Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 101/172 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

• CA and VPN setup

  - by Raj

  We are a small comany about 20 employees. We have some off site some i houser servers. Where should I install CA? On a domain controller or VM? can I obtain my own certificate for MS VPN? Where should I install MS vpn server? can I install on VM CA server? Do I need to open any ports on Firewall? Please send me or direct me to a web site where I can get setip by step installation instructions. Thanks.

  Read the article

• virtualbox ftp hangs on list command

  - by Tiddo

  Hi all, I have virtual box installed on a windows 7 64-bit computer, with Cent OS 5.5 as guest os. I want to be able to use ftp between those. I've installed vsftpd on the guest os, and the guest os uses a nat connection with the host os for internet. So far, I am able to connect to the guest os using ftp (in filezilla), but after the list command is executed, nothing happens, until the command is timed out. This happens in both active and passive mode. I do have set a pasv_min/max_port in the vsftpd.conf file, listing is enabled, and the ports are redirected in virtualbox. Also the ftp_data_port is set to 20. I also tried setting the pasv_address, but I had to set it to 127.0.0.1, but than filezilla gives me this: Command: PASV Response: 500 OOPS: bad family Command: PORT 127,0,0,1,139,204 Response: 500 OOPS: child died Can someone help me with this?

  Read the article

• Static Route Qestion

  - by mrlayance

  I have a Wan simulator between 2 networks. I can ping both networks from the wan simulator, but I can not ping from one network to the other. testr01 Fa0/0 10.0.0.1/24 FA0/1 192.168.0.1/30 | | Wan Sim 2 nics Eth0 192.168.0.2/30 | Eth1 192.168.1.2/30 | | testr02 Fa0/1 192.168.1.1/30 Fa0/0 10.1.0.2/24 I can not figure out what type of routes I need. On the route? On the Server? I guess all 10. traffic to the Fa0/0 ports? Thanks

  Read the article

• OSX Parallels 5 - can't share internet connection when using host-only networking...

  - by Steve Kirtley

  I've just upgraded from Parallels 3 to Parallels 5, but am having a problem matching my previous configuration. I am a web developer so run a local web server on my mac. I used to allow access to this from the virtual machines in Parallels by using 'Host-Only Networking' and then in OSX enabling internet sharing from my wifi/ethernet to the virtual ethernet ports that Parallels created. The setup was based on: http://www.craigfrancis.co.uk/features/setup/parallels/ The new version of Parallels doesn't create any network adaptors that are available for internet sharing in OSX - just VNIC's which only show under an ifconfig... Can anyone suggest how to make this all play nice? Thanks in advance! Steve

  Read the article

• Management VLAN Cisco Catalyst

  - by cha789

  I have configured a couple of VLANs on a Cisco Catalyst switch, i will put all the ports that clients is connected to, into these VLANs. I want to configure the native VLAN [vlan 1] as management VLAN so i can use a telnet client to connect to the switch. How can i block all but one specific IP-address to telnet into the switch? As i understand vlan 1 has many task regarding different protocols and i do not want to break that but only allow one specific IP-address to connect to the switch with a telnet client [actually the gateway ip address of the switch].

  Read the article

• PSAD Firewall/ UDP flood?

  - by Asad Moeen

  Well I'm actually trying to block a UDP Flood on the Application port because the string "getstatus" is causing my application to make large output due to a small input to the attacker's IP. I installed PSAD firewall to do the job. psad -S shows 3000,000 logged packets at the application port and top ports in Scan but does not block the IP of the attacker however other IP Addresses with small number of connections are dropped. I'm thinking that since output is also being made to the attacker, this is why its not getting blocked because iptables rate-limiting is also exactly doing the same thing and not blocking the IP where outgoing connection is also made. Any guesses why it won't work?

  Read the article

• ATI Radeon 5850 I cant seem to get 3 monitors up at the same time. 2 Monitors and a HDTV but still.

  - by Jan

  Ive just bought the top end ATI Radeon card with 2 normal monitor ports and a HDMI. The idea was to continue using my dual screen setup as always and to use the last plug, the HDMI on my TV. I got a new 52 inch HD TV with all the necessary bits. This should work fine. But.. in Display Properties I still get only my 2 monitors up as options. Not the Digital TV. When I unplug 1 monitor and restart the computer, I get the TV and the other monitor. But never all 3 at the same time. Why is this ? Where can I go to tell it that I need all 3 screens at the same time. Also I get a message saying my gfx card also gives sound through the HDMI cable.. But the TV tells me its recieving a sound format that it does not understand. Any ideas on that too while were at it ?

  Read the article

• Windows 2008 Routing and Remote access server - access to the internet

  - by Ian

  I have a windows 2008 r2 remote access server set up and running. The remote access works fine. My problem is that the remote access server itself doesn't have access to the internet. The box has two interfaces, an internal and an external. Inbound connections come in on the external interface and RRAS responds. All wall and nice. I want to be able to use windows update, browse, etc from this box but can't as the outbound traffic just gets blocked. I've tried going into the RRAS mmc tool and opening the interface properties, under which there are two buttons for inbound and outbound filters. There I tried adding ports 80 and 443, but this doesn't work completely. I can see the connection initiating (Syn goes out) but the session never establishes itself. Anyone done this or got any suggestions?

  Read the article

• Can't bring NAT to work

  - by user31738

  Hello, I bought a D-link DIR-300 wireless router and i can't bring NAT to work, i have an ssh and http service i need to forward to the internet. My connection is as follows: I have an ADSL connection, i'm using a ADSL ethernet modem connected and working, it doesnt let me put it on bridge mode. I have my router connected to my adsl modem through ethernet, it gets its ip through DHCP (and i'ts always the same) I have a desktop computer running linux with apache and openssh configured and working, it has fixed ip. I configured the NAT in the modem forwarding port 22 from the router ip to the internet. In the router i setup NAT forwarding port 22 from the desktop computer fixed ip to out there. This setup already worked with a fonera i had before, can anyone help me with this or tell me what kind of tests do i need to do? How can i test if the router is forwarding ports correctly before the modem?

  Read the article

• How to achieve reliable Gigabit Ethernet Link with my Acer Aspire Revo R3610?

  - by The Operator

  I want to stream HD movies over my wired Gigabit LAN from my PC to my Acer Aspire Revo R3610. It's connected with a 3ft Cat5e patch cable to my Netgear GS605v2 Switch. The PC acting as File Server is connected at 1Gbps to the Switch. Network driver options are set to defaults, including automatic speed/duplex negotiation on both machines. The Revo will not connect to my Network Switch at 1Gbps - the OS reports that it reverts to 100Mbps either shortly after connection or immediately upon connection. Through a process of elimination (trying different drivers, patch cables, ports on the switch, and other 1Gbps-capable devices connected to the Network switch which successfully achieve 1Gbps links and performance) I have drawn the conclusion there is either a Hardware or Software (Driver) issue with the Revo itself. I have performed tests using Windows 7 and Ubuntu 9.10. Can anyone offer insight on Gigabit Ethernet with the Revo?

  Read the article

• mystery Internet traffic to port 445

  - by Ben Collver

  Recently, I noticed traffic from the office network to TCP port 445 on the Internet [a]. Below are the Linux firewall log entries to Facebook's network [b] and Google's network [c]. I would like to identify the source of this traffic. My first guess is that Facebook and Google might be using multiple TCP ports for SSL load balancing. However, I could not confirm this based on the web proxy logs. What else might it be? [a] http://support.microsoft.com/kb/204279 [b] Sep 4 08:30:03 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.131 DST=69.171.237.34 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=14287 DF PROTO=TCP SPT=51711 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0 [c] Aug 28 06:02:41 firewall01 kernel: IN=eth0 OUT=eth2 SRC=10.0.0.115 DST=173.194.33.47 LEN=52 TOS=0x00 PREC=0x00 TTL=127 ID=4558 DF PROTO=TCP SPT=49294 DPT=445 WINDOW=8192 RES=0x00 SYN URGP=0

  Read the article

• AWS EC2: How to determine whether my EC2/scalr AMI was hacked? What to do to secure it?

  - by Niro

  I received notification from Amazon that my instance tried to hack another server. there was no additional information besides log dump: Original report: Destination IPs: Destination Ports: Destination URLs: Abuse Time: Sun May 16 10:13:00 UTC 2010 NTP: N Log Extract: External 184.xxx.yyy.zzz, 11.842.000 packets/300s (39.473 packets/s), 5 flows/300s (0 flows/s), 0,320 GByte/300s (8 MBit/s) (184.xxx.yyy.zzz is my instance ip) How can I tell whether someone has penetrated my instance? What are the steps I should take to make sure my instance is clean and safe to use? Is there some intrusion detection techinque or log that I can use? Any information is highly appreciated.

  Read the article

• Virtualmin Configuration

  - by Allen

  I am trying to get Virtualmin setup and have reached a point where my noobish sysadmin skills aren't getting the job done. This is the message I get now when I try and refresh the configuration of Virtualmin. BIND DNS server is installed, and the system is configured to use it. However, the default master DNS server XXXXXX is not a fully qualified domain name. Sendmail is only accepting SMTP connections on the following ports : 127.0.0.1 port smtp. Email from other systems on the Internet will not be accepted. This can be changed in the Sendmail Mail Server module. Please advise what I need to do to get Sendmail configured properly. Thanks!

  Read the article

• Connecting to local Sql server 2005 through Internet

  - by Manish

  Hello My Sql server is on Local Machine, I want to access it through Internet. I Configure Surace manager and Configuration manager of sqlserver 2005 for remote access. My sqlserver is running on port:1433 I am using port forwarding , I can access service of other ports, My Connetion String Is: Data Source=190.190.200.100,1433;Network Library=DBMSSOCN;Initial Catalog=myDataBase;User ID=myUsername;Password=myPassword; But it gives following error when i am trying to connect sql server through internet: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

  Read the article

• How to block own rpcap traffic where tshark is running?

  - by Pankaj Goyal

  Platform :- Fedora 13 32-bit machine RemoteMachine$ ./rpcapd -n ClientMachine$ tshark -w "filename" -i "any interface name" As soon as capture starts without any capture filter, thousands of packets get captured. Rpcapd binds to 2002 port by default and while establishing the connection it sends a randomly chosen port number to the client for further communication. Both client and server machines exchange tcp packets through randomly chosen ports. So, I cannot even specify the capture filter to block this rpcap related tcp traffic. Wireshark & tshark for Windows have an option "Do not capture own Rpcap Traffic" in Remote Settings in Edit Interface Dialog box. But there is no such option in tshark for linux. It will be also better if anyone can tell me how wireshark blocks rpcap traffic....

  Read the article

• PDAnet on Android IP on PC is not public IP. Where does the NAT take place, PDAnet or Verizon?

  - by lcbrevard

  When using PDAnet on a PC (Win7 ultimate) to USB tether a Motorola Droid on Verizon 3G the IP address of the PC appears to be public - 64.245.171.115 (64-245-171-115.pools.spcsdns.net) - but connections show as coming from another public IP - 97.14.69.212 (212-sub-97.14.69.myvzw.com). Someone is performing Network Address Translation - either PDAnet or within the Verizon 3G network. Can someone tell me who is doing the NAT? Is it PDAnet or is it at Verizon? Is there any possibility of setting up port forwarding, such that connections to the public IP 97.14.69.212 (212-sub-97.14.69.myvzw.com) are forward to the PC? We are testing a network protocol that requires either a true public IP or forwarding a range of ports from the public Internet to the system on which the software runs (actually Linux hosted by VMware Player or Workstation on a PC running Windows).

  Read the article

• 10 gigabit or 1 gigabit switch

  - by Guntis

  We are planning to move mysql to dedicated box. At this moment we have web servers and mysql is running on each. Question is: cheaper is to buy 10G switch and put 10G network card into mysql server. Or buy normal gigabit switch and connect mysql box to switch with multiple network cables. In 1G scenario then we give each web server different mysql IP address. I don't think, that mysql box with one 1G link is enough to to satisfy multiple web box mysql traffic. At this moment we have 3 servers witch are running mysql/web. Plan is to add fourth server for mysql only. Thanks. Edit: if we buy 1G switch with mini-GBIC ports. Can we put in mini-GBIC 10G connectors and then connect mysql box to that port?

  Read the article

• How do multiple displays work on a AMD 785G / ATI HD 4200 motherboard?

  - by aireq

  I just ordered a ASUS M4A785TD-V EVO which has the AMD 785G chipset and HD4200 integrated graphic. The board has VGA, DVI, and HDMI outputs. I'm wondering how many outputs I can run at once, and from what connectors? My guess is that I can only use the VGA, and either the DVI or the HDMI in a dual setup. But not the HDMI and the DVI at the same time. Is this correct? If I have devices plugged into both the HDMI and the DVI ports is there a way to choose between which port I want to use? I have a dual 19" monitor setup, as well as a LCD TV. I'd like to run the VGA and the DVI into my two monitors, and then the HDMI to my TV. Then when I want to watch something on the TV I'd like to be able to switch over from the DVI to the HDMI. Is this possible with out crawling under my desk and unplugging/plugging things in?

  Read the article

• Which iptables rule do you think is a 'must have'

  - by Saif Bechan

  I have some basic iptable rules set up now for my vps. Just block everything except some default ports, 80,21,22,443. I do get brute forced a lot. I have heard that iptables is very powerful but I have not seen many use cases. Can you give me an example of a(some) rule(s) you always use and give a small example why. I can not find a general best practice post here on SF, if there is any I would like the link. If this is a duplicate I am sorry and it can be closed.

  Read the article

• Suggestions for a SOHO/Home Asterisk system

  - by James

  I would like to buy a small embedded system that runs Linux and Asterisk. I would like two FXS ports ( to plug analogue phones into ) and one FXO port ( to plug in to my real line to allow access to the POTS ). I would like it to have a USB port to hold storage for voicemail. I really want it for home use so I would like it to be under £150 ( say $250 ), given that you can buy ADSL routers for around this much can any of them be made to run Linux and Asterisk? I don't want a PC as the power usage would be too high. I am looking for something like this ASDL router but open and able to run Asterisk or another open PBX. At worst I would like a box which had one FXO and two FXS and just made them completely available over IP to a full Asterisk system on a low power Atom system.

  Read the article

• Improving TCP performance over a gigabit network lots of connections and high traffic for storage and streaming services

  - by Linux Guy

  I have two servers, Both servers hardware Specification are Processor : Dual Processor RAM : over 128 G.B Hard disk : SSD Hard disk Outging Traffic bandwidth : 3 Gbps network cards speed : 10 Gbps Server A : for Encoding videos Server B : for storage videos andstream videos over web interface like youtube The inbound bandwidth between two servers is 10Gbps , the outbound bandwidth internet bandwidth is 500Mpbs Both servers using public ip addresses in public and private network Both servers transfer and connection on nginx port , and the server B used for streaming media , like youtube stream videos Both servers in same network , when i do ping from Server A to Server B i got high time latency above 1.0ms , the time range time=52.7 ms to time=215.7 ms - This is the output of iftop utility 353Mb 707Mb 1.04Gb 1.38Gb 1.73Gb mqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqqvqqqqqqqqqqqqqqqqqqqqqqqqqqq server.example.com => ip.address 6.36Mb 4.31Mb 1.66Mb <= 158Kb 94.8Kb 35.1Kb server.example.com => ip.address 1.23Mb 4.28Mb 1.12Mb <= 17.1Kb 83.5Kb 21.9Kb server.example.com => ip.address 395Kb 3.89Mb 1.07Mb <= 6.09Kb 109Kb 28.6Kb server.example.com => ip.address 4.55Mb 3.83Mb 1.04Mb <= 55.6Kb 45.4Kb 13.0Kb server.example.com => ip.address 649Kb 3.38Mb 1.47Mb <= 9.00Kb 38.7Kb 16.7Kb server.example.com => ip.address 5.00Mb 3.32Mb 1.80Mb <= 65.7Kb 55.1Kb 29.4Kb server.example.com => ip.address 387Kb 3.13Mb 1.06Mb <= 18.4Kb 39.9Kb 15.0Kb server.example.com => ip.address 3.27Mb 3.11Mb 1.01Mb <= 81.2Kb 64.5Kb 20.9Kb server.example.com => ip.address 1.75Mb 3.08Mb 2.72Mb <= 16.6Kb 35.6Kb 32.5Kb server.example.com => ip.address 1.75Mb 2.90Mb 2.79Mb <= 22.4Kb 32.6Kb 35.6Kb server.example.com => ip.address 3.03Mb 2.78Mb 1.82Mb <= 26.6Kb 27.4Kb 20.2Kb server.example.com => ip.address 2.26Mb 2.66Mb 1.36Mb <= 51.7Kb 49.1Kb 24.4Kb server.example.com => ip.address 586Kb 2.50Mb 1.03Mb <= 4.17Kb 26.1Kb 10.7Kb server.example.com => ip.address 2.42Mb 2.49Mb 2.44Mb <= 31.6Kb 29.7Kb 29.9Kb server.example.com => ip.address 2.41Mb 2.46Mb 2.41Mb <= 26.4Kb 24.5Kb 23.8Kb server.example.com => ip.address 2.37Mb 2.39Mb 2.40Mb <= 28.9Kb 27.0Kb 28.5Kb server.example.com => ip.address 525Kb 2.20Mb 1.05Mb <= 7.03Kb 26.0Kb 12.8Kb qqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqqq TX: cum: 102GB peak: 1.65Gb rates: 1.46Gb 1.44Gb 1.48Gb RX: 1.31GB 24.3Mb 19.5Mb 18.9Mb 20.0Mb TOTAL: 103GB 1.67Gb 1.48Gb 1.46Gb 1.50Gb I check the transfer speed using iperf utility From Server A to Server B # iperf -c 0.0.0.2 -p 8777 ------------------------------------------------------------ Client connecting to 0.0.0.2, TCP port 8777 TCP window size: 85.3 KByte (default) ------------------------------------------------------------ [ 3] local 0.0.0.1 port 38895 connected with 0.0.0.2 port 8777 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.8 sec 528 KBytes 399 Kbits/sec My Current Connections in Server B # netstat -an|grep ":8777"|awk '/tcp/ {print $6}'|sort -nr| uniq -c 2072 TIME_WAIT 28 SYN_RECV 1 LISTEN 189 LAST_ACK 139 FIN_WAIT2 373 FIN_WAIT1 3381 ESTABLISHED 34 CLOSING Server A Network Card Information Settings for eth0: Supported ports: [ TP ] Supported link modes: 100baseT/Full 1000baseT/Full 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 10000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 0 Transceiver: external Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes Server B Network Card Information Settings for eth2: Supported ports: [ FIBRE ] Supported link modes: 10000baseT/Full Supported pause frame use: No Supports auto-negotiation: No Advertised link modes: 10000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: No Speed: 10000Mb/s Duplex: Full Port: Direct Attach Copper PHYAD: 0 Transceiver: external Auto-negotiation: off Supports Wake-on: d Wake-on: d Current message level: 0x00000007 (7) drv probe link Link detected: yes ifconfig server A eth0 Link encap:Ethernet HWaddr 00:25:90:ED:9E:AA inet addr:0.0.0.1 Bcast:0.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1202795665 errors:0 dropped:64334 overruns:0 frame:0 TX packets:2313161968 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:893413096188 (832.0 GiB) TX bytes:3360949570454 (3.0 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2207544 errors:0 dropped:0 overruns:0 frame:0 TX packets:2207544 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:247769175 (236.2 MiB) TX bytes:247769175 (236.2 MiB) ifconfig Server B eth2 Link encap:Ethernet HWaddr 00:25:90:82:C4:FE inet addr:0.0.0.2 Bcast:0.0.0.2 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:39973046980 errors:0 dropped:1828387600 overruns:0 frame:0 TX packets:69618752480 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3013976063688 (2.7 TiB) TX bytes:102250230803933 (92.9 TiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:1049495 errors:0 dropped:0 overruns:0 frame:0 TX packets:1049495 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:129012422 (123.0 MiB) TX bytes:129012422 (123.0 MiB) Netstat -i on Server B # netstat -i Kernel Interface table Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg eth2 9000 0 42098629968 0 2131223717 0 73698797854 0 0 0 BMRU lo 65536 0 1077908 0 0 0 1077908 0 0 0 LRU I Turn up send/receive buffers on the network card to 2048 and problem still persist I increase the MTU for server A and problem still persist and i increase the MTU for server B for better connectivity and transfer speed but it couldn't transfer at all The problem is : as you can see from iperf utility, the transfer speed from server A to server B slow when i restart network service in server B the transfer in server A at full speed, after 2 minutes , it's getting slow How could i troubleshoot slow speed issue and fix it in server B ? Notice : if there any other commands i should execute in servers for more information, so it might help resolve the problem , let me know in comments

  Read the article

• connect to ssh server thru 80 via HTTP proxy?

  - by im_chc

  Hi, Please help: I want to connect to my ssh server at home However, I'm behind a corporate (CORP) firewall, which blocks almost all ports (443, 22, 23 etc). But it seems that 80 is not blocked, coz I am able to surf the web after I login (i.e. IE sets to CORP's proxy server, and start IE - displayed CORP intranet portal - type in google.com - dialog pops up for userid + pwd - login successful, and surf without restrictions) My ssh server listens at 443. My question is: Is there a way to connect from a computer behind the CORP firewall to the ssh server thru the 80 port, with the ssh server still listening on port 443? Changing the ssh server to listen to port 80 is not an option, coz my home ISP blocks 80. Can I use a public proxy which listens at 80? After some research on google I found that there is something called "connect to SSH thru an HTTP proxy" using the Cockscrew software. Is it useful? Or is there some other way to solve the problem?

  Read the article

• How to Use 3 Monitors

  - by The.Anti.9

  Right now my setup has a nice big 24" flatscreen in the center, and a 19" flatscreen to the left. And a big gaping hole on the right. I have a 3rd monitor to put there, but I'm not sure how to get the computer to recognize it. Do I need a graphics card with 3 ports? Or can I span the monitors over non SLI-Linked graphics cards? Is it possible to plug my 3rd monitor into the on-board VGA port and have it work?

  Read the article

• Windows Server 2003 not automatically assigning drive letter to external drives

  - by Chris

  My newly rebuilt Windows Server 2003 doesn't automatically assign drive letters to external usb devices. I have to manually open the Disk Management Console and assign it a drive letter every time. It does this with two different drives in all USB ports. I have been doing some reading and I don't have any network drives, I have also already tried USBDLM and it doesn't seem to have made any difference. Specs: ProLiant ML150 G5 with Windows 2003 Enterprise and all updates installed. Any ideas on what I can try to resolve this problem would be greatly appreciated. Chris

  Read the article

• Configuring vsftpd with nginx on ubuntu

  - by arby

  I have vsftpd installed on Ubuntu 12.04LTS along with nginx, php, and sql on an Amazon ec2 instance. The web server is good to go, but I'm having trouble connecting to the FTP server. I'm not quite sure how to set the privileges or what configuration options I might be missing. By default, the location of the web root is at /usr/share/nginx/www and it is owned by root:root. The web server runs as user www-data in the group www-data. I've opened port 21 and set the passive ports in the ec2 backend and ufw firewall. In vsftpd.conf, I have: ... anonymous_enable=NO local_enable=YES local_umask=0027 chroot_local_user=YES pasv_enable=YES pas_max_port=12100 pasv_min_port=12000 port_enable=YES ... Now, I'm unsure how to create the FTP user that when I login, displays my web directory with write access. I've tried it a few different ways, but I keep running into errors (either no connection, no write access, or very slow timeouts.)

  Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >