Search Results

Search found 9649 results on 386 pages for 'usb audio'.

Page 104/386 | < Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >

  • How do I activate the F_LINE input in a transplanted HP chassis?

    - by admin
    I have an HP Pavilion Media Center PC chassis, vintage 2003 or so and I replaced the motherboard in it with a newer (vintage 2009) HP motherboard, M2N68-LA (Narra 5). I have scoured the internet trying to find pinouts for the motherboard to no avail. My question concerns the front panel audio, specifically Line In. The old chassis was built for AC97 but the new mobo is build for the newer HD audio standard. I figured out by comparison & experimentally how to connect the Mic & Headphone jacks to the HD audio header of the mobo by adding a manual switch to set the SENSE lines. Now all works fine for Mic & headphone. The old chassis also has a front panel Line In jack that the newer HP chassis does not have. However, the new mobo has a 4 pin white connector labeled F_LINE that I believe is a line input. Under Windows 7 I see the two Line Inputs in the mixer but I can't get one of them to become active. The 4 pin F_LINE connector uses the two middle pins for ground, and presumably the other two for left and right audio inputs. There are no pins for sensing on that connector. Can anyone tell me how to use that F_LINE input for the front panel, or how to activate it?

    Read the article

  • Sound doesn't work anymore after replacing RAM

    - by thejh
    Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

    Read the article

  • My Hard Drive isn't Working

    - by MeCB
    I never use Safely Remove Hardware with Windows XP. It has been working for me for years with my SD card, mouse, hard drive and memory stick. My hard drive has a USB cable and power cord so I can hook it up to any desktop hard drive. Now my hard drives don't like this and I did not know this till now. I am always careful and to wait till it is all finish accessing the USB before I unplug it. Now three of my hard drives can't be seen by Windows, though the others still work. when I hook it up to another computer it works fine. I use the same USB cable to hook up all of my hard drives one at a time. So my USB cable is good. I think that when I unplugged the hard drive this one time, it had a file it still wanted to see and now only this drive does not work only this computer. Then the same thing happens to my other two hard drive after I used it for a week with the same cables. How can I fix this?

    Read the article

  • How to boost playback volume in real time on media recorded with a very low volume.

    - by L Marksman
    I have never heard a satisfactory answer to this often misunderstood question, let me explain. Lets say I have a sound card and earphones/speakers that can play back audio loud enough in most cases. This is great but the problem is that you always find people who do not know how to record audio, from Youtube video's to music. So now you end up with a audio playback that only uses 10% or less of the capacity of your sound hardware, in vista/win 7 you will see this frequently in the mixer with the volume pushed up to max but the green sound level only goes up a millimeter or two. I am looking for (preferably free) software or a method to boost the sound level of any audio from any source in real time to use more of my hardware capacity similar to what VLC media player can do. Oh and please, do not tell me it is impossible. I am not trying to boost the volume past what my hardware is capable of, I am just trying to use my hardware's full capacity. Also please do not tell met to buy new hardware, I know I can use hardware amplification, I don't want to (like many others) spend money on a simple little problem like this. Thanks!

    Read the article

  • Cannot open /dev/rfcomm1 : Host is down

    - by srj0408
    I am working on raspberry PI and on Bluetooth. I am using old raspberry pi kernel as the new one has got some bugs that were not resolved with respect to the bluez daemon. At present my kernel version is 3.6.11. I am using a USB bluetooth dongle and my sole purpose is to auto connect the bluetooth dongle when ever it is in range. For that i think i have to run a script in the backend on RPI that will keep on checking the existence of usb bluetooth dongle. I started from the very scratch. I installed bluez daemon using apt-get install bluetooth bluez utils blueman and then i used hciconfig which gives me that my bluetooth usb dongle is working fine. But when i did hcitool scan , it give me no device in range even though my Serial bluetooth Device was on. I wasn't able to find any device in vicinity. Also when i unplugged and plug the USB dongle again, i was able to scan the serial device , but when i repeat the process, i find the earlier condition of not finding any deice. I had find another useful link, but that need address of the bluetooth device that need to be connected. I want to automate this using hcitool scan, storing the output to the a file and then comparing it with already paired devices and their name. For that i need to figure out why hcitool scan is sometime working and sometime not. ? Can some one help me in figuring out why this is happening. Is there any problem on hardware side i.e Bluetooth dongle is buggy or i had some problem in bluez utils. Edit 1: While as of now, hcitool scan is giving me my remote device address but still i am getting the same issue of HOUST IS DOWN, '/dev/rfcomm1'. I am really not getting any idea of what to be done.

    Read the article

  • Install usblib package - Ubuntu

    - by Tom celic
    I need the package libusb for another package I am installing. I tried the following which seemed to install the package, sudo apt-get install libusb-dev but when I try to install the other package I get, configure: error: Package requirements (libusb-1.0 >= 0.9.1) were not met: No package 'libusb-1.0' found Consider adjusting the PKG_CONFIG_PATH environment variable if you installed software in a non-standard prefix. Alternatively, you may set the environment variables LIBUSB_CFLAGS and LIBUSB_LIBS to avoid the need to call pkg-config. See the pkg-config man page for more details. When I run the command dpkg -L libusb-dev, I get: /. /usr /usr/bin /usr/bin/libusb-config /usr/include /usr/include/usb.h /usr/lib /usr/lib/libusb.a /usr/lib/libusb.la /usr/lib/pkgconfig /usr/lib/pkgconfig/libusb.pc /usr/share /usr/share/doc /usr/share/doc/libusb-dev /usr/share/doc/libusb-dev/html /usr/share/doc/libusb-dev/html/index.html /usr/share/doc/libusb-dev/html/preface.html /usr/share/doc/libusb-dev/html/intro.html /usr/share/doc/libusb-dev/html/intro-overview.html /usr/share/doc/libusb-dev/html/intro-support.html /usr/share/doc/libusb-dev/html/api.html /usr/share/doc/libusb-dev/html/api-device-interfaces.html /usr/share/doc/libusb-dev/html/api-timeouts.html /usr/share/doc/libusb-dev/html/api-types.html /usr/share/doc/libusb-dev/html/api-synchronous.html /usr/share/doc/libusb-dev/html/api-return-values.html /usr/share/doc/libusb-dev/html/functions.html /usr/share/doc/libusb-dev/html/ref.core.html /usr/share/doc/libusb-dev/html/function.usbinit.html /usr/share/doc/libusb-dev/html/function.usbfindbusses.html /usr/share/doc/libusb-dev/html/function.usbfinddevices.html /usr/share/doc/libusb-dev/html/function.usbgetbusses.html /usr/share/doc/libusb-dev/html/ref.deviceops.html /usr/share/doc/libusb-dev/html/function.usbopen.html /usr/share/doc/libusb-dev/html/function.usbclose.html /usr/share/doc/libusb-dev/html/function.usbsetconfiguration.html /usr/share/doc/libusb-dev/html/function.usbsetaltinterface.html /usr/share/doc/libusb-dev/html/function.usbresetep.html /usr/share/doc/libusb-dev/html/function.usbclearhalt.html /usr/share/doc/libusb-dev/html/function.usbreset.html /usr/share/doc/libusb-dev/html/function.usbclaiminterface.html /usr/share/doc/libusb-dev/html/function.usbreleaseinterface.html /usr/share/doc/libusb-dev/html/ref.control.html /usr/share/doc/libusb-dev/html/function.usbcontrolmsg.html /usr/share/doc/libusb-dev/html/function.usbgetstring.html /usr/share/doc/libusb-dev/html/function.usbgetstringsimple.html /usr/share/doc/libusb-dev/html/function.usbgetdescriptor.html /usr/share/doc/libusb-dev/html/function.usbgetdescriptorbyendpoint.html /usr/share/doc/libusb-dev/html/ref.bulk.html /usr/share/doc/libusb-dev/html/function.usbbulkwrite.html /usr/share/doc/libusb-dev/html/function.usbbulkread.html /usr/share/doc/libusb-dev/html/ref.interrupt.html /usr/share/doc/libusb-dev/html/function.usbinterruptwrite.html /usr/share/doc/libusb-dev/html/function.usbinterruptread.html /usr/share/doc/libusb-dev/html/ref.nonportable.html /usr/share/doc/libusb-dev/html/function.usbgetdrivernp.html /usr/share/doc/libusb-dev/html/function.usbdetachkerneldrivernp.html /usr/share/doc/libusb-dev/html/examples.html /usr/share/doc/libusb-dev/html/examples-code.html /usr/share/doc/libusb-dev/html/examples-tests.html /usr/share/doc/libusb-dev/html/examples-other.html /usr/share/doc/libusb-dev/copyright /usr/share/doc-base /usr/share/doc-base/libusb-dev /usr/share/man /usr/share/man/man1 /usr/share/man/man1/libusb-config.1.gz /usr/lib/libusb.so /usr/share/doc/libusb-dev/changelog.Debian.gz Any ideas??

    Read the article

  • Playing NSF music in FMOD.net

    - by Tesserex
    So, as the title says, I want to be able to play NSF files using FMOD, because my project already uses FMOD and I'd rather not replace it. This will involve figuring out how existing players and emulators work and porting it. I haven't yet found an existing player that uses FMOD. My starting point is the MyNes source from http://sourceforge.net/projects/mynes/. There are two big steps between here and what I'm looking for. MyNes plays from a ROM, not NSF. So, I have to rip out the APU and get it to play NSF files. The MyNes APU uses SlimDX, so I have to convert that to FMOD.NET. I am really stuck about how to go about either of these, because I'm not that familiar with audio formats and it's hard finding resources online. So here are a few questions: From what I can tell from the NSF spec at http://kevtris.org/nes/nsfspec.txt, it's just contains the relevant memory section of the ROM, plus the header. If anyone can verify or correct this that would be great. The emulator APU uses data from the rest of the emulator to play, including things like cycle counts. I'm not sure what replaces this in a standalone player. Can't I just load all the music data at once into a stream and play it? Joining #1 and #2, does the header data from the NSF substitute for some of the ROM data in the emulator code? Using FMOD, will I be following the usercreatedsound example for loading a stream? And does this format count as PCM? Specifically MyNes says PCM8. Any tips on loading / playing the stream in FMOD are appreciated. As an aside, I don't really understand the loading / playing sections of the spec I linked at all. It seems to apply to 6502 systems / emulators only and not to my situation. I know it's a long shot for anyone here to have enough experience in this area to help, but anything you can provide is definitely appreciated. A link to an existing .NET library that does this would be even better, but I don't believe one exists.

    Read the article

  • Playing NSF music in FMOD.net

    - by Tesserex
    So, as the title says, I want to be able to play NSF files using FMOD, because my project already uses FMOD and I'd rather not replace it. This will involve figuring out how existing players and emulators work and porting it. I haven't yet found an existing player that uses FMOD. My starting point is the MyNes source from http://sourceforge.net/projects/mynes/. There are two big steps between here and what I'm looking for. MyNes plays from a ROM, not NSF. So, I have to rip out the APU and get it to play NSF files. The MyNes APU uses SlimDX, so I have to convert that to FMOD.NET. I am really stuck about how to go about either of these, because I'm not that familiar with audio formats and it's hard finding resources online. So here are a few questions: From what I can tell from the NSF spec at http://kevtris.org/nes/nsfspec.txt, it's just contains the relevant memory section of the ROM, plus the header. If anyone can verify or correct this that would be great. The emulator APU uses data from the rest of the emulator to play, including things like cycle counts. I'm not sure what replaces this in a standalone player. Can't I just load all the music data at once into a stream and play it? Joining #1 and #2, does the header data from the NSF substitute for some of the ROM data in the emulator code? Using FMOD, will I be following the usercreatedsound example for loading a stream? And does this format count as PCM? Specifically MyNes says PCM8. Any tips on loading / playing the stream in FMOD are appreciated. As an aside, I don't really understand the loading / playing sections of the spec I linked at all. It seems to apply to 6502 systems / emulators only and not to my situation. I know it's a long shot for anyone here to have enough experience in this area to help, but anything you can provide is definitely appreciated. A link to an existing .NET library that does this would be even better, but I don't believe one exists.

    Read the article

  • Oracle User Productivity Kit Translation

    - by ultan o'broin
    Oracle's customers just love the User Productivity Kit (UPK). I hear only great things about it from our international customers at the Oracle Usability Advisory Board meetings too. The UPK is the perfect solution for enterprise applications training needs (I previously reviewed a fine book about UPK btw). One question I am often asked is how source content created using the UPK can be translated into another language. I spoke with Peter Maravelias, Principal Product Strategy Manager for UPK about this recently. UPK is already optimized for easy source-target translation already. There is even a solution for re-recording demos. Here's what you can do to get your source content into another language: Use UPK's ability to automatically translate events and actions. UPK comes with XML templates that allow you to accomplish this in 21 languages with a simple publishing action switch. These templates even deal with the tricky business of using gender-based translations. Spanish localization template sample Japanese localization template sample Use the Import and Export localization features to export additional custom content in a format like XLIFF, easily handled by translation tools. You could also export and import in Word format. Re-record the sound (audio) files that go with the recordings, one per screen. UPK's granular approach to the sound files means that timing isn't an option. Retiming demos isn't required. A tip here with sound files and XLFF-exported custom content is to facilitate translation context by avoiding explicit references to actions going on in the screen recordings. A text based storyboard with screenshots accompanying the sound files should also be provided to the translators. Provide a glossary of terms too. Use the re-record option in UPK to record any demo from a translated application. This will allow all the translated UI labels to be automatically captured. You may be required to resize any action events here due to text expansion issues. Of course, you will need translated data in the translated application too, so plan for this in advance. However, source-target language skills aren't required for the re-recording. The UPK Player itself, of course, is also available from Oracle along with content and doc in 21 languages. The Developer and Setup is also translated in a smaller number of languages. Check the Oracle UPK website for latest details. UPK is a super solution for global enterprise applications training deployments allowing source content to be translated into multiple languages easily. See this post on the UPK blog for more insight too!

    Read the article

  • Beat detection and FFT

    - by Quincy
    So I am working on a platformer game which includes music with beat detection. I am currently using a simple if the energy that is stored in the history buffer is smaller then the current energy there is a beat. The problem with this is that ofcourse if you use songs like rock songs where you have a pretty steady amplitude this isn't going to work. So I looked further and found algorithms splitting the sound into multiple bands using FFT. I then found this : http://en.literateprograms.org/Cooley-Tukey_FFT_algorithm_(C) The only problem I'm having is that I am quite new to audio and I have no idea how to use that to split the signal up into multiple signals. So my question is : How do you use a FFT to split a signal into multiple bands ? Also for the guys interested, this is my algorithm in c# : // C = threshold, N = size of history buffer / 1024 public void PlaceBeatMarkers(float C, int N) { List<float> instantEnergyList = new List<float>(); short[] samples = soundData.Samples; float timePerSample = 1 / (float)soundData.SampleRate; int sampleIndex = 0; int nextSamples = 1024; // Calculate instant energy for every 1024 samples. while (sampleIndex + nextSamples < samples.Length) { float instantEnergy = 0; for (int i = 0; i < nextSamples; i++) { instantEnergy += Math.Abs((float)samples[sampleIndex + i]); } instantEnergy /= nextSamples; instantEnergyList.Add(instantEnergy); if(sampleIndex + nextSamples >= samples.Length) nextSamples = samples.Length - sampleIndex - 1; sampleIndex += nextSamples; } int index = N; int numInBuffer = index; float historyBuffer = 0; //Fill the history buffer with n * instant energy for (int i = 0; i < index; i++) { historyBuffer += instantEnergyList[i]; } // If instantEnergy / samples in buffer < instantEnergy for the next sample then add beatmarker. while (index + 1 < instantEnergyList.Count) { if(instantEnergyList[index + 1] > (historyBuffer / numInBuffer) * C) beatMarkers.Add((index + 1) * 1024 * timePerSample); historyBuffer -= instantEnergyList[index - numInBuffer]; historyBuffer += instantEnergyList[index + 1]; index++; } }

    Read the article

  • 'Unable to mount Filesystem' Error

    - by Charles
    Trying to extract data from a 'bricked' Western Digital MyBook Live 2tb drive. I came across a forum that advised to use Ubuntu (booted from a CD) on my Macbook. Managed to download and create a boot CD for Ubuntu (like this little operating system btw). Booted the machine with the CD and plugged the drive (which I had extracted from it's casing and placed into a external USB SATA case & plugged to the laptop). The drive is seen by Ubuntu but each time I click on the drive, it gives me the following error: Unable to mount 2.0 TB Filesystem Error mounting: mount: wrong fs type, bad option, bad superblock on /dev/sdb4, missing codepage or helper program, or other error In some cases useful info is found in syslog -try dmesg | tail or so I am new to this and spent quite some time searching this site to see if I could find a solution to this problem without troubling anyone. I came up with a few that came close but some of the questioners mentioned that they had lost data...which scared me from going further. I need to basically extract 1 particular folder from the drive. If I can get to mount this volume 'sdb4', there is a folder called 'My_Work' which I need to back up. The rest I have/had a copy of. When I typed in dmesg | tail...I got several lines..but I think ones that are relevant are: [ 406.864677] EXT4-fs (sdb4): bad block size 65536 [ 429.098776] hfs: write access to a journaled filesystem is not supported, use the force option at your own risk, mounting read-only [ 439.786365] hfs: write access to a journaled filesystem is not supported, use the force option at your own risk, mounting read-only [ 445.982692] EXT4-fs (sdb4): bad block size 65536 [ 1565.841690] EXT4-fs (sdb4): bad block size 65536 I read somewhere to try/check 'sudo fdisk -l /dev/sdb4'. It gave me the following result: Disk /dev/sdb44: 1995.8 GB, 1995774623744 bytes 255 heads, 63 sectors/track, 242639 cylinders, total 3897997312 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdb4 doesn't contain a valid partition table This is where I reached and got frustrated and decided to try & get help on this without digging myself deeper into a hole! I understand that the answer may already be out there. If so, could someone please point me in the right direction. And if not, could someone please resolve (if possible) my situation!

    Read the article

  • Android: Voice Recording and saving audio

    - by user1320912
    I am working on application that will record the voice of the user and save the file on the SD card and then allow the user to listen to the audio again. I am able to allow the user to record his voice using the RecognizerIntent, but I cant figure out how to save the audio file and allow the user to hear the audio. I would appreciate it if someone could help me out. I have displayed my code below: // Setting up the onClickListener for Audio Button attachVoice = (Button) findViewById(R.id.AttachVoice_questionandanswer); attachVoice.setOnClickListener(new OnClickListener() { public void onClick(View v) { Intent voiceIntent = new Intent(RecognizerIntent.ACTION_RECOGNIZE_SPEECH); voiceIntent.putExtra(RecognizerIntent.EXTRA_LANGUAGE_MODEL, RecognizerIntent.LANGUAGE_MODEL_FREE_FORM); voiceIntent.putExtra(RecognizerIntent.EXTRA_PROMPT, "Please Speak"); startActivityForResult(voiceIntent, VOICE_REQUEST); } }); protected void onActivityResult(int requestCode, int resultCode, Intent data) { if(requestCode == VOICE_REQUEST && resultCode == RESULT_OK){ }

    Read the article

  • Ubuntu 12.04 - No sound - HELP!

    - by Bruno Tacca
    I'm panicking... my sound stopped working after I tried to set-up my notebook speakers, plus two headphone jacks... My idea was to multichannel the sound to 3 channels, built-in speakers, and sound-card 2 headphone jacks. After a couple efforts I did it with 2 channels, speakers and 1 headphone jack, but the other wasn't working. After more tries and tries, sound stop working. I just want my sound back... crying like a baby on the floor. And, if possible, but not necessary, a simple guide to active the 3 channels. xD I will post the diagnosis according to https://help.ubuntu.com/community/SoundTroubleshootingProcedure STEP 1 Did it, still no sound. STEP 2 Did it, still no sound. STEP 3 and #STEP 4 (I removed the log cause there is a limit of characters to be posted.) The log can be found here: https://answers.launchpad.net/ubuntu/+source/alsa-driver/+question/238653 STEP 5 Rebooted, still no sound. STEP 6 Did it. In the Output Devices tab, nothing is muted. I play a music with the Rhythmbox Music Player, I don't hear anything but in the pavucontrol I can see in the Built-in Audio Analog Stereo a sound bar shaking... but, no sound. STEP 7 In alsamixer, AlsaMixer v1.0.25 Card: HDA Intel PCH Chip: Creative CA0132 information View: F3:[Playback] F4: Capture F5: All Item: Headphone [dB gain: 25.00, 25.00] Then, I have 5 columns Headphone, Speaker, PCM, S/PDIF, S/PDIF Default PCM A little weird when I try to mute the Headphone and the Speaker, here what happens: Starting both unmutted, mutting headphone cause speaker being mutted automaticaly. Starting both unmutted, mutting speaker cause headphone being mutted automaticaly. Starting both mutted, possible to unmute both separately. STEP 8 I cannot hear sound on both (headphone and/or speaker). STEP 9 Dual boot... Restarted, windows was with sound at max volume. Restarted again, still no sound at ubuntu. I heard something when ubuntu started, a little noise, then silence again. The sound icon always start mutted, after unmutting, I have no sound. STEP 10 I dont have this command in my ubuntu. STEP 11 Tried at STEP 8, no sound. There are no problem with jumpers or hardware, cause I have sound working on windows. STEP 12 No way to open my alienware and loss the warranty x.X" STEP 13 I think it's loaded, judging my the logs STEP 14 Alienware M17xR4, the hardware is listed in the logs above, at STEP 4. There are two headphone hacks, one with just an headphone printed above, and the other with an headset (with mic) printed, there is a mic jack too, and a spdif (optical) too. STEP 15 I dont want to enable S/PDIF STEP 16 I never used the HDMI output, yet... Thanks in advance. I hope I listed all the information you need.

    Read the article

  • Testing background audio in the simulator

    - by Cactuar
    I'm experimenting with the new background audio service in iPhone OS 4.0 but I can't get it to work in the simulator. According to this page: iPhone Application Programming Guide: Executing Code in the Background it seems that all I have to do is add the a UIBackgroundModes key with an array containing audio to my Info.plist file and the audio my application plays should automatically continue when I switch to another app. I have done this but the audio still pauses as I switch to another app, when I switch back it continues where it left off. This is the code I'm using to play the sound: NSURL *url = [NSURL fileURLWithPath:[NSString stringWithFormat:@"%@/audio.mp3", [[NSBundle mainBundle] resourcePath]]]; NSError *error; audioPlayer = [[AVAudioPlayer alloc] initWithContentsOfURL:url error:&error]; audioPlayer.numberOfLoops = -1; if (audioPlayer == nil) NSLog(@"%@", [error userInfo]); else [audioPlayer play]; Has anyone gotten this to work? Could it be that it would work on an actual device and it's just a problem with the simulator? I'm a bit hesitant to install 4.0 on my phone since I've heard it's still very buggy. Wish I had another device to use only for development.

    Read the article

  • Custom flash mp3 player stopping in the middle of playing audio on windows nt ie6 system

    - by Charlotte Moller
    We have used a custom MP3 flash player for a lot of years on our website without any issues, but recently, a client of ours is reporting that the audio is playing for several seconds and then stopping. When they refresh the page or click play in the player again the audio plays fine. We are puzzled as to what could be causing this issue after this running successfully for our clients for so many years. The client system is Windows NT running IE6. Does anyone have any idea what could cause the audio to behave this way? Could audio drivers or the version of flash cause problems? We do not have flash programmers on our team so we are not even sure where to start looking within the flash code of the player. Any ideas?

    Read the article

  • Ubuntu + Wacom Intuos 4 + MyPaint HELP!

    - by Sativa
    Please keep in mind I'm not that computer savvy, but I will try any suggestion so please help me out! My tablet will stop working if the USB connection is ever broken, or the Ubuntu software is being updated. Sometimes it will stop working for no reason that I can see. The lights will still be on, but it won't be responsive. It doesn't work again until I restart the laptop with the tablet plugged in, which is grating if you have to do it every 25 min. or so... I'm not sure if the issue is with the port, the tablet/cable or the driver but any suggestions would be very welcome! Also, MyPaint is frequently having hiccups. It seems to save fine but at times it will randomly close down and when I open files they're often empty. They turn into 0Kb files and only contain a single empty layer. Also very grating, considering I lose days of work for no clear reason and without any heads up. Again, I'm not sure if the issue is with the port, the tablet/cable or the driver but any suggestions would be very welcome! The error message reads; Traceback (most recent call last): File "/usr/share/mypaint/gui/application.py", line 177, at_application_start(*junk=()) else: self.filehandler.open_file(fn) variables: {'fn': ('local', u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora'), 'self.filehandler.open_file': ('local', <bound method FileHandler.wrapper of <gui.filehandling.FileHandler object at 0x7fdb89063a10>>)} File "/usr/share/mypaint/gui/drawwindow.py", line 60, wrapper(self=<gui.filehandling.FileHandler object>, *args=(u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora',), **kwargs={}) try: func(self, *args, **kwargs) # gtk main loop may be called in here... variables: {'self': ('local', <gui.filehandling.FileHandler object at 0x7fdb89063a10>), 'args': ('local', (u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora',)), 'func': ('local', <function open_file at 0x7fdb8b397b90>), 'kwargs': ('local', {})} File "/usr/share/mypaint/gui/filehandling.py", line 231, open_file(self=<gui.filehandling.FileHandler object>, filename=u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora') try: self.doc.model.load(filename, feedback_cb=self.gtk_main_tick) except document.SaveLoadError, e: variables: {'self.doc.model.load': ('local', <bound method Document.load of <lib.document.Document instance at 0x7fdb8ab4f8c0>>), 'feedback_cb': (None, []), 'self.gtk_main_tick': ('local', <function gtk_main_tick at 0x7fdb8b397b18>), 'filename': ('local', u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora')} File "/usr/share/mypaint/lib/document.py", line 544, load(self=<lib.document.Document instance>, filename=u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora', **kwargs={'feedback_cb': <function gtk_main_tick>}) try: load(filename, **kwargs) except gobject.GError, e: variables: {'load': ('local', <bound method Document.load_ora of <lib.document.Document instance at 0x7fdb8ab4f8c0>>), 'kwargs': ('local', {'feedback_cb': <function gtk_main_tick at 0x7fdb8b397b18>}), 'filename': ('local', u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora')} File "/usr/share/mypaint/lib/document.py", line 772, load_ora(self=<lib.document.Document instance>, filename=u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora', feedback_cb=<function gtk_main_tick>) tempdir = tempdir.decode(sys.getfilesystemencoding()) z = zipfile.ZipFile(filename) print 'mimetype:', z.read('mimetype').strip() variables: {'zipfile.ZipFile': ('global', <class 'zipfile.ZipFile'>), 'z': (None, []), 'filename': ('local', u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora')} File "/usr/lib/python2.7/zipfile.py", line 770, __init__(self=<zipfile.ZipFile object>, file=u'/home/maria/Desktop/Drawings/WIPs/Sativa Chibi.ora', mode='r', compression=0, allowZip64=False) if key == 'r': self._RealGetContents() elif key == 'w': variables: {'self._RealGetContents': ('local', <bound method ZipFile._RealGetContents of <zipfile.ZipFile object at 0x7fdb9b952790>>)} File "/usr/lib/python2.7/zipfile.py", line 811, _RealGetContents(self=<zipfile.ZipFile object>) if not endrec: raise BadZipfile, "File is not a zip file" if self.debug > 1: variables: {'BadZipfile': ('global', <class 'zipfile.BadZipfile'>)} BadZipfile: File is not a zip file

    Read the article

  • Capture Flash Audio in 4.7 Edge?

    - by emcmanus
    Is there a way to capture plugin (Flash) audio before it gets to the sound card? I'd like to record plugin audio, hopefully without actually playing the sound. Capturing audio at the device level is an absolute last resort, as the application would pick up all system audio rather than just the Webkit plugin. I'm aware of the recent switch back from QTMultimedia; is this possible with phonon? I spent the night looking for some way to access the phonon graph via QWebFrame (or any of the QtWebkit widgets) -- and didn't turn up much. I also started digging through QTWebkit, particularly NPAPI, without success. For reference, I'm using the edge version of 4.7 (6aa50af000f85cc4497749fcf0860c8ed244a60e) This seems to be a fairly challenging problem. Any hints would be greatly appreciated.

    Read the article

  • Audio queue start failed

    - by mobapps99
    Hi , i'm developing a project which has both audio streaming and playing audio from file. For audio streaming i'm using AudioStreamer and for playing from file i'm using avaudioplayer. Both streaming and playing works perfectly as long as the app is not interrupted by a phone call or sms. But when a call/sms comes after dismissing the call when i try to restart streaming i'm getting the error "Audio queue start failed" . This happens only when i have used avaudioplayer at least once and after that used streaming. When the avaudioplayer obeject is not created , in this scenario the there is no problem with resuming streaming after dismissing the call. My guess is that some thing is wrong with audioqueue. Help is very much appreciated.......

    Read the article

  • Making a DVD video with a still image and PCM 16bit audio with ffmpeg

    - by João
    I'm trying to make a small video with a still image and a sound file playing in the background to pass it to dvdauthor and create a DVD. The command I'm using is this: ffmpeg -loop_input -i image.jpg -qscale 2 -i song.flac -aspect 4:3 -target pal-dvd -acodec pcm_s16le -shortest output.mpg However, the resulting video file doesn't have sound at all (testing it on VLC Player). I don't know if I can't combine "-acodec pcm_s16le" with "-target pal-dvd" to override the later, or if there is something else wrong with the command. If I try without the "-acodec pcm_s16le" parameter the video and audio works, I can even create a DVD ISO with it. However, the audio stays as AC3. I wanted to include with the video the lossless audio, not a compressed one. I suppose the DVD standart allows to have PCM audio in it, am I right?

    Read the article

  • How to get the default audio format of a TTS Engine

    - by Itslava
    In Microsoft TTS 5.1 or newer. The SpVoice.AudioOutputStream property says: The AudioOutputStream property gets and sets the current audio stream object used by the voice. Setting the voice's AudioOutputStream property may cause its audio output format to be automatically changed to match the text-to-speech (TTS) engine's preferred audio output format. If the voice's AllowAudioOutputFormatChangesOnNextSet property is True, the format change takes place; if False, the format remains unchanged. In order to set the AudioOutputStream property of a voice to a specific format, its AllowOutputFormatChangesOnNextSet should be False. It means a engine's always has a preferred audio output format. So, how can i get it.. i have not found any interface to get that attribute.

    Read the article

  • Access MP3 audio data independently of ID3 tags?

    - by kyl191
    Hi, this is a 2 part question. First off, is it possible to access the audio data in an MP3 independently of the ID3 tags, and secondly, is there any way to do so using available libraries? I recently consolidated my music collection from 3 computers and ended up with songs which had changed ID3 tags, but the audio data itself was unmodified. Running a search for duplicate files failed because the file changed with the ID3 tag change, but I think it should be possible to identify duplicate files if I just run a deduplication using the audio data for comparison. I know that it's possible to seek to a particular position past the ID3 header in the file, and directly read the data, but was wondering if there's a library that would expose the audio data so I could just extract the data, run a checksum on it, and store the computed result somewhere, then look for identical checksums. (Also, I'd probably have to use some kind of library when you take into account variable length headers.)

    Read the article

  • Displaylink USB show "Logo / Loading" on monitor

    - by Ken Le
    I tried with this problem for 2 years already. LOL, today, I install Ubuntu for I have to resolve it or I will back to stupid Windows 7. First, I have 3 monitors. My graphic card is support dual ( ATI Radeon ), so I have no problem on extend those multi monitor on VGA and DVI. The 3rd monitor is Displaylink USB. After installed everything required, when I reboot, the displaylink monitor show "Ubuntu ...." like logo / loading screen. I go to System Display , Detect monitor, it only show my 1st and 2nd, NO 3RD Displaylink. I can move my mouse between those 1st & 2nd, but the 3rd is only show the Ubuntu Screen. I press Ctrl+Alt+1, then screen switch to Displaylink USB 3RD monitor, but its "Terminal" not a desktop. Then I press Ctrl+Alt+7 , the screen switch back to my 1st, 2nd, and the displaylink 3rd is witch back to Logo / Ubuntu again. This is my /etc/X11/xorg.conf : Section "ServerLayout" Identifier "X.org Configured" Screen 0 "aticonfig-Screen[0]-0" 0 0 Screen 1 "DisplayLinkScreen" Leftof "aticonfig-Screen[0]-0" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "/usr/share/fonts/X11/misc" FontPath "/usr/share/fonts/X11/cyrillic" FontPath "/usr/share/fonts/X11/100dpi/:unscaled" FontPath "/usr/share/fonts/X11/75dpi/:unscaled" FontPath "/usr/share/fonts/X11/Type1" FontPath "/usr/share/fonts/X11/100dpi" FontPath "/usr/share/fonts/X11/75dpi" FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" FontPath "built-ins" EndSection Section "Module" Load "glx" Load "dri2" Load "dbe" Load "dri" Load "record" Load "extmod" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "aticonfig-Monitor[0]-0" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" EndSection Section "Monitor" Identifier "DisplayLinkMonitor" EndSection Section "Monitor" Identifier "0-DFP1" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1680x1050" Option "TargetRefresh" "60" Option "Position" "0 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Monitor" Identifier "0-CRT2" Option "VendorName" "ATI Proprietary Driver" Option "ModelName" "Generic Autodetecting Monitor" Option "DPMS" "true" Option "PreferredMode" "1920x1080" Option "TargetRefresh" "60" Option "Position" "1680 0" Option "Rotate" "normal" Option "Disable" "false" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "NoAccel" # [<bool>] #Option "SWcursor" # [<bool>] #Option "Dac6Bit" # [<bool>] #Option "Dac8Bit" # [<bool>] #Option "BusType" # [<str>] #Option "CPPIOMode" # [<bool>] #Option "CPusecTimeout" # <i> #Option "AGPMode" # <i> #Option "AGPFastWrite" # [<bool>] #Option "AGPSize" # <i> #Option "GARTSize" # <i> #Option "RingSize" # <i> #Option "BufferSize" # <i> #Option "EnableDepthMoves" # [<bool>] #Option "EnablePageFlip" # [<bool>] #Option "NoBackBuffer" # [<bool>] #Option "DMAForXv" # [<bool>] #Option "FBTexPercent" # <i> #Option "DepthBits" # <i> #Option "PCIAPERSize" # <i> #Option "AccelDFS" # [<bool>] #Option "IgnoreEDID" # [<bool>] #Option "CustomEDID" # [<str>] #Option "DisplayPriority" # [<str>] #Option "PanelSize" # [<str>] #Option "ForceMinDotClock" # <freq> #Option "ColorTiling" # [<bool>] #Option "VideoKey" # <i> #Option "RageTheatreCrystal" # <i> #Option "RageTheatreTunerPort" # <i> #Option "RageTheatreCompositePort" # <i> #Option "RageTheatreSVideoPort" # <i> #Option "TunerType" # <i> #Option "RageTheatreMicrocPath" # <str> #Option "RageTheatreMicrocType" # <str> #Option "ScalerWidth" # <i> #Option "RenderAccel" # [<bool>] #Option "SubPixelOrder" # [<str>] #Option "ClockGating" # [<bool>] #Option "VGAAccess" # [<bool>] #Option "ReverseDDC" # [<bool>] #Option "LVDSProbePLL" # [<bool>] #Option "AccelMethod" # <str> #Option "DRI" # [<bool>] #Option "ConnectorTable" # <str> #Option "DefaultConnectorTable" # [<bool>] #Option "DefaultTMDSPLL" # [<bool>] #Option "TVDACLoadDetect" # [<bool>] #Option "ForceTVOut" # [<bool>] #Option "TVStandard" # <str> #Option "IgnoreLidStatus" # [<bool>] #Option "DefaultTVDACAdj" # [<bool>] #Option "Int10" # [<bool>] #Option "EXAVSync" # [<bool>] #Option "ATOMTVOut" # [<bool>] #Option "R4xxATOM" # [<bool>] #Option "ForceLowPowerMode" # [<bool>] #Option "DynamicPM" # [<bool>] #Option "NewPLL" # [<bool>] #Option "ZaphodHeads" # <str> Identifier "Card0" Driver "radeon" BusID "PCI:5:0:0" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "ShadowFB" # [<bool>] #Option "Rotate" # <str> #Option "fbdev" # <str> #Option "debug" # [<bool>] Identifier "Card1" Driver "fbdev" BusID "PCI:5:0:0" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "ShadowFB" # [<bool>] #Option "DefaultRefresh" # [<bool>] #Option "ModeSetClearScreen" # [<bool>] Identifier "Card2" Driver "vesa" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" Option "Monitor-DFP1" "0-DFP1" Option "Monitor-CRT2" "0-CRT2" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "DisplayLinkDevice" Driver "displaylink" Option "fbdev" "/dev/fb1" Option "ShadowFB" "off" EndSection Section "Screen" Identifier "aticonfig-Screen[0]-0" Device "aticonfig-Device[0]-0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Virtual 3600 1920 Depth 24 EndSubSection EndSection Section "Screen" Identifier "DisplayLinkScreen" Device "DisplayLinkDevice" Monitor "DisplayLinkMonitor" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1920x1080" EndSubSection EndSection

    Read the article

  • External USB HD issues with a twist (works on Windows7 but not XP)

    - by Eruditass
    I have this older external USB HD, 160 GB. I was using it to copy my Steam games to another computer. On the source computer, Windows 7 64-bit, everything worked fine. Drive reported no errors, had no hiccups, etc. Plugging it into the Windows XP 32-bit computer, it worked fine for looking through the files, moving files around on it (no real reading/writing, just modifying the filesystem table). However, when copying files from it to my internal HD, after a couple seconds to tens of minutes (seemingly random times), the USB device becomes unrecognized and it reports a delayed write error. Events in system log go like this, chronologically: (number times displayed)xSource (Event ID): "message" 2xdisk (51): An error was detected on device \Device\Harddisk1\D during a paging operation. 1xftdisk (57): The system failed to flush data to the transaction log. Corruption may occur. 1xApplication popup (26): Windows - Delayed Write Failed : Windows was unable to save all the data for the file E:\$Mft. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. 1xntfs (50): {Delayed Write Failed} Windows was unable to save all the data for the file . The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere. These repeat for a while, then there is 10+ disk messages or ftdisk messages. Other notes: This occurs on random files at random times. This problem cannot be replicated on the Windows 7 source machine when copying from the HD to a different location on its local disk chkdsk /f was run and found no errors. chkdsk /f/r has the delayed write issue. drive was set to quick removal. Setting to performance in device manager yielded same result I am not writing anything to the USB external drive, so I am not sure why there is even a delayed write error (writing file access times?) local Windows XP was chkdsk'd without problems Windows XP machine has no problems with other USB HD's Various USB ports were attempted Rebooting did not help Occurs with SyncToy as well as windows explorer SMART status is good on both local drive and the external one Lack of gaming is making me cranky

    Read the article

< Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >