Search Results

Search found 6339 results on 254 pages for 'josh 24 2'.

Page 104/254 | < Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >

• Cannot ping host stale ARP cache?

  - by gkchicago

  I am having a strange issue with a Debian (Lenny/Linux 2.6.26-2-amd64) that has been driving me nuts. On some machines within my network I can ping the host in question just fine, other times I have to manually hard-code the ARP ethernet address for the IP in order to establish connectivity. I've finally worked it down to somehow involving ARP. I just found how to fix it in a way that made it work but I'm looking for help explaining this issue and also I don't trust my fix to be permanent.. My thought process has been the following but I just can't make any sense out of it: Could it be the card? (Intel 82555 rev 4) Could it be because there are two network cards? (Default route is eth0) Could it be because of the network aliases? Lenny? AMD x86_64? Argh.. Thank you for any insight you might have // Ping doesn't go thru [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. --- 192.168.135.101 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3014ms // Here's the ARP Table, sometimes the .151 address is good, sometimes it // also matches the Gateways MAC like .101 is doing right here. [gordon@ubuntu ~]$ cat /proc/net/arp IP address HW type Flags HW address Mask Device 192.168.135.15 0x1 0x2 00:0B:DB:2B:24:89 * eth0 192.168.135.151 0x1 0x2 00:0B:6A:3A:30:A6 * eth0 192.168.135.1 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 192.168.135.101 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 // Drop the bad arp table listing and set it manually based on /sbin/ifconfig [gordon@ubuntu ~]$ sudo arp -d 192.168.135.101 [gordon@ubuntu ~]$ sudo arp -s 192.168.135.101 00:0B:6A:3A:30:A6 // Ping starts going thru..?!? [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. 64 bytes from 192.168.135.101: icmp_seq=1 ttl=64 time=15.8 ms 64 bytes from 192.168.135.101: icmp_seq=2 ttl=64 time=15.9 ms 64 bytes from 192.168.135.101: icmp_seq=3 ttl=64 time=16.0 ms 64 bytes from 192.168.135.101: icmp_seq=4 ttl=64 time=15.9 ms --- 192.168.135.101 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3012ms rtt min/avg/max/mdev = 15.836/15.943/16.064/0.121 ms The following is my network config on this. gordon@db01:~$ /sbin/ifconfig eth0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.151 Bcast:192.168.135.255 Mask:255.255.255.0 inet6 addr: fe80::20b:6aff:fe3a:30a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15476725 errors:0 dropped:0 overruns:0 frame:0 TX packets:10030036 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18565307359 (17.2 GiB) TX bytes:3412098075 (3.1 GiB) eth0:0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.150 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:1 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.101 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth1 Link encap:Ethernet HWaddr 00:e0:81:2a:6e:d0 inet addr:10.10.62.1 Bcast:10.10.62.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe2a:6ed0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10233315 errors:0 dropped:0 overruns:0 frame:0 TX packets:19400286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1112500658 (1.0 GiB) TX bytes:27952809020 (26.0 GiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:387 errors:0 dropped:0 overruns:0 frame:0 TX packets:387 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:41314 (40.3 KiB) TX bytes:41314 (40.3 KiB) gordon@db01:~$ sudo mii-tool -v eth0 eth0: negotiated 100baseTx-FD, link ok product info: Intel 82555 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD gordon@db01:~$ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface localnet * 255.255.255.0 U 0 0 0 eth0 10.10.62.0 * 255.255.255.0 U 0 0 0 eth1 default 192.168.135.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Can't get network bridging to work

  - by Antonis Christofides

  I'm trying to make network bridging to work on a Debian squeeze (I'm experimenting in order to make a QEMU/KVM virtual machine that will be visible to the outside network as if it were a distinct machine). The problem is that when I type brctl addif br0 eth0 then I lose connectivity to the network until I type brctl delif br0 eth0. More specifically, here's how my machine looks like before I do anything (essentially eth0 is listening on 147.102.160.153): root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591848sec preferred_lft 604648sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever 3: wlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 4c:ed:de:8e:44:d7 brd ff:ff:ff:ff:ff:ff 4: vboxnet0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 0a:00:27:00:00:00 brd ff:ff:ff:ff:ff:ff 5: pan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether ee:7c:88:59:d0:e8 brd ff:ff:ff:ff:ff:ff Now let me add the bridge: root@laura:/home/anthony# brctl addbr br0 root@laura:/home/anthony# ip tuntap add dev tap0 mode tap root@laura:/home/anthony# ip link set tap0 up root@laura:/home/anthony# brctl addif br0 tap0 Until here everything continues to work normally. Finally, I try to add eth0 to the bridge: root@laura:/home/anthony# brctl addif br0 eth0 At this point, I no longer have a network connection. If I try to ping something, it tells "Destination Host Unreachable". The output of ip addr show seems normal: root@laura:/home/anthony# ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether 8c:73:6e:db:1c:1b brd ff:ff:ff:ff:ff:ff inet 147.102.160.153/24 brd 147.102.160.255 scope global eth0 inet6 2001:648:2000:a0:8e73:6eff:fedb:1c1b/64 scope global dynamic valid_lft 2591908sec preferred_lft 604708sec inet6 fe80::8e73:6eff:fedb:1c1b/64 scope link valid_lft forever preferred_lft forever [snip wlan0, vboxnet0 and pan0, which are down and irrelevant] 8: br0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff 9: tap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 500 link/ether 16:30:f2:67:ab:75 brd ff:ff:ff:ff:ff:ff inet6 fe80::1430:f2ff:fe67:ab75/64 scope link valid_lft forever preferred_lft forever Also: root@laura:/home/anthony# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 147.102.160.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 0.0.0.0 147.102.160.200 0.0.0.0 UG 0 0 0 eth0 I can't understand what I'm doing wrong. I want the machine to continue to listen on 147.102.160.153 on eth0, and in addition to that I want to have a tap0 interface, bridged to eth0, that will be available to the guest machine so that the latter listens on another ip address (say 147.102.160.205). (If there's another way to achieve what I want, I'm also interested.)

  Read the article

• What is consuming so much memory?

  - by Christopher

  Hi, I am having a few problems with my server. It is throwing up intermittant errors and running quite slow. Here is the output from top: top - 07:33:33 up 18:57, 1 user, load average: 0.00, 0.00, 0.00 Tasks: 90 total, 1 running, 82 sleeping, 7 stopped, 0 zombie Cpu(s): 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1048576k total, 1048576k used, 0k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached Ordered by %MEM: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 9597 root 16 0 276m 91m 15m S 0.0 8.9 0:29.38 java 9564 tomcat 15 0 249m 34m 11m S 0.0 3.4 0:11.79 java 9636 root 18 0 54804 24m 9784 S 0.0 2.4 0:02.58 httpd 26139 apache 15 0 57520 23m 5996 S 0.0 2.3 0:00.15 httpd 16264 apache 18 0 56984 23m 6104 S 0.0 2.2 0:00.21 httpd 24294 apache 15 0 57512 22m 5864 S 0.0 2.2 0:00.17 httpd 30231 apache 15 0 57272 22m 5748 S 0.0 2.2 0:00.97 httpd 32257 apache 15 0 57512 22m 5416 S 0.0 2.2 0:00.46 httpd 19947 apache 15 0 57512 22m 5320 S 0.0 2.2 0:00.19 httpd 26148 apache 15 0 56688 22m 5992 S 0.0 2.2 0:00.40 httpd 14039 apache 18 0 57000 22m 5492 S 0.0 2.2 0:00.33 httpd 6051 apache 15 0 57736 22m 5128 S 0.0 2.2 0:00.07 httpd 19937 apache 15 0 56992 22m 5400 S 0.0 2.2 0:00.14 httpd 5200 apache 15 0 56984 22m 5376 S 0.0 2.2 0:00.23 httpd 10001 apache 15 0 55636 21m 5636 S 0.0 2.1 0:01.05 httpd 11734 apache 15 0 56712 21m 4548 S 0.0 2.1 0:00.46 httpd 18193 apache 15 0 55100 20m 5508 S 0.0 2.0 0:00.24 httpd 14036 apache 15 0 55128 20m 5412 S 0.0 2.0 0:00.10 httpd 3981 apache 15 0 55128 19m 4860 S 0.0 1.9 0:00.16 httpd 7588 apache 18 0 55112 19m 4848 S 0.0 1.9 0:00.04 httpd 19768 apache 16 0 55112 19m 4844 S 0.0 1.9 0:00.02 httpd 5827 apache 15 0 55112 19m 4828 S 0.0 1.9 0:00.05 httpd 29774 apache 15 0 55112 19m 4544 S 0.0 1.9 0:00.11 httpd 6064 apache 15 0 55112 19m 4536 S 0.0 1.9 0:00.02 httpd 16253 apache 17 0 55116 19m 4532 S 0.0 1.9 0:00.01 httpd 19922 apache 15 0 55112 19m 4540 S 0.0 1.9 0:00.02 httpd 10010 apache 15 0 55100 19m 4524 S 0.0 1.9 0:00.01 httpd 18195 apache 18 0 55104 18m 3872 S 0.0 1.8 0:00.02 httpd 7361 mysql 15 0 134m 18m 6400 S 0.0 1.8 0:10.18 mysqld 19921 apache 15 0 55088 18m 3588 S 0.0 1.8 0:00.02 httpd 11967 apache 15 0 55080 18m 3584 S 0.0 1.8 0:00.00 httpd 13813 apache 15 0 55088 18m 3576 S 0.0 1.8 0:00.14 httpd 23898 apache 18 0 54968 17m 3212 S 0.0 1.7 0:00.00 httpd 13792 apache 15 0 54968 17m 3088 S 0.0 1.7 0:00.00 httpd 14083 apache 15 0 54968 17m 3088 S 0.0 1.7 0:00.00 httpd 32547 apache 15 0 54944 17m 2924 S 0.0 1.7 0:00.00 httpd 13787 apache 15 0 54944 17m 2908 S 0.0 1.7 0:00.00 httpd 3623 apache 17 0 54944 17m 2908 S 0.0 1.7 0:00.00 httpd 16024 apache 19 0 54944 17m 2860 S 0.0 1.7 0:00.00 httpd 13791 apache 15 0 54944 17m 2864 S 0.0 1.7 0:00.00 httpd 20090 named 19 0 110m 4244 2056 S 0.0 0.4 0:01.55 named 9369 cyrus 15 0 15904 3048 1720 S 0.0 0.3 0:00.24 cyrus-master 32735 root 15 0 8852 2888 2116 T 0.0 0.3 0:00.00 mysql The intermittant error I get using Firefox is: Server not found Firefox can't find the server at XXXXXXX.co. * Check the address for typing errors such as ww.example.com instead of www.example.com * If you are unable to load any pages, check your computer's network connection. * If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. And on other browsers, the page just loads for about 10 minutes but never appears. The only way to resolve it is to close the browser completely as the error appears to be saved in the cache. Has anyone got any ideas? Many Thanks.

  Read the article

• High Load mysql on Debian server

  - by Oleg Abrazhaev

  I have Debian server with 32 gb memory. And there is apache2, memcached and nginx on this server. Memory load always on maximum. Only 500m free. Most memory leak do MySql. Apache only 70 clients configured, other services small memory usage. When mysql use all memory it stops. And nothing works, need mysql reboot. Mysql configured use maximum 24 gb memory. I have hight weight InnoDB bases. (400000 rows, 30 gb). And on server multithread daemon, that makes many inserts in this tables, thats why InnoDB. There is my mysql config. [mysqld] # # * Basic Settings # default-time-zone = "+04:00" user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking default-time-zone='Europe/Moscow' # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. # # * Fine Tuning # #low_priority_updates = 1 concurrent_insert = ALWAYS wait_timeout = 600 interactive_timeout = 600 #normal key_buffer_size = 2024M #key_buffer_size = 1512M #70% hot cache key_cache_division_limit= 70 #16-32 max_allowed_packet = 32M #1-16M thread_stack = 8M #40-50 thread_cache_size = 50 #orderby groupby sort sort_buffer_size = 64M #same myisam_sort_buffer_size = 400M #temp table creates when group_by tmp_table_size = 3000M #tables in memory max_heap_table_size = 3000M #on disk open_files_limit = 10000 table_cache = 10000 join_buffer_size = 5M # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #myisam_use_mmap = 1 max_connections = 200 thread_concurrency = 8 # # * Query Cache Configuration # #more ignored query_cache_limit = 50M query_cache_size = 210M #on query cache query_cache_type = 1 # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. #log = /var/log/mysql/mysql.log # # Error logging goes to syslog. This is a Debian improvement :) # # Here you can see queries with especially long duration log_slow_queries = /var/log/mysql/mysql-slow.log long_query_time = 1 log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log server-id = 1 log-bin = /var/lib/mysql/mysql-bin #replicate-do-db = gate log-bin-index = /var/lib/mysql/mysql-bin.index log-error = /var/lib/mysql/mysql-bin.err relay-log = /var/lib/mysql/relay-bin relay-log-info-file = /var/lib/mysql/relay-bin.info relay-log-index = /var/lib/mysql/relay-bin.index binlog_do_db = 24avia expire_logs_days = 10 max_binlog_size = 100M read_buffer_size = 4024288 innodb_buffer_pool_size = 5000M innodb_flush_log_at_trx_commit = 2 innodb_thread_concurrency = 8 table_definition_cache = 2000 group_concat_max_len = 16M #binlog_do_db = gate #binlog_ignore_db = include_database_name # # * BerkeleyDB # # Using BerkeleyDB is now discouraged as its support will cease in 5.1.12. #skip-bdb # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # You might want to disable InnoDB to shrink the mysqld process by circa 100MB. #skip-innodb # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 500M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 32M key_buffer_size = 512M # # * NDB Cluster # # See /usr/share/doc/mysql-server-*/README.Debian for more information. # # The following configuration is read by the NDB Data Nodes (ndbd processes) # not from the NDB Management Nodes (ndb_mgmd processes). # # [MYSQL_CLUSTER] # ndb-connectstring=127.0.0.1 # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ Please, help me make it stable. Memory used /etc/mysql # free total used free shared buffers cached Mem: 32930800 32766424 164376 0 139208 23829196 -/+ buffers/cache: 8798020 24132780 Swap: 33553328 44660 33508668 Maybe my problem not in memory, but MySQL stops every day. As you can see, cache memory free 24 gb. Thank to Michael Hampton? for correction. Load overage on server 3.5. Maybe hdd or another problem? Maybe my config not optimal for 30gb InnoDB ?

  Read the article

• dvd drive I/O error?

  - by bobby

  i get dis error evry time i burn a cd/dvd thru my dvd drive...!! Nero Burning ROM bobby 4C85-200E-4005-0004-0000-7660-0800-35X3-0000-407M-MX37-**** (*) Windows XP 6.1 IA32 WinAspi: - NT-SPTI used Nero Version: 7.11.3. Internal Version: 7, 11, 3, (Nero Express) Recorder: Version: UL01 - HA 1 TA 1 - 7.11.3.0 Adapter driver: HA 1 Drive buffer : 2048kB Bus Type : default CD-ROM: Version: 52PP - HA 1 TA 0 - 7.11.3.0 Adapter driver: HA 1 === Scsi-Device-Map === === CDRom-Device-Map === ATAPI-CD ROM-DRIVE-52MAX F: CdRom0 HL-DT-ST DVDRAM GSA-H12N G: CdRom1 ======================= AutoRun : 1 Excluded drive IDs: WriteBufferSize: 83886080 (0) Byte BUFE : 0 Physical memory : 958MB (981560kB) Free physical memory: 309MB (317024kB) Memory in use : 67 % Uncached PFiles: 0x0 Use Inquiry : 1 Global Bus Type: default (0) Check supported media : Disabled (0) 11.6.2010 CD Image 10:43:02 AM #1 Text 0 File SCSIPTICommands.cpp, Line 450 LockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL 10:43:02 AM #2 Text 0 File Burncd.cpp, Line 3186 HL-DT-ST DVDRAM GSA-H12N Buffer underrun protection activated 10:43:02 AM #3 Text 0 File Burncd.cpp, Line 3500 Turn on Disc-At-Once, using CD-R/RW media 10:43:02 AM #4 Text 0 File DlgWaitCD.cpp, Line 307 Last possible write address on media: 359848 ( 79:59.73) Last address to be written: 318783 ( 70:52.33) 10:43:02 AM #5 Text 0 File DlgWaitCD.cpp, Line 319 Write in overburning mode: NO (enabled: CD) 10:43:02 AM #6 Text 0 File DlgWaitCD.cpp, Line 2988 Recorder: HL-DT-ST DVDRAM G SA-H12N; CDR co de: 00 97 27 18; O SJ entry from: Pla smon Data systems Ltd. ATIP Data: Special Info [hex] 1: D0 00 A0, 2: 61 1B 12 (LI 97:27.18), 3: 4F 3B 4A ( LO 79:59.74) Additional Info [hex] 1: 00 00 00 (invalid), 2: 00 00 00 (invalid), 3: 00 0 0 00 (invalid) 10:43:02 AM #7 Text 0 File DlgWaitCD.cpp, Line 493 Protocol of DlgWaitCD activities: TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 318784 blo cks [G: HL-DT-ST DVDRAM GSA-H12N] -------------------------------------------------------------- 10:43:02 AM #9 Text 0 File ThreadedTransferInterface.cpp, Line 986 Prepare [G: HL-DT-ST DVDRAM GSA-H12N] for write in CUE-sheet-DAO DAO infos: ========== MCN: "" TOCType: 0x00; Se ssion Clo sed, disc fixated Tracks 1 to 1: Idx 0 Idx 1 Next T rk 1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 6531768 32, ISRC "" DAO layout: =========== ___Start_|____Track_|_Idx_|_CtrlAdr_|_____Size_|______NWA_|_RecDep__________ -150 | lead-in | 0 | 0x41 | 0 | 0 | 0x00 -150 | 1 | 0 | 0x41 | 0 | 0 | 0x00 0 | 1 | 1 | 0x41 | 318784 | 318784 | 0x00 318784 | lead-out | 1 | 0x41 | 0 | 0 | 0x00 10:43:02 AM #10 Text 0 File SCSIPTICommands.cpp, Line 240 SPTILockVolume - completed successfully for FSCTL_LOCK_VOLUME 10:43:02 AM #11 Text 0 File Burncd.cpp, Line 4286 Caching options: cache CDRom or Network-Yes, small files-Yes ( ON 10:43:03 AM #19 Text 0 File MMC.cpp, Line 18034 CueData, Len=32 41 00 00 14 00 00 00 00 41 01 00 10 00 00 00 00 41 01 01 10 00 00 02 00 41 aa 01 14 00 46 34 22 10:43:03 AM #20 Text 0 File ThreadedTransfer.cpp, Line 268 Pipe memory size 83836800 10:43:16 AM #21 Text 0 File Cdrdrv.cpp, Line 1405 10:43:16.806 - G: HL-DT-ST DVDRAM GSA-H12N : Queue again later 10:43:42 AM #22 SPTI -1502 File SCSIPassThrough.cpp, Line 181 CdRom1: SCSIStatus(x02) WinError(0) NeroError(-1502) Sense Key: 0x04 (KEY_HARDWARE_ERROR) Nero Report 2 Nero Burning ROM Sense Code: 0x08 Sense Qual: 0x03 CDB Data: 0x2A 00 00 00 4D 00 00 00 20 00 00 00 Sense Area: 0x70 00 04 00 00 00 00 10 53 29 A1 80 08 03 Buffer x0c7d9a40: Len x10000 0xDC 87 EB 41 6E AC 61 5A 07 B2 DB 78 B5 D4 D9 24 0x8D BC 51 38 46 56 0F EE 16 15 5C 5B E3 B0 10 16 0x14 B1 C3 6E 30 2B C4 78 15 AB D5 92 09 B7 81 23 10:43:42 AM #23 CDR -1502 File Writer.cpp, Line 306 DMA-driver error, CRC error G: HL-DT-ST DVDRAM GSA-H12N 10:43:55 AM #24 Phase 38 File dlgbrnst.cpp, Line 1767 Burn process failed at 48x (7,200 KB/s) 10:43:55 AM #25 Text 0 File SCSIPTICommands.cpp, Line 287 SPTIDismountVolume - completed successfully for FSCTL_DISMOUNT_VOLUME 10:44:01 AM #26 Text 0 File Cdrdrv.cpp, Line 11412 DriveLocker: UnLockVolume completed 10:44:01 AM #27 Text 0 File SCSIPTICommands.cpp, Line 450 UnLockMCN - completed sucessfully for IOCTL_STORAGE_MCN_CONTROL Existing drivers: Registry Keys: HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon Nero Report 3

  Read the article

• xrandr shows two displays (LVDS1), but how can I use VGA1 only?

  - by Tom Fishman

  We're running Ubuntu 11 on this hardware: Foxconn R20-D2 Intel Atom D510 Intel NM10 Intel GMA 3150 Barebone There is no integrated display (it is a barebone box). I connected an external VGA to it. However xrandr shows two displays: Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 LVDS1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0*+ 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 519mm x 324mm 1920x1200 60.0 + 1600x1200 60.0 1680x1050 60.0 1280x1024 76.0 75.0 72.0 60.0 1440x900 75.0 59.9 1152x864 75.0 1024x768 75.1 70.1 60.0* 832x624 74.6 800x600 72.2 75.0 60.3 640x480 72.8 75.0 66.7 60.0 720x400 70.1 But I don't have two displays. How can I get rid of LVDS1 and use only VGA1? The direct result is that I'm seeing a 1024x768 resolution on my VGA display, because the OS is using "mirror" mode which uses the lower resolution of the two. Turning off the mirror is not a solution. I want to fix it. Related logs: ... [ 20.019] (II) intel(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 20.019] (==) intel(0): Depth 24, (--) framebuffer bpp 32 [ 20.019] (==) intel(0): RGB weight 888 [ 20.019] (==) intel(0): Default visual is TrueColor [ 20.019] (II) intel(0): Integrated Graphics Chipset: Intel(R) Pineview G [ 20.019] (--) intel(0): Chipset: "Pineview G" [ 20.019] (**) intel(0): Relaxed fencing enabled [ 20.019] (**) intel(0): Wait on SwapBuffers? enabled [ 20.019] (**) intel(0): Triple buffering? enabled [ 20.019] (**) intel(0): Framebuffer tiled [ 20.019] (**) intel(0): Pixmaps tiled [ 20.020] (**) intel(0): 3D buffers tiled [ 20.020] (**) intel(0): SwapBuffers wait enabled [ 20.020] (==) intel(0): video overlay key set to 0x101fe [ 20.020] (II) intel(0): Output LVDS1 has no monitor section [ 20.020] (II) intel(0): found backlight control interface /sys/class/backlight/intel_backlight [ 20.080] (II) intel(0): Output VGA1 has no monitor section [ 20.080] (II) intel(0): EDID for output LVDS1 [ 20.081] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported) [ 20.081] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported) ... [ 20.082] (II) intel(0): Not using default mode "960x600" (doublescan mode not supported) [ 20.082] (II) intel(0): Printing probed modes for output LVDS1 [ 20.082] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) [ 20.082] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) [ 20.082] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz) [ 20.082] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) [ 20.149] (II) intel(0): EDID for output VGA1 [ 20.149] (II) intel(0): Manufacturer: BNQ Model: 771b Serial#: 6595 [ 20.149] (II) intel(0): Year: 2008 Week: 16 [ 20.149] (II) intel(0): EDID Version: 1.3 [ 20.149] (II) intel(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V ... [ 20.152] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz) [ 20.152] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz) [ 20.152] (II) intel(0): Output LVDS1 connected [ 20.152] (II) intel(0): Output VGA1 connected [ 20.152] (II) intel(0): Using exact sizes for initial modes [ 20.152] (II) intel(0): Output LVDS1 using initial mode 1024x768 [ 20.152] (II) intel(0): Output VGA1 using initial mode 1024x768 [ 20.152] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. ...

  Read the article

• Blank black screen with cursor after login -- RHEL5

  - by Sean O.

  I have a RHEL 5 machine here which is a Dell Precision T3500. I'm an Ubuntu guy, but I'm having a heck of a time with this machine. After processing its first security update, we cannot log in via the gdm greeter. A new kernel was installed; then I installed the nVidia drivers for our Quadro NVS 295. I know the X configuration is valid because the gdm greeter does display; however, upon login all we can get is a blank, black screen with a cursor. I thought perhaps our python installation was corrupted but a reinstall via yum has not helped. I have searched & googled extensively for a potential fix for this and can find nothing. Below are outputs from uname, a tail of an error in /var/log/messages, and the Xorg.conf. Can anyone suggest a course of action? [sean@cheetah ~]$ uname -a Linux cheetah.*.* 2.6.18-308.8.1.el5 #1 SMP Fri May 4 16:43:02 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux [sean@cheetah ~]$ sudo tail /var/log/messages Jun 5 15:03:04 cheetah gconfd (sean-4592): Resolved address "xml:readonly:/etc/gconf/gconf.xml.defaults" to a read-only configuration source at position 2 Jun 5 15:03:05 cheetah hcid[3855]: Default passkey agent (:1.8, /org/bluez/applet) registered Jun 5 15:03:05 cheetah pcscd: winscard.c:304:SCardConnect() Reader E-Gate 0 0 Not Found Jun 5 15:03:05 cheetah last message repeated 2 times Jun 5 15:03:06 cheetah gconfd (sean-4592): Resolved address "xml:readwrite:/home/sean/.gconf" to a writable configuration source at position 0 Jun 5 15:03:06 cheetah setroubleshoot: [program.ERROR] exception ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Traceback (most recent call last): File "/usr/bin/sealert", line 952, in ? from setroubleshoot.gui_utils import * File "/usr/lib/python2.4/site-packages/setroubleshoot/gui_utils.py", line 26, in ? import gtk File "/usr/lib64/python2.4/site-packages/gtk-2.0/gtk/__init__.py", line 48, in ? from gtk import _gtk ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Jun 5 15:03:07 cheetah setroubleshoot: [program.ERROR] exception ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Traceback (most recent call last): File "/usr/bin/sealert", line 952, in ? from setroubleshoot.gui_utils import * File "/usr/lib/python2.4/site-packages/setroubleshoot/gui_utils.py", line 26, in ? import gtk File "/usr/lib64/python2.4/site-packages/gtk-2.0/gtk/__init__.py", line 48, in ? from gtk import _gtk ImportError: /usr/lib/libatk-1.0.so.0: undefined symbol: g_assertion_message_expr Jun 5 15:03:08 cheetah pcscd: winscard.c:304:SCardConnect() Reader E-Gate 0 0 Not Found Jun 5 15:07:01 cheetah ntpd[4114]: synchronized to 64.16.211.38, stratum 3 Jun 5 15:07:01 cheetah ntpd[4114]: kernel time sync enabled 0001 [sean@cheetah ~]$ cat /etc/X11/xorg.conf # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 295.53 ([email protected]) Sat May 12 00:34:20 PDT 2012 # Xorg configuration created by system-config-display Section "ServerLayout" Identifier "single head configuration" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" Option "XkbModel" "pc105" Option "XkbLayout" "us" EndSection Section "Monitor" ### Comment all HorizSync and VertSync values to use DDC: ### Comment all HorizSync and VertSync values to use DDC: Identifier "Monitor0" ModelName "LCD Panel 1600x1200" HorizSync 31.5 - 74.7 VertRefresh 56.0 - 65.0 Option "dpms" EndSection Section "Device" Identifier "Videocard0" Driver "nvidia" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection

  Read the article

• Dhcpd Daemon is trying to lease itself?

  - by tommieb75

  I have a Slackware Linux 13.0 box with two interfaces, eth0 and eth1. I have set this box up to be on the 192.168.1.0/24 network, with subnet mask of 255.255.255.0. I am trying to run a dhcpd server on this box to service two interfaces above, so I subnetted the 192.168.1.0/24 network into two subnets. For eth0 192.168.1.1, subnet mask 255.255.255.128, broadcast mask 192.168.1.127. For eth1 192.168.1.129, subnet mask 255.255.255.128, broadcast mask 192.168.1.255. Both the interfaces are assigned manually. eth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.1 Bcast:192.168.1.127 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:39 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:1404 (1.3 KiB) Interrupt:11 Base address:0x8000 Memory:faffc000-faffcfff eth1 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.1.128 Bcast:192.168.1.255 Mask:255.255.255.128 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10003 errors:0 dropped:0 overruns:0 frame:0 TX packets:13286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1589229 (1.5 MiB) TX bytes:9900005 (9.4 MiB) Interrupt:11 Here is the dhcpd.conf set up authoritative; ddns-update-style interim; ignore client-updates; subnet 192.168.1.0 netmask 255.255.255.128 { range 192.168.1.2 192.168.1.126; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.127; option subnet-mask 255.255.255.128; } subnet 192.168.1.128 netmask 255.255.255.128 { range 192.168.1.129 192.168.1.254; default-lease-time 86400; max-lease-time 86400; option routers 192.168.1.1; option ip-forwarding off; option domain-name-servers 208.67.222.222, 208.67.220.220; option broadcast-address 192.168.1.255; option subnet-mask 255.255.255.128; } This is what is showing in the log Apr 10 18:09:58 inspiron8600 dhcpd: DHCPDISCOVER from 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:09:58 inspiron8600 dhcpd: DHCPOFFER on 192.168.1.131 to 00:00:00:00:00:00 (inspiron8600) via eth1 Apr 10 18:10:01 inspiron8600 dhcpcd[3832]: eth1: adding IP address 169.254.153.6/16 This is happening spuriously, and the log gets filled up with nonsense..so my question is this: How do I stop this from happening? And why would it be trying to give itself a lease? I am sure I have missed something but cannot see it and would appreciate a pair of eyes from the community to spot the obvious flaw!

  Read the article

• Riak "error":"insufficient_vnodes_available"

  - by Wolfiem

  We have 4 nodes Riak installation. They are running on Ubuntu 12.04 LTS Precise installed servers. We have installed 1.1.4 at August 1st 2012 and upgraded 1.2.0 when its available. Server names are: f1 - 10.10.0.12 - This is the first installed server. We have joined other ones to this server. This also serves Riak control. s2 - 10.10.0.22 - s3 - 10.10.0.23 - s4 - 10.10.0.24 - This server also serves Riak control. This morning we've seen "insufficient nodes available" error at our applications log and restarted all nodes. 3 of them became available except "f1" UPDATE : while I prepare this message live 3 nodes became unavailable and need restart Riak. wolfiem@f01:~$ sudo /etc/init.d/riak start Riak failed to start within 15 seconds, see the output of 'riak console' for more information. If you want to wait longer, set the environment variable WAIT_FOR_ERLANG to the number of seconds to wait. I've tried to set WAIT_FOR_ERLANG value to 60 seconds but I can't. adding this line in vm.args didn't work: -env WAIT_FOR_ERLANG 60 I also tried to set this from terminal but it didn't work either. wolfiem@f01:~$ export WAIT_FOR_ERLANG=60 It still says "Riak failed to start within 15 seconds" This is the console.log output: 2012-09-11 10:58:02.532 [info] <0.7.0> Application lager started on node '[email protected]' 2012-09-11 10:58:02.560 [warning] <0.148.0>@riak_core_ring_manager:reload_ring:231 No ring file available. 2012-09-11 10:58:02.585 [error] <0.164.0> CRASH REPORT Process <0.164.0> with 0 neighbours exited with reason: eaddrnotavail in gen_server:init_it/6 line 320 This is the error.log output 2012-09-11 10:58:02.585 [error] <0.164.0> CRASH REPORT Process <0.164.0> with 0 neighbours exited with reason: eaddrnotavail in gen_server:init_it/6 line 320 This is the crash.log output: 2012-09-11 10:58:02 =CRASH REPORT==== crasher: initial call: mochiweb_socket_server:init/1 pid: <0.164.0> registered_name: [] exception exit: {eaddrnotavail,[{gen_server,init_it,6,[{file,"gen_server.erl"},{line,320}]},{proc_lib,init_p_do_apply,3,[{file,"proc_lib.erl"},{line,227}]}]} ancestors: [riak_core_sup,<0.135.0>] messages: [] links: [<0.136.0>] dictionary: [] trap_exit: true status: running heap_size: 377 stack_size: 24 reductions: 403 neighbours: You can find the riak console output below: wolfiem@f01:~$ riak console Attempting to restart script through sudo -H -u riak Exec: /usr/lib/riak/erts-5.9.1/bin/erlexec -boot /usr/lib/riak/releases/1.2.0/riak -embedded -config /etc/riak/app.config -pa /usr/lib/riak/basho-patches -args_file /etc/riak/vm.args -- console Root: /usr/lib/riak Erlang R15B01 (erts-5.9.1) [source] [64-bit] [smp:8:8] [async-threads:64] [kernel-poll:true] =INFO REPORT==== 11-Sep-2012::10:44:18 === alarm_handler: {set,{system_memory_high_watermark,[]}} ** /usr/lib/riak/lib/observer-1.1/ebin/etop_txt.beam hides /usr/lib/riak/lib/basho-patches/etop_txt.beam ** Found 1 name clashes in code paths 10:44:19.099 [info] Application lager started on node '[email protected]' 10:44:19.130 [warning] No ring file available. 10:44:19.158 [error] CRASH REPORT Process <0.164.0> with 0 neighbours exited with reason: eaddrnotavail in gen_server:init_it/6 line 320 /usr/lib/riak/lib/os_mon-2.2.9/priv/bin/memsup: Erlang has closed. =INFO REPORT==== 11-Sep-2012::10:44:19 === alarm_handler: {clear,system_memory_high_watermark} Erlang has closed {"Kernel pid terminated",application_controller,"{application_start_failure,riak_core,{shutdown,{riak_core_app,start,[normal,[]]}}}"} Crash dump was written to: /var/log/riak/erl_crash.dump Kernel pid terminated (application_controller) ({application_start_failure,riak_core,{shutdown,{riak_core_app,start,[normal,[]]}}})

  Read the article

• WDS DHCP same server on Windows Server 2008

  - by Richard

  I have been struggling with a problem on my Windows Server 2008 for the past 4 - 5 hours and cannot figure out whats wrong. I have tried pretty much everything that I found on google and all the links are purple. Hopefully you guys can help me. I am running a Windows Server 2008 Standard edition with the latest updates as of today. Furthermore I am running a Windows Server 2003. Both are virtual machines on my ESXi 5 server. My network is: 192.168.10.0/24 W2k8: 192.168.10.251 is the PDC running ADS, DHCP and WDS W2k3: 192.168.10.253 AND 192.168.1.175 running Routing and Remote Access and ISA 2006 Enterprise In my internal network (192.168.10.0/24) I have my client machine (192.168.10.10) that runs a VMWare Workstation. I am trying to deploy Windows 7 Home Premium to a virtual machine on my VMWorkstation via PXE. I have set the Workstation's VM network adapter to "bridged" so that it uses the physical network adapter and is connected to my internal network. The DHCP pool is configured to give IP addresses from 192.168.10.10-192.168.10.15 (works for normal clients and is not used up) When I start my VM with the PXE I get the error: PXE-E52:proxyDHCP offers were received. No DHCP offers were received Apperently this means "that means that WDS responded but the DHCP server did not." People suggested to direct the traffic to both WDS and DHCP on the router, since everything is on the same subnet there is no need for that as the broadcast is seen by everyone (WDS and DHCP) No reservation for the virtual mac addrs is made on the DHCP. Furthermore it was suggested to configure the DHCP options: Option 60= PXEClient Option 66= WDS server name or IP address Option 67= Boot file name However, this is not recommended by Microsoft, I tried it and it did not solve my problem. The configuration on the WDS (My System is German therefore the actual naming might be different): PXE response tab: PXE responses is set to "ALL (known and unknown)" DHCP Tab: Do not listen to port 67 is NOT ticked - if I tick this I do not get any responses and the PXE errors gets PXE-E51 that neither DHCP or proxyDHCP were received DHCP-Option 60 for "PXEClient" is ticked The confusing part here is that it is advised in the tab to tick the first option since it is on the same server. Network Configuration Tab: Use the following IP-Address range for Multicast-IP-Address: 224.0.1.0 - 224.0.10.0 Thats not the default one, however it is in the allowed range. The UDP port range is the default since it is not advised to change them. I tried to change the "networkprofile" from 100mbits/1gbits and custom. I am running a 1gbit network with CAT6 cables and 1gbit netgear switch 5 ports. Everything is configured to use 1gbit. The WDS is authorised for the DHCP server. My ISA 2006 configuration: For the internal networking i have configured the following policy array: Allow protocols on internal network including the w2k3 host: 67,68,53,ICMP, 4011 UDP receive, 64001-6500 UDP send receive, 69 UDP send Routing and Remote Access I tried the DHCP relay agent configuration that was suggested as well, but that did not work I would highly appreciate anykind of help because I am pretty much done here with my nerves. Thank you very much in advance.

  Read the article

• Troubleshooting High Load on Plesk LAMP Dedicated Server

  - by Callmeed

  I have 2 nearly identical dedicated servers with the same provider. They also run a nearly identical software stack: RedHat 5 64-bit, Plesk, PHP, Apache, & MySQL. We use them for hosting custom sites we build. The problem is, while our 1st server has a load average (in top) of around 0.3, the 2nd server consistently has a load average of around 4.0 or higher. Basic functions in Plesk are delayed and there is a bit of latency when executing shell commands. Anyone have ideas why it would be so high? And why it would differ from our other server so much? Here is my current top output (sorted by %MEM) ... Any help is much appreciated ... top - 21:48:04 up 100 days, 4:28, 1 user, load average: 3.74, 4.20, 4.23 Tasks: 336 total, 1 running, 335 sleeping, 0 stopped, 0 zombie Cpu(s): 0.8%us, 0.4%sy, 0.0%ni, 91.3%id, 7.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 12290884k total, 11886452k used, 404432k free, 2920212k buffers Swap: 2096472k total, 244k used, 2096228k free, 6560692k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22536 apache 15 0 860m 547m 6484 S 0.0 4.6 0:10.96 httpd 26467 apache 15 0 859m 546m 6408 S 0.0 4.5 0:07.67 httpd 3620 apache 15 0 859m 545m 5552 S 0.0 4.5 0:06.15 httpd 1895 apache 15 0 858m 544m 6356 S 0.0 4.5 0:08.25 httpd 16933 apache 15 0 858m 544m 5488 S 0.0 4.5 0:01.57 httpd 6431 apache 15 0 856m 542m 6076 S 10.6 4.5 0:05.32 httpd 14417 apache 15 0 856m 542m 5568 S 0.0 4.5 0:03.88 httpd 15403 apache 15 0 855m 541m 5616 S 0.0 4.5 0:03.73 httpd 19165 apache 15 0 853m 539m 6252 S 0.0 4.5 0:12.40 httpd 15898 apache 15 0 852m 539m 5376 S 0.0 4.5 0:02.68 httpd 14401 apache 15 0 851m 538m 5460 S 0.0 4.5 0:02.97 httpd 15393 apache 15 0 851m 538m 5404 S 0.0 4.5 0:03.12 httpd 15427 apache 15 0 851m 538m 5496 S 0.0 4.5 0:02.44 httpd 14412 apache 15 0 851m 538m 5324 S 0.0 4.5 0:02.15 httpd 18330 apache 15 0 851m 537m 5136 S 0.0 4.5 0:01.30 httpd 18303 apache 15 0 848m 535m 5140 S 0.0 4.5 0:00.47 httpd 21190 apache 15 0 845m 533m 3988 S 0.0 4.4 0:00.33 httpd 15923 root 18 0 822m 521m 9928 S 0.0 4.3 10:04.81 httpd 22021 apache 15 0 828m 520m 4964 S 0.0 4.3 0:00.16 httpd 22146 apache 15 0 823m 515m 3016 S 0.0 4.3 0:00.02 httpd 22345 apache 15 0 822m 514m 2408 S 0.0 4.3 0:00.00 httpd 14721 apache 15 0 733m 510m 488 S 0.0 4.3 0:00.00 httpd 5094 root 15 0 1452m 122m 15m S 1.0 1.0 852:24.24 java 4636 mysql 15 0 532m 57m 6440 S 1.0 0.5 488:05.84 mysqld 4799 popuser 15 0 166m 53m 2368 S 0.0 0.4 0:36.64 spamd 16761 popuser 15 0 159m 46m 2312 S 0.0 0.4 0:00.38 spamd 4797 root 15 0 158m 45m 2448 S 0.0 0.4 0:01.27 spamd 5074 root 34 19 255m 20m 2144 S 0.0 0.2 1:37.53 yum-updatesd 9917 named 15 0 366m 9804 1980 S 0.0 0.1 0:10.26 named 4332 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.06 sw-engine-cgi 4341 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.07 sw-engine-cgi 4350 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.09 sw-engine-cgi 4352 sso 18 0 119m 8028 5212 S 0.0 0.1 0:00.11 sw-engine-cgi 4376 ntp 15 0 23388 5020 3896 S 0.0 0.0 0:00.58 ntpd 4331 sw-cp-se 15 0 61336 4572 1480 S 0.0 0.0 5:53.22 sw-cp-serverd 4213 haldaemo 15 0 31252 4460 1684 S 0.0 0.0 0:01.52 hald 4778 postgres 18 0 117m 4164 3484 S 0.0 0.0 0:00.11 postmaster 18555 root 16 0 98.3m 3716 2852 S 0.0 0.0 0:00.01 sshd 4488 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4489 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4492 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4493 sso 18 0 119m 3044 224 S 0.0 0.0 0:00.00 sw-engine-cgi 4490 sso 18 0 119m 3040 220 S 0.0 0.0 0:00.00 sw-engine-cgi

  Read the article

• Performance Tuning a High-Load Apache Server

  - by futureal

  I am looking to understand some server performance problems I am seeing with a (for us) heavily loaded web server. The environment is as follows: Debian Lenny (all stable packages + patched to security updates) Apache 2.2.9 PHP 5.2.6 Amazon EC2 large instance The behavior we're seeing is that the web typically feels responsive, but with a slight delay to begin handling a request -- sometimes a fraction of a second, sometimes 2-3 seconds in our peak usage times. The actual load on the server is being reported as very high -- often 10.xx or 20.xx as reported by top. Further, running other things on the server during these times (even vi) is very slow, so the load is definitely up there. Oddly enough Apache remains very responsive, other than that initial delay. We have Apache configured as follows, using prefork: StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 And KeepAlive as: KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 Looking at the server-status page, even at these times of heavy load we are rarely hitting the client cap, usually serving between 80-100 requests and many of those in the keepalive state. That tells me to rule out the initial request slowness as "waiting for a handler" but I may be wrong. Amazon's CloudWatch monitoring tells me that even when our OS is reporting a load of 15, our instance CPU utilization is between 75-80%. Example output from top: top - 15:47:06 up 31 days, 1:38, 8 users, load average: 11.46, 7.10, 6.56 Tasks: 221 total, 28 running, 193 sleeping, 0 stopped, 0 zombie Cpu(s): 66.9%us, 22.1%sy, 0.0%ni, 2.6%id, 3.1%wa, 0.0%hi, 0.7%si, 4.5%st Mem: 7871900k total, 7850624k used, 21276k free, 68728k buffers Swap: 0k total, 0k used, 0k free, 3750664k cached The majority of the processes look like: 24720 www-data 15 0 202m 26m 4412 S 9 0.3 0:02.97 apache2 24530 www-data 15 0 212m 35m 4544 S 7 0.5 0:03.05 apache2 24846 www-data 15 0 209m 33m 4420 S 7 0.4 0:01.03 apache2 24083 www-data 15 0 211m 35m 4484 S 7 0.5 0:07.14 apache2 24615 www-data 15 0 212m 35m 4404 S 7 0.5 0:02.89 apache2 Example output from vmstat at the same time as the above: procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 8 0 0 215084 68908 3774864 0 0 154 228 5 7 32 12 42 9 6 21 0 198948 68936 3775740 0 0 676 2363 4022 1047 56 16 9 15 23 0 0 169460 68936 3776356 0 0 432 1372 3762 835 76 21 0 0 23 1 0 140412 68936 3776648 0 0 280 0 3157 827 70 25 0 0 20 1 0 115892 68936 3776792 0 0 188 8 2802 532 68 24 0 0 6 1 0 133368 68936 3777780 0 0 752 71 3501 878 67 29 0 1 0 1 0 146656 68944 3778064 0 0 308 2052 3312 850 38 17 19 24 2 0 0 202104 68952 3778140 0 0 28 90 2617 700 44 13 33 5 9 0 0 188960 68956 3778200 0 0 8 0 2226 475 59 17 6 2 3 0 0 166364 68956 3778252 0 0 0 21 2288 386 65 19 1 0 And finally, output from Apache's server-status: Server uptime: 31 days 2 hours 18 minutes 31 seconds Total accesses: 60102946 - Total Traffic: 974.5 GB CPU Usage: u209.62 s75.19 cu0 cs0 - .0106% CPU load 22.4 requests/sec - 380.3 kB/second - 17.0 kB/request 107 requests currently being processed, 6 idle workers C.KKKW..KWWKKWKW.KKKCKK..KKK.KKKK.KK._WK.K.K.KKKKK.K.R.KK..C.C.K K.C.K..WK_K..KKW_CK.WK..W.KKKWKCKCKW.W_KKKKK.KKWKKKW._KKK.CKK... KK_KWKKKWKCKCWKK.KKKCK.......................................... ................................................................ From my limited experience I draw the following conclusions/questions: We may be allowing far too many KeepAlive requests I do see some time spent waiting for IO in the vmstat although not consistently and not a lot (I think?) so I am not sure this is a big concern or not, I am less experienced with vmstat Also in vmstat, I see in some iterations a number of processes waiting to be served, which is what I am attributing the initial page load delay on our web server to, possibly erroneously We serve a mixture of static content (75% or higher) and script content, and the script content is often fairly processor intensive, so finding the right balance between the two is important; long term we want to move statics elsewhere to optimize both servers but our software is not ready for that today I am happy to provide additional information if anybody has any ideas, the other note is that this is a high-availability production installation so I am wary of making tweak after tweak, and is why I haven't played with things like the KeepAlive value myself yet.

  Read the article

• Configuring CESoPSN using Cisco MWR 2941

  - by Rayne

  I'm trying to configure CESoPSN on two Cisco MWR 2941 routers, but the alarm LED lights are always lit. My configuration is modeled after this sample configuration. My setup is as follows: On the Cisco MWRs, E1 0/5 is configured to be CESoPSN, E1 0/9 is configured to be CESoPSN (CAS mode), and E1 0/7 is configured to be SAToP. The two MWRs are connected to each other via the GigabitEthernet port 0/2. The GigE ports are configured as a vlan because the ports are L2 ports and cannot be assigned an IP address directly. The two Cisco MWRs are connected to a traffic simulator, i.e. the traffic simulator will play out E1 traffic to MWR 1 and record the output traffic from MWR 2. On my traffic simulator, when it's connected to the E1 ports 0/5 and 0/9 (both CESoPSN configurations), the "Remote" alarm is on. However, when connected to the E1 ports 0/7 (SAToP configuration), no alarms were on. The GigE connection seems to be working fine (both LED lights on the 2 ports are green). The SAToP configuration seems to be fine too (Left LED is green, right LED is off on both E1 0/7 ports). However, both CESoPSN configurations seem to be not working (Left LED is green, right LED is yellow on both E1 0/5 and 0/9 ports). I don't know if there's anything wrong with my configuration for the CESoPSN, as I'm very new to this. The relevant portions of the configuration are as follows: MWR 1: controller E1 0/5 clock source internal cem-group 5 timeslots 1-31 description E1 CESoPSN example ! controller E1 0/7 clock source internal cem-group 7 unframed description E1 SATOP example ! controller E1 0/9 mode cas clock source internal cem-group 9 timeslots 1-24 description E1 CESoPSN CAS example ! interface Loopback0 ip address 30.30.30.1 255.255.255.255 ! interface GigabitEthernet0/2 switchport access vlan 100 mpls ip ! interface CEM0/5 no ip address cem 5 xconnect 30.30.30.2 305 encapsulation mpls ! ! interface CEM0/7 no ip address cem 7 xconnect 30.30.30.2 307 encapsulation mpls ! ! interface CEM0/9 no ip address cem 9 signaling inband-cas xconnect 30.30.30.2 309 encapsulation mpls ! ! interface Vlan100 ip address 50.50.50.1 255.255.255.0 no ptp enable mpls ip ! no ip classless ip forward-protocol nd ip route 30.30.30.2 255.255.255.255 50.50.50.2 ! MWR 2: controller E1 0/5 clock source internal cem-group 5 timeslots 1-31 description E1 CESoPSN example ! controller E1 0/7 clock source internal cem-group 7 unframed ! controller E1 0/9 mode cas clock source internal cem-group 9 timeslots 1-24 description E1 CESoPSN CAS example ! interface Loopback0 ip address 30.30.30.2 255.255.255.255 ! interface GigabitEthernet0/2 switchport access vlan 100 mpls ip ! interface CEM0/5 no ip address cem 5 xconnect 30.30.30.1 305 encapsulation mpls ! ! interface CEM0/7 no ip address cem 7 xconnect 30.30.30.1 307 encapsulation mpls ! ! interface CEM0/9 no ip address cem 9 signaling inband-cas xconnect 30.30.30.1 309 encapsulation mpls ! ! interface Vlan100 ip address 50.50.50.2 255.255.255.0 no ptp enable mpls ip ! no ip classless ip forward-protocol nd ip route 30.30.30.1 255.255.255.255 50.50.50.1 ! If anyone is familiar with CESoPSN configurations, please advise.

  Read the article

• Trouble with site-to-site OpenVPN & pfSense not passing traffic

  - by JohnCC

  I'm trying to get an OpenVPN tunnel going on pfSense 1.2.3-RELEASE running on embedded routers. I have a local LAN 10.34.43.0/254. The remote LAN is 10.200.1.0/24. The local pfSense is configured as the client, and the remote is configured as the server. My OpenVPN tunnel is using the IP range 10.99.89.0/24 internally. There are also some additional LANs on the remote side routed through the tunnel, but the issue is not with those since my connectivity fails before that point in the chain. The tunnel comes up fine and the logs look healthy. What I find is this:- I can ping and telnet to the remote LAN and the additional remote LANs from the local pfSense box's shell. I cannot ping or telnet to any remote LANs from the local network. I cannot ping or telnet to the local network from the remote LAN or the remote pfSense box's shell. If I tcpdump the tun interfaces on both sides and ping from the local LAN, I see the packets hit the tunnel locally, but they do not appear on the remote side (nor do they appear on the remote LAN interface if I tcpdump that). If I tcpdump the tun interfaces on both sides and ping from the local pfSense shell, I see the packets hit the tunnel locally, and exit the remote side. I can also tcpdump the remote LAN interface and see them pass there too. If I tcpdump the tun interfaces on both sides and ping from the remote pfSense shell, I see the packets hit the remote tun but they do not emerge from the local one. Here is the config file the remote side is using:- #user nobody #group nobody daemon keepalive 10 60 ping-timer-rem persist-tun persist-key dev tun proto udp cipher BF-CBC up /etc/rc.filter_configure down /etc/rc.filter_configure server 10.99.89.0 255.255.255.0 client-config-dir /var/etc/openvpn_csc push "route 10.200.1.0 255.255.255.0" lport <port> route 10.34.43.0 255.255.255.0 ca /var/etc/openvpn_server0.ca cert /var/etc/openvpn_server0.cert key /var/etc/openvpn_server0.key dh /var/etc/openvpn_server0.dh comp-lzo push "route 205.217.5.128 255.255.255.224" push "route 205.217.5.64 255.255.255.224" push "route 165.193.147.128 255.255.255.224" push "route 165.193.147.32 255.255.255.240" push "route 192.168.1.16 255.255.255.240" push "route 192.168.2.16 255.255.255.240" Here is the local config:- writepid /var/run/openvpn_client0.pid #user nobody #group nobody daemon keepalive 10 60 ping-timer-rem persist-tun persist-key dev tun proto udp cipher BF-CBC up /etc/rc.filter_configure down /etc/rc.filter_configure remote <host> <port> client lport 1194 ifconfig 10.99.89.2 10.99.89.1 ca /var/etc/openvpn_client0.ca cert /var/etc/openvpn_client0.cert key /var/etc/openvpn_client0.key comp-lzo You can see the relevant parts of the routing tables extracted from pfSense here http://pastie.org/5365800 The local firewall permits all ICMP from the LAN, and my PC is allowed everything to anywhere. The remote firewall treats its LAN as trusted and permits all traffic on that interface. Can anyone suggest why this is not working, and what I could try next?

  Read the article

• Ubuntu 12 crashed and took down network

  - by Leopd

  We recently set up a new Ubuntu 12.04LTS server on our network. It's not fully configured so it's not doing much beyond sshd and a default apache2 install. But this evening it appears to have crashed. It wasn't responding to the network or the keyboard. But the worst part is, it took down the entire network. My knowledge of the network stack below OSI layer 3 is very limited, so the rest confuses me. When this machine was physically connected to the network, no other machine could connect to the outside internet. When things were broken, running arp showed that our gateway's IP address (10.0.1.1) was listed as "invalid." Unplugging the server from the network fixed the problem, and plugging it back in broke it again. So the crashed server was advertising itself as owning the gateway's IP address? There's nothing at all in syslog during the time when it was causing problems. Any ideas about how to figure out what went wrong or what we can do to prevent it from happening again? I'm hesitant to even put the machine back on the network right now. Update ** It crashed again, and I ran tcpdump -penn arp (thanks bahamat!) for several minutes and got this... (timestamps and duplicate lines removed) 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.191, length 46 00:1e:65:f8:dc:24 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.44 tell 10.0.2.191, length 46 60:d8:19:d4:71:d6 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 60: Request who-has 10.0.1.1 tell 10.0.2.125, length 46 d4:9a:20:04:e9:78 > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.168.1.1 tell 192.168.1.100, length 28 Update 2 ** When the network is functioning properly, arping -c4 10.0.1.1 returns this: ARPING 10.0.1.1 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=0 time=267.982 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=1 time=422.955 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=2 time=299.215 usec 60 bytes from c0:c1:c0:77:25:8e (10.0.1.1): index=3 time=366.926 usec --- 10.0.1.1 statistics --- 4 packets transmitted, 4 packets received, 0% unanswered (0 extra) When the bad server is plugged in, arping -c4 10.0.1.1 returns: ARPING 10.0.1.1 --- 10.0.1.1 statistics --- 4 packets transmitted, 0 packets received, 100% unanswered (0 extra) Context ** 10.0.x.x is the main subnet. 10.0.1.1 is the main internet gateway 10.0.1.44 is a printer 10.0.2.* devices are all laptops / workstations I have no idea what's using the 192.168.x.x subnet -- your guesses are at least as good as mine. A VM on a workstation? A misconfigured WAP? Somebody re-sharing wifi? A machine that failed to DHCP? The offending ubuntu server's MAC address ends in cd:80 so isn't listed in the dump. It should DHCP to 10.0.3.3 Thanks for any help. This ARP stuff is all voodoo to me. Packets just go to IP addresses, right? ;)

  Read the article

• Facing issues in setting up VPN connection(IKEv1) using iphone (Defult Cisco VPN client) and Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using iPhone (Defult Cisco VPN client) and Strongswan 4.5.0 server. The Strongswan server is running on Ubuntu Linux, which is connected to some wifi hotspot. This is the guide which was used. I generated CA, server and client certificate, with the only difference mentioned below. “While generating server certificate, as per link CN=vpn.strongswan.org instead of this I changed CN name to CN=192.168.43.212.” Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on iphone. After installation I notice that certificates are considered as trusted also. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212 Iphone eth0 interface ip address: 192.168.43.72. iphone is also attached with the same wifi hotspot. Below is the snapshot of client configurations. Description Strong swan Server 192.168.43.212 Account ipsecvpn Password ***** Use certificate ON Certificate client The above username and password are in sync with the ipsec.secrets file. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.72 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add With the above configurations when I enable VPN on iphone, it says Could not able to verify server certificate. I ran Wireshark on a Linux server and observe that initially some ISAKMP message exchanges happens between client and server, which are successful but before authorization, client is sending some informational message and soon after this client is showing error as popup Could not able to verify server certificate. Capture logs on Strongswan server and in server logs below errors are observed: From auth.log Apr 25 20:16:08 Linux pluto[4025]: | ISAKMP version: ISAKMP Version 1.0 Apr 25 20:16:08 Linux pluto[4025]: | exchange type: ISAKMP_XCHG_INFO Apr 25 20:16:08 Linux pluto[4025]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 25 20:16:08 Linux pluto[4025]: | message ID: 9d 1a ea 4d Apr 25 20:16:08 Linux pluto[4025]: | length: 76 Apr 25 20:16:08 Linux pluto[4025]: | ICOOKIE: f6 b7 06 b2 b1 84 5b 93 Apr 25 20:16:08 Linux pluto[4025]: | RCOOKIE: 86 92 a0 c2 a6 2f ac be Apr 25 20:16:08 Linux pluto[4025]: | peer: c0 a8 2b 48 Apr 25 20:16:08 Linux pluto[4025]: | state hash entry 8 Apr 25 20:16:08 Linux pluto[4025]: | state object not found Apr 25 20:16:08 Linux pluto[4025]: **packet from 192.168.43.72:500: Informational Exchange is for an unknown (expired?) SA** Apr 25 20:16:08 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 8 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | *time to handle event Apr 25 20:16:16 Linux pluto[4025]: | event after this is EVENT_RETRANSMIT in 2 seconds Apr 25 20:16:16 Linux pluto[4025]: | handling event EVENT_RETRANSMIT for 192.168.43.72 "ios1" #8 Apr 25 20:16:16 Linux pluto[4025]: | sending 76 bytes for EVENT_RETRANSMIT through wlan0 to 192.168.43.72:500: Apr 25 20:16:16 Linux pluto[4025]: | a6 a5 86 41 4b fb ff 99 c9 18 34 61 01 7b f1 d9 Apr 25 20:16:16 Linux pluto[4025]: | 08 10 06 01 e9 1c ea 60 00 00 00 4c ba 7d c8 08 Apr 25 20:16:16 Linux pluto[4025]: | 13 47 95 18 19 31 45 30 2e 22 f9 4d 85 2c 27 bc Apr 25 20:16:16 Linux pluto[4025]: | 9e 9b e1 ae 1e 35 51 6f ab 80 f5 73 3c 15 8d 20 Apr 25 20:16:16 Linux pluto[4025]: | 4b 46 47 86 50 24 3f 13 15 7d d5 17 Apr 25 20:16:16 Linux pluto[4025]: | inserting event EVENT_RETRANSMIT, timeout in 40 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 2 seconds for #10 Apr 25 20:16:16 Linux pluto[4025]: | rejected packet: Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | control: Apr 25 20:16:16 Linux pluto[4025]: | 30 00 00 00 00 00 00 00 00 00 00 00 0b 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 6f 00 00 00 02 03 03 00 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 02 00 00 00 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | name: Apr 25 20:16:16 Linux pluto[4025]: | 02 00 01 f4 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: **ERROR: asynchronous network error report on wlan0 for message to 192.168.43.72 port 500, complainant 192.168.43.72: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)]** Anybody please provide some update about this error and how to solve this issue.

  Read the article

• DNS Server Behind NAT

  - by Bryan

  I've got a Bind 9 DNS server sitting behind a NAT firewall, assume the Internet facing IP is 1.2.3.4 There are no restrictions on outgoing traffic, and port 53 (TCP/UDP) is forwarded from 1.2.3.4 to the internal DNS server (10.0.0.1). There are no IP Tables rules on either the VPS or the internal Bind 9 server. From a remote Linux VPS located elsewhere on the internet, nslookup works fine # nslookup foo.example.com 1.2.3.4 Server: 1.2.3.4 Address: 1.2.3.4#53 Name: foo.example.com Addresss: 9.9.9.9 However, when using the host command on the remote VPS, I receive the following output: # host foo.example.com 1.2.3.4 ;; reply from unexpected source: 1.2.3.4#13731, expected 1.2.3.4#53 ;; reply from unexpected source: 1.2.3.4#13731, expected 1.2.3.4#53 ;; connection timed out; no servers could be reached. From the VPS, I can establish a connection (using telnet) to 1.2.3.4:53 From the internal DNS server (10.0.0.1), the host command appears to be fine: # host foo.example.com 127.0.0.1 Using domain server: Name: 127.0.0.1 Address: 127.0.0.1#53 Aliases: foo.example.com has address 9.9.9.9 Any suggestions as to why the host command on my VPS is complaining about the reply coming back from another port, and what can I do to fix this? Further info: From a windows host external to the network >nslookup foo.example.com 1.2.3.4 DNS request timeout timeout was 2 seconds Server: UnKnown Address: 1.2.3.4 DNS request timed out. timeout was 2 seconds DNS request timed out. timeout was 2 seconds DNS request timed out. timeout was 2 seconds DNS request timed out. timeout was 2 seconds *** Request to UnKnown timed-out This is a default install of bind from Ubuntu 12.04 LTS, with around 11 zones configured. $ named -v BIND 9.8.1-P1 TCP Dump (filtered) from internal DNS server 20:36:29.175701 IP pc.external.com.57226 > dns.example.com.domain: 1+ PTR? 4.3.2.1.in-addr.arpa. (45) 20:36:29.175948 IP dns.example.com.domain > pc.external.com.57226: 1 Refused- 0/0/0 (45) 20:36:31.179786 IP pc.external.com.57227 > dns.example.com.domain: 2+[|domain] 20:36:31.179960 IP dns.example.com.domain > pc.external.com.57227: 2 Refused-[|domain] 20:36:33.180653 IP pc.external.com.57228 > dns.example.com.domain: 3+[|domain] 20:36:33.180906 IP dns.example.com.domain > pc.external.com.57228: 3 Refused-[|domain] 20:36:35.185182 IP pc.external.com.57229 > dns.example.com.domain: 4+ A? foo.example.com. (45) 20:36:35.185362 IP dns.example.com.domain > pc.external.com.57229: 4*- 1/1/1 (95) 20:36:37.182844 IP pc.external.com.57230 > dns.example.com.domain: 5+ AAAA? foo.example.com. (45) 20:36:37.182991 IP dns.example.com.domain > pc.external.com.57230: 5*- 0/1/0 (119) TCP Dump from client during query 21:24:52.054374 IP pc.external.com.43845 > dns.example.com.53: 6142+ A? foo.example.com. (45) 21:24:52.104694 IP dns.example.com.29242 > pc.external.com.43845: UDP, length 95

  Read the article

• Samba with remote LDAP authentication doesn`t see users properly

  - by LucasBr

  I'm trying to setup a samba server authenticated by a remote LDAP server, and I'm having some problems that I can't figure how to solve. I was able to make an getent passwd at samba server and I could see all users at ldapserver, but when I tried to access \\SAMBASERVER at my windows box I had this at the /var/log/samba/log.mywindowsbox: <...snip...> [2012/10/19 13:05:22.449684, 2] smbd/sesssetup.c:1413(setup_new_vc_session) setup_new_vc_session: New VC == 0, if NT4.x compatible we would close all old resources. [2012/10/19 13:05:22.449692, 3] smbd/sesssetup.c:1212(reply_sesssetup_and_X_spnego) Doing spnego session setup [2012/10/19 13:05:22.449701, 3] smbd/sesssetup.c:1254(reply_sesssetup_and_X_spnego) NativeOS=[] NativeLanMan=[] PrimaryDomain=[] [2012/10/19 13:05:22.449717, 3] libsmb/ntlmssp.c:747(ntlmssp_server_auth) Got user=[lucas] domain=[BUSINESS] workstation=[MYWINDOWSBOX] len1=24 len2=24 [2012/10/19 13:05:22.449747, 3] auth/auth.c:216(check_ntlm_password) check_ntlm_password: Checking password for unmapped user [BUSINESS]\[lucas]@[MYWINDOWSBOX] with the new password interface [2012/10/19 13:05:22.449759, 3] auth/auth.c:219(check_ntlm_password) check_ntlm_password: mapped user is: [SAMBASERVER]\[lucas]@[MYWINDOWSBOX] [2012/10/19 13:05:22.449773, 3] smbd/sec_ctx.c:210(push_sec_ctx) push_sec_ctx(0, 0) : sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449783, 3] smbd/uid.c:429(push_conn_ctx) push_conn_ctx(0) : conn_ctx_stack_ndx = 0 [2012/10/19 13:05:22.449791, 3] smbd/sec_ctx.c:310(set_sec_ctx) setting sec ctx (0, 0) - sec_ctx_stack_ndx = 1 [2012/10/19 13:05:22.449922, 2] lib/smbldap.c:950(smbldap_open_connection) smbldap_open_connection: connection opened [2012/10/19 13:05:23.001517, 3] lib/smbldap.c:1166(smbldap_connect_system) ldap_connect_system: successful connection to the LDAP server [2012/10/19 13:05:23.007713, 3] smbd/sec_ctx.c:418(pop_sec_ctx) pop_sec_ctx (0, 0) - sec_ctx_stack_ndx = 0 [2012/10/19 13:05:23.007733, 3] auth/auth_sam.c:399(check_sam_security) check_sam_security: Couldn't find user 'lucas' in passdb. [2012/10/19 13:05:23.007743, 2] auth/auth.c:314(check_ntlm_password) check_ntlm_password: Authentication for user [lucas] -> [lucas] FAILED with error NT_STATUS_NO_SUCH_USER [2012/10/19 13:05:23.007760, 3] smbd/error.c:80(error_packet_set) error packet at smbd/sesssetup.c(111) cmd=115 (SMBsesssetupX) NT_STATUS_LOGON_FAILURE [2012/10/19 13:05:23.010469, 3] smbd/process.c:1489(process_smb) Transaction 3 of length 142 (0 toread) <...snip...> /etc/samba/smb.conf file follows: [global] dos charset = 850 unix charset = LOCALE workgroup = BUSINESS netbios name = SAMBASERVER bind interfaces only = true interfaces = lo eth0 eth1 smb ports = 139 hosts deny = All hosts allow = 192.168.78. 192.168.255. 127.0.0.1 10.149.122. 192.168.0. name resolve order = wins bcast hosts log level = 3 syslog = 0 log file = /var/log/samba/log.%m max log size = 100000 domain logons = No wins support = Yes wins proxy = No client ntlmv2 auth = Yes lanman auth = Yes ntlm auth = Yes dns proxy = Yes time server = Yes security = user encrypt passwords = Yes obey pam restrictions = Yes ldap password sync = Yes unix password sync = Yes passdb backend = ldapsam:"ldap://192.168.78.206" ldap ssl = off ldap admin dn = uid=root,ou=Users,dc=business,dc=intranet ldap suffix = ldap group suffix = ou=Groups ldap user suffix = ou=Users ldap machine suffix = ou=Computers ldap idmap suffix = ou=Idmap ldap delete dn = Yes add user script = /usr/sbin/smbldap-useradd -m "%u" delete user script = /usr/sbin/smbldap-userdel "%u" add group script = /usr/sbin/smbldap-groupadd -p "%g" delete group script = /usr/sbin/smbldap-groupdel "%g" add user to group script = /usr/sbin/smbldap-groupmod -m "%u" "%g" delete user from group script = /usr/sbin/smbldap-groupmod -x "%u" "%g" set primary group script = /usr/sbin/smbldap-usermod -g "%g" "%u" add machine script = /usr/sbin/smbldap-useradd -W -t5 "%u" idmap backend = ldap:"ldap://192.168.78.206" idmap uid = 16777216-33554431 idmap gid = 16777216-33554431 load printers = No printcap name = /dev/null map acl inherit = Yes map untrusted to domain = Yes enable privileges = Yes veto files = /lost+found/ /publicftp/ So, \\SAMBASERVER says he couldn't find my user, but I can see it by getent passwd . What I can do in order to SAMBASERVER see and authenticate my user? Thanks in advance!

  Read the article

• Site-to-site VPN using MD5 instead of SHA and getting regular disconnection

  - by Steven

  We are experiencing some strange behavior with a site-to-site IPsec VPN that goes down about every week for 30 minutes (Iam told 30 minutes exactly). I don't have access to the logs, so it's difficult to troubleshoot. What is also strange is that the two VPN devices are set to use SHA hash algorithm but apparently end up agreeing to use MD5. Does anybody have a clue? or is this just insufficient information? Edit: Here is an extract of the log of one of the two VPN devices, which is a Cisco 3000 series VPN concentrator. 27981 03/08/2010 10:02:16.290 SEV=4 IKE/41 RPT=16120 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27983 03/08/2010 10:02:56.930 SEV=4 IKE/41 RPT=16121 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 27986 03/08/2010 10:03:35.370 SEV=4 IKE/41 RPT=16122 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) [… same continues for another 15 minutes …] 28093 03/08/2010 10:19:46.710 SEV=4 IKE/41 RPT=16140 xxxxxxxx IKE Initiator: New Phase 1, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28096 03/08/2010 10:20:17.720 SEV=5 IKE/172 RPT=1291 xxxxxxxx Group [xxxxxxxx] Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end IS behind a NAT device 28100 03/08/2010 10:20:17.820 SEV=3 IKE/134 RPT=79 xxxxxxxx Group [xxxxxxxx] Mismatch: Configured LAN-to-LAN proposal differs from negotiated proposal. Verify local and remote LAN-to-LAN connection lists. 28103 03/08/2010 10:20:17.820 SEV=4 IKE/119 RPT=1197 xxxxxxxx Group [xxxxxxxx] PHASE 1 COMPLETED 28104 03/08/2010 10:20:17.820 SEV=4 AUTH/22 RPT=1031 xxxxxxxx User [xxxxxxxx] Group [xxxxxxxx] connected, Session Type: IPSec/LAN- to-LAN 28106 03/08/2010 10:20:17.820 SEV=4 AUTH/84 RPT=39 LAN-to-LAN tunnel to headend device xxxxxxxx connected 28110 03/08/2010 10:20:17.920 SEV=5 IKE/25 RPT=1291 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28113 03/08/2010 10:20:17.920 SEV=5 IKE/24 RPT=88 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28116 03/08/2010 10:20:17.920 SEV=5 IKE/66 RPT=1290 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28117 03/08/2010 10:20:17.930 SEV=5 IKE/25 RPT=1292 xxxxxxxx Group [xxxxxxxx] Received remote Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28120 03/08/2010 10:20:17.930 SEV=5 IKE/24 RPT=89 xxxxxxxx Group [xxxxxxxx] Received local Proxy Host data in ID Payload: Address xxxxxxxx, Protocol 0, Port 0 28123 03/08/2010 10:20:17.930 SEV=5 IKE/66 RPT=1291 xxxxxxxx Group [xxxxxxxx] IKE Remote Peer configured for SA: L2L: 1A 28124 03/08/2010 10:20:18.070 SEV=4 IKE/173 RPT=17330 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices. 28127 03/08/2010 10:20:18.070 SEV=4 IKE/49 RPT=17332 xxxxxxxx Group [xxxxxxxx] Security negotiation complete for LAN-to-LAN Group (xxxxxxxx) Responder, Inbound SPI = 0x56a4fe5c, Outbound SPI = 0xcdfc3892 28130 03/08/2010 10:20:18.070 SEV=4 IKE/120 RPT=17332 xxxxxxxx Group [xxxxxxxx] PHASE 2 COMPLETED (msgid=37b3b298) 28131 03/08/2010 10:20:18.750 SEV=4 IKE/41 RPT=16141 xxxxxxxx Group [xxxxxxxx] IKE Initiator: New Phase 2, Intf 2, IKE Peer xxxxxxxx local Proxy Address xxxxxxxx, remote Proxy Address xxxxxxxx, SA (L2L: 1A) 28135 03/08/2010 10:20:18.870 SEV=4 IKE/173 RPT=17331 xxxxxxxx Group [xxxxxxxx] NAT-Traversal successfully negotiated! IPSec traffic will be encapsulated to pass through NAT devices.

  Read the article

• iPhone doesn't save password for Cisco IPsec VPN using racoon daemon

  - by dsx

  On my Debian server I had set up racoon daemon (1:0.8.0-14) for Cisco IPSec VPN using certificates for authentication. My racoon.conf is like following: log info; path certificate "/etc/racoon/certs"; listen { isakmp $SERVER_IP_HERE [500]; isakmp_natt $SERVER_IP_HERE [4500]; } timer { natt_keepalive 10 sec; } remote anonymous { lifetime time 24 hours; proposal_check obey; passive on; exchange_mode aggressive,main; my_identifier asn1dn; peers_identifier asn1dn; verify_identifier on; certificate_type x509 "cert_name.crt" "key_name.key"; ca_type x509 "ca.crt"; mode_cfg on; verify_cert on; ike_frag on; generate_policy on; nat_traversal on; dpd_delay 20; proposal { encryption_algorithm aes; hash_algorithm sha1; authentication_method xauth_rsa_server; dh_group modp1024; } } mode_cfg { conf_source local; auth_source system; auth_throttle 3; save_passwd on; dns4 8.8.8.8; network4 $SOME_LAN_SUBNET; netmask4 255.255.255.0; pool_size 128; } sainfo anonymous { pfs_group 2; lifetime time 24 hour; encryption_algorithm aes; authentication_algorithm hmac_sha1; compression_algorithm deflate; } I'm not using PSK authentication here. Using iPhone configuration utility I had uploaded all required certificates to iPhone and set up VPN on demand. Everything works just fine except one thing: iPhone refuses to save VPN password regardless of save_passwd on; in racoon configuration file. As opposed to iPhone behaviour, Mac OS X 10.8.2 have no problems saving password. I had examined iPhone log file and found following: racoon[151] <Notice>: >>>>> phase change status = phase 1 established configd[50] <Notice>: IPSec Network Configuration started. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-ADDRESS = $SUBNET_IP_HERE. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-MASK = 255.255.255.0. configd[50] <Notice>: IPSec Network Configuration: SAVE-PASSWORD = 0. configd[50] <Notice>: IPSec Network Configuration: INTERNAL-IP4-DNS = 8.8.8.8. configd[50] <Notice>: IPSec Network Configuration: BANNER = . configd[50] <Notice>: IPSec Network Configuration: DEF-DOMAIN = . configd[50] <Notice>: IPSec Network Configuration: DEFAULT-ROUTE = local-address $SUBNET_IP_HERE/32. configd[50] <Notice>: IPSec Phase2 starting. configd[50] <Notice>: IPSec Network Configuration established. configd[50] <Notice>: IPSec Phase1 established. Please note IPSec Network Configuration message containing SAVE-PASSWORD = 0.. Is it a bug in racoon daemon on server, or iPhone (iOS version is 6.0.1 (10A523)) or it is me missing something? How to make iPhone remember IPSec VPN password?

  Read the article

• Cannot log into Oracle Enterprise Manager 11g: ORA-28001

  - by Álvaro G. Vicario

  I can no longer log into Oracle Enterprise Manager 11g. I get this error message: ORA-28001: the password has expired (DBD ERROR: OCISessionBegin) I could log into the server using SQL*Plus. I warned me that the password was going to expire in 7 days (which is not the same as being already expired). Following advice from several documents, I ran these commands from SQL*Plus: ALTER USER sys IDENTIFIED BY new_password; ALTER USER system IDENTIFIED BY new_password; SQL*Plus no longer warns about passwords, but I still cannot use the Enterprise Manager. Then I followed this to remove password expiration: ALTER PROFILE default LIMIT password_life_time UNLIMITED And I've also restarted the Oracle services. In case it was using cached credentials, I've tried to connect from several browsers in several computers. No way: I still get ORA-28001 in Enterprise Manager. What am I missing? Update: Some more info SQL> select username,ACCOUNT_STATUS,EXPIRY_DATE from dba_users; USERNAME ACCOUNT_STATUS EXPIRY_D ------------------------------ -------------------------------- -------- MGMT_VIEW OPEN SYS OPEN SYSTEM OPEN [...] DBSNMP EXPIRED 24/05/10 SYSMAN EXPIRED 24/05/10 OUTLN EXPIRED & LOCKED 16/11/09 FLOWS_FILES EXPIRED & LOCKED 16/11/09 USERNAME ACCOUNT_STATUS EXPIRY_D ------------------------------ -------------------------------- -------- MDSYS EXPIRED & LOCKED 16/11/09 ORDSYS EXPIRED & LOCKED 16/11/09 EXFSYS EXPIRED & LOCKED 16/11/09 WMSYS EXPIRED & LOCKED 16/11/09 WKSYS EXPIRED & LOCKED 16/11/09 WK_TEST EXPIRED & LOCKED 16/11/09 CTXSYS EXPIRED & LOCKED 16/11/09 ANONYMOUS EXPIRED & LOCKED 16/11/09 XDB EXPIRED & LOCKED 16/11/09 WKPROXY EXPIRED & LOCKED 16/11/09 ORDPLUGINS EXPIRED & LOCKED 16/11/09 USERNAME ACCOUNT_STATUS EXPIRY_D ------------------------------ -------------------------------- -------- FLOWS_030000 EXPIRED & LOCKED 16/11/09 OWBSYS EXPIRED & LOCKED 16/11/09 SI_INFORMTN_SCHEMA EXPIRED & LOCKED 16/11/09 OLAPSYS EXPIRED & LOCKED 16/11/09 SCOTT EXPIRED & LOCKED 16/11/09 ORACLE_OCM EXPIRED & LOCKED 16/11/09 TSMSYS EXPIRED & LOCKED 16/11/09 XS$NULL EXPIRED & LOCKED 16/11/09 BI EXPIRED & LOCKED 16/11/09 PM EXPIRED & LOCKED 16/11/09 MDDATA EXPIRED & LOCKED 16/11/09 USERNAME ACCOUNT_STATUS EXPIRY_D ------------------------------ -------------------------------- -------- IX EXPIRED & LOCKED 16/11/09 SH EXPIRED & LOCKED 16/11/09 DIP EXPIRED & LOCKED OE EXPIRED & LOCKED 16/11/09 APEX_PUBLIC_USER EXPIRED & LOCKED 16/11/09 HR EXPIRED & LOCKED 16/11/09 SPATIAL_CSW_ADMIN_USR EXPIRED & LOCKED 16/11/09 SPATIAL_WFS_ADMIN_USR EXPIRED & LOCKED 16/11/09

  Read the article

• vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

  - by kce

  I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

  Read the article

• "Can't create table" when having to many partitions

  - by Chris

  I am currently having a problem I dont understand. Wherever I look it says mySQL (5.5) / InnoDB doesnt have a table limit. I wanted to test the InnoDB compression and was about to create an empty copy of an existing table and ran into the following problem. this one works: CREATE TABLE `hsc` ( LOTS OF STUFF ) ENGINE=InnoDB CHARSET=utf8 PARTITION BY RANGE (pid) SUBPARTITION BY HASH (cons) SUBPARTITIONS 2 (PARTITION hsc_p0 VALUES LESS THAN (10000) , PARTITION hsc_p1 VALUES LESS THAN (20000) , PARTITION hsc_p2 VALUES LESS THAN (30000) , PARTITION hsc_p3 VALUES LESS THAN (40000) , PARTITION hsc_p4 VALUES LESS THAN (50000) , PARTITION hsc_p40 VALUES LESS THAN (4000000) ); this one doesn't: CREATE TABLE `hsc` ( LOTS OF STUFF ) ENGINE=InnoDB CHARSET=utf8 PARTITION BY RANGE (pid) SUBPARTITION BY HASH (cons) SUBPARTITIONS 2 (PARTITION hsc_p0 VALUES LESS THAN (10000) , PARTITION hsc_p1 VALUES LESS THAN (20000) , PARTITION hsc_p2 VALUES LESS THAN (30000) , PARTITION hsc_p3 VALUES LESS THAN (40000) , PARTITION hsc_p4 VALUES LESS THAN (50000) , PARTITION hsc_p5 VALUES LESS THAN (75000) , PARTITION hsc_p6 VALUES LESS THAN (100000) , PARTITION hsc_p7 VALUES LESS THAN (125000) , PARTITION hsc_p8 VALUES LESS THAN (150000) , PARTITION hsc_p9 VALUES LESS THAN (175000) , PARTITION hsc_p40 VALUES LESS THAN (4000000) ); ERROR 1005 (HY000): Can't create table 'hsc' (errno: 1) Its reproducable by removing the number of partitions and adding them again. it does not have to do anything with the name of the table as i tried various names. there is also enough empty space on the HDD. /dev/simfs 230G 26G 192G 12% /var/lib/mysql.mnt There should be no limit on the partitions http://dev.mysql.com/doc/refman/5.5/en/partitioning-limitations.html Maximum number of partitions. The maximum possible number of partitions for a given table (that does not use the NDB storage engine) is 1024. This number includes subpartitions. i have increased both open_files show variables where variable_name LIKE '%open_files%'; +-------------------+-------+ | Variable_name | Value | +-------------------+-------+ | innodb_open_files | 512 | | open_files_limit | 1536 | +-------------------+-------+ No change. Any clues where should I start looking? UPDATE: the whole thing is running in an openvz environment. i saw in users_beancounters that the numflock was a problem, so i increased it. but the problem still persists. maybe this helps: ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 515011 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 10240 cpu time (seconds, -t) unlimited max user processes (-u) 515011 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt 200: kmemsize 9309653 13357056 14372700 14790164 0 lockedpages 0 1008 2048 2048 0 privvmpages 675424 686528 1048576 1572864 0 shmpages 33 673 21504 21504 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numproc 49 90 240 240 0 physpages 243761 246945 0 9223372036854775807 0 vmguarpages 0 0 1048576 1048576 0 oomguarpages 81672 83305 1048576 1048576 0 numtcpsock 6 8 360 360 0 numflock 175 188 512 512 8 numpty 1 9 16 16 0 numsiginfo 0 48 256 256 0 tcpsndbuf 104640 263912 1720320 2703360 0 tcprcvbuf 98304 131072 1720320 2703360 0 othersockbuf 32368 89304 1126080 2097152 0 dgramrcvbuf 0 2312 262144 262144 0 numothersock 19 28 360 360 0 dcachesize 2285052 3624426 3409920 3624960 0 numfile 616 870 9312 9312 0 dummy 0 0 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numiptent 24 24 128 128 0

  Read the article

• ASA 5505 stops local internet when connected to VPN

  - by g18c

  Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

  Read the article

• FFMPEG dropping frames while encoding JPEG sequence at color change

  - by Matt

  I'm trying to put together a slide show using imagemagick and FFMPEG. I use imagemagick to expand a single photo into 30fps video (imagemagick also handles things like putting some text captions on the frames along the way). When I go to let ffmpeg digest it into a video it clips along nicely on the color parts of the video, but when it gets to a black and white section it reports "frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703" and drops every frame of video until it hits something with color. As you can imagine this results in entire photos being removed from the slideshow. Here is my latest dump... ffmpeg -y -r 30 -i "teststream/%06d.jpg" -c:v libx264 -r 30 newffmpeg.mp4 ffmpeg version git-2012-12-10-c3bb333 Copyright (c) 2000-2012 the FFmpeg developers built on Dec 10 2012 22:02:04 with gcc 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) configuration: --enable-gpl --enable-libfaac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 12.100 / 52. 12.100 libavcodec 54. 79.101 / 54. 79.101 libavformat 54. 49.100 / 54. 49.100 libavdevice 54. 3.102 / 54. 3.102 libavfilter 3. 26.101 / 3. 26.101 libswscale 2. 1.103 / 2. 1.103 libswresample 0. 17.102 / 0. 17.102 libpostproc 52. 2.100 / 52. 2.100 Input #0, image2, from 'teststream/%06d.jpg': Duration: 00:12:02.80, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj444p, 720x480 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [libx264 @ 0x3450140] using SAR=1/1 [libx264 @ 0x3450140] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 [libx264 @ 0x3450140] profile High, level 3.0 [libx264 @ 0x3450140] 264 - core 129 r2 1cffe9f - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 lookahead_threads=2 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'newffmpeg.mp4': Metadata: encoder : Lavf54.49.100 Stream #0:0: Video: h264 ([33][0][0][0] / 0x0021), yuvj420p, 720x480 [SAR 1:1 DAR 3:2], q=-1--1, 15360 tbn, 30 tbc Stream mapping: Stream #0:0 - #0:0 (mjpeg - libx264) Press [q] to stop, [?] for help Input stream #0:0 frame changed from size:720x480 fmt:yuvj444p to size:720x480 fmt:yuvj422p Input stream #0:0 frame changed from size:720x480 fmt:yuvj422p to size:720x480 fmt:yuvj444pp=584 frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703 video:5179kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.472425% [libx264 @ 0x3450140] frame I:9 Avg QP:20.10 size: 33933 [libx264 @ 0x3450140] frame P:636 Avg QP:24.12 size: 6737 [libx264 @ 0x3450140] frame B:1385 Avg QP:27.04 size: 514 [libx264 @ 0x3450140] consecutive B-frames: 2.5% 15.2% 13.2% 69.2% [libx264 @ 0x3450140] mb I I16..4: 8.3% 80.3% 11.5% [libx264 @ 0x3450140] mb P I16..4: 1.5% 2.5% 0.2% P16..4: 41.7% 18.0% 10.3% 0.0% 0.0% skip:25.9% [libx264 @ 0x3450140] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 26.6% 0.6% 0.1% direct: 0.2% skip:72.3% L0:35.0% L1:60.3% BI: 4.7% [libx264 @ 0x3450140] 8x8 transform intra:64.1% inter:75.1% [libx264 @ 0x3450140] coded y,uvDC,uvAC intra: 51.6% 78.0% 43.7% inter: 10.6% 14.9% 2.1% [libx264 @ 0x3450140] i16 v,h,dc,p: 29% 19% 6% 46% [libx264 @ 0x3450140] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 23% 15% 17% 5% 9% 10% 7% 8% 6% [libx264 @ 0x3450140] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 31% 18% 11% 5% 9% 10% 6% 6% 4% [libx264 @ 0x3450140] i8c dc,h,v,p: 46% 18% 24% 12% [libx264 @ 0x3450140] Weighted P-Frames: Y:20.1% UV:18.7% [libx264 @ 0x3450140] ref P L0: 59.2% 23.2% 13.1% 4.3% 0.2% [libx264 @ 0x3450140] ref B L0: 88.7% 8.3% 3.0% [libx264 @ 0x3450140] ref B L1: 95.0% 5.0% [libx264 @ 0x3450140] kb/s:626.88 Received signal 2: terminating. One last note: If I remove the -r 30 from the input and output it works flawlessly. I have no idea why the -r 30 is causing it to freak out.

  Read the article

< Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >