Search Results

Search found 7164 results on 287 pages for 'powerline networking'.

Page 105/287 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• Need assistance setting up Linux Router with 2 public lans

  - by user195407

  I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

  Read the article

• Route traffic from one VPN to a second VPN

  - by Dominic

  I have set up an OpenVPN server on my windows 7 64-bit PC. I also have a subscription to a VPN service. My aim is to be able to connect my android phone to the VPN server on my PC, and then route all traffic through the VPN service. I have a NetGear WPN824 router. I can get it working if I my phone is on my local network. Then I can connect my phone to the VPN server using the local IP address of my PC. In Network Connection in the control panel, I share the connection used by the VPN service with the connection used by the VPN server. Then when I browse the internet on my phone, all traffic goes through the VPN service. Very nice. But if my phone is outside my local network, so I have to connect my phone to the local VPN using my PC's external IP address, then this method doesn't work. If I connect my PC to the VPN service and then try to connect my phone to my own VPN, it just doesn't connect (the initial TLS handshake times out). If I connect my phone to the local VPN first, then this connection is lost as soon as I connect my PC to the VPN service. Does anybody know how I can get this working? Many thanks Dominic

  Read the article

• Display wireless channels currently in use

  - by DrStalker

  Is there any windows utility to display the wireless channels are currently in use by the available wireless networks? I'd like to be able to see what existing channels are using so I can try to minimize interference on a new access point without a lot of trial and error.

  Read the article

• Setting up 802.1X wireless connection on OSX

  - by hizki

  I am an OSX user, I have Snow Leopard 10.6.5 and an updated AirPort. I am trying to connect to my university's wireless network, but it has a complex security that I am having trouble defining... Here there are instructions for connecting with Windows XP, Windows 7 and Linux. Can someone please instruct me what should I do to set up this network on my MAC? Thank you. P.S. I have had previous success in setting up this network, but I have no idea what I did that made it work. Since I updated my AirPort it worked only seldomly and very slowly... Before the update, even when it worked it never remembered my password.

  Read the article

• Change Fedora 12 Hostname through gui

  - by drozzy

  How can I change fedora 12 hostname using gui tools (network connections) only, without editing config files? All I can see right now if I select "Manual" in IPv4 settings is "DNS servers" or DHCP client ID, neither of which sounds like "domain/hostname" combination. Tips?

  Read the article

• Change Fedora 12 Hostname through gui

  - by drozzy

  How can I change fedora 12 hostname using gui tools (network connections) only, without editing config files? All I can see right now if I select "Manual" in IPv4 settings is "DNS servers" or DHCP client ID, neither of which sounds like "domain/hostname" combination. Tips?

  Read the article

• Connection drops while transferring large files to one server on a network

  - by Charlotte

  My company has two sites, each with their own LAN, using site to site VPN tunnel to connect the two sites. When transferring files (especially larger files) from site1 to site2 server1, the file transfer fails. I don't think this can be a VPN issue because transferring the same files to site2 server2 which is on the same network as server1 works fine. Pings to server1 and server2 at site2 from site1 are about the same, mostly 19/20ms with the odd one up to 50ms. As server1 is DB server with a high load I thought the NIC maybe overloaded, but a transfer from site2 server1 to site2 server2 works fine, and that uses the same NIC on server1 as transfers from site1 to site2 server1. The servers are both Windows Server 2003 VMs with VMXNET 3 NICs. Site2 Server1 route print: IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 28 9b ...... vmxnet3 Ethernet Adapter #2 0x10004 ...00 50 56 99 18 97 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.18 10 10.10.10.0 255.255.255.0 10.10.10.70 10.10.10.70 10 10.10.10.70 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.18 172.20.10.18 10 172.20.10.18 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.18 172.20.10.18 10 224.0.0.0 240.0.0.0 10.10.10.70 10.10.10.70 10 224.0.0.0 240.0.0.0 172.20.10.18 172.20.10.18 10 255.255.255.255 255.255.255.255 10.10.10.70 10.10.10.70 1 255.255.255.255 255.255.255.255 172.20.10.18 172.20.10.18 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site2 Server2 route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x10003 ...00 50 56 99 15 00 ...... vmxnet3 Ethernet Adapter =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 172.20.10.1 172.20.10.114 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 172.20.10.0 255.255.255.0 172.20.10.114 172.20.10.114 10 172.20.10.114 255.255.255.255 127.0.0.1 127.0.0.1 10 172.20.255.255 255.255.255.255 172.20.10.114 172.20.10.114 10 224.0.0.0 240.0.0.0 172.20.10.114 172.20.10.114 10 255.255.255.255 255.255.255.255 172.20.10.114 172.20.10.114 1 Default Gateway: 172.20.10.1 =========================================================================== Persistent Routes: None Site1 Server route print: =========================================================================== Interface List 14...00 50 56 93 00 0b ......vmxnet3 Ethernet Adapter #2 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.168.1 192.168.168.118 261 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.168.0 255.255.255.0 On-link 192.168.168.118 261 192.168.168.118 255.255.255.255 On-link 192.168.168.118 261 192.168.168.255 255.255.255.255 On-link 192.168.168.118 261 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.168.118 261 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.168.118 261 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.168.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 261 fe80::/64 On-link 14 261 fe80::3c6b:996f:ef36:ee76/128 On-link 1 306 ff00::/8 On-link 14 261 ff00::/8 On-link =========================================================================== Persistent Routes: None tracert from site1 to site2 server1: Tracing route to server1 [172.20.10.18] over a maximum of 30 hops: 1 19 ms 19 ms 19 ms server1 [172.20.10.18] Trace complete. tracert from site2 server1 to site1: When this was run it went to the external IP of site2, then to a couple of external ips of the isp, then times out. Can anyone suggest any troubleshooting steps? Thanks, Charlotte.

  Read the article

• Good Wireless Range Extender

  - by Joseph Sturtevant

  Can anyone recommend a good wireless (802.11g) range extender? I would like to find something that will provide reliable wireless to areas of the building that aren't covered or get poor reception. I would also like a product that won't require big changes to my current wireless setup (multiple APs with a wireless controller are out). Latency and bandwidth aren't terribly important. Does anyone have experience with a product like this?

  Read the article

• What decent small-office level routers are there

  - by Glenn Slaven

  So let's say I have a network of less than 20 computers including a server that needs to be accessed externally. What router/firewall solutions would you recommend? It can be either hardware or software and would need to be able to do NAT Firewall DMZ Native VPN if possible Some form of network bandwidth monitoring Update: I've accepted the answer I liked but this question probably doesn't have a definitive answer, it would depend on your requirements. Please leave more suggestions with an explanation as to why it works well in your situation.

  Read the article

• Multiple Internet connections, multiple networks and split access in Linux

  - by Swapneel Patnekar

  I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

  Read the article

• Wireless Repeating with two Netgear N750 (WNDR4300)

  - by jomo1911

  I have a Netgear N750 as my main router, which connects to the internet via a modem. I have a second Netgear N750 which I want to use to repeat the wireless signal of the main router. I logged in to routerlogin of my main router (192.168.1.1) and set up the "Wireless Repeating Function". I set it as the "Wireless Base Station" and filled in the MAC adress of my second Netgear N750. Then I logged in to routerlogin of my second router and set it up as the "Wireless Repeater", I gave it the IP 192.168.1.11 and filled in the MAC adress of the base station. During the setup of the second router (Repeater) I had to disable all security functions. If I connect to the repeaters' WLAN signal, I get no internet connection. Maybe you can help me, thanks

  Read the article

• SCM8014 to FVS338

  - by Jack

  I have a SMC8014 Router/Modem that Comcast provided me with their business class service. It was not filtering malicious traffic as aggressively as I had hoped, so I purchased a NetGear ProSafe FVS338, and put this behind the SMC8014, and all my machines behind that. After some brief configuration, all machines can see out to the internet. I also have a single web server, and I have not been able to configure things so that incoming requests can reach it. This is where I need help! I would like to have the FVS339 do NAT, so that I can assign a 192.168 address to my webserver. I've tried everything I know of, and I can't get things going. I set the SMC8014 to have a LAN facing IP of 10.0.0.1, and I assigned the FVS339 a WAN facing IP of 10.0.0.2. I would like to be able to tell the SMC8014 to just forward all traffic to 10.0.0.2, but I haven't had any success. In my (unfortunately limited) understanding, what I probably want here is a static route, but I don't know how to cofigure one, or if this is really what I want. The SMC8014 wants a Destination IP, a Subnet Mask and a Gateway IP. Any help would be appreciated.

  Read the article

• Best practice for assigning private IP ranges?

  - by Tauren

  Is it common practice to use certain private IP address ranges for certain purposes? I'm starting to look into setting up virtualization systems and storage servers. Each system has two NICs, one for public network access, and one for internal management and storage access. Is it common for businesses to use certain ranges for certain purposes? If so, what are these ranges and purposes? Or does everyone do it differently? I just don't want to do it completely differently from what is standard practice in order to simplify things for new hires, etc.

  Read the article

• Multiple access points for the same SSID ?

  - by krosenvold

  I need to upgrade my existing wireless infrastructure and this time I want 2 access points to cover my house, since I get blind spots no matter what with a single AP, I have physical cabling to my central network available for both access points. But I would really like these two to interoperate seamlessly as a single SSID. How do I do this and what are the features the new AP's I'm buying need to support ? (Product recommendations are welcome ;)

  Read the article

• What Wireless Router/ADSL Modem to get? N-band a must!!

  - by JJarava

  I'm looking for a Dual-N band Router OR ADSL Gateway and I'd like some recommendations. Situation: I have a 802.11b/g ADSL gateway provided by my telco, but the WIFI signal won't cover all the house (especially the living-room, so my tv-connected Mac Mini has poor to no internet access). So I'm looking to either replace the DSL modem with a N-enabled one, or to add a Router to the mix. I've had a modem+router setup for many years, and I know the advantatges (double NAT, double FW = more security) and issues (more complex to troubleshoot, two possible points of failure), so I'd rather live with a single (ADSL Gateway) device, if possible. Requirements: Dual-N Band (300 Mbs WIFI) 1 GB Ethernet ports ADSL2+ support (if it's a ADSL gateway, which would be desirable) "Best" range and speed possible Nice to have: USB port to share disks/printers on the network Media streaming I've been a long time user of Linksys, so googling around I found the WRT610N (http://www.linksysbycisco.com/US/en/products/WRT610N) for a "Pure Router" perspective, and it's one of those that Linksys styles "N++" (http://www.linksysbycisco.com/US/en/promo/Promotion-Go-Wireless?stepname=Promotion-Step-Go-Wireless-High-Performance) But I haven't been able to find similar "ADSL" gateways. I've found the WAG320N, but there is little to no info in the Linksys site (i.e., i don't know if it's Dual Band, or if it has GB ethernet) Any opinions/recommendations of other products/suggestions are more than welcome.

  Read the article

• NFSv3 Asynchronous Write Depends on Block Size?

  - by Joe Swanson

  I am trying to figure out if my NFSv3 deployment is performing SAFE asynchronous writes. I suspect that it is doing strictly synchronous writes, as I am getting poor performance in general. I used Wireshark to look at the 'stable' flag in write calls, and look for 'commit' calls. I noticed that, with especially large block sizes, writes to appear to be performed asynchronously: dd if=/dev/zero of=/proj/re3/0/zero bs=2097152 count=512 However, smaller block sizes appear to be performed strictly synchronously: dd if=/dev/zero of=/proj/re3/0/zero bs=8192 count=655360 What gives? How does the client decide whether to tell the server to perform writes synchronously or asynchronously? Is there any way I can get smaller block sizes to be performed asynchronously?

  Read the article

• Oracle 11g network configuration

  - by Kylo

  I installed Oracle 11g Enterprise Edition on my Windows 7 Pro. My problem is that I cannot log into database from other host (local network). When I connect to database using Oracle SQLdeveloper everything is ok as long as I specify 'localhost' in connection configuration. However, when I change it to '192.168.0.190' which is my host IP address I get 'The Network Adapter could not establish the connection'. I get the same error when logging in from other host in local network. What is the problem?

  Read the article

• VoIP - need setup ip network with our SIP operator

  - by evgeniy.labusnkiy

  Need to make next one: for ex i'm now in UAE, but i need to make a call to my girlfriend who is in Ukraine. I need to find the way how can i make the connection to my home router and make the call from VoIP gateway using my standard phone network in Ukraine. I have some imagination about this, to do like this: Connect to router or VoIP gateway (how? soft?) using inet - Gateway make a call using standard phone line in my country. Any ideas? Best practice? What devices i need to make this? Pay attention that i don't want to use any SIP providers. Thats a lot!

  Read the article

• windows Home Server backup error

  - by domen

  I've finally built my WHS, but some other problems have showed up. I've googled, binged and searched SU with no success. The problem is following: at the moment I've got a Win7 laptop and Win7 PC, which should be backed up by the WHS. Laptop is backed up just fine with no issues, but when I try to manually backup the PC, after "backup is starting" message, when backup service should be monitoring changes on partitions, PC gets disconnected from the home network and thus, the backup process is stuck. Disabling/enabling network adapter gets PC back on the network. The only thing I've tried was reinstalling connector software. no success. Also, I've downloaded connector troubleshooter and only thing it says is "DHCP server was not found". I'm not good with networks, so I couldn't figure out what could that indicate (all computers in the network are assigned static IPs). Any ideas what the problem can be? I can provide any additional information, I'm just not sure what may be helpful right now. Thanks.

  Read the article

• ISP Load Balancing with ISA 2006

  - by Bill Best

  I understand that ISA 2006 has an integrated Network Load Balancing feature. We also recently acquired a second internet line through a second service provider. I know it is possible to purchase a NLB router for using both incoming lines but this is not the route we would like to take if at all possible. Thus, is it possible to have two ISA 2006 servers each with there own external connection, Load balanced to be viewed as one gateway? My thought was to have two ISA servers each with three NICs, one external, one internal and one for cross communication. I am under the impression that this should work but was hoping someone else has had experience with it.

  Read the article

• Download - Upload is too slow on Centos

  - by Mehdi

  My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

  Read the article

• The RTL8111/8168B NIC under Linux and the r8168 driver

  - by nik

  So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• What are the challenges when my enterprise desires to move the processing component of an applicatio

  - by Berkay

  Assume that i have an enterprise accounting application that consists of a front-end interface, a processing tier, and a back-end database. This is an application that contains private business data, and thus is traditionally run in a secure private network environment within the enterprise. What are the challenges that appear when my enterprise desires to move the processing component of this application to a cloud computing data center in order to achieve greater scalability or to reduce IT costs ? Pls note: do i have to make significant changes to my own infrastructure to enable external access to formerly private resources? do i have to modify the application code to handle new network topology ? thanks, if you give your answers in a simple manner, really appreciated.

  Read the article

• Sniffing at work- How to detect

  - by coffeeaddict

  Because of the place I work has some real issues (people) especially in IT and the owner, I wonder if we are being sniffed. Is there any way to tell if on a Vista 64-bit machine: 1) In system logs some identification that would tell me that someone might log into my PC such as an Admin 2) Something in the logs that would give me a flag about maybe I'm being monitored some other way? 3) How can I be sure that my gmail, hotmail, and chat is not being sniffed. I know there are things like Simp, etc. I'm talking about specific hidden system signs either in registry or logs. Obviously I'm not going to raise any suspicion by me asking our network admin. I don't trust anyone at this company. is there a good way to basically monitor for this as an end user? Could someone log in and basically watch me work and if so, would there be any goodies left behind for me to find out if this has happened other than visual signs which would not be present...maybe some running processes?

  Read the article

• How can I find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >