Search Results

Search found 22600 results on 904 pages for 'remote connection'.

Page 100/904 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

  • Setting up wifi router as a switch for Internet Connection Sharing

    - by William C
    Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

    Read the article

  • Tomcat "connection interrupted" with ssl

    - by Mike Thomsen
    I can access Tomcat on port 8080, but not on 8443. When I try o get there, this is the error I get in Firefox: The connection was interrupted The connection to the.fqdn.com:8443 was interrupted while the page was loading. This is my connector: <Connector port="8443" protocol="org.apache.coyote.http11.Http11NioProtocol" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="want" sslProtocol="TLS" keystoreFile="C:\temp\keystore.jks" keystorePass="changeit"/> I have the CA key in the jre's cacerts file. The server cert was generated using EJBCA and should be signed properly. Any suggestions on what is going on?

    Read the article

  • HDMI connection does not support HDCP

    - by mroggi
    Hi, My problem: error message when playing blu-ray movies stating that the HDCP encryption could not be established. My setup: A new projector (EPSON EMP TW700) with a HDCP-compliant HDMI port a PC with a brand-new graphics adapter (Sapphire HD 4350 512MB DDR2) supporting HDCP Connection made with a DVI cable (it's installed in my wall) and a DVI-HDMI adapter to connect the projector Latest drivers and software My questions: What can I do to establish the HDCP connection? Would it help to use the HDMI output of the graphics adapter instead of the DVI (could it be that the HDCP chip is only supported on HDMI?) Any other ideas? I am very thankful for any hint.

    Read the article

  • Sharing internet connection with WDS

    - by cornjuliox
    Is it possible to share an internet connection through WDS? I'm on the very edge of a wireless network, the spot that I'm in maintains a stable 22% according to XP with the help of a parabolic reflector crafted from a cheap pie tin. I was thinking I could grab another wireless router, use WDS to bridge the this router with the other one and share the 'net connection through it thus giving me a little bit more freedom but when I tried it it didn't work. WDS looks like it bridged the networks just fine, but I couldn't access anything on the internet. Do I need to do anything special or is this just not possible?

    Read the article

  • Cannot access internet or remote network after connecting to Windows VPN

    - by Kiewic
    I set up a VPN by creating an incoming VPN connection (VPN server) in my Windows 8 machine at home (not a Windows Server). I forwarded the PPTP port in my router (port 1723) to this machine and enabled PPTP passthrough. In a second Windows 8 machine out of home, I created an outgoing VPN connection (VPN client). And I am able to connect to my home VPN, but I don't have access to any home resource or even internet. This is the output of the client ipconfig: And this are the settings of my VPN server: UPDATE: My VPN server has assigned the 192.168.1.144 IP adress at my home network. So, I tried setting the "IP address assignment" range from 192.168.1.150 to 192.168.1.200. And when a VPN client gets connected, it gets an address in that range, but it doesn't make any difference.

    Read the article

  • Sharing wireless internet connection between 2 Ubuntu 10.04 systems using cross-over cable

    - by Gary
    I have a Lenovo T60 with Ubuntu 10.04 connected with a cross-over cable to a Dell Vostro 1400, also running Ubuntu 10.04. My internet is coming into the Lenovo through an external wireless antennae, and I want to share the internet with the Dell. On the Lenovo: eth0 connection has IPv4 Settings 'Shared to other computers' I can ping the Dell (10.42.43.10) successfully I can use mtr to trace to www.google.com successfully On the Dell: eth0 connection has IPv4 Settings 'Automatic DHCP' I can ping the Lenovo (10.42.43.1) successfully when I use mtr to trace to www.google.com, I can only reach 10.42.43.1 I must be missing some setting, but cannot see what it is; can anyone help me?

    Read the article

  • bridge to share WiFi internet connection over eth0

    - by rubo77
    In this script there is implemented that you create a mesh network and connect other machines to your device to serve an internet connection with dhcp: echo "starting bridge to share internet connection over eth0" ifconfig eth0 up promisc brctl addbr br-freifunk brctl addif br-freifunk bat0 brctl addif br-freifunk eth0 echo "internet starting, this may take some minutes due to latency..." echo "(use" echo "tail -f /var/log/syslog" echo "in another window for debugging)" echo echo dhclient br-freifunk echo "The error 'Rather than invoking init scripts through /etc/init.d...' can be ignored:" dhclient br-freifunk # without bridge: dhclient bat0 This works fine with the freifunk-mesh network. But how can I serve internet in a normal case? I would like to connect to any open Wifi I find with my network-manager or wicd (yes, with the graphical GUI) and then start a small script that creates a bridge to my network-out on my laptop I use Ubuntu and my networkcards are eth0 and wlan0

    Read the article

  • SSH issues: Read from socket failed: Connection reset by peer

    - by nitins
    I compiled OpenSSH_6.6p1 on one of our server. I am able login via SSH to the upgraded server. But I am not able to connect to other servers running OpenSSH_6.6p1 or OpenSSH_5.8 from this. While connecting I am getting an error as below. Read from socket failed: Connection reset by peer On the destination server in the logs, I am seeing it as below. sshd: fatal: Read from socket failed: Connection reset by peer [preauth] I tried specifying the cipher_spec [ ssh -c aes128-ctr destination-server ] as mentioned in here and was able to connect. How can configure ssh to use the cipher by default? Why is the cipher required here?

    Read the article

  • Inbound connections using Internet Connection Sharing in Apple/Mac/Leopard

    - by tlianza
    I have a Mac mini which I'm using to give some other devices wireless access, by sharing it's Airport connection with the local ethernet, and that is plugged into a switch. All devices can get online no problem. (See how: http://www.macosxhints.com/article.php?story=20041112101646643 and http://www.macosxhints.com/article.php?story=20071223001432304 ) The issue is that I need to be able to connect in to these machines as well (at least, for the Slingbox to work). All the devices have 192.168.2.* addresses, and the rest of my local network is on 192.168.1.*. I tried setting a static route so that the 192.168.2.* addresses would use a gateway of 192.168.1.50 (my mac mini's address) but that didn't seem to help. Does anyone know if what I'm trying to do is possible? I admit I'm not certain what Internet Connection sharing is really doing under the hood... perhaps it just does basic nat, and doesn't do the type of routing I'm looking for. If so, anyone know if this is possible?

    Read the article

  • Server not accepting uploads

    - by Tatu Ulmanen
    I'm having a strange problem with my VPS: I can download files from it, I can use PuTTy to connect to it and all behaves normally. But sometimes, when I try to upload a file to the server or save a file via SFTP, the connection inexplicably fails. I am using jEdit to edit files remotely via SFTP. When it works, it works fine. When it doesn't, I get an error message: Cannot save: java.io.IOException: inputstream is closed Cannot save: java.io.IOException: 4: I can see that a temporary save file (#file.php#save#) is created on the server with a filesize of 0. So the connection works, but when it comes to sending the actual data, something fails. The same thing with WinSCP, but the error is different: Copying file fatally failed. Copying files to remote side failed. And I can always browse the server with PuTTy without a problem. I see nothing abnormal in any log files. Auth.log shows this when I try to save: sshd[32638]: Accepted password for - from - port 62272 ssh2 sshd[32638]: pam_unix(sshd:session): session opened for user - by (uid=0) sshd[32640]: subsystem request for sftp sshd[32638]: pam_unix(sshd:session): session closed for user - When I wait for a while (say, an hour), everything works fine again. It can't be a temporary ban, as I am still allowed to connect to the server, right? I know this may not be enough info to solve the problem, but I am grateful for any clues or bits of information that might help me. What are the possible causes for this kind of behaviour, what log files can I check for clues etc.. I'm running out of ideas!

    Read the article

  • Internet Connection Dying after some time

    - by Rahul
    I'm using BSNL 3G USB Datacard(BSNL is a ISP in India). After connecting to internet, while browsing in browser, the connection is dying. So after disconnecting & connecting back, it works proper for some time & the same problem repeats. But if I'm downloading any movie or some file through uTorrent, the connection is not dying. I'm experiencing this problem in Vista & also in Ubuntu. Help me with this please. Thank you.

    Read the article

  • Azure VM : Connection refused by host

    - by Simon Kérouack
    I recently stopped a subscription with 14 VMs in it and restarted it a few days later. Now all my VMs are working just fine at the exception of 6 used for MongoDB. They respond to ping and so they show as online in the azure dashboard but they do not answer to anything else. I tried (from different locations, in and out of the azure cloud) ssh : connect to host * port *: Connection refused telnet : Unable to connect to remote host: Connection refused mongo : exception: connect failed The ports for ssh and mongo are opened in azure. I tried restarting the VMs a few times trough the azure dashboard, they seem to restart successfully but still refuse all connections. I already looked for similar issues and the best solutions I found was to wait... the issue has been happening for 7 days and waiting is no more an option.

    Read the article

  • Windows 7 - Wireless connection before login possible?

    - by EJ
    Is there a way for Windows 7 to connect to a wireless network before a user has logged in? I have found no good answers to this question elsewhere. Some say it should already be happening if I am using Windows' connection management (WLAN AutoConnect, formerly WirelessZero), but I am using that, and it is not. I can sit at the login screen for as long as you please and it will not connect (watching the router from a separate PC), moments after I login it will connect. Others have said that you need to use the manufacturer's connection management (not Windows'), and they can sometimes have the option for prelogin/prelogon connections, but I am using generic drivers. The device is a Netgear/Cisco WMP300N, with a Broadcom chipset. Netgear/Cisco and Broadcom all claim to not have drivers for Win7, but Win7 apparently comes with a functional driver.

    Read the article

  • How to make Windows 7 use the internet connection that I specify

    - by user138957
    I have a LAN adapter and a USB wireless internet connection. When both connected windows 7 always uses the USB. I tried changing the metric values but no luck. Let me explains the steps I took. Currently automatic metric on all adapters. LAN connected. ipconfig shows that it is connected to the correct ip/dns/gateway etc. IPv4 Route table shows Metric 24 Then connected USB. ipconfig shows USB connectivity then LAN in that order. Internet is now through USB. IPv4 Route table shows Metric 4249 for LAN and USB is 41. Gateway for USB shows "on-link". netstat -rn shows USBDEVICE on top. Changed LAN metric to 5 and now the route table shows LAN as 9 (not sure why it added 4) and USB as 41. netstat shows LAN then USB. ipconfig shows LAN then USB. But still connection is through USB. How do I know? Task manager shows utilization only through USB as well as speed is showing around 1mbps rather than LANs 10mbps. How can I get win7 use LAN while USB is connected. I am just trying to use USB as a backup just in case I lose LAN connection. Please help!! I thought i will make USB metric manually to say 10. But it says I have to reconnect for it to be effective. Currently USB still shows below LAN and still has 9 and 41 in the table. Disconnected USB. Table shows LAN metric as 24 (Not sure why it got changed from 9 and setting got reverted by to automatic) Reconnected USB. Now in the setting still shows 10 and the route table shows 11 for USB and LAN shows 4249 (settings shows 4245, 4 less)) For some reason restarting USB is resetting LAN setting when reconnected. Thanks

    Read the article

  • How do I route traffic to website using a spcified network connection on Windows 7

    - by rwetzeler
    I want to route all traffic to a website over my wireless connection while the rest of the traffic using my lan. What I tried was first finding out the IP address of the website I want to go to. For example, lets say pandora.com. I found it resolves to 208.85.40.20. I have entered that entry into my hosts file. I then added that route using route add 208.85.40.20 mask 255.255.255.255 WirelessIP. It doesn't seem to work however. Instead of using the IP address, is there a way that I can just say.. this URL to route over that connection? Does anyone know of a program that I can install that will do this.. possibly some sort of proxy or a software load balancer that can do this?

    Read the article

  • Linux Mint on VirtualBox has no internet connection

    - by Martin
    Physical machine: Mac Mini running OSX 10.7.5 Virtual machine: Linux Mint 15 Cinnamon 64-bit Using VirtualBox. I am trying to make the linux connect to the internet. For some reason I can access the host computer with 192.168.2.100. Its set up to show me a web-page that says "It works". This I can see from the linux. But I cannot reach anything on the internet. Either FireFox says "Unable to connect" or when I run nslookup google.com I get connection timed out; no servers could be reached. My setting on VirtualBox under the Network tab are: Bridge Adapter vnic0 promiscouos Mode:Allow All`. If it makes a difference, the host has a WiFi connection to the home router. What have I missed?

    Read the article

  • Establish direct cable connection between Windows 8 PCs in home network

    - by Marie. P.
    I'm running two PCs, a desktop and a laptop with Windows 8 Release Preview ("Build 8400"). They are connected to the same router in infrastructure mode, thereby having wireless internet. Due to often file synchronization between the machines I want to establish a cable connection that allows direct file transfer, without needing to use the wireless. When I plug in the cable (normal, not cross-over), I see in "Control Panel\Network and Internet\Network Connections": "Ethernet - unidentified Network" on both PCs. Transferring a file between both still only uses the WiFi via the Router. I noticed that when turning off the wifi on one PC, I can set up a shared internet connection that will work via Ethernet-cable, but since sometimes only one PC runs, sometimes the other one, I do not want to have the internet of one machine to be dependent on the other one being switched on. I do not have a crossover-cable, but since I did connect the PCs already successfully (just without both being on the internet), I'm sure that this should also work with a normal ethernet cable.

    Read the article

  • connection with the application object server could not be established

    - by user44048
    Hello All, I have installed Axapta server on my Axapta(Machine name) machine. When i am going to start the axapta at that time it give error like " connection with the application object server could not be established ". Basic all the steps that i have tested like Service start restart and connection configuration. port number problem. Still i am not able to resolve a problem. please can any one tell me the solution. It's urgent please help as soon as possible. Thank you.

    Read the article

  • force connection using USB adapter

    - by James
    Hi all I am new to Linux, so even though this is probably a simple problem it remains unsolved after more then 3 hours of googling :-( I run running ubuntu 10.04 LTS on an Acer Aspire 5520G . the laptop has a wireless adapter, but since I wanted better range I got an Edimax EW-7711USN USB adapter. now , when running ifconfig I am able to see both adapters where as the laptop native adapter is listed as wlan0 and the usb adapter is listed as wlan1. but listing available networks from the wireless network applet , all the connection are listed under wlan0 , the usb adapter is costencly listed as disconnected. this is what I have been trying to do so far 1) ifconfig wlan0 down - I got disconnected from the net but still was not able to get the usb to connect 2) used the wireless connection dialog to connect to a hidden network with the usb adapter - I was able to connect to the network but with no Internet access 3) disable wireless using the laptop function button - both wireless adapters where disabled can anyone suggest a way to connect to to the wireless network using the USB adapter rather then the built in one ? Thanks

    Read the article

  • nginx errors: upstream timed out (110: Connection timed out)

    - by Sparsh Gupta
    Hi, I have a nginx server with 5 backend servers. We serve around 400-500 requests/second. I have started getting a large number of Upstream Timed out errors (110: Connection timed out) Error string in error.log looks like 2011/01/10 21:59:46 [error] 1153#0: *1699246778 upstream timed out (110: Connection timed out) while reading response header from upstream, client: {IP}, server: {domain}, request: "GET {URL} HTTP/1.1", upstream: "http://{backend_server}:80/{url}", host: "{domain}", referrer: "{referrer}" Any suggestions how to debug such errors. I am unable to find a munin plugin to keep a check on number of upstream errors. Sometime the number of errors per day is way too high and somedays its a more decent 3 digit number. A munin graph would probably help us finding out any pattern or correlation with anything else How can we make the number of such error as ZERO

    Read the article

  • Log connections to program

    - by Zac
    Besides for using iptables to log incoming connections.. Is there a way to log established inbound connections to a service that you don't have the source to (suppose the service doesn't log stuff like this on its own)? What I'm wanting to do is gather some information based on who's connecting to be able to tell things like what times of the day the service is being used the most, where in the world the main user base is, etc. I am aware I can use netstat and just hook it up to a cron script, but that might not be accurate, since the script could only run as frequently as a minute. Here is what I am thinking right now: Write a program that constantly polls netstat, looking for established connections that didn't appear in the previous poll. This idea seems like such a waste of cpu time though, since there may not be a new connection.. Write a wrapper program that accepts inbound connections on whatever port the service runs on, but then I wouldn't know how to pass that connection along to the real service. Edit: Just occurred to me that this question might be better for stackoverflow, though I am not certain. Sorry if this is the wrong place.

    Read the article

  • Apache SMTP connection times out

    - by Kaivosukeltaja
    A web server that has successfully sent mail using the hosting providers's SMTP server before seems to suddenly have lost connection to the SMTP server. [Wed Nov 28 09:51:27 2012] [error] [client 10.250.11.81] PHP Warning: fsockopen(): unable to connect to smtp.ourprovider.net:25 (Connection timed out) in /var/www/(....)/phpmailer/class.smtp.php on line 105, referer: http://oursite.net/sendmessage.php# If I telnet to the SMTP server's port 25 manually from the web server, I'm able to connect and send mail with no problems whatsoever. The web server is running RHEL 6.3 and Apache 2.2.15. The SE boolean httpd_can_network_connect is on. Our PHP version is 5.3.3. Where should I start looking to fix this?

    Read the article

  • Traffic shaping L2TP/IPsec VPN (via accounts not connection)

    - by Cromulent
    I need to be able to control the amount of bandwidth a specific user account can use on a VPN connection. One account I want to be able to use the VPN with no restrictions and another account I want to limit to a reasonable amount of bandwidth (say 10GB or so a month). I'm aware that you can traffic shape individual connections but that does not quite solve the problem as the limited account can just disconnect and reconnect to get a new connection. I need to be able to limit bandwidth on a login basis for a given period of time (monthly limit). I'm really not that familiar with traffic shaping in general so any advice would be appreciated. Thank you.

    Read the article

  • Connect to a particular network connection from terminal

    - by RanRag
    I am currently using Reliance netconnect USB modem. The problem I am facing is my USB modem disconnects itself at 22:00 PM IST everyday. Now, sometimes what I do is start some downloading and leave my laptop for 2-3 hours in this case if my network disconnects it is a problem for me. So, what I used to do in windows is make a python script and execute rasdial myconnection_name to automate the connection process in my absence. Now I want to achieve something similar in linux. So, what are my alternatives for rasdial like tool in linux to automatically connect to a particular connection . I am using ubuntu 12.04 and here is my nm-tool output.

    Read the article

  • Process vsserv.exe attempts connection to unknown host (clients.your-server.de)

    - by pushpraj
    from past few day I notice a new connection is being made from my system, I discovered it within the outpost firewall, it is blocked by default with the reason Block Transit Packets in the image above you can see that the process vsserv.exe is attempting a connection to static.88-198-155-41.clients.your-server.de I tried to search on google but could not find any relevant info, however this link http://www.webmasterworld.com/search_engine_spiders/3963600.htm says that your-server.de hosts bad bots. I am bit concerned if something is not correct. Could you help me understand the same?

    Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >