Search Results

Search found 7486 results on 300 pages for 'auto indent'.

Page 103/300 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

  • How do I apply multiple subnets to a server with one NIC?

    - by Cosban
    I am trying to route multiple IPs through one physical NIC on my dedicated server for use with Proxmox KVM VMs. I have a dedicated server which is currently running Debian 4.4.5-8 with 3 available ip addresses for use, which will be displayed as 176.xxx.xxx.196 (main), 176.xxx.xxx.198 (on same subnet as main) and 5.xxx.xxx.166 (different subnet). I am currently trying to route the third IP address with the dedi for use with a vps that I have set up using proxmox v2.x but am having a really, really hard time doing so. Virtual interfaces binding the additional IP addresses work as expected, ruling out external routing problems. The provider has given the following information for the IP addresses on the main subnet: gateway: 176.xxx.xxx.193 netmask: 255.255.255.224 broadcast: 176.xxx.xxx.223 As well as the following information for the IP address on the second subnet: gateway: 5.xxx.xxx.161 netmask: 255.255.255.248 broadcast: 5.xxx.xxx.167 Everything I've tried with /etc/network/interfaces has either not worked, or has rendered the network completely useless. This is the current state of the file, which has the secondary IP address working on the same subnet as well as IPv6 working, but not the second subnet. # Nativen IPv6 Schnittstelle iface eth0 inet6 manual # Bridge IPv4 Schnittstelle (176.xxx.xxx.193/27) auto vmbr0 iface vmbr0 inet static address 176.xxx.xxx.196 netmask 255.255.255.224 gateway 176.xxx.xxx.193 broadcast 176.xxx.xxx.223 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 post-up ip addr add 176.xxx.xxx.198/27 dev vmbr0 auto vmbr1 iface vmbr1 inet static address 5.xxx.xxx.166 netmask 255.255.255.248 gateway 5.xxx.xxx.161 broadcast 5.xxx.xxx.167 bridge_ports eth0 bridge_stp off bridge_fd 0 bridge_maxwait 0 post-up ip addr add 5.xxx.xxx.166/27 dev vmbr1 # Bridge IPv6 Schnittstelle (Reichweite: xxxx:xxxx:xxxx:xxxx:xxxx:xxxx::/64) iface vmbr0 inet6 static address xxxx:xxxx:xxxx:xxxx:xxxx:xxxx netmask 64 up ip -6 route add xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 down ip -6 route del xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 up ip -6 route add default via xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0 down ip -6 route del default via xxxx:xxxx:xxxx:xxxx:xxxx:xxxx dev vmbr0

    Read the article

  • Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

    - by neezer
    For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

    Read the article

  • Why is Windows Update trying to install an update I don't need?

    - by Oliver Salzburg
    I have a Windows 7 system that currently has a single update pending: Windows Internet Explorer 9 for Windows 7 for x64-based Systems If I try to install the update, Windows Update will: Create a restore point Fail with the error: Code 9C48 Windows Update encountered an error. The event log for the event reads: Installation Failure: Windows failed to install the following update with error 0x80070643: Windows Internet Explorer 9 for Windows 7 for x64-based Systems. If you search the web for that error, there are many other people with the exact same issue. Sadly, I am unable to apply the proposed solutions to my case, because I just installed this system. There is nothing on it, except Windows 7. I installed the system and ran through the updates. I also did the exact same process with this machine several times over the past few days due to a long-term test we just started. I didn't have any problems with any Windows Update on the previous installation runs and I know I didn't do anything different this time because I followed the installation procedures instructions which are to be used during the test. How did this happen and how do I solve it? Further Investigation So, as I always like to do, I ran the update again while running Process Monitor and dug up further details. WindowsUpdate.log First of all, there is a Windows Update log file located at C:\Windows\WindowsUpdate.log which I didn't know about. But I fail to see any significant entry in it, maybe you're more lucky: 2012-04-10 22:46:58:017 956 728 AU AU received approval from Ux for 1 updates 2012-04-10 22:46:58:017 956 728 AU AU setting pending client directive to 'Progress Ux' 2012-04-10 22:46:58:095 956 728 AU BeginInteractiveInstall invoked for Download 2012-04-10 22:46:58:095 956 728 AU Auto-approving update for download, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, ForUx=1, IsOwnerUx=1, HasDeadline=0, IsMinor=0 2012-04-10 22:46:58:095 956 728 AU Auto-approved 1 update(s) for download (for Ux) 2012-04-10 22:46:58:110 956 728 AU UpdateDownloadProperties: 0 download(s) are still in progress. 2012-04-10 22:46:58:110 956 728 AU ############# 2012-04-10 22:46:58:110 956 728 AU ## START ## AU: Download updates 2012-04-10 22:46:58:110 956 728 AU ######### 2012-04-10 22:46:58:110 956 728 AU # Approved updates = 1 2012-04-10 22:46:58:110 956 728 AU AU initiated download, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, callId = {35DF928B-B428-4BAC-8C63-55295967EFBB} 2012-04-10 22:46:58:110 956 728 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:46:58:110 956 728 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:110 956 728 AU Currently showing Progress UX client - so not launching any other client 2012-04-10 22:46:58:110 956 bb8 DnldMgr ************* 2012-04-10 22:46:58:110 956 bb8 DnldMgr ** START ** DnldMgr: Downloading updates [CallerId = AutomaticUpdatesWuApp] 2012-04-10 22:46:58:110 956 bb8 DnldMgr ********* 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Call ID = {35DF928B-B428-4BAC-8C63-55295967EFBB} 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Priority = 3, Interactive = 1, Owner is system = 0, Explicit proxy = 0, Proxy session id = 1, ServiceId = {9482F4B4-E343-43B6-B170-9A65BC822C77} 2012-04-10 22:46:58:110 956 bb8 DnldMgr * Updates to download = 1 2012-04-10 22:46:58:110 956 bb8 Agent * Title = Windows Internet Explorer 9 for Windows 7 for x64-based Systems 2012-04-10 22:46:58:110 956 bb8 Agent * UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100 2012-04-10 22:46:58:110 956 bb8 Agent * Bundles 1 updates: 2012-04-10 22:46:58:110 956 bb8 Agent * {6D9A90B7-FAF9-4A47-9EFE-A506264873B3}.100 2012-04-10 22:46:58:110 956 bb8 DnldMgr *********** DnldMgr: New download job [UpdateId = {6D9A90B7-FAF9-4A47-9EFE-A506264873B3}.100] *********** 2012-04-10 22:46:58:110 956 728 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:110 956 728 AU # Pending download calls = 1 2012-04-10 22:46:58:110 956 728 AU ## RESUMED ## AU: Download update [UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}, succeeded] 2012-04-10 22:46:58:313 956 bb8 Agent ** END ** Agent: Downloading updates [CallerId = AutomaticUpdatesWuApp] 2012-04-10 22:46:58:313 956 bb8 Agent ************* 2012-04-10 22:46:58:313 956 718 AU ######### 2012-04-10 22:46:58:313 956 718 AU ## END ## AU: Download updates 2012-04-10 22:46:58:313 956 718 AU ############# 2012-04-10 22:46:58:313 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:46:58:313 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:313 956 718 AU Currently showing Progress UX client - so not launching any other client 2012-04-10 22:46:58:313 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:46:58:313 956 aac AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:46:58:313 956 aac AU No featured updates available. 2012-04-10 22:47:00:107 956 aac AU BeginInteractiveInstall invoked for Install 2012-04-10 22:47:00:107 956 aac AU Auto-approving update for install, updateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}.100, ForUx=1, IsOwnerUx=1, HasDeadline=0, IsMinor=0 2012-04-10 22:47:00:107 956 aac AU Auto-approved 1 update(s) for install (for Ux), installType=1 2012-04-10 22:47:00:107 956 aac AU ############# 2012-04-10 22:47:00:107 956 aac AU ## START ## AU: Install updates 2012-04-10 22:47:00:107 956 aac AU ######### 2012-04-10 22:47:00:107 956 aac AU # Initiating manual install 2012-04-10 22:47:00:107 956 aac AU # Approved updates = 1 2012-04-10 22:47:00:107 956 aac AU ## RESUMED ## AU: Installing update [UpdateId = {B33ACEC1-3265-4D01-9C37-AC0892E95ED9}] 2012-04-10 22:47:13:773 2232 9fc Handler : WARNING: Exit code = 0x8024200B 2012-04-10 22:47:13:773 956 718 AU # WARNING: Install failed, error = 0x80070643 / 0x00009C48 2012-04-10 22:47:13:773 2232 9fc Handler ::::::::: 2012-04-10 22:47:13:773 2232 9fc Handler :: END :: Handler: Command Line Install 2012-04-10 22:47:13:773 2232 9fc Handler ::::::::::::: 2012-04-10 22:47:13:851 956 a7c Agent ********* 2012-04-10 22:47:13:851 956 a7c Agent ** END ** Agent: Installing updates [CallerId = AutomaticUpdates] 2012-04-10 22:47:13:851 956 718 AU Install call completed. 2012-04-10 22:47:13:851 956 a7c Agent ************* 2012-04-10 22:47:13:851 956 718 AU # WARNING: Install call completed, reboot required = No, error = 0x00000000 2012-04-10 22:47:13:851 956 718 AU ######### 2012-04-10 22:47:13:851 956 718 AU ## END ## AU: Installing updates [CallId = {FCFF2A5C-25AB-4FB9-AB2B-35C65CCA6A9F}] 2012-04-10 22:47:13:851 956 718 AU ############# 2012-04-10 22:47:13:851 956 718 AU Install complete for all calls, reboot NOT needed 2012-04-10 22:47:13:851 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:47:13:851 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:13:851 956 498 AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:47:13:851 956 498 AU No featured updates available. 2012-04-10 22:47:14:366 956 168 AU No featured updates notifications to show 2012-04-10 22:47:14:366 956 168 AU UpdateDownloadProperties: 0 download(s) are still in progress. 2012-04-10 22:47:14:366 956 168 AU Triggering Offline detection (non-interactive) 2012-04-10 22:47:14:366 956 168 AU AU setting pending client directive to 'Install Complete Ux' 2012-04-10 22:47:14:366 956 168 AU Changing existing AU client directive from 'Progress Ux' to 'Install Complete Ux', session id = 0x1 2012-04-10 22:47:14:366 956 168 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:14:366 956 b78 AU ############# 2012-04-10 22:47:14:366 956 b78 AU ## START ## AU: Search for updates 2012-04-10 22:47:14:366 956 b78 AU ######### 2012-04-10 22:47:14:366 956 b78 AU ## RESUMED ## AU: Search for updates [CallId = {0198DD3A-D7B0-48F5-A77D-795F8A1BDCE8}] 2012-04-10 22:47:16:097 956 718 AU # 1 updates detected 2012-04-10 22:47:16:097 956 718 AU ######### 2012-04-10 22:47:16:097 956 718 AU ## END ## AU: Search for updates [CallId = {0198DD3A-D7B0-48F5-A77D-795F8A1BDCE8}] 2012-04-10 22:47:16:097 956 718 AU ############# 2012-04-10 22:47:16:097 956 718 AU No featured updates notifications to show 2012-04-10 22:47:16:097 956 718 AU Setting AU scheduled install time to 2012-04-11 01:00:00 2012-04-10 22:47:16:097 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:16:097 956 718 AU Successfully wrote event for AU health state:0 2012-04-10 22:47:16:113 956 55c AU Getting featured update notifications. fIncludeDismissed = true 2012-04-10 22:47:16:113 956 55c AU No featured updates available. 2012-04-10 22:47:18:780 956 bb8 Report REPORT EVENT: {27479C66-E930-4F9C-AFF2-27EDD76DED8F} 2012-04-10 22:47:13:773+0200 1 182 101 {B33ACEC1-3265-4D01-9C37-AC0892E95ED9} 100 80070643 AutomaticUpdates Failure Content Install Installation Failure: Windows failed to install the following update with error 0x80070643: Windows Internet Explorer 9 for Windows 7 for x64-based Systems. 2012-04-10 22:47:18:780 956 bb8 Report CWERReporter::HandleEvents - WER report upload completed with status 0x8 2012-04-10 22:47:18:780 956 bb8 Report WER Report sent: 7.5.7601.17514 0x80070643 B33ACEC1-3265-4D01-9C37-AC0892E95ED9 Install 101 Unmanaged 2012-04-10 22:47:18:780 956 bb8 Report CWERReporter finishing event handling. (00000000) WU-IE9-Windows7-x64.exe The actual update that is executed is downloaded and stored at the following location: C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe Executing that file manually, results in the following error message: IE9_main.log The IE9 installer/updater also creates an own log file located at C:\Windows\IE9_main.log For the update session in question, the installer logged: 00:00.000: ==================================================================== 00:00.016: Started: 2012/04/10 (Y/M/D) 23:10:53.897 (local) 00:00.032: Time Format in this log: MM:ss.mmm (minutes:seconds.milliseconds) 00:00.063: Command line: "C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe" 00:00.078: INFO: Setup installer for Internet Explorer: 9.0.8112.16421 00:00.094: INFO: Previous version of Internet Explorer: 9.0.8112.16443 00:00.110: INFO: Checking if iexplore.exe's current version is between 9.0.6001.0... 00:00.125: INFO: ...and 9.1.0.0... 00:00.141: INFO: Maximum version on which to run IEAK branding is: 9.1.0.0... 00:00.156: ERROR: A newer version of Internet Explorer is already installed on the system. 00:00.188: ERROR: Internet Explorer version check failed. 01:03.789: INFO: Setup exit code: 0x00009C48 (40008) - A more recent version of Internet Explorer is installed. 01:03.820: INFO: Scheduling upload to IE SQM server: http://sqm.microsoft.com/sqm/ie/sqmserver.dll 01:03.852: INFO: SQM Upload returned 403 01:03.867: INFO: Cleaning up temporary files in: C:\Windows\TEMP\IE978E.tmp 01:03.883: INFO: Unable to remove directory C:\Windows\TEMP\IE978E.tmp, marking for deletion on reboot. 01:03.898: INFO: Released Internet Explorer Installer Mutex Which pretty much confirms what the error message says when executing the update manually; it's simply already installed or even obsolete because a newer version is installed. So, why does it try to keep installing the update? Possible solutions? Uninstalling Windows Internet Explorer 9 and manually installing the cached C:\Windows\SoftwareDistribution\Download\Install\WU-IE9-Windows7-x64.exe will result in the same error after applying all pending updates. Applying the FixIt for the issue You receive “0x80070643” or “0x643” error codes when you try to install .NET Framework updates through Windows Update or Microsoft Updates will not resolve the issue. Applying the suggested solution for the issue Error message when you try to install updates by using the Windows Update or Microsoft Update Web site: "0x80070003" will not resolve the issue. Running the FixIt Automatically diagnose and fix common problems with Windows Update does report having resolved issues with Windows Update, but didn't resolve the issue. Running the FixIt for the issue How to troubleshoot Windows Update or Microsoft Update when you are repeatedly offered an update does not resolve the issue. Neither with normal nor with aggressive settings.

    Read the article

  • multiple ip for a server not reachable

    - by andrewk
    FYI: I've read everything on Serverfault related to this question and have faced a different issue. Simply put, I've got one server (apache2) with couple of sites on it. It currently has 1 ip. I'm trying to assign/add another ip to that server, so I can give each site a different ip for ssl purposes. I am not lucking out. The new ip simply is unreachable, I've pinged it. This is what I've got below, what am I doing wrong. auto lo iface lo inet loopback auto eth0 eth0:0 eth0:1 iface eth0 inet static address 70.116.5.244 netmask 255.255.255.0 gateway 70.116.5.1 #THE NEW IP iface eth0:0 inet static address 26.175.217.102 netmask 255.255.255.0 #PRIVATE IP iface eth0:1 inet static address 192.168.158.88 netmask 255.255.128.0 NOTE: THESE IP'S ARE TWEAKED BUT RELATIVE I've read many questions here 90% similar to this but most actually have the IP respond, not this case. Thanks netstar -r output Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default gw-u6.linode.co 0.0.0.0 UG 0 0 0 eth0 70.116.5.0 * 255.255.255.0 U 0 0 0 eth0 26.175.217.0 * 255.255.255.0 U 0 0 0 eth0 192.168.128.0 * 255.255.128.0 U 0 0 0 eth0

    Read the article

  • [Ubuntu 10.04] mdadm - Can't get RAID5 Array To Start

    - by Matthew Hodgkins
    Hello, after a power failure my RAID array refuses to start. When I boot I have to sudo mdadm --assemble --force /dev/md0 /dev/sdb1 /dev/sdc1 /dev/sdd1 /dev/sde1 /dev/sdf1 /dev/sdg1 to get mdadm to notice the array. Here are the details (after I force assemble). sudo mdadm --misc --detail /dev/md0: /dev/md0: Version : 00.90 Creation Time : Sun Apr 25 01:39:25 2010 Raid Level : raid5 Used Dev Size : 1465135872 (1397.26 GiB 1500.30 GB) Raid Devices : 6 Total Devices : 6 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 17 23:02:38 2010 State : active, Not Started Active Devices : 6 Working Devices : 6 Failed Devices : 0 Spare Devices : 0 Layout : left-symmetric Chunk Size : 128K UUID : 44a8f730:b9bea6ea:3a28392c:12b22235 (local to host hodge-fs) Events : 0.1249691 Number Major Minor RaidDevice State 0 8 65 0 active sync /dev/sde1 1 8 81 1 active sync /dev/sdf1 2 8 97 2 active sync /dev/sdg1 3 8 49 3 active sync /dev/sdd1 4 8 33 4 active sync /dev/sdc1 5 8 17 5 active sync /dev/sdb1 mdadm.conf: # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions /dev/sdb1 /dev/sdb1 # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # definitions of existing MD arrays ARRAY /dev/md0 level=raid5 num-devices=6 UUID=44a8f730:b9bea6ea:3a28392c:12b22235 Any help would be appreciated.

    Read the article

  • CSS gradient not rendering in Windows Phone 8 WebBrowser Control

    - by SRSHawk
    I am facing an issue where, the CSS3 background is not rendered in WebBrowser control in Windows Phone 8. But same HTML when opened in WebBrowser in Windows Phone 8, it renders the gradient The HTML I am using is: <html> <head> <meta name="viewport" content="width=320, user-scalable=no, minimum-scale=1, maximum-scale=1"/> </head> <body style="margin:0px;overflow:hidden;"> <div id="im_c" style="height:48px;width:100%25; background: -ms-linear-gradient( bottom, #432100 30%, #00AAAA 70%);"> <div style="margin:0 auto;width:320px;"> Test </div> </div> <style> body {margin:0px} </style> </body> In Windows Phone 8, I use the HTML as below: WebBroswer WebView = new WebBrowser(); WebView.Height = 100; WebView.Width = 400; WebView.NavigateToString(@"<html><head><meta name=""viewport"" content=""width=320, user-scalable=no, minimum-scale=1, maximum-scale=1""/></head><body style=""margin:0px;overflow:hidden;""> <div id=""im_c"" style=""height:48px;width:100%25; background: -ms-linear-gradient( bottom, #432100 30%, #00AAAA 70%);""> <div style=""margin:0 auto;width:320px;"">Test</div></div> <style> body {margin:0px} </style> </body></html>"); In this case, the CSS gradient is not visible. Am I missing something?

    Read the article

  • Does fast typing influence fast programming?

    - by Lukasz Lew
    Many young programmers think that their bottleneck is typing speed. After some experience one realizes that it is not the case, you have to think much more than type. At some point my room-mate forced me to turn of the light (he sleeps during the night). I had to learn to touch type and I experienced an actual improvement in programming skill. The most surprising was that the improvement not due to sheer typing speed, but to a change in mindset. I'm less afraid now to try new things and refactor them later if they work well. It's like having a new tool in the bag. Have anyone of you had similar experience? Now I trained a touch typing a little with KTouch. I find auto-generate lessons the best. I can use this program to create new lessons out of text files but it's only verbatim training, not auto-generated based on a language model. Do you know any touch typing program that allows creation of custom, but randomized lessons?

    Read the article

  • Find out the type of an automounted device

    - by Steve Bennett
    I'm working on a system (Ubuntu Precise) with a mount defined in /etc/fstab as follows: /dev/vdb /mnt auto defaults,nobootwait,comment=cloudconfig 0 2 Originally I just wanted to find out if it's NFS (due to potential MySQL locking issues). Judging from man mount, it's not: If no -t option is given, or if the auto type is specified, mount will try to guess the desired type. Mount uses the blkid library for guessing the filesystem type; if that does not turn up anything that looks familiar, mount will try to read the file /etc/filesystems, or, if that does not exist, /proc/filesystems. All of the filesystem types listed there will be tried, except for those that are labeled "nodev" (e.g., devpts, proc and nfs). If /etc/filesystems ends in a line with a single * only, mount will read /proc/filesystems afterwards. But, out of curiosity now, how can I find out more about what type of device it actually is? (For context, this is a VM running on OpenStack. The device is a 60Gb allocation mounted from somewhere - but I don't know how.)` EDIT Including answers here: $ mount /dev/vdb on /mnt type ext3 (rw,_netdev) $ df -T /dev/vdb ext3 61927420 2936068 55845624 5% /mnt

    Read the article

  • Why is the link between my switch and my router always negotiating half-duplex mode?

    - by Massimo
    I have a Cisco 2950 switch which has one of its ports connected to an Internet router provided by my ISP; I have no access to the router configuration, but I manage the switch. If I leave all switch ports with their default setup (auto-negotiation of speed and duplex mode), this link always connects at 100 MBit/s, but in half-duplex mode. I've tried replacing the cable, and also moving the link to another switch port: the result is always the same. A different device connected to the same port (or to any switch port, really) shows no problem at all. It could be guesed that someone configured the router to only connect in half-duplex mode... BUT, here's the catch: if I manually force the switch port to full-duplex mode (duplex full in the interface configuration), the link goes up, stays up and is completely stable. So: The connection is not forced to half-duplex mode by the router, otherwise it would not connect at all if I force the switch end to full-duplex. There is no actual link problem, otherwise the full-duplex connection would not go up or would at least show some errors. But if I leave the port free to auto-negotiate, it always connects in half-duplex mode. Why?

    Read the article

  • No signal on monitor after plug it to a linux box

    - by yaroot
    I use my old computer as an NAS, so I remove the monitor after I installed linux on it (disconnect vga cable). I use ssh to control the machine and it works fine. Until some day, after kernel/softare upgrade or messing up some configs, I cannot connect to it through ssh, then I have to plug the monitor back, but the monitor says "No input signal". So I have to restart the computer WITH the monitor connected, and the monitor's back! I think the computer/linux kernel doesn't detect the monitor plug-in event. So how can I start my linux box without a monitor, but when it goes wrong I can still plug my monitor (vga) back and use the console. Edit: just one pci-e video card, has dvi, vga, tv/out (s-video) Edit2: Xorg is not running. I just need the console (CTRL+ALT+F1). The problem is, if the machine booted without a monitor connected, it won't give me a pseudo terminal after I attach the vga cable while it's running. Clearly the monitor is not auto detected as usb device. I'm wondering how to let the monitor auto detected.

    Read the article

  • Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

    - by Damainman
    I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

    Read the article

  • IIS6 Virtual SMTP server isn't coming back up automatically after a system restart

    - by Julian James
    I've got a virtual server running Win2008 RC2. I've set up IIS6 with a virtual SMTP server on it to be the mail provider for the websites I'm hosting there. It all works great, but if for some reason the server reboots (auto updates are still enabled - I'm trying to make this as little work as possible as we've got a Lot of clients), the IIS6 doesn't restart the SMTP server. The failure causes 500 errors on the current setup, so I'm spending half the day apologising. Any ideas? In Services I've set everything to come back up automatically, but still no dice. As soon as I restart the SMTP, no problems, all the mail gets sent. It's working perfectly, it just won't restart on it's own. I'd really rather not turn auto updates off as we're such a small company I just can't spare the time to be manually updating 15 copies of windows every time MS decide there's a security patch. All advice appreciated! BTW, I am a complete newb to these forums. I searched but couldn't find an answer, so please be nice. But firm. I've got to learn here.

    Read the article

  • Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues...

    - by upkels
    I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

    Read the article

  • Kickstart CentOS 6 prompting for TCP/IP with network set to DHCP

    - by Andy Shinn
    I am trying to stop my kickstart CentOS install prompting me for TCP/IP information. After I click through this prompt (keeping IPv4 and IPv6 to their defaults) the installation continues and completes just fine. Below is my kickstart file: # Andy's super awesome VM kickstart file install url --url=http://mirrors.kernel.org/centos/6/os/x86_64 lang en_US.UTF-8 keyboard us text %include /tmp/network.ks rootpw --iscrypted $6$RA8DyrNTsVJkGIgY$ohZ62HHiOjNnn1yDMZlIu3lQ63D3plGPcbVZtPKE8Oq6Z.IGUgN.kNLkxs/ZymZuluRDWsW2eey5zLOl2G3mp. firewall --service=ssh authconfig --enableshadow --passalgo=sha512 selinux --disabled timezone America/Los_Angeles bootloader --location=mbr --driveorder=vda --append="crashkernel=auto rhgb quiet" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work zerombr clearpart --all --drives=vda --initlabel part /boot --fstype=ext4 --size=500 part pv.253002 --grow --size=1 volgroup vg1 --pesize=4096 pv.253002 logvol / --fstype=ext4 --name=lv_root --vgname=vg1 --grow --size=1024 --maxsize=51200 logvol swap --name=lv_swap --vgname=vg1 --grow --size=4032 --maxsize=4032 repo --name="CentOS" --baseurl=http://mirrors.kernel.org/centos/6/os/x86_64 --cost=100 repo --name="Puppet Labs Products" --baseurl=http://yum.puppetlabs.com/el/6/products/x86_64 repo --name="Puppet Labs Dependencies" --baseurl=http://yum.puppetlabs.com/el/6/dependencies/x86_64 repo --name="EyeFi" --baseurl=http://flexo.eye.fi/6/eye-fi-api %packages @core @server-policy puppet facter %end %pre --erroronfail #!/bin/bash for x in `cat /proc/cmdline`; do case $x in SERVERNAME*) eval $x echo "network --onboot yes --device eth0 --bootproto dhcp --hostname ${SERVERNAME}.eye.fi" /tmp/network.ks ;; esac; done %end %post puppet agent --waitforcert 10 --onetime --no-daemon --pluginsync --server puppet.eye.fi %end reboot My kernel arguments are in this following virt-install command that I use to start the install: virt-install -n zabbix -r 2048 --vcpus=2 -l http://mirrors.kernel.org/centos/6/os/x86_64 --disk /dev/vg_inf1/zabbix --network bridge=br85 --initrd-inject=/home/ashinn/vm_kickstart --extra-args "ks=file:/vm_kickstart SERVERNAME=zabbix" --autostart During the install, I can pull up a console on the second terminal and verify the contents of /tmp/network.ks are: network --onboot=yes --bootproto=dhcp --ipv6=auto --hostname=jenkins2.mydomain.com Why might Anaconda be prompting for the TCP/IP settings when they are already set to DHCP?

    Read the article

  • management network to a network port for additional ones munin and monit

    - by paolo
    management network to a network port for additional ones munin and monit I want to build a separate Netzwek for server management. I have several network cards a linux / debian / ubuntu with computer. Set both network cards sin in the /etc/network/interfaces. # The primary network interface #allow-hotplug eth0 #iface eth0 inet dhcp auto eth0 iface eth0 inet static address 10.0.0.240 netmast 255.255.255.0 network 10.0.0.0 brodacast 10.0.0.255 gateway 10.0.0.254 auto eth1 iface eth1 inet static address 10.0.10.240 netmast 255.255.255.0 network 10.0.10.0 brodacast 10.0.10.255 post-up ip route add 10.0.0.0/24 dev eth0 src 10.0.0.240 table eth0-WAN post-up ip route add default via 10.0.0.254 table eth0-WAN post-up ip route add 10.0.10.0/24 dev eth1 src 10.0.10.240 table eth1-LAN post-up ip route add default via 10.0.10.200 table eth1-LAN post-up ip rule add from 10.0.0.240 table eth0-WAN post-up ip rule add from 10.0.10.240 table eth1-LAN still i adjusted / etc/iproute2/rt_tables and following routes set up in the /etc/network/interfaces I want to have both applications and the network interface separately as munin and monit only on eth1 and not have to eth0. it goes to the reboot but sometimes not always. # Traceroute-i eth1 10.0.10.200 not go what am I doing wrong?

    Read the article

  • Configured Samba to join our domain, but logon fails from Windows machine

    - by jasonh
    I've configured a Fedora 11 installation to join our domain. It seems to join successfully (though it reports a DNS update failure) but when I try to access \\fedoraserver.test.mycompany.com I'm prompted for a password. So I enter adminuser and the password and that fails, so I try test.mycompany.com\adminuser and that too fails. What am I missing? EDIT (Update 9/1/09): I can now connect to the machine and see the shares on it (see my response to djhowell's answer) but when I try to connect, I get an error saying The network path was not found. I checked the log entry on the Fedora computer for the computer I'm connecting from (/var/log/samba/log.ComputerX) and it reads: [2009/09/01 12:02:46, 1] libads/cldap.c:recv_cldap_netlogon(157) no reply received to cldap netlogon [2009/09/01 12:02:46, 1] libads/ldap.c:ads_find_dc(417) ads_find_dc: failed to find a valid DC on our site (Default-First-Site-Name), trying to find another DC Config files as of 9/1/09: smb.conf: [global] Workgroup = TEST realm = TEST.MYCOMPANY.COM password server = DC.TEST.MYCOMPANY.COM security = DOMAIN server string = Test Samba Server log file = /var/log/samba/log.%m max log size = 50 idmap uid = 15000-20000 idmap gid = 15000-20000 windbind use default domain = yes cups options = raw client use spnego = no server signing = auto client signing = auto [share] comment = Test Share path = /mnt/storage1 valid users = adminuser admin users = adminuser read list = adminuser write list = adminuser read only = No I also set the krb5.conf file to look like this: [logging] default = FILE:/var/log/krb5libs.log kdc = FILE:/var/log/krb5kdc.log admin_server = FILE:/var/log/kadmind.log [libdefaults] default_realm = test.mycompany.com dns_lookup_realm = false dns_lookup_kdc = false ticket_lifetime = 24h forwardable = yes [realms] TEST.MYCOMPANY.COM = { kdc = dc.test.mycompany.com admin_server = dc.test.mycompany.com default_domain = test.mycompany.com } [domain_realm] dc.test.mycompany.com = test.mycompany.com .dc.test.mycompany.com = test.mycompany.com [appdefaults] pam = { debug = false ticket_lifetime = 36000 renew_lifetime = 36000 forwardable = true krb4_convert = false } I realize that there might be an issue with EXAMPLE.COM in there, however if I change it to TEST.MYCOMPANY.COM then it fails to join the domain with a preauthentication failure. As of 9/1/09, this is no longer the case.

    Read the article

  • DNS issue on Fedora 12? wget wordpress.org fails where wget www.google.com works

    - by Tom Auger
    I'm administering a Fedora 12 box, but am quite new to networking specifics. Recently one of our WordPress apps hosted on our server has stopped being able to perform its auto-update or auto-download of plugins. Investigating further, I have tried the following: $ wget wordpress.org --2010-12-17 11:26:50-- http://wordpress.org/ Resolving wordpress.org... failed: Temporary failure in name resolution. wget: unable to resolve host address âwordpress.orgâ Whereas: $ wget www.google.com --2010-12-17 11:27:26-- http://www.google.com/ Resolving www.google.com... 74.125.226.82, 74.125.226.84, 74.125.226.80, ... Connecting to www.google.com|74.125.226.82|:80... connected. HTTP request sent, awaiting response... 302 Found Location: http://www.google.ca/ [following] --2010-12-17 11:27:26-- http://www.google.ca/ Resolving www.google.ca... 173.194.32.104 Connecting to www.google.ca|173.194.32.104|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: âindex.html.4â [ <=> ] 9,079 --.-K/s in 0.02s 2010-12-17 11:27:26 (462 KB/s) - âindex.html.4â Interestingly: $ ping wordpress.org PING wordpress.org (72.233.56.138) 56(84) bytes of data. 64 bytes from wordpress.org (72.233.56.138): icmp_seq=1 ttl=50 time=81.5 ms 64 bytes from wordpress.org (72.233.56.138): icmp_seq=2 ttl=50 time=67.3 ms ^C --- wordpress.org ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1783ms rtt min/avg/max/mdev = 67.361/74.448/81.536/7.092 ms and $ nslookup wordpress.org Server: 192.168.2.1 Address: 192.168.2.1#53 Non-authoritative answer: Name: wordpress.org Address: 72.233.56.138 Name: wordpress.org Address: 72.233.56.139 nscd has been stopped and flushed. iptables appear to be clean. At this point I have exhausted my limited abilities to diagnose the issue. Can anyone suggest a resolution path?

    Read the article

  • SSH multi-hop connections with netcat mode proxy

    - by aef
    Since OpenSSH 5.4 there is a new feature called natcat mode, which allows you to bind STDIN and STDOUT of local SSH client to a TCP port accessible through the remote SSH server. This mode is enabled by simply calling ssh -W [HOST]:[PORT] Theoretically this should be ideal for use in the ProxyCommand setting in per-host SSH configurations, which was previously often used with the nc (netcat) command. ProxyCommand allows you to configure a machine as proxy between you local machine and the target SSH server, for example if the target SSH server is hidden behind a firewall. The problem now is, that instead of working, it throws a cryptic error message in my face: Bad packet length 1397966893. Disconnecting: Packet corrupt Here is an excerpt from my ~/.ssh/config: Host * Protocol 2 ControlMaster auto ControlPath ~/.ssh/cm_socket/%r@%h:%p ControlPersist 4h Host proxy-host proxy-host.my-domain.tld HostName proxy-host.my-domain.tld ForwardAgent yes Host target-server target-server.my-domain.tld HostName target-server.my-domain.tld ProxyCommand ssh -W %h:%p proxy-host ForwardAgent yes As you can see here, I'm using the ControlMaster feature so I don't have to open more than one SSH connection per-host. The client machine I tested this with is an Ubuntu 11.10 (x86_64) and both proxy-host and target-server are Debian Wheezy Beta 3 (x86_64) machines. The error happens when I call ssh target-server. When I call it with the -v flag, here is what I get additionally: OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /home/aef/.ssh/config debug1: Applying options for * debug1: Applying options for target-server.my-domain.tld debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: auto-mux: Trying existing master debug1: Control socket "/home/aef/.ssh/cm_socket/[email protected]:22" does not exist debug1: Executing proxy command: exec ssh -W target-server.my-domain.tld:22 proxy-host.my-domain.tld debug1: identity file /home/aef/.ssh/id_rsa type -1 debug1: identity file /home/aef/.ssh/id_rsa-cert type -1 debug1: identity file /home/aef/.ssh/id_dsa type -1 debug1: identity file /home/aef/.ssh/id_dsa-cert type -1 debug1: identity file /home/aef/.ssh/id_ecdsa type -1 debug1: identity file /home/aef/.ssh/id_ecdsa-cert type -1 debug1: permanently_drop_suid: 1000 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.0p1 Debian-3 debug1: match: OpenSSH_6.0p1 Debian-3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8p1 Debian-7ubuntu1 debug1: SSH2_MSG_KEXINIT sent Bad packet length 1397966893. Disconnecting: Packet corrupt

    Read the article

  • How to connect a Win XP PC and Win 7 PC with a Linksys WRT54G Router to a PPPOE connection ?

    - by ChristianM
    I have two PCs and a WRT56G Router. My provider is a PPPOE connection (username and password). I can connect my Windows 7 easily. Even if I choose Auto or PPPOE on the router's configuration. Maybe because this one had the connection in the first place with the username and password set up. But I can't connect the Windows XP PC. Actually it does connect in a way, but it receives and sents just a few packages. I can actually see in My Network Places how many packages does the Gateway make and it's a big difference. And it won't open any page. How should I set up the router so I can give enough bandwith to the Windows XP PC ? I've seen another problem that I forgot to mention. The router can't connect with the pppoe settings. I don't know why, but with Auto DHCP setting and my Windows 7 connected with pppoe settings works. EDIT2: I've installed Win 7 on the other PC so I won't have any problem of compatibility betwen them. But I still can't connect the router with PPPOE settings to the internet. It looks like this: http://img641.imageshack.us/img641/9780/capturefba.png If you need any other screens or info, please tell me.

    Read the article

  • Debian can't connect to internet using LAN

    - by tampe125
    I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

    Read the article

  • Debian can't connect to internet using LAN

    - by tampe125
    I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

    Read the article

  • Solr startup script problem

    - by Camran
    I have installed solr and it works finally... I have now problems setting it up to start automatically with a start command. I have followed a tutorial and created a file called solr in the /etc/init.d/solr dir... Here is that file: #!/bin/sh -e # SOLR auto-start # # description: auto-starts solr engine # processname: solr-production # pidfile: /var/run/solr-production.pid NAME="solr" PIDFILE="/var/run/solr-production.pid" LOG_FILE="/var/log/solr-production.log" SOLR_DIR="/etc/jetty" JAVA_OPTIONS="-Xmx1024m -DSTOP.PORT=8079 -DSTOP.KEY=stopkey -jar start.jar" JAVA="/usr/bin/java" start() { echo -n "Starting $NAME... " if [ -f $PIDFILE ]; then echo "is already running!" else cd $SOLR_DIR $JAVA $JAVA_OPTIONS 2> $LOG_FILE & sleep 2 echo `ps -ef | grep -v grep | grep java | awk '{print $2}'` > $PIDFILE echo "(Done)" fi return 0 } stop() { echo -n "Stopping $NAME... " if [ -f $PIDFILE ]; then cd $SOLR_DIR $JAVA $JAVA_OPTIONS --stop sleep 2 rm $PIDFILE echo "(Done)" else echo "can not stop, it is not running!" fi return 0 } case "$1" in start) start ;; stop) stop ;; restart) stop sleep 5 start ;; *) echo "Usage: $0 (start | stop | restart)" exit 1 ;; esac Whenever I do solr -start I get this error: "Error occurred during initialization of VM Could not reserve enough space for object heap" I think this is because of the file above... Also here is where I have solr installed: var/www/solr and here is the start.jar file located: var/www/start.jar Help me out if you know whats causing this. Thanks BTW: OS is ubuntu 9.10

    Read the article

  • drivers/rtc/hctosys.c: unable to open rtc device (rtc0) after recompile on boot

    - by squareone
    After recompiling a new kernel on CentOS 6.3, using the same kernel I have been using on several other machines, I am getting a kernel panic on two machines. I get the following when trying to boot: drivers/rtc/hctosys.c: unable to open rtc device (rtc0) (flashes this before displaying the panic below) not syncing: Attempted to kill init! exitcode=0x00000100 Pid: 1, comm: init Not tainted etc... I have been trying to figure out what is going on, and am having trouble doing so, and feel I have exhausted all of my options here. Any help would be appreciated. My grub.conf: default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title CentOS (3.4.18-rt29) root (hd0,0) kernel /vmlinuz-3.4.18-rt29 ro root=/dev/mapper/VolGroup-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_NO_MD rd_LVM_LV=VolGroup/lv_swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet panic=5 initrd /initramfs-3.4.18-rt29.img title CentOS (2.6.32-279.14.1.el6.x86_64) root (hd0,0) kernel /vmlinuz-2.6.32-279.14.1.el6.x86_64 ro root=/dev/mapper/VolGroup-lv_root rd_NO_LUKS LANG=en_US.UTF-8 rd_NO_MD rd_LVM_LV=VolGroup/lv_swap SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=VolGroup/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_DM rhgb quiet panic=5 initrd /initramfs-2.6.32-279.14.1.el6.x86_64.img Any help or guidance would be greatly appreciated.

    Read the article

  • Windows VPN for remote site connection drawbacks

    - by Damo
    I'm looking for some thoughts on a particular way of setting up a estate of machines. We have a requirement to install machines into unmanned, remote locations. These machines will auto login and perform tasks controlled from a central server. In order to manage patching, AV, updates etc I want these machines to be joined to a dedicated domain for this estate. Some of the locations will only have 3G connectivity (via other hardware), others will be located on customer premises in internal networks. The central server (of ours) and the Domain Controller will be on a public WAN. I see two ways of facilitating this. Install a router at each location and have a site to site VPN between the remove device and the data centre where the servers are location Have the remote machine dial up and authenticate via a Windows VPN connection to the DC via RAS Option one is more costly to setup and has a higher operational cost. It also offers better diagnostics if the remote PC goes down. Option two works well but is solely dependent on the VPN connection been made before any communication can be made to the remote machine. In a simple test, I can got a Windows 7 machine to dial a VPN prior to authentication to a domain, then automatically login to the machine using domain credentials. If the VPN connection drops, it redials. I can also create a timed task to auto connect every hour in case of other issues. I'd like to know, why (if at all) is operating a remote network of devices which are located in various out of band locations in this way a bad idea? Consider 300-400 remote machines all at different sites. I'd rather have 400 VPN connections to a 2008 server than 400 routers, however I'd like to know other opinions on this.

    Read the article

  • Debian, 2 NICs load-balancing or agregating with one same gateway

    - by pouney
    Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

    Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >