Search Results

Search found 10627 results on 426 pages for 'smart status'.

Page 106/426 | < Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >

• Western Digitial My Book: Can't access the data on the drive

  - by Bryan Denny

  My girlfriend has this external hard drive by Western Digital called a My Book. When the external drive is connected, it does not show it as an accessible disk drive on the computer. However, it shows up fine in Device Manager: I can also see it in Disk Management, but the volume is not mapped to a drive letter, nor can I change the drive letter: It only gives me access to Delete Volume: I would rather not lose the data on the drive if possible. What can I do from here to get to the data? Things I've tried/know: Uninstall drivers and re-install them Device does the same thing when attach to either her Win7 laptop or my Win8 laptop I don't think there's an issue with the HDD itself. No clicking noises, etc. I ran Western Digital Data LifeGuard Diangostics (DLGDIAG) and the SMART Status was a "PASS", all of the SMART Disk Information looked fine. I haven't had the time to run the diag tests yet but I do not believe it's a mechanical issue. The hard drive is inside of an enclosure, I have not attempted to pry the drive out yet. How can I get Windows to properly detect this drive?

  Read the article

• HAproxy with MySQL Master-Master Replication incredibly slow

  - by Yayap

  I have two MySQL servers in multi-master mode, with an HAproxy machine for simple load balancing/redundancy. When I am connected to one of the servers directly and try to update about 100,000 entries, it is completed including replication in about half a minute. When connecting through the proxy it takes usually over three whole minutes. Is it normal to have that type of latency? Is something amiss with my proxy configuration (included below)? This is getting really frustrating as I assumed the proxy would do some sort of load balancing, or at least have little to no overhead. #--------------------------------------------------------------------- # Example configuration for a possible web application. See the # full configuration options online. # # http://haproxy.1wt.eu/download/1.4/doc/configuration.txt # #--------------------------------------------------------------------- #--------------------------------------------------------------------- # Global settings #--------------------------------------------------------------------- global # to have these messages end up in /var/log/haproxy.log you will # need to: # # 1) configure syslog to accept network log events. This is done # by adding the '-r' option to the SYSLOGD_OPTIONS in # /etc/sysconfig/syslog # # 2) configure local2 events to go to the /var/log/haproxy.log # file. A line like the following can be added to # /etc/sysconfig/syslog # # local2.* /var/log/haproxy.log # log 127.0.0.1 local2 # chroot /var/lib/haproxy # pidfile /var/run/haproxy.pid maxconn 4096 user haproxy group haproxy daemon #debug #quiet # turn on stats unix socket stats socket /var/lib/haproxy/stats #--------------------------------------------------------------------- # common defaults that all the 'listen' and 'backend' sections will # use if not designated in their block #--------------------------------------------------------------------- defaults mode tcp log global #option tcplog option dontlognull option tcp-smart-accept option tcp-smart-connect #option http-server-close #option forwardfor except 127.0.0.0/8 #option redispatch retries 3 #timeout http-request 10s #timeout queue 1m timeout connect 400 timeout client 500 timeout server 300 #timeout http-keep-alive 10s #timeout check 10s maxconn 2000 listen mysql-cluster 0.0.0.0:3306 mode tcp balance roundrobin option tcpka option httpchk server db01 192.168.15.118:3306 weight 1 inter 1s rise 1 fall 1 server db02 192.168.15.119:3306 weight 1 inter 1s rise 1 fall 1

  Read the article

• Is execution of sync(8) still required before shutting down linux?

  - by Amos Shapira

  I still see people recommend use of "sync; sync; sync; sleep 30; halt" incantations when talking about shutting down or rebooting Linux. I've been running Linux since its inception and although this was the recommended procedure in the BSD 4.2/4.3 and SunOS 4 days, I can't recall that I had to do that for at least the last ten years, during which I probably went through shutdown/reboot of Linux maybe thousands of times. I suspect that this is an anachronism since the days that the kernel couldn't unmount and sync the root filesystem and other critical filesystems required even during single-user mode (e.g. /tmp), and therefore it was necessary to tell it explicitly to flush as much data as it can to disk. These days, without finding the relevant code in the kernel source yet (digging through http://lxr.linux.no and google), I suspect that the kernel is smart enough to cleanly unmount even the root filesystem and the filesystem is smart enough to effectively do a sync(2) before unmounting itself during a normal "shutdown"/"reboot"/"poweorff". The "sync; sync; sync" is only necessary in extreme cases where the filesystem won't unmount cleanly (e.g. physical disk failure) or the system is in a state that only forcing a direct reboot(8) will get it out of its freeze (e.g. the load is too high to let it schedule the shutdown command). I also never do the "sync" procedure before unmounting removable devices, and never hit a problem. Another example - Xen allows the DomU to be sent a "shutdown" command from the Dom0, this is considered a "clean shutdown" without anyone having to login and type the magical "sync; sync; sync" first. Am I right or was I lucky for a few thousands of system shutdowns?

  Read the article

• Exchange 2010 sends out spam.

  - by Magnus Gladh

  Hi. I have an Exchange Server 2010, that uses a smart host to send out mails. A day ago the owner of smart host contact us and told us that we send out spam. I have try different open relay test on the net and all of them come back saying that this server is secured and can not be used as relay server. But I can see in my Exchange Queue Viewer that it keeps coming in new messages. Here is an example of how it looks. Identity: mailserver\3874\13128 Subject: Olevererbart:: [email protected] Pfizer -75% now Internet Message ID: <[email protected]> From Address: <> Status: Ready Size (KB): 6 Message Source Name: DSN Source IP: 255.255.255.255 SCL: -1 Date Received: 2010-12-09 21:46:22 Expiration Time: 2010-12-11 21:46:22 Last Error: Queue ID: mailserver\3874 Recipients: [email protected] How can I secure our exchange server more, to stop this from happening? Could I have got an virus that hooks up to our exchange server and send mail throw that? As I can see the From Address is always <, is there someway that I can stop sending mails that don't have a from address that I describe? Pleas help

  Read the article

• Can Spotlight or Media Browser index metadata contained in iPhoto or Aperture in Mac OS X?

  - by jaydles

  It seems silly to go to all the trouble to assign "Face" data to thousands of photos, but not make it possible to use that data to locate them outside of that application. Is there any way to get Spotlight or Media Browser in OSX (Snow Leopard) to index and recognize metadata (Faces, Places, etc.) contained in iPhoto or Aperture? I know that that metadata is stored in the "library" database for Aperture/iphoto, rather than on the actual files (which is too bad). And I can even potentially see why it might create challenges for spotlight to use it, since spotlight is presumably a file index system, not a media organizer, but surely the media browser used across the other OSX apps is intended to use it? The media browser's whole purpose seems to be to let you easily locate and reference the items you organize in one of the ilife apps (iphoto or Aperture, in this case) from the others (say, imovie, or Mail). It's particularly vexing since the photo app on the iphone sorts by faces by default. Additionally, the mac-based media browser does access smart albums and folders, so you could establish a workaround by creating a smart album for each "face" or place, or tag, and access them that way, but it seems like there must be an easier way. Am I missing something?

  Read the article

• Remote Desktop Zooming

  - by codeulike

  Using Remote Desktop from a device with a hi-res screen (say, a Surface Pro) is decidedly tricky - as everything displays 1:1 scale and so looks tiny. If the machine you are remoting into runs Server 2008 R2 or later, you can change the dpi zooming setting (see here). But for older hosts, that doesn't work. Using normal Remote Desktop, you can connect with a lower resolution, say 1280x768, and turn on smart-sizing. However smart-sizing can scale down (to display a huge desktop in a small area) but does not seem to scale up (to display a small desktop in a big area). Using the Windows 8 Remote Desktop App, you can zoom - but you cannot set the default resolution of the host. What I want is a lower resolution in the host, scaled up to fit my screen. So both of those are close to what I want, but dont quite work. So question is: Does the Remote Desktop App allow screen resolution to be set somehow? Is there some other Remote Desktop client that can handle zooming better?

  Read the article

• Recommended Win2k8 Server software to fix my RAID-0 issue

  - by Jason Kealey

  I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

  Read the article

• Western Digital HDD disappears and reappears in BIOS

  - by tbkn23

  I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

  Read the article

• Is there any way to get spotlight or media browser in OSX (Snow Leopard) to index and recognize meta

  - by jaydles

  It seems silly to go to all the trouble to assign "Face" data to thousands of photos, but not make it possible to use that data to locate them outside of that application. I know that that metadata is stored in the "library" database for Aperture/iphoto, rather than on the actual files (which is too bad). And I can even potentially see why it might create challenges for spotlight to use it, since spotlight if presumably a file index system, not a media organizer, but surely the media browser used across the other OSX apps is intended to use it? The media browser's whole purpose seems to be to let you easily locate and reference the items you organize in one of the ilife apps (iphoto or Aperture, in this case) from the others (say, imovie, or Mail). It's particularly vexing since the photo app on the iphone sorts by faces by default. Additionally, the mac-based media browser does access smart albums and folders, so you could establish a workaround by creating a smart album for each "face" or place, or tag, and access them that way, but it seems like there must be an easier way. Am I missing something?

  Read the article

• Security Token for Mac/Linux/Windows, self-managed, pref. open source?

  - by DevelopersDevelopersDevelopers

  I'm looking to buy an evaluation security token (combined smart card/usb reader) for my business that works on: Windows 7 x64 OS X 10.6.x x64 Ubuntu Linux (64 or 32 bit, 10.04 or 10.10, I can bend based on possible tokens) Functionality I need is: Login authentication Authentication for whole-disk encryption (in Linux/Windows, Mac is flexible here) Signing/encryption using PGP and x.509 certificates RSA-2048 key-capable (1024 not good enough.) I can manage the certificates myself Open source middleware/drivers (not necessarily FOSS, just source available. Can flex on this, I just want to be able to audit the code. OpenSC-compatible on Linux would be great.) Is there any token that can do all of this? Or would I need multiple ones to accomplish this? Or do I need to look at smart cards and readers to get this? I have been researching this for a while and have had a heck of a time even getting accurate information about products. Also, I am in the USA, and it appears that EU export laws prevent me from buying from there, so those vendors are out. I was looking at Feitian tokens from Gooze, but since they are in France I can't buy.

  Read the article

• Fed Authentication Methods in OIF / IdP

  - by Damien Carru

  This article is a continuation of my previous entry where I explained how OIF/IdP leverages OAM to authenticate users at runtime: OIF/IdP internally forwards the user to OAM and indicates which Authentication Scheme should be used to challenge the user if needed OAM determine if the user should be challenged (user already authenticated, session timed out or not, session authentication level equal or higher than the level of the authentication scheme specified by OIF/IdP…) After identifying the user, OAM internally forwards the user back to OIF/IdP OIF/IdP can resume its operation In this article, I will discuss how OIF/IdP can be configured to map Federation Authentication Methods to OAM Authentication Schemes: When processing an Authn Request, where the SP requests a specific Federation Authentication Method with which the user should be challenged When sending an Assertion, where OIF/IdP sets the Federation Authentication Method in the Assertion Enjoy the reading! Overview The various Federation protocols support mechanisms allowing the partners to exchange information on: How the user should be challenged, when the SP/RP makes a request How the user was challenged, when the IdP/OP issues an SSO response When a remote SP partner redirects the user to OIF/IdP for Federation SSO, the message might contain data requesting how the user should be challenged by the IdP: this is treated as the Requested Federation Authentication Method. OIF/IdP will need to map that Requested Federation Authentication Method to a local Authentication Scheme, and then invoke OAM for user authentication/challenge with the mapped Authentication Scheme. OAM would authenticate the user if necessary with the scheme specified by OIF/IdP. Similarly, when an IdP issues an SSO response, most of the time it will need to include an identifier representing how the user was challenged: this is treated as the Federation Authentication Method. When OIF/IdP issues an Assertion, it will evaluate the Authentication Scheme with which OAM identified the user: If the Authentication Scheme can be mapped to a Federation Authentication Method, then OIF/IdP will use the result of that mapping in the outgoing SSO response: AuthenticationStatement in the SAML Assertion OpenID Response, if PAPE is enabled If the Authentication Scheme cannot be mapped, then OIF/IdP will set the Federation Authentication Method as the Authentication Scheme name in the outgoing SSO response: AuthenticationStatement in the SAML Assertion OpenID Response, if PAPE is enabled Mappings In OIF/IdP, the mapping between Federation Authentication Methods and Authentication Schemes has the following rules: One Federation Authentication Method can be mapped to several Authentication Schemes In a Federation Authentication Method <-> Authentication Schemes mapping, a single Authentication Scheme is marked as the default scheme that will be used to authenticate a user, if the SP/RP partner requests the user to be authenticated via a specific Federation Authentication Method An Authentication Scheme can be mapped to a single Federation Authentication Method Let’s examine the following example and the various use cases, based on the SAML 2.0 protocol: Mappings defined as: urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport mapped to LDAPScheme, marked as the default scheme used for authentication BasicScheme urn:oasis:names:tc:SAML:2.0:ac:classes:X509 mapped to X509Scheme, marked as the default scheme used for authentication Use cases: SP sends an AuthnRequest specifying urn:oasis:names:tc:SAML:2.0:ac:classes:X509 as the RequestedAuthnContext: OIF/IdP will authenticate the use with X509Scheme since it is the default scheme mapped for that method. SP sends an AuthnRequest specifying urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport as the RequestedAuthnContext: OIF/IdP will authenticate the use with LDAPScheme since it is the default scheme mapped for that method, not the BasicScheme SP did not request any specific methods, and user was authenticated with BasisScheme: OIF/IdP will issue an Assertion with urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport as the FederationAuthenticationMethod SP did not request any specific methods, and user was authenticated with LDAPScheme: OIF/IdP will issue an Assertion with urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport as the FederationAuthenticationMethod SP did not request any specific methods, and user was authenticated with BasisSessionlessScheme: OIF/IdP will issue an Assertion with BasisSessionlessScheme as the FederationAuthenticationMethod, since that scheme could not be mapped to any Federation Authentication Method (in this case, the administrator would need to correct that and create a mapping) Configuration Mapping Federation Authentication Methods to OAM Authentication Schemes is protocol dependent, since the methods are defined in the various protocols (SAML 2.0, SAML 1.1, OpenID 2.0). As such, the WLST commands to set those mappings will involve: Either the SP Partner Profile and affect all Partners referencing that profile, which do not override the Federation Authentication Method to OAM Authentication Scheme mappings Or the SP Partner entry, which will only affect the SP Partner It is important to note that if an SP Partner is configured to define one or more Federation Authentication Method to OAM Authentication Scheme mappings, then all the mappings defined in the SP Partner Profile will be ignored. Authentication Schemes As discussed in the previous article, during Federation SSO, OIF/IdP will internally forward the user to OAM for authentication/verification and specify which Authentication Scheme to use. OAM will determine if a user needs to be challenged: If the user is not authenticated yet If the user is authenticated but the session timed out If the user is authenticated, but the authentication scheme level of the original authentication is lower than the level of the authentication scheme requested by OIF/IdP So even though an SP requests a specific Federation Authentication Method to be used to challenge the user, if that method is mapped to an Authentication Scheme and that at runtime OAM deems that the user does not need to be challenged with that scheme (because the user is already authenticated, session did not time out, and the session authn level is equal or higher than the one for the specified Authentication Scheme), the flow won’t result in a challenge operation. Protocols SAML 2.0 The SAML 2.0 specifications define the following Federation Authentication Methods for SAML 2.0 flows: urn:oasis:names:tc:SAML:2.0:ac:classes:unspecified urn:oasis:names:tc:SAML:2.0:ac:classes:InternetProtocol urn:oasis:names:tc:SAML:2.0:ac:classes:Telephony urn:oasis:names:tc:SAML:2.0:ac:classes:MobileOneFactorUnregistered urn:oasis:names:tc:SAML:2.0:ac:classes:PersonalTelephony urn:oasis:names:tc:SAML:2.0:ac:classes:PreviousSession urn:oasis:names:tc:SAML:2.0:ac:classes:MobileOneFactorContract urn:oasis:names:tc:SAML:2.0:ac:classes:Smartcard urn:oasis:names:tc:SAML:2.0:ac:classes:Password urn:oasis:names:tc:SAML:2.0:ac:classes:InternetProtocolPassword urn:oasis:names:tc:SAML:2.0:ac:classes:X509 urn:oasis:names:tc:SAML:2.0:ac:classes:TLSClient urn:oasis:names:tc:SAML:2.0:ac:classes:PGP urn:oasis:names:tc:SAML:2.0:ac:classes:SPKI urn:oasis:names:tc:SAML:2.0:ac:classes:XMLDSig urn:oasis:names:tc:SAML:2.0:ac:classes:SoftwarePKI urn:oasis:names:tc:SAML:2.0:ac:classes:Kerberos urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport urn:oasis:names:tc:SAML:2.0:ac:classes:SecureRemotePassword urn:oasis:names:tc:SAML:2.0:ac:classes:NomadTelephony urn:oasis:names:tc:SAML:2.0:ac:classes:AuthenticatedTelephony urn:oasis:names:tc:SAML:2.0:ac:classes:MobileTwoFactorUnregistered urn:oasis:names:tc:SAML:2.0:ac:classes:MobileTwoFactorContract urn:oasis:names:tc:SAML:2.0:ac:classes:SmartcardPKI urn:oasis:names:tc:SAML:2.0:ac:classes:TimeSyncToken Out of the box, OIF/IdP has the following mappings for the SAML 2.0 protocol: Only urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport is defined This Federation Authentication Method is mapped to: LDAPScheme, marked as the default scheme used for authentication FAAuthScheme BasicScheme BasicFAScheme This mapping is defined in the saml20-sp-partner-profile SP Partner Profile which is the default OOTB SP Partner Profile for SAML 2.0 An example of an AuthnRequest message sent by an SP to an IdP with the SP requesting a specific Federation Authentication Method to be used to challenge the user would be: <samlp:AuthnRequest xmlns:samlp="urn:oasis:names:tc:SAML:2.0:protocol" Destination="https://idp.com/oamfed/idp/samlv20" ID="id-8bWn-A9o4aoMl3Nhx1DuPOOjawc-" IssueInstant="2014-03-21T20:51:11Z" Version="2.0">  <saml:Issuer ...>https://acme.com/sp</saml:Issuer>  <samlp:NameIDPolicy AllowCreate="false" Format="urn:oasis:names:tc:SAML:1.1:nameid-format:unspecified"/>  <samlp:RequestedAuthnContext Comparison="minimum">    <saml:AuthnContextClassRef xmlns:saml="urn:oasis:names:tc:SAML:2.0:assertion">      urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport </saml:AuthnContextClassRef>  </samlp:RequestedAuthnContext></samlp:AuthnRequest> An example of an Assertion issued by an IdP would be: <samlp:Response ...>    <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer>    <samlp:Status>        <samlp:StatusCode Value="urn:oasis:names:tc:SAML:2.0:status:Success"/>    </samlp:Status>    <saml:Assertion ...>        <saml:Issuer ...>https://idp.com/oam/fed</saml:Issuer>        <dsig:Signature>            ...        </dsig:Signature>        <saml:Subject>            <saml:NameID ...>[email protected]</saml:NameID>            <saml:SubjectConfirmation Method="urn:oasis:names:tc:SAML:2.0:cm:bearer">                <saml:SubjectConfirmationData .../>            </saml:SubjectConfirmation>        </saml:Subject>        <saml:Conditions ...>            <saml:AudienceRestriction>                <saml:Audience>https://acme.com/sp</saml:Audience>            </saml:AudienceRestriction>        </saml:Conditions>        <saml:AuthnStatement AuthnInstant="2014-03-21T20:53:55Z" SessionIndex="id-6i-Dm0yB-HekG6cejktwcKIFMzYE8Yrmqwfd0azz" SessionNotOnOrAfter="2014-03-21T21:53:55Z">            <saml:AuthnContext>                <saml:AuthnContextClassRef>                    urn:oasis:names:tc:SAML:2.0:ac:classes:PasswordProtectedTransport                </saml:AuthnContextClassRef>            </saml:AuthnContext>        </saml:AuthnStatement>    </saml:Assertion></samlp:Response> An administrator would be able to specify a mapping between a SAML 2.0 Federation Authentication Method and one or more OAM Authentication Schemes SAML 1.1 The SAML 1.1 specifications define the following Federation Authentication Methods for SAML 1.1 flows: urn:oasis:names:tc:SAML:1.0:am:unspecified urn:oasis:names:tc:SAML:1.0:am:HardwareToken urn:oasis:names:tc:SAML:1.0:am:password urn:oasis:names:tc:SAML:1.0:am:X509-PKI urn:ietf:rfc:2246 urn:oasis:names:tc:SAML:1.0:am:PGP urn:oasis:names:tc:SAML:1.0:am:SPKI urn:ietf:rfc:3075 urn:oasis:names:tc:SAML:1.0:am:XKMS urn:ietf:rfc:1510 urn:ietf:rfc:2945 Out of the box, OIF/IdP has the following mappings for the SAML 1.1 protocol: Only urn:oasis:names:tc:SAML:1.0:am:password is defined This Federation Authentication Method is mapped to: LDAPScheme, marked as the default scheme used for authentication FAAuthScheme BasicScheme BasicFAScheme This mapping is defined in the saml11-sp-partner-profile SP Partner Profile which is the default OOTB SP Partner Profile for SAML 1.1 An example of an Assertion issued by an IdP would be: <samlp:Response ...>    <samlp:Status>        <samlp:StatusCode Value="samlp:Success"/>    </samlp:Status>    <saml:Assertion Issuer="https://idp.com/oam/fed" ...>        <saml:Conditions ...>            <saml:AudienceRestriction>                <saml:Audience>https://acme.com/sp/ssov11</saml:Audience>            </saml:AudienceRestriction>        </saml:Conditions>        <saml:AuthnStatement AuthenticationInstant="2014-03-21T20:53:55Z" AuthenticationMethod="urn:oasis:names:tc:SAML:1.0:am:password">            <saml:Subject>                <saml:NameID ...>[email protected]</saml:NameID>                <saml:SubjectConfirmation>                   <saml:ConfirmationMethod>                       urn:oasis:names:tc:SAML:1.0:cm:bearer                   </saml:ConfirmationMethod>                </saml:SubjectConfirmation>            </saml:Subject>        </saml:AuthnStatement>        <dsig:Signature>            ...        </dsig:Signature>    </saml:Assertion></samlp:Response> Note: SAML 1.1 does not define an AuthnRequest message. An administrator would be able to specify a mapping between a SAML 1.1 Federation Authentication Method and one or more OAM Authentication Schemes OpenID 2.0 The OpenID 2.0 PAPE specifications define the following Federation Authentication Methods for OpenID 2.0 flows: http://schemas.openid.net/pape/policies/2007/06/phishing-resistant http://schemas.openid.net/pape/policies/2007/06/multi-factor http://schemas.openid.net/pape/policies/2007/06/multi-factor-physical Out of the box, OIF/IdP does not define any mappings for the OpenID 2.0 Federation Authentication Methods. For OpenID 2.0, the configuration will involve mapping a list of OpenID 2.0 policies to a list of Authentication Schemes. An example of an OpenID 2.0 Request message sent by an SP/RP to an IdP/OP would be: https://idp.com/openid?openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=checkid_setup&openid.claimed_id=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0%2Fidentifier_select&openid.identity=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0%2Fidentifier_select&openid.assoc_handle=id-6a5S6zhAKaRwQNUnjTKROREdAGSjWodG1el4xyz3&openid.return_to=https%3A%2F%2Facme.com%2Fopenid%3Frefid%3Did-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.realm=https%3A%2F%2Facme.com%2Fopenid&openid.ns.ax=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ax.mode=fetch_request&openid.ax.type.attr0=http%3A%2F%2Faxschema.org%2Fcontact%2Femail&openid.ax.if_available=attr0&openid.ns.pape=http%3A%2F%2Fspecs.openid.net%2Fextensions%2Fpape%2F1.0&openid.pape.max_auth_age=0 An example of an Open ID 2.0 SSO Response issued by an IdP/OP would be: https://acme.com/openid?refid=id-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.ns=http%3A%2F%2Fspecs.openid.net%2Fauth%2F2.0&openid.mode=id_res&openid.op_endpoint=https%3A%2F%2Fidp.com%2Fopenid&openid.claimed_id=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.identity=https%3A%2F%2Fidp.com%2Fopenid%3Fid%3Did-38iCmmlAVEXPsFjnFVKArfn5RIiF75D5doorhEgqqPM%3D&openid.return_to=https%3A%2F%2Facme.com%2Fopenid%3Frefid%3Did-9PKVXZmRxAeDYcgLqPm36ClzOMA-&openid.response_nonce=2014-03-24T19%3A20%3A06Zid-YPa2kTNNFftZkgBb460jxJGblk2g--iNwPpDI7M1&openid.assoc_handle=id-6a5S6zhAKaRwQNUnjTKROREdAGSjWodG1el4xyz3&openid.ns.ax=http%3A%2F%2Fopenid.net%2Fsrv%2Fax%2F1.0&openid.ax.mode=fetch_response&openid.ax.type.attr0=http%3A%2F%2Fsession%2Fcount&openid.ax.value.attr0=1&openid.ax.type.attr1=http%3A%2F%2Fopenid.net%2Fschema%2FnamePerson%2Ffriendly&openid.ax.value.attr1=My+name+is+Bobby+Smith&openid.ax.type.attr2=http%3A%2F%2Fschemas.openid.net%2Fax%2Fapi%2Fuser_id&openid.ax.value.attr2=bob&openid.ax.type.attr3=http%3A%2F%2Faxschema.org%2Fcontact%2Femail&openid.ax.value.attr3=bob%40oracle.com&openid.ax.type.attr4=http%3A%2F%2Fsession%2Fipaddress&openid.ax.value.attr4=10.145.120.253&openid.ns.pape=http%3A%2F%2Fspecs.openid.net%2Fextensions%2Fpape%2F1.0&openid.pape.auth_time=2014-03-24T19%3A20%3A05Z&openid.pape.auth_policies=http%3A%2F%2Fschemas.openid.net%2Fpape%2Fpolicies%2F2007%2F06%2Fphishing-resistant&openid.signed=op_endpoint%2Cclaimed_id%2Cidentity%2Creturn_to%2Cresponse_nonce%2Cassoc_handle%2Cns.ax%2Cax.mode%2Cax.type.attr0%2Cax.value.attr0%2Cax.type.attr1%2Cax.value.attr1%2Cax.type.attr2%2Cax.value.attr2%2Cax.type.attr3%2Cax.value.attr3%2Cax.type.attr4%2Cax.value.attr4%2Cns.pape%2Cpape.auth_time%2Cpape.auth_policies&openid.sig=mYMgbGYSs22l8e%2FDom9NRPw15u8%3D In the next article, I will provide examples on how to configure OIF/IdP for the various protocols, to map OAM Authentication Schemes to Federation Authentication Methods.Cheers,Damien Carru

  Read the article

• sp_send_dbmail attach files stored as varbinary in database

  - by Mindstorm Interactive

  I have a two part question relating to sending query results as attachments using sp_send_dbmail. Problem 1: Only basic .txt files will open. Any other format like .pdf or .jpg are corrupted. Problem 2: When attempting to send multiple attachments, I receive one file with all file names glued together. I'm running SQL Server 2005 and I have a table storing uploaded documents: CREATE TABLE [dbo].[EmailAttachment]( [EmailAttachmentID] [int] IDENTITY(1,1) NOT NULL, [MassEmailID] [int] NULL, -- foreign key [FileData] [varbinary](max) NOT NULL, [FileName] [varchar](100) NOT NULL, [MimeType] [varchar](100) NOT NULL I also have a MassEmail table with standard email stuff. Here is the SQL Send Mail script. For brevity, I've excluded declare statements. while ( (select count(MassEmailID) from MassEmail where status = 20 )>0) begin select @MassEmailID = Min(MassEmailID) from MassEmail where status = 20 select @Subject = [Subject] from MassEmail where MassEmailID = @MassEmailID select @Body = Body from MassEmail where MassEmailID = @MassEmailID set @query = 'set nocount on; select cast(FileData as varchar(max)) from Mydatabase.dbo.EmailAttachment where MassEmailID = '+ CAST(@MassEmailID as varchar(100)) select @filename = '' select @filename = COALESCE(@filename+ ',', '') +FileName from EmailAttachment where MassEmailID = @MassEmailID exec msdb.dbo.sp_send_dbmail @profile_name = 'MASS_EMAIL', @recipients = '[email protected]', @subject = @Subject, @body =@Body, @body_format ='HTML', @query = @query, @query_attachment_filename = @filename, @attach_query_result_as_file = 1, @query_result_separator = '; ', @query_no_truncate = 1, @query_result_header = 0; update MassEmailset status= 30,SendDate = GetDate() where MassEmailID = @MassEmailID end I am able to successfully read files from the database so I know the binary data is not corrupted. .txt files only read when I cast FilaData to varchar. But clearly original headers are lost. It's also worth noting that attachment file sizes are different than the original files. That is most likely due to improper encoding as well. So I'm hoping there's a way to create file headers using the stored mimetype, or some way to include file headers in the binary data? I'm also not confident in the values of the last few parameters, and I know coalesce is not quite right, because it prepends the first file name with a comma. But good documentation is nearly impossible to find. Please help!

  Read the article

• jqGrid dynamic select option - beforeEditCell not firing

  - by mango

  I'm creating a jqgrid with one drop down column. I need the options of the drop down columns to change dynamically so I thought I can catch the beforeCellEdit event. however it does not seem to be firing. any idea on what i am doing wrong? there is no error, and i did check that i have included the jqgrid edit js files. var lastsel2; jQuery(document).ready(function(){ jQuery("#projectList").jqGrid({ datatype: 'json', url:'projectDrv.jsp', mtype: 'GET', height: 250, colNames:['Node','Proposal #', 'Status', 'Vendor', 'Actions'], colModel :[ {name:'node', index:'node', width:100, editable:false, sortable:false}, {name:'proposal', index:'proposal', width:100, editable:false, resizable:true }, {name:'status', index:'status', width:100, resizable:true, sortable:false, editable:false }, {name:'vendor', index:'vendor', width:100, resizable:true, editable:false, sortable: false }, {name:'actions', index:'actions', width:100, resizable:true, sortable:false, editable: true, edittype:"select" } ], pager: '#pager', rowNum: 10, sortname: 'proposal', sortorder: 'desc', viewrecords: true, onSelectRow: function(id){ if (id && id!==lastsel2){ jQuery('#projectList').jqGrid('restoreRow',lastsel2); jQuery('#projectList').jqGrid('editRow',id,true); lastsel2 = id; } }, beforeEditCell: function(rowid, cellname, value, irow, icol) { alert("before edit here " + rowid); // set editoptions here } });

  Read the article

• Using Perl WWW::Facebook::API to Publish To Facebook Newsfeed

  - by Russell C.

  We use Facebook Connect on our site in conjunction with the WWW::Facebook::API CPAN module to publish to our users newsfeed when requested by the user. So far we've been able to successfully update the user's status using the following code: use WWW::Facebook::API; my $facebook = WWW::Facebook::API->new( desktop => 0, api_key => $fb_api_key, secret => $fb_secret, session_key => $query->cookie($fb_api_key.'_session_key'), session_expires => $query->cookie($fb_api_key.'_expires'), session_uid => $query->cookie($fb_api_key.'_user') ); my $response = $facebook->stream->publish( message => qq|Test status message|, ); However, when we try to update the code above so we can publish newsfeed stories that include attachments and action links as specified in the Facebook API documentation for Stream.Publish, we have tried about 100 different ways without any success. According to the CPAN documentation all we should have to do is update our code to something like the following and pass the attachments & action links appropriately which doesn't seem to work: my $response = $facebook->stream->publish( message => qq|Test status message|, attachment => $json, action_links => [@links], ); For example, we are passing the above arguments as follows: $json = qq|{ 'name': 'i\'m bursting with joy', 'href': ' http://bit.ly/187gO1', 'caption': '{*actor*} rated the lolcat 5 stars', 'description': 'a funny looking cat', 'properties': { 'category': { 'text': 'humor', 'href': 'http://bit.ly/KYbaN'}, 'ratings': '5 stars' }, 'media': [{ 'type': 'image', 'src': 'http://icanhascheezburger.files.wordpress.com/2009/03/funny-pictures-your-cat-is-bursting-with-joy1.jpg', 'href': 'http://bit.ly/187gO1'}] }|; @links = ["{'text':'Link 1', 'href':'http://www.link1.com'}","{'text':'Link 2', 'href':'http://www.link2.com'}"]; The above, nor any of the other representations we tried seem to work. I'm hoping some other perl developer out there has this working and can explain how to create the attachment and action_links variables appropriately in Perl for posting to the Facebook news feed through WWW::Facebook::API. Thanks in advance for your help!

  Read the article

• Adding a UINavigationController as a subview of UIView

  - by eagle

  I'm trying to display a UILabel on top of a UINavigationController. The problem is that when I add the UILabel as a subview of UIWindow it will not automatically rotate since it is not a subview of UIViewController (UIViewController automatically handles updating subviews during rotations). This is the hierarchy I was using: UIWindow UILabel UINavigationController So I was thinking I could use the following hierarchy: UIWindow UIViewController UIView UILabel UINavigationController This way the label could be displayed on top of the UINavigationController's bar while also automatically being rotated since it is a subview of UIViewController. The problem is that when I try adding a UINavigationController as a subview of a view: [myViewController.view addSubview:myNavigationController.view]; it will appear 20 pixels downwards. Which I'm guessing is because it thinks it needs to make room for the status bar. But, since the UINavigationController is being placed inside a UIView which does not overlay on top of the status bar, it is incorrectly adding an additional 20 pixels. In other words, the top of the UINavigationBar is at the screen's 40 pixel mark instead of at 20 pixels. Is there any easy way to just shift the UINavigationController and all of its elements (e.g. navigation bar, tool bar, root view controller) up 20 pixels? Or to let it know that it shouldn't compensate for a status bar? If not, I guess I would need to use my first hierarchy mentioned above and figure out how to rotate the label so it is consistent with the navigation bar's rotation. Where can I find more information on how to do this? Note: by "displaying a label on top of the navigation bar", I mean it should overlay on top of the navigation bar... it can't simply be wrapped in a bar button item and placed as one of the items of the navigation bar.

  Read the article

• Forcing UIInterfaceOrientation changes on iPhone

  - by Andiih

  I'm strugging with getting an iPhone application which requires just about every push or pop in the Nav Controller Stack to change orientation. Basically the first view is portrait, the second landscape the third portrait again (Yes I know this is less than ideal, but that's the design and I've got to implement it). I've been through various advice on here.... http://stackoverflow.com/questions/995723/how-do-i-detect-a-rotation-on-the-iphone-without-the-device-autorotating http://stackoverflow.com/questions/1824682/force-portrait-orientation-on-pushing-new-view-to-uinavigationviewcontroller http://stackoverflow.com/questions/181780/is-there-a-documented-way-to-set-the-iphone-orientation But without total success. Setting to link against 3.1.2 my reading of the linked articles above seems to indicate that if my portrait view pushes a view with - (BOOL)shouldAutorotateToInterfaceOrientation:(UIInterfaceOrientation)interfaceOrientation { // Return YES for supported orientations return ((interfaceOrientation == UIInterfaceOrientationLandscapeRight) ); } Then then that view should appear rotated to landscape. What happens is it appears in its "broken" portrait form, then rotates correctly as the device is turned. If I pop the controller back to my portrait view (which has an appropriate shouldAutoRotate...) then that remains in broken landscape view until the device is returned to portrait orientation. I've also tried removing all the shouldautorotate messages, and instead forcing rotation by transforming the view. This kind of works, and I've figured out that by moving the status bar (which is actually hidden in my application) [UIApplication sharedApplication].statusBarOrientation = UIInterfaceOrientationLandscapeRight; the keyboard will appear with the correct orientation when desired. The problem with this approach is that the status bar transform is weird and ugly when you don't have a status bar - a shadow looms over the page with each change. So. What am I missing. 1) Am I wrong in thinking that in 3.1.2 (or possibly earlier) shouldAutorotateToInterfaceOrientation should provide the desired orientation simply by pushing controllers ? 2) Is there another way of getting keyboards to appear in the correct orientation. 3) Are the undocumented API calls the way to go (please no!)

  Read the article

• How to do server-side validation using Jqgrid?

  - by Eoghan

  Hi, I'm using jqgrid to display a list of sites and I want to do some server side validation when a site is added or edited. (Form editing rather than inline. Validation needs to be server side for various reasons I won't go into.) I thought the best way would be to check the data via an ajax request when the beforeSubmit event is triggered. However this only seems to work when I'm editing an existing row in the grid - the function isn't called when I add a new row. Have I got my beforeSubmit in the wrong place? Thanks for your help. $("#sites-grid").jqGrid({ url:'/json/sites', datatype: "json", mtype: 'GET', colNames:['Code', 'Name', 'Area', 'Cluster', 'Date Live', 'Status', 'Lat', 'Lng'], colModel :[ {name:'code', index:'code', width:80, align:'left', editable:true}, {name:'name', index:'name', width:250, align:'left', editrules:{required:true}, editable:true}, {name:'area', index:'area', width:60, align:'left', editable:true}, {name:'cluster_id', index:'cluster_id', width:80, align:'right', editrules:{required:true, integer:true}, editable:true, edittype:"select", editoptions:{value:"<?php echo $cluster_options; ?>"}}, {name:'estimated_live_date', index:'estimated_live_date', width:120, align:'left', editable:true, editrules:{required:true}, edittype:"select", editoptions:{value:"<?php echo $this->month_options; ?>"}}, {name:'status', index:'status', width:80, align:'left', editable:true, edittype:"select", editoptions:{value:"Live:Live;Plan:Plan;"}}, {name:'lat', index:'lat', width:140, align:'right', editrules:{required:true}, editable:true}, {name:'lng', index:'lng', width:140, align:'right', editrules:{required:true}, editable:true}, ], height: '300', pager: '#pager-sites', rowNum:30, rowList:[10,30,90], sortname: 'cluster_id', sortorder: 'desc', viewrecords: true, multiselect: false, caption: 'Sites', editurl: '/json/sites' }); $("#sites-grid").jqGrid('navGrid','#pager-sites',{edit:true,add:true,del:true, beforeSubmit : function(postdata, formid) { $.ajax({ url : 'json/validate-site/', data : postdata, dataType : 'json', type : 'post', success : function(data) { alert(data.message); return[data.result, data.message]; } }); }});

  Read the article

• Jquery.get() not returning any data

  - by David Waters

  Hi I am trying to scrape other people web pages (for the forces of good not evil). I am currently trying to do this with javascript/jquery from with in a browser. I am finding that the no data is returned from the jquery.get() success call back function. My code. $.get('http://www.google.co.uk/', function (data, textStatus, XMLHttpRequest){ alert("status " + textStatus); alert('data:' + data); window.data=data; window.textStatus=textStatus; window.httpReq = XMLHttpRequest}); In my mind this should simply do a get on google store the data in window.data and we are all good. What happens is we get textStatus == success and data == "". the status on the XMLHttpRequest is 4(success). I have looked at the network traffic using a transparent proxy (Charles) and everything looks find there http status 200 plenty of data being returned. I am running this just from the Firebug console in Firefox. Any ideas?

  Read the article

• Empty responseText from XMLHttpRequest

  - by PurplePilot

  I have written an XMLHttpRequest which runs fine but returns an empty responseText. The javascript is as follows: var anUrl = "http://api.xxx.com/rates/csv/rates.txt"; var myRequest = new XMLHttpRequest(); callAjax(anUrl); function callAjax(url) { myRequest.open("GET", url, true); myRequest.onreadystatechange = responseAjax; myRequest.setRequestHeader("Cache-Control", "no-cache"); myRequest.send(null); } function responseAjax() { if(myRequest.readyState == 4) { if(myRequest.status == 200) { result = myRequest.responseText; alert(result); alert("we made it"); } else { alert( " An error has occurred: " + myRequest.statusText); } } } The code runs fine. I can walk through and I get the readyState == 4 and a status == 200 but the responseText is always blank. I am getting a log error (in Safari debug) of Error dispatching: getProperties which I cannot seem to find reference to. I have run the code in Safari and Firefox both locally and on a remote server. The URL when put into a browser will return the string and give a status code of 200. I wrote similar code to the same URL in a Mac Widget which runs fine, but the same code in a browser never returns a result.

  Read the article

• ajax redirect dillema, how to get redirect URL OR how to set properties for redirect request

  - by Anthony

  First, I'm working in Google Chrome, if that helps. Here is the behavior: I send an xhr request via jquery to a remote site (this is a chrome Extension, and I've set all of the cross-site settings...): $.ajax({ type: "POST", contentType : "text/xml", url: some_url, data: some_xml, username: user, password: pass, success: function(data,status,xhr){ alert(data); }, error: function(xhr, status, error){ alert(xhr.status); } }); The URL that is being set returns a 302 (this is expected), and Chrome follows the redirect (also expected). The new URL returns a prompt for credentials, which are not being pulled from the original request, so Chrome shows a login dialog. If I put in the original credentials, I get back a response about invalid request sent (it's a valid HTTP request -- 200 -- the remote server just doesn't like one of the headers). When viewing the developer window in Chrome, there are two requests sent. The first is to the original URL with all settings set in the ajax request. The second is to the redirect URL, with a method of "GET", nothing from the "POST" field, and no credentials. I am at a loss as to what I can do. I either need to: Get the redirect URL so I can send a second request (xhr.getResponseHeader("Location") does NOT work), Have the new redirect request preserver the settings from the original request, or Get the final URL that the error came from so I can send another request. Ideally I don't want the user to have to put in their credentials a second time in this dialog box, but I'll take what I can get if I can just get the final URL.

  Read the article

• WCF Ria Services Error : Load operation failed for query 'GetTranslationProgress'

  - by Manoj

  Hello, I am using WCF Ria Services beta in my silverlight application. I have a long running task on the server which keeps writing its status to a database table. I have a "GetTranslationProgress" Ria Service Query method which queries the state to get the status. This query method is called continuously at a regular interval of 5 seconds until a status = Finished or Error is retrieved. In some cases if the task on the server is running for a long duration 2-3 minutes then I receives this error:- Load operation failed for query 'GetTranslationProgress'. The server did not provide a meaningful reply; this might be caused by a contract mismatch, a premature session shutdown or an internal server error. at System.Windows.Ria.OperationBase.Complete(Exception error) at System.Windows.Ria.LoadOperation.Complete(Exception error) at System.Windows.Ria.DomainContext.CompleteLoad(IAsyncResult asyncResult) at System.Windows.Ria.DomainContext.<c_DisplayClass17.b_13(Object ) The error occurs intermittently and I have no idea what could be causing this error. I have checked most of the forums and sites but I have not been able to find out any solution to this issue. Please help.

  Read the article

• Generate JSON object with transactionReceipt

  - by Carlos

  Hi, I've been the past days trying to test my first in-app purchse iphone application. Unfortunately I can't find the way to talk to iTunes server to verify the transactionReceipt. Because it's my first try with this technology I chose to verify the receipt directly from the iPhone instead using server support. But after trying to send the POST request with a JSON onbject created using the JSON api from google code, itunes always returns a strange response (instead the "status = 0" string I wait for). Here's the code that I use to verify the receipt: - (void)recordTransaction:(SKPaymentTransaction *)transaction { NSString *receiptStr = [[NSString alloc] initWithData:transaction.transactionReceipt encoding:NSUTF8StringEncoding]; NSDictionary *jsonDictionary = [NSDictionary dictionaryWithObjectsAndKeys:@"algo mas",@"receipt-data",nil]; NSString *jsonString = [jsonDictionary JSONRepresentation]; NSLog(@"string to send: %@",jsonString); NSLog(@"JSON Created"); urlData = [[NSMutableData data] retain]; //NSURL *sandboxStoreURL = [[NSURL alloc] initWithString:@"https://sandbox.itunes.apple.com/verifyReceipt"]; NSMutableURLRequest *request = [NSMutableURLRequest requestWithURL:[NSURL URLWithString:@"https://sandbox.itunes.apple.com/verifyReceipt"]]; [request setHTTPMethod:@"POST"]; [request setHTTPBody:[jsonString dataUsingEncoding:NSUTF8StringEncoding]]; NSLog(@"will create connection"); [[NSURLConnection alloc] initWithRequest:request delegate:self]; } maybe I'm forgetting something in the request's headers but I think that the problem is in the method I use to create the JSON object. HEre's how the JSON object looks like before I add it to the HTTPBody : string to send: {"receipt-data":"{\n\t\"signature\" = \"AUYMbhY ........... D0gIjEuMCI7Cn0=\";\n\t\"pod\" = \"100\";\n\t\"signing-status\" = \"0\";\n}"} The responses I've got: complete response { exception = "java.lang.IllegalArgumentException: Property list parsing failed while attempting to read unquoted string. No allowable characters were found. At line number: 1, column: 0."; status = 21002; } Thanks a lot for your guidance.

  Read the article

• understanding func<T, TResult> C#

  - by Satish Raj

  Hi I am trying to refactor some of my code to use Func I have created a sample to try to understand how it works but I am getting compilation error. In the e.g. below when I am trying to access the parameter attributes or return the return value the compiler complain. Clarifications please. using System; namespace chsarp { class Program { static void Main(string[] args) { ParamInput input = new ParamInput(); input.ReservationID = 10; Test testMethod = new Test(); Func<ParamInput, ReservationResult> methodToInvoke = testMethod.GetStatus; ReservationResult result = TestFn(methodToInvoke, input); } static Result TestFn<Param, Result>(Func<Param, Result> methodToInvoke, Param parameter) where Result : new() { Result result = new Result(); try { result = methodToInvoke(parameter); } catch (Exception exception) { result.status = string.Format("Error-{0} during reserving {1}", parameter.ReservationID, exception.Message); } return result; } } class Test { public ReservationResult GetStatus(ParamInput msg) { ReservationResult result = new ReservationResult(); result.status = string.Format("The ReservationID-{0}", msg.ReservationID); return result; } } class ParamInput { public int ReservationID { get; set; } } class ReservationResult { public string status { get; set; } } }

  Read the article

• JPA Lookup Hierarchy Mapping

  - by Andy Trujillo

  Given a lookup table: | ID | TYPE | CODE | DESCRIPTION | | 1 | ORDER_STATUS | PENDING | PENDING DISPOSITION | | 2 | ORDER_STATUS | OPEN | AWAITING DISPOSITION | | 3 | OTHER_STATUS | OPEN | USED BY OTHER ENTITY | If I have an entity: @MappedSuperclass @Table(name="LOOKUP") @Inheritance(strategy=InheritanceType.SINGLE_TABLE) @DiscriminatorColumn(name="TYPE", discriminatorType=DiscriminatorType.STRING) public abstract class Lookup { @Id @Column(name="ID") int id; @Column(name="TYPE") String type; @Column(name="CODE") String code; @Column(name="DESC") String description; ... } Then a subclass: @Entity @DiscriminatorValue("ORDER_STATUS") public class OrderStatus extends Lookup { } The expectation is to map it: @Entity @Table(name="ORDERS") public class OrderVO { ... @ManyToOne @JoinColumn(name="STATUS", referencedColumnName="CODE") OrderStatus status; ... } So that the CODE is stored in the database. I expected that if I wrote: OrderVO o = entityManager.find(OrderVO.class, 123); the SQL generated using OpenJPA would look something like: SELECT t0.id, ..., t1.CODE, t1.TYPE, t1.DESC FROM ORDERS t0 LEFT OUTER JOIN LOOKUP t1 ON t0.STATUS = t1.CODE AND t1.TYPE = 'ORDER_STATUS' WHERE t0.ID = ? But the actual SQL that gets generated is missing the AND t1.TYPE = 'ORDER_STATUS' This causes a problem when the CODE is not unique. Is there a way to have the discriminator included on joins or am I doing something wrong here?

  Read the article

• VBS Runtime error code 800A01B6

  - by salvationishere

  I am a newbie to VBS scripting. I am getting above error on line 54, character 5 in script below. This error says "Object doesn't support this property or method: 'MimeMapArray'". And line it is referring to is: MimeMapArray(i) = CreateObject("MimeMap") Can u tell me what I am doing wrong? Here is the script in its entirety. Note, I am trying to run this on an XP OS by double-clicking this VBS file. ' This script adds the necessary Windows Presentation Foundation MIME types ' to an IIS Server. ' To use this script, just double-click or execute it from a command line. ' Running this script multiple times results in multiple entries in the IIS MimeMap. ' Set the MIME types to be added Dim MimeMapObj Dim MimeMapArray Dim WshShell Dim oExec Const ADS_PROPERTY_UPDATE = 2 Dim MimeTypesToAddArray MimeTypesToAddArray = Array(".manifest", "application/manifest", ".xaml", _ "application/xaml+xml", ".application", "application/x-ms-application", _ ".deploy", "application/octet-stream", ".xbap", "application/x-ms-xbap", _ ".xps", "application/vnd.ms-xpsdocument") ' Get the mimemap object Set MimeMapObj = GetObject("IIS://LocalHost/MimeMap") ' Call AddMimeType for every pair of extension/MIME type For counter = 0 to UBound(MimeTypesToAddArray) Step 2 AddMimeType MimeTypesToAddArray(counter), MimeTypesToAddArray(counter+1) Next ' Create a Shell object Set WshShell = CreateObject("WScript.Shell") ' Stop and Start the IIS Service Set oExec = WshShell.Exec("net stop w3svc") Do While oExec.Status = 0 WScript.Sleep 100 Loop Set oExec = WshShell.Exec("net start w3svc") Do While oExec.Status = 0 WScript.Sleep 100 Loop Set oExec = Nothing ' Report status to user WScript.Echo "Windows Presentation Foundation MIME types have been registered." ' AddMimeType Sub Sub AddMimeType(ByVal Ext, ByVal MType) ' Get the mappings from the MimeMap property. MimeMapArray = MimeMapObj.GetEx("MimeMap") ' Add a new mapping. i = UBound(MimeMapArray) + 1 ReDim Preserve MimeMapArray(i) MimeMapArray(i) = CreateObject("MimeMap") MimeMapArray(i).Extension = Ext MimeMapArray(i).MimeType = MType MimeMapObj.PutEx ADS_PROPERTY_UPDATE, "MimeMap", MimeMapArray MimeMapObj.SetInfo() End Sub

  Read the article

< Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >