Search Results

Search found 5618 results on 225 pages for 'recursive dns'.

Page 103/225 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

  • Is it good to create a usercontrol for Recursive code in xaml?

    - by user281947
    <Border BorderBrush="#C4C8CC" BorderThickness="0,0,0,1"> <TextBlock x:Name="SectionTitle" FontFamily="Trebuchet MS" FontSize="14" FontWeight="Bold" Foreground="#3D3D3D" /> </Border> I have to use the same above format at many places in a single xaml page, so for this i created a usercontrol and defined the above code inside it. So my question is, What i am doing is it right approach? Will it make the page to load slower then the above code used as it is without defining it in a new user control?

    Read the article

  • Intermittent wired network issues in 14.04

    - by Tommy Brunn
    Since yesterday, my wired network connection has been dropping for a couple of seconds every 30 seconds or so. To my knowledge, I had not made any changes to my network. Output of ifconfig -a: ? ~ ifconfig -a eth0 Link encap:Ethernet HWaddr 6c:f0:49:b9:b1:7f inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:feb9:b17f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11597 errors:0 dropped:0 overruns:0 frame:0 TX packets:9783 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10101682 (10.1 MB) TX bytes:1215142 (1.2 MB) Interrupt:48 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:96691 errors:0 dropped:0 overruns:0 frame:0 TX packets:96691 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:13594355 (13.5 MB) TX bytes:13594355 (13.5 MB) lspci |grep Ethernet: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) Pinging my router: ? ~ ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=0.435 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.571 ms ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable 64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=1.03 ms And the output of route: ? ~ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 1 0 0 eth0 Some messages from /var/logs/syslog: ? ~ tail -f /var/log/syslog Jun 6 10:37:34 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:34 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:37 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:37 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:39 lolbox dhclient: XMT: Solicit on eth0, interval 8660ms. Jun 6 10:37:39 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:39 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:47 lolbox dhclient: XMT: Solicit on eth0, interval 16820ms. Jun 6 10:37:47 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:47 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:04 lolbox dhclient: XMT: Solicit on eth0, interval 34410ms. Jun 6 10:38:04 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:04 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13045 Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:37:34 lolbox whoopsie[1133]: online Jun 6 10:38:16 lolbox whoopsie[1133]: offline Jun 6 10:38:16 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:38:16 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13044 Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:38:16 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:17 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:17 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:17 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:18 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13160 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13161 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:38:18 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:18 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:18 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:18 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:18 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:18 lolbox dhclient: All rights reserved. Jun 6 10:38:18 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:18 lolbox dhclient: Jun 6 10:38:19 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:19 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:19 lolbox dhclient: All rights reserved. Jun 6 10:38:19 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:19 lolbox dhclient: Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:38:19 lolbox dhclient: Bound to *:546 Jun 6 10:38:19 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:38:19 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv6 state changed nbi -> preinit6 Jun 6 10:38:19 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on Socket/fallback Jun 6 10:38:19 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3fc9376d) Jun 6 10:38:19 lolbox dhclient: XMT: Solicit on eth0, interval 1020ms. Jun 6 10:38:19 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:19 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:38:20 lolbox dhclient: bound to 192.168.0.16 -- renewal in 41481 seconds. Jun 6 10:38:20 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:38:20 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:38:20 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:38:20 lolbox dhclient: XMT: Solicit on eth0, interval 2110ms. Jun 6 10:38:20 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:20 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:38:21 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:38:21 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:38:21 lolbox whoopsie[1133]: online Jun 6 10:38:21 lolbox ntpdate[13217]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:38:21 lolbox ntpdate[13217]: no servers can be used, exiting Jun 6 10:38:22 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:38:22 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:38:22 lolbox dhclient: XMT: Solicit on eth0, interval 4080ms. Jun 6 10:38:22 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:22 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:26 lolbox dhclient: XMT: Solicit on eth0, interval 8450ms. Jun 6 10:38:26 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:26 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:35 lolbox dhclient: XMT: Solicit on eth0, interval 16630ms. Jun 6 10:38:35 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:35 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:51 lolbox dhclient: XMT: Solicit on eth0, interval 34860ms. Jun 6 10:38:51 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:51 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:58 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:38:58 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13161 Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:22 lolbox whoopsie[1133]: online Jun 6 10:39:04 lolbox whoopsie[1133]: offline Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:39:04 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:39:04 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13160 Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:39:04 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:05 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:05 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:05 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:06 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13270 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13271 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:39:07 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:07 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:07 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:07 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:07 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:07 lolbox dhclient: All rights reserved. Jun 6 10:39:07 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:07 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:08 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:08 lolbox dhclient: All rights reserved. Jun 6 10:39:08 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:08 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Bound to *:546 Jun 6 10:39:08 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:39:08 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:39:08 lolbox kernel: [ 1446.098590] type=1400 audit(1402043948.002:75): apparmor="DENIED" operation="signal" profile="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=13273 comm="nm-dhcp-client." requested_mask="send" denied_mask="send" signal=term peer="/sbin/dhclient" Jun 6 10:39:08 lolbox kernel: [ 1446.098599] type=1400 audit(1402043948.002:76): apparmor="DENIED" operation="signal" profile="/sbin/dhclient" pid=13273 comm="nm-dhcp-client." requested_mask="receive" denied_mask="receive" signal=term peer="/usr/lib/NetworkManager/nm-dhcp-client.action" Jun 6 10:39:08 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:39:08 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on Socket/fallback Jun 6 10:39:08 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3e0183b9) Jun 6 10:39:08 lolbox dhclient: XMT: Solicit on eth0, interval 1050ms. Jun 6 10:39:08 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:39:08 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:39:09 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:39:09 lolbox dhclient: bound to 192.168.0.16 -- renewal in 35498 seconds. Jun 6 10:39:09 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:39:09 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:39:09 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:10 lolbox dhclient: XMT: Solicit on eth0, interval 2180ms. Jun 6 10:39:10 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:10 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:39:10 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:39:10 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:39:10 lolbox whoopsie[1133]: online Jun 6 10:39:10 lolbox ntpdate[13339]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:39:10 lolbox ntpdate[13339]: no servers can be used, exiting Jun 6 10:39:11 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:39:11 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:39:12 lolbox dhclient: XMT: Solicit on eth0, interval 4350ms. Jun 6 10:39:12 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:12 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:16 lolbox dhclient: XMT: Solicit on eth0, interval 8740ms. Jun 6 10:39:16 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:16 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:17 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:17 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:25 lolbox dhclient: XMT: Solicit on eth0, interval 17610ms. Jun 6 10:39:25 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:25 lolbox dhclient: IA_NA status code NoAddrsAvail.

    Read the article

  • WebsitePanel and BIND integration issues

    - by Fariborz Navidan
    I have setup a new Windows server with WebsitePanel stand alone server installed om. I have configured everything. When create a new space in WSP, the only information saved in the DNS zone file is the SOA record and no A record added. Each service has its own DNS zone template records but they are not reflected in domain's DNS zone. Also when delete the space, DNS zone is not deleted. I am using WebsitePanel 1.2.1

    Read the article

  • Dlink search is hijacking my browser

    - by James
    For months now "DLink search" has been hijacking my search engines. I use google chrome, and I have organized my search engines in the handy dandy "manage search engines" tool about a TRILLION times. It never even says D-link is hacking my search engines. It does not show up! I have read many posts on this forum and others saying that to fix this problem from internet explorer: Setup, internet options, yadayada, magical fairies, and you are solved, but my browser is google chrome! How am I supposed to do this from there! I do not know how to re-setup my Dlink router, which is the cause of the problem! HOW? In those posts with the magical fairies fixing it, HUNDREDS responded saying, "yep, those fairies definitely fixed it right. :)" These people were so satisfied. IT WORKED FOR THEM, WHY NOT ME. I look at it and go ":(" because it does not help me. There are no options for anything to do with this in GOOGLE chrome. PLEASE EXPLAIN and HELP. I see no "SETUP" option, no "Internet Options" button, no anything. BTW the exact posts are these: "Uncheck Advanced DNS in the router internet setup. This will take care of it. I had this problem with my DLink router before." "I had this issue with my DIR-655 and unchecking the Advanced DNS setting in Setup - Internet - Manual Internet Connection Setup fixed it." "If this is just internet explorer, you can go to Tools Internet Options or Internet Options in Control Panel. From here, go to the advanced tab and click the Reset button." "I would set the router's DNS to a site like OpenDNS, and I would ensure the machines are set to get their DNS settings via DHCP or set the machine's DNS setting to OpenDNS. If the router's DNS looks like it was messed with, some bad software know the default passwords for routers and could have changed it. If you don't already I would make sure the password to the router is not default or easy to guess. I've had spyware change a machine's DNS, but the fact it is happening on all machines makes me wonder if it is the router." "Something got into your router and changed the dns server most likely, do a hard reset of the router and then change the password to something strong. Also check for a firmware update for the router and apply it as soon as possible."

    Read the article

  • Python modules import error

    - by Choor
    Very strange for me: # uname -a Linux localhost.localdomain 2.6.18-194.3.1.el5 #1 SMP Thu May 13 13:09:10 EDT 2010 i686 i686 i386 GNU/Linux # pwd /root # python Python 2.6.5 (r265:79063, Apr 11 2010, 22:34:44) [GCC 4.1.2 20080704 (Red Hat 4.1.2-46)] on linux2 Type "help", "copyright", "credits" or "license" for more information. import dns [3]+ Stopped python # cd /home/user/dev/dns [root@localhost dns]# python Python 2.6.5 (r265:79063, Apr 11 2010, 22:34:44) [GCC 4.1.2 20080704 (Red Hat 4.1.2-46)] on linux2 Type "help", "copyright", "credits" or "license" for more information. import dns Traceback (most recent call last): File "", line 1, in File "dns.py", line 1, in import dns.resolver ImportError: No module named resolver [4]+ Stopped python # Summary: I can't import same python module from different path. Any ideas? 0_o P.S. SELINUX=disabled

    Read the article

  • SSH connection times out

    - by mark
    Given: vm - a WinXPsp3 virtual machine hosted by a Win7sp1 physical machine alice is the user on vm srv - a Win2008R2sp1 server bob is the user on srv quake - a linux server mark is the user on quake Both vm and srv have the same new installation of cygwin (1.7.9) and openssh. Firewall service is disabled on vm (and its host) and on srv All the machines can be pinged from all the machines. ssh mark@quake works OK from both vm and srv. ssh bob@srv works OK from both quake and vm. ssh alice@vm works on the vm itself only, but it fails on the other two machines: alice@vm ~ $ ssh alice@vm alice@vm's password: Last login: Tue Oct 25 23:42:09 2011 from vm.shunra.net [mark@Quake ~]$ ssh -vvv alice@vm OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to vm [172.30.2.60] port 22. debug1: connect to address 172.30.2.60 port 22: Connection timed out ssh: connect to host vm port 22: Connection timed out bob@Srv ~ $ ssh -vvv alice@vm OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Connecting to vm [172.30.2.60] port 22. debug1: connect to address 172.30.2.60 port 22: Connection timed out ssh: connect to host vm port 22: Connection timed out I used ssh-host-config both on vm and srv to configure the ssh to run as a windows service. Besides that I did nothing else. Can anyone help me troubleshoot this issue? Thank you very much. EDIT The virtual machine software is VMWare Workstation 7.1.4. I think the problem is in its settings, but I have no idea where exactly. The Network Adapter is set to Bridged. EDIT2 All the machines are located in the company lab, I think all of them are on the same segment, but I may be wrong. Below is the ipconfig /all output for each machine (skipping the linux server). I have deleted the Tunnel adapters to keep the output minimal. If anyone thinks they matter, do tell so and I will post them as well. In addition ping output is given to show that DNS is correct. Something else, may be relevant, may be not. Doing psexec to srv works OK, whereas to vm failes with Access Denied. srv: C:\Windows\system32>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : srv Primary Dns Suffix . . . . . . . : shunra.net Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : shunra.net Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom BCM5709C NetXtreme II GigE (NDIS VBD Client) Physical Address. . . . . . . . . : E4-1F-13-6D-F3-00 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 172.30.6.9(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.248.0 Default Gateway . . . . . . . . . : 172.30.0.254 DNS Servers . . . . . . . . . . . : 172.30.1.1 172.30.1.2 NetBIOS over Tcpip. . . . . . . . : Enabled C:\Windows\system32>ping vm Pinging vm.shunra.net [172.30.2.60] with 32 bytes of data: Reply from 172.30.2.60: bytes=32 time=1ms TTL=128 Reply from 172.30.2.60: bytes=32 time=4ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.2.60: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 4ms, Average = 1ms C:\Windows\system32> vm: C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : vm Primary Dns Suffix . . . . . . . : shunra.net Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : shunra.net shunranet Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : shunranet Description . . . . . . . . . . . : VMware Accelerated AMD PCNet Adapter Physical Address. . . . . . . . . : 00-0C-29-8F-A0-0B Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 172.30.2.60 Subnet Mask . . . . . . . . . . . : 255.255.248.0 Default Gateway . . . . . . . . . : 172.30.0.254 DHCP Server . . . . . . . . . . . : 172.30.1.1 DNS Servers . . . . . . . . . . . : 172.30.1.1 172.30.1.2 Lease Obtained. . . . . . . . . . : Tuesday, October 25, 2011 18:16:34 Lease Expires . . . . . . . . . . : Wednesday, November 02, 2011 18:16:34 C:\>ping srv Pinging srv.shunra.net [172.30.6.9] with 32 bytes of data: Reply from 172.30.6.9: bytes=32 time=1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.6.9: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 1ms, Average = 0ms C:\> vm-host (the host machine of the vm): C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : vm-host Primary Dns Suffix . . . . . . . : shunra.net Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : shunra.net Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC (NDIS 6.20) Physical Address. . . . . . . . . : 6C-F0-49-E7-E9-30 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::f59d:7f6e:1510:6f%10(Preferred) IPv4 Address. . . . . . . . . . . : 172.30.6.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.248.0 Default Gateway . . . . . . . . . : 172.30.0.254 DHCPv6 IAID . . . . . . . . . . . : 242020425 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-CC-39-80-6C-F0-49-E7-E9-30 DNS Servers . . . . . . . . . . . : 172.30.1.1 194.90.1.5 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::cd92:38c0:9a6d:c008%16(Preferred) Autoconfiguration IPv4 Address. . : 169.254.192.8(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 352342102 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-CC-39-80-6C-F0-49-E7-E9-30 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::edb9:b78c:a504:593b%17(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.5.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 369119318 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-CC-39-80-6C-F0-49-E7-E9-30 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled C:\>ping srv Pinging srv.shunra.net [172.30.6.9] with 32 bytes of data: Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Reply from 172.30.6.9: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.6.9: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping vm Pinging vm.shunra.net [172.30.2.60] with 32 bytes of data: Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Reply from 172.30.2.60: bytes=32 time<1ms TTL=128 Ping statistics for 172.30.2.60: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\> EDIT3 I have just checked - the vm-host is able to ssh to the vm machine! I still do not know how to leverage this discovery to solve the problem.

    Read the article

  • How to Impersonate a user for a file copy over the network when dns or netbios is not available

    - by Scott Chamberlain
    I have ComputerA on DomainA running as userA needing to copy a very large file to ComputerB on WorkgroupB which has the ip of 192.168.10.2 to a windows share that only userB has write access to. There is no netbios or dns resolving so the computer must be refrenced by IP I first I tried AppDomain.CurrentDomain.SetPrincipalPolicy(System.Security.Principal.PrincipalPolicy.WindowsPrincipal); WindowsIdentity UserB = new WindowsIdentity("192.168.10.2\\UserB", "PasswordB"); //Execption WindowsImpersonationContext contex = UserB.Impersonate() File.Copy(@"d:\bigfile", @"\\192.168.10.2\bifgile"); contex.Undo(); but I get a System.Security.SecurityException "The name provided is not a properly formed account name." So I tried AppDomain.CurrentDomain.SetPrincipalPolicy(System.Security.Principal.PrincipalPolicy.WindowsPrincipal); WindowsIdentity webinfinty = new WindowsIdentity("ComputerB\\UserB", "PasswordB"); //Execption But I get "Logon failure: unknown user name or bad password." error instead. so then I tried IntPtr token; bool succeded = LogonUser("UserB", "192.168.10.2", "PasswordB", LogonTypes.Network, LogonProviders.Default, out token); if (!succeded) { throw new Win32Exception(Marshal.GetLastWin32Error()); } WindowsImpersonationContext contex = WindowsIdentity.Impersonate(token); (...) [DllImport("advapi32.dll", SetLastError = true)] static extern bool LogonUser( string principal, string authority, string password, LogonTypes logonType, LogonProviders logonProvider, out IntPtr token); but LogonUser returns false with the win32 error "Logon failure: unknown user name or bad password" I know my username and password are fine, I have logged on to computerB as that user. Any reccomandations

    Read the article

  • Is there a security risk for allowing people to set their DNS so their own subdomains can be route to my server?

    - by DantheMan
    Lets say that I have a web application, built in Django and deployed with Nginx. Is it a good idea to offer a service that allows customers to request that a subdomain can be pointed at it. I figured this: If I dont allow this, then some companies wont want to access the service from http://mydjangoappmadeupname.com/bigcorporation/ They would rather access it through http://service.bigcorporation.com That would effectively mask that they are using an outside resource. Is there a significant risk that I am overlooking? Also do you think it would be easier to just set things up in Django to handle it, allowing Nginx to accept all domains and then pushing them to Django which would filter out if they are allowed or not, or would it be better to just update my Nginx log each time a client wanted this changed?

    Read the article

  • Can I get simple name resolution on the local network without DNS, on a Mac?

    - by tim
    I've got Mantis running on a Linux VM with a Win2k8 server host. I installed Samba with the following configuration: [global] workgroup = COMPANY netbios name = MANTIS security = share Now on all our windows machines people can simple go to http://mantis, rather than http://172.16.0.20. However, this doesn't appear to work on the Mac machines. Any ideas how I can sort this without changing anything on the Windows server?

    Read the article

  • Software to monitor bill payment to mission critical IT service providers (ISP, DNS etc.)

    - by Sholom
    Hi All, The Problem: Our very likable but absent minded bookkeeper keeps neglecting to pay our IT vendors on time. Just this past week our internet service was disconnected. Same could happen to many other mission critical accounts (domain registrar, backup MX, anti-virus license, HackerSafe (McAfee secure) service and even an 800 number to name a few). As the sysadmin, i monitor my severs to make sure they are plugged into the power-outlet. I believe i should also monitor my services to make sure they are plugged in to their money-outlet. To compound the problem, when the power goes out someone else will likely notice and notify me. But if a bill is not payed, no one will ever notice until service is lost. Lost as in losing our domain name which would cause a lot more damage then the power failing on our server. [Solution] = [Doesn't work because]: Retrain the bookkeeper = Wishful thinking. Notify my manager = Already have (via email). Protects me, does not solve problem. Fire bookkeeper = What makes you so sure the next one will never forget? Bottom line: Humans are humans and sooner or later something critical will be royally messed up. We need to partner with a machine to help us out here. Anybody have the same problem? What software/solution do you use? I would like software that emails me when a bill is passed due just like i get an email when the power outlet fails. Anyone hear of anything like that? Thanks

    Read the article

  • Sendmail /etc/hosts and DNS ... what is the correct way?

    - by ben
    I found one tutorial on setting up sendmail that says that in the /etc/hosts file, "The entry for 127.0.0.1 must always be followed by the fully qualified domain name (FQDN) of the server." Like so: 127.0.0.1 bigboy.my-site.com localhost.localdomain localhost bigboy (This tutorial is here). However, I can't find anyone else suggesting something like that. instead most people seem to put some combination of localhost and localdomain.localhost after 127.0.0.1, and then some variant of the fully qualified domain name after the public ip address. What is the correct way?

    Read the article

  • Does my DLink DNS-323 need to reside on a "192.168.0.0/24" subnet?

    - by Raymond
    I've installed two brand new 2-tib drives in the DLink and plugged it in to my network. I set my router's static address table to include the MAC address of the device; however it doesn't ever "show up." Do I need to use the custom software to administer this device? Do I need to use a "192.168.0.0/24" network in order for this device to work (asking because it states that if DHCP isn't detected, it will default to an address in that range; and my network is not in that range).

    Read the article

  • Compiling Gnucash 2.6.3 in Ubuntu 14.04

    - by wolveryn
    Downloaded the debian file from source forge and followed instructions, where these errors appear, I re-downloaded the file several times with same error. I want to install the latest Gnucash not the one available on software center. Thank you for your support. /qof/gnc-date/qof print date dmy buff: There are some differences between distros in the way they namelocales, and this can cause trouble with the locale-basedformatting. If you get the assert in this function, run locale -aand make sure that en_US, en_GB, and fr_FR are installed and thatif a suffix is needed it's in the suffixes array.** ERROR:test-gnc-date.c:465:test_gnc_setlocale: code should not be reached FAIL GTester: last random seed: R02Sd8d3d0e67be954baa8ec75d81a14c0e3 /bin/bash: line 1: 18889 Terminated MALLOC_CHECK_=2 MALLOC_PERTURB_=$((${RANDOM:-256} % 256)) gtester --verbose test-qof make[5]: *** [test-nonrecursive] Error 143 make[5]: Leaving directory `/home/ahmed/gnucash/gnucash-2.6.3/src/libqof/qof/test' make[4]: *** [check-am] Error 2 make[4]: Leaving directory `/home/ahmed/gnucash/gnucash-2.6.3/src/libqof/qof/test' make[3]: *** [check-recursive] Error 1 make[3]: Leaving directory `/home/ahmed/gnucash/gnucash-2.6.3/src/libqof/qof' make[2]: *** [check-recursive] Error 1 make[2]: Leaving directory `/home/ahmed/gnucash/gnucash-2.6.3/src/libqof' make[1]: *** [check-recursive] Error 1 make[1]: Leaving directory `/home/ahmed/gnucash/gnucash-2.6.3/src' make: *** [check-recursive] Error 1

    Read the article

  • Microsoft Claims Success Versus Autorun Malware

    Microsoft recently used a post on the Threat Research and Response Blog section of its Malware Protection Center to describe how it is winning the battle against autorun malware. Although there is certainly no shortage of malware in the virtual world Microsoft has plenty of statistics to back its claims and it has displayed them with pride.... DNS Configured Correctly? Test Your Internal DNS With Our Free DNS Advisor Tool From Infoblox.

    Read the article

  • SSL cert issued to and SAN attribute

    - by Jai
    I have added a cert to my application cacerts file. The new cert is issued to one DNS(abc.com) and they have added few other DNS(XYZ.com, TEST.com) to the SAN attribute while creating. I tried accessing one of the DNS(XYZ.com) given in SAN attribute, it throws me the below mentioned error. <Certificate chain received from XYZ.com failed hostname verification check. Certificate contained abc.com but check expected XYZ.com> If we have more DNS for an application, Do we need to generate cert for every single DNS?

    Read the article

  • Cisco ASA - Enable communication between same security level

    - by Conor
    I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

    Read the article

  • June 23, 1983: First Successful Test of the Domain Name System [Geek History]

    - by Jason Fitzpatrick
    Nearly 30 years ago the first Domain Name System (DNS) was tested and it changed the way we interacted with the internet. Nearly impossible to remember number addresses became easy to remember names. Without DNS you’d be browsing a web where numbered addresses pointed to numbered addresses. Google, for example, would look like http://209.85.148.105/ in your browser window. That’s assuming, of course, that a numbers-based web every gained enough traction to be popular enough to spawn a search giant like Google. How did this shift occur and what did we have before DNS? From Wikipedia: The practice of using a name as a simpler, more memorable abstraction of a host’s numerical address on a network dates back to the ARPANET era. Before the DNS was invented in 1983, each computer on the network retrieved a file called HOSTS.TXT from a computer at SRI. The HOSTS.TXT file mapped names to numerical addresses. A hosts file still exists on most modern operating systems by default and generally contains a mapping of the IP address 127.0.0.1 to “localhost”. Many operating systems use name resolution logic that allows the administrator to configure selection priorities for available name resolution methods. The rapid growth of the network made a centrally maintained, hand-crafted HOSTS.TXT file unsustainable; it became necessary to implement a more scalable system capable of automatically disseminating the requisite information. At the request of Jon Postel, Paul Mockapetris invented the Domain Name System in 1983 and wrote the first implementation. The original specifications were published by the Internet Engineering Task Force in RFC 882 and RFC 883, which were superseded in November 1987 by RFC 1034 and RFC 1035.Several additional Request for Comments have proposed various extensions to the core DNS protocols. Over the years it has been refined but the core of the system is essentially the same. When you type “google.com” into your web browser a DNS server is used to resolve that host name to the IP address of 209.85.148.105–making the web human-friendly in the process. Domain Name System History [Wikipedia via Wired] What is a Histogram, and How Can I Use it to Improve My Photos?How To Easily Access Your Home Network From Anywhere With DDNSHow To Recover After Your Email Password Is Compromised

    Read the article

  • ASP.NET Export to Excel and Word using VB.NET and C#

    In most ASP.NET web applications there is a need to export data. This is particularly useful if the information will be used for further analysis and archiving purposes offline. This tutorial will illustrate how you can export your data from your ASP.NET webpage example if it is coming from a MSSQL database to one of the most common file export formats in Windows MS Excel and MS Word.... DNS Configured Correctly? Test Your Internal DNS With Our Free DNS Advisor Tool From Infoblox.

    Read the article

  • About cdn architecture to route way

    - by Tony Lee
    Our web system, use the third-party cdn service. Assume that the user set the local dns with the googledns or opendns to visit our web sites, so cdn service will select the closest cdn proxy node. all right, but in fact the user's actual access position might outside there, cdn service may chose the one furthest away from the user node, so static resource access slower.. At present, my idea is if user local set dns server with googledns, and then first one we get the actual ip address of the user, tracerote to test a best routing lines, set up a cookie in user browser, and then set 302 header for response to jump to the which best cdn node. Whether the user's browser side traceroute tool can provide the best route decision-making ? Because we find that, once the user to set local dns server with the foreign network segment, for example : set dns with 8.8.8.8, so cdn routing will choose the foreign service node.

    Read the article

  • Enterprise Portal Issue with the Ax Demo VPCs

    - by ssmantha
    Microsoft’s Ax Demo VPC is basically configured for a static IP address 192.168.0.1, this is due to the fact that the VPC has Domain Controlller configured in it which requires a static IP. When we put this VPC on a network with a different subnet and change the IP you can observer that the site http://sharepoint and http://sharepoint/EP cease to function and show “Page Not Found” errors in the browser. This is mainly due to the DNS configuration which is not updated. Below is the screen shot of the changes that needs to be done to make the site functioning properly. Change the following entries in the Forward Lookup Zones of DNS management: These websites default, SharePoint and projectserver are all mapped to a single port in the IIS i.e. port number 80. These websites are recognised with host headers. These host headers are configured in DNS with incorrect IP address entries in DNS when you change the IP address of the VPC. Just change these values to point to the Local Loop Adapter (127.0.0.1) and change the DNS to point to this address in the TCP/IP properties as shown below: This will resolve the issue with the website rendering. Initially you may get time out errors while browsing these website. be patient and try again this would work.

    Read the article

  • Point an external domain to a shared hosting website

    - by dailgez004
    I bought a domain from a seller (GoDaddy), and wish to point it at a shared hosting website (ASmallOrange). Googling tells me it's fairly straightforward: Step 1: On the external domain's DNS, configure two NS records for the two nameservers of the hosting service. Step 2: Wait 2-48 hours. I'm puzzled because it can't be that simple. I've told the DNS where to look, but since it's shared hosting, the hosting service needs to know what site to point the domain to. And indeed, after I've performed the above steps, visiting the domain leads me to a generic message from the shared hosting service. Okay, so I have to configure the DNS on the hosting service, right? The service I use (ASmallOrange) uses cPanel. What I tried is to set up a Parked Domain for the externally bought domain; when I go into the Advanced DNS Zone Editor, sure enough, the DNS for the external domain shows up as something I can configure. Yet, visiting the externally registered domain still points me to the generic shared server page. I'm convinced I'm doing something wrong. Could someone debug my thought process? Or perhaps offer alternate solutions? Right now, I'm considering trying to set up a CNAME record on the external domain to point to the domain I registered through the shared host -- but I have a vague impression that this is bad practice.

    Read the article

  • Can SSL Wildcards have multiple/nested levels of wildcard?

    - by Don Faulkner
    I know that an SSL wildcard certificate (*.example.org) can be used to support many names under the domain (a.example.org, b.example.org, c.example.org). I also know that the * is only good for matching a single level of name. That is, *.example.org will not work on a.b.example.org. What if I used a certificate with the name ..example.org? I'd like to build a certificate with the following name configuration: CN=example.org subjectAltName=DNS:example.org, DNS:*.example.org, DNS:*.*.example.org, DNS:*.*.*.example.org I've tried building a few like this as self-signed certificates, but I've not had good results. For example, chrome tells me "Server's certificate does not match the URL." Is it possible to have nested wildcards in a certificate, or do the popular browsers not support this?

    Read the article

  • Title case in Notepad++?

    - by recursive
    Is there a way to convert a block of text to title case in Notepad++? It should turn asdf ASDF aSdF into Asdf Asdf Asdf I see upper case and lower case on the edit menu, but those aren't quite what I'm looking for.

    Read the article

  • Resources for improving your comprehension of recursion?

    - by Andrew M
    I know what recursion is (when a patten reoccurs within itself, typically a function that calls itself on one of its lines, after a breakout conditional... right?), and I can understand recursive functions if I study them closely. My problem is, when I see new examples, I'm always initially confused. If I see a loop, or a mapping, zipping, nesting, polymorphic calling, and so on, I know what's going just by looking at it. When I see recursive code, my thought process is usually 'wtf is this?' followed by 'oh it's recursive' followed by 'I guess it must work, if they say it does.' So do you have any tips/plans/resources for building up your skills in this area? Recursion is kind of a wierd concept so I'm thinking the way to tackle it may be equally wierd and inobvious.

    Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >