Search Results

Search found 8656 results on 347 pages for 'boot to vhd'.

Page 102/347 | < Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >

  • Power cycles on/off 3 times before booting properly from cold start, no other issues (New System)

    - by James
    Relevant Specs: Sapphire 5850, core i7 920, Seasonic x750 power supply, ECS X58B-A2 mobo. From a cold boot, meaning all power totally disconnected at the wall, the system will power on for less than a second and then power off completely. After two seconds of being powered off this will repeat and on the third "attempt" the computer will boot. To be very specific here is what happens: The power is turned on at the wall and on the psu, the orange stdby LED on the mobo is illuminated but the system is 'off'. I hit the power button on the case or on the mobo itself I hear the relay (?) in the psu closing The case light comes on and the mobo power light comes on. The fans start rotating. Immediately after this the I hear some relay click - the power lights extinguish, the fans stop, the stdby light remains on. Less than 2 seconds pass and the cycle repeats without any intervention from me. On the third attempt it boots normally and the machine runs perfectly. If I do a soft reboot or a full shutdown the computer starts normally the next time. It's only if I pull the power cord or flick the switch off on the PSU that I get the cycling again. Basically any time the stdby light on the mobo goes out. I have removed the graphics card and I get the same problem. I have removed the PSU, hotwired it to the ON position and verified voltages on all lines. The relay does not cycle when I do this. If I connect only the 24 pin ATX connector to the mobo and not the 8 pin ATX12V / CPU connector then I will not get the cycling, the fans run, the power light stays on, but obviously the system can't boot. Disconnecting all fans has no effect on the problem. My feeling it that it's something to do with the motherboard like a capacitor that's taking a long time to charge because it's leaking or something along those lines. But I can't imagine what could be 'wrong' with it and only manifest itself as a problem under these very specific circumstances. Any ideas? Thanks.

    Read the article

  • inaccessible_boot_device after p2v Windows 2000 Pro SP4 to Workstation 6.5

    - by 20th Century Boy
    I am using the latest VMware Converter Standalone to p2v a physical Windows 2000 Professional SP4 PC. The PC is a standard Pentium with IDE disk from circa 2001. The disk is 20GB partitioned logically into C: and D. It converts with no errors (I did both disks into one VMDK). When I power on the VM in VMware Workstation 6.5 (or Vmware Player 2.5) it gets to the Win 2000 boot graphic then I get a BSOD with the classic 0x7B Stop error: inaccessible_boot_device. Is there anything I can do to get the vm to boot? I am lost for ideas, normally p2v of a basic IDE pc works flawlessly. I'm willing to put a bounty on this as I am trying to sort this out for a client urgently.

    Read the article

  • Weird video problem with Linux variants

    - by alex
    I decided recently I wanted to give Linux a go so I first download a Ubuntu boot CD. The boot menu came up fine, and then a glowing Ubuntu logo was in the middle of the screen for a while. Then the screen was flickering orange and black. I guess this is where the GUI should of came up. Pushing Ctrl+Alt+F1 brought me to the command prompt OK. I thought this may have something to do with Ubuntu, so I downloaded Linux Mint. The same sort of thing happened. It booted fine, displayed it's logo for a while and then flickered, only green and black this time. Does this sound like a video card problem? How can I resolve this? Many thanks

    Read the article

  • Windows boots to Black Screen of Death — Is my HDD faulty?

    - by Flynn1179
    My wife's PC suddenly stopped booting up properly. It gets as far as the Windows 'loading' screen with the bar scrolling away, but that's as far as it gets for some time, then suddenly flashes up a BSoD barely long enough to see, then the display cuts out. We've got identical PCs, and after swapping components, I established that my PC suffers the same problem if I swap in the HDD. Even if I plug hers in as a second HDD on my machine, it still does the same thing, even though it's booting from mine. I can't even boot her machine from CD or DVD either, so I couldn't even use a recovery disc. I did manage to partially boot my PC into safe mode with the other HDD attached, and it got as far as loading 'crcdisk.sys' and froze. Anybody know what could be wrong with it, or at least how I can get the data off the disk? I'm assuming there's still data on the disk, given that it at least shows me the vista 'loading' screen.

    Read the article

  • udev: waiting for uevents to be processed on my Gentoo

    - by stan31337
    During the startup I see machine executing this thing for about 30 seconds: udev: waiting for uevents to be processed Then I get a quick message which says something like: devfs: timeout (50 seconds) I can't see the whole thing because after that system starts up very fast including Xfce. What logs and configs do I need to provide for further investigation? $uname -a Linux genta 3.6.6-gentoo #1 SMP Sun Nov 11 11:02:23 NOVT 2012 i686 Genuine Intel(R) CPU T2300 @ 1.66GHz GenuineIntel GNU/Linux Thank you! UPD: rc-status genta / # rc-status sysinit Runlevel: sysinit dmesg [ started ] udev [ started ] devfs [ started ] genta / # rc-status boot Runlevel: boot hwclock [ started ] modules [ started ] fsck [ started ] root [ started ] mtab [ started ] localmount [ started ] sysctl [ started ] bootmisc [ started ] hostname [ started ] termencoding [ started ] keymaps [ started ] net.lo [ started ] swap [ started ] urandom [ started ] procfs [ started ]

    Read the article

  • How to make a pxe bootable 10MegaByte or larger dos image?

    - by rjt
    Would like to make a "massive" DOS floppy disk image, say 10MegaBytes or more containing all the firmware updates i need for any system, harddrive, BIOS. i do not need the DOS image to be networkable as everything will be on the PXE booted image, but networking would be nice. Since ZipDisks were attached to the floppy disk controller and were over 100MegaBytes, this should be possible. i tried a long time ago to do this and spent too much time on it only to have it fail to boot. So if someone has reliable instructions on how to create such a nightmarish beast and edit it, please let me know. One image that can used for PXE and copied to a USB stick would be a plus. Too bad manufacturers don't supply a single bootable Linux ISO containing all their firmware updates, that would be easy to boot over-the-lan and have networking. HP servers do this and it is awesome.

    Read the article

  • Workaround for starting zabbix agent on Ubuntu. update-rc.d LSB mismatch

    - by bryan kennedy
    I am trying to run the zabbix-agent (1.8.1) on boot on Ubuntu (lucid 10.04). Zabbix is installed just fine, and it manually starts just fine with /etc/init.d/zabbix-agent start However it doesn't start on boot, because when I run: sudo update-rc.d zabbix-agent default I get: update-rc.d: warning: zabbix-agent start runlevel arguments (none) do not match LSB Default-Start values (2 3 4 5) update-rc.d: warning: zabbix-agent stop runlevel arguments (none) do not match LSB Default-Stop values (0 1 6) After googling around I found some cryptic information about this being a possible bug with Zabbix's startup scripts, but I can't find a workaround. I'm trying to understand how the update-rc.d system works, but I'm not getting very far. How can I modify this setup to start the zabbix-agent on startup?

    Read the article

  • Windows 7 EFI Partition Deleted

    - by Sam Clark
    I converted my Windows 7 GPT disk to dynamic, which resulted in it being unable to boot. So I used EaseUs Partition Master on my second Win 7 installation to convert the disk back to basic. Now, I have one partition, which is my C: drive, and I can't figure out how to recovery my EFI partition. I no longer see the "Windows" entry in my EFI boot menu. The Windows 7 repair on the install DVD doesn't see my installation. Please let me know how to restore the EFI partition.

    Read the article

  • Is the motherboard the cause of these errors?

    - by ianfuture
    Motherboard is : ASUS A7N8X-E Deluxe, Rev1.01, On start up get: "cmos checksum error - defaults loaded" error BIOS is reset everytime and can't boot to Windows off HDD. POST report is ok once I tell it there is no Floppy drive attached and not to seek it. The boot sequence starts then just as get to load windows safe mode options whole PC shuts down. BIOS is reset to defaults again. I've checked the battery and jumpers. Tried a known working battery. Changed Graphics card, changed memory, changed HD to one without an OS. Disconnected DVD drive. PSU is known to be ok. IN BIOS CPU is recognised correctly and memory is also recognised ok. So is it likely to be a bad motherboard or corrupted BIOS or something else? Thanks :)

    Read the article

  • Freezing with black screen after booting OS with AMD Catalyst driver

    - by Oleg
    I have ATI Mobility Radeon HD 5470 on my HP laptop. A few weeks ago I was confused with a weird trouble in proprietary drivers for my graphics card. When I start X server (or just boot Windows) system sometimes totally hangs up with black screen. The most annoying thing is that issue appearing is absolutely random (2 success, 3 fails, 1 success, 7 fails, etc.). It appears both on Linux (Arch, Debian 7) and Windows XP. I've tried reinstalling OS, drivers, etc. I've also tried updating BIOS. Then boot was successful for the next few times and issue appeared again (probably it was just a coincidence, because another BIOS updates gave no results). I really don't know what to do. Any ideas?

    Read the article

  • Mac Air Bootcamp Windows 7 Installation and USB3 Hurdles

    - by Casey
    I am trying to load windows 7 on a new Mac Air(OS X 10.9 Mavericks) using Boot camp, a downloaded windows 7 iso file, and USB3 flash drive. No obvious issues with stepping through the initial phases of boot camp and disc partition, but when the system reboots to load windows setup/install from the USB3 flash, it stalls after a few screens and gives a "missing cd/dvd drive" error. I have read similar posts regarding this fail that imply there is possibly a windows 7 compatibility concern with USB3, and that if a USB2 port is available....or if you can change your BIOS to make your USB3 look like USB2...then you can get around this error. Unfortunately I only have USB3 ports on this system, and it appears accessing the PC equivalent "BIOS" on the new Macs is very difficult....and if you screw it up you can ruin the system. Does anyone have any suggestions? I should also mention that there is NOT a CD/DVD drive on the Mac Air....and I can't migrate to Windows8 (for various reasons). Any help is much appreciated!!

    Read the article

  • DVD ROM is not working

    - by Cyril N.
    (note: I don't know in which StackExchange site to put this question, I'll thank the moderator that will move it to a more appropriate place, if there is a S.E. available for my question). I have a DVD RW drive that is well listed in the bios, and if no CD is in, it is also present in the "My Computer" of my Fedora 16. But when I put a disc on it, the icon disapear from "My Computer", and I can not do anything with this ! (Like erasing a RW disc). I'd like to boot a Fedora 17 Live CD image. I burned it on an other computer but when I try to run it in bios, nothing is done and I'm redirected to Grub of my HD. The command cdrecord -scanbus shows this : wodim: Warning: controller returns wrong size for CD capabilities page. wodim: Cannot get CD capabilities data. 6,1,0 601) 'HD-DT%ST' 'DVD%RAM G@22NP20' '1&04' Removable CD-ROM And when I try to mount manually the disc, I got this error : mount: block device /dev/sr0 is write-protected, mounting read-only mount: /dev/sr0: can't read superblock Here's a paste of dmesg | grep sr0 : [ 5.161265] sr0: scsi-1 drive [ 5.161621] sr 6:0:1:0: Attached scsi CD-ROM sr0 [ 834.545978] sr0: Hmm, seems the drive doesn't support multisession CD's [ 841.731194] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 842.021640] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 842.021652] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 842.021662] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 842.021672] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 [ 842.021688] end_request: I/O error, dev sr0, sector 0 [ 842.021697] Buffer I/O error on device sr0, logical block 0 [ 842.023715] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 843.048203] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 843.048211] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 843.048219] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 [ 843.048234] end_request: I/O error, dev sr0, sector 0 [ 843.048274] EXT4-fs (sr0): unable to read superblock [ 843.063155] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 843.075904] sr0: CDROM (ioctl) error, command: Get configuration 46 00 00 00 00 00 00 00 20 00 [ 843.220512] sr 6:0:1:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [ 843.220522] sr 6:0:1:0: [sr0] Sense Key : Aborted Command [current] [ 843.220530] sr 6:0:1:0: [sr0] Add. Sense: No additional sense information [ 843.220538] sr 6:0:1:0: [sr0] CDB: Read(10): 28 00 00 00 00 00 00 00 01 00 [ 843.220553] end_request: I/O error, dev sr0, sector 0 [ 843.220609] FAT-fs (sr0): unable to read boot sector The lines from Sense Key .. (line 6) to DRIVER_SENSE (line 11) are repeating a lot. I then changed my DVD player with an other spare one I had, and the disc didn't boot neither. I then changed the IDE cable, but still no success. What can I do to make it work? Thanks for your help.

    Read the article

  • Computer cannot detect hard disk

    - by Nrew
    Details: BIOS: AMI Bios, set primary master to Auto OS: Windows XP Sp2 Memory: 384 Mb Processor: Pentium 3 yeah this one is really very old. And some of the capacitors in the motherboard are already bulging. It detected the hdd yesterday when were trying to fix it and install xp. But today it cannot boot and said: Boot failure. What can you suggest that I would do to revive this old machine. What would be the problem, is it the hdd, the ide cable or the motherboard.

    Read the article

  • HP proliant dl360 g5 fails to reboot

    - by user1039384
    Some history of this also available here. As of my latest update on the forum linked above, now cold reboot as well as hard reset and following boot for my proliant dl360 g5 works as expected and successfully boot the system. However, soft-reboot results in internal health indicator turning RED on the front and long beeps every around 6seconds until I either cold reboot or press and hold the power button. A summary of system state when this happens: Internal Health led indicator: RED External Health led indicator: Green No led next to any component is red or amber No POST message neither on the video output nor on IML logs (verified both at the time issue occures and after cold reboot that boots the system successfully). Any thoughts please share. I hope we can knock this issue down together with your help!

    Read the article

  • How can I create an encrypted, bootable thumbdrive containing Linux?

    - by Hanno Fietz
    I want to have a bootable flash drive that's fully encrypted. I have not tested, but seem to like, TrueCrypt, which provides a fully encrypted system and has lots of other features I like (for instance, hidden volumes). Unfortunately, it seems, system encryption is only supported for Windows, although I'm not sure why. The crux here, I guess, is that you need a boot loader that is capable of asking for your password and decrypt the disk, at least the part that contains kernel and initrd. An alternative might be to have an unencrypted boot partition containing a more powerful system which will decrypt and mount the main partition. However, this brings up the question of whether you're introducing data leaks. Depending on the specific scenario, I may lack the experience to assess if this is a problem. So I'd strongly prefer a fully encrypted disk or a similarly straightforward alternative.

    Read the article

  • How to install OSX into VirtualBox on a Macbook Air using Apple's Reinstall USB

    - by eug
    I'm currently dual-booting OSX and Ubuntu on my Macbook Air, but it'd be nice to run OSX within Ubuntu via VirtualBox. This seems possible using VirtualBox and is legal - there's even a post on an Oracle blog describing this: http://blogs.oracle.com/karim/entry/installing_mac_os_x_in. Actually, I've read elsewhere that it's only legal with OSX Server, but can't find a reason why it'd be illegal with normal OSX - please let me know if you think otherwise. The problem I have is that a MacBook Air doesn't come with a bootable DVD, but with a "Reinstall Drive" which is a USB stick that comes up as a CDROM drive. It doesn't seem to be ISO9660-formatted though but has an Apple partition table, with OSX installed on an HFS partition. refit says that it has a "boot.efi" as well. I don't know Apple booting/partitioning very well and would really appreciate some advice on how to convert this USB into an ISO or boot it in VirtualBox some other way.

    Read the article

  • install grub on disk image

    - by Dima
    I have disk image with 2 partitions: Partition 1 has cramfs file system (read only). This partition contains all system files of the OS Partition 2 has ext3 file system. This partition has only configuration files that may be changed. How can I install GRUB1 boot loader on MBR. I tried to copy first 446 bytes of my hard disk and copy GRUB files to the /boot directory on the 1st (cramfs) partition. I cannot use grub-install because I have disk image and not disk itself. Any ideas?

    Read the article

  • Wake up and record in Windows Media Center on a Mac Mini

    - by Sir Code-A-Lot
    I'm currently considering buying a Mac Mini to use as a media center. I plan to install Windows 7 (or 8) on it, using Boot Camp. Will it be able to go into standby or hibernate (S3, S4?) and wake up to record TV scheduled in Windows Media Center? I haven't been able to find concrete information on supported standby types when running Windows under boot camp, and if Windows will even be able to wake when a recording should start. I just want to be clear on any limitations in this area before I buy anything.

    Read the article

  • How to create an UEFI bootable USB stick from an ISO

    - by shiin
    I have an ISO image of my backup solution's recovery cd. When I burn the image to a CD-ROM, I can boot from it in UEFI or normal mode without problems. Unfortunately, this is no solution for my laptop, as it does not have an optical drive. Thus, I tried to create a bootable USB stick that can also boot in UEFI mode, but so far I have not been successful (note that the laptop has UEFI and boots Windows 7 in UEFI mode). So my question is, if anyone knows how I can get said ISO on my USB stick so that it boots as if I would use a CD-ROM?

    Read the article

  • How can I make Windows XP bootable again?

    - by Scott Severance
    Some time ago, I replaced my hard drive. Foolishly, I imaged the individual partitions, not the entire drive. That meant that my system was unbootable. For my primary OS (Linux), that was no problem as I could simply re-run GRUB. However Windows XP remains unbootable. The machine in question is a netbook which doesn't have a CD drive or a restore partition, so I can't boot from a Windows CD and run fixmbr. How can I fix Windows? Here's a picture of what I see when I try to boot Windows from the GRUB menu: I don't actually have an XP CD, since of my two machines, the netbook in question has neither a restore partition nor a CD, and my other XP machine only came with a restore partition. So I'll also need a way to get hold of the necessary files.

    Read the article

  • Issue with Toshiba Satellite C50 A-1JM

    - by Nathan Hawkes
    I am having some odd problems with my Toshiba laptop. For the last two days, it has not loaded past the boot screen for hours, if at all. When I force the laptop off and switch it back on, it goes to the Preparing Automatic Repair process but will not complete the process and go to the desktop. However, this only happens when the battery is plugged in. When I remove the battery and run the laptop on power, it works without issue. Would this be a battery issue (given it works without the battery) or a hard drive issue (given it won't get past the boot screen)? If neither, what would you suggest as a solution?

    Read the article

  • PC boots on then off & 30 sec. later on again, it wiil shut off on itself mostly in idle or just unexpecticly

    - by Jody
    This problem started w/ my sons desktop, it would just shut off after a bit of work or stay on for a long time & to get it to unfreeze is to cold boot it, i put a new HDD in & I still have the same issue, RAM is good power supply fan is moving quite as well as all the rest of the fans it has stayed fairly dust free, i'm at a loss ,I have defaulted all the factory settings changed battery & ungraded to a new OS. I still have the same problem. the power light stays on after it has shut down & when upon starting it goes straight to safe mode option page, I start in last good config. reboots again takes 30 sec. to boot & will work again for a while, the only other thing I haven't tried was a graphic card replace, i'm onboard video now & have been.

    Read the article

  • How to tell which physical disks have bootable MBR?

    - by Jon
    The computer I am using right now has 6 physical disks attached. Using the BIOS's "select boot device" functionality I have discovered that I can boot off 3 of these disks into the exact same bootloader. This means that all of these disks have the bootable flag set on their MBR, even though I had been under the impression that only 2 of them are in fact bootable. My question is: is there an easy way to check which disks have a bootable MBR with a command line tool or some OS utility? I am aware of the DISKPART tool and its basic functionality, but I haven't found how to view the information I need. The OS is Windows 7 x64 Ultimate with SP1.

    Read the article

  • Windows 7 Bootcamp to see data doubler SATA SSD in Optical Bay Connector

    - by bumble_bee_tuna
    Hi I purchased a OWC data doubler http://eshop.macsales.com/item/OWC/DDAMBS0GB/ ... Long story short it lets you add a second HD to your macbook pro in place of the cd/dvd drive (which is useless anyway, impossible to get stuff out when stuck). My current setup is 600gb intel SSD bootdrive 100gb partition for OSX / 500gb for Windows 7 Prof from Bootcamp (use 99 % of time). My desire is to have a second 300gb SSD to run disk intensive VM's off of. So I added a second 300gb intel SSD (again, NO desire to boot off of) on the sata optical port. I can see the drive no problem if I boot in to OSX, however, can't see it in disk management on Win7 ??? Any ideas similar experience ... Funny thing is I can see it in "Device Manager Disk Drivers" but not Disk Management ??? Also no I don't want to use Fusion/Parallels this is a waste of resources for me.

    Read the article

< Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >