Search Results

Search found 10756 results on 431 pages for 'zend controller'.

Page 10/431 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

  • Booting from integrated RAID controller when another RAID controller is installed in a PCIe slot

    - by Antony Scott
    I have a GA MA785GT UD3H motherboard with Windows Server 2008 R2 installed on a RAID1 using the on-board RAID controller. I have now installed a RocketRaid 2680 controller and set up a RAID5 for all my data to be stored on. Unfortunately I now cannot boot from the RAID1 anymore, the PC is trying to boot from the RAID5! Does anyone have any experience of this motherboard / RAID controller combination?

    Read the article

  • I don't get Zend_Validate_Regex working

    - by poru
    Zend_Validate_Alpha doesn't fit 100% to that what I want and I don't get Zend_Validate_Regex working. I want that the validator just allows a-z/A-Z, 0-9, _ and -. I tried to add the following to one of my inputs: addValidator('Regex', true, array('pattern' => '/^[a-zA-Z0-9_-]/')) but for example abc§$%& is a valid input says the Zend Validator. What am I doing wrong?

    Read the article

  • replace controller, add second controller, or use expander?

    - by longneck
    I have a Proliant DL380 G6 that I am re-purposing as a Hyper-V host for a new, off-site data center that will host our DR services. The server currently has a P410i controller with the 512MB BBWC module. The drives installed are SFF 6G 10K drives. I plan to add the HP 516914-B21 drive cage, which gives me 8 more SFF drives, bringing the total to 16. To get the additional 8 drives connected, I have one of three choices: Install a new controller that can support 16 drives. Install a second controller. Install a SAS expander, such as the HP 468406-B21 recommended by HP's spec sheet for my server. My question is: how do I know if I'm going hit a performance ceiling by putting 16 drives on the P410i or using the expander? And if I am, how do I select an appropriate controller? I'm not sure what specifications I should be looking at.

    Read the article

  • Problem adding second domain controller to SBS 2008

    - by Quango
    Have an SBS 2008 server in one location, and want to add a backup domain controller at a different site. The two sites are linked by a VPN. New server is running Server 2008 R2, fully patched. At present it is a member server and the DNS is pointing at the SBS DNS. When I try running DCPROMO to connect the server, the wizard runs fine up to the point where the wizard is 'configuring Active Directory Domain Services' and 'examining forest': "The operation failed because: The wizard could not read operational attributes from the remote Active Directory Domain Controller SERVER.DOMAIN.LOCAL using LDAP. "The specified server cannot perform the requested operation." This error can occur if you have not been granted necessary permissions to read data in the directory. For more information, please see article 936241 in the Microsoft Knowledge Base (http://go.microsoft.com/fwlink/?LinkId=88420)." I was logged on as domain administrator. Interestingly the link is invalid and the KB article does not exist..! Settings: Configure this server as an additional Active Directory domain controller for the domain "[domain]". Site: [site] Additional Options: Read-only domain controller: "No" Global catalog: Yes DNS Server: Yes Update DNS Delegation: No Source domain controller: any writable domain controller Database folder: C:\Windows\NTDS Log file folder: C:\Windows\NTDS SYSVOL folder: C:\Windows\SYSVOL The DNS Server service will be configured on this computer. This computer will be configured to use this DNS server as its preferred DNS server.

    Read the article

  • PHP Zend Debugger configuration

    - by newbie123
    Hi i am new to php, I currently learning php using eclipse. I know i have to install the zend debugger my php.ini store at c:windows i had added in these line: [Zend] zend_extension=c:/php/ext/ZendDebugger.dll zend_debugger.allow_hosts=127.0.0.1 zend_debugger.expose_remotely=always zend_debugger.connector_port=10013 but on command prompt i tried php -m it shown that i never install zend debugger. I not sure where goes wrong I check phpinfo also never show any zend information.

    Read the article

  • Profiler for Zend Server CE

    - by Tim Lytle
    I'm looking for a PHP profiler that works with Zend Server (CE). From what I can tell, XDebug is a pain to setup with Zend Server. While Zend Debugger is free (as I understand it), the Profiler is only on Zend Studio. Any other options?

    Read the article

  • why do you like zend-framework?

    - by user1400
    hello all i stared to learn zf for some month , i like to know why other programmer have chocen zend-framework and why do you like zend-framework? What reasons made you choose Zend-framework? has zend-framework Satisfied you? thanks

    Read the article

  • Problem setting up Zend Framework to run with Netbeans

    - by Starx
    I am trying to get Zend Framework working with netbeans, but every time there is the error "php.exe"' is not recognized as an internal or external command, operable program or batch file. I am using WAMP server 2.0 it is installed in e:\wamp My Zend framework is inside e:\wamp\www\ZendFramework-1.10.5 I have located the ZendFramework script as: E:\wamp\www\ZendFramework-1.10.5\bin\zf.bat I am also registered the module. What am i doing wrong? I am running on Windows 7 32 bit, using NETbean 6.9 RC1

    Read the article

  • Problem setting up Zend Framework to run with Netbeans

    - by Starx
    I am trying to get Zend Framework working with netbeans, but every time there is the error "php.exe"' is not recognized as an internal or external command, operable program or batch file. I am using WAMP server 2.0 it is installed in e:\wamp My Zend framework is inside e:\wamp\www\ZendFramework-1.10.5 I have located the ZendFramework script as: E:\wamp\www\ZendFramework-1.10.5\bin\zf.bat I am also registered the module. What am i doing wrong? I am running on Windows 7 32 bit, using NETbean 6.9 RC1

    Read the article

  • "Zend Optimizer not installed" after I updated to Ubuntu 10.04

    - by Eugene
    Hi guys, I've just updated from 9.10 to 10.04. Everything seems to run fine except for zend optimizer which is throwing "Zend Optimizer not installed" error. I went to php.ini and the following line is still there Code: zend_extension=/etc/php5/ZendOptimizer.so Also I checked that the file does exist and that the php.ini I am looking at is in fact the php.ini file that is being used by the server. Please let me know if you have any ideas about how to fix or debug this. Thanks, Eugene

    Read the article

  • How to use Zend Studion for Java development

    - by Itay Moav
    I have the Zend studio which a PHP editor based on Eclipse. I want to use it now to develop some Java. I think Zend has disabled all the Java centric project/views/perspectives that come with Eclipse (or may be not included the right plugins?) What steps should I take to use it, instead of having two eclipses open at the same time.

    Read the article

  • phpmyadmin configuration on zend server community edition

    - by kamal
    hi i am new to zend and i installed zend server in my local machine, i found phpmyadmin on my instalation directory and i copied it on htdocs. while running http://localhost/phpmyadmin it appears login page and when i enter username and password it does not redirects to the main page. instead it gives "internal server error" thanks in advance

    Read the article

  • Zend_Feed_Reader Not supported Schema

    - by LookUp Webmaster
    Hello, I'm using Zend FW and wanted to make a feed reader. I did the following: $feed = Zend_Feed_Reader::import('feed://blog.lookup.cl/?feed=rss2'); $data = array( 'title' => $feed->getTitle(), 'link' => $feed->getLink(), 'dateModified' => $feed->getDateModified(), 'description' => $feed->getDescription(), 'language' => $feed->getLanguage(), 'entries' => array(), ); foreach ($feed as $entry) { $edata = array( 'title' => $entry->getTitle(), 'description' => $entry->getDescription(), 'dateModified' => $entry->getDateModified(), 'authors' => $entry->getAuthors(), 'link' => $entry->getLink(), 'content' => $entry->getContent() ); $data['entries'][] = $edata; } And it throws the following exception: Scheme "feed" is not supported The blog was made using Wordpress. What's wrong? If "feed it's not supported", how can I change the type of feed that Wordpress does? Thanks in advance, Take care,

    Read the article

  • Multiple/nested "select where" with Zend_Db_Select

    - by DJRayon
    Hi there I need to create something like this: select name from table where active = 1 AND (name LIKE 'bla' OR description LIKE 'bla') The first part is easy: $sqlcmd = $db->select() ->from("table", "name") ->where("active = ?", 1) Now comes the tricky part. How can I nest? I know that I can just write ->orWhere("name LIKE ? OR description LIKE ?", "bla") But thats wron, because I need to dynamically change all the parts. The query will be built all the time the script runs. Some parts get deleted, some altered. In this example I need to add those OR-s because sometimes I need to search wider. "My Zend Logic" tells me that the correct way is like this: $sqlcmd = $db->select() ->from("table", "name") ->where("active = ?", 1) ->where(array( $db->select->where("name LIKE ?", "bla"), $db->select->orWhere("description LIKE ?", "bla") )) But that doesn't work (atleast I dont remember it working). Please. Can someone help me to find a object oriented way for nesting "where"-s

    Read the article

  • Zend_Test: No default module defined for this application

    - by jiewmeng
    UPDATE 23 Dec I had the problem where Zend Framework complains about "No default module defined for this application". I didn't use Modules and the main app works fine. I finally solved the problem with the help from weierophinney.net Your bootstrap needs to minimally set the controller directory -- do a call to $this->frontController->addControllerDirectory(...) in your appBootstrap() method. I didn't in my example, as my Initialization plugin does that sort of thing for me. The problem is solved by adding the below to setUp() $this->getFrontController()->setControllerDirectory(APPLICATION_PATH . '/controllers'); But now, I have afew other questions: 1. Why does that value not get initialized by application.ini? In application.ini, I have [production] resources.frontController.controllerDirectory = APPLICATION_PATH "/controllers" [testing : production] // didn't change anything regarding modules nor controllers 2. I tried setting the controllerDirectory in bootstrap.php of my unit test, but it does not work $front = Zend_Controller_Front::getInstance(); $front->setControllerDirectory(APPLICATION_PATH . '/controllers'); The only way that works is using setUp(). Why is that? END UPDATE 23 Dec I am getting the above error when unit testing my controller plugins. I am not using any modules. in my bootstrap.php for unit testing, I even tried adding $front = Zend_Controller_Front::getInstance(); $front->setDefaultModule('default'); But it still does not work. Anyways my bootstrap.php looks like this UPDATE: the error looks something like There were 2 errors: 1) Application_Controller_Plugin_AclTest::testAccessToUnauthorizedPageRedirectsToLogin Zend_Controller_Exception: No default module defined for this application D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Dispatcher\Standard.php:391 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Dispatcher\Standard.php:204 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Dispatcher\Standard.php:244 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Front.php:954 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Test\PHPUnit\ControllerTestCase.php:205 D:\Projects\Tickle\tests\application\controllers\plugins\aclTest.php:6 2) Application_Controller_Plugin_AclTest::testAccessToAllowedPageWorks Zend_Controller_Exception: No default module defined for this application D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Dispatcher\Standard.php:391 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Dispatcher\Standard.php:204 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Dispatcher\Standard.php:244 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Controller\Front.php:954 D:\ResourceLibrary\Frameworks\PHPFrameworks\Zend\Test\PHPUnit\ControllerTestCase.php:205 D:\Projects\Tickle\tests\application\controllers\plugins\aclTest.php:16 UPDATE I tried adding public function setUp() { $front = Zend_Controller_Front::getInstance(); $front->setDefaultModule('default'); } then 1 part works. public function testAccessToUnauthorizedPageRedirectsToLogin() { // this fails with exception "Zend_Controller_Exception: No default module defined for this application" $this->dispatch('/projects'); $this->assertController('auth'); $this->assertAction('login'); } public function testAccessToAllowedPageWorks() { // this passes $auth = Zend_Auth::getInstance(); $authAdapter = new Application_Auth_Adapter('jiewmeng', 'password'); $auth->authenticate($authAdapter); $this->dispatch('/projects'); $this->assertController('projects'); $this->assertAction('index'); }

    Read the article

  • Primary domain controller has crashed, secondary does not log in

    - by Hosm
    Hi everybody, I had a primary domain controller on machine A and a secondary one on machine B in my AD domain. Due to some hardware/software problems, I decided to migrate the role of primary domain controller to machine B. Unfortunately, machine A has totally crashed and does not boot. Now I can not even log in to machine B (which itself was a controller in the domain). I need to log into machine B then choose it as the primary controller. I already have synced DNS and AD info. when machine A was alive. Anyone can provide an idea?

    Read the article

  • Cannot ping my domain-joined server - Can only ping domain controller - host unreachable

    - by Vazgen
    I have a HyperV Server hosting a Domain Controller VM (192.168.1.50) and another VM (192.168.1.51) joined to this domain. I have: domain controller as DNS server forward lookup zone for the domain with host record for 192.168.1.50 and 192.168.1.51 Windows client has primary DNS server set to 192.168.1.50 and secondary to my ISP I can ping 192.168.1.50 (domain controller) successfully but cannot ping 192.168.1.51 (domain-joined VM) When pinging from Windows client: ping 192.168.1.51 Reply from 192.168.1.129 : Destination host unreachable When pinging from Domain Controller: ping 192.168.1.51 Reply from 192.168.1.50 : Destination host unreachable I have 2 virtual network adapters one PRIVATE for intranet (set to static IP 192.168.1.51) and one PUBLIC for internet with a dynamic IP. I noticed the the PUBLIC one inherited the "mydomain.com" domain subtitle after joining the domain... I don't know what this meant but it seemed more intuitive to me to switch THIS ONE to have the static IP. After I configured that I still could not ping but now I get: ping 192.168.1.51 Request timed out What seems to be the issue, I'm relatively new to networking.

    Read the article

  • Using Xbox 360 controller with Mac OS X (specifically turning it off)

    - by Bob King
    So I've been using this driver for a few months with the Xbox 360 Wireless Controller For Windows with my Mac Mini. Here's an article about the driver on Gizmodo. The driver works really well for actually using the controller, but there doesn't seem to be a way to power off the controller without pulling the batteries. Does anyone know of a replacement driver that includes power-off capabilities, or know of some other undocumented way to turn the controller off? Note: I've been having problems getting to the site, but it could be our corporate filtering.

    Read the article

  • PC does not recognize XBox 360 controller connected through Play & Charge Kit

    - by Mike Cole
    I wanted to hook up my wireless XBox 360 controller to my PC running windows 7. I'm trying to use the Play & Charge kit since I already had that laying around. I plugged it in and Windows recognize it and installed it. It registers in Device Manager as "Xbox 360 Wireless Controller via Play & Charge Kit". The controller also has the 1st quadrant lit. However, I can't seem to make this work with any games. I installed the "Microsoft Xbox 360 Accessories" kit from MS website, and I run the Accessories Status app and it doesn't recognize that the controller is connected. Does anybody know what I'm doing wrong out there?

    Read the article

  • Virtual host in Apache Zend

    - by llocani
    I'd like to ask you if you can tell me why I can't get Vhost in Apache to work my Vhostconf is: NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] DocumentRoot "E:/Archivos de programa/Zend/Apache2/htdocs" ServerName localhost <Directory "E:/Archivos de programa/Zend/Apache2/htdocs"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> #AllowOveride all </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands" ServerName healinghands.loc <Directory "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ErrorLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands/logs/error.log" CustomLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/HealingHands/logs/access.log" common #AllowOveride all </VirtualHost> <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects" ServerName dev.loc <Directory "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects"> Options FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> ErrorLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/logs/error.log" CustomLog "E:/Documents and Settings/dvieira/Mis documentos/NetBeansProjects/logs/access.log" common #AllowOveride all </VirtualHost> My httpd.conf is: ServerRoot "E:\Archivos de programa\Zend\Apache2" Listen 80 LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule cgi_module modules/mod_cgi.so LoadModule dir_module modules/mod_dir.so LoadModule env_module modules/mod_env.so LoadModule filter_module modules/mod_filter.so LoadModule headers_module modules/mod_headers.so LoadModule imagemap_module modules/mod_imagemap.so LoadModule include_module modules/mod_include.so LoadModule info_module modules/mod_info.so LoadModule isapi_module modules/mod_isapi.so LoadModule log_config_module modules/mod_log_config.so LoadModule mime_module modules/mod_mime.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule ssl_module modules/mod_ssl.so LoadModule status_module modules/mod_status.so LoadModule userdir_module modules/mod_userdir.so <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> ServerAdmin [email protected] DocumentRoot "E:\Archivos de programa\Zend\Apache2/htdocs" <Directory /> Options FollowSymLinks AllowOverride all Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.php index.html home.php </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "logs/access.log" common </IfModule> <IfModule alias_module> Alias /NetBeansProjects "E:\Documents and Settings\dvieira\Mis documentos\NetBeansProjects" ScriptAlias /cgi-bin/ "E:\Archivos de programa\Zend\Apache2/cgi-bin/" </IfModule> <IfModule cgid_module> </IfModule> <Directory "E:\Archivos de programa\Zend\Apache2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz </IfModule> Include conf/extra/httpd-vhosts.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> Include "conf/zend.conf" NameVirtualHost *:80 <VirtualHost *:80> Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/zend-default-vhost-80.conf" </VirtualHost> Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/globals-*.conf" Include "E:\Archivos de programa\Zend\ZendServer/etc/sites.d/vhost_*.conf" And my host in Windows: 127.0.0.1 localhost 127.0.0.1 healinghands.loc 127.0.0.1 dev.loc And I can't get any of the browser to recognize dev.loc or healinghands.loc but a ping does it. Localhost is working fine. I've spent 3 days now traying to solve this for my one but I finally quit and have to ask. The error should be this Error Code 11002: host not found. Background: this error indicates that the gateway could not find an authoritative DNS server for the website you are trying to access. Date: 5/20/2013 5:51:03 PM Server: Source: DNS problem. i'd like to add this ping Haciendo ping a healinghands.loc [127.0.0.1] con 32 bytes de datos: Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Respuesta desde 127.0.0.1: bytes=32 tiempo<1m TTL=128 Estadísticas de ping para 127.0.0.1: Paquetes: enviados = 4, recibidos = 4, perdidos = 0 (0% perdidos), Tiempos aproximados de ida y vuelta en milisegundos: Mínimo = 0ms, Máximo = 0ms, Media = 0ms Today i've tryed something: i've add this domains into the exceptions of mi ie proxy config. This worked for healinghands.loc but not for dev.loc i really do not understand why, both config are exactly the same except for de documentroot. I will continue searching

    Read the article

  • How do I install BCM4312 wireless drivers?

    - by t3ch
    completely new to Ubuntu. How do I add Wireless driver for my laptop? I am running a Dell XPS M1330. Right now its acts as if I dont have a Wi-Fi card. :~$ lspci 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c) 00:01.0 PCI bridge: Intel Corporation Mobile PM965/GM965/GL960 PCI Express Root Port (rev 0c) 00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02) 00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02) 00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: nVidia Corporation G86 [GeForce 8400M GS] (rev a1) 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) 03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12) 09:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5906M Fast Ethernet PCI Express (rev 02) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)

    Read the article

  • cannot boot ubuntu 13.10 with my usb, Can i change the kernal on my laptop to run it?

    - by Carlos Dunick
    Currently i am running 12.04 and looking for an upgrade to 13.10 I first tried a bootable 64bit usb and failed. With the message saying "Kernal requires an x86-64 CPU but only detected an I686 CPU Unable to boot please use a kernal appropriate for your CPU" then tried 32bit and same message came up. Is this due to my laptop simply being to slow? or can/should i change the kernal somehow? Acer Aspire 5710z Intel Pentium dual core processor, 1.73Ghz, 533 MHz FSB, 1 MB L2 cache. 2GB DDR2 lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) 00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02) 04:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02) 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 06:00.0 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller 06:00.1 SD Host controller: ENE Technology Inc ENE PCI SmartMedia / xD Card Reader Controller 06:00.2 FLASH memory: ENE Technology Inc Memory Stick Card Reader Controller 06:00.3 FLASH memory: ENE Technology Inc ENE PCI Secure Digital / MMC Card Reader Controller

    Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >