Search Results

Search found 5859 results on 235 pages for 'driver'.

Page 101/235 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

• RHEL 5 SCSI ADPATEC

  - by Rajiv Sharma

  HI I have RHEL 5 box . and adpatec scsi card connected to it . I can see the adaptor under dsmeg | grep -i scsi dmesg | grep -i scsi SCSI subsystem initialized scsi0 : SCSI emulation for USB Mass Storage devices Type: CD-ROM ANSI SCSI revision: 00 scsi 0:0:0:0: Attached scsi generic sg0 type 5 sr0: scsi3-mmc drive: 0x/0x caddy sr 0:0:0:0: Attached scsi CD-ROM sr0 scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs Loading iSCSI transport class v2.0-871. iscsi: registered transport (iser) iscsi: registered transport (cxgb3i) Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.0 (Dec 06, 2009) iscsi: registered transport (bnx2i) scsi2 : Broadcom Offload iSCSI Initiator scsi3 : Broadcom Offload iSCSI Initiator iscsi: registered transport (tcp) iscsi: registered transport (be2iscsi) bnx2i: iSCSI not supported, dev=eth0 bnx2i: iSCSI not supported, dev=eth0 bnx2i: iSCSI not supported, dev=eth1 bnx2i: iSCSI not supported, dev=eth1 but cann't see under cat /proc/scsi/scsi cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: KVM Model: vmDisk-CD Rev: 0.01 Type: CD-ROM ANSI SCSI revision: 02 all st and sg modules are enable. Anyone please help me thanks advance Rajiv

  Read the article

• OSGI & Apache Commons-DBCP Classloading Issue

  - by Saul

  I inherited some code that is using the Apache commons-dbcp Connection pools in an OSGi bundle. This code works fine with Eclipse/Equinox OSGi version 3.4.3 (R34x_v20081215), commons-dbcp 1.2.2 and the postgres jdbc3 8.3.603 bundles from springsource.org. I wanted to modernize, maybe this was my first mistake! When I use the new version of Felix or Equinox OSGI Cores with the new postgresql JDBC3 or JDBC4 bundles along with the latest version of commons-dbcp (1.4.1), I am getting a classloading issue. I have done numerous searches and found that the commons-dbcp code should have a fix DBCP-214, but it still seems to fail. I have tried to put the org.postgresql on the commons-dbcp MANIFEST.MF import-package line, but that did not work either. I wrote a simple test in an activator that first does a basic class.forName() and DriverManager.getConnection(), this works fine, but when I add in BasicDataSource() and setup the connection with BasicDataSource.getConnection(), I get the ClassNotFoundException. See the code example below. Thanks in Advance for any help, suggestions, ... Sau! // This one fails with an exception public void dsTest() { BasicDataSource bds = new BasicDataSource(); ClassLoader cl; try { logger.debug("ContextClassLoader: {}", Thread.currentThread().getContextClassLoader().toString()); cl = this.getClass().getClassLoader(); logger.debug("ClassLoader: {}", cl); if (bds.getDriverClassLoader() != null) { logger.debug(bds.getDriverClassLoader().toString()); } // The failure is the same with and with the setDriverClassLoader() line bds.setDriverClassLoader(cl); bds.setDriverClassName("org.postgresql.Driver"); bds.setUrl("jdbc:postgresql://127.0.0.1/dbname"); bds.setUsername("user"); bds.setPassword("pword"); Class.forName("org.postgresql.Driver").newInstance(); conn = bds.getConnection(); Statement st = conn.createStatement(); ResultSet rs = st.executeQuery("SELECT COUNT(*) FROM table"); conn.close(); logger.debug("Closed DataSource Test"); } catch (Exception ex) { ex.printStackTrace(); logger.debug("Exception: {} ", ex.getMessage()); } } // This one works public void managerTest() { ClassLoader cl; try { cl = this.getClass().getClassLoader(); logger.debug("ClassLoader: {}", cl); Class.forName("org.postgresql.Driver").newInstance(); String url = "jdbc:postgresql://127.0.0.1/dbname"; conn = DriverManager.getConnection(url, "user", "pword"); Statement st = conn.createStatement(); ResultSet rs = st.executeQuery("SELECT COUNT(*) FROM table"); conn.close(); logger.debug("Closed Manger Test"); } catch (Exception ex) { ex.printStackTrace(); logger.debug("Exception: {} ", ex.getMessage()); } }

  Read the article

• Accessing one process's memory contents from another module

  - by Fangkai Yang

  I am developing a virtual device driver such that the user can write to the driver a process' pid and a virtual address, and the module will use these two values to get the memory contents of the target process. I am wondering if there is any easy functions that can fetch user page's data at this virtual address. I have tried get_user but this is not possible because the modules executing get_user at another process's context. I also tried to use ptrace_readdata, however, it seems that the file at /kernel/ptrace.c leaves a function access_process_vm undefined and also I don't know how to compile the source code of my module with this file (the linker seaches file in /linux/include by default). I am wondering if there are any other solutions...

  Read the article

• Best Practise for Writing a POS System

  - by Gary

  Hi, I'm putting together a basic POS system in C# that needs to print to a receipt printer and open a cash drawer. Do I have to use the Microsoft Point of Service SDK? I've been playing around with printing to my Samsung printer using the Windows driver that came with it, and it seems to work great. I assume though that other printers may not come with Windows drivers and then I would be stuck? Or would I be able to simply use the Generic/Text Driver to print to any printer that supports it? For the cash drawer I would need to send codes directly to the COM port which is fine with me, if it saves me the hassle of helping clients setup OPOS drivers on there systems. Am I going down the wrong path here? Thanks, Gary

  Read the article

• Update to php5.3 breaks connecting to mysql db

  - by bobbyb

  I just updated php to 5.3 and can no longer connect to my remote mysql server. I get the following errors: mysqli_connect(): OK packet 6 bytes shorter than expected mysqli_connect(): (HY000/2000): mysqlnd cannot connect to MySQL 4.1+ using old authentication It seems this has to do with the new mysqlnd driver. Is there a way to force it to use the old libmysql driver. Also, reverting to php5.2.11 doesn't seem to fix the issue which seems to work for most people. Anyone have any suggestions? thanks!

  Read the article

• LVDiff not working in Git

  - by Tanner

  I'm trying to get lvdiff from meta-diff suite to work with Git. My .gitconfig looks like this: [gui] recentrepo = C:/Users/Tanner/Desktop/FIRST 2010 Beta/Java/LoganRover [user] name = Tanner Smith email = [email protected] [merge "labview"] name = LabVIEW 3-Way Merge driver = 'C:/Program Files/National Instruments/Shared/LabVIEW Merge/LVMerge.exe' 'C:/Program Files/National Instruments/LabVIEW 8.6/LabVIEW.exe' %O %B %A %A recursive = binary [diff "lvdiff"] #command = 'C:/Program Files/meta-diff suite/lvdiff.exe' external = C:/Users/Tanner/Desktop/FIRST 2010 Beta/lvdiff.sh [core] autocrlf = true lvdiff.sh looks like this: #!/bin/sh "C:/Program Files/meta-diff suite/lvdiff.exe" "$2" "%5" | cat And my .gitattributes file looks like this: #Use a cusstom driver to merge LabVIEW files *.vi merge=labview #Use lvdiff as the externel diff program for LabVIEW files *.vi diff=lvdiff But everytime I do a diff, all Git returns is: diff --git a/Build DashBoard Data.vi b/Build DashBoard Data.vi index fd50547..662237f 100644 Binary files a/Build DashBoard Data.vi and b/Build DeashBoard Data.vi differ It is like it is not using it or even recognizing my changes. Any ideas?

  Read the article

• win7 amd64 guest in kvm does not have sound

  - by davidshen84

  hi, my host system is gentoo amd64, guest system is win 7 amd64. the guest system can work, except it does not have sound. i start kvm with -soundhw ac97, QEMU_AUDIO_DRV='alsa', and after i get into the guest system, i can see a 'Multimedia Audio Controller' in the device manager. but win7 cannot find the driver for it. i searched the network for a long time, and i cannot find a driver for intel ac97 for win7 amd64. i also tried -soundhw sb16, es1370, none of them work. please help me fix this.

  Read the article

• NpgSQL insert file path containing backslashes "\\"

  - by Chau

  I am trying to create a record containing the path to a file. The insertion is done into a Postgres database where UTF8 is enabled, using the NpqSQL driver. My table definition: CREATE TABLE images ( id serial, file_location character varying NOT NULL ) My SQL statement (boiled down to a minimum): INSERT INTO images (file_location) VALUES (E'\\2010') When using pgAdmin to insert the above statement, it works fine. Using the NpgSQL driver through Visual Studio C#, it fails with this exception: "ERROR: 22021: invalid byte sequence for encoding \"UTF8\": 0x81" Replacing my SQL statement with the following: INSERT INTO images (file_location) VALUES (E'\\a2010') ^ The E is encouraged by pgAdmin when using double backslashes. So a quick recap: Why is NpqSQL stopping my insertion of the \\2010?

  Read the article

• PHP Unlink function Woes on Windows

  - by Abs

  Hello all, I am having problems with the PHP function unlink. I keep getting this error: Warning: unlink(C:\wamp\www\webs\db\db_1276259188.mdb) [function.unlink]: Permission denied in C:\wamp\www\webs\pure-php-export.php on line 242 I am on a windows machine where Apache runs as the user SYSTEM. I have set the permissions of the db folder as "Full Control" for Apache's user. I thought my script might still be holding on to that file (its an uploaded file that gets used via PDO). try{ $dbh = new PDO("odbc:Driver={Microsoft Access Driver (*.mdb, *.accdb)};Dbq=$mdbFilename", $username, $password); }catch(PDOException $e){ echo $e->getMessage(); } So before I attempt to delete the file I unset the above and try to delete like so: $dbh = null; unset($dbh); if(is_file($mdbFilename)){ unlink($mdbFilename); } I really appreciate any help on this as it has been driving me mental for the past two hours! Thanks all for any help.

  Read the article

• Informix & .NET

  - by Giuliano

  I'm connecting to Informix 6.5 using the IBM OLE DB Driver. Some clarification: Informix Dynamic Server Workgroup Edition. Please note that there are many versions of IDS/WE - it helps to be precise about which version you have. It might be something like 10.00.TC1; the version number could be as old as 7.xx.TCx, or as new as 11.50.TCx. If your server is not on Windows but on Unix - or is on 64-bit Windows - the letter 'T' would change to 'U' (32-bit Unix) or 'F' (64-bit - Unix or Windows), or even 'H' (a particular HP-UX configuration). When I try to create a dataset using the VS DataSet wizard, after clicking on test connection it tells me 'Base Table not found'? The OLEDB driver is the official one provided by IBM. The problem with the 'Table not found' dialog is that Visual Studio doesn't tell me the table name but only the error! Has anyone else had this problem?

  Read the article

• DBD::Advantage and 64-bit Perl - Always 6060

  - by WarheadsSE

  I realize that I am attempting to go beyond the "supported" behavior of the manf's released drivers for perl, after all they have only released it in package with x86 .so's. However, since I cannot use their package with x64 Perl on a RHEL 5.4 x86_64 box, and maintaining a seperate install of x86 perl just for this one package, I have made an attempt to get this puppy working thanks to released 64-bit .so's that accompany other driver packages for Advantage. What I have done to this point: download beta 10 DBI drivers, in 32 download beta 10 PHP extension (it contains 32 and x86_64) copy the required DLLs into the ads-lib location (eg /usr/local/ads/lib64) compile the Perl DBI driver with the path to the lib64's .so's Good compilation, good install, good use. The problem is that I always get : failed: [iAnywhere Solutions][Advantage SQL][ASA] Error 6060: Advantage Database Server not available on specified server. axServerConnect (SQL-HY000)(DBD: db_login/SQLConnect err=-1) Does anyone have any ideas? EDIT: fixed package name in post title

  Read the article

• General ODBC Error in VBA

  - by raam

  Hi am populating the data from MS Access By Using VBA i am using below mentioned code.if i am run the same code in MS 2007 then It run properly but if i am run the same code in MS 2003 it gives the "General ODBC Error" how to solve this problem Any help would be appreciated!! Thanks in advance Sub Button2_Click() Dim varConnection As String Dim varSQL As String Dim cal, cal1, x varConnection = "ODBC; DSN=MS Access Database;DBQ=D:\Box\Generate.mdb;Driver={Driver do Microsoft Access (*.mdb)}" ' varSQL = "SELECT * FROM Empdata" With ActiveSheet.QueryTables.Add(Connection:=varConnection, Destination:=ActiveSheet.Range("C7")) .CommandText = varSQL .Name = "Query-39008" .Refresh BackgroundQuery = False End With End Sub

  Read the article

• Connect to Pick Database using Odbc C# .Net

  - by Badmate

  How to Connect to PickBasic database using Ole db driver .. I need it badly help me out

  Read the article

• Connect rails application to MsSQL 2005 from Windows

  - by Enrico Carlesso

  Hi guys. I (sadly) have to deploy a rails application on Windows XP which has to connect to Microsoft SQL Server 2005. Surfing in the web there are a lot of hits for connect from Linux to MsSQL, but cannot find out how to do it from Windows. Basically I followed these steps: Install dbi gem Install activerecord-sql-server-adapter gem My database.yml now looks like this: development: adapter: sqlserver mode: odbc dsn: test_dj host: HOSTNAME\SQLEXPRESS database: test_dj username: guest password: guest But I'm unable to connect it. When I run rake db:migrate I get IM002 (0) [Microsoft][ODBC Driver Manager] Data source name not found and no default driver specified I'm not a Windows user, so cannot understand really well the meaning of dsn element or so. Does someone have an idea how to solve this? Thanks in advance

  Read the article

• sqlserver 2008 and sql CE over Microsoft sync framework

  - by malik

  The server will drop the connection, because the client driver has sent multiple requests while the session is in single-user mode. This error occurs when a client sends a request to reset the connection while there are batches still running in the session, or when the client sends a request while the session is resetting a connection. Please contact the client driver vendor. Synchronisation process some time work and mostly fails. I have 5 client of sql CE that need to sync and i am using WCF IIS and sql 2008 for this process.

  Read the article

• EC2 instance suddenly refusing SSH connections and won't respond to ping

  - by Chris

  My instance was running fine and this morning I was able to access a Ruby on Rails app hosted on it. An hour later I suddenly wasn't able to access my site, my SSH connection attempts were refused and the server wasn't even responding to ping. I didn't change anything on my system during that hour and reboots aren't fixing it. I've never had any problems connecting or pinging the system before. Can someone please help? This is on my production system! OS: CentOS 5 AMI ID: ami-10b55379 Type: m1.small [] ~% ssh -v *****@meeteor.com OpenSSH_5.2p1, OpenSSL 0.9.8l 5 Nov 2009 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to meeteor.com [184.73.235.191] port 22. debug1: connect to address 184.73.235.191 port 22: Connection refused ssh: connect to host meeteor.com port 22: Connection refused [] ~% ping meeteor.com PING meeteor.com (184.73.235.191): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 ^C --- meeteor.com ping statistics --- 4 packets transmitted, 0 packets received, 100.0% packet loss [] ~% ========= System Log ========= Restarting system. Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled Built 1 zonelists Kernel command line: root=/dev/sda1 ro 4 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Xen reported: 2599.998 MHz processor. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Software IO TLB disabled vmalloc area: ee000000-f53fe000, maxmem 2d7fe000 Memory: 1718700k/1748992k available (1958k kernel code, 20948k reserved, 620k data, 144k init, 1003528k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5202.30 BogoMIPS (lpj=26011526) Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) Checking 'hlt' instruction... OK. Brought up 1 CPUs migration_cost=0 Grant table initialized NET: Registered protocol family 16 Brought up 1 CPUs xen_mem: Initialising balloon driver. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered i8042.c: No controller found. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Xen virtual console successfully installed as tty1 Event-channel device installed. netfront: Initialising virtual ethernet driver. mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 Registering block device major 8 IP route cache hash table entries: 65536 (order: 6, 262144 bytes) TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Using IPI No-Shortcut mode md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 144k freed *************************************************************** *************************************************************** ** WARNING: Currently emulating unsupported memory accesses ** ** in /lib/tls glibc libraries. The emulation is ** ** slow. To ensure full performance you should ** ** install a 'xen-friendly' (nosegneg) version of ** ** the library, or disable tls support by executing ** ** the following as root: ** ** mv /lib/tls /lib/tls.disabled ** ** Offending process: init (pid=1) ** *************************************************************** *************************************************************** Pausing... 5Pausing... 4Pausing... 3Pausing... 2Pausing... 1Continuing... INIT: version 2.86 booting Welcome to CentOS release 5.4 (Final) Press 'I' to enter interactive startup. Setting clock : Fri Oct 1 14:35:26 EDT 2010 [ OK ] Starting udev: [ OK ] Setting hostname localhost.localdomain: [ OK ] No devices found Setting up Logical Volume Management: [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda1 /dev/sda1: clean, 275424/1310720 files, 1161123/2621440 blocks [ OK ] Remounting root filesystem in read-write mode: [ OK ] Mounting local filesystems: [ OK ] Enabling local filesystem quotas: [ OK ] Enabling /etc/fstab swaps: [ OK ] INIT: Entering runlevel: 4 Entering non-interactive startup Starting background readahead: [ OK ] Applying ip6tables firewall rules: modprobe: FATAL: Module ip6_tables not found. ip6tables-restore v1.3.5: ip6tables-restore: unable to initializetable 'filter' Error occurred at line: 3 Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information. [FAILED] Applying iptables firewall rules: [ OK ] Loading additional iptables modules: ip_conntrack_netbios_ns [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... done. [ OK ] Starting auditd: [FAILED] Starting irqbalance: [ OK ] Starting portmap: [ OK ] FATAL: Module lockd not found. Starting NFS statd: [ OK ] Starting RPC idmapd: FATAL: Module sunrpc not found. FATAL: Error running install command for sunrpc Error: RPC MTAB does not exist. Starting system message bus: [ OK ] Starting Bluetooth services:[ OK ] [ OK ] Can't open RFCOMM control socket: Address family not supported by protocol Mounting other filesystems: [ OK ] Starting PC/SC smart card daemon (pcscd): [ OK ] Starting hidd: Can't open HIDP control socket: Address family not supported by protocol [FAILED] Starting autofs: Starting automount: automount: test mount forbidden or incorrect kernel protocol version, kernel protocol version 5.00 or above required. [FAILED] [FAILED] Starting sshd: [ OK ] Starting cups: [ OK ] Starting sendmail: [ OK ] Starting sm-client: [ OK ] Starting console mouse services: no console device found[FAILED] Starting crond: [ OK ] Starting xfs: [ OK ] Starting anacron: [ OK ] Starting atd: [ OK ] % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 390 100 390 0 0 58130 0 --:--:-- --:--:-- --:--:-- 58130 100 390 100 390 0 0 56984 0 --:--:-- --:--:-- --:--:-- 0 Starting yum-updatesd: [ OK ] Starting Avahi daemon... [ OK ] Starting HAL daemon: [ OK ] Starting OSSEC: [ OK ] Starting smartd: [ OK ] c CentOS release 5.4 (Final) Kernel 2.6.16-xenU on an i686 domU-12-31-39-00-C4-97 login: INIT: Id "2" respawning too fast: disabled for 5 minutes INIT: Id "3" respawning too fast: disabled for 5 minutes INIT: Id "4" respawning too fast: disabled for 5 minutes INIT: Id "5" respawning too fast: disabled for 5 minutes INIT: Id "6" respawning too fast: disabled for 5 minutes

  Read the article

• jQuery preventDefault stops rest of code working

  - by Tim

  I have this code where I am using jQuery to navigate to the next page, because I want some effects to take place before that happens. The problem is, that everything after the prevent.Default(); doesn't seem to work! $("a").click(function(event){ event.preventDefault(); $(".content-center").animate({height: "0px"}, 500); navigate($(this).attr('href')); }); I need things to happen in that order, so that the animation happens and once it's complete - load the next page... Does anyone have any ideas? Many thanks in advance? Tim Updated code (moves to new page but no animation occurs) --- $("a").click(function(event){ event.preventDefault(); var driver = $(this).attr('href'); $(".content-center").animate({ height: "0px" }, 500, function(){ navigate(driver); }); }); see: http://bit.ly/aOeYgE Many thanks for your help!!

  Read the article

• NFOP performance problem

  - by Jay Stevens

  We're using NFOP in a project (C#, ASP.NET 2.0) to ultimately return PDF files to the user. The process currently goes like this: Stored Procedure - XML XML - XSLT - XSL-FO XSL-FO - NFOP - PDF This works fine, the PDF is generated BEAUTIFULLY. The problem is that it takes 300+ seconds to do it. The ANTS profiler indicates that the problem is sitting in the driver.run() method inside of NFOP. It's not like this is a gargantuan amount of data, the size of the xsl-fo source going into the nfop driver object is ~980k. What's the most likely source and resolution of this problem? ANY hints or tips or answers are most appreciated, we were supposed to head to VA scan at 11 am. :|

  Read the article

• MySQLNonTransientConnectionException in jdbc program at run time

  - by Sunil Kumar Sahoo

  Hi I have created jdbc mysql connection. my program works fine for simple execution of query. But if i run the same program for more than 10 hour and execute query then i receives the following mysql exception. I have not used close() method anywhere. i created database connection and opened it forever and always execute query. there is no where that i explicitly mentioned timeout for connection. i am unable to identify the problem com.mysql.jdbc.exceptions.jdbc4.MySQLNonTransientConnectionException: Connection.close() has already been called. Invalid operation in this state. at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) com.mysql.jdbc.exceptions.jdbc4.MySQLNonTransientConnectionException: No operations allowed after statement closed. at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) sample code for database connection: String driver = PropertyReader.getDriver(); String url = dbURLPath; Class.forName(driver); connectToServerDB = DriverManager.getConnection(url); connectToServerDB.setAutoCommit(false);

  Read the article

• NamedParameterJdbcTemplate jconnect decimal issue

  - by user1052849

  I am using NamedParameterJdbcTemplate to insert data into a table. (Spring 2.5.3/Java 1.6) I am using jconnect driver to connect to sybase jdbc:sybase:Tds:<Server>:<Port>. For some reason the decimal values the decimal part is truncated. With the same code if I use jtds driver (jdbc:jtds:sybase://<Servername>:<Port>) its working fine. I cannot use jtds as jconn is being used by other code. In Java objects, field is defined as double. In database, field is defined as float (numeric with precision does not work). Any help is appreciated.

  Read the article

• zend framework 2 autentification using DbTable failure

  - by josepmra

  I have followed the zend instructions for implement my web Authentication using a database table. It's exactly the same code, but when render the page, the following exceptions appears: Zend\Authentication\Adapter\Exception\RuntimeException File: C:\xampp\htdocs\pfc\vendor\ZF2\library\Zend\Authentication\Adapter\DbTable.php Mensaje: The supplied parameters to DbTable failed to produce a valid sql statement, please check table and column names for validity. produced by this other: Zend\Db\Adapter\Exception\InvalidQueryException File: C:\xampp\htdocs\pfc\vendor\ZF2\library\Zend\Db\Adapter\Driver\Mysqli\Statement.php Mensaje: Statement couldn't be produced with sql: SELECT `users`.*, (CASE WHEN `password` = ? THEN 1 ELSE 0 END) AS `zend_auth_credential_match` FROM `users` WHERE `mail` = ? Seems to be that Statement.php can not execute the sql of above, but I send the sql by phpmyadmin replacing the ? for strings and work ok. I am sure that $dbAdapter works ok also because I have tested it and the columns name are "mail" and "password". This in my code, also I put the $dbAdapter test code. $dbAdapter = new DbAdapter(array( //This DbAdapter Work ok sure!! 'driver' => 'Mysqli', 'database' => 'securedraw', 'username' => 'root', 'password' => '' )); $fp = function($name) use ($dbAdapter) { return $dbAdapter->driver->formatParameterName($name);}; $sql = 'SELECT * FROM ' . $qi('users') . ' WHERE id = ' . $fp('id'); $statement = $dbAdapter->query($sql); $parameters = array('id' => 1); $sqlResult = $statement->execute($parameters); $row = $sqlResult->current(); $mail = $row['mail']; $password = $row['password']; //until here test $dbAdapter exitly!! //Start the auth proccess!! $authAdapter = new AuthDbTableAdapter($dbAdapter); $authAdapter->setTableName('users') ->setIdentityColumn('mail') ->setCredentialColumn('password'); $authAdapter->setIdentity('josep') ->setCredential('josep'); $authResult = $authAdapter->authenticate(); //This is the fail method!!!

  Read the article

• jQuery animation callback not working

  - by Tim

  Hey, if anyone could please help me then it would be much appreciated. Basically, I want to navigate to a new page once this animation has complete. Using the code below, the animation works fine but hen the navigation doesn't happen. Does anyone have any ideas or suggestions? Many thanks, Tim $("a").click(function(event){ event.preventDefault(); var driver = $(this).attr('href'); $(".content-center").animate({height: "0px"}, 500, function(){ navigate(driver); }); });

  Read the article

• can I see all SQL statements sent over an ODBC connection?

  - by Dave Cameron

  I'm working with a third-party application that uses ODBC to connect to, and alter, a database. During certain failure modes, the end-results are not what I expect. To understand it better, I'd like some way of inspecting all the statements sent to the database. Is there a way to do this with ODBC? I know with JDBC I could use http://www.p6spy.com/ to see all statements sent, for example when debugging hibernate. p6spy is a "proxy" driver that records commands sent and forwards them on to the real JDBC driver. Another possibility might be a protocol sniffer that would capture statements over the wire. Although, I'm unsure if ODBC includes a standard wire protocol, or only specifieds the API. Does anyone know of existing tools that would allow me to do either of these things? Alternatively, is there another approach I could take?

  Read the article

• Logictech USB HID controller message

  - by rross

  I have a Logitech game controller(http://www.amazon.com/Logitech-Dual-Action-Game-Pad/dp/B0000ALFCI). I'm using c# and Microsoft's HID driver to track what buttons are being pressed. Each button press sends a Byte Array that has 8 values. The problems is that I don't know what those 8 value represent. Here is an example: 0, 128, 126, 127, 130, 24, 24, 0, 4, 252 0, 128, 126, 127, 130, 40, 40, 0, 4, 252 0, 128, 126, 127, 127, 72, 72, 0, 4, 252 0, 128, 126, 127, 127, 136, 136, 0, 4, 252 Those are the values of the Byte Array for button press 1, 2, 3, 4 respectively. I see where the values are changing, but I'm unsure what they represent. I'm unable to find any specs on Microsoft HID driver. Can someone point me in the right direction?

  Read the article

• Problem with autocommit in ANT SQL task

  - by Alex Stamper

  I have an SQL script and want to apply it witn ANT task. This script clears out schema, creates new tables and views. The ANT defined task as follows: <sql driver="com.mysql.jdbc.Driver" url="jdbc:mysql://host:3306/smth" userid="smth" password="smth" expandProperties="false" autocommit="true" src="all.sql" > </sql> When this task launches, it shows in log that tables are cleared and created. But when it tries to create first view, it fails with: Failed to execute: CREATE VIEW component... AS SELECT component_raw.id AS MySQLSyntaxErrorException: Table 'component_raw' doesn't exist I have no idea why it fails here. Running this all.sql from MySQL query browser gives no errors. When I launched ANT with -v option, I didn't see any "COMMIT" messages.. Please, help to resolve the problem.

  Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >