Search Results

Search found 3444 results on 138 pages for 'o r mapping'.

Page 106/138 | < Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

• Windows Server Hyper-V guests cannot see each other on network

  - by Noldorin

  I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

  Read the article

• Scheduled task does not run on WIndows 2003 server on VMWare unattened, runs fine otherwise

  - by lnm

  Scheduled task does not run on Windows 2003 server on VMWare. The same setup runs fine on standalone server. Test below explains the problem. We really need to run a more complex bat file, but this shows the issue. I have a bat file that copies a file from server A to server B. I use full path name, no drive mapping. Runs fine on server B from command prompt. I created a task that runs this bat file under a domain id with password that is part of administrator group on both servers. Task runs fine from Scheduled task screen, and as a scheduled task as long as somebody is logged into the server. If nobody is logged in, the task does not run. There is no error message in Task Scheduler log, just an entry that the task started, bit no entry for finish or an error code. To add insult to injury, if the task copies a file in the opposite direction, from server B to server A, it runs fine as a scheduled unattended task. If I copy a file from server B to server B, the task also runs fine unattended, I recreated exactly the same setup on a standalone server. No issues at all. I checked obvious things like the task has "run only as logged in" unchecked, domain id has run as a batch job privilege and logon rights, Task Scheduler service runs as a local system, automatic start. Any suggestions?

  Read the article

• Installing OEM Windows Server 2008 under KVM

  - by rancidfishbreath

  Issue I have an HP server that came with an OEM copy of Windows Server 2008. I have installed CentOS 5.4 on the hardware and am trying to install Windows Server 2008 as a KVM guest. When I attempt to install Windows Server 2008 it complains that I am trying to install on unsupported hardware. This issue is caused because the hardware SMBIOS information is not being passed to the KVM guest. Background Before I go any further I want to state that what I am trying to do is within the license. HP offers a supported solution for VMWare but does not have an official solution for KVM. After much research the platform I am going to use is CentOS and KVM so please do not suggest other platforms. I emailed the KVM developers mailing list and was told that this is possible and was given the advice that: "You can dump SLIC table of your host bios and provide it to guest bios using -acpitable parameter." I used dmidecode and got the parameters that need to be passed, but I do not know where to pass the parameters into. Update Looks like CentOS 5.4 uses virt-install instead of qemu. Qemu is in the package manager and I was able to install it after uninstalling qemu-img (they conflict and qemu contains the packages in qemu-img). So now I know how to pass the acpitable parameters, but I am having trouble mapping what came out of dmidecode into -acpitable.

  Read the article

• Configuring vlans on Cisco SG200 series switch with Ubuntu server

  - by nixnotwin

  I created a vlan on Ubuntu with vconfig tool with 21 as id and eth1 as the host port. I connected eth1 to one of the ports on the swtich (GE23) as all ports trunk by default. In the webgui I created a vlan named test with the id 21 and I made GE2 are port as an access port. In port to vlan mapping I selected vlan 21 and added it port GE2 by selecting untagged option. I have assigned 192.168.1.1/24 as the ip of eth1.21 on Ubuntu. If I connect another cleint pc to GE2 port with a ip of 192.168.1.2/24 I cannot ping the server ip (192.168.1.1/24). Ping from server to client also does not work. I inspected packets that are sent out eth1 on the server and I could see the vlan 21 tag. And I connect the other end of the cable to a different Linux pc and inspected the packets but no vlan tags can be seen. What could be preventing me from getting vlans working? Edit 1 screenshots:

  Read the article

• Email test deferred (mail transport unavailable) with ClamAV

  - by dirt

  I'm trying to set up a simple new mail server; when I send a test email to the server the email is getting hung up during delivery (user mapping is found) and the email is never found in /home/user/Maildir/new Here is my maillog after a fresh reboot and test email, there are a few warnings I am unfamiliar with. Can you please point me in the right direction? Oct 25 14:54:57 loki dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Oct 25 14:54:58 loki postfix/postfix-script[1369]: starting the Postfix mail system Oct 25 14:54:58 loki postfix/master[1370]: daemon started -- version 2.6.6, configuration /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: request to update table btree:/etc/postfix/smtpd_scache in non-postfix directory /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: redirecting the request to postfix-owned data_directory /var/lib/postfix Oct 25 14:56:00 loki postfix/smtpd[1455]: connect from mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/smtpd[1455]: 1CF5E20A8B: client=mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/cleanup[1461]: 1CF5E20A8B: message-id= Oct 25 14:56:01 loki postfix/qmgr[1379]: 1CF5E20A8B: from=, size=1788, nrcpt=1 (queue active) Oct 25 14:56:01 loki postfix/qmgr[1379]: warning: connect to transport private/scan: No such file or directory Oct 25 14:56:01 loki postfix/error[1462]: 1CF5E20A8B: to=, orig_to=, relay=none, delay=0.18, delays=0.15/0.02/0/0.01, dsn=4.3.0, status=deferred (mail transport unavailable) Oct 25 14:56:01 loki postfix/smtpd[1455]: disconnect from mail-ob0-f180.google.com[209.85.214.180] master.cf snippets: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING scan unix - - n - 16 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes 127.0.0.1:10026 inet n - n - 16 smtpd -o content_filter= -o local_recipient_maps= -o relay_recipient_maps= -o smtpd_restriction_classes= -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks_style=host -o smtpd_authorized_xforward_hosts=127.0.0.0/8

  Read the article

• Network share not always available on Windows 2003

  - by JP Hellemons

  Hello everybody, we have a windows 2003 server with a shared directory/folder. I've seen this thread but this wasn't any help: http://superuser.com/questions/58890/the-specified-network-name-is-no-longer-available I have a ping -t running from 3 pc's (vista and two windows 7) they all work. the problem occurss when two users enter the network share then this 'network share is no longer available' appears and the explorer windows turn white. after f5 or refresh the shared directory is back. this is really strange. there is no anti virus or kasparsky running on either end. this is all in the same LAN. the internet connection is really stable, so it's really strange. because a stable internet connection should imply that the local network connection is also stable and that this is a windows issue. can it be a router issue? I have checked the eventlog on the server for diskfailure related messages, but there are none. EDIT: can this be related to mapping a shared directory to a drive letter? and that there is a router between me and the mapped network drive? or is it just windows that is not working well with two users on the same shared folder? should I install samba or something?

  Read the article

• Networking DOS within Windows 7 XP Mode, with a Windows XP/7 Networked Share

  - by theonlylos

  For awhile now, one of my clients has been stuck with Corel Paradox 4.0 (it used to be the biggest database system in the DOS days, until Microsoft released Access in the early 90's) so for awhile I've managed to keep it on life support on Windows XP for a few years, however since switching to Windows 7 x64, I've had to resort to using XP Mode as the sandbox to keep it up and running. While I am able to run Paradox as usual in XP Mode, I'm having a serious issue where if I try connecting the install to the network share (which is located on the Windows 7 portion of the system), Paradox keeps exiting because it says the serial number is invalid. Now, I know for a fact that this is an issue with the virtual loopback adapter and also having the VM linked to the physical ethernet adapter -- and while I have solved this issue before, most of my fixes have been bandages since after a few weeks the issue pops up again. Long story short, I wanted to ask if there is a permanent way to link a DOS program to a network share address. For example, when I try doing \tsclient\paradox (the Windows 7 Address) I keep getting an error saying I need a valid network address. I've tried mapping that folder to various drive letters such as P:\Paradox -- but for some reason that keeps failing over time. For what it's worth, Paradox uses a .SOM file to store the network settings, however it isn't editable in Notepad but rather it's controlled by a wizard in Paradox. But if that extension rings any bells, I'd welcome any insights.

  Read the article

• QNAP NAS 509 (LINUX) - how to unmout busy volume and find physical disk?

  - by Horst Walter

  On my NAS QNAP TS 509 I do have a technical issue. I need to run e2fsck. This works fine for me on md0 (see below), but how can I unmount the busy devices md9 and sda4 in order to do the same. Whenever I try, I fail because the device is busy. [This part is solved, see below] In order to further track down the issue, I'd need to sort out the physical disk to device relationship. How can I find out this, e.g. md0 is a stripped volume on 2 disk (but I need to find out on what physical disk). Remark: As you can easily derive from my questions, I am not a Linux expert, but manage to get along. /dev/ram0 124.0M 94.1M 29.8M 76% / tmpfs 32.0M 80.0k 31.9M 0% /tmp /dev/sda4 310.0M 103.9M 206.1M 34% /mnt/ext /dev/md9 509.5M 39.2M 470.2M 8% /mnt/HDA_ROOT /dev/md0 1.8T 1.4T 444.7G 76% /share/MD0_DATA tmpfs 32.0M 0 32.0M 0% /.eaccelerator.tmp -- Added -- QNAP seems to be based on Busybox. I do not find something like init / telinit / runlevel. At busybox docs it says that I need to run the below. But in /var/service sv is not available. I want to go to single user mode to unmount the devices. # cd /var/service # sv d * # sv u getty* -- Added, thanks A4L -- This QNAP Box runs a special flavor of Linux, so not all SOPs do apply. In my particular case I found a services.sh script, stopping all services. After that the drive could be unmounted. The information passed by A4L is valid and worth reading it, maybe I'll profit from it next time. Links: http://unix.stackexchange.com/questions/19918/umount-device-is-busy and http://unix.stackexchange.com/questions/15024/umount-device-is-busy-why So the unmount issue is solved, still looking for the best option to find the physical to volume mapping.

  Read the article

• How to extract a Vorbis stream from a WAVE file?

  - by H.B.

  I would like to move the Vorbis stream into an ogg container but ffmpeg does not seem to recognize the stream. Even though MPlayer gives this output upon playback: Opening audio decoder: [acm] Win32/ACM decoders Loading codec DLL: 'vorbis.acm' Loaded DLL driver vorbis.acm at 10000000 Warning! ACM codec reports srcsize=0 AUDIO: 44100 Hz, 2 ch, s16le, 128.0 kbit/9.07% (ratio: 16000-176400) Selected audio codec: [vorbisacm] afm: acm (OggVorbis ACM) ffmpeg: ffmpeg -i Source.wav -acodec copy Target.ogg Input #0, wav, from 'Source.wav': Duration: 00:02:15.17, bitrate: 128 kb/s Stream #0.0: Audio: qg[0][0] / 0x6771, 44100 Hz, 2 channels, 128 kb/s [ogg @ 00000000003096C0] Unsupported codec id in stream 0 Output #0, ogg, to 'Target.ogg': Metadata: encoder : Lavf53.6.0 Stream #0.0: Audio: qg[0][0] / 0x6771, 44100 Hz, 2 channels, 128 kb/s Stream mapping: Stream #0.0 -> #0.0 Could not write header for output file #0 (incorrect codec parameters ?) Of course this does not necessarily need to be done via ffmpeg, any method that is workable would be fine... I have cut down one of the files to 512KB: sample.wav (Changed two chunk size fields in the wave header to account for this, the embedded stream is cut "without notice")

  Read the article

• postfix (for sending mail only) multiple domain setup

  - by seanl

  I have the following problem, I have a Centos 5.4 VPS hosting a few nginx sites (some static, some cakephp), I would like to be able to send email from each sites contact page through postfix to my google apps hosted email (different accounts for each site) so that apps can then send out an auto email to the person filling in the contact form etc I have a bare-bones postfix installation with the following added into the main.cf config file. from using this guide virtual_alias_domains = hash:/etc/postfix/virtual_alias_domains virtual_alias_maps = hash:/etc/postfix/virtual_alias_maps (both of these files have been converted into db files using postmap) I have configured DNS correctly for each site and setup SPF records. (I'm aware R-DNS will still reference my actual hostname not the domain name and cause a possible spam issue but one thing at a time) I can telnet localhost and the helo localhost so that I can send a command line email from an address in the virtual_alias_domains to an email in the virtual_alias_maps file which seems sends without giving an error but it is sending to my local linux account not the email address specified. my question is am i approching this the wrong way in terms of the virtual alias mapping or is this even possible to do in the manner im trying. Any help is greatly appreciated thanks. my postconf -n outlook looks like this alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost myhostname = myactual hostname mynetworks = 127.0.0.0/8 myorigin = $mydomain newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES sample_directory = /usr/share/doc/postfix-2.3.3/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop unknown_local_recipient_reject_code = 550 virtual_alias_domains = hash:/etc/postfix/virtual_alias_domains virtual_alias_maps = hash:/etc/postfix/virtual_alias_maps

  Read the article

• IIS doesn't serve certain file extensions

  - by Alekc

  Hi, i have this weird issue on Win 2k3 server and IIS: Iis has several sites, in one of them i need to create a subdir and set up it as web application. I've noticed that if i create new directory and put some .js/.txt file into it, they will not be served by iis (IE gives an error Internet Explorer cannot display the webpage). If i put the same files in another old site's subdirectory it will show correctly. By sniffing traffic i've seen that iis reply connection state 200 and then drop completely any connection http://domain.com/test2/prova.txt GET /test2/prova.txt HTTP/1.1 Host: domain.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.1.7) Gecko/20091221 Firefox/3.5.7 (.NET CLR 3.5.30729) Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive HTTP/1.x 200 OK If i rename file prova.txt in prova.asp for example it showing without problems so it shouldn't be permissions issue. After making some researches I've found out that it can be caused by missing mime types, I've checked out .txt and .js are present and served by aspnet_isapi.dll. And here comes another weird thing: if i remove mime mapping from directory's properties it's served correctly, but the same thing doesn't work with js. I'm really beginning to be out of ideas, is there someone who have some hint? Thanks in advance.

  Read the article

• No LPT port in Windows 7 virtual machines

  - by KeyboardMonkey

  Windows 7 has MS virtual PC integrated, the VM settings don't give a parallel LPT port mapping to the physical machine. Where did it go? Has anyone else noticed this, and found a solution? Update: After much digging, I found the one and only reference to this issue, on the VPC Blog: "Parallel port devices are not supported, as they are relatively rare today." -More details- It's a XP VM I've been using since VPC 2007 days, which did have this functionality. This is to configure barcode printers via the LPT port. Since the (new) MS VM can't map to my physical LPT port, I'm having a hard time configuring printers. My physical ports are enabled in the BIOS. It has worked the past 3 years, before switching to Win 7. Any help is appreciated. This screen shot of the VM settings shows COM ports, but LPT is no more In contrast, here is a screen shot of VPC 2007 (before it got integrated into Win 7). Notice how it has LPT support

  Read the article

• FFMPEG: how to add watermark to video?

  - by DocWiki

  My Platform: Ubuntu 10.10 + FFMPEG 0.5.3(I installed ffmpeg from source) I try to add Watermark to a .MOV video with FFMPEG 0.5.3 imlib2.so (Please note FFMPEG 0.6+ dont support imlib2.so, so I use ffmpeg 0.5.3) Here is my code: ffmpeg -sameq -i example.mov -vhook '/usr/local/lib/vhook/imlib2.so -x 0 -y 0 -i /var/www/files/watermark.png' newexample.mov Here is the output: FFmpeg version 0.5.3, Copyright (c) 2000-2009 Fabrice Bellard, et al. configuration: --enable-avfilter --enable-filter=movie --enable-avfilter-lavf libavutil 49.15. 0 / 49.15. 0 libavcodec 52.20. 1 / 52.20. 1 libavformat 52.31. 0 / 52.31. 0 libavdevice 52. 1. 0 / 52. 1. 0 libavfilter 0. 4. 0 / 0. 4. 0 built on Jul 3 2011 12:05:08, gcc: 4.4.5 Seems stream 1 codec frame rate differs from container frame rate: 59.94 (5994/100) - 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'example.mov': Duration: 00:03:14.06, start: 0.000000, bitrate: 3350 kb/s Stream #0.0(eng): Audio: aac, 48000 Hz, stereo, s16 Stream #0.1(eng): Video: h264, yuv420p, 1150x647, 29.97 tbr, 29.97 tbn, 59.94 tbc Output #0, mov, to 'newexample.mov': Stream #0.0(eng): Video: mpeg4, yuv420p, 1150x647, q=2-31, 200 kb/s, 90k tbn, 29.97 tbc Stream #0.1(eng): Audio: 0x0000, 48000 Hz, stereo, s16, 64 kb/s Stream mapping: Stream #0.1 - #0.0 Stream #0.0 - #0.1 Unsupported codec for output stream #0.1 What could be the possible problem? Is that AAC or H264 that is not supported? I installed libavcodec-extra-52, linfaac, libfaad and etc. but the error is the same. Do I have to install following this instruction? HOWTO: Install and use the latest FFmpeg and x264 or there is a simpler solution?

  Read the article

• GA 8KNXP Rev1.0: 4 GB installed, only 3.5 GB recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4 GB. The specification from the manual says: Maximum memory support: 4 GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my Linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in Linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Xen domU passwd file overwritten with console log output

  - by malfy

  I was setting up a Debian Xen domU and after booting it fine, I added basic configuration to /etc/network/interfaces and ran /etc/init.d/networking restart. This failed so I decided to reboot. After the reboot I also ran xm shutdown box. When dropped to a shell prompt it wouldn't let me login. Upon further inspection, I now have garbage in some critical files in /etc: root@box:/# tail +1 mnt/etc/{passwd-,shadow} tail: cannot open `+1' for reading: No such file or directory ==> mnt/etc/passwd- <== 0000000000100000 (reserved) Nov 23 02:02:39 box kernel: [ 0.000000] Xen: 0000000000100000 - 0000000004000000 (usable) Nov 23 02:02:39 box kernel: [ 0.000000] DMI not present or invalid. Nov 23 02:02:39 box kernel: [ 0.000000] last_pfn = 0x4000 max_arch_pfn = 0x1000000 Nov 23 02:02:39 box kernel: [ 0.000000] initial memory mapped : 0 - 033ff000 Nov 23 02:02:39 box kernel: [ 0.000000] init_memory_mapping: 0000000000000000-0000000004000000 Nov 23 02:02:39 box kernel: [ 0.000000] NX (Execute Disable) protection: active Nov 23 02:02:39 box kernel: [ 0.000000] 0000000000 - 0004000000 page 4k Nov 23 02:02:39 box kernel: [ 0.000000] kernel direct mapping tables up to 4000000 @ 7000-2c000 Nov 23 02:02:3 ==> mnt/etc/shadow <== 32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1 Nov 23 02:02:39 box kernel: [ 0.000000] PERCPU: Embedded 15 pages/cpu @c15b0000 s37688 r0 d23752 u65536 Nov 23 02:02:39 box kernel: [ 0.000000] pcpu-alloc: s37688 r0 d23752 u65536 alloc=16*4096 Nov 23 02:02:39 box kernel: [ 0.000000] pcpu-alloc: [0] 0 Nov 23 02:02:39 box kernel: [ 0.000000] Xen: using vcpu_info placement Nov 23 02:02:39 box kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16160 Nov 23 02:02:39 box kernel: [ 0.000000] Kernel command line: root=/dev/mapper/xen-guest_root ro quiet root=/dev/xvda1 ro Nov 23 02:02:39 box kernel: [ 0.000000] PID hash table entries: The garbage is also present in the passwd file and the group file (although I didn't paste that above since I have since ran debootstrap on the filesystem again). Does anyone have any insight into what happened and why?

  Read the article

• Group policy not applying to security group

  - by ihavenoideawhatimdoing

  Preface: I have enough privileges to create GPOs in my OU, and have made a few of them for some simple tasks (like deploying a printer to certain users). Not actually a sysadmin...I'm a developer who is winging it. I wanted to create a GPO that would set a mapped folder for a certain security group (which I recently created and that contains only myself). Did the following: Created the GPO in MyOU - Users Removed the default Authenticted Users under Security Filtering Add the security group with my account to Security Filtering Set up the mapping via the User Configuration option Changed GPO Status to "Computer configuration settings disabled" Left WMI filtering to Closed the GPO at this point... Logged in as the target user; ran gpupdate /force Logged out, logged in, ran gpresult /r, no mention of my GPO Rebooted Logged in, re-ran gpupdate /force Logged out, logged in, ran gpresult /r, still no mention of my GPO If I log in with another completely different user, their RSOP information shows that the new GPO is being ignored due to a security restriction, so it appears to be "working" for other users. I just can't get it to actually show up in RSOP for the user it should be working. Is there anything else I can do short of rebooting endlessly and crossing my fingers?

  Read the article

• Postfix: How do I Make Email Aliases Work?

  - by Nick

  The documentation claims that I can add aliases in a file (like /etc/postfix/virtusertable) and then use the "virtual_maps" directive to point to it. This does not appear to be working, however. My mail is bouncing with: Recipient address rejected: User unknown in local recipient table; If I mail the user from the server using the mail command, it works. mail myuser The message goes through postfix and inserts itself in the Cyrus inbox correctly. When I use fetchmail to get the user's messages off a pop3 server, postfix fails. The user's email is "[email protected]", but it doesn't seem to be mapping correctly to "myuser", the cyrus mailbox name. /etc/postfix/main.cf myhostname = localhost alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all mailbox_transport = lmtp:unix:/var/run/cyrus/socket/lmtp #lmtp:unix:/var/run/lmtp virtual_alias_domains = mydomain.com virtual_maps = hash:/etc/postfix/virtusertable /etc/fetchmailrc et syslog; set daemon 20; poll "mail.pop3server.com" with protocol pop3 user "[email protected]" password "12345" is "myuser" fetchall keep /etc/postfix/virtusertable [email protected] myuser postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_size_limit = 0 mailbox_transport = lmtp:unix:/var/run/cyrus/socket/lmtp mydestination = localhost myhostname = localhost mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes virtual_alias_domains = mydomain.com Why is it ignoring my alias?

  Read the article

• Cannot find network path for computer in workgroup of home Windows XP PCs

  - by John Galt

  VMWare Workstation 6.5 is running as an app on a Windows Vista 64bit PC host. Thanks to Workstation we have 2 guest machines running: TerriVM and MattVM (both of these run Windows XP SP2). We are attempting to get virtual networking configured so we can access the files of both of these VM guest systems from other real PCs connected to this home network. We think we are close but we can't quite get it right... Here is what we've done so far: * On VM Workstation, we set "Host Virtual Network Mapping" to use VMnet0 with the setting "Bridge to an automatically chosen adapter". * On each VM guest (i.e. using Windows explorer on XP), we rightmouse on the C disk, click "Sharing" tab, set shareName to "C_Disk" and check both boxes labeled "Share this folder on the network" and "Allow network users to change my files". Symptoms: On "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \TerriVM\C_Disk and assign drive letter T. We see all the folders on this shared drive and can open files on them. So that is good. On same "JohnsRealXP" PC, we go to Windows Explorer, My Computer, Map Network Drive, type into Folder textbox: \MattVM\C_Disk and assign drive letter M. We get a message box "_The network path \mattvm\C_Disk could not be found_". Alternatively, we type just \mattvm\ into the Folder box and click "Browse" and get a dialog box where we drill down from "Entire Network" to "Microsoft Windows Network" to "Workgroup" where both TerriVM and MattVM are listed as computers on the network. Clicking the + sign next to MattVM gives an hourglass and never enables the OK button and I have to cancel. In summary, I think we've attempted to share both of these virtual machines using the same techniques and connect to them in similar fashion, but one connects properly and the other machine can be seen but no shared resources on it can be accessed. Can anyone suggest something possibly overlooked or something to try? Thanks so much in advance.

  Read the article

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Vlans and subinterfaces

  - by Adeodatus

  I've inherited a moderate size network that I'm trying to bring some sanity to. Basically, its 8 public class Cs and a slew of private ranges all on one vlan (vlan1, of course). Most of the network is located throughout dark sites. I need to start separating some of the network. I've changed the ports from the main cisco switch (3560) to the cisco router (3825) and the other remote switches to trunking with dot1q encapsulation. I'd like to start moving a few select subnets to different vlans. To get some of the different services provided on our address space (and to separate customers) on to different vlans, do I need to create a subinterface on the router for each vlan and, if so, how do I get the switch port to work on a specific vlan? Keep in mind, these are dark sites and geting console access is difficult if not impossible at the moment. I was planning on creating a subinterface on the router for each vlan then setting the ports with services I want to move to a different vlan to allow only that vlan. Example of vlan3: 3825: interface GigabitEthernet0/1.3 description Vlan-3 encapsulation dot1Q 3 ip address 192.168.0.81 255.255.255.240 the connection between the switch and router: interface GigabitEthernet0/48 description Core-router switchport trunk encapsulation dot1q switchport mode trunk show interfaces gi0/48 switchport Name: Gi0/48 Switchport: Enabled Administrative Mode: trunk Operational Mode: trunk Administrative Trunking Encapsulation: dot1q Operational Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative Native VLAN tagging: enabled Voice VLAN: none Administrative private-vlan host-association: none Administrative private-vlan mapping: none Administrative private-vlan trunk native VLAN: none Administrative private-vlan trunk Native VLAN tagging: enabled Administrative private-vlan trunk encapsulation: dot1q Administrative private-vlan trunk normal VLANs: none Administrative private-vlan trunk private VLANs: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Protected: false Unknown unicast blocked: disabled Unknown multicast blocked: disabled Appliance trust: none So, if the boxen hanging off of gi0/18 on the 3560 are on an unmanaged layer2 switch and all within the 192.168.0.82-95 range and are using 192.168.0.81 as their gateway, what is left to do, especially to gi0/18, to get this working on vlan3? Are there any recommendations for a better setup without taking everything offline?

  Read the article

• FastCGI Error when installing PHP on IIS7.5

  - by ytoledano

  I'm trying to install MediaWiki on a Win2008r2 server, but can't manage to install PHP. Here's what I did: Grabbed a Zip archive of PHP and unzipped it into C:\PHP. Created two subdirs: c:\PHP\sessiondata and c:\PHP\uploadtemp. Granted modify rights to the IUSR account for the subdirs. Copied php.ini-production as php.ini Edited php.ini and made the following changes: fastcgi.impersonate = 1 cgi.fix_pathinfo = 1 cgi.force_redirect = 0 open_basedir = "c:\inetpub\wwwroot;c:\PHP\uploadtemp;C:\PHP\sessiondata" extension = php_mysql.dll extension_dir = "./ext" upload_tmp_dir = C:\PHP\uploadtemp session.save_path = C:\php\sessiondata Install Web server role, selected CGI and HTTP Redirection options. In the Handler Mappings: Added Module Mapping. Entered the following values: Path = *.php, Module = FastCgiModule, Executable = c:\php\php-cgi.exe, Name = PHP via FastCGI. Created a test page into wwwroot directory: phpinfo.php and set the contents like this: < ?php phpinfo(); ? Browsed to http://localhost/phpinfo.php But then I get: HTTP Error 500.0 - Internal Server Error An unknown FastCGI error occured Detailed Error Information Module: FastCgiModule Notification: ExecuteRequestHandler Handler: PHP via FastCGI Error Code: 0x800736b1 Requested URL: http://localhost:80/phpinfo.php Physical Path: C:\inetpub\wwwroot\phpinfo.php Logon Method: Anonymous Logon User: Anonymous Does anyone know what I'm doing wrong here? Thanks.

  Read the article

• How to convert an MKV to AVI with minimal loss

  - by Linux Jedi

  To convert an MKV to AVI, I do two things. The first thing I do is this: ffmpeg -i filename.mkv -vcodec copy -acodec copy output.avi This converts the MKV to an AVI, but the problem is that the video does not play smoothly for some reason. That's fine, because if I do one more thing it gets fixed: ffmpeg -i output.avi -vcodec mpeg4 -b 4000k -acodec mp2 -ab 320k converted.avi After I do this then the file plays without problem. I had success doing it this way for one file, but then I tried it on another file, and there is a slight, but noticeable loss in video quality. This is the output I get when doing the second step: FFmpeg version 0.6.1, Copyright (c) 2000-2010 the FFmpeg developers built on Dec 29 2010 18:02:10 with gcc 4.2.1 (Apple Inc. build 5664) configuration: libavutil 50.15. 1 / 50.15. 1 libavcodec 52.72. 2 / 52.72. 2 libavformat 52.64. 2 / 52.64. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0.11. 0 / 0.11. 0 Seems stream 0 codec frame rate differs from container frame rate: 359.00 (359/1) -> 29.92 (359/12) Input #0, avi, from 'output.avi': Metadata: ISFT : Lavf52.64.2 Duration: 00:04:17.21, start: 0.000000, bitrate: 3074 kb/s Stream #0.0: Video: mpeg4, yuv420p, 704x480 [PAR 229:189 DAR 5038:2835], 29.92 fps, 29.92 tbr, 29.92 tbn, 359 tbc Stream #0.1: Audio: vorbis, 48000 Hz, stereo, s16 Output #0, avi, to 'nidome_no_kanojo.avi': Metadata: ISFT : Lavf52.64.2 Stream #0.0: Video: mpeg4, yuv420p, 704x480 [PAR 229:189 DAR 5038:2835], q=2-31, 4000 kb/s, 29.92 tbn, 29.92 tbc Stream #0.1: Audio: mp2, 48000 Hz, stereo, s16, 320 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 I just used arbitrarily large settings on the second step and it worked nicely before but not in this case. What settings should I use?

  Read the article

• How is a subdomain passed to the webserver?

  - by Joshua Frank

  I know that dns resolves an address like example.com to an IP address like 11.22.33.44, but I'm a little confused about how subdomains are resolved, so that when you type http://subdomain.example.com, what actually gets passed to the server at 11.22.33.44? In other words, example.com = 11.22.33.44, but subdomain.example.com/path = ??? Are "subdomain" and "path" passed as http headers, or mapped in the url in some way, or what? Thanks in advance. Edit: If I'm understanding correctly, BloodPhilia says that subdomain.example.com actually is a different domain that in principle could resolve to a totally different IP. But if that's so, then what about hosts that have huge numbers of (what look like) subdomains, but which actually map to some path on the site. For instance, blogspot hosts millions of blogs, and they all look like this: aaa.blogspot.com bbb.blogspot.com ...millions more... yyy.blogspot.com zzz.blogspot.com Those are clearly not subdomains with their own IP's, but rather some mapping like aaa.blogspot.com -- www.blogspot.com/aaa, but how is this accomplished? What actually gets passed to the web server at blogspot.com?

  Read the article

• avconv gets killed if mkv has subtitles

  - by Lukas Knuth

  What I'm trying to do is to take a movie (in an Matroska container), convert all audio tracks to AC3 and don't touch anything else. I'm using this line: avconv -i infile.mkv -map 0 -vcodec copy -scodec copy -acodec ac3 -ab 256k outfile.mkv This works fine, except when there are subtitles embedded. Then, after some time processing with no progress, avconv just "dies" (output shortened, these seem to be the interesting parts): [matroska,webm @ 0xf867a0] max_analyze_duration reached [matroska,webm @ 0xf867a0] Estimating duration from bitrate, this may be inaccurate ... Incompatible sample format 's16' for codec 'ac3', auto-selecting format 'flt' ... Stream #0.0(eng): Video: H264 / 0x34363248, yuv420p, 1280x536 [PAR 1:1 DAR 160:67], q=2-31, 1k tbn, 1k tbc (default) Stream #0.1(ger): Audio: ac3, 48000 Hz, 5.1, flt, 256 kb/s (default) Stream #0.2(eng): Audio: ac3, 48000 Hz, 5.1, flt, 256 kb/s Stream #0.3(ger): Subtitle: dvdsub (default) (forced) Metadata: title : forced Stream #0.4(ger): Subtitle: dvdsub Metadata: title : complete Stream mapping: Stream #0:0 -> #0:0 (copy) Stream #0:1 -> #0:1 (dca -> ac3) Stream #0:2 -> #0:2 (dca -> ac3) Stream #0:3 -> #0:3 (copy) Stream #0:4 -> #0:4 (copy) Input stream #0:2 frame changed from rate:48000 fmt:s16 ch:6 to rate:48000 fmt:flt ch:6 Input stream #0:1 frame changed from rate:48000 fmt:s16 ch:6 to rate:48000 fmt:flt ch:6 frame= 2606 fps=1303 q=-1.0 size= 3kB time=107.36 bitrate= 0.2kbits/s ... frame=96141 fps=813 q=-1.0 size= 2195806kB time=2807.04 bitrate=6408.2kbits/s frame=96251 fps=810 q=-1.0 size= 2195806kB time=2807.04 bitrate=6408.2kbits/s ... frame=97015 fps=397 q=-1.0 size= 2195806kB time=2807.04 bitrate=6408.2kbits/s Getötet ["Killed", in English] I have no idea why this happens, as there is no error-output. I'd like to just copy the subtitles over, not touch them at all. If that won't work, they can be completely dropped.

  Read the article

< Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >