Search Results

Search found 92087 results on 3684 pages for 'usb server'.

Page 10/3684 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

  • Kingston SD reader not working for USB3

    - by user1146334
    I have a Kingston 4-in-1 Multimedia reader. When my PC was formatted with Win7 it worked fine. I decided to change to Ubuntu 14.04 and now it doesn't work. If I plug it into one of the USB2 ports it works fine, but whenever I plug it into one of the USB3 ports, it thinks about it for a minute and then dies. Here's the output of dmesg when it dies [110262.148656] usb 4-1: new SuperSpeed USB device number 3 using xhci_hcd [110262.170330] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [110262.266379] usb 4-1: New USB device found, idVendor=11b0, idProduct=6348 [110262.266386] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [110262.266390] usb 4-1: Product: USB3.0 Media Reader [110262.266394] usb 4-1: Manufacturer: Kingston [110262.266398] usb 4-1: SerialNumber: 08735314400198 [110262.272929] usb-storage 4-1:1.0: USB Mass Storage device detected [110262.273239] scsi15 : usb-storage 4-1:1.0 [110263.290056] scsi 15:0:0:0: Direct-Access FCR-HS3 -0 1.00 PQ: 0 ANSI: 4 [110263.306622] scsi 15:0:0:1: Direct-Access FCR-HS3 -1 1.00 PQ: 0 ANSI: 4 [110263.323292] scsi 15:0:0:2: Direct-Access FCR-HS3 -2 1.00 PQ: 0 ANSI: 4 [110263.339858] scsi 15:0:0:3: Direct-Access FCR-HS3 -3 1.00 PQ: 0 ANSI: 4 [110263.340332] sd 15:0:0:0: Attached scsi generic sg3 type 0 [110263.340706] sd 15:0:0:1: Attached scsi generic sg4 type 0 [110263.340850] sd 15:0:0:2: Attached scsi generic sg5 type 0 [110263.340975] sd 15:0:0:3: Attached scsi generic sg6 type 0 [110264.651847] sd 15:0:0:1: [sde] 31116288 512-byte logical blocks: (15.9 GB/14.8 GiB) [110264.667049] sd 15:0:0:1: [sde] Write Protect is off [110264.667055] sd 15:0:0:1: [sde] Mode Sense: 2f 00 00 00 [110264.682767] sd 15:0:0:1: [sde] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [110264.694975] sd 15:0:0:2: [sdf] Attached SCSI removable disk [110264.697933] sd 15:0:0:3: [sdg] Attached SCSI removable disk [110264.729918] sd 15:0:0:0: [sdd] Attached SCSI removable disk [110264.754189] sde: sde1 [110264.760114] sd 15:0:0:1: [sde] Attached SCSI removable disk [110275.377368] usb 4-1: reset SuperSpeed USB device number 3 using xhci_hcd [110275.398453] usb 4-1: Parent hub missing LPM exit latency info. Power management will be impacted. [110275.436592] xhci_hcd 0000:05:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802e4fb9980 [110275.436600] xhci_hcd 0000:05:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff8802e4fb99c0 [110277.263444] usb 4-1: USB disconnect, device number 3

    Read the article

  • Auto backup a user folder to a usb when usb is plugged in

    - by Azztech Computers
    I'm a computer technician and help customers everyday with their computers and smartphones and have a really basic (i think) request but dont know how to go about it. Customer always come in with broken phones, water damage, needing updates, or just want me to backup their information. I currently have a program that i use when i backup their computers it backups their iOS folder C:\Users\USER\AppData\Roaming\Apple Computer\MobileSync\Backup but what i want is a quick easy way to do this in customers houses. What i require is a way when i plug in a USB drive it AUTOMATICALLY searches for the folder and starts transferring the folder to a predefined folder on the USB drive. This was I can just plug it in and begin work on their computer or phone without the risk of losing their information. I'm sure there is a .bat/.ini file i could use but wondering if someone has already done this or something similar as I would need it to search all the USER folders not just the one I'm logged into. Thanks in advance

    Read the article

  • SharePoint 2010 – SQL Server has an unsupported version 10.0.2531.0

    - by Jeff Widmer
    I am trying to perform a database attach upgrade to SharePoint Foundation 2010. At this point I am trying to attach the content database to a Web application by using Windows Powershell: Mount-SPContentDatabase -Name <DatabaseName> -DatabaseServer <ServerName> -WebApplication <URL> [-Updateuserexperience] I am following the directions from this TechNet article: Attach databases and upgrade to SharePoint Foundation 2010.  When I go to mount the content database I am receiving this error: Mount-SPContentDatabase : Could not connect to [DATABASE_SERVER] using integrated security: SQL server at [DATABASE_SERVER] has an unsupported version 10.0.2531.0. Please refer to “http://go.microsoft.com/fwlink/?LinkId=165761” for information on the minimum required SQL Server versions and how to download them. At first this did not make sense because the default SharePoint Foundation 2010 website was running just fine.  But then I realized that the default SharePoint Foundation site runs off of SQL Server Express and that I had just installed SQL Server Web Edition (since the database is greater than 4GB) and restored the database to this version of SQL Server. Checking the documentation link above I see that SharePoint Server 2010 requires a 64-bit edition of SQL Server with the minimum required SQL Server versions as follows: SQL Server 2008 Express Edition Service Pack 1, version number 10.0.2531 SQL Server 2005 Service Pack 3 cumulative update package 3, version number 9.00.4220.00 SQL Server 2008 Service Pack 1 cumulative update package 2, version number 10.00.2714.00 The version of SQL Server 2008 Web Edition with Service Pack 1 (the version I installed on this machine) is 10.0.2531.0. SELECT @@VERSION: Microsoft SQL Server 2008 (SP1) - 10.0.2531.0 (X64)   Mar 29 2009 10:11:52   Copyright (c) 1988-2008 Microsoft Corporation  Web Edition (64-bit) on Windows NT 6.1 <X64> (Build 7600: ) (VM) But I had to read the article several times since the minimum version number for SQL Server Express is 10.0.2531.0.  At first I thought I was good with the version of SQL Server 2008 Web that I had installed, also 10.0.2531.0.  But then I read further to see that there is a cumulative update (hotfix) for SQL Server 2008 SP1 (NOT the Express edition) that is required for SharePoint 2010 and will bump the version number to 10.0.2714.00. So the solution was to install the Cumulative update package 2 for SQL Server 2008 Service Pack 1 on my SQL Server 2008 Web Edition to allow SharePoint 2010 to work with SQL Server 2008 (other than the SQL Server 2008 Express version). SELECT @@VERSION (After installing Cumulative update package 2): Microsoft SQL Server 2008 (SP1) - 10.0.2714.0 (X64)   May 14 2009 16:08:52   Copyright (c) 1988-2008 Microsoft Corporation  Web Edition (64-bit) on Windows NT 6.1 <X64> (Build 7600: ) (VM)

    Read the article

  • Install SharePoint 2013 on a two server farm

    - by sreejukg
    When SharePoint 2010 was released, I published an article on how to install SharePoint on a two server farm. You can find that article from the below link. http://weblogs.asp.net/sreejukg/archive/2010/09/28/install-sharepoint-2010-in-a-farm-environment.aspx Now it is the time for SharePoint 2013. SharePoint 2013 brings lots of improvements to the topologies, but still supports two-server architecture. Be noted that “two-server architecture” is meant for small implementations with limited service applications. Refer the below link to understand more about the SharePoint architecture http://technet.microsoft.com/en-us/sharepoint/fp123594.aspx A two tier farm consists of a database server and a web/application server as follows. In this article I am going to explain how to install SharePoint in a two server farm. I prepared 2 servers, both of them joined to a domain(SP2013Domain), and in one server I installed SQL Server 2012 (Server name: SP2013_DB). Now I am going to install SharePoint 2013 in the second server (Server Name: SP2013). The following domain accounts are created for the installation.   User Account Purpose Server roles required SQLService - SQL Server service account - This account is used as the service account for SQL Server. - domain user account / local account spSetup - You will be running SharePoint setup and SharePoint products and configuration wizard using this account. -domain user account - Member of the Administrators group on each server on which Setup is run(In our case SP2013) - SQL Server login on the computer running SQL Server - Member of the Server admin SQL Server security role spDataaccess - Configure and manage server farm. This - Application pool identity for central admin website - Microsoft SharePoint Foundation Workflow Timer Service Domain user account (Other permissions will be set to this account automatically)   The above are the minimum list of accounts needed for SharePoint 2013 installation. Now you need additional accounts for services, application pool identities for web applications etc. Refer the service accounts requirements for SharePoint from the below link. http://technet.microsoft.com/en-us/library/cc263445.aspx In order to install SharePoint 2013 login to the server using setup account(spsetup). Now run the setup from the installation media. First you need to install the pre-requisites. During the installation process, the server may restart several times. The installation wizard will guide you through the installation. In the next step, you need to agree on the terms and conditions as usual. Once you click next, the installation will start immediately. The installation wizard will let you know the progress of the installation. During the installation you may receive notifications to restart the server, you need to just click the finish button so that the system will be restarted. Once all the pre-requisites are installed, you will get the success message as below. Click finish to close the dialog. Now from the media, run the setup again and this time you choose install SharePoint server. In the next screen, you need to enter the product key, and then click continue. Now you need to agree on the terms and conditions for SharePoint 2013, and click continue. Choose the file location as per your policies and click on the install now button. You will see the installation progress. Once completed, you will see the installation completed dialog. Make sure you select the run products and configuration wizard option and click close. From the start screen, click next to start the configuration wizard. You will receive warning telling you some of the services will be stopped during the installation. Select “create new server farm” radio button and click next. In the next step, you need to enter the configuration database settings. Enter the database server details and then specify the database access account. You need to specify the farm account(spdataaccess). The wizard will grant additional privileges to the account as needed. In the next step you need to specify the passphrase, you need to note this as you need this passphrase if you add additional server to the farm. In the next step, you need to enter the central administration website port and security settings. You can choose a port or just keep it as suggested by the wizard. Click next, you will see the summary of what you have been selected. Verify the selected settings and if you want to change any, just click back and change them, or click continue to start the configuration. The configuration may take some time, you can view the progress, in case of any error, you will get the log file, you need to fix any error and again start the configuration wizard. Once the configuration successful, you will see the success message. Just click finish. Now you can browse the central administration website. It is good to check the health analyzer to review whether there are any errors/warnings. No warnings/errors indicate a good installation. Two-Server architecture is the least configuration for production environments. For small firms with less number of employees can implement SharePoint 2013 using this topology and as the workload increases, they can add more servers to the farm without reconstructing everything.

    Read the article

  • SQL Server 2012 : Changes to system objects in RC0

    - by AaronBertrand
    As with every new major milestone, one of the first things I do is check out what has changed under the covers. Since RC0 was released yesterday, I've been poking around at some of the DMV and other system changes. Here is what I have noticed: New objects in RC0 that weren't in CTP3 Quick summary: We see a bunch of new aggregates for use with geography and geometry. I've stayed away from that area of programming so I'm not going to dig into them. There is a new extended procedure called sp_showmemo_xml....(read more)

    Read the article

  • SQL Server 2012 : A couple of notes about installing RC0

    - by AaronBertrand
    If you're going to install Distributed Replay Controller I've posted about this on twitter a few times, but I thought I should put it down somewhere permanent as well. When you install RC0, and have selected the Distributed Replay Controller, you should be very careful about choosing the "Add Current User" button on the following dialog (I felt compelled to embellish with the skull and crossbones): If you click this button (it may also happen for the Add... button), you may experience a little delay...(read more)

    Read the article

  • Using UDF on a USB flash drive

    - by CesarB
    After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Introducing Oracle VM Server for SPARC

    - by Honglin Su
    As you are watching Oracle's Virtualization Strategy Webcast and exploring the great virtualization offerings of Oracle VM product line, I'd like to introduce Oracle VM Server for SPARC --  highly efficient, enterprise-class virtualization solution for Sun SPARC Enterprise Systems with Chip Multithreading (CMT) technology. Oracle VM Server for SPARC, previously called Sun Logical Domains, leverages the built-in SPARC hypervisor to subdivide supported platforms' resources (CPUs, memory, network, and storage) by creating partitions called logical (or virtual) domains. Each logical domain can run an independent operating system. Oracle VM Server for SPARC provides the flexibility to deploy multiple Oracle Solaris operating systems simultaneously on a single platform. Oracle VM Server also allows you to create up to 128 virtual servers on one system to take advantage of the massive thread scale offered by the CMT architecture. Oracle VM Server for SPARC integrates both the industry-leading CMT capability of the UltraSPARC T1, T2 and T2 Plus processors and the Oracle Solaris operating system. This combination helps to increase flexibility, isolate workload processing, and improve the potential for maximum server utilization. Oracle VM Server for SPARC delivers the following: Leading Price/Performance - The low-overhead architecture provides scalable performance under increasing workloads without additional license cost. This enables you to meet the most aggressive price/performance requirement Advanced RAS - Each logical domain is an entirely independent virtual machine with its own OS. It supports virtual disk mutipathing and failover as well as faster network failover with link-based IP multipathing (IPMP) support. Moreover, it's fully integrated with Solaris FMA (Fault Management Architecture), which enables predictive self healing. CPU Dynamic Resource Management (DRM) - Enable your resource management policy and domain workload to trigger the automatic addition and removal of CPUs. This ability helps you to better align with your IT and business priorities. Enhanced Domain Migrations - Perform domain migrations interactively and non-interactively to bring more flexibility to the management of your virtualized environment. Improve active domain migration performance by compressing memory transfers and taking advantage of cryptographic acceleration hardware. These methods provide faster migration for load balancing, power saving, and planned maintenance. Dynamic Crypto Control - Dynamically add and remove cryptographic units (aka MAU) to and from active domains. Also, migrate active domains that have cryptographic units. Physical-to-virtual (P2V) Conversion - Quickly convert an existing SPARC server running the Oracle Solaris 8, 9 or 10 OS into a virtualized Oracle Solaris 10 image. Use this image to facilitate OS migration into the virtualized environment. Virtual I/O Dynamic Reconfiguration (DR) - Add and remove virtual I/O services and devices without needing to reboot the system. CPU Power Management - Implement power saving by disabling each core on a Sun UltraSPARC T2 or T2 Plus processor that has all of its CPU threads idle. Advanced Network Configuration - Configure the following network features to obtain more flexible network configurations, higher performance, and scalability: Jumbo frames, VLANs, virtual switches for link aggregations, and network interface unit (NIU) hybrid I/O. Official Certification Based On Real-World Testing - Use Oracle VM Server for SPARC with the most sophisticated enterprise workloads under real-world conditions, including Oracle Real Application Clusters (RAC). Affordable, Full-Stack Enterprise Class Support - Obtain worldwide support from Oracle for the entire virtualization environment and workloads together. The support covers hardware, firmware, OS, virtualization, and the software stack. SPARC Server Virtualization Oracle offers a full portfolio of virtualization solutions to address your needs. SPARC is the leading platform to have the hard partitioning capability that provides the physical isolation needed to run independent operating systems. Many customers have already used Oracle Solaris Containers for application isolation. Oracle VM Server for SPARC provides another important feature with OS isolation. This gives you the flexibility to deploy multiple operating systems simultaneously on a single Sun SPARC T-Series server with finer granularity for computing resources.  For SPARC CMT processors, the natural level of granularity is an execution thread, not a time-sliced microsecond of execution resources. Each CPU thread can be treated as an independent virtual processor. The scheduler is naturally built into the CPU for lower overhead and higher performance. Your organizations can couple Oracle Solaris Containers and Oracle VM Server for SPARC with the breakthrough space and energy savings afforded by Sun SPARC Enterprise systems with CMT technology to deliver a more agile, responsive, and low-cost environment. Management with Oracle Enterprise Manager Ops Center The Oracle Enterprise Manager Ops Center Virtualization Management Pack provides full lifecycle management of virtual guests, including Oracle VM Server for SPARC and Oracle Solaris Containers. It helps you streamline operations and reduce downtime. Together, the Virtualization Management Pack and the Ops Center Provisioning and Patch Automation Pack provide an end-to-end management solution for physical and virtual systems through a single web-based console. This solution automates the lifecycle management of physical and virtual systems and is the most effective systems management solution for Oracle's Sun infrastructure. Ease of Deployment with Configuration Assistant The Oracle VM Server for SPARC Configuration Assistant can help you easily create logical domains. After gathering the configuration data, the Configuration Assistant determines the best way to create a deployment to suit your requirements. The Configuration Assistant is available as both a graphical user interface (GUI) and terminal-based tool. Oracle Solaris Cluster HA Support The Oracle Solaris Cluster HA for Oracle VM Server for SPARC data service provides a mechanism for orderly startup and shutdown, fault monitoring and automatic failover of the Oracle VM Server guest domain service. In addition, applications that run on a logical domain, as well as its resources and dependencies can be controlled and managed independently. These are managed as if they were running in a classical Solaris Cluster hardware node. Supported Systems Oracle VM Server for SPARC is supported on all Sun SPARC Enterprise Systems with CMT technology. UltraSPARC T2 Plus Systems ·   Sun SPARC Enterprise T5140 Server ·   Sun SPARC Enterprise T5240 Server ·   Sun SPARC Enterprise T5440 Server ·   Sun Netra T5440 Server ·   Sun Blade T6340 Server Module ·   Sun Netra T6340 Server Module UltraSPARC T2 Systems ·   Sun SPARC Enterprise T5120 Server ·   Sun SPARC Enterprise T5220 Server ·   Sun Netra T5220 Server ·   Sun Blade T6320 Server Module ·   Sun Netra CP3260 ATCA Blade Server Note that UltraSPARC T1 systems are supported on earlier versions of the software.Sun SPARC Enterprise Systems with CMT technology come with the right to use (RTU) of Oracle VM Server, and the software is pre-installed. If you have the systems under warranty or with support, you can download the software and system firmware as well as their updates. Oracle Premier Support for Systems provides fully-integrated support for your server hardware, firmware, OS, and virtualization software. Visit oracle.com/support for information about Oracle's support offerings for Sun systems. For more information about Oracle's virtualization offerings, visit oracle.com/virtualization.

    Read the article

  • SQL SERVER – Microsoft SQL Server 2014 CTP1 Product Guide

    - by Pinal Dave
    Today in User Group meeting there were lots of questions related to SQL Server 2014. There are plenty of people still using SQL Server 2005 but everybody is curious about what is coming in SQL Server 2014.  Microsoft has officially released SQL Server 2014 CTP1 Product Guide. You can easily download the product guide and explore various learning around SQL Server 2014 as well explore the new concepts introduced in this latest version. This SQL Server 2014 CTP1 Product Guide contains few interesting White Papers, a Datasheet and Presentation Deck. Here is the list of the white papers: Mission-Critical Performance and Scale with SQL Server and Windows Server Faster Insights from Any Data Platform for Hybrid Cloud SQL Server In-Memory OLTP Internals Overview for CTP1 SQL Server 2014 CTP1 Frequently Asked Questions for TechEd 2013 North America Here is the list of slide decks: SQL Server 2014 Level 100 Deck SQL Server 2014 Mission Critical Performance LEvel 300 Deck SQL Server 2014 Faster Insights from Any Data Level Level 300 Deck SQL Server 2014 Platform for Hybrid Cloud Level 100 Deck I have earlier downloaded the Product Guide and I have yet not completed reading everything SQL Server 2014 has to offer. If you want to read what are the features which I am going to use in SQL Server 2014, you can read over here. Download Microsoft SQL Server 2014 CTP1 Product Guide Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: PostADay, SQL, SQL Authority, SQL Documentation, SQL Download, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • bootable USB / installation requirements

    - by Chris Wilson
    Originally asked on One Hundred Paper Cuts Answers thread On the official site: http://www.ubuntu.com/netbook/get-ubuntu/download The instructions for creating a bootable USB key for installing Ubuntu Netbook Remix include a line saying: "Insert a USB stick with at least 2GB of free space" I recently installed UNR on a netbook -- in fact, the one I'm using right now -- and I went ahead despite only having a 1GB USB key on hand. Everything went smoothly and installed 100% correctly. If I had waited to go out and buy a 2GB USB key I would have spent that money unnecessarily and wouldn't have been able to use the computer in the meantime. I was wondering if there's a specific rationale for requiring a 2GB USB key, or if the instructions could be changed to indicate that it can be done with only 1GB. Thanks!

    Read the article

  • Unable to enumerate USB device

    - by takeshin
    Hello, My syslog is constantly filled with messages like this: Oct 16 11:48:35 my-laptop kernel: [61470.980078] hub 1-0:1.0: unable to enumerate USB device on port 2 Oct 16 11:48:35 my-laptop kernel: [61471.192079] hub 3-0:1.0: unable to enumerate USB device on port 2 The only USB device I use is Microsoft Natural Wireless Laser Mouse 7000. The laptop model is HP dv9500, Ubuntu 10.10, but the same was in the versions before. How can I fix this? Edit: Here's the output of sudo lsusb: Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 003: ID 045e:071d Microsoft Corp. Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub All USB devices seems to be working fine. I have some problems with DVD-R and sound card, but they are not USB.

    Read the article

  • USB gets disabled when i boot in linux (ubuntu 3.5.7)

    - by Gaurav Vyas
    I have connected USB keyboard & mouse to core i7 intel processor.When i boot my system in ubuntu with kernel 3.2.21 it runs properly i.e usb keyboard & usb mouse works satisfactorily. ISSUE When i boot my system in linux(ubuntu 3.5.7) USB keyboard & usb Mouse stops working.i have to boot my system by pressing "e" and then "Enter" i.e it directly links with the hardware.Mouse doesnt get power i.e LED under my optical mouse doesnt glow. kindly help me.

    Read the article

  • 'Invalid or corrupt kernel image' error while booting from USB stick

    - by steve
    I got the Ubuntu 11.10 32-bit edition and i used Unetbootin to write the ISO to a usb stick.After that i tried to boot from the stick,having changed the BIOS boot settings,and when the first interface shows up with the choices of istallation,whatever choice i select i got the message"invalid or corrupt kernel image".I use a netbook with windows 7 on it.I tried different usb sticks but same again.I also tried Universal USB installer instead of Unetbootin but same again.Any idea of what happens?I am using ASUS 1000H.The USB doesn't work in one more PC i tried to,but i also tried a second USB to both of the two computers and same again. I downloaded the ISO image once again and follow the same procedure but same again

    Read the article

  • Save to Hard Drive instead of bootable USB

    - by WAM
    I followed the instructions on the Ubuntu website on how to put Ubuntu 12.04 on a USB and make it a bootable USB stick for windows. It worked fine and I can boot up and run Ubuntu, but every time I try to download software or change settings it tries to save it to the USB rather than the hard drive built into the computer. The USB doesn't have enough space so the download fails and in addition it doesn't retain setting changes so when I restart my computer all the settings return to default and anything I saved is gone. Is there any way to change things so that when I download software or change settings Ubuntu will save it to my hard drive instead of the USB?

    Read the article

  • Unable to enumerate USB device on port 2 when connecting Android phone

    - by ProfessionalAmateur
    I'm running Ubuntu 11.10 (64-bit) as a VirtualBox guest on a Win7 64-bit host. When I plug in my Android Epic4g (Galaxy S) both the host and guest see the device properly, however lsusb does not. When I run dmesg I get the following: [ 361.664219] usb 1-2: new full speed USB device number 79 using ohci_hcd [ 362.428798] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 363.313782] hub 1-0:1.0: unable to enumerate USB device on port 2 I get the same type of dmesg message with the USB 2.0 (ECHI) Controller enabled and disabled for the guest OS. I'm stuck with this one, can anyone help?

    Read the article

  • moving to a new dedicated server and need advice on the new setup

    - by Eric Martin
    I currently have a dedicated server that we have outgrown and we are moving to another server. Our current setup was a 8gb W2008R2 server running a W2008R2 IIS virtual machine using VMWare. We are moving to a 2 cpu 24 gb server with W2012 R2 on Hyper-V. On our virtual machine we are running iis 7.5 and sql server. Sql Server seems to want to eat up all the memory so I had to cap it at 2gb, which doesn't seem sufficient. My question is, when I move the virtual machine to the new server, should I create 2 virtual machines, one for sql server and one for IIS? Or should I leave them both on the same virtual machine? Or even, put the Sql Server on the dedicated server and run the IIS in the vm? I'd like some input on how this should be done, I've not got the experience needed to make the right call. Thanks!

    Read the article

  • After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports.

    - by sin
    I have a big problem! After making boot disk using rufus in usb 3.0 port, it doesn't work in another ports. I have to install windows in other PC which has usb 2.0port only! so I made usb booting disk using usb 3.0 in 3.0 port. but after that it never worked except in 3.0 ... and I could't restore my usb. I alredy fomated in cmd and others in usb3.0 port! but there is no change. and I couldn't find it in usb 2.0 port. plz help me.

    Read the article

  • Any large USB sticks with integrated card readers?

    - by Al
    I have one of Kingston's DataTraveller Micro Reader USB sticks, a fantastic memory stick with an integrated micro SD and M2 card reader. However, I've gradually filled it to the brim and am looking for a larger stick. Unfortunately, Kingston don't make them any bigger than the 4GB one that I currently have and I was hoping to go to 16GB now that they've come down in price. Does anyone know if any manufacturers make something similar: a 16GB stick with a micro SD card reader integrated (I'm not bothered about the M2 reader).

    Read the article

  • Recognition of USB drive

    - by lamcro
    I have a Motorola phone, with a MicroSD slot, which my Ubuntu machine does not recognize as a USB drive. It does know there is something there since It automatically charges my phone whenever I connect it. using the command lsusb shows it as "Motorola PCS" Is there a way to tell Ubuntu/Linux that the connected hardware is a disk drive?

    Read the article

  • Pen drive is recognizing as a USB Internet Dongle which connects to the PC. How do the Pen drive configure well in Ubuntu 12.04?

    - by Eranga Fernando
    Every time I connect my Pen drive it recognizes as more like a Dongle. The reason that I'm telling that if I connect it to the PC when I'm on the INTERNET, it will automatically copy all the files which are in the Dongle. So, I can't recognize which one is the Pen drive when I want to safely remove the device. I'm not sure whether it is the Pen drive or the Dongle..? Can anyone give me a good advice how to solve this problem?

    Read the article

  • Setting up SQL Server 2005 to use all available memory in 32bit Windows Server 2003 - and verifying

    - by Rizwan Kassim
    There are a number of questions along this line - but they either sometimes contradict each other, or don't show how to properly verify that everything is actually working - hopefully this can be comprehensive... I'm running SQL Server 2005 SP3 Standard on Windows Server 2003 R2 Standard. My server has 8GB of memory installed - my system is almost entirely used as a Database Server - there are some services running on them, but the OS + services can run within 1Gb of RAM. What I've done (please tell me if I'm doing something wrong): /3GB in the boot.ini. (To increase the amount of user-space memory available - info) /PAE in the boot.ini. (Windows claimed to be doing PAE even without this switch, somethow.) Enabled AWE in SQL Server. Enabled Lock Pages in Memory Option for users SYSTEM and Local Service. (info). SQL Server Standard doesn't seem to use this until Cumulative Update 4, which isn't installed on my server. (info) Set Min/Max Memory to : 1024Mb/5112Mb After doing all the above, we definately saw a level of improvement - but I'd like now to verify my settings, make sure that I'm making full use of the memory available. (There appeared to be a slowdown when max = 7Gb, so I edged off from that value, but it might have been just perceptual.) To verify, I checked the following levels in PerfMon : Process(sqlserv):Working Set : 76386304 SQL Server(Memory Manager) : Total Server Memory : 3538944 (I saw a doc that noted that this wasn't the full memory used by SQL Server, so I'm not sure whether to trust it) So -- my questions... Should my max be around 7Gb? If not, what should it be? Why is total server memory at 3.5G, when it's been allocated 5G? What is the proper metric for the amount of memory allocated to SQL Server? The Working Set seems a bit large... Am I possibly missing any steps in the setup? Any recommended resources on starting to tune the caching system now? Thanks

    Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >