Search Results

Search found 18594 results on 744 pages for 'computer science student'.

Page 101/744 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

• How can I install iTunes in such a way that it can't put any "hooks" or helper programs on my computer?

  - by Joshua Carmody

  I'm buying a new iPad, which means I must once again install iTunes. I've not used iTunes in more than 6 months, since I bought a new computer. I don't like iTunes, but I can live with using it to buy/manage media and sync my Apple devices when the program is open. What I would like to do though, is find a way to install iTunes in such a way that it has absolutely no effect on my system when it is closed. iTunes normally installs several helper programs such as iTunesHelper.exe, and the Bonjour service. These programs run in the background when iTunes is closed. You can force-close them, or remove them from your setup files, but iTunes will often put them right back when you run it. I know these programs are mostly harmless, but they have at times caused issues such as iTunes spending system resources trying to catalog media files or drives connected to VPN, or other issues. At best they're just one more small background process eating up a small piece of my CPU time and RAM. How can I run iTunes without letting it get it's "hooks" into my system? One thought I had is that I could create a Windows user account just for iTunes, and deny it admin privileges. Then if I installed iTunes using that account maybe anything it installed wouldn't affect the "main" account on my PC? But I'm not sure if that would work.... Failing that, maybe some kind of virtualization software or sandbox I could install it in? I'm open to any suggestions. My system is an Intel-based PC running Windows 7 Professional 64-bit. Thanks!

  Read the article

• Computer hangs at BIOS screen. Cannot enter setup.

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• Who should I run mysql as, on a personal computer?

  - by user664833

  I just installed mysql via homebrew (with brew install mysql, on Mac OS X Mountain Lion - recently installed from scratch). Following the installation, there is a "caveats" section with options around further necessary actions to take: ==> Caveats Set up databases to run AS YOUR USER ACCOUNT with: unset TMPDIR mysql_install_db --verbose --user=`whoami` --basedir="$(brew --prefix mysql)" --datadir=/usr/local/var/mysql --tmpdir=/tmp To set up base tables in another folder, or use a different user to run mysqld, view the help for mysqld_install_db: mysql_install_db --help and view the MySQL documentation: * http://dev.mysql.com/doc/refman/5.5/en/mysql-install-db.html * http://dev.mysql.com/doc/refman/5.5/en/default-privileges.html To run as, for instance, user "mysql", you may need to `sudo`: sudo mysql_install_db ...options... Start mysqld manually with: mysql.server start Note: if this fails, you probably forgot to run the first two steps up above A "/etc/my.cnf" from another install may interfere with a Homebrew-built server starting up correctly. To connect: mysql -uroot To launch on startup: * if this is your first install: mkdir -p ~/Library/LaunchAgents cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist * if this is an upgrade and you already have the homebrew.mxcl.mysql.plist loaded: launchctl unload -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist cp /usr/local/Cellar/mysql/5.5.27/homebrew.mxcl.mysql.plist ~/Library/LaunchAgents/ launchctl load -w ~/Library/LaunchAgents/homebrew.mxcl.mysql.plist You may also need to edit the plist to use the correct "UserName". On previous versions of Mac OS X I ran mysql as mysql user, but now I am confronted by the idea of running it as myself. I am the only one who uses this computer (which happens to be my laptop), and I do programming for work and for pleasure. What are the pros & cons, or best practices, around choosing whether to run mysql AS YOUR USER ACCOUNT or as mysql or something else still?

  Read the article

• Why does my computer sometimes not identify my wireless network, or others, that it always connects to?

  - by Emile Erasmus

  I have a vista operating system. Sometimes my computer will not connect to the wireless network (internet) when I start up my laptop. This happens at different places on occasion, and it is very random. It tries to connect, but can not identify the network (it does recognize the wifi name). So at the end it connects, but with limited connectivity. It can not be the hardware because all other computers connect to it fine at the same time. And it happens at different places, mostly home, but sometimes at coffee shops, etc. And then in a day or two when I start up my laptop it is all of a sudden working again. (restart does not solve the problem). I have tried all the trouble shooting options windows offers, restarting the notebook, switch modem on and off, switch laptop wifi on and of, deleted the wifi memory from the laptop and reconnected with the password as if it was the first time, everything. If it does not work at one place it does not mean it won't work at another. Example it won't work at home, then I go to coffee shop and it works, then get back home and it don't. Anyone encountered this before?

  Read the article

• Conditional Lookup in Excel

  - by Keyslinger

  I want to use excel to compare pairs of numbers from the "Pre/Post" column of the following data: Student Course Pre/Post Score K300997203 FHS120100417 Pre 3 L286197217 FHS120100417 Pre 5 S106497203 FHS120100417 Pre 4 K300997203 FHS120100417 Post 4 L286197217 FHS120100417 Post 4 S106497203 FHS120100417 Post 4 S106497203 FHS220100424 Pre 4 Specifically, I want a cell to contain the difference of the value in the "Score" column where "Pre" and "Post" appear, respectively, in rows with the same value in the "Student" and "Course" columns. For example, Student K300997203 has a row containing Course FHS120100417, a score of 3, and "Pre" AND Student K300997203 has a row containing Course FHS120100417, a score of 4, and "Post". How can I calculate a cell value as the score in the row containing "Post" minus the score in the row containing "Pre"?

  Read the article

• Why is my computer randomly restarting? How can I fix it?

  - by kinglime

  I have a custom built desktop computer that I've been using since about a year ago. The main specs are: ASUS P8Z68-V LE Motherboard Intel Core i7 2600k Corsair Vengeance 16GB Ram ASUS ENGTX570 GPU Corsair TX650M PSU I was running an overclock of 4.4ghz for my cpu (I have a Hyper212 EVO) and 1600mhz for my RAM but have it currently turned off due to my issues. I am also currently running Windows 8 but this problem occured in Windows 7 too. Basically my issue is that seemingly randomly, with no pattern my PC will reset itself and ASUS Anti-Surge will alert me that something went wrong. This issue is not related to system stress. I can run it fine for an hour maxxed out on Prime95 then later I can be watching a mere YouTube video when it will randomly reset. This has been occurring probably for the last two weeks and it seems to be getting worse. I believe this might be related to the power supply but when I monitor it in the bios and in Windows it appears to be putting out the proper voltages. Also possibly related or not but my Nvidia drivers frequently temporarily fail and then warn me of some kind of kernel error? If I have to buy a new power supply that is what I'll do but I want to make damn sure that's the only issue at hand. Thank you everyone in advance, please help me diagnose the issue and tell me what I can do to fix it. If you need any additional info about my setup please ask me.

  Read the article

• Should I buy more RAM for my computer or a better CPU?

  - by Reijer The Coder

  I have recently bought a new laptop, an ASUS N56VJ-S4149H. I bought it to use it in all possible ways I could want, so that would be gaming downloading and streaming movies browsing the web and programming software. So far it has been running great but one thing annoys me a little bit. I frequently play Mount&Blade: Warband, it's a great game and you should check it out. Everything runs smoothly but only when I turn down the 'Texture Detail'. Otherwise it will lag a lot and I can't really play. Now my question is: Is this a problem of not enough RAM? At first I was really sure it was but after thinking about for a while I'm not anymore. My computer only has 4 Gigabytes of RAM and there is still a slot open. So will it improve when I buy another 8 Gigabytes? EDIT: It has an Nvidia GeForce GT 635M inside. and an Intel Core i5 3230M CPU with 2,6 GHz. Help and answers are really appreciated. Thanks to all.

  Read the article

• Which scripting language to use to asynchronously ssh into equipment, run several commands, parse the output, and save to a file on my computer?

  - by Fujin

  There are several points I'd like to stress in my question. I'd like to login by asynchronously ssh'ing into our infrastructure equipment. Meaning, I do not want to connect to only one device, do all the tasks I need, disconnect, then connect to the next device. I want to connect to several devices at once in order to make the process as fast as possible. By equipment I mean 'infrastructure equipment' and not servers. I say this because I will not have the luxury of saving files to the device then transferring them to myself with scp or another method. The output of the scripts that are run will have to be saved directly to my computer. The output of the commands that are run will need to be cleaned up and parsed. Also I want the outputs of each device to be combined into one nice and neat file, not a separate file for each device. This will all be done from a linux box, using ssh, into devices that all use linux'ish proprietary OSes. My guess is the answer to my question will either be a Bash, Perl, or Python script but I figured it wouldn't hurt to ask and to hear the reasons why one way is better than another. Thanks everyone. EXTRA CREDIT: With you answer, include links to resources that will help create the script I described in the language that you suggested.

  Read the article

• Support our movement?

  - by Mirchi Sid

  | Imagine Freedom 2013 | mnearth Student Programs This is to inform you about the world’s first online student competition called imagine freedom which is conducted by mnearth corporation India .The imagine freedom will be one of the most popular student IT competition in the world .The program will be fully functioned with free and open source software and operating system like Ubuntu Linux and Linux . The Competition have a lot of other categories like web designing , software development and much more .The program coordinates will contact your schools for the selection process and giving the first steps for registration . If you are an expert in Open source free software? Then it is the time for you ! Otherwise do you know anyone who have the skills ? Then inform them about the program . The competitions will be done as a part of Mnearth Student Programs . The program schedule and the local competition information will be send after getting the applications . The competitions are categorized into three . |Categories Of Participants Animation Films Multimedia Presentation 3D Animation Web Designing Software Development Innovations Cloud Apps Games etc. . . . . . |Levels Of Participants High School Level Higher Secondary Level Collage Level University Level |High School level This levels is for the students who is students . It’s age limit is 12 - 24 years . The competitions will be started on this year for selecting the good students who have the talent . For more information Send to : [email protected] Call us on :04936312206 (india) Join with the Community on facebook : follow us on twitter : www.twitter.com/imaginatingkids www.facebook.com/imaginefreedomonce

  Read the article

• Public class DiscoLight help

  - by luvthug

  Hi All, If some one can point me in the right direction for this code for my assigment I would really appreciate it. I have pasted the whole code that I need to complete but I need help with the following method public void changeColour(Circle aCircle) which is meant to allow to change the colour of the circle randomly, if 0 comes the light of the circle sgould change to red, 1 for green and 2 for purple. public class DiscoLight { /* instance variables */ private Circle light; // simulates a circular disco light in the Shapes window private Random randomNumberGenerator; /** * Default constructor for objects of class DiscoLight */ public DiscoLight() { super(); this.randomNumberGenerator = new Random(); } /** * Returns a randomly generated int between 0 (inclusive) * and number (exclusive). For example if number is 6, * the method will return one of 0, 1, 2, 3, 4, or 5. */ public int getRandomInt(int number) { return this.randomNumberGenerator.nextInt(number); } /** * student to write code and comment here for setLight(Circle) for Q4(i) */ public void setLight(Circle aCircle) { this.light = aCircle; } /** * student to write code and comment here for getLight() for Q4(i) */ public Circle getLight() { return this.light; } /** * Sets the argument to have a diameter of 50, an xPos * of 122, a yPos of 162 and the colour GREEN. * The method then sets the receiver's instance variable * light, to the argument aCircle. */ public void addLight(Circle aCircle) { //Student to write code here, Q4(ii) this.light = aCircle; this.light.setDiameter(50); this.light.setXPos(122); this.light.setYPos(162); this.light.setColour(OUColour.GREEN); } /** * Randomly sets the colour of the instance variable * light to red, green, or purple. */ public void changeColour(Circle aCircle) { //student to write code here, Q4(iii) if (getRandomInt() == 0) { this.light.setColour(OUColour.RED); } if (this.getRandomInt().equals(1)) { this.light.setColour(OUColour.GREEN); } else if (this.getRandomInt().equals(2)) { this.light.setColour(OUColour.PURPLE); } } /** * Grows the diameter of the circle referenced by the * receiver's instance variable light, to the argument size. * The diameter is incremented in steps of 2, * the xPos and yPos are decremented in steps of 1 until the * diameter reaches the value given by size. * Between each step there is a random colour change. The message * delay(anInt) is used to slow down the graphical interface, as required. */ public void grow(int size) { //student to write code here, Q4(iv) } /** * Shrinks the diameter of the circle referenced by the * receiver's instance variable light, to the argument size. * The diameter is decremented in steps of 2, * the xPos and yPos are incremented in steps of 1 until the * diameter reaches the value given by size. * Between each step there is a random colour change. The message * delay(anInt) is used to slow down the graphical interface, as required. */ public void shrink(int size) { //student to write code here, Q4(v) } /** * Expands the diameter of the light by the amount given by * sizeIncrease (changing colour as it grows). * * The method then contracts the light until it reaches its * original size (changing colour as it shrinks). */ public void lightCycle(int sizeIncrease) { //student to write code here, Q4(vi) } /** * Prompts the user for number of growing and shrinking * cycles. Then prompts the user for the number of units * by which to increase the diameter of light. * Method then performs the requested growing and * shrinking cycles. */ public void runLight() { //student to write code here, Q4(vii) } /** * Causes execution to pause by time number of milliseconds */ private void delay(int time) { try { Thread.sleep(time); } catch (Exception e) { System.out.println(e); } } }

  Read the article

• Desktop Applications Versus Web Applications

  Up until the advent of the internet programmers really only developed one type of application used by end-users.  This type of application was called a desktop application. As the name implies, these applications ran strictly from a desktop computer, and were limited by the resources available to the computer. Initially, this type of applications did not need resources outside of the scope of the computer in which they installed. The problem with this type of application is that if multiple end-users need to access the same desktop application, then the application must be installed on the end-user’s computer. In this age of software development security was not as big of a concern as it is today with other types of applications. This is primarily due to the fact that an end-user must have access to the computer where the software is installed in order for them to access the application. In addition, developers could also password protect the application just in case an authorized end-user was able to gain access to the computer. With the birth of the internet a second form of application emerged because developers were trying to solve inherent issues with the preexisting desktop application. One of the solutions to overcome some of the short comings of desktop applications is the web application. Web applications are hosted on a centralized server and clients only need to have network access and a web browser in order to access the application. Because a web application can be installed on a remote server it removes the need for individual installations of the same application on each end-user’s computer.  The main benefits to an application being hosted on a server is increased accessibility to the application due to the fact that nothing has to be installed on a desktop computer for an end-user to be able to access the application. In addition, web applications are much easier to maintain because any change to the application is applied on the server and is inherently applied to any end-user trying to use the application. This removes the time needed to install and maintain individual installations of a desktop application. However with the increased accessibility there are additional costs that are incurred compared to a desktop application because of the additional cost and maintenance of a server hosting the application. Typically, after a desktop application is purchased there are no additional reoccurring fees associated with the application.  When developing a web based application there are additional considerations that must be addressed compared to a desktop application. The added benefit of increased accessibility also now adds a new failure point when trying to gain access to an application. An end-user now must have network connectivity in order to access the application. This issue is not a concern for desktop applications because there resources are typically bound to the computer in which they run. Since the availability of an application is increased with the use of the client-server model in a web based application, additional security concerns now come in to play. As stated before a, desktop application is bound to the accessibility of the end-user to the computer that the application is installed. This is not the case with web based applications because they potentially could have access from anywhere with the proper internet/network connection. Additional security steps are required to insure the integrity of the application and its data. Examples of these steps include and are not limited to the following: Restricted/Password Areas This form of security is used when specific information can only be accessed by end-users based on a set of accessibility rules. IP Restrictions This form of security is used when only specific locations need to access an application. This form of security is applied from within the web server or a firewall. Network Restrictions (Firewalls) This form of security is used to contain access to an application within a specific sub set of a network. Data Encryption This form of security is used transform personally identifiable information in to something unreadable so that it can be stored for future use. Encrypted Protocols (HTTPS) This form of security is used to prevent others from reading messages being sent between applications over a network.

  Read the article

• Government Mandates and Programming Languages

  A recent SEC proposal (which, at over 600 pages, I havent read in any detail) includes the following: We are proposing to require the filing of a computer program (the waterfall computer program, as defined in the proposed rule) of the contractual cash flow provisions of the securities in the form of downloadable source code in Python, a commonly used computer programming language that is open source and interpretive. The computer program would be tagged in XML and required to be filed with the Commission as an exhibit. Under our proposal, the filed source code for the computer program, when downloaded and run (by loading it into an open Python session on the investors computer), would be required to allow the user to programmatically input information from the asset data file that we are proposing to require as described above. We believe that, with the waterfall computer program and the asset data file, investors would be better able to conduct their own evaluations of ABS and may be less likely to be dependent on the opinions of credit rating agencies. With respect to any registration statement on Form SF-1 (Section 239.44) or Form SF-3 (Section 239.45) relating to an offering of an asset-backed security that is required to comply with Item 1113(h) of Regulation AB, the Waterfall Computer Program (as defined in Item 1113(h)(1) of Regulation AB) must be written in the Python programming language and able to be downloaded and run on a local computer properly configured with a Python interpreter. The Waterfall Computer Program should be filed in the manner specified in the EDGAR Filer Manual. I dont see how it can be in investors best interests that the SEC demand a particular programming language be used for software related to investment data.  I have a feeling that investors who use computers at all already have software with which they are familiar, and that the vast majority of them are not running an open source scripting language on their machines to do their financial analysis.  In fact, I would wager that most of them are using tools like Excel, and if they really need to script anything, its being done with VBA in Excel. Now, Im not proposing that the SEC should require that the data be provided in Excel format with VBA scripts included so everyone can easily access the data (despite the fact that this would actually be pretty useful generally).  Rather, I think it is ill-advised for a government agency to make recommendations of this nature, period.  If the goal of the recommendation is to ensure that the way things work is codified in a transparent manner, than I can certainly respect that.  It seems to me that this could be accomplished without dictating the technology to use.  To wit: An Excel document could contain all of the data as well as the formulae necessary, and most likely would not require the end-user to install anything on their machine The SEC could simply create a calculator in the cloud such that any/all investors could use a single canonical web-based (or web service based) tool Millions of Java and .NET developers could write their own implementations You can read more about this issue, including the favorable position on it, on Jayanth Varmas blog. Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• My server is slower than the average user's computer, should I still offload Access queries to SQL Server? [closed]

  - by andrewb

  Possible Duplicate: How do you do Load Testing and Capacity Planning for Databases I have a database set up with MS Access 2007 front ends and an SQL Server 2005 back end. At the moment, all the queries are saved in the front end as I've only recently moved to an SQL Server backend. I'm wondering how much of those queries I should save as stored procedures/views on SQL Server. About the system The number of concurrent users is only a handful, though it could be as high as 25 at one time (very unlikely). The average computer has an Intel i3-2120 CPU running at 3.3 GHz, which gets a PassMark score of 3,987, whilst the server has an Intel Xeon E5335 running at 2.0 GHz, which gets a PassMark score of 2,637. Always an awkward situation when an i3 outperforms a Xeon... though the i3 is from Q1 2011 and the Xeon is Q2 2009. There is potential for a server upgrade in the future, though it wouldn't come easy. I'm inclined to move the queries to the back end, as they are beginning to take noticeable time and I figure that is a better way of doing things. I like the idea of throwing everything at the server, then pushing for a server upgrade. It makes more sense in my mind to be upgrading one server rather than 30 PCs. Or am I being overzealous? Why my question isn't a duplicate It seems that my question has been misinterpreted and labelled a duplicate of quite a different question, one about testing and capacity planning. I'll try explain how my question is very different from the linked question. The crux of my question is something like "Even though my server is technically slower, is it better to have it doing more of the queries?" There's two ways that people could have answered this: I agree the server is going to be slower, but the extra benefits of such and such (like the less Access the better) means you should move most to the server anyway. (OR no it doesn't outweigh the benefit, keep them in Access) Actually the server will be faster because of such and such. I'm hoping that people out there could provide some answers like this, and the question in the dupe link doesn't really provide either of these answers. Ok sure, I suppose I could do extensive performance testing to compare Access queries running on a local machine to SQL Server queries running on the server, but that sounds like a very hard task (particularly performance testing of access) compared to someone giving some quick general guidance, and again, my question is looking for a lot more than immediate performance benefit.

  Read the article

• How did what appears to be a virus get on my computer? (explanation of situation enclosed)

  - by Massimo

  My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

  Read the article

• Computer suddenly dies; screen displays weird flickering lines, then restarts

  - by Imray

  I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

  Read the article

• Macbook Pro Wireless Reconnecting

  - by A Student at a University

  I'm using a WPA2 EAP network. I'm sitting next to the access point. The connection keeps dropping and taking ~10 seconds to reconnect. My other devices are staying online. What's causing it? syslog: 01:21:10 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:21:10 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed reboot -> renew 01:21:10 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:21:10 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:21:10 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:21:10 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:33:30 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:33:30 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:33:30 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:13 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:14 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:14 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:14 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> 4-way handshake 01:35:14 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:14 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:17 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> disconnected 01:35:17 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:26 wpa_supplicant[XX60]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys 01:35:26 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:29 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 8 -> 3 (reason 11) 01:35:32 NetworkManager[XX40]: <info> (eth1): deactivating device (reason: 11). 01:35:32 NetworkManager[XX40]: <info> (eth1): canceled DHCP transaction, DHCP client pid XX27 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) starting connection 'Auto XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 3 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> disconnected 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): access point 'Auto XXXXXXXXXX' has security, but secrets are required. 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 6 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) started... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 6 -> 4 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) scheduled... 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 1 of 5 (Device Prepare) complete. 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) starting... 01:35:32 NetworkManager[XX40]: <info> (eth1): device state change: 4 -> 5 (reason 0) 01:35:32 NetworkManager[XX40]: <info> Activation (eth1/wireless): connection 'Auto XXXXXXXXXX' has security, and secrets exist. No new secrets needed. 01:35:32 NetworkManager[XX40]: <info> Config: added 'ssid' value 'XXXXXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Config: added 'scan_ssid' value '1' 01:35:32 NetworkManager[XX40]: <info> Config: added 'key_mgmt' value 'WPA-EAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'password' value '<omitted>' 01:35:32 NetworkManager[XX40]: <info> Config: added 'eap' value 'PEAP' 01:35:32 NetworkManager[XX40]: <info> Config: added 'fragment_size' value 'XXX0' 01:35:32 NetworkManager[XX40]: <info> Config: added 'phase2' value 'auth=MSCHAPV2' 01:35:32 NetworkManager[XX40]: <info> Config: added 'ca_cert' value '/etc/ssl/certs/Equifax_Secure_CA.pem' 01:35:32 NetworkManager[XX40]: <info> Config: added 'identity' value 'XXXXXXX' 01:35:32 NetworkManager[XX40]: <info> Activation (eth1) Stage 2 of 5 (Device Configure) complete. 01:35:32 NetworkManager[XX40]: <info> Config: set interface ap_scan to 1 01:35:32 NetworkManager[XX40]: <info> (eth1): supplicant connection state: disconnected -> scanning 01:35:36 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: scanning -> associated 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-STARTED EAP authentication started 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-METHOD EAP vendor 0 method 25 (PEAP) selected 01:35:36 wpa_supplicant[XX60]: EAP-MSCHAPV2: Authentication succeeded 01:35:36 wpa_supplicant[XX60]: EAP-TLV: TLV Result - Success - EAP-TLV/Phase2 Completed 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-EAP-SUCCESS EAP authentication completed successfully 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:36 wpa_supplicant[XX60]: WPA: Could not find AP from the scan results 01:35:36 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:36 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:36 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:35:36 NetworkManager[XX40]: <info> Activation (eth1/wireless) Stage 2 of 5 (Device Configure) successful. Connected to wireless network 'XXXXXXXXXX'. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) scheduled. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) started... 01:35:36 NetworkManager[XX40]: <info> (eth1): device state change: 5 -> 7 (reason 0) 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Beginning DHCPv4 transaction (timeout in 45 seconds) 01:35:36 NetworkManager[XX40]: <info> dhclient started with pid XX87 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 3 of 5 (IP Configure Start) complete. 01:35:36 dhclient: Internet Systems Consortium DHCP Client VXXX.XXX.XXX 01:35:36 dhclient: Copyright 2004-2009 Internet Systems Consortium. 01:35:36 dhclient: All rights reserved. 01:35:36 dhclient: For info, please visit https://www.isc.org/software/dhcp/ 01:35:36 dhclient: 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed nbi -> preinit 01:35:36 dhclient: Listening on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on LPF/eth1/XX:XX:XX:XX:XX:XX 01:35:36 dhclient: Sending on Socket/fallback 01:35:36 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:35:36 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX 01:35:36 dhclient: bound to XXX.XXX.XXX.XXX -- renewal in XXX seconds. 01:35:36 NetworkManager[XX40]: <info> (eth1): DHCPv4 state changed preinit -> reboot 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) started... 01:35:36 NetworkManager[XX40]: <info> address XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> prefix 20 (XXX.XXX.XXX.XXX) 01:35:36 NetworkManager[XX40]: <info> gateway XXX.XXX.XXX.XXX 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> nameserver 'XXX.XXX.XXX.XXX' 01:35:36 NetworkManager[XX40]: <info> domain name 'server.domain.tld' 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) scheduled... 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 4 of 5 (IP4 Configure Get) complete. 01:35:36 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) started... 01:35:37 NetworkManager[XX40]: <info> (eth1): device state change: 7 -> 8 (reason 0) 01:35:37 NetworkManager[XX40]: <info> (eth1): roamed from BSSID XX:XX:XX:XX:XX:XX (XXXXXXXXXX) to XX:XX:XX:XX:XX:XX (XXXXXXXXX) 01:35:37 NetworkManager[XX40]: <info> Policy set 'Auto XXXXXXXXXX' (eth1) as default for IPv4 routing and DNS. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) successful, device activated. 01:35:37 NetworkManager[XX40]: <info> Activation (eth1) Stage 5 of 5 (IP Configure Commit) complete. 01:35:43 wpa_supplicant[XX60]: Trying to associate with XX:XX:XX:XX:XX:XX (SSID='XXXXXXXXXX' freq=2412 MHz) 01:35:43 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> associating 01:35:43 wpa_supplicant[XX60]: Association request to the driver failed 01:35:46 wpa_supplicant[XX60]: Associated with XX:XX:XX:XX:XX:XX 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associating -> associated 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: associated -> 4-way handshake 01:35:46 wpa_supplicant[XX60]: WPA: Key negotiation completed with XX:XX:XX:XX:XX:XX [PTK=CCMP GTK=TKIP] 01:35:46 wpa_supplicant[XX60]: CTRL-EVENT-CONNECTED - Connection to XX:XX:XX:XX:XX:XX completed (reauth) [id=0 id_str=] 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: 4-way handshake -> group handshake 01:35:46 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:40:47 wpa_supplicant[XX60]: WPA: Group rekeying completed with XX:XX:XX:XX:XX:XX [GTK=TKIP] 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: completed -> group handshake 01:40:47 NetworkManager[XX40]: <info> (eth1): supplicant connection state: group handshake -> completed 01:50:19 dhclient: DHCPREQUEST of XXX.XXX.XXX.XXX on eth1 to XXX.XXX.XXX.XXX port 67 01:50:19 dhclient: DHCPACK of XXX.XXX.XXX.XXX from XXX.XXX.XXX.XXX

  Read the article

• MacBook Pro Late 2009 SATA Resets, Slowness

  - by A Student at a University

  My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. The resets correlate with AC power connects and disconnects. I don't know if the warnings do. (How do I tell?) Are these bus CRC errors? Or something else? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16 :[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16 :[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16 :[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16 :[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16 :[ 0.813473] scsi0 : ahci 02:37:16 :[ 0.823340] scsi1 : ahci 02:37:16 :[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16 :[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16 :[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16 :[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16 :[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.229570] ata2.00: configured for UDMA/133 02:37:16 :[ 1.240133] ata2: hard resetting link 02:37:16 :[ 1.260738] ata1.00: configured for UDMA/133 02:37:16 :[ 1.280122] ata1: hard resetting link 02:37:16 :[ 1.470125] usb 2-5: new high speed USB device using ehci_hcd and address 3 02:37:16 :[ 1.550165] firewire_core: created device fw0: GUID 58b035fffea99f5c, S800 02:37:16 :[ 1.631306] Initializing USB Mass Storage driver... 02:37:16 :[ 1.631392] scsi6 : usb-storage 2-5:1.0 02:37:16 :[ 1.631454] usbcore: registered new interface driver usb-storage 02:37:16 :[ 1.631455] USB Mass Storage support registered. 02:37:16 :[ 1.960128] usb 4-1: new full speed USB device using ohci_hcd and address 2 02:37:16 :[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.994215] ata2.00: configured for UDMA/133 02:37:16 :[ 1.994220] ata2: EH complete 02:37:16 :[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 2.090773] ata1.00: configured for UDMA/133 02:37:16 :[ 2.090778] ata1: EH complete 02:37:16 :[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16 :[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16 :[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16 :[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16 :[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16 :[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16 :[ 2.091337] sda: 02:37:16 :[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16 :[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16 :[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091756] sdb: sda1 sda2 02:37:16 :[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16 :[ 2.093505] sdb1 sdb2 sdb3 02:37:16 :[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16 :[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16 :[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16 :[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25 :[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25 :[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25 :[ 19.641533] ata1: hard resetting link 02:37:25 :[ 19.642084] ata2: hard resetting link 02:37:26 :[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.396697] ata2.00: configured for UDMA/133 02:37:26 :[ 20.396703] ata2: EH complete 02:37:26 :[ 20.451491] ata1.00: configured for UDMA/133 02:37:26 :[ 20.451498] ata1: EH complete 02:37:30 :[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30 :[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30 :[ 24.627246] ata1: hard resetting link 02:37:30 :[ 24.632250] ata2: hard resetting link 02:37:31 :[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.386782] ata2.00: configured for UDMA/133 02:37:31 :[ 25.386788] ata2: EH complete 02:37:31 :[ 25.431668] ata1.00: configured for UDMA/133 02:37:31 :[ 25.431674] ata1: EH complete 02:45:54 :[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55 :[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55 :[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622583] ata1: hard resetting link 02:45:55 :[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622624] ata2: hard resetting link 02:45:56 :[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.384305] ata2.00: configured for UDMA/133 02:45:56 :[ 530.384314] ata2: EH complete 02:45:56 :[ 530.399225] ata1.00: configured for UDMA/133 02:45:56 :[ 530.399233] ata1: EH complete 02:45:58 :[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58 :[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58 :[ 532.590983] ata1: hard resetting link 02:45:58 :[ 532.591045] ata2: hard resetting link 02:45:59 :[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.344416] ata2.00: configured for UDMA/133 02:45:59 :[ 533.344424] ata2: EH complete 02:45:59 :[ 533.360839] ata1.00: configured for UDMA/133 02:45:59 :[ 533.360847] ata1: EH complete 02:45:59 :[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59 :[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59 :[ 533.660132] ata2: hard resetting link 02:45:59 :[ 533.660151] ata1: hard resetting link 02:46:00 :[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.416768] ata2.00: configured for UDMA/133 02:46:00 :[ 534.416777] ata2: EH complete 02:46:00 :[ 534.431396] ata1.00: configured for UDMA/133 02:46:00 :[ 534.431401] ata1: EH complete 02:46:03 :[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03 :[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03 :[ 537.586002] ata1: hard resetting link 02:46:03 :[ 537.586036] ata2: hard resetting link 02:46:04 :[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.334389] ata2.00: configured for UDMA/133 02:46:04 :[ 538.334398] ata2: EH complete 02:46:04 :[ 538.343511] ata1.00: configured for UDMA/133 02:46:04 :[ 538.343519] ata1: EH complete 02:46:04 :[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04 :[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04 :[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540159] ata1: hard resetting link 02:46:04 :[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540220] ata2: hard resetting link 02:46:05 :[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.294100] ata2.00: configured for UDMA/100 02:46:05 :[ 539.294106] ata2: EH complete 02:46:05 :[ 539.314125] ata1.00: configured for UDMA/100 02:46:05 :[ 539.314132] ------------[ cut here ]------------ 02:46:05 :[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05 :[ 539.314144] Hardware name: MacBookPro5,3 02:46:05 :[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05 :[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05 :[ 539.314224] Call Trace: 02:46:05 :[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05 :[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05 :[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05 :[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05 :[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05 :[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05 :[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05 :[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05 :[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05 :[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05 :[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05 :[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05 :[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05 :[ 539.314296] ata1: EH complete 02:46:12 :[ 547.040117] ata1: hard resetting link 02:46:13 :[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13 :[ 547.408430] ata1.00: configured for UDMA/100 02:46:13 :[ 547.408438] ------------[ cut here ]------------ 02:46:13 :[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13 :[ 547.408451] Hardware name: MacBookPro5,3 02:46:13 :[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13 :[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13 :[ 547.408531] Call Trace: 02:46:13 :[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13 :[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13 :[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13 :[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13 :[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13 :[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13 :[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13 :[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13 :[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13 :[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13 :[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13 :[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13 :[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13 :[ 547.408620] ata1: EH complete 02:46:13 :[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13 :[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13 :[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13 :[ 547.738218] ata1: hard resetting link 02:46:13 :[ 547.738274] ata2: hard resetting link 02:46:14 :[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.486809] ata2.00: configured for UDMA/100 02:46:14 :[ 548.486818] ata2: EH complete 02:46:14 :[ 548.498998] ata1.00: configured for UDMA/33 02:46:14 :[ 548.499004] ata1: EH complete 02:46:18 :[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18 :[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18 :[ 552.529684] ata1: hard resetting link 02:46:18 :[ 552.529723] ata2: hard resetting link 02:46:19 :[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.284141] ata2.00: configured for UDMA/100 02:46:19 :[ 553.284150] ata2: EH complete 02:46:19 :[ 553.301629] ata1.00: configured for UDMA/33 02:46:19 :[ 553.301637] ata1: EH complete 02:46:21 :[ 556.078830] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:21 :[ 556.180361] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:22 :[ 556.262612] ata1: hard resetting link 02:46:22 :[ 556.262617] ata2: hard resetting link 02:46:22 :[ 557.010050] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.010070] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.014069] ata2.00: configured for UDMA/100 02:46:22 :[ 557.014075] ata2: EH complete 02:46:22 :[ 557.023646] ata1.00: configured for UDMA/33 02:46:22 :[ 557.023654] ata1: EH complete 02:46:30 :[ 565.047438] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:30 :[ 565.051554] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:30 :[ 565.108332] ata1: hard resetting link 02:46:30 :[ 565.108389] ata2.00: limiting speed to UDMA/33:PIO4 02:46:30 :[ 565.108406] ata2: hard resetting link 02:46:31 :[ 565.850048] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.850068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.854304] ata2.00: configured for UDMA/33 02:46:31 :[ 565.854313] ata2: EH complete 02:46:31 :[ 565.868477] ata1.00: configured for UDMA/33 02:46:31 :[ 565.868485] ata1: EH complete 02:46:35 :[ 569.265469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:35 :[ 569.268139] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:35 :[ 569.340079] ata1: hard resetting link 02:46:35 :[ 569.340113] ata2: hard resetting link 02:46:35 :[ 570.092568] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.092589] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.096828] ata2.00: configured for UDMA/33 02:46:35 :[ 570.096837] ata2: EH complete 02:46:35 :[ 570.110727] ata1.00: configured for UDMA/33 02:46:35 :[ 570.110735] ata1: EH complete 02:47:04 :[ 598.528232] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:47:04 :[ 598.653973] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:47:04 :[ 598.730854] ata1: hard resetting link 02:47:04 :[ 598.730910] ata2: hard resetting link 02:47:05 :[ 599.480136] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.480159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.484206] ata2.00: configured for UDMA/33 02:47:05 :[ 599.484213] ata2: EH complete 02:47:05 :[ 599.496699] ata1.00: configured for UDMA/33 02:47:05 :[ 599.496707] ata1: EH complete 04:45:59 :[ 7733.756548] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 04:45:59 :[ 7733.882748] EXT4-fs (dm-2): re-mounted. Opts: commit=0 04:45:59 :[ 7733.960142] ata1: hard resetting link 04:45:59 :[ 7733.960189] ata2: hard resetting link 04:46:00 :[ 7734.701926] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.719939] ata1.00: configured for UDMA/33 04:46:00 :[ 7734.719946] ata1: EH complete 04:46:00 :[ 7734.722547] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.726652] ata2.00: configured for UDMA/33 04:46:00 :[ 7734.726659] ata2: EH complete 04:46:02 :[ 7736.656465] ACPI: EC: GPE storm detected, transactions will use polling mode 13:38:49 :[39704.188621] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 13:38:49 :[39704.280588] EXT4-fs (dm-2): re-mounted. Opts: commit=600 13:38:49 :[39704.360819] ata1: hard resetting link 13:38:49 :[39704.360882] ata2: hard resetting link 13:38:50 :[39705.112956] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.114435] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.118673] ata2.00: configured for UDMA/33 13:38:50 :[39705.118682] ata2: EH complete 13:38:50 :[39705.127076] ata1.00: configured for UDMA/33 13:38:50 :[39705.127084] ata1: EH complete 13:39:49 :[39764.142463] applesmc: F1Mn: write arg fail 13:48:11 :[40267.025145] applesmc: FS! : read arg fail 13:52:53 :[40548.596735] applesmc: FS! : read arg fail 13:53:58 :[40613.972856] applesmc: FS! : read arg fail 13:54:08 :[40624.057339] applesmc: FS! : read arg fail 13:58:20 :[40875.397749] applesmc: TC0D: read data fail 14:16:56 :[41991.722054] applesmc: Th2H: read data fail 14:22:32 :[42327.991522] applesmc: light sensor data length set to 10 14:26:19 :[42554.788886] applesmc: F1Mn: write arg fail 14:32:36 :[42931.860443] applesmc: TC0F: read data fail 14:34:32 :[43048.041469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 14:34:33 :[43048.185850] EXT4-fs (dm-2): re-mounted. Opts: commit=0 14:34:33 :[43048.270184] ata1: hard resetting link 14:34:33 :[43048.270224] ata2: hard resetting link 14:34:33 :[43049.030049] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.030065] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.034106] ata2.00: configured for UDMA/33 14:34:33 :[43049.034112] ata2: EH complete 14:34:33 :[43049.056952] ata1.00: configured for UDMA/33 14:34:33 :[43049.056959] ------------[ cut here ]------------ 14:34:33 :[43049.056968] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:33 :[43049.056971] Hardware name: MacBookPro5,3 14:34:33 :[43049.056973] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:33 :[43049.057048] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:33 :[43049.057052] Call Trace: 14:34:33 :[43049.057060] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:33 :[43049.057064] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:33 :[43049.057069] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:33 :[43049.057074] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:33 :[43049.057083] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:33 :[43049.057088] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:33 :[43049.057093] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:33 :[43049.057097] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:33 :[43049.057102] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:33 :[43049.057107] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:33 :[43049.057111] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:33 :[43049.057115] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:33 :[43049.057118] ---[ end trace 76dbffc2d5d49d9d ]--- 14:34:33 :[43049.057123] ata1: EH complete 14:34:41 :[43057.012698] ata1: hard resetting link 14:34:42 :[43057.362780] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:42 :[43057.381432] ata1.00: configured for UDMA/33 14:34:42 :[43057.381441] ------------[ cut here ]------------ 14:34:42 :[43057.381450] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:42 :[43057.381453] Hardware name: MacBookPro5,3 14:34:42 :[43057.381455] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:42 :[43057.381530] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:42 :[43057.381533] Call Trace: 14:34:42 :[43057.381542] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:42 :[43057.381546] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:42 :[43057.381551] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:42 :[43057.381556] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:42 :[43057.381565] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:42 :[43057.381569] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:42 :[43057.381575] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:42 :[43057.381579] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:42 :[43057.381584] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:42 :[43057.381589] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:42 :[43057.381594] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:42 :[43057.381598] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:42 :[43057.381601] ---[ end trace 76dbffc2d5d49d9e ]--- 14:34:42 :[43057.381624] ata1: EH complete 14:34:42 :[43057.557887] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:42 :[43057.560517] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:42 :[43057.621194] ata1: hard resetting link 14:34:42 :[43057.621252] ata2: hard resetting link 14:34:43 :[43058.370141] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.370162] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.374407] ata2.00: configured for UDMA/33 14:34:43 :[43058.374415] ata2: EH complete 14:34:43 :[43058.381989] ata1.00: configured for UDMA/33 14:34:43 :[43058.381996] ata1: EH complete 14:34:43 :[43058.616228] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:43 :[43058.618931] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:43 :[43058.626687] ata1: hard resetting link 14:34:43 :[43058.626731] ata2: hard resetting link 14:34:44 :[43059.372908] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.372932] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.376997] ata2.00: configured for UDMA/33 14:34:44 :[43059.377003] ata2: EH complete 14:34:44 :[43059.392576] ata1.00: configured for UDMA/33 14:34:44 :[43059.392585] ata1: EH complete 15:48:19 :[47474.710860] ata1: hard resetting link 15:48:19 :[47474.710882] ata2: hard resetting link 15:48:20 :[47475.460144] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.460169] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.473709] ata1.00: configured for UDMA/33 15:48:20 :[47475.473717] ata1: EH complete 15:48:20 :[47475.727960] ata2.00: configured for UDMA/33 15:48:20 :[47475.727969] ata2: EH complete 16:29:39 :[49954.295017] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 16:29:39 :[49954.622307] EXT4-fs (dm-2): re-mounted. Opts: commit=0 16:29:39 :[49954.710139] ata1: hard resetting link 16:29:39 :[49954.710174] ata2: hard resetting link 16:29:40 :[49955.460046] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.460062] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.464138] ata2.00: configured for UDMA/33 16:29:40 :[49955.464144] ata2: EH complete 16:29:40 :[49955.473251] ata1.00: configured for UDMA/33 16:29:40 :[49955.473258] ata1: EH complete

  Read the article

• What is your definition of a programmer?

  - by Amir Rezaei

  The definition of a programmer is not obvious. It has happened that I have asked questions in this forum where people believe it don’t belong here because it’s not programmer related. I thought this question may clarify the definition. What characteristics, roles and activities do you think defines a programmer? Is there a typical programmer? The technology changes so fast that it may be hard to be typical programmer. From wikipedia: A programmer, computer programmer or coder is someone who writes computer software. The term computer programmer can refer to a specialist in one area of computer programming or to a generalist who writes code for many kinds of software. One who practices or professes a formal approach to programming may also be known as a programmer analyst. A programmer's primary computer language (C, C++, Java, Lisp, Delphi etc.) is often prefixed to the above titles, and those who work in a web environment often prefix their titles with web. The term programmer can be used to refer to a software developer, software engineer, computer scientist, or software analyst. However, members of these professions typically possess other software engineering skills, beyond programming; for this reason, the term programmer is sometimes considered an insulting or derogatory oversimplification of these other professions. This has sparked much debate amongst developers, analysts, computer scientists, programmers, and outsiders who continue to be puzzled at the subtle differences in these occupations

  Read the article

• Multiple home routers

  - by netvope

  Suppose I have the following configuration: Router A: WAN port connected to the Internet, LAN = 192.168.1.0/24 Computer A: Connected to router A as 192.168.1.101 Router B: WAN port connected to router A as 192.168.1.102, LAN = 192.168.2.0/24 Computer B: Connected to router B as 192.168.2.101 Now I want computer A to communicate with computer B seamlessly (e.g. can establish a TCP connection by running nc 192.168.2.101 <port>) by means of routing, rather than merging the two networks into one (which can be easily accomplished using router B as a switch). Most routers are shipped with NAT turned on, of which I definitely need to turn off in router B. But what other steps do I need to take so that packets from computer A to computer B would go through router B? I could manually add a routing table entry in computer A so that all packets targeted to 192.168.2.0/24 go through gateway 192.168.1.102, but I would prefer an automatic way if it exist.

  Read the article

• Multiple home routers

  - by netvope

  Suppose I have the following configuration: Router A: WAN port connected to the Internet, LAN = 192.168.1.0/24 Computer A: Connected to router A as 192.168.1.101 Router B: WAN port connected to router A as 192.168.1.102, LAN = 192.168.2.0/24 Computer B: Connected to router B as 192.168.2.101 Now I want computer A to communicate with computer B seamlessly (e.g. can establish a TCP connection by running nc 192.168.2.101 <port>) by means of routing, rather than merging the two networks into one (which can be easily accomplished using router B as a switch). Most routers are shipped with NAT turned on, of which I definitely need to turn off in router B. But what other steps do I need to take so that packets from computer A to computer B would go through router B? I could manually add a routing table entry in computer A so that all packets targeted to 192.168.2.0/24 go through gateway 192.168.1.102, but I would prefer an automatic way if it exist.

  Read the article

• windows 2003 domain and windows xp

  - by ryju

  I had to move a computer account from one OU to another OU for the settings to be same as with other computers in the OU. After the computer account was moved to other domain, i reset the computer account. Now there is no domain access to this computer even using domain admin acccount. The error message is that windows cannot connect to domain because your computer account was not found.I reset the computer account again and that didnt make any difference. Local admin access was possilbe and i tried to change the computer to workgroup to join back to domain, but workgroup changing option is greyed out. Is there any way I can solve this issue. Thanks in advance.

  Read the article

• 2 ATI Radeon HD 5870 (crossfire): Intermittent loud fan and non-functioning secondary card

  - by Merritt

  Installed 2 5870s. Left off the left side panel of my case(cooler master haf x), started my computer, installed the drivers and set up the crossfire... yada yada yada... everything worked fine. Then turned off computer, put left side panel back on, turned on computer, and heard a very loud buzzing (asssuming it was a gpu fan). Checked status of cards (in Windows 7) and the secondary card did not appear. Turned off the computer, took off left side panel, jiggled power connectors into secondary card, then turned the computer back on, and it worked again. Put the panel on, turned on computer, worked. Sometime later, turned on computer, and there's that loud fan sound again. What gives?

  Read the article

• Remote desktop connection

  - by mmh

  My work computer is running on Windows 7 Ultimate, and my home laptop is running on Windows 7 Home Premium. I want to connect my work computer from my home laptop, but whenever I try to do it gives me an error message saying: Remote desktop can't connect to the computer for one of the following reasons 1.Remote access to the server is not enabled. 2.The remote computer is turn off. 3.The remote computer is not available in the network. But when I tried to connect from my colleague's desktop I can connect to my computer. Please help me. I need to connect to my work computer from home.

  Read the article

• I need books for procedural programming

  - by Student

  Please suggest books for procedural programming. I need to know the core principles/patterns of procedural programming. So it doesn't matter if the book using any language to convey the procedural programming principles, be it pure C or others languages. Nowadays it is difficult to find ones. Even google and amazon searches didn't give me a satisfactory books. You may vote to close this question but please recommend books in comment section.

  Read the article

• Troubleshoot broken ZFS

  - by BBK

  I have one zpool called tank in RaidZ1 with 5x1TB SATA HDDs. I'm using Ubuntu Server 11.10 Oneric, kernel 3.0.0-15-server. Installed ZFS from ppa also I'm using zfs-auto-snapshot. The ZFS file system when zfs module loaded to the kernel hangs my computer. Before it I created few new file systems: zfs create -V 10G tank/iscsi1 zfs create -V 10G tank/iscsi2 zfs create -V 10G tank/iscsi3 I shared them through iSCSI by /dev/tank/iscsiX path. And my computer started to hanging sometimes when I used tank/iscsiX by iSCSI, do not know why exactly. I switched off iSCSI and started to remove this file systems: zfs destroy tank/iscsi3 I'm also using zfs-auto-snapshot so I had snapshots and without -r key my command not destroying the FS. So I issued next command: zfs destroy tank/iscsi3 -r The tank/iscsi3 FS was clean and contain nothing - it was destroyed without an issue. But tank/iscsi2 and tank/iscsi1 contained a lot of information. I tried zfs destroy tank/iscsi2 -r After some time my computer hang out. I rebooted computer. It didn't boot very fast, HDDs starts working like a crazy making a lot of noise, after 15 minutes HDDs stopped go crazy and OS booted at last. All seems to be ok - tank/iscsi2 was destroyed. After file systems at the tank was accessible, zpool status showed no corruption. I issued new command: zfs destroy tank/iscsi1 -r Situation was repeated - after some time my computer hang out. But this time ZFS seams not to healed itself. After computer switched on it started to work: loading scripts and kernel modules, after zfs starting to work it hanging my computer. I need to recover else ZFS file systems which lying in the same zpool. Few month ago I backup OS to flash drive. Booting from backed-up OS and import have the same results - OS starts hanging. How to recover my data at ZFS tank?

  Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >