Why are USB 2.0 devices crashing my system?

  - by BenAlabaster

  Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic baby-ATX motherboard with no identifying markings. CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. There's one stamp on the motherboard that says "Rev.B". On board it has 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. It has an 80Gb Western Digital hard drive freshly formatted and built with Windows XP Professional with Service Pack 3 and all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 crashes the machine as soon as it starts up). It's got a Daytek MV150 15" touch screen running through the VGA and COM1 with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem If I hook any USB 2.0 devices to this machine, it hangs the whole machine and I have to hard boot it to get it back up. Workarounds found I can plug the same devices into the on board USB 1.0 connectors and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions I've tried disabling all the on board devices that I'm not using - such as the on board LAN, the second COM port, the AGP connector etc. through the BIOS in an (perhaps misguided or futile) attempt to reduce the power consumption... I don't think it had any effect but it didn't do any harm. I was wondering if the PSU wattage just isn't enough to drive the USB 2.0 devices; I've seen this suggested but haven't found any confirmation that this could really be an issue - nor have I found a way to work around this issue - if indeed it is one. Any ideas? The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference. I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself. Other thoughts Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >