Search Results

Search found 31973 results on 1279 pages for 'network library'.

Page 100/1279 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• Printing on Windows 8 with PDF viewer (Adobe Reader) from network

  - by Bongo

  i have a problem with the Adobe Reader 8, but the problem seems to be equally bad with other pdf viewers. Here is the configuration: My PDF viewer is located on network drive "Z:" which is the network adress \dgs-main\progs. I tried to start the adobe reader from here - \\dgs-main\progs\Adobe\Reader 8.0\Reader\AcroRd32.exe and open the PDF from here - C:\Users\ServiceDesk\AppData\Local\Temp\GeneratedPDF.pdf The problem is as follows, if i open the PDF with a local PDF viewer everything works fine and i can print the document. If i open the PDF with the Network PDF viewer then it opens, but printing is impossible. The error message states: "Unable to start print job. Is printer available?" As mentioned above, it works with a local pdf viewer. In both cases i use the same printer. The Printer is a network printer but even with a local printer it fails. The error occurs only on Windows 8 machines. On windows 7 it works fine. I Hope somebody can tell me what the problem is. Thanks in advance and have a fine day.

  Read the article

• Setting up a Network Bridge on Linux VM (Windows 7 Host)

  - by GrandAdmiral

  I would like to use NetEm to simulate a low bandwidth environment while testing an Internet-connected device. My plan is to setup a bridge in a Linux VM (Linux Mint 13) on a Windows 7 host. Unfortunately I'm having trouble setting up the bridge. Then I can use NetEm in the Linux VM to limit the bandwidth to an external device. I went with the following script: ifconfig eth0 0.0.0.0 promisc up ifconfig eth1 0.0.0.0 promisc up Then create the bridge and bring it up: brctl addbr br0 brctl setfd br0 0 brctl addif br0 eth0 brctl addif br0 eth1 dhclient br0 ifconfig br0 up When I run that script, I see the following warning: Rather than invoking init scripts through /etc/init.d, use the service(8) utility, e.g. service smbd reload Since the script you are attempting to invoke has been converted to an Upstart job, you may also use the reload(8) utility, e.g. reload smbd The device connecting to the bridge is able to obtain an IP Address, but it can only ping the IP Address of the bridge (both are 10.2.32.xx). Then after a few minutes, other parts of our network go down. I'm not sure why, but once I kill the bridge the network is fine. Is it possible to setup a network bridge in a Linux VM? Do I need to do something else with the dhclient br0 part of the script? By the way, I'm using VirtualBox. The wired connection is eth0 and the wireless connection is eth1. The wired connection is connecting to the device and the wireless connection is going to the network. Both adapters are set up as bridged adapters with promiscuous mode set to "allow all".

  Read the article

• Translating debian network configuration to gentoo

  - by thpetrus

  I just got rid off Debian on my VPS (OpenVZ) and installed Gentoo on it, however it is a plain Gentoo image without further configuration, i.e. no working network. I'm not familiar with Debian and coulnd't figure out how to get the network set up, these are the debian network files /etc/network/interfaces: auto venet0 iface venet0 inet manual up ifconfig venet0 up up ifconfig venet0 127.0.0.2 up route add default dev venet0 down route del default dev venet0 down ifconfig venet0 down iface venet0 inet6 manual up ifconfig venet0 add ipv6addr/128 down ifconfig venet0 del ipv6addr/128 up route -A inet6 add default dev venet0 down route -A inet6 del default dev venet0 auto venet0:0 iface venet0:0 inet static address external_ip netmask 255.255.255.255 auto venet0:1 iface venet0:1 inet static address internal_ip netmask 255.255.255.255 Please note that external_ip, internal_ip and ipv6addr are placeholders. I copied the /etc/resolv.conf, know the gateway_ip and also have another ouput of ifconfig, if necessary. This is what I came up with, /etc/conf.d/net: config_venet0="127.0.0.2 netmask 255.255.255.255 brd 0.0.0.0" config_venet0:0="external_ip netmask 255.255.255.255 brd 0.0.0.0" route_venet0:0="default via gateway_ip" config_venet0:1="internal_ip netmask 255.255.255.255 brd 0.0.0.0" Broadcast IP is taken from ifconfig debian output - however it doesn't work. A symbolic link net.venet0:0 -> net.lo in /etc/init.d/ was created and I added net.venet0:0 to the boot runlevel.

  Read the article

• Network card/driver stops under heavy load

  - by Uwe Keim

  Since about approx. 2 month, I do have the following issue with my approx. 1 year old development machine (Windows 7, 64 bit): When doing network intensive operations, like e.g. executing some SQL script on a remote SQL server to select or update 1000 of records, the network card stops working. I.e. suddenly, No network connection is present anymore. No internet, no local connection, simply nothing. The only resolution so far I found is to disable my network card and then simply enable it back, like in the following screenshots: 1.) Click "Deactivate" 2.) Click "Activate" (German screenshots only, sorry) Now this is an acceptable solution to work around this issue, but I would love to have this fixed, since it suddenly stops me from working when I'm connected remotely via VPN/RDP on my machine (Win7 64bit). So my question is: Could you imagine a possible cause for this issue and give some hints how to hunt/resolve it? I could imagine that this is a driver issue, a hardware issue or even some kind of background software issue like a software firewall or a virus scanner.

  Read the article

• Backing up large network (~200 clients) -- Enough Bandwidth?

  - by mtkoan

  My company wants to institute a backup plan for all of the clients on our network, which is about 200. We back up our servers and SQL databases regularly, but its been our policy to not backup individuals. What is most critical for people is their Documents and PST files in Outlook. PST files can be very large, and most people's are ~1-1.5 GB around here. So with PST files alone that is 200-300 GB of data needing to be transferred daily to a sever for backup. Or compressing first, then transferring, but many of the machines are VERY old and such a task would grind their computer to a halt. Isn't this the reason networks use things like VMware -- to reduce network traffic and streamline backups? Or is this only to reduce hardware costs? Would this much network traffic everyday drastically slow down our network? Enough to the point we'd have to mandate it to be done at night only? Or could we stagger then through out the day? Really appreciate any input, thank you.

  Read the article

• Amazon EC2 instance missing Network Interface

  - by Sergiks

  I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

  Read the article

• Isolate clients on same subnet?

  - by stefan.at.wpf

  Given n (e.g. 200) clients in a /24 subnet and the following network structure: client 1 \ . \ . switch -- firewall . / client n / (in words: all clients connected to one switch and the switch connected to the firewall) Now by default, e.g. client 1 and client n can communicate directly using the switch, without any packets ever arriving the firewall. Therefore none of those packets could be filtered. However I would like to filter the packets between the clients, therefore I want to disallow any direct communication between the clients. I know this is possible using vlans, but then - according to my understanding - I would have to put all clients in their own network. However I don't even have that much IP addresses: I have about 200 clients, only a /24 subnet and all clients shall have public ip addresses, therefore I can't just create a private network for each of them (well, maybe using some NAT, but I'd like to avoid that). So, is there any way to tell the switch: Forward all packets to the firewall, don't allow direct communication between clients? Thanks for any hint!

  Read the article

• OpenVZ with bridged interfaces and VLAN

  - by Deimosfr

  Hi, I've got a problem with OpenVZ with bridged VLAN. Here is my configuration: +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN work on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110: inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seems to be working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian Lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks OK, but when I start my VE, here is the message: ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please? Thanks

  Read the article

• Enabled Network Discovery on Server, and now VNC and Squeezebox clients don't work

  - by Mike Hanson

  I've recently setup a Windows Server 2008. It's running an email server, Squeezebox server, MS SQL Server, etc. I'm doing remote maintenance with UltraVNC. I had everything working fine. Then the server needed to access a network share on another machine, and I was prompted to turn on network discovery, which I did. I chose the Home rather than Public option. Since doing that, some things have stopped working, while others are still fine. Shared folders and the the Email services (ports 25 and 110) are still accessible. VNC (port 5900) and Squeezeboxes (port 9000) no longer work. Here's what I've tried to try to solve the problem: Checked the network discovery settings, to see if anything looked strange. Checked the firewall settings, and those ports appear to be open. Also in the firewall settings, the entries for Private domain Network Discovery were all on, but the Domain/Public ones were off. I tried turning those on. In the services, turned on Function Discovery Resource Publication and SSDP Discovery. Any other suggestions?

  Read the article

• Why the VPN Network Shake-Up?

  - by Brent Arias

  I can RDP to another machine on my home network, only if I'm not also hooked up to my employer's VPN with the Cisco VPN client. Indeed, I can't even ping the other machine by name in this mode, because ICMP suddenly thinks that ( ping myMachine ) now means ( ping myMachine.myEmployer.com ). Of course there is no machine by that latter name, and so it fails. Even weirder, once I disconnect from the VPN I can again ping myMachine successfully, but ICMP reports the machine by its MAC address instead of its IP address. I don't think I've ever seen ping identify another machine by its MAC address. So two questions: How can I access via RDP/ping the other machine BY NAME on my local network while also connected to the VPN? Why is ping identifying a MAC address for the machine on my home network, instead of an IP address? And how can I change this so that an IP address is reported instead? For question #1, I can indeed access the other machine on my home network by IP address. I suspect if I put the name-IP pair into my HOSTS file, then I would be able to access it even when connected to the VPN. But I wonder if there is another (more elegant) solution?

  Read the article

• What methods are available for updating a non-Internet-connected VMWare ESXi host?

  - by romandas

  I have a stand-alone installation of VMWare vSphere Essentials, with a vCenter Server and 3 ESXi 4.0 host servers. The environment is intended to remain as a stand-alone network, with the exception that I can "float" a workstation or server between the 'Net and the VMWare network for patches and maintenance. With other installations, where the Internet is available, I've used the vSphere Host Update utility to connect to VMWare and then apply the patches to the ESXi hosts. My problem is that this utility does not seem to function if it cannot connect to both VMWare and the ESXi host at the same time, as the scan for patches function will not scan the server without connecting to VMWare's site to sync its repository first. Even if I sync it, disconnect from the 'Net and connect to the VMWare network, it still won't scan hosts for required patches -- it will prompt for syncing with VMWare and if you click No to syncing, the scan does not occur. Does anyone know of other options for updating the ESXi hosts in some automated fashion? I believe I can manually pull down required patches and apply them, but this will not scale well, and in the future I'm sure I'll want something a bit more scalable.

  Read the article

• Sharing between Vista and Windows 7

  - by Metro Smurf

  Vista Ultimate 32 bit Windows 7 Ultimate 64 bit I've read through similar questions about sharing between Win7 and Vista, but none of them have resolved my issue of not being able to share between Win7 and Vista: Connecting to a Vista shared folder from Windows 7 Networking Windows 7 and Vista Enable File sharing in Windows Vista Previously I had previously had my Vista and XP system sharing back and forth without any problems. I was able to access the shares without entering a user name / password in the NT challenge prompt (note: account names and passwords were different on the Vista and XP systems). Currently I replaced my XP system with a Win7 system. Now, when I attempt to access shares to/from Vista / Win7, I am continually prompted with an NT challenge to enter my credentials. Things I've Verified/Tried Both systems are on the same workgroup. Win 7 is using the Home network. Vista is using the Private network. In other words, neither system is using a Public network profile. Enabled file sharing with and without password protection on both Vista and Win7 Tried HomeGroup Connections (win7) with Windows to manage connections and Use user accounts to connect. Reviewed too many online articles to count to trouble shoot. Set the shares to have full control by everyone. Set up the shares directly on the directory and through the share manager. My Question How can I enable file sharing between Vista and Win7 without being prompted with a username/password challenge, ever?

  Read the article

• How to configure network on Windows Server 2008

  - by Gokhan Ozturk

  I have a IBM x3400 Server Machine with Windows Server 2008 R2 installed on it. But, since I am not expert on networking I have some problems. These roles installed on my server: Active Directory DNS File Sharing Hyper-V ISS VPN There is two network card on them. I configured them like this: Local Connection 1: 192.168.30.3 255.255.255.0 192.168.30.2 127.0.0.1 Local Connection 2: 192.168.30.101 255.255.255.0 192.168.30.6 127.0.0.1 My problem is, when I use this Ip gateways, It is sharing internet to all computers. This is not I want. I want to use Local Connection 1 for internal network. I am giving all computers gateway and DNS IP as 192.168.30.3 The Local Connection 2 is for Hyper-V and VPN connections. 192.168.30.2 and 192.168.30.6 are my modem's gateways. I am using 192.168.30.6 external IP for VPN connections. There is two 24 port switches. There is a connection between them and this two ethernet card connected directly to them. And modems are connected to switches as well (Morems are not near the server. They are somewhere in the building). I disabled network Bridge and removed all ethernet cards from it. With this configuration, all computers can ping my server's IP (192.168.30.3) but on server I cannot ping any clients (Request timeout). What is the best way to configure my network? Thank you. Redgards

  Read the article

• Offloading backups to secondary network

  - by user1467163

  I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

  Read the article

• Can't open shared drive after disconnecting vpn

  - by Matt McMinn

  I use a VPN to connect to my office network. On my local network I have another WinXP machine that shares a printer and a few shared folders. While I'm connected to my work VPN, I can access the shared printer and folders on the other machine just fine, and vice versa. Once I disconnect the VPN, I can't access the local machine any more, and the other machine can't access my machine. The network itself seems ok - I can ping the other machine, get to the internet, and get on to a web server shared by the other machine, but I can't get to the shared folders or printer. If I reconnect to the VPN, my access is restored. I'm guessing this is some sort of authentication thing, but I don't know what. Any ideas? Update This problem is bothering me again, so here's an update. Depending on when I first access the WinXP machine, I either have this problem, or the opposite problem. After a reboot, if I (for example) print, then connect to the VPN, I can't access the machine while on the VPN. If after a reboot I connect to the VPN, then print, I can't access the machine off the VPN. In both cases, if I enable/disable the VPN again, I can access the machine again. Thanks

  Read the article

• Cisco configuration for public library internet

  - by AlternateZ

  I'm a C/C++ computer programmer turned IT support guy working for a public library. My day is usually spent helping random grandparents learn how to use email, so my networking knowledge is limited to what I can glean from google. Here's the situation. We have a public library with 20 PCs on a LAN and also public wifi access. Previously we were running all of this on 1 ADSL connection and people complained about low speeds. We hired a networking company to set up a Cisco dual-WAN router for us, and purchased an additional ADSL connection. The intention was to give the LAN PCs a guaranteed amount of bandwidth each, and then let the wifi users split the rest. The results were far worse than what we expected, and all we got from the company was excuses and they've since washed their hands of us. During busy periods, net performance on the LAN PCs are so poor that attaching files to gmail etc often times out and fails - far from the "guaranteed amount of bandwidth each" that we hope for! Sometimes it feels like performance is worse than before when we had 1 ADSL link and an unconfigured router? Anyways, surely this is a problem encountered a million times over across the world? (Sharing internet across many users effectively.) What are standard solutions for something like this? I admit to not even knowing the right jargon to google for (load balancing?) I'd appreciate any links to resources/guides that might help me get a better understanding of the problem/solutions, and perhaps some stories of your own experience in solving similar problems. This will help us evaluate and negotiate with network consultants in the future. If its relevant, our router config contains a section "policy-map" with "bandwidth percent" for each class of user (LAN, wifi), and "fair queue".

  Read the article

• IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

  - by NVRAM

  I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

  Read the article

• Hard Disk based storage library

  - by Ryan M.

  We have a Tandberg T24 tape device to handle all of our long term backups right now. We decided that we're not backing up nearly everything that we would like to and that we still have a lot of vulnerabilities. To get to where we want to be, we're going to have to back up a lot more servers than we're currently doing. All of our internal servers have some sort of directly attached drive (I.e. LaCie Raid box or a simple portable hard drive) doing backups, but what we want to do is get those backups off-site. The current tape drive is directly attached via SCSI to a Windows Server 2008 File Server. So to back up anything to tape, it has to be funneled through the File Server. With the current increase that we have planned, I don't think that funneling everything through the File Server is the right course of action and I'm thinking that maybe a second backup device would be more appropriate. I would like your input on a couple of ideas. 1) Doing HDD instead of tape. Tape is hard to deal with. We have a regular rotation cycle, so they don't need years and years of shelf life, so I'm wondering if something HDD-based would be better. 2) Something accessible over the network. Instead of having the device directly attached to one specific machine, have it available to all the servers over the network. Our File Server is a 12-disk raid 6 set up.. I was thinking something like that, but with no raid involved, all disks are stand alone so they can be used/installed/removed on an individual basis. Does any such thing exist? Thanks for your ideas. I'm really interested to hear about some of the solutions you guys are using..

  Read the article

• Creating a Logical network diagram

  - by user273284

  Im a student and I have been assigned the task of creating a logical network diagram for the following scenario There are 2 buildings, the first is the head office and the second is the branch. The data centre is in the head office, it contains domain controller, mail server, file server and a web server. it provides wired and wireless access to the staff. the branch building is new and it does not have a network. The two buildings must be connected using a VPN connection. The branch building will not have any servers but just network devices that will provide the connectivity, the users in the branch building will be connected to the head office over the VPN. I had created a diagram based on this scenario, but my teacher rejected it saying that it does not follow Cisco hierarchical Model and the servers were not placed correctly in the diagram. I just wanted some help in this matter so that I Can create my network diagram correctly. If anyone could upload a picture of how the logical diagram should be for this scenario will be helpful, any other resources would also be great.

  Read the article

• TCP/UDP hole punching from and to the same NAT network

  - by Luc

  I was wondering if tcp/udp hole punching would still work when you are in the same network (behind a NAT), and what the packet's path would be. What happens when using hole punching on the same network, is that it will send a packet out with the same destination and source address. Only the source and destination port would differ. I imagine a router with NAT loopback enabled will handle this as it should, but how about other routers? Would they drop the packet, or would a router (the first?) from the ISP bounce the packet back after which it gets handled okay? I'm wondering because I was thinking about using this technique to circumvent a block between peers in a network (like a school network where clients can only access the internet, but any contact with each other is blocked). The only other option is to use a man in the middle as proxy (tunnel?). The disadvantage of this is that you have to have a server with significantly more bandwidth than one that would only do hole punching. Also the latency would increase significantly.

  Read the article

• Open ports broken from internal network

  - by ksvi

  Quick summary: Forwarded port works from the outside world, but from the internal network using the external IP the connection is refused. This is a simplified situation to make the explanation easier: I have a computer that is running a service on port 12345. This computer has an internal IP 192.168.1.100 and is connected directly to a modem/router which has internal IP 192.168.1.1 and external (public, static) IP 1.2.3.4. (The router is TP-LINK TD-w8960N) I have set up port forwarding (virtual server) at port 12345 to go to port 12345 at 192.168.1.100. If I run telnet 192.168.1.100 12345 from the same computer everything works. But running telnet 1.2.3.4 12345 says connection refused. If I do this on another computer (on the same internal network, connected to the router) the same thing happens. This would seem like the port forwarding is not working. However... If I run a online port checking service on my external IP and the service port it says the port is open and I can see the remote server connecting and immediately closing connection. And using another computer that is connected to the internet using a mobile connection I can also use telnet 1.2.3.4 12345 and I get a working connection. So the port forwarding seems to be working, however using external IP from the internal network doesn't. I have no idea what can be causing this, since another setup very much like this (different router) works for me. I can access a service running on a server from inside the network both through the internal and external IP.

  Read the article

• Distributing Microsoft Office Template or Macro over the network

  - by zfranciscus

  We have around 400 users who use Word and we want to make their life easier by distributing templates and macros over the network. The easiest way to do this of course to setup a shared network folder and let them get the appropriate templates and macros. Of course, each user has to know where to copy these files to in their local PC, and we have to rely on constant email communication to let them know for newer version of the macro and templates. The next alternative is to ask them to configure Word to point to these network folder. But of course any disruption to the network means disruption to their work. We are thinking to setup a synchronization mechanism that downloads new templates to their local machine. We are also thinking to make this sync tool to prompt users that it will download new templates - you know just to give them visibility that they are receiving changes. We are wondering what is the best approach that people usually use in their workplaces ? Are there any specific tool that can make this task easier ?

  Read the article

• Suggestions for transitioning to new GW/private network

  - by Quinten

  I am replacing a private T1 link with a new firewall device with an ipsec tunnel for a branch office. I am trying to figure out the right way to transition folks at the new site over to the new connection, so that they default to using the much faster tunnel. Existing network: 192.168.254.0/24, gw 192.168.254.253 (Cisco router plugged in to private t1) Test network I have been using with ipsec tunnel: 192.168.1.0/24, gw 192.168.1.1 (pfsense fw plugged in to public internet), also plugged in to same switch as the old network. There are probably ~20-30 network devices in the existing subnet, about 5 with static IPs. The remote endpoint is already the firewall--I can't set up redundant links to the existing subnet. In other words, as soon as I change the tunnel configuration to point to 192.168.254.0/24, all devices in the existing subnet will stop working because they point to the wrong gateway. I'd like some ability to do this slowly--such that I can move over a few clients and verify the stability of the new link before moving critical services or less tolerant users over. What's the right way to do this? Change the netmask on all of the devices to /16, and update gateway to point to the new device? Could this cause any problems? Also, how should I handle DNS? The pfsense box is not aware of my Active Directory environment. But if I change DNS to use the local servers, it will result in a huge slowdown as DNS queries will still be routed over the private t1. I need some help coming up with a plan that's not too disruptive but will really let me thoroughly test the stability of the IPSEC tunnel before I make the final switch. The AD version is 2008R2, as are the servers. Workstations are mostly Windows XP SP3. I have not configured the 192.168.1.0/24 as a site in AD sites and services.

  Read the article

• IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

  - by NVRAM

  I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

  Read the article

• Route all traffic of home network through VPN

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: ==LAN== Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN ==WAN== Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >