Search Results

Search found 3222 results on 129 pages for 'mercurial queue'.

Page 106/129 | < Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >

  • Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

    - by Bo102010
    (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

    Read the article

  • VMware vSphere 4.1 and BackupExec 2010

    - by Josh
    I'm sure a common problem with most shops is backups, their size, and the window in which you have to back up the data. What we are working with: VMware vSphere 4.1 Cluster PS4000XV Equallogic Storage Array (1.6TB Volume dedicated for Backup to Disk) Physical Backup Server with a single LTO4 drive. BackupExec 2010 R3 with the following agents, Exchange, SQL, Active Directory, VMware. Dual Gigabit MPIO Connections between all devices (Storage Array, Backup Server, VM Hosts) What we would like to accomplish: I would like to implement an efficient Backup to Disk to Tape solution where all of our VMs are backed up to the Storage Array first, and then once completely backed up to the array are replicated to tape. In the event we needed to recover, we would be able to do so directly from tape. Where we are at currently. Of the several ways I have setup the jobs in Backup Exec 2010 R3 the backup jobs all queue up at the same time, as soon as a job is finished backing up to disk it then starts that same job to tape, but pulling from the original source instead of the designated B2D location. I understand that I could create a job that backs up the "Backup to Disk" folder to tape, but in the event of restoration, I would first need to stage the data in the B2D folder before I could restore the VM. I would really like to hear from individuals in similar situations. Any and all comments and critiques are appreciated.

    Read the article

  • Shared printer stops working on clients but not host computer

    - by Tony
    I have a Brother MFC-7420 USB all-in-one laser printer. It is plugin via USB to my Windows 7 x64 machine. I have it shared to a few users on my home network. My wife's laptop running Vista x64 can normally print fine to the printer. However it seems that every day or two, when she pushes print on a something it just sits in her laptop's print queue and never makes it to my desktop. The only thing that seems to fix this is if she restarts her laptop. Not a big deal but this problem is sort of annoying. I don't know if this affects but the laptop is put into hibernate at night and I turn my desktop off at night. Does anyone know why this happens and if there is something easy to do to fix the problem besides restart the computer? EDIT: I was thinking that maybe my wife's laptop loses its connection to the printer. Is there a way to reset a connection to a shared printer? Or maybe reauth with the printer?

    Read the article

  • Parallel Environment (PE) on Sun Grid Engine (6.2u5) won't run jobs: "only offers 0 slots"

    - by Peter Van Heusden
    I have Sun Grid Engine set up (version 6.2u5) on a Ubuntu 10.10 server with 8 cores. In order to be able to reserve multiple slots, I have a parallel environment (PE) set up like this: pe_name serial slots 999 user_lists NONE xuser_lists NONE start_proc_args /bin/true stop_proc_args /bin/true allocation_rule $pe_slots control_slaves FALSE job_is_first_task TRUE urgency_slots min accounting_summary FALSE This is associated with the all.q on the server in question (let's call the server A). However, when I submit a job that uses 4 threads with e.g. qsub -q all.q@A -pe serial 4 mycmd.sh, it never gets scheduled, and I get the following reasoning from qstat: cannot run in PE "serial" because it only offers 0 slots Why is SGE saying "serial" only offers 0 slots, since there are 8 slots available on the server I specified (server A)? The queue in question is configured thus (server names changed): qname all.q hostlist @allhosts seq_no 0 load_thresholds np_load_avg=1.75 suspend_thresholds NONE nsuspend 1 suspend_interval 00:05:00 priority 0 min_cpu_interval 00:05:00 processors UNDEFINED qtype BATCH INTERACTIVE ckpt_list NONE pe_list make orte serial rerun FALSE slots 1,[D=32],[C=8], \ [B=30],[A=8] tmpdir /tmp shell /bin/sh prolog NONE epilog NONE shell_start_mode posix_compliant starter_method NONE suspend_method NONE resume_method NONE terminate_method NONE notify 00:00:60 owner_list NONE user_lists NONE xuser_lists NONE subordinate_list NONE complex_values NONE projects NONE xprojects NONE calendar NONE initial_state default s_rt INFINITY h_rt 08:00:00 s_cpu INFINITY h_cpu INFINITY s_fsize INFINITY h_fsize INFINITY s_data INFINITY h_data INFINITY s_stack INFINITY h_stack INFINITY s_core INFINITY h_core INFINITY s_rss INFINITY h_rss INFINITY s_vmem INFINITY h_vmem INFINITY,[A=30g], \ [B=5g]

    Read the article

  • How to find out which program a default beep is coming from in Windows 7?

    - by leeand00
    There's a "default beep" (as defined in System Sounds) that emanates from my computer every so often. It kind of goes like this (where each number is a "default beep" sound): 1, 2, 3, 4, 5. So there's a distinct pattern to it. I thought I had this figured out a way to figure out what was happening by going to Control Panel-Ease of Access-Ease of Access Center-Replace sounds with visual cues But that just isn't the case. Whichever window I click on, that one displays the visual queue when this happens. It's driving me crazy, and I can't figure out which program is causing this. Update: it appears to only happen on one user profile on the computer...does that help? Update 2: Discovered that this sound was coming from a utility on my laptop called ASUS NB Probe; I'm certain that it is emanating from this program because the error message displayed by it changes in sync with the sound playing. Apparently the S.M.A.R.T. feature of my hard drive was reporting an issue. It displays the issue for a brief second and then makes it disappear, I'll have to keep watching it to see what it says, but I believe is says something about a read. I have an external hdd connected with eSATA to a container of sorts (BlacX) that you can plug two hdds into. I have one hdd attached and it's a Western Digital WD1001FALS - 00E8B0 Thanks again! Now I'm off to go around the Internet and report on this...since I posted it so many places!

    Read the article

  • MySQL taking a long time to start

    - by Dscoduc
    I'm running Windows Server 2008 with MySQL installed and every time I reboot the server the MySQL Service doesn't start right away. A look into the Windows Eventlog shows that the MySQL Service was hung at startup. Looking at the Services.msc console shows the service state at Starting... Eventually, like 10 minutes, the MySQL Service actually finishes the startup process and the database becomes available for my Wordpress server... I looked at the MySQL .err files and didn't find anything that would indicate a delay in the statup process... Can anyone suggest a way to determine what is causing the delay, and more importantly, how to prevent the delay in the MySQL Startup? UPDATE: Here is the .err log contents from the shutdown to the startup complete. Notice the startup begins at 10:30:00 and the MySQL isn't ready for connections until 10:47:14, a full 17 minutes later: 100322 10:27:06 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Normal shutdown 100322 10:27:06 [Note] Event Scheduler: Purging the queue. 0 events 100322 10:27:06 InnoDB: Starting shutdown... 100322 10:27:08 InnoDB: Shutdown completed; log sequence number 4 3854351346 100322 10:27:08 [Warning] Forcing shutdown of 1 plugins 100322 10:27:08 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: Shutdown complete 100322 10:30:00 [Note] Plugin 'FEDERATED' is disabled. 100322 10:30:01 InnoDB: Started; log sequence number 4 3854351346 100322 10:47:14 [Note] Event Scheduler: Loaded 0 events 100322 10:47:14 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld: ready for connections. UPDATE 2: MySQL is configured as a service (part of the install process, nothing I did) and executes the following syntax (as it appears in the registry): "C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld" --defaults-file="C:\Program Files\MySQL\MySQL Server 5.1\my.ini" MySQL

    Read the article

  • Slow performance on VMWare Linux server after Tomcat install

    - by Loftx
    We have a VMWare ESXi 4.1 server hosting a number of Linux and Windows guests. Recently a new Linux guest was added to this server and seemed to be performing well. Tomcat and some other applications on this server were then installed which seem to have caused the server to run really slowly without any obvious resource issues. Slow performance include: The time taken to bring up the password prompt over ssh takes a few seconds when it was previously instantaneous. The time taken to unzip a zip file which was previously a few seconds now takes around 30 seconds The time taken to compile vmware tools has increased by similar factors Both the VMWare console and monitoring commands don't report any issues with high CPU or memory usage but something is obviously slowing the server down somehow. Does anyone have any ideas what may be causing this issue and how it can be resolved? Thanks, Tom Edit As per your questions I’ve looked at some of the performance indicators on both the VM host and VM guest indicated. Firstly I tried reserving the full amount of memory (3gb) for this VM – no other machines on this server have any memory reservation. The swap in rate and swap out rate for the VM host and guest are now both zero. Balloon memory on the guest is zero and on the host is 3.5gb (total memory on the host is 12gb) The swap rate for the guest is also zero. Swap used by the host is 200mb on average. Compression and decompression rates for the host and guest are zero. Command aborts for the host are zero. Read latency is very low – maximum 10ms average 0.8ms. Write latency is higher – a few spikes to 170ms but mostly around 25ms – is this bad? Queue command latency is zero . Physical disk read latency averages 5ms but often 10ms Physical disk write latency averages 15ms but is often 20ms I hope this helps - let me know if you need any more information.

    Read the article

  • Move postfix maildir files from one mail server to another

    - by Tauren
    I have a new mail server configured as described in this howto: http://howtoforge.com/virtual-users-domains-postfix-courier-mysql-squirrelmail-ubuntu-9.10 I also have an ancient mail server configured very similarly (using the same HOWTO, just for Fedora Core 6, if I recall correctly). Earlier today I had to switch from the old server to the new one, and the old one is no longer online. However, after I had migrated everything and switched it all over, I discovered a bunch of undelivered mail in the queue. It got delivered to the local mailboxes on the old server, so now there are a bunch of messages on it that I'd like to move to the new server. The new server has already received new messages, so I need to merge the files together somehow. For each user with an email of [email protected], there are files like this on both servers: /home/vmail/customer.com/username/maildirsize /home/vmail/customer.com/username/courierpop3dsizelist /home/vmail/customer.com/username/new/1271481177.Vca01I6006bM580357.mailhost.mydomain.com Can I simply copy the hundreds of files in the various new directories on the old server to the corresponding new directories on the new server? Will the maildirsize and courierpop3dsizelist files get updated automatically, or do I need to do something to update them?

    Read the article

  • In GNU Screen, Recalled bash history command displays one character position to the left of actual location

    - by vergueishon
    I am running Red Hat 5 32-bit (2.6.18-194.26.1.el5). The issue is that when I recall any previous command in bash's history, the first character in the command is displayed immediately after the shell prompt, without any intervening space, likeso: \[me@mymachine tmp]$man mysql If I enter a Ctrl-C, and retype the command, it looks likeso: \[me@mymachine tmp]$ man mysql This makes recalling a command and editing it before re-entering a real pain. Basically, if I try to edit a recalled command, my changes occur one character position to the left (I believe) of what I see on the screen. It's a bit tedious to describe, and appears to only happen with commands with a large number of arguments. UPDATE: The contents of /etc/sysconfig/bash-prompt-screen, 1 #!/bin/bash 2 echo -n $'\033'"_${USER}@${HOSTNAME%%.*}:${PWD/#$HOME/~}"$'\033\\\\' and the contents of /etc/bashrc, 24 screen) 25 if [ -e /etc/sysconfig/bash-prompt-screen ]; then 26 PROMPT_COMMAND=/etc/sysconfig/bash-prompt-screen 27 else 28 PROMPT_COMMAND='echo -ne "\033_${USER}@${HOSTNAME%%.*}:${PWD/#$HOME/~}"; echo -ne "\033\\"' 29 fi 30 ;; I've disable bash-prompt-screen by renaming it--this fixed it. It's entirely possible that there is a fix to the bash-prompt-screen prompt line in the latest version of screen for RHEL 5. The error is seen under Screen version 4.00.03 (FAU) 23-Oct-06. (I noticed an update in the queue, which is installing as I write this.)

    Read the article

  • postfix says mail sent ok, message does not arrive in ISPs inbox? no reject in log?

    - by Nick
    When I send a test message from my mail server to my @bellsouth.net email, The postfix log shows it was sent OK, but the message never arrives in my bellsouth inbox. Shouldn't I get a failure notice or a bounce if At&T is blocking the messages? I'm trying to troubleshoot why some customers aren't getting emails, but if there's nothing in mail.log to say the message is rejected, how do I know which messages were delivered successfully? The log shows: Feb 27 09:02:36 MyHOSTNAME postfix/pickup[26175]: D53A72713E5: uid=0 from=<root> Feb 27 09:02:36 MyHOSTNAME postfix/cleanup[26487]: D53A72713E5: message-id=<[email protected]> Feb 27 09:02:36 MyHOSTNAME postfix/qmgr[5595]: D53A72713E5: from=<[email protected]>, size=878, nrcpt=1 (queue active) Feb 27 09:02:37 MyHOSTNAME postfix/smtp[26490]: D53A72713E5: to=<[email protected]>, relay=gateway-f1.isp.att.net[204.127.217.16]:25, delay=0.57, delays=0.11/0.03/0.23/0.19, dsn=2.0.0, status=sent (250 ok ; id=20120227140036M0700qer4ne) Feb 27 09:02:37 MyHOSTNAME postfix/qmgr[5595]: D53A72713E5: removed The AT&T server accepted the message, right? I happen to have an At&T/Bellsouth email, but I don't have an account with every ISP we send to. I need some way of knowing if a message is getting to its destination or not. Is there any setting in my main.cf file that would affect whether or not we get reject/bounce notices?

    Read the article

  • Trouble with IIS SMTP relaying to Gmail

    - by saille
    I appreciate that similar questions have been asked about how to setup SMTP relaying with IIS's virtual SMTP server. However I'm still completely stumped on this problem. Here's the setup: IIS 6.0 SMTP server running on Win2k3 box with a NAT'ed IP. Company uses Gmail for all email services. An app on the box needs to send email, so normally we'd just set the app up to talk to smtp.gmail.com directly, but this app doesn't support TLS. Easy, we just setup a local SMTP relay right? So I thought. What we have done so far: Setup IIS SMTP server to relay to smtp.gmail.com, as per these excellent instructions: http://fmuntean.wordpress.com/2008/10/26/how-to-configure-iis-smtp-server-to-forward-emails-using-a-gmail-account/ The local SMTP relay allows anonymous access. Both the local IP and the loopback IP have been explicitly allowed in the Connection and Relay dialogs. Tried sending email from 2 different apps via the local SMTP server, but failed (the emails end up in the Queue folder, but never get sent). The IIS logs show the conversation with the local app, but zero conversation happening with smtp.gmail.com. The port used by gmail is open outbound, and indeed the apps we have that support TLS can send email directly via smtp.gmail.com, so there is no problem with the network. At this point I changed the smtp settings in IIS SMTP server to use a different external SMTP server and hey-presto, the local apps can send email via local IIS SMTP relay. So smtp.gmail.com fails to work with our IIS SMTP relay, but another 3rd party SMTP service works fine. We need to use smtp.gmail.com, so how to troubleshoot this one?

    Read the article

  • Cisco QoS Guidance

    - by Kyle Brandt
    I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future. I do have VOIP at one location connected to this one over the Internet that goes through a VPN tunnel. Everything else that is between this location and other offices is on a separate MPLS network.

    Read the article

  • Postfix does not work after setting server hostname from plesk

    - by Michael
    I have recently set my server hostname from localhost.localdomain to xx.mydomain.com from the plesk control panel. However after doing this change postfix has stopped working, I tried restarting and regenerating the config files but to no avail. I am not familiar with postfix but I believe there is a setting to be changed in main.cf. Here are the relevant errors I receive: postfix/postfix-script: starting the Postfix mail system postfix/master: daemon started -- version 2.8.4, configuration /etc/postfix postfix/cleanup: fatal: host/service localhost/12768 not found: Name or service not known postfix/pickup: warning: maildrop/E5559996219: error writing 4FA2C996217: queue file write error postfix/master: warning: process /usr/libexec/postfix/cleanup pid 15334 exit status 1 postfix/master: warning: /usr/libexec/postfix/cleanup: bad command startup -- throttling Any ideas? EDIT Setting it back to localhost.localdomain makes it work again. The only references to localhost/12768 I can find in main.cf are: smtpd_milters = inet:localhost:12768 non_smtpd_milters = inet:localhost:12768 Should something be changed here? These two lines stay the same when I change the hostname. EDIT If I comment out the two mail filter lines (the ones shown above) and restart, postfix works with the new hostname. However this is obviously not the ideal solution...

    Read the article

  • Getting 502 instead of 503 when all backend servers are down running HAProxy behind Apache

    - by scarba05
    I'm testing running HAProxy as a dedicated load balancer behind Apache 2.2, replacing our current configuration where we use Apache's load balancer. In our current, Apache only, set-up if all the backend (origin) servers are down Apache will serve a 503 service unavailable message. With HAProxy I get a 502 bad gateway response. I'm using a simple reverse proxy rewrite rule in Apache RewriteRule ^/(.*) http://127.0.0.1:8000/$1 [last,proxy] In HAProxy I have the following (running in default tcp mode) defaults log global option tcp-smart-accept timeout connect 7s timeout client 60s timeout queue 120s timeout server 60s listen my_server 127.0.0.1:8000 balance leastconn server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 server backend1 127.0.0.1:8001 check observe layer4 maxconn 2 Testing connecting directly to the load balancer when the backend servers are down: [root@dev ~]# wget http://127.0.0.1:8000/ test.html --2012-05-28 11:45:28-- http://127.0.0.1:8000/ Connecting to 127.0.0.1:8000... connected. HTTP request sent, awaiting response... No data received. So presumably this is down to the fact that HAProxy accepts the connection and then closes it.

    Read the article

  • Postfix + procmail - delivery fails because "can't create user output file" - on CentOS 6.2

    - by jshin47
    I verified that my postfix installation / relaying setup worked. Now I am having trouble with procmail. I have it wired to postfix with the following command: mailbox_command = /usr/bin/procmail -f -a "$USER" I have nothing in my procmail config but the following: LOGFILE=/var/procmailrc/log And I send an email to a recipient that previously worked (before I attached procmail). Now it fails with error: Apr 6 14:07:05 localhost postfix/qmgr[15194]: D0C3DFF6E1: from=<[email protected]>, size=938, nrcpt=1 (queue active) Apr 6 14:07:05 localhost postfix/local[1953]: D0C3DFF6E1: to=<[email protected]>, orig_to=<postmaster>, relay=local, delay=0.05, delays=0.02/0.01/0/0.02, dsn=5.2.0, status=bounced (can't create user output file. Command output: procmail: Couldn't create "/var/spool/mail/nobody" procmail: Couldn't read "//root" ) Apr 6 14:07:05 localhost postfix/bounce[1955]: warning: D0C3DFF6E1: undeliverable postmaster notification discarded Apr 6 14:07:05 localhost postfix/qmgr[15194]: D0C3DFF6E1: removed It seems like there is some sort of permissions issue but I do not know what the problem is, nor do I understand how I would go about diagnosing it further. The logfile that I specified is empty, by the way. How can I make procmail+postfix work?

    Read the article

  • Procmail Postfix issue

    - by Blucreation
    Our server is using CENTOS uses postfix: Nov 1 11:31:52 webserver postfix/smtpd[30424]: 822A91872F: client=unknown[5.133.168.42], sasl_method=PLAIN, [email protected] Nov 1 11:31:52 webserver postfix/cleanup[30427]: 822A91872F: message-id=<[email protected]> Nov 1 11:31:52 webserver postfix/qmgr[1067]: 822A91872F: from=<[email protected]>, size=620, nrcpt=1 (queue active) Nov 1 11:31:52 webserver postfix/virtual[30505]: 822A91872F: to=<[email protected]>, relay=virtual, delay=0.12, delays=0.12/0/0/0, dsn=2.0.0, status=sent (delivered to maildir) Nov 1 11:31:52 webserver postfix/qmgr[1067]: 822A91872F: removed Nov 1 11:31:52 webserver postfix/smtpd[30424]: disconnect from unknown[5.133.168.42] I have this in my etc/postfix/main.cf: mailbox_command = /usr/bin/procmail -a "$EXTENSION" My etc/procmailrc contains: PATH="/usr/bin" SHELL="/bin/bash" LOGFILE="/var/log/procmail.log" VERBOSE="YES" LOG="#TEST#" I don't think procmail is picking up on my procmailrc as nothing ever gets logged from normal emails. If i type this: procmail DEFAULT=/dev/null VERBOSE=yes LOGFILE=/var/log/procmail.log /dev/null </dev/null I get entries in my log file so i know procmail is working Am i doing something wrong? am i missing something? I eventually want my rule to call a php script only if the subject contains "SUPPORT TICKET" and the to is "[email protected]" but that's once i this issue solved.

    Read the article

  • CUPS causes printer to click and doesn't print

    - by Pez Cuckow
    I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

    Read the article

  • Exchange 2010 Hub cannot deliver to Exchange 2007 Hub - "451 5.7.3 Cannot achieve Exchange Server authentication"

    - by Graeme Donaldson
    We have an existing Exchange 2007 server in Site A (exch07). I've installed an Exchange 2010 server in Site B (exch10). Both servers have the CAS, Mailbox and Hub roles. Messages sent via SMTP on exch10 which are destined for mailboxes on exch07 are queued with the "Last Error" reported in Queue Viewer as '451 4.4.0 Primary target IP address responded with: "451 5.7.3 Cannot achieve Exchange Server authentication." Attempted failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts.' I've found that some people have resolved this by creating new Receive Connectors which are scoped specifically to apply to connections from the remote hub/s, but I have had no luck doing this. Specifically I created new receive connectors on both servers with the following settings: Remote IP = IP/s of remote server Authentication = "Transport Layer Security (TLS)" and "Exchange Server authentication" Permission Groups = "Exchange servers" and "Legacy Exchange Servers" This made no difference, I see the same error message. What am I missing? Update: We noticed that the Application log had this error message from MSExchangeTransportService: Microsoft Exchange could not find a certificate that contains the domain name exch07.domain.local in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector exch10 with a FQDN parameter of exch07.domain.local. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. It turns out that the default self-signed certificate was no longer enabled for the SMTP service for some reason. After enabling the self-signed certificate for SMTP, we no longer get the error in the event logs, but delivery is still failing with the same error message. Update 2: I put a mailbox on exch10 and attempted to deliver a message via SMTP on exch07 and I get the same error.

    Read the article

  • Server nearly unusable when doing disk writes

    - by Wikser
    My question closely relates to my last question here on serverfault. I was copying about 5GB from a 10 year old desktop computer to the server. The copy was done in Windows Explorer. In this situation I would assume the server to be bored by the dataflow. But as usual with this server, it really slowed down. At least I could work with the remote session, even there was some serious latency. The copy took its time (20min?). In this time I went to a colleague and he tried to log in in the same server via remote desktop (for some other reason). It took about a minute to get to the login screen, a minute to open the control panel, a minute to open the performance monitor, ... Icons were loading maybe one per second. We saw the following (from memory): CPU: 2% Avg. Queue Length: 50 Pages/sec: 115 (?) There was no other considerable activity on the server. The server seldom serves some ASP.NET pages, which became also very slow in this time. The relevant configuration is as follows: Windows 2003 SEAGATE ST3500631NS (7200 rpm, 500 GB) LSI MegaRAID based RAID 5 4 disks, 1 hot spare Write Through No read-ahead Direct Cache Mode Harddisk-Cache-Mode: off Is this normal behaviour for such a configuration? What measurements could give further clues? Is it reasonable to reduce the priority of such copy I/O and favour other processes like the remote desktop? How would you do that? Many thanks!

    Read the article

  • Cron won't use msmtp to send emails in case of failed cronjob

    - by Glister
    I'm trying to configure a machine so that it will send me an email if one of the cronjobs output something in case of an error. I'm using Debian Wheezy. Cron is working normally (without the email functionality). msmtp is installed and configured. Have already symlinked /usr/{bin|sbin}/sendmail to /usr/bin/msmtp. I can send email by using: echo "test" | mail -s "subject" [email protected] or by executing: echo "test" | /usr/sbin/sendmail Without the symlink (/usr/sbin/sendmail) cron will tell me that: (CRON) info (No MTA installed, discarding output) With the symlinks I get: (root) MAIL (mailed 1 byte of output; but got status 0x004e, #012) Can you suggest how to config the cron/msmtp pair? Thanks! EDIT: Note: I've written "msmtpd" by mistake. Its not a daemon but rather an SMTP client named just "msmtp" (without the "d" ending). It is executed on demand and it is not running in the background all the time. When I try to send an email by using msmtp like that it works: echo "test" | msmtp [email protected] On the far side, in the logs of the SMTP server I read: Nov 2 09:26:10 S01 postfix/smtpd[12728]: connect from unknown[CLIENT_IP] Nov 2 09:26:12 S01 postfix/smtpd[12728]: 532301C318: client=unknown[CLIENT_IP], sasl_method=CRAM-MD5, [email protected] Nov 2 09:26:12 S01 postfix/cleanup[12733]: 532301C318: message-id=<> Nov 2 09:26:12 S01 postfix/qmgr[2404]: 532301C318: from=<[email protected]>, size=191, nrcpt=1 (queue active) Nov 2 09:26:12 S01 postfix/local[12734]: 532301C318: to=<[email protected]>, orig_to=<[email protected]>, relay=local, delay=0.62, delays=0.59/0.01/0/0.03, dsn=2.0.0, status=sent (delivered to command: IFS=' ' && exec /usr/bin/procmail -f- || exit 75 #1001) Nov 2 09:26:12 S01 postfix/qmgr[2404]: 532301C318: removed Nov 2 09:26:13 S01 postfix/smtpd[12728]: disconnect from unknown[CLIENT_IP] And the Email is delivered to the target user. So it looks like that the msmtp client is working properly. It has to be something in the cron/msmtp integration, but I have no clue what that thing might be. Can you help me?

    Read the article

  • HAproxy with MySQL Master-Master Replication incredibly slow

    - by Yayap
    I have two MySQL servers in multi-master mode, with an HAproxy machine for simple load balancing/redundancy. When I am connected to one of the servers directly and try to update about 100,000 entries, it is completed including replication in about half a minute. When connecting through the proxy it takes usually over three whole minutes. Is it normal to have that type of latency? Is something amiss with my proxy configuration (included below)? This is getting really frustrating as I assumed the proxy would do some sort of load balancing, or at least have little to no overhead. #--------------------------------------------------------------------- # Example configuration for a possible web application. See the # full configuration options online. # # http://haproxy.1wt.eu/download/1.4/doc/configuration.txt # #--------------------------------------------------------------------- #--------------------------------------------------------------------- # Global settings #--------------------------------------------------------------------- global # to have these messages end up in /var/log/haproxy.log you will # need to: # # 1) configure syslog to accept network log events. This is done # by adding the '-r' option to the SYSLOGD_OPTIONS in # /etc/sysconfig/syslog # # 2) configure local2 events to go to the /var/log/haproxy.log # file. A line like the following can be added to # /etc/sysconfig/syslog # # local2.* /var/log/haproxy.log # log 127.0.0.1 local2 # chroot /var/lib/haproxy # pidfile /var/run/haproxy.pid maxconn 4096 user haproxy group haproxy daemon #debug #quiet # turn on stats unix socket stats socket /var/lib/haproxy/stats #--------------------------------------------------------------------- # common defaults that all the 'listen' and 'backend' sections will # use if not designated in their block #--------------------------------------------------------------------- defaults mode tcp log global #option tcplog option dontlognull option tcp-smart-accept option tcp-smart-connect #option http-server-close #option forwardfor except 127.0.0.0/8 #option redispatch retries 3 #timeout http-request 10s #timeout queue 1m timeout connect 400 timeout client 500 timeout server 300 #timeout http-keep-alive 10s #timeout check 10s maxconn 2000 listen mysql-cluster 0.0.0.0:3306 mode tcp balance roundrobin option tcpka option httpchk server db01 192.168.15.118:3306 weight 1 inter 1s rise 1 fall 1 server db02 192.168.15.119:3306 weight 1 inter 1s rise 1 fall 1

    Read the article

  • Resolving "not found" messages after doing ./configure building node.js

    - by duke
    Hello I am trying to install node.js on debian AMD64. I got node.js from git. When I do ./configure a bunch of "checking for program" messages say "not found". I want to resolve all these and ensure everything needed is present. Can anyone suggest what I need to do to resolve the "not found" messages? Thanks heaps. server:/devel/node# ./configure Checking for program g++ or c++ : /usr/bin/g++ Checking for program cpp : /usr/bin/cpp Checking for program ar : /usr/bin/ar Checking for program ranlib : /usr/bin/ranlib Checking for g++ : ok Checking for program gcc or cc : /usr/bin/gcc Checking for gcc : ok Checking for library dl : yes Checking for library execinfo : not found Checking for openssl : not found Checking for function SSL_library_init : yes Checking for header openssl/crypto.h : yes Checking for library rt : yes --- libeio --- Checking for library pthread : yes Checking for function pthread_create : yes Checking for function pthread_atfork : yes Checking for futimes(2) : yes Checking for readahead(2) : yes Checking for fdatasync(2) : yes Checking for pread(2) and pwrite(2) : yes Checking for sendfile(2) : yes Checking for sync_file_range(2) : yes --- libev --- Checking for header sys/inotify.h : yes Checking for function inotify_init : yes Checking for header sys/epoll.h : yes Checking for function epoll_ctl : yes Checking for header port.h : not found Checking for header poll.h : yes Checking for function poll : yes Checking for header sys/event.h : not found Checking for header sys/queue.h : yes Checking for function kqueue : not found Checking for header sys/select.h : yes Checking for function select : yes Checking for header sys/eventfd.h : not found Checking for SYS_clock_gettime : yes Checking for library rt : yes Checking for function clock_gettime : yes Checking for function nanosleep : yes Checking for function ceil : yes Checking for fdatasync(2) with c++ : yes 'configure' finished successfully (1.479s) server:/devel/node#

    Read the article

  • Dovecot unable to perform mysql query

    - by NathanJ2012
    I have been following the ISPMail tutorials on workaround.org (the 2.9 Wheezy version) and thus far everything has been working fine. When I reached the step to "Testing email delivery" step I noticed a error about the query in the output log from /var/log/mail.log. May 14 06:48:59 mail postfix/pickup[17704]: EA4AD240A98: uid=0 from=<root> May 14 06:48:59 mail postfix/cleanup[17776]: EA4AD240A98: message-id=<[email protected]> May 14 06:48:59 mail postfix/qmgr[17706]: EA4AD240A98: from=<[email protected]>, size=429, nrcpt=1 (queue active) May 14 06:49:00 mail dovecot: auth-worker(17782): mysql(127.0.0.1): Connected to database mailserver May 14 06:49:00 mail dovecot: auth-worker(17782): Warning: mysql: Query failed, retrying: Table 'mailserver.users' doesn't exist May 14 06:49:00 mail dovecot: auth-worker(17782): Error: sql([email protected]): User query failed: Table 'mailserver.users' doesn't exist (using built-in default user_query: SELECT home, uid, gid FROM users WHERE username = '%n' AND domain = '%d') May 14 06:49:00 mail dovecot: lda([email protected]): msgid=<[email protected]>: saved mail to INBOX May 14 06:49:00 mail postfix/pipe[17780]: EA4AD240A98: to=<[email protected]>, relay=dovecot, delay=0.09, delays=0.03/0.01/0/0.06, dsn=2.0.0, status=sent (delivered via dovecot service) May 14 06:49:00 mail postfix/qmgr[17706]: EA4AD240A98: removed I found this rather interesting that it isn't finding the DB so I went back through and checked EVERY file that I touched that involved the DB (including the postfix cf files) and everything is correct so I am baffled at this point, but oddly enough it would seem the email still made it to the correct destination in /var/vmail/domain.com/. Should I be worried about this or am I missing something here? Since it is a message from dovecot it would be the query from dovecot-sql.conf.ext which I am including here driver = mysql connect = host=127.0.0.1 dbname=mailserver user=blocked password=***REMOVED*** default_pass_scheme = PLAIN-MD5 password_query = SELECT email as user, password FROM virtual_users WHERE email='%u';

    Read the article

  • MySQL Server hitting 100% unexpectedly (Amazon AWS RDS)

    - by Luc
    Please help! We've been struggling with this one for months. This week we upped our RDS instance to the highest performing instance and although the occurrences have reduced, we're still having our DB all of a sudden hit 100%. It comes out of nowhere. Sometimes 2am, sometimes midday. I've ruled out a DOS - our pages access logs have normal traffic I've ruled out memcached suddenly dieing (hits and misses continue as normal). The SHOW PROCESSLIST while we have issues reports about 500 queries in queue. If I kill them off or restart the server, they just keep coming back and then eventually out of knowhere, our server resumes back to normal. Sometimes up to 3 hours. Our bad performing queries take .02 seconds to execute when the server eventually returns back to normal but while we're in this 100% CPU physco phase, those queries never finish executing. Please help!!!!! Anybody know anything about MYSQL query optimization? Could it be the server deciding to use different indexes all of a sudden, which puts it into a spiral?

    Read the article

  • Why does Windows make random "device connect" and "device disconnect" sounds?

    - by Steve Elmer
    Hello, I've been noticing this since Windows Vista. I see it on Windows 7, now, as well. In any case throughout the day I notice that my computer makes apparently random device-connect and/or device-disconnect ("boink") sounds. I suppose it is the same sound you hear when connecting or disconnecting a USB device such as a thumb drive. I've noticed that this happens on each of three computers I work with at home, my wife's computer, and my machine at work. It happens without any user action at all - i.e. I'll be just sitting there (hands off my mouse and keyboard), and the computer will make the sound. There is no visual queue or anything. Just the sound. I have sometimes gone in pursuit of the sound - running virus scans, examining event logs and such, and observing task manager - but have never had any luck tracking this thing down, but have not had any luck. Surely someone else out there must be experiencing this, too. Any ideas? Thanks, Steve

    Read the article

< Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >