Search Results

Search found 3844 results on 154 pages for 'firewall bypass'.

Page 100/154 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• new ubuntu server installation - java server not receiving packets

  - by James

  I have developed a Java server which listens for UDP packets which come from mobile devices. At the moment, it works correctly if I run my Server on my windows PC. I can receive and respond to the UDP packets sent from my phone (over 3g, not wifi). However, I am trying to run the Server on a different computer which I found lying around my house. I have basically done a clean install of Ubuntu Server edition, updated it, installed the java run time environment and configured port forwarding to allow connections on the appropriate port. I have also tried to disable the firewall. The problem is, it doesn't appear as if the server is receiving any packets and I've exhausted my brain thinking on how to solve/debug the problem. Can anyone suggest to me what the problem might be? or more likely something I can do to help me find out more information about what is going wrong.

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• Simple NAT router for ESX

  - by Evan M.

  Hi Guys, I'm looking for a simple virtual appliance that I can deploy to my ESX environment to use as a virtual NAT router / firewall to create an isolated network that I can easily give internet access too. Basic setup: ESX Host, has 2 vswitches configured: 1 is connected to the physical LAN, the other is isolated. I need an appliance that I can add 2 vNICs to, and attach one to the isolated vSwitch, the other to the LAN, to give the isolated network outbound access (so it can reach the internet). Anyone have an appliance that I can setup quickly to do so? Thanks.

  Read the article

• Timeouts when connecting to SQL Server since installing SP1 for Windows 7

  - by Julien

  Hi, I just installed SP1 for windows 7 and I have severe performance degradation when connecting to SQL Server 2005 since then. Establishing connection takes more than 30 seconds while it's instantaneous on another computer. Firewall is disabled and I didn't make any change to the configuration. It happens both when trying to connect with a hostname and with an ip address. Everything else seems to be fine (for instance, I'm have no issue connecting to other computers with remote desktop) What can cause such a problem? Thanks in advance! Edit : uninstalling the SP1 solves the issue instantly.

  Read the article

• What's required to enable communication between two IP ranges located behind one switch?

  - by Eric3

  Within our co-located networking closet, we have control over two ranges of 254 addresses, e.g. 64.123.45.0/24 and 65.234.56.0/24. The problem is, if a host has only one IP address, or a block of addresses in only one range, it can't contact any of the addresses in the other subnet. All of our hosts use our hosting provider's respective gateway, e.g. 64.123.45.1 or 65.234.56.1 A host on the 64.123.45.0/24 range can contact the 65.234.56.1 gateway and vice-versa Everything in our closet is connected to an HP ProCurve 2810 (a Layer 2-only switch), which connects through a Juniper NetScreen-25 firewall to the outside world What can I do to enable communication between the two ranges? Is there some settings I can change, or do I need better networking equipment?

  Read the article

• Accessing the Internet via browser

  - by ucas

  I am on Windows 7 and using Firefox browser. I am using WiFi, but since the morning I cannot access the Internet via the browsers (Firefox, Chrome, or IE). The laptop shows there is Internet connection, Skype is online, but I can't reach the Internet. Then I launched Tor application which creates secure channel and provides its Firefox browser. Well, I can now access the Internet over that browser. So, what might be the problem causing this malfunction? The error: The connection has timed out The server at mail.google.com is taking too long to respond. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Best regards

  Read the article

• Modern open source NIDS/HIDS and consoles?

  - by MattC

  Years back we set up an IDS solution by placing a tap in front of our exterior firewall, piping all the traffic on our DS1 through an IDS box and then sending the results off to a logging server running ACiD. This was around 2005-ish. I've been asked to revamp the solution and expand on it and looking around, I see that the last release of ACiD was from 2003 and I can't seem to find anything else that seems even remotely up-to-date. While these things may be feature complete, I worry about library conflicts, etc. Can anyone give me suggestions for a Linux/OpenBSD based solution using somewhat modern tools? Just to be clear, I know that Snort is still actively developed. I guess I'm more in the market for a modern open-source web console to consolidate the data. Of course if people have great experiences with IDS' other than Snort I'm happy to hear about it.

  Read the article

• SQL server periodically gets disconnected

  - by Maulin

  Hi, Our environment is: Windows Server 2003, Service Pack 2 SQL Server Express 2005 SQLServer JDBC driver 1.2 (also tried Jtds) Sun JDK 1.6 (we tried this on JDK 1.5 as well) There is no virus protection software on the host, and no firewall is enabled. We have Web application deployed in JBOSS 4.0.2. Our problem is that the JDBC connection to SQL server periodically gets disconnected, and then we can't reconnect to the SQL server at all, unless we physically restart the server on which JBOSS deployed. we are getting following error in log. Software caused connect on abort: recv failed Note: We are able to connect to SQL server using sample java test class. Any suggestions would be most appreciated, as this is a serious, mission-criticial problem for us right now.

  Read the article

• Setup IIS 7 as FTP Server that is connectable outside of my local network

  - by Usta

  I was able to setup an FTP site that I was able to access via ftp://127.0.0.1/ or my local(static) ip. To do this I followed these instructions (with the exception that I did not bind to 127.0.0.1 as suggested) http://learn.iis.net/page.aspx/301/creating-a-new-ftp-site-in-iis-7/ I have created a firewall exception for port 20 and 21, and setup port-forwarding on my wireless router. But I can only access the site via local-host, and I need to have a friend have read access to it. So how do I enable remote access to it? (I'd rather not purchase a domain-name) My setup: IIS 7.5 Windows 7 Professional Wireless Network Norton Internet Security 2012 An Internal Static IP Address

  Read the article

• Cisco 1841 Box and Watchguard XTM21-W

  - by Corey

  I have never set one of these up before and need a little assistance. Right now we have a T1 line coming in from Sprint to a Cisco 1841 and then on to our router. However, when I plug the Cisco 1841 into Port 0 and the router into Port 3 it does not work. In Port 1 I have my management computer plugged in. We have one subnet and this must be easy but I cannot figure out how to make this work. When the firewall is plugged in then I get no internet or network access.

  Read the article

• Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

  - by gil b.

  Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

  Read the article

• Open ports for Apache Tomcat-7.0.32 on Linux Mandriva

  - by ivanov-void

  I installed Apache Tomcat-7.0.32 on Linux Mandriva and I want to make it accessible. for this I need to open ports in iptables. I added the following rules- iptables -A INPUT -p tcp -m tcp --dport 8081 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8010 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8444 --syn -j ACCEPT iptables -A INPUT -p tcp -m tcp --dport 8006 --syn -j ACCEPT then save and restart iptables - /etc/init.d/iptables save /etc/init.d/iptables restart verify, that ports is open - netstat -tulpn | less I am running command - netstat-ntpl | grep java and see - When I disable the firewall, I see the start page of the server on request - http://server_ip:8081/ When enable - server not accessible from outside. In what may be the cause? I would be most grateful for the information! Thank you!

  Read the article

• How to tunnel port 25565 through SSH?

  - by user62389

  I want to play a game which is hosted on port 25565 (minecraft!), but my university firewall does not allow this port. I have a dedicated server running linux not too far from uni, so I think there's a way to tunnel through it (but I've never done this before and have no knowledge/experience of tunnelling) It would probably be slow, but it's better than not being able to play at all. Is it possible to do using only SSH, or do I need other client/server software? My server has OpenSSH installed. Also, the computer I'm using to play the game is running Ubuntu. I've tried searching but there seem to be so many different solutions to different types of problem =/

  Read the article

• iptables: built-in INPUT chain in nat table?

  - by ughmandaem

  I have a Gentoo Linux system running linux 2.6.38-rc8. I also have a machine running Ubuntu with linux 2.6.35-27. I also have a virtual machine running Debian Unstable with linux 2.6.37-2. On the Gentoo and Debian systems I have an INPUT chain built into my nat table in addition to PREROUTING, OUTPUT, and POSTROUTING. On Ubuntu, I only have PREROUTING, OUTPUT, and POSTROUTING. I am able to use this INPUT chain to use SNAT to modify the source of a packet that is destined to the local machine (imagine simulating an incoming spoofed IP to a local application or just to test a virtual host configuration). This is possible with 2 firewall rules on Gentoo and Debian but seemingly not so on Ubuntu. I looked around for documentation on changes to the SNAT target and the INPUT chain of the nat table and I couldn't find anything. Does anyone know if this is a configuration issue or is it something that was just added in more recent versions of linux?

  Read the article

• Email error 'Default email client is not properly installed' after installing Bugzilla 3.6.3 on Windows Home Server 2011

  - by Brian Frost

  I have been using Bugzilla fine on the older 32-bit Windows Home Server and I have now started a migration to the newer Windows Home Server 2011 with a new machine and a fresh Bugzilla install of 3.6.3. All goes well until I try to check out the email action and I get 'Could not perform this operation because the defaulty mail client in not properly installed. Is this a security /firewall issue? I dont know enough about servers to know what to look for, so any help will be gratefully appreciated. Thanks.

  Read the article

• Airport Express configuration

  - by Christina

  We are trying to set up remote access to a computer that houses a server fro a particular program we are running. The program says we need to configure the office router. In the firewall settings it says to open ports 5345-5351 (TCP only). Port Forwarding: You will also need to forward the same range of ports (5345-5351) to the computer running the Server. This typically requires that the computer running the Server be assigned a static IP on the local network. Having trouble figuring out which IP address we actually need to be using on the client side of this program in order to access the server computer. Can someone walk through this process?? We are working on Mac OSX 10.5. Thank you in advance!

  Read the article

• httpd service keep restarting. after 15-20 mins

  - by niraj

  I have recently purchased Dedicated Server which has 16bg ram and 1TB Harddisk. It has Cpanel and for firewall CSF Installd. I am mainly going to install it for File hosting service. Now the day i moved my httpd service keep restarting every 15-20 mins. It becomes unresponsive after that so have to manually restart it. My httpd settings are Start Servers = 5 Minimum Spare Servers = 5 Maximum Spare Servers = 10 Server Limit = 20000 Max Clients = 10000 Max Requests Per Child = 10000 Keep-Alive = On Keep-Alive Timeout = 5 Max Keep-Alive Requests = Unlimited Timeout 300 TOP is top - 14:53:41 up 1 day, 23:39, 2 users, load average: 0.10, 0.14, 0.09 Tasks: 1563 total, 1 running, 1562 sleeping, 0 stopped, 0 zombie Cpu(s): 0.7%us, 0.6%sy, 0.0%ni, 98.1%id, 0.2%wa, 0.0%hi, 0.5%si, 0.0%st Mem: 16303780k total, 16142048k used, 161732k free, 135264k buffers Swap: 8224760k total, 868k used, 8223892k free, 14136616k cached Please help me in this its keep happning.

  Read the article

• AXFR problem using gradwell secondary DNS

  - by Roaders

  Hi All I use Gradwell.com to provide secondary DNS but I keep getting e-mails along the lines of the following saying that it's not working: You have asked us to provide a secondary DNS service for the following domain(s) Unfortunately, the primary DNS server(s) you specified are not permitting the necessary zone transfers from our servers, or they are not answering "SOA" queries for your domain correctly. I have gone through the support procedure and they weren't that helpful. They have suggested the following: Our secondline team have suggested setting the AXFR to use anouther machine. This will ensure that the transfer is not locked down to one machine and should allow any machine to make the request I don't really know what AFXR is and I only have 1 production machine so I can't set the AFXR to use another one! In previous support correspondence we confirmed that I am allowing transfers to the correct IP and that I have the correct ports open on the firewall. I am running Windows Server 2003. What can I do to try and get these zone transfers working? Thanks

  Read the article

• DSL-504T as dumb ADSL modem

  - by petebob796

  I am trying to setup an existing DSL-504T ADSL router to work as a dumb modem for a DIR-825 wifi router. I am assuming I should try and move as much of the control to the DIR-825 as possible. It's a PPPoA connection so I don't think I can use bridge mode. Does anyone have any guidance on this? Should I have 2 subnets? Should I set the DIR-825 as the DMZ on the DSL-504T? Do I need to keep NAT and firewall enabled on DSL-504T? Basically I have it working but want to know if I have set it up correctly as I really want the QoS to work on the DIR-825.

  Read the article

• Proxying fake domain to a localhost port

  - by Trevor Burnham

  I'd like to do much the same thing described at Redirect Domain Name to Localhost for web app development purposes, but with the twist that I'd like requests to fakedomain.com:80 to be routed to localhost:8080, say, so that I don't have to actually use my development machine's port 80. I'd welcome answers that take the form of: Small changes to configuration files like /etc/hosts, and/or An easy-to-configure proxy server I could run Note: Pow takes the approach of setting a firewall rule to forward all incoming traffic on port 80 to port 20559. That may be an acceptable solution, but ideally, I'd like to forward only a specific domain + port combination.

  Read the article

• Barring connections if VPN is down.

  - by Majid

  I have a VPN account and use it for sensitive communication. However the VPN connection sometimes is dropped while my main connection to the internet is still alive. The pages I visit through VPN are on HTTP (not secure) and have javascript code which pings the host every minute or so on a timer. So it happens sometimes that the VPN connection is dropped and yet js sends a request to the server (with the cookies). How could I restrict connections so they only happen if the VPN is live? Edit - Some required details were missing OS: Windows XP SP2 Browser (mostly used): Google Chrome Firewall: Windows default Sites to filter: not all traffic but all in a list of sites like abc.com, xyz.com

  Read the article

• vsFTPd and iptables - how to configure them in CentOS 5.5?

  - by Vincenzo

  I've installed vsFTPd in CentOS 5.5, on TWO servers, and added this rule to their iptable-s: -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 21 -j ACCEPT Looks like this is not enough, since when I'm trying to upload a file from one server to another, I'm getting this result (IP address is masked): # ftp 99.99.99.99 Connected to …com (99.99.99.99). 220 (vsFTPd 2.0.5) Name (99.99.99.99:root): vinny 331 Please specify the password. Password: 230 Login successful. Remote system type is UNIX. Using binary mode to transfer files. ftp> ls 227 Entering Passive Mode (99,99,99,99,107,74) ftp: connect: No route to host I've found a few articles in the net about the second rule I have to add to iptables, but I didn't find the right syntax for it. Could you please help?

  Read the article

• Apache does not serve non-locally

  - by yodaj007

  I have a freshly installed instance of Fedora Core 16 inside VirtualBox using bridged networking. On it, as root I typed in: yum -y install httpd service httpd start ifconfig Inside the VM, I can open a web browser to 'localhost' and I get the Apache test page. It works. But in Windows (the machine hosting the VM), I point my browser to the IP address returned by ifconfig (192.168.2.122). The connection times out. I can go to a command prompt and ping the VM. Is there a firewall or something that comes with Fedora by default? Or is there something I need to change in a config file?

  Read the article

• How must I deal with anti-virus software on Windows 7

  - by Heather

  I know this question is looking like an easy question or not a question at all but it's not really easy question. I'm not related to security and anti-viruses and just don't trust every provided anti-virus. So first question is a real question - Is it OK (safe) to not use anti-virus at all. I know how to use firewall, usually I use only trusted connections and surfing trusted sites. My chances to get virus is really low. Even I've got a bit outdated PC and don't want to pay the performance for it. I can do monthly scans without having one installed - is it OK to be safe ? If not can you recommend a good free antivirus solution?

  Read the article

• Missing access log for virtual host on Plesk

  - by Cummander Checkov

  For some reason i don't understand, after creating a new virtual host / domain in Plesk a few months back, i cannot seem to find the access log. I noticed this when running /usr/local/psa/admin/sbin/statistics The host in question is being scanned Main HTML page is 'awstats.<hostname_masked>-http.html'. Create/Update database for config "/opt/psa/etc/awstats/awstats.<hostname_masked>.com-https.conf" by AWStats version 6.95 (build 1.943) From data in log file "-"... Phase 1 : First bypass old records, searching new record... Searching new records from beginning of log file... Jumped lines in file: 0 Parsed lines in file: 0 Found 0 dropped records, Found 0 corrupted records, Found 0 old records, Found 0 new qualified records. So basically no access logs have been parsed/found. I then went on to check if i could find the log myself. I looked in /var/www/vhosts/<hostname_masked>.com/statistics/logs but all i find is error_log Does anybody know what is wrong here and perhaps how i could fix this? Note: in the <hostname_masked>.com/conf/ folder i keep a custom vhost.conf file, which however contains only some rewrite conditions plus a directory statement that contains php_admin_flag and php_admin_value settings. None of them are related to logging though.

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >