Search Results

Search found 3975 results on 159 pages for 'sound blaster'.

Page 100/159 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• Brightness Controls not working on HP Dm3t

  - by Karim

  i have an HP dm3t notebook which normally comes with windows 7. after some time i figured out how to install Windows XP on it. but now i am facing a problem that the brightess controls dont work so i am unable to change the brightess. the strange thing is that all the other buttons (sound volume, mute, sleep , etc... ) works but not the 2 brightess controls. i already downloaded the "HP Quick Launch Buttons" so i am asking about suggesitions how can i enable these two buttons in windows XP or even if i can change the brightess using some kind of software. thanks

  Read the article

• Clicks or ticks every minute when HDD is idle [closed]

  - by Ramy

  Possible Duplicate: Clicks or ticks every minute when HDD is idle My HDD is a My passport... It's 2 weeks old. I hear this tick or click followed by another one about 8-9 secs later, and they repeat every minute almost exactly... They usually happen and the LED light blinking.. It's not like the other clicks you hear that indicate any inevitable HDD failure, it's much lower in volume. I don't know what that is, however it's different than the rest of the HDD usual sounds...It's close to the sound of the mouse click. It sometimes also happens when I access a file on the drive mostly after being idle for a while, sometimes randomly not really sure... The drive though is working well, the SMART report comes out OK and without warning, and disk management shows it healthy... What could be the cause of this??

  Read the article

• Too big a difference between Loud and Quiet when watching DVD's... constantly have to adjust volume.

  - by Dan

  It is hard for me to find the right volume for my computer to watch my dvd's on because it seems like most reasonable volumes become overwhelming at the loudest parts of a movie and it is hard to even make out the dialog at the quietest parts. I find I'm constantly adjusting the volume during the course of a movie. Are there ways to make the difference between the louds and the quiets not so extreme? (both computer related solutions and non-computer related solutions welcome). Like moving my speakers across the room and increasing the volume? or the opposite? Or would would the extremes be less noticeable if I used headphones? Are there movie players that might have more complex sound adjustment features? If there is a software solution out there for linux that would be great too. Thanks, Dan

  Read the article

• Special function keys are mixed up on my Macbook Pro

  - by seanieb

  I recently sent my Macbook Pro (late 2008 model) to get a replaced logic board and top cover. When I got it back the Special function keys are mixed up. F3 - mutes sound - it should do expose f4 - decreases volume - it should show the dashboard f5 - increases volume ....etc, ... F11 - expose - it should decrease volume f12 - dashboard - it should increase volume I have checked and made sure that System PreferencesKeyboard"use all F keys as standard function keys" is not selected. And that no accessibility options are switched on either. How do I fix this? or should I bring it back to the repair shop? Thanks

  Read the article

• Drivers and Codec Compilations

  - by Pennf0lio

  Hi, Do you know any software or compilations that you recommend to handle drivers and codecs for newly formated computer? I am having problem gathering drivers and codecs when I format my computer or other's computer because we frequently misplace it's original drivers. I need an offline solution that doesn't need internet. Same for as the codec, when formating computer we frequently lost our codecs, are there codec packs you know that you would like to recommend? P.s. I had tried driver bot but it's only good when your online, I'm looking for a complete package that has all the driver to most common hardware (eg. Monitor, Sound, etc). Thanks!

  Read the article

• Why can't I reconnect to my Philips SHB9000 bluetooth headset?

  - by Thomas Eyde

  When I connected my Philips SHB9000 bluetooth to my Windows 7 (64 bit) for the very first time, it worked well. I had to manually change the default playback device, but otherwise it worked. Then, when I start up my computer from standby, it's nearly random when I can reconnect or not. My last option is to remove the bluetooth device and reconnect it. But now, even that doesn't work. The sad thing is, this used to work better on Windows 7 beta. Windows Update has a new driver which fails to install. Searching for this driver yields nothing. I thought all vendors had an official site for their drivers? Well, Philips seems to have none. If there is no answer to this problem, my advice is to NOT buy this headset. It's good looking, the sound is nice, but what need do we have from that if we can't use the bloody device?

  Read the article

• Creating a file server - How can I use a large VHD file in Hyper-V? (700GB)

  - by barfoon

  Hey everyone, After a few discussions (here, here, and here), I am still unable to create a simple VM that will be used as a fileserver hosted on my Hyper-V box. I have created a fixed 700GB SCSI drive (.vhd file), as I have learned an IDE drive of this size is not possible. Not to sound too cynical, but its blown me away at how much trouble its been to create a large amount of space and start using it. What is the best way to create a fileserver with a drive of this size hosted on Hyper-V Server 2008, and how can I get it going??? Inclusion of OS, driver, integration tools etc, anything you feel is required would be greatly appreciated. Extra information I am using the stand-alone version of Hyper-V server, and not Windows Server 2008. I have tried loading the Linux Integration Tools (linked in the comments of the last link above) onto a SUSE 11 VM and the installation fails, the machine cannot see the vhd at all. Thanks very much,

  Read the article

• Misbehaving Network Printers - options?

  - by Dan Kelly

  We are having some issue with printers on our network. We have 3 floors, 2 printers per floor (A3 & A4) all connected to the same Print Server. The issue is that the same printer may not behave the same on two different, seemingly identical desktops. The commonest place this is seen on our bulk print script in AutoCAD - occasionally drawings may print Landscape on Portrait paper, despite drawings always being Landscape... Does any one have any suggestions on what we can check / try? The current line of attack is to setup a new Print Server, with the HP universal print driver rather than the device specific drivers, and replace printers using exactly the same method on all desktops. Sound good?

  Read the article

• Problems with webcam

  - by Murtaza

  My friend is using Windows 8.1, and he has a webcam. He says it is working very well even without installing drivers. Webcam is A4tech - PK-331F. I asked for this webcam for use. I plugged in the webcam, and Windows detected it and installed drivers automatically. Then I opened Skype to check the webcam. I got a message from Skype that said, "Your webcam has microphone." When I clicked over it, it directed me to sound settings where it showed that the webcam microphone was working. I went to video settings, but the webcam wasn't listed there. As you can see in the image, the webcam is not listed. It is listed in Device Manager but isn't listed in Skype. I am using Windows 7 Professional. Any idea why this is happening?

  Read the article

• What version of Ubuntu to use for Desktop with 8Gb RAM?

  - by Alexander

  This may sound as a stupid question, but I am really interested whether Ubuntu Desktop i386 will be able to use all my available RAM. I want to use the latest, non-LTS version, 10.10. It says on the website that it's (i386) the Recommended version. I also recall that Flash Player had issues with 64 bit Linux. Also, the 64 bit version is listed in the Universal USB Installer as amd64. Does this mean that it's using instruction sets specific to AMD CPUs? (I have an Intel) Will it work fine with Intel? So which one to download and install? What to do to be able to use 8Gb of RAM?

  Read the article

• Video screen recording + add text (subtitle), export as .flv. What programs?

  - by RasmusWriedtLarsen

  I have to record a video to showcase a tool I've made. It's going to include my talking, but I also want some overlay text (subtitles) for people who doesn't have sound. I'm looking for a program that will let me add a text overlay (as subtitle) for my video, and if possible, export it as .flv . I've tried this so far: Used CamStudio for recording, using their lossless format. Converted the .avi file to a .flv using Any Video Converter (free version) I've been having some trouble with the output of CamStudio, some programs can't play the file right, it skips forward and backward. (VLC, Adobe Media Encoder CS4) So I'm looking for a program that accepts videos from CamStudio*, can add text to my video, and hopefully export as flv. *(If that's not possible I'm open for other recording programs). I'd like to ONLY use free programs, and I'm on Windows XP. Looking forward to your help :)

  Read the article

• How can I troubleshoot SSD disconnection problems on Windows 7?

  - by 0xC0000022L

  I have a small SSD (Transcend StoreJet TS256GESD200K) which I am using on several computers. The drive is formatted with NTFS and recently I started noticing disconnects. Normally one probably wouldn't notice (you don't even get the notification sound in Windows when it disconnects), but since I use USBDLM and run a VM from that SSD, I get to see this first-hand. How could I best figure out whether the problem is the hardware (SSD, USB socket, USB cable or something in the PC) or software? In short: how can I locate the source of the disruption so that I can work on removing the problem? Side-note: SMART status for the SSD is clean.

  Read the article

• Enable System Beep in Ubuntu

  - by Melissa W

  I have tried and tried to get the system beep working, but with no success. I have selected System--Sound--System Beep--Enable Audible Beep (from the Gnome Desktop) I have tried from a Terminal window Edit--General Tab--Selecting terminal bell checkbox I have tried entering modprobe pcspkr at the command line. Trying echo -e '\a' or using the beep application - Nothing works! I know my hardware speaker works, because if on startup the battery is low it will beep. Update: It is a laptop computer. It is an IBM Thinkpad, iSeries. I did look at the modprobe blacklist, and pcspkr was not listed.

  Read the article

• Problems with webcame

  - by Murtaza

  My friends is using windows 8.1 and he has a webcam. He says it is working very well even without installing drivers. Webcam is A4tech - PK-331F. I asked for this webcam for use. I plugged that that webcam and windows detected it and installed drivers automatically. Then I opened Skype for checking webcam. I got massage on top of Skype that "your webcam has microphone" when I clicked over it, it directed me to sound settings where I microphone of webcam was working. I went to videos settings but webcam wasn't listed their. As you can see in image. Webcam is listed in device manager but isn't listed in Skype. I am also using windows 7 professional. Any idea why it is happening?

  Read the article

• What's the simplest way to get .flac music files into iTunes?

  - by Chris Adams

  I'm looking for a simple way to import .flac files into iTunes, so I can play them on my mac, and when I'm out, my iPhone, and I'm willing to be I'm not the first person to want to do this. What are the best tools for doing this? The quality of the music is useful, but truth be told, the speakers I'd play them on are so crappy that a lot of the sound quality in the .flac format would be lost anyway, so I'm not averse to converting to mp3 files. If it helps give any context, I'm using a Macbook with OS 10.5 Leopard, and iTunes 9, connected to a 16gb iPhone with standard apple headphones, which is sometimes plugged into Bose SoundDock for music, and the music files are piano performances. C

  Read the article

• 389 DS Achitecture for Multiple Sites

  - by Kyle Flavin

  I'm looking to deploy 389 Directory in my environment to replace an existing iPlanet installation. I would be using it primarily to store user account data for authentication purposes. I have two physically separate data centers that I would like to share the same directory tree. My initial thinking is to setup 389 DS as follows: -A Master/Consumer in DataCenter A -A Master/Consumer in DataCenter B -Replication agreement between both masters, to mirror the directory tree in both environments. Does this sound like a reasonable approach? Is there a better way to do it? (ie: four masters?) Is there documentation for best practices when setting up 389 DS in situations such as this? Thanks.

  Read the article

• On Windows 7, how can I tell if a recording is multi-channel without third party tools? [migrated]

  - by engineerchuan

  A customer has an audio that is confidential and can't send it to me. He also would not like to install other tools. He has a basic Windows 7 install. Is there any way to tell whether the recording is one channel or two channel? Normally, I would just get the audio and soxi it. Or, I would tell him to install Audacity or equivalent sound editor and open it up. I also thought that if you right clicked and looked at the size, bit rate, and length, you could get number of channels but bit rate already factors in number of channels. Sorry I'm not giving you a lot to work with.

  Read the article

• Does laser printer use toner when switched on/off?

  - by Alan Harris-Reid

  I have recently purchased a HP LaserJet M175nw laser printer which goes into sleep-mode after 10 minutes of non-use. I know sleep-mode uses a very small amount of power, but the flashing light on the control panel is driving me nuts! I know I can turn-off the printer via. the on/off button, but when it is turned-on manually, there is some whirring sound which I guess might be the machine warming-up. My question is... Is any toner used during this warm-up (or cleaning) cycle? Am I better-off keeping the printer in sleep mode, or is it ok to turn off manually? TIA Alan

  Read the article

• Is it safe to use a single switch for multiple subnets?

  - by George Bailey

  For a moment, forget about whether the following is typical or easy to explain, is it safe and sound? Internet | ISP supplied router x.x.x.1 (public subnet) | switch-------------------------------------+ | (public subnet) | (public subnet) BVI router (switch with an access list) NAT router | (public subnet) | (private subnet 192.168.50.1) +--------------------------------switch----+ (both subnets) | | computer with IP 192.168.50.2 ------+ +----computer with IP x.x.x.2 I don't plan to implement this setup, but I am curious about it. The 50.2 computer may send a packet to the x.2 computer, but it will use 50.1 as the router, since 50.2 knows that the subnet is different. Would this result in the packet being received twice by the x.2 machine, first directly through the switch, second by way of the two routers? Do you see any problems with this aside from how confusing it is, and that it would put one switch doing the work of two subnets?

  Read the article

• What to do if you were scammed by a web hosting company? [on hold]

  - by Cain Nuke

  I was recently scammed by a web hosting company. Is there anything i can do about it? I would like to sue them but that doesn't sound realistic to me since they are not based on the same country as me. I would like to at least be able to have them blacklisted or something so other people don't get scammed too. I would appreciate if you can tell me how to proceed in these cases. They promise 24/7 support which is not true because its only one guy managing the whole thing and your server can go down for days and he doesn't do anything, he wont even reply your tickets. My server is been offline for over a week now and he only ignores me. I paid for this month and shortly after that my server went offline. I used Paypal to pay. He is in Bulgaria (that's what he says) i'm in Japan. I paid $55 USD.

  Read the article

• Movie colors are off on ubuntu

  - by chris

  I've been playing with a new SLR that also happens to record movies. When I try to view a movie using Movie Player, it plays fine, and the sound is there, but the colors are off - green grass is purple, and my golden retriever is a blue retriever. VLC reports that the file is broken, offers to repair it, and plays it with the same problem. The same file plays fine under WinXP with both Media Player and Quicktime, and with no problems under MacOS also with Quicktime. What's the problem, and how can I fix it?

  Read the article

• V4L2 and ALSA: Kernel SPI or User API?

  - by pnongrata

  I'm trying to understand what Video for linux and ALSA are (exactly), and I can't discern whether they're APIs for Linux application to use (the userspace) or if they are backend services that are only available to the Linux kernel (sort of a kernalspace SPI). Or, if they are something entirely different. On one hand, those articles make it sound like its an API for applications to use. However, on the V4L2 page it has a section title Software supporting Video4Linux... So is V4L2 a library that applications use, or is it a module that "snaps into" the kernel? I'm so coonfused, thanks in advance.

  Read the article

• Can I do an overwrite install of Windows 7 without losing all my apps and data?

  - by Brian Dougan

  My local computer technician installed his store's copy of Window's 7 Premium on my computer. I had been using Window's Vista; but needed the XP component of "7" As part of the price I paid; I have a fully licensed, unopened "7" disc; with all of the drivers included. The technician warned me about the "nag" screen; that asks me to install my licensed copy at any time. Without thinking; I downloaded all of my usual software programs before installing the licensed copy. Here is my question: I hope this won't sound obvious: Will it overwrite my downloads?

  Read the article

• Windows (7 & Vista) laptop monitor does not come back after closing lid

  - by Scott Vercuski

  I'm experiencing an issue with Windows Vista (and now Windows 7) with my laptop. When I close the laptop lid the monitor goes blank but will not come back on after I re-open the laptop. The screen stays blank and nothing that I do will get it to come back. The laptop is an HP DV9000 series. Has anyone else ran into this issue? One of the solutions I've seen online is to go into the device manager and replace the lid driver with something nonsensical (the website suggested pointing the driver at the sound recorder). This does solve the problem by disabling the lid but doesn't really resolve the root issue. I'm asking if anyone has any method I can use to debug what's going on. How do I tell if it is an operating system issue vs. a malfunction within the lid itself. I'd actually like the lid to function as it's meant to. Thank you!

  Read the article

• Tools to automate recording streaming radio

  - by Stan

  Are there any tools that can automate recording online streaming radio? I've been using Total Recorder which has the following useful features: Handy scheduler Supports creating recording templates, so I can customize some high/low quality recording Unfortunately it requires opening the streaming radio in a browser and can't have another sound source at the same time; it's recording what comes out from the speaker. What I am looking for is given an online radio URL, the tool should be able to record the audio stream, no matter if I am playing any other music or not. Does such a tool exist?

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >