Search Results

Search found 2911 results on 117 pages for 'payment gateway'.

Page 107/117 | < Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >

• Issues getting a Cisco WLC 5508 to find AIR-LAP1142N

  - by user95917

  hoping someone can help me with a problem here. I'm attempting to setup a test (loan from Cisco) wireless network. Here's what i've got/done: 5508 Controller - Service Port IP set to 10.74.5.2 /24. Management IP set to 10.74.6.2 /24 with a default gateway of 10.74.6.1. Virtual IP set to 1.1.1.1. Copper SFP in slot 7, CAT5 (known good) going from there to port 1/0/47 on the switch. Green lights on both ends. 2960-S Switch - Vlan1 - 10.74.6.1 /24. dhcp pool 10.74.6.0 /24, default router 10.74.6.1. excluded-address 10.74.6.1, 10.74.6.2. 1/0/4 on the switch is set to switchport mode access and no shut. 1/0/47 on the switch is setup to switchport mode trunk and no shut. 1/0/4 has a CAT5 (known good) cable going from there to the AP. When I do a sh cdp nei from the switch, i can see the AP and Controller listed. When i configure my PC's nic to 10.74.5.5, and plug a cable from my nic to the SP port on the controller i can get on the device via the gui. In there, the only errors/info that show up in the trap are: Link Up: Slot: 0 Port: 7 Controller time base status - Controller is out of sync with the central timebase. I've manually set the time but apparently that's not quite the problem (or at least not the entire problem). When i plug the AP in, i see on the switch console that it grants it power, it sees it connect...but the controller won't see it for some reason. From what i've read you shouldn't have to do anything to the AP as it's managed by the controller...but i'm not sure what setting I'm missing for it to work. The AP light on top is continually cycling green, red, yellow. When I first start it up, it blinks green for 20 or so seconds, then goes to solid green for another 20 seconds or so, then flashes blue, green, red for awhile...but always ends up goinn back to the standard, green, red, yellow. Does anyone see any obvious issues with my setup or have any suggestions as to why i might be having a problem? Thanks for your help!

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• Splitting an internet connection between multiple separate subnetworks

  - by pythonian4000

  Problem I have an internet connection that I want to split between four separate networks. My requirements are: I need to be able to monitor the amount of bandwidth and data being used by each network, and notify or control as necessary. The four networks should only be able to connect to the internet, not each other. My parents need to be able to operate it, so it needs a simple, preferably Windows-based GUI. Progress so far Server I have a mini-ITX server with six Gigabit ethernet ports - one for the ethernet internet connection, one for each of the four networks, and one for remote access to the server for administration. Bandwidth control I spent a long time researching solutions here. The majority of the control systems/software I found could control bandwidth usage via QOS, but could not monitor or control the amount of data being used. Eventually I found the SoftPerfect Bandwidth Manager, which has everything I need in terms of monitoring and control - per-interface quota management, usage statistics, a web interface for checking usage, and email notifications when quotas are exceeded. It is also Windows-based and has a simple GUI. Internet sharing This is where I am having issues. I am currently using Windows XP Pro SP2 for the server (yes, I know this is far from ideal, but it's the only spare Windows OS I currently have). I can't use the built-in Internet Connection Sharing for several reasons: The upstream internet router has an IP of 192.168.0.1 which ICS clashes with, and I cannot change the router settings. ICS can only share an internet connection with a single interface, but I have four. I have tried bridging the four network cards, but then the Bandwidth Manager cannot see the four individual interfaces - it only sees the bridge. I have tried setting up Dual DHCP DNS server (and am having issues getting DHCP offers to be received by clients), but that would still require gateway software of some sort, which I have been unable to find. My current attempt is to use OpenVPN, with a server for the internet NIC and a separate client for each of the four networks. My thought is that I could bridge the OpenVPN TAP devices to each NIC, meaning that the Bandwidth Manager would control traffic from the bridge instead of the interface. I have not made much progress here though - I've never used OpenVPN before. Questions Is there a Windows software package that does everything I need? (Unlikely, I know) Is there a Windows software package that will share internet between multiple NICs without bridging? Are either of my about attempts feasible? Would it help to have a newer/server version of Windows? Is there a non-Windows alternative that is easy to use?

  Read the article

• Static IPv6 address in Windows unused for outgoing connections

  - by Luc

  I'm running a Windows server and trying to get it to use a static IPv6 address for outgoing connections to other IPv6 hosts (such as Gmail). I need this because Gmail requires a ptr record, and I can't set one for random addresses. The static address is configured on the host, but it also has a temporary privacy address as well as a random address from the router it seems. By default Windows uses the privacy address; it seems this is the expected behavior (and it makes perfect sense for people/users that did not set a static address, but I did!). I've tried disabling the privacy address with: netsh int ipv6 set privacy disabled This indeed gets rid of the privacy address, but I still have the random address that the router assigned. To disable this, it was said I needed to disable "router discovery" using this command: net interface ipv6 set interface 14 routerdiscovery=disabled Upon doing this, all IPv6 connectivity is lost. If I do this while pinging Gmail, it will report "Destination host unreachable" as soon as I enter the command. In the static IPv6 configuration, I did configure the default gateway and prefix length, so I don't see why it's unable to connect. Probably has something to do with the lack of ARP in IPv6 and somehow being unable to resolve the router's MAC, but I wouldn't know how to fix this. Finally I've tried disabling the DHCPv6 lease with these commands: netsh interface ipv6 set interface "IDMZ Team" managedaddress=disabled netsh interface ipv6 set interface "IDMZ Team" otherstateful=disabled Which was to no avail; the host continues to obtain and use the router-assigned IPv6 address. The router is a FritzBox 7340, which shows me all the IPv4 and IPv6 addresses that the host (identified by MAC) utilizes, but I'm unable to change the assigned address. Maybe this could be done over the telnet interface of the router somehow, but again, I wouldn't know how to do this even if it's the way to go. In short, any of the following would probably solve my problem: Change Windows' source address selection behavior. Have Windows not get an address from the router and not generate a privacy address; Have the router hand out a static address and make Windows use that as source address. Recover connectivity after disabling router discovery on Windows. Alternatively I might use some (batch, perl, ...) script to throw away all IPv6 addresses except the desired one, but this feels rather hacky. If it's the only way (or less hacky than another hacky solution), it might be an option though. Thanks!

  Read the article

• Stop squid caching 302 and 307 with deny_info

  - by 0xception

  TLDR: 302, 307 and Error pages are being cached. Need to force a refresh of the content. Long version: I've setup a very minimal squid instance running on a gateway which shouldn't not cache ANYTHING but needs to be solely used as a domain based web filter. I'm using another application which redirects un-authenticated users to the proxy which then uses the deny_info option redirects any non-whitelisted request to the login page. After the user has authenticated the firewall rule gets placed so they no longer get sent to the proxy. The problem is that when a user hits a website (xkcd.com) they are unauthenticated so they get redirected via the firewall: iptables -A unknown-user -t nat -p tcp --dport 80 -j REDIRECT --to-port 39135 to the proxy at this point squid redirects the user to the login page using a 302 (i've also tried 307, and i've also make sure the headers are set to no-cache and/or no-store for Cache-Control and Pragma). Then when the user logs into the system they get firewall rule which no longer directs them to the squid proxy. But if they go to xkcd.com again they will have the original redirection page cached and will once again get the login page. Any idea how to force these redirects to NOT be cached by the browser? Perhaps this is a problem w/ the browsers and not squid, but not sure how to get around it. Full squid config below. # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 acl localnet src 192.168.182.0/23 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl https port 443 acl http port 80 acl CONNECT method CONNECT # # Disable Cache # cache deny all via off negative_ttl 0 seconds refresh_all_ims on #error_default_language en # Allow manager access only from localhost http_access allow manager localhost http_access deny manager # Deny access to anything other then http http_access deny !http # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !https visible_hostname gate.ovatn.net # Disable memory pooling memory_pools off # Never use neigh cache objects for cgi-bin scripts hierarchy_stoplist cgi-bin ? # # URL rewrite Test Settings # #acl whitelist dstdomain "/etc/squid/domains-pre.lst" #url_rewrite_program /usr/lib/squid/redirector #url_rewrite_access allow !whitelist #url_rewrite_children 5 startup=0 idle=1 concurrency=0 #http_access allow all # # Deny Info Error Test # acl whitelist dstdomain "/etc/squid/domains-pre.lst" deny_info http://login.domain.com/ whitelist #deny_info ERR_ACCESS_DENIED whitelist http_access deny !whitelist http_access allow whitelist http_port 39135 transparent ## Debug Values access_log /var/log/squid/access-pre.log cache_log /var/log/squid/cache-pre.log # Production Values #access_log /dev/null #cache_log /dev/null # Set PID file pid_filename /var/run/gatekeeper-pre.pid SOLUTION: I believe I might have found a solution to this. After days and days trying to figure it out, only through a random stumble I found client_persistent_connections off server_persistent_connections off This did the trick. So it wasn't so much cache as it was a single persistent connection messing things up. W000T!

  Read the article

• Tutorial for configuring OpenVPN [on hold]

  - by user2699451

  I have been through 10+ tutorials on setting up a OpenVPN, and each tutorial gives a different problem... Does anyone know of a decent and helpful website/tutorial which I could go to to get it set up? I have been battling through it for almost 2 months now. Yes, I have also bugged forums.openvpn, but I think I have "reached my post limit" with them. I have to configure it remotely via ssh. UPDATE: okay, I have been asked to be more clear on the topic I followed this tutorial (as a example) - http://www.servermom.com/how-to-build-openvpn-server-on-centos-6-x/732/ I had no issues setting up, etc. except when I boot into windows and run the OpenVPN GUI Client, it connects and gives this error: WARNING: Bad encapsulated packet length from peer (21331), which must be 0 and <= 1576 -- please ensure that --tun-mtu or --link-mtu is equal on both peers -- this condition could also indicate a possible active attack on the TCP link -- [Attemping restart...] Here is my server config: port 1194 #- port proto udp #- protocol dev tun tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 reneg-sec 0 ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem plugin /usr/lib64/openvpn/plugin/lib/openvpn-auth-pam.so /etc/pam.d/login #- Co$ #plugin /etc/openvpn/radiusplugin.so /etc/openvpn/radiusplugin.cnf #- Uncomment$ client-cert-not-required username-as-common-name server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" keepalive 5 30 comp-lzo persist-key persist-tun status 1194.log verb 3 and my client config: client dev tun proto udp remote [server ip] 1194 # - Your server IP and OpenVPN Port resolv-retry infinite nobind tun-mtu 1500 tun-mtu-extra 32 mssfix 1450 persist-key persist-tun ca ca.crt auth-user-pass comp-lzo reneg-sec 0 verb 3 OpenVPN Client Log: Thu Oct 31 11:51:29 2013 OpenVPN 2.0.9 Win32-MinGW [SSL] [LZO] built on Oct 1 2006 Thu Oct 31 11:51:44 2013 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Thu Oct 31 11:51:44 2013 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Thu Oct 31 11:51:44 2013 LZO compression initialized Thu Oct 31 11:51:44 2013 Control Channel MTU parms [ L:1576 D:140 EF:40 EB:0 ET:0 EL:0 ] Thu Oct 31 11:51:44 2013 Data Channel MTU parms [ L:1576 D:1450 EF:44 EB:135 ET:32 EL:0 AF:3/1 ] Thu Oct 31 11:51:44 2013 Local Options hash (VER=V4): '2547efd2' Thu Oct 31 11:51:44 2013 Expected Remote Options hash (VER=V4): '77cf0943' Thu Oct 31 11:51:44 2013 Attempting to establish TCP connection with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCP connection established with x.x.x.x:1194 Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link local: [undef] Thu Oct 31 11:51:44 2013 TCPv4_CLIENT link remote: x.x.x.x:1194 // after this it just hangs, nothing happens So I dont know what I am doing wrong but I am getting a bit impatient and on each forum I post this, I get stupid/unrelated/unhelpful answers...

  Read the article

• VPN - force a selective range of ip to run on VPN (linux)

  - by Francesco

  Preface: I know there are similar question here and there however I'm a kind of newbie on Net stuff so I need an answer on this specific scenario, hoping that can help others too as it is a common problem Let say I cannot do anything on the local switch to change the local ip range, I don't want to use any complicate trick as use VMachine to hide the local ip range but I want to use net tools to solve the issue. Scenario my local net assign me an IP of this class 192.168.1.xxx (ex. 192.168.1.116) and my VPN (VPNC) assign me IP of same class 192.168.1.xxx (ex. 192.168.1.247) Obviously I need VPN to access local address (ex. 192.168.1.100) but when I open any address of the class 192.168.1.xx the route point to my local net and not to the VPN ones. I'm on linux and i'd like gui solution (network manager) in case it is not possible let play with route command. here what network manager offer me: Here my actual route once connected to the VPN: Here some route information (route -n) Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 9 0 0 wlan0 192.168.1.246 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 Here my ifconfig : ppp0 Link encap:Point-to-Point Protocol inet addr:192.168.1.247 P-t-P:192.168.1.246 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:3415 errors:0 dropped:0 overruns:0 frame:0 TX packets:2525 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:3682328 (3.6 MB) TX bytes:402315 (402.3 KB) wlan0 Link encap:Ethernet HWaddr 4c:eb:42:06:a3:a6 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4eeb:42ff:fe06:a3a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72598 errors:0 dropped:0 overruns:0 frame:0 TX packets:42300 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76000532 (76.0 MB) TX bytes:13919400 (13.9 MB) The Question So basically I would like to add a rule to force this particular address (192.168.1.100) on the VPN and not on my local net

  Read the article

• Using OpenVPN, yet netflix.com blocks access

  - by user837848

  I have set up an OpenVPN server on a VPS in the USA and configured it to route all clients traffic through it. Everything seems to work fine regarding the VPN connection in gerneral. All ip lookup sites show me the us server's ip address and even hulu.com works(it won't work if you are not in the usa). But for some reason netflix.com says "Sorry, Netflix is not available in your country yet.". So I thought that netflix probably uses some more sophisticated ways to determine your location beyond just your ip address. But I could not find a way to get it to work until I dropped the idea of using a VPN and instead connected to the server via a simple socks tunnel with ssh by running: ssh -D 9999 user@serverip All I had to do was changing the key network.proxy.socks_remote_dns in Firefox from false to true to prevent DNS leaks and setting up the socks proxy. Then I could finally watch netflix.com. As a result I concluded that there is nothing in the browser(or something like system timezone) that tells netflix the location, so it has to have something to do with the OpenVPN config. After that I used tcpdump to log all the traffic on the server's network interface venet0 (OpenVZ VPS), visited netflix.com on the client while first connected to the VPN and then connected via socks tunnel and afterwards compared both outputs. The only thing that caught my eye was that while using the socks tunnel the server mainly used ipv6 to connect to netflix whereas it only used ipv4 when the client was connected to the OpenVPN server. But I don't get how that could make such a difference. So what am I missing? Is there a way to configure OpenVPN to also use ipv6 to connect to a website although there is only an ipv4 connection between the VPS and the client? Here is the server.conf of the OpenVPN server (OpenVZ VPS) local serverip port 443 proto tcp dev tun ca ./easy-rsa2/keys/ca.crt cert ./easy-rsa2/keys/vps1.crt key ./easy-rsa2/keys/vps1.key # This file should be kept secret dh ./easy-rsa2/keys/dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" client-to-client keepalive 10 120 tls-auth ta.key 0 # This file is secret cipher AES-256-CBC comp-lzo max-clients 4 user nobody group nogroup persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 3 iptables forwarding iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j SNAT --to-source serverip (enabled ipv4 forwarding) I have tried everything always on a Win7 and a Debian client with only ipv4 connections and always made sure that they use the correct DNS server (tested with ipleak.net and tcpdump / wireshark). client.conf: client dev tun proto tcp remote serverip 443 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 cipher AES-256-CBC comb-lzo verb 3

  Read the article

• getting Internet connection sharing working in a slightly more complicated configuration

  - by tirichitirca t

  I have the following configuration: Computer A - Mac OSX 10.8.4, wireless & wired adapters Computer B - Windows 7 (64 bit), wireless & wired adapters, has internet connection via the wired adapter (ethernet) d-link wired/wireless router. Problem to solve: Connect from computer A to the internet through the wired connection of computer B. I tried the following: I set up a local network between A and B using the d-link router. The configuration is this: D-link router - 192.168.0.1 A - wired connection to the d-link router, static 192.168.0.101 (I could have used the wireless but I preferred the wired connection) B - wireless connection to the d-link router DHCP 192.168.0.102 (but I made sure it always gets the same address) B - wired connection to the internet using some address that begins with 10.x.y.z. In this configuration A can see B. I enabled ICS on the wired adapter of B. I set up the Gateway of A to point to B and DNS servers to point to the DNS servers specified for the 10.x.y.z address. It doesn't work, A goes only as far as B. It can ping the 10.x.y.z address of B though. I then found this article: http://terrybritton.com/windows-internet-connection-sharing-ics-not-working-with-linux-bridging-is-the-solution-916/. Terry is suggesting that a bridge should be defined on B between the two connections. I tried that but basically computer B is screwed as soon as I create the bridge. It can't connect to the internet anymore. It is as if the network bridge seems to think the traffic to the internet should go from the wired connection to the wireless and not the other way around. The other thing that puzzles me is the router itself. In general the router needs an internet address. In a normal configuration it is the router that gets the ip address and the internet traffic goes through the router. In my case I am not interested in that. So, any suggestions to get this working? I wouldn't shy away from using a commercial software but I would think windows 7 should allow me to do it. Thanks

  Read the article

• MySQL Execution Time Spikes

  - by Brett

  I am having issues with MySQL all of the sudden today. Details: OS: CentOS release 5.7 Server type: Parallels virtuozzo container running on mediatemple DV 4.0 package Average total memory usage: <500mb Total memory usage allowed: 1gb (part of shared pool for emergency only, users are only guaranteed 500mb) Processor: 1ghz Main database sizes with most usage: 275mb & 107mb server stack: nginx 1.0.10, mysql 5.1.54, php 5.3.8 with php-fpm innodb_buffer_pool_size=100M php-fpm max children: 5 Webapps: custom php-based sites, magento & drupal slow query timeout is set to 1 second Steps I completed towards diagnosis: Cannot restart container yet - I will try later tonight when our domestic traffic has dropped Enabled mysql and php-fpm slowlog. Found functions that did DB queries in php-fpm slowlog were taking over 1s to complete at times Found some simple queries in mysql slowlog taking well over 1s to complete that should take less than 1s. Most interesting - execution time seems to spike at times. A query will take .2s a couple times, then one time it will take 8s to run the same query. These results were verified by running raw SQL queries through mysql command line. Top does not reveal anything too interesting Only resource related thing i can see is load averages much higher than normal Up until today, mysql has been fine, there have been no major changes to the db since yesterday. Sometimes things are so bad, I am seeing bad gateway errors after 60s of execution time. Innodb is doing on average 300-1400 reads/sec. Mysql is doing 3-10 queries/sec slow query count in 2 hours uptime is 171 (with slow timeout at 1 second) Tried restarting mysql, nginx, php-fpm multiple times For example: UPDATE `catalogsearch_query` SET `query_text` = 'EW 90', `num_results` = '7532', `popularity` = '99180', `redirect` = NULL, `synonym_for` = NULL, `store_id` = '1', `display_in_terms` = '1', `is_active` = '1', `is_processed` = '1', `updated_at` = '2012-05-08 21:38:31' WHERE (query_id='31'); This query took 17sec to complete one time, rest of the time around .079 sec. But varies, sometimes 1sec, sometimes .004 sec. This is running the same query, over and over with a couple seconds time in between each. Most tables are innodb, and sometimes I noticed the lock time taking 90% of the query execution time, but most of the time lock time is insignificant. Any idea what's going on here?

  Read the article

• WSS and CAG , _layout pages break

  - by Mike

  Alright, I've searched everywhere and I cannot find the answer, due to the rarity of our setup. WSS 3.0/IIS 6.0/WinServer 2003 We have a sharepoint site that is in good shape, almost. Its TCP and SSL port are uncommon and need to be rerouted to work properly. This is where the Citrix Access Gateway (CAG) comes in play. It will redirect any request from URL (something.something.com) to the correct SSL port on the correct server. My AAM is configured to Default something.something.com and nothing else, since the CAG will provide the port. We use FBA, and require SSL. This works perfectly for everything that is safe or that is anything that an end user can see, but if I try to add a webpart, it errors out. Whereas if I add it internally, or bypass the CAG the webpart adds fine. The same goes for most of the _layouts pages, like _layouts/new.aspx. If I add a Link List/Doc library on the something.something.com, it errors out (Page cannot be displayed) and the page won't display, but if I try it with an internal address it will work fine. I found that if I am trying to add something or doing anything administrative, the site will navigate to the pages that I need to go to fine, but when i actually ADD something the URL will change from something.something.com to something.something.com:SSLport, thus erroring out the site. The URL with the SSL port shows on the Site URL when navigating to Site Settings. However, if I bypass the CAG, using the internal address the _layouts page works like a charm and i can add anything. All the CAG does is reroute a DNS request to the provided server and port. I've tried reextending the application, no luck same thing. I've tried changing the AAM to hide the port and the CAG rejects it. I've tried to recreate a new webapp/site collection with the same rules on the CAG, same thing occurs. Correct me if I'm wrong, and please provide me with some feedback and answers. Any suggestions would be very appreciated. Is it the CAG or the Alternate Access Mappings (AAM)?

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• WinXP - Having trouble sharing internet with 3G USB modem via ICS

  - by Carlos Nunez

  all! I've been banging my head against a wall with this issue for a few days now and am hoping someone can help out. I recently signed up for T-Mobile's webConnect 3G/4G service to replace the faltering (and slow) DSL connection in my apartment. The goal was to put the SIM in one of my old phones and use its built-in WLAN tethering feature to share Internet out to rest of my computers. I quickly found out that webConnect-provisioned SIMs do not work with regular smartphones, so I was forced to either buy a 4G-compatible router or tether one of my old laptops to my wireless router and share out that way. I chose the latter, and it's sharpening my inner masochistic self by the day. Here's the setup: GSM USB modem (via hub), ICS host - 10/100 Mbps Ethernet NIC, ICS "guest" - WAN port of my SMC WGBR14N wireless router in bridged mode (i.e. wireless access point). Ideally, this would make my laptop the DHCP server and internet gateway with the WAP giving everyone wireless coverage. I can browse internet on the host laptop fine. However, when clients try to connect, they get a DHCP-assigned IP from the laptop and are able to use the Internet for a few minutes before completely dying. After that happens, they are able to re-associate with the WAP and get IP addresses, but are unable to use Internet or resolve IP addresses until the laptop and router are restarted. If they do get access, it's very, very slow. After running Wireshark on the host machine, it turns out that this is because every TCP connection keeps getting RST. DNS seems to work. I would normally think the firewall is the culprit here, but when it drops packets, it drops them completely. The fact that TCP connections are being ACK'ed by the destination rules that out. Of course, none of the event Log isn't saying anything about what's going on. I also tried disabling power management on the NIC, since that's caused problems in the past; that didn't help either. I finally disabled receive-side scaling as per a Microsoft KB (that applied to Windows Server 2003, SP2) to no avail. I'm thinking of trying it with a different NIC (will be tough; don't have a spare Ethernet NIC around for the laptop), but I'm getting the impression that this simply doesn't work. Can anyone please advise? I apologise for the length of this post; all contributions are much appreciated! -Carlos.

  Read the article

• Accessing guests on virtual network when connected to host via PPTP

  - by Viktor Elofsson

  I'm setting up a development machine which runs Ubuntu 12.04 and KVM for virtualization. I have a guest running Ubuntu 12.04 which can be accessed from the host via its IP address which is assigned by libvirt. The guest can also access the internet, no problem there. However, now I want to setup PPTP so I can connect to the host (from my workstation running Windows 7) and directly access guests without relying on SSH port forwarding. I can connect from my W7-machine to the host (PPTP), but I cannot access any virtual machines (which are accessable from the host directly). Relevant configuration files cat /etc/network/interfaces auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address x.x.x.x broadcast x.x.x.x netmask x.x.x.x gateway x.x.x.x # default route to access subnet up route add -net x.x.x.x netmask x.x.x.x gw x.x.x.x eth0 virsh net-edit default <network> <name>default</name> <uuid>xxxxxxxx-72ce-3c20-af0f-d3a010f1bef0</uuid> <forward mode='nat'/> <bridge name='virbr0' stp='on' delay='0' /> <mac address='52:54:00:xx:xx:xx'/> <ip address='192.168.122.1' netmask='255.255.255.0'> <dhcp> <range start='192.168.122.2' end='192.168.122.254' /> <host mac='52:54:00:yy:yy:yy' name='web1' ip='192.168.122.11' /> </dhcp> </ip> </network> cat /etc/pptpd.conf (commented lines removed) # TAG: option # Specifies the location of the PPP options file. # By default PPP looks in '/etc/ppp/options' # option /etc/ppp/pptpd-options # TAG: logwtmp # Use wtmp(5) to record client connections and disconnections. # logwtmp #(Recommended) localip 192.168.122.1 remoteip 192.168.122.234-238,192.168.122.245 cat /etc/ppp/chap-secrets* # Secrets for authentication using CHAP # client server secret IP addresses xxxxx * yyyyyyyyyy 192.168.122.100 I get the correct IP address when connecting my W7-machine, but when I try to ping the virtual machine at 192.168.122.11 I get Reply from 192.168.122.1: Destination port unreachable. It's probably something trivial I'm missing but I can't for the life of me figure out what it is. So I'm turning to you, serverfault.

  Read the article

• ubuntu eth0 not reconnecting after cable unplugged

  - by Alex

  I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

  Read the article

• How to add IP range to a server?

  - by Efe Cakinberk

  Hello, First of all I must say that I'm ver inexperienced server and network user. But I rented a unmanaged dedicated server. Well I didn't know what unmanaged really means, then I learned it when I needed support. Well I must do everything by myself. I have a problem. I had already 4 IPs on my server when I rented it. But then I needed more Ips and my server assigned me 32 Ips in which I can only use 27 of them. 85.25.230.0 - 85.25.230.31 this is my Ip range and they say the following Ips must not be configured on the server: 85.25.230.0 - network address 85.25.230.1 - gateway address 85.25.230.2 - router redundancy 85.25.230.3 - router redundancy 85.25.230.31 - broadcast address But the problem is ok Ips are assigned to me but they are not setup on my server. How will I setup Ips to work on my server? I did this after my reseach on google: I used this command on command prompt: route add 85.25.230.0 mask 255.255.255.224 85.25.230.1 metric 1 if then it said OK!. and I thought they should be working. (btw, mask is given to me by my ISP and I don't know metric 1 and if means I just saw it on the net and write it here) I setup my domains via using Plesk Kontrol Panel. So i added one domain and setup one of my new Ips 85.25.230.5 to it. But no it is not working. When I visit the domain via browser, there is a Plesk page comes and says this domain is not configured on the server. Then I changed the domains Ip to one of my old Ips which are given to me with the server and which I have been using for my other domains for a long time. Ok in a second, domain started working. I set it back to my new Ip and domain did not work. As I said, I'm not an expert and do not now the logic. But I'm eager to learn. Can you tell me what might couse the problem and did I do wrong while setting up IP RANGE to my server, if so how can I set them up? Thank you, Efe

  Read the article

• nginx crashes on ssl after about a minute

  - by Scott

  Here are my configuration files ssl.conf # HTTPS server # server { listen 443 ssl; server_name api.domain.com; error_log /var/log/nginx/api.error.log; location / { root /var/www/api.domain.com; index index.html index.php index.php; try_files $uri $uri/ /index.php?$args; } ssl on; ssl_certificate /etc/nginx/api.domain.com.crt; ssl_certificate_key /etc/nginx/api.domain.com.key; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers HIGH:!aNULL:!MD5; ssl_prefer_server_ciphers on; # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 location ~ \.php$ { # root html; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_split_path_info ^(.+\.php)(.*)$; fastcgi_param SCRIPT_FILENAME /var/www/api.domain.com$fastcgi_script_name; fastcgi_param HTTPS on; include fastcgi_params; } location ~ /\.ht { deny all; } } nginx.conf user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; gzip on; include /etc/nginx/conf.d/*.conf; } I have a server running on port 80 that runs with no issues. As soon as I turn on this api server running on ssl, it works for about a minute and then crashes and gives a 504 Gateway Time-out. Running nginx/1.2.3

  Read the article

• Configuring Windows 2003 As A Router

  - by Sean M

  I am trying to configure a Windows 2003 server to act as a router, so that the two subnetworks that I'm dealing with can communicate with one another without NAT. I am mostly sure that I have configured Windows 2003 incorrectly, and I'm finding it very difficult to drill down through Google results to something helpful. I have a 192.168.1.0/24 network that is my "production" network (in the sense that I'm in trouble if I screw it up) and a 10.0.0.0/8 network that is my test network. The 192.168.1.0 network is ruled by a gateway whose routing table looks like this (my address redacted): The Windows 2003 server, "prime," is multihomed. Its network adapters are at 192.168.1.122, (as seen above), 10.0.0.1, and 10.0.0.2. I added the Routing and Remote Access role to it, and enabled LAN routing. I do not have it using RIP or other routing protocols. Its current routing table is shown below. To me, it looks like all of the right routes are there for traffic to pass between the 192.168.1.0 network and the 10.0.0.0 network. However, traffic does not pass. The 10.0.0.11 and .12 clients cannot be contacted from the 192.168.1.0 network. When I use traceroute to try to get to them, the trace gets to the Windows 2003 server's 192.168.1.122 address, then produces nothing but "* * *" timeouts. When I try to traceroute to 192.168.1.1 from a 10.0.0.0-network client, I get "destination host unreachable." However, I know that the routing is working at least a little, because from the 192.168.1.0 network, I can connect to the Windows server just fine by referring to it as 10.0.0.1. What static routes would allow me to contact 10.0.0.11 and .12 from the 192.168.1.0 network? Is it possible to tell the Windows server "since you are a DHCP/DNS server, you already know routes to get to machines that are getting IP addresses from you, please add those to your routing table" ? Will using RIP or OSPF on the Windows server actually be helpful in this situation?

  Read the article

• iCloud stuff stops working while connected to OpenVPN [closed]

  - by Taco Bob

  I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again!

  Read the article

• Small Business Server services will not start, and remote desktop and UAC are broken

  - by Stephen Jennings

  Yesterday I began setting up a server with Windows Small Business Server 2008. All I am configuring it for right now is to be a domain controller and Exchange server. I completed the initial setup of SBS then started looking through different connection options (allowing VPN versus using a TS Gateway). After I rebooted one time, I started having three not-obviously-related issues: First, I could no longer remote desktop into the computer. I ran TCPView and saw that it was no longer listening on port 3389. I checked everything in Terminal Service Configuration but everything shows the computer ought to be allowing connections. Also, when I tried to use anything that required user account control elevation, the UAC dialog never popped up and the program that was waiting just froze. If I try to run "regedit" from the Run box, for example, it never appears. When I run in safe mode which does not run with UAC, I was able to access everything. I didn't want to deal with it, so I turned off UAC and rebooted. Finally, in the Windows SBS Console, there are status indicators for Security, Updates, Backup, and Other Alerts. The first three get stuck saying "Querying". Looking in the computer alerts, I have events showing the following services stopped: Background Intelligent Transfer Service KtmRm for Distributed Transaction Coordinator Distributed Transaction Coordinator Microsoft Exchange Information Store Microsoft Exchange System Attendant Microsoft Exchange Transport Windows Remote Management Update Services Windows Update I figured I must have configured something wrong accidentally and I couldn't find anything using Google explaining what might be the case, so I just decided to format the hard drive and reinstall SBS from scratch. I did this and everything was working last night, but I just turned the machine back on and it is doing the same thing again! On my second install, I did not configure anything except the following (all from SBS Console): Connect to the Internet (set IP and router address) Turn off customer feedback. Set up internet address. Decline to use a Smart Host for email. Added one standard user account. Since this happened again and I was very careful the second time not to configure anything outside of the SBS Console, I feel like there's something else going on. Right now the machine is on an isolated network that does have internet access. My desktop is the only other machine plugged into this network. Any and all help is appreciated (before I tear my hair out!)

  Read the article

• Trouble joining Windows Server 2008 to Domain

  - by Jim R

  When I try to join my new server to my existing domain I get the following error: "An attempt to resolve the DNS name of a DC in the domain being joined has failed. Please verify this client is configured to reach a DNS server that can resove DNS names in the target domain." I have tried all of the following already: Successfully pinged the domain controller. Ping the new server from the domain controller by IP address and by DNS name. Ping the DC server from the new server by IP address and by DNS name. Changed the network to DHCP (it was originally static). No joy as static or DHCP. Turned off all firewall settings. Added the domain name to 'hosts' file. Added the server name of the primary domain controller to the 'hosts' file in the new server. Any ideas? Thanks in advance for any help! Jim Update: With help from J. Brian Kelly (Thanks) I have managed to narrow down the problem to a DNS issue. Specifically, UDP/53 packets are being sent (they are seen in Network Monitor), but are not getting to the DNS server. But, I do not yet know why. Update: The quested output from IPCONFIG for the HyperV host and the virtual machine. IPCONFIG from HyperV Server Windows IP Configuration Host Name . . . . . . . . . . . . : HYPER Primary Dns Suffix . . . . . . . : sfi-wfc.com Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : sfi-wfc.com Ethernet adapter Local Area Connection 4: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Primary Network Physical Address. . . . . . . . . : 00-30-48-CA-CC-7A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::cd16:3ac2:3d4f:e275%679(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.100.1(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.100.10 DHCPv6 IAID . . . . . . . . . . . : -1476382648 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-10-20-E9-00-30-48-CA-CC-7A DNS Servers . . . . . . . . . . . : 192.168.100.5 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 3: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : sfi Description . . . . . . . . . . . : Intel(R) 82576 Gigabit Dual Port Network Connection #2 Physical Address. . . . . . . . . : 00-30-48-CA-CC-7B DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPCONFIG from Virtual Machine Windows IP Configuration Host Name . . . . . . . . . . . . : DB Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : sfi Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : sfi Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter Physical Address. . . . . . . . . : 00-15-5D-66-03-02 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.100.128(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Saturday, August 29, 2009 10:44:45 AM Lease Expires . . . . . . . . . . : Tuesday, September 01, 2009 3:08:33 PM Default Gateway . . . . . . . . . : 192.168.100.10 DHCP Server . . . . . . . . . . . : 192.168.100.5 DNS Servers . . . . . . . . . . . : 192.168.102.5 Primary WINS Server . . . . . . . : 192.168.100.5 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter Local Area Connection* 8: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : sfi Description . . . . . . . . . . . : isatap.sfi Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 02-00-54-55-4E-01 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes

  Read the article

• HP MSR 30-10a Router - Route Traffic over Default Route

  - by SteadH

  We have a brand new HP MSR 30-10a Router. We have a fairly simple routing situation - we have two IP blocks, one which has a route out. We need things on the first block to go through the router, and out. I have an old Cisco 2801 router doing the job right now. For our example - IP Block 1: 50.203.110.232/29, Router interface on this block is 50.203.110.237, route out is 50.203.110.233. IP Block 2: 50.202.219.1/27, Router interface on this block at 50.202.219.20. I have a static route created for: 0.0.0.0 0.0.0.0 50.203.110.233 The router seems to understand this. When on the CLI via serial cable, I can ping 8.8.8.8 and hear responses from Google DNS. Woo hoo! The issue arrives when any client sits on the IP Block 2 side. I configured my client with a static IP of 50.202.219.15/27, default gateway 50.202.219.20. I can ping myself. I can ping the near side of the router (50.202.219.20), and I can ping the far side of the router (50.203.110.237. I cannot ping anything else in IP block 1, nor can I ping 8.8.8.8. Here is my configuration file: <HP>display current-configuration # version 5.20.106, Release 2507, Standard # sysname HP # domain default enable system # dar p2p signature-file flash:/p2p_default.mtd # port-security enable # undo ip http enable # password-recovery enable # vlan 1 # domain system access-limit disable state active idle-cut disable self-service-url disable # user-group system group-attribute allow-guest # local-user admin password cipher $c$3$40gC1cxf/wIJNa1ufFPJsjKAof+QP5aV authorization-attribute level 3 service-type telnet # cwmp undo cwmp enable # interface Aux0 async mode flow link-protocol ppp # interface Cellular0/0 async mode protocol link-protocol ppp # interface Ethernet0/0 port link-mode route ip address 50.203.110.237 255.255.255.248 # interface Ethernet0/1 port link-mode route ip address 50.202.219.20 255.255.255.224 # interface NULL0 # ip route-static 0.0.0.0 0.0.0.0 50.203.110.233 permanent # load xml-configuration # load tr069-configuration # user-interface tty 12 user-interface aux 0 user-interface vty 0 4 authentication-mode scheme # My guess right now is there is some sort of "permission" needed to use the default route. The manuals haven't turned up a lot in this area that don't make the situation much more complicated (but maybe it needs to be more complicated?) Background: we use HP switches, and I love the CLI. I bought HP thinking the command line interface would be similar, or at least speak the same language. Whoops! I'd be happy to provide more information or perform any additional tests. Thanks in advance! Update 1: The manual mentions routing rules. I hadn't previously added these (since our Cisco 2801 seems to route anything by default). I added: ip ip-prefix 1 permit 0.0.0.0 0 less-equal 32 alas, still no dice.

  Read the article

• Understanding packet flows over RVI

  - by choco-loo

  I'm trying to get a full grasp of firewall filters and how to apply them on a Juniper EX4200 switch - to be able to block ports, police traffic and shape traffic. The network architecture is as follows internet >-< vlan4000 >-< vlan43 vlan4000 is a public "routed" block (where all the IPs are routed to and the internet gw is) vlan43 is a vlan with public IPs with devices (servers) attached There are static routes and RVI's on the EX4200 to send all traffic via vlan4000's gateway to reach the internet. I've set up filters on both input and output of the respective RVI's and VLAN's - with simple counters, to measure traffic flow from a server inside of vlan43 and a server on the internet. Using a combination of iperf for UDP and TCP tests and fping for ICMP tests - I observed the following, icmp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 100 100 unit43-counter-out 0 0 vlan4000-counter-in 6 4 vlan4000-counter-out 107 104 vlan43-counter-in 101 100 vlan43-counter-out 100 100 tcp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 73535 38480 unit43-counter-out 0 0 vlan4000-counter-in 7 8 vlan4000-counter-out 73543 38489 vlan43-counter-in 73535 38481 vlan43-counter-out 38938 75880 udp vlan43>internet internet>vlan43 unit4000-counter-in 0 0 unit4000-counter-out 0 0 unit43-counter-in 81410 1 unit43-counter-out 0 0 vlan4000-counter-in 18 7 vlan4000-counter-out 81429 8 vlan43-counter-in 81411 1 vlan43-counter-out 1 85472 My key goals are to set up a few filters and policers, as there will be many more VLANs - that all need protecting from each other and the internet. Then globally limit/police all outbound traffic to the internet Block inbound ports to vlan43 (eg. 22) Limit outbound traffic from vlan43 (to the internet) Limit outbound traffic from vlan43 (to other vlans) Limit outbound traffic from vlan4000 (to the internet from all vlans) Route traffic from vlans via specific routing instances (FBF) The question What I want to understand is why there isn't ever any activity on unit4000 or vlan4000 inbound or outbound counter - is this because there isn't a device on this VLAN - and that the traffic is only traversing it? And with regards to the TCP test - why is there twice as many packets on unit43-counter-in, vlan4000-counter-out and vlan43-counter-in - is this counting both the inbound and outbound traffic?

  Read the article

• Aliased network interfaces and isc dhcp server

  - by Jonatan

  I have been banging my head on this for a long time now. There are many discussions on the net about this and similar problems, but none of the solutions seems to work for me. I have a Debian server with two ethernet network interfaces. One of them is connected to internet, while the other is connected to my LAN. The LAN network is 10.11.100.0 (netmask 255.255.255.0). We have some custom hardware that use network 10.4.1.0 (netmask 255.255.255.0) and we can't change that. But we need all hosts on 10.11.100.0 to be able to connect to devices on 10.4.1.0. So I added an alias for the LAN network interface so that the Debian server acts as a gateway between 10.11.100.0 and 10.4.1.0. But then the dhcp server stopped working. The log says: No subnet declaration for eth1:0 (no IPv4 addresses). ** Ignoring requests on eth1:0. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** No subnet declaration for eth1:1 (no IPv4 addresses). ** Ignoring requests on eth1:1. If this is not what you want, please write a subnet declaration in your dhcpd.conf file for the network segment to which interface eth1:1 is attached. ** I had another server before, also running Debian but with the older dhcp3 server, and it worked without any problems. I've tried everything I can think of in dhcpd.conf etc, and I've also compared with the working configuration in the old server. The dhcp server need only handle devices on 10.11.100.0. Any hints? Here's all relevant config files: /etc/default/isc-dhcp-server INTERFACES="eth1" /etc/network/interfaces (I've left out eth0, that connects to the Internet, since there is no problem with that.) auto eth1:0 iface eth1:0 inet static address 10.11.100.202 netmask 255.255.255.0 auto eth1:1 iface eth1:1 inet static address 10.4.1.248 netmask 255.255.255.0 /etc/dhcp/dhcpd.conf ddns-update-style none; option domain-name "???.com"; option domain-name-servers ?.?.?.?; default-lease-time 86400; max-lease-time 604800; authorative; subnet 10.11.100.0 netmask 255.255.255.0 { option subnet-mask 255.255.255.0; pool { range 10.11.100.50 10.11.100.99; } option routers 10.11.100.102; } I have tried to add shared-network etc, but didn't manage to get that to work. I get the same error message no matter what...

  Read the article

< Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >