I'm currently having a major problem with e1000e (not working at all) in Ubuntu Maverick (1.0.2-k4), after resume I'm getting a lot of stuff in dmesg:
[ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled
[ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4
[ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
[ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM L1
[ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64
[ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s
[ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session.
[ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74
[ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005302-003
[ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
and, a bunch of
[ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang:
[ 2128.005452] TDH <89>
[ 2128.005454] TDT <27>
[ 2128.005456] next_to_use <27>
[ 2128.005458] next_to_clean <88>
[ 2128.005460] buffer_info[next_to_clean]:
[ 2128.005463] time_stamp <6e608>
[ 2128.005465] next_to_watch <8a>
[ 2128.005467] jiffies <6f929>
[ 2128.005469] next_to_watch.status <0>
[ 2128.005471] MAC Status <80080703>
[ 2128.005473] PHY Status <796d>
[ 2128.005475] PHY 1000BASE-T Status <4000>
[ 2128.005477] PHY Extended Status <3000>
[ 2128.005480] PCI Status <10>
I decided to compile the latest stable e1000e to 1.2.17, now I'm getting:
[ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI
[ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation.
[ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM L1
[ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64
[ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s
[ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session.
[ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74
[ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003
[ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X
[ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex,
Flow Control: RX/TX
[ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
[ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9906.832056] eth0: no IPv6 routers present
With 1.2.20 I get:
[ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI
[ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation.
[ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM L1
[ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64
[ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s
[ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session.
[ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74
[ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003
[ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X
[ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex,
Flow Control: RX/TX
[ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
[ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 9722.920014] eth0: no IPv6 routers present
But, I'm still getting these
[ 9982.992851] PCI Status <10>
[ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang:
[ 9984.993606] TDH <5d>
[ 9984.993608] TDT <6b>
[ 9984.993611] next_to_use <6b>
[ 9984.993613] next_to_clean <5b>
[ 9984.993615] buffer_info[next_to_clean]:
[ 9984.993617] time_stamp <24da80>
[ 9984.993619] next_to_watch <5d>
[ 9984.993621] jiffies <24f200>
[ 9984.993624] next_to_watch.status <0>
[ 9984.993626] MAC Status <80080703>
[ 9984.993628] PHY Status <796d>
[ 9984.993630] PHY 1000BASE-T Status <4000>
[ 9984.993632] PHY Extended Status <3000>
[ 9984.993635] PCI Status <10>
[ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter
[ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex,
Flow Control: RX/TX
[ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO
I'm not sure where to start troubleshooting this. Any ideas?
Here is the result of ethtool -d eth0
MAC Registers
-------------
0x00000: CTRL (Device control register) 0x18100248
Endian mode (buffers): little
Link reset: reset
Set link up: 1
Invert Loss-Of-Signal: no
Receive
flow control: enabled
Transmit
flow control: enabled
VLAN mode: disabled
Auto speed detect: disabled
Speed select: 1000Mb/s
Force speed: no
Force duplex: no
0x00008: STATUS (Device status register) 0x80080703
Duplex: full
Link up: link config
TBI mode: disabled
Link speed: 10Mb/s
Bus type: PCI Express
Port number: 0
0x00100: RCTL (Receive control register) 0x04048002
Receiver: enabled
Store bad packets: disabled
Unicast promiscuous: disabled
Multicast promiscuous: disabled
Long packet: disabled
Descriptor minimum threshold size: 1/2
Broadcast accept mode: accept
VLAN filter: enabled
Canonical form indicator: disabled
Discard pause frames: filtered
Pass MAC control frames: don't pass
Receive buffer size: 2048
0x02808: RDLEN (Receive desc length) 0x00001000
0x02810: RDH (Receive desc head) 0x00000001
0x02818: RDT (Receive desc tail) 0x000000F0
0x02820: RDTR (Receive delay timer) 0x00000000
0x00400: TCTL (Transmit ctrl register) 0x3103F0FA
Transmitter: enabled
Pad short packets: enabled
Software XOFF Transmission: disabled
Re-transmit on late collision: enabled
0x03808: TDLEN (Transmit desc length) 0x00001000
0x03810: TDH (Transmit desc head) 0x00000000
0x03818: TDT (Transmit desc tail) 0x00000000
0x03820: TIDV (Transmit delay timer) 0x00000008
PHY type: IGP2
and ethtool -c eth0
Coalesce parameters for eth0:
Adaptive RX: off TX: off
stats-block-usecs: 0
sample-interval: 0
pkt-rate-low: 0
pkt-rate-high: 0
rx-usecs: 3
rx-frames: 0
rx-usecs-irq: 0
rx-frames-irq: 0
tx-usecs: 0
tx-frames: 0
tx-usecs-irq: 0
tx-frames-irq: 0
rx-usecs-low: 0
rx-frame-low: 0
tx-usecs-low: 0
tx-frame-low: 0
rx-usecs-high: 0
rx-frame-high: 0
tx-usecs-high: 0
tx-frame-high: 0
Here is also the lspci -vvv for this controller
02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
Subsystem: Lenovo ThinkPad X60s
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 2000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 415a
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-0a-e4-ff-ff-3e-ce-74
Kernel driver in use: e1000e
Kernel modules: e1000e
I filed a bug on this upstream, still no idea how to get more useful information.
Here is a the result of the running that script
EEPROM FIX UPDATE
$ sudo bash fixeep-82573-dspd.sh eth0
eth0: is a "82573L Gigabit Ethernet Controller"
This fixup is applicable to your hardware
Your eeprom is up to date, no changes were made
Do I still need to do anything? Also here is my EEPROM dump
$ sudo ethtool -e eth0
Offset Values
------ ------
0x0000 00 0a e4 3e ce 74 30 0b b2 ff 51 00 ff ff ff ff
0x0010 53 00 03 02 6b 02 7e 20 aa 17 9a 10 86 80 df 80
0x0020 00 00 00 20 54 7e 00 00 14 00 da 00 04 00 00 27
0x0030 c9 6c 50 31 3e 07 0b 04 8b 29 00 00 00 f0 02 0f
0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff
0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00
0x0060 00 01 00 40 1f 12 07 40 ff ff ff ff ff ff ff ff
0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff 4a e0
I'd also like to note that I used eth0 every day for years and until recently never had an issue.
