Search Results

Search found 19676 results on 788 pages for 'setup cd'.

Page 107/788 | < Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >

• FreeBSD high load loopback interface

  - by user1740915

  I have a problem with a FreeBSD server. There is a FreeBSD 9.0 amd64, two network cards em1 (internet), em0 (local network) configured firewall ipfw, natd, squid (not transparent), the server acts as a gateway for access to the Internet. Next problem: upload via squid is very low. At this moment I see next: natd, dhcpd load the cpu at that time when uploading through squid and there are a lot of traffic through the loopback interface. ipfw show output 0100 655389684 36707144666 allow ip from any to any via lo0 00200 0 0 deny ip from any to 127.0.0.0/8 00300 0 0 deny ip from 127.0.0.0/8 to any 00400 0 0 deny ip from any to ::1 00500 0 0 deny ip from ::1 to any 00600 4 292 allow ipv6-icmp from :: to ff02::/16 00700 0 0 allow ipv6-icmp from fe80::/10 to fe80::/10 00800 1 76 allow ipv6-icmp from fe80::/10 to ff02::/16 00900 0 0 allow ipv6-icmp from any to any ip6 icmp6types 1 01000 0 0 allow ipv6-icmp from any to any ip6 icmp6types 2,135,136 01100 1615 76160 deny ip from 192.168.1.1 to any in via em1 01200 0 0 deny ip from 199.69.99.11 to any in via em0 01300 46652 3705426 deny ip from any to 172.16.0.0/12 via em1 01400 3936404 345618870 deny ip from any to 192.168.0.0/16 via em1 01500 4 336 deny ip from any to 0.0.0.0/8 via em1 01600 4129 387621 deny ip from any to 169.254.0.0/16 via em1 01700 0 0 deny ip from any to 192.0.2.0/24 via em1 01800 917566 33777571 deny ip from any to 224.0.0.0/4 via em1 01900 147872 22029252 deny ip from any to 240.0.0.0/4 via em1 02000 1132194739 1190981955947 divert 8668 ip4 from any to any via em1 02100 3 248 deny ip from 172.16.0.0/12 to any via em1 02200 35925 2281289 deny ip from 192.168.0.0/16 to any via em1 02300 1808 122494 deny ip from 0.0.0.0/8 to any via em1 02400 3 174 deny ip from 169.254.0.0/16 to any via em1 02500 0 0 deny ip from 192.0.2.0/24 to any via em1 02600 0 0 deny ip from 224.0.0.0/4 to any via em1 02700 0 0 deny ip from 240.0.0.0/4 to any via em1 02800 960156249 1095316736582 allow tcp from any to any established 02900 64236062 8243196577 allow ip from any to any frag 03000 34 1756 allow tcp from any to me dst-port 25 setup 03100 193 11580 allow tcp from any to me dst-port 53 setup 03200 63 4222 allow udp from any to me dst-port 53 03300 64 8350 allow udp from me 53 to any 03400 417 24140 allow tcp from any to me dst-port 80 setup 03500 211 10472 allow ip from any to me dst-port 3389 setup 05300 77 4488 allow ip from any to me dst-port 1723 setup 05400 3 156 allow ip from any to me dst-port 8443 setup 05500 9882 590596 allow tcp from any to me dst-port 22 setup 05600 1 60 allow ip from any to me dst-port 2000 setup 05700 0 0 allow ip from any to me dst-port 2201 setup 07400 4241779 216690096 deny log logamount 1000 ip4 from any to any in via em1 setup proto tcp 07500 21135656 1048824936 allow tcp from any to any setup 07600 474447 35298081 allow udp from me to any dst-port 53 keep-state 07700 532 40612 allow udp from me to any dst-port 123 keep-state 65535 1990638432 1122305322718 allow ip from any to any systat -ifstat when uploading via squid Load Average ||| Interface Traffic Peak Total tun0 in 79.507 KB/s 232.479 KB/s 42.314 GB out 2.022 MB/s 2.424 MB/s 59.662 GB lo0 in 4.450 MB/s 4.450 MB/s 43.723 GB out 4.450 MB/s 4.450 MB/s 43.723 GB em1 in 2.629 MB/s 2.982 MB/s 464.533 GB out 2.493 MB/s 2.875 MB/s 484.673 GB em0 in 240.458 KB/s 296.941 KB/s 442.368 GB out 512.508 KB/s 850.857 KB/s 416.122 GB top output PID USERNAME THR PRI NICE SIZE RES STATE C TIME WCPU COMMAND 66885 root 1 92 0 26672K 2784K CPU3 3 528:43 65.48% natd 9160 dhcpd 1 45 0 31032K 9280K CPU1 1 7:40 32.96% dhcpd 66455 root 1 20 0 18344K 2856K select 1 119:27 1.37% openvpn 16043 squid 1 20 0 44404K 17884K kqread 2 0:22 0.29% squid squid.conf cat /usr/local/etc/squid/squid.conf # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl localnet src 10.0.0.0/8 # RFC1918 possible internal network acl localnet src 172.16.0.0/12 # RFC1918 possible internal network acl localnet src 192.168.0.0/16 # RFC1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localnet http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port 192.168.1.1:3128 # Uncomment and adjust the following to add a disk cache directory. #cache_dir ufs /var/squid/cache 100 16 256 # Leave coredumps in the first cache dir coredump_dir /var/squid/cache I understand that the traffic passes through the SQUID several times. But can not find why.

  Read the article

• Diving into OpenStack Network Architecture - Part 1

  - by Ronen Kofman

  v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} rkofman Normal rkofman 83 3045 2014-05-23T21:11:00Z 2014-05-27T06:58:00Z 3 1883 10739 Oracle Corporation 89 25 12597 12.00 140 Clean Clean false false false false EN-US X-NONE HE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:Arial; mso-bidi-theme-font:minor-bidi; mso-bidi-language:AR-SA;} Before we begin OpenStack networking has very powerful capabilities but at the same time it is quite complicated. In this blog series we will review an existing OpenStack setup using the Oracle OpenStack Tech Preview and explain the different network components through use cases and examples. The goal is to show how the different pieces come together and provide a bigger picture view of the network architecture in OpenStack. This can be very helpful to users making their first steps in OpenStack or anyone wishes to understand how networking works in this environment.  We will go through the basics first and build the examples as we go. According to the recent Icehouse user survey and the one before it, Neutron with Open vSwitch plug-in is the most widely used network setup both in production and in POCs (in terms of number of customers) and so in this blog series we will analyze this specific OpenStack networking setup. As we know there are many options to setup OpenStack networking and while Neturon + Open vSwitch is the most popular setup there is no claim that it is either best or the most efficient option. Neutron + Open vSwitch is an example, one which provides a good starting point for anyone interested in understanding OpenStack networking. Even if you are using different kind of network setup such as different Neutron plug-in or even not using Neutron at all this will still be a good starting point to understand the network architecture in OpenStack. The setup we are using for the examples is the one used in the Oracle OpenStack Tech Preview. Installing it is simple and it would be helpful to have it as reference. In this setup we use eth2 on all servers for VM network, all VM traffic will be flowing through this interface.The Oracle OpenStack Tech Preview is using VLANs for L2 isolation to provide tenant and network isolation. The following diagram shows how we have configured our deployment: This first post is a bit long and will focus on some basic concepts in OpenStack networking. The components we will be discussing are Open vSwitch, network namespaces, Linux bridge and veth pairs. Note that this is not meant to be a comprehensive review of these components, it is meant to describe the component as much as needed to understand OpenStack network architecture. All the components described here can be further explored using other resources. Open vSwitch (OVS) In the Oracle OpenStack Tech Preview OVS is used to connect virtual machines to the physical port (in our case eth2) as shown in the deployment diagram. OVS contains bridges and ports, the OVS bridges are different from the Linux bridge (controlled by the brctl command) which are also used in this setup. To get started let’s view the OVS structure, use the following command: # ovs-vsctl show 7ec51567-ab42-49e8-906d-b854309c9edf     Bridge br-int         Port br-int             Interface br-int type: internal         Port "int-br-eth2"             Interface "int-br-eth2"     Bridge "br-eth2"         Port "br-eth2"             Interface "br-eth2" type: internal         Port "eth2"             Interface "eth2"         Port "phy-br-eth2"             Interface "phy-br-eth2" ovs_version: "1.11.0" We see a standard post deployment OVS on a compute node with two bridges and several ports hanging off of each of them. The example above is a compute node without any VMs, we can see that the physical port eth2 is connected to a bridge called “br-eth2”. We also see two ports "int-br-eth2" and "phy-br-eth2" which are actually a veth pair and form virtual wire between the two bridges, veth pairs are discussed later in this post. When a virtual machine is created a port is created on one the br-int bridge and this port is eventually connected to the virtual machine (we will discuss the exact connectivity later in the series). Here is how OVS looks after a VM was launched: # ovs-vsctl show efd98c87-dc62-422d-8f73-a68c2a14e73d     Bridge br-int         Port "int-br-eth2"             Interface "int-br-eth2"         Port br-int             Interface br-int type: internal         Port "qvocb64ea96-9f" tag: 1             Interface "qvocb64ea96-9f"     Bridge "br-eth2"         Port "phy-br-eth2"             Interface "phy-br-eth2"         Port "br-eth2"             Interface "br-eth2" type: internal         Port "eth2"             Interface "eth2" ovs_version: "1.11.0" Bridge "br-int" now has a new port "qvocb64ea96-9f" which connects to the VM and tagged with VLAN 1. Every VM which will be launched will add a port on the “br-int” bridge for every network interface the VM has. Another useful command on OVS is dump-flows for example: # ovs-ofctl dump-flows br-int NXST_FLOW reply (xid=0x4): cookie=0x0, duration=735.544s, table=0, n_packets=70, n_bytes=9976, idle_age=17, priority=3,in_port=1,dl_vlan=1000 actions=mod_vlan_vid:1,NORMAL cookie=0x0, duration=76679.786s, table=0, n_packets=0, n_bytes=0, idle_age=65534, hard_age=65534, priority=2,in_port=1 actions=drop cookie=0x0, duration=76681.36s, table=0, n_packets=68, n_bytes=7950, idle_age=17, hard_age=65534, priority=1 actions=NORMAL As we see the port which is connected to the VM has the VLAN tag 1. However the port on the VM network (eth2) will be using tag 1000. OVS is modifying the vlan as the packet flow from the VM to the physical interface. In OpenStack the Open vSwitch agent takes care of programming the flows in Open vSwitch so the users do not have to deal with this at all. If you wish to learn more about how to program the Open vSwitch you can read more about it at http://openvswitch.org looking at the documentation describing the ovs-ofctl command. Network Namespaces (netns) Network namespaces is a very cool Linux feature can be used for many purposes and is heavily used in OpenStack networking. Network namespaces are isolated containers which can hold a network configuration and is not seen from outside of the namespace. A network namespace can be used to encapsulate specific network functionality or provide a network service in isolation as well as simply help to organize a complicated network setup. Using the Oracle OpenStack Tech Preview we are using the latest Unbreakable Enterprise Kernel R3 (UEK3), this kernel provides a complete support for netns. Let's see how namespaces work through couple of examples to control network namespaces we use the ip netns command: Defining a new namespace: # ip netns add my-ns # ip netns list my-ns As mentioned the namespace is an isolated container, we can perform all the normal actions in the namespace context using the exec command for example running the ifconfig command: # ip netns exec my-ns ifconfig -a lo        Link encap:Local Loopback           LOOPBACK  MTU:16436 Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b) We can run every command in the namespace context, this is especially useful for debug using tcpdump command, we can ping or ssh or define iptables all within the namespace. Connecting the namespace to the outside world: There are various ways to connect into a namespaces and between namespaces we will focus on how this is done in OpenStack. OpenStack uses a combination of Open vSwitch and network namespaces. OVS defines the interfaces and then we can add those interfaces to namespace. So first let's add a bridge to OVS: # ovs-vsctl add-br my-bridge Now let's add a port on the OVS and make it internal: # ovs-vsctl add-port my-bridge my-port # ovs-vsctl set Interface my-port type=internal And let's connect it into the namespace: # ip link set my-port netns my-ns Looking inside the namespace: # ip netns exec my-ns ifconfig -a lo        Link encap:Local Loopback           LOOPBACK  MTU:65536 Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b) my-port   Link encap:Ethernet HWaddr 22:04:45:E2:85:21           BROADCAST  MTU:1500 Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b) Now we can add more ports to the OVS bridge and connect it to other namespaces or other device like physical interfaces. Neutron is using network namespaces to implement network services such as DCHP, routing, gateway, firewall, load balance and more. In the next post we will go into this in further details. Linux Bridge and veth pairs Linux bridge is used to connect the port from OVS to the VM. Every port goes from the OVS bridge to a Linux bridge and from there to the VM. The reason for using regular Linux bridges is for security groups’ enforcement. Security groups are implemented using iptables and iptables can only be applied to Linux bridges and not to OVS bridges. Veth pairs are used extensively throughout the network setup in OpenStack and are also a good tool to debug a network problem. Veth pairs are simply a virtual wire and so veths always come in pairs. Typically one side of the veth pair will connect to a bridge and the other side to another bridge or simply left as a usable interface. In this example we will create some veth pairs, connect them to bridges and test connectivity. This example is using regular Linux server and not an OpenStack node: Creating a veth pair, note that we define names for both ends: # ip link add veth0 type veth peer name veth1 # ifconfig -a . . veth0     Link encap:Ethernet HWaddr 5E:2C:E6:03:D0:17           BROADCAST MULTICAST  MTU:1500 Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b) veth1     Link encap:Ethernet HWaddr E6:B6:E2:6D:42:B8           BROADCAST MULTICAST  MTU:1500 Metric:1           RX packets:0 errors:0 dropped:0 overruns:0 frame:0           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b) . . To make the example more meaningful this we will create the following setup: veth0 => veth1 => br-eth3 => eth3 ======> eth2 on another Linux server br-eth3 – a regular Linux bridge which will be connected to veth1 and eth3 eth3 – a physical interface with no IP on it, connected to a private network eth2 – a physical interface on the remote Linux box connected to the private network and configured with the IP of 50.50.50.1 Once we create the setup we will ping 50.50.50.1 (the remote IP) through veth0 to test that the connection is up: # brctl addbr br-eth3 # brctl addif br-eth3 eth3 # brctl addif br-eth3 veth1 # brctl show bridge name     bridge id               STP enabled     interfaces br-eth3         8000.00505682e7f6       no              eth3                                                         veth1 # ifconfig veth0 50.50.50.50 # ping -I veth0 50.50.50.51 PING 50.50.50.51 (50.50.50.51) from 50.50.50.50 veth0: 56(84) bytes of data. 64 bytes from 50.50.50.51: icmp_seq=1 ttl=64 time=0.454 ms 64 bytes from 50.50.50.51: icmp_seq=2 ttl=64 time=0.298 ms When the naming is not as obvious as the previous example and we don't know who are the paired veth interfaces we can use the ethtool command to figure this out. The ethtool command returns an index we can look up using ip link command, for example: # ethtool -S veth1 NIC statistics: peer_ifindex: 12 # ip link . . 12: veth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 Summary That’s all for now, we quickly reviewed OVS, network namespaces, Linux bridges and veth pairs. These components are heavily used in the OpenStack network architecture we are exploring and understanding them well will be very useful when reviewing the different use cases. In the next post we will look at how the OpenStack network is laid out connecting the virtual machines to each other and to the external world. @RonenKofman

  Read the article

• Extract InstallSHIELD's CAB files when there is no HDR files?

  - by user433531

  layout.bin setup.lid _sys1.cab _user1.cab DATA.TAG data1.cab SETUP.INI setup.ins _INST32I.EX_ SETUP.EXE _ISDEL.EXE _SETUP.DLL lang.dat os.dat I want to extract an InstallSHIELD's 5 install package and above is the list of files in "data1" folder. However there is no *.hdr files so I can't extact the CAB files using tools on Internet, even though the package is still able to be installed without any error. Can anybody give me a suggestion for this please?

  Read the article

• Multi-monitor Usage

  - by logan2

  How many different applications do you use with a 2, 3, 4, 5 or more monitor setup? What's the most sophisticated multi-monitor setup you've seen? To be more specific, I would like to know exactly how you use your multi-monitor setup and how can I make better use of my own. How does someone take full advantage of a multi-monitor setup? And does having more monitors help your productivity?

  Read the article

• Dell "Remote Access Configuration Utility" keeps prompting

  - by Dan

  One of our servers can never reboot without pausing at the BIOS prompt asking to "F1 to continue, F2 to enter setup utility". I have gone into Setup and there is nothing there to stop it prompting for this; I have gone into the Remote Access Configuration Utility (CTRL+E) and have setup some values hoping that because it was setup it would not keep asking, but nope, nothing obvious like "Disable Remote Access Configuration". This is the screen we see: Does anyone know what we can do to let our machine boot cleanly??

  Read the article

• I have problem installing the sql server 2008 r2 on windows server 2008 r2. It gives me the following error.

  - by user411072

  TITLE: Microsoft SQL Server 2008 R2 Setup The following error has occurred: Error reading from file: C:\en_sql_server_2008_r2_standard_x86_x64_ia64_dvd_521546\1033_ENU_LP\x64\setup\sqlsupport_msi\PFiles\SqlServr\100\Setup\fe72iemr\e4grzzmx\x64\1033\ynzwp_7q.rtf. Verify that the file exists and that you can access it. For help, click: http://go.microsoft.com/fwlink?LinkID=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.50.1600.1&EvtType=0xDF039760%25401201%25401 BUTTONS: OK

  Read the article

• Visual Studio 2010 RC with .net 4 beta 2

  - by aip.cd.aish

  Does anyone know if it is possible to use Visual Studio 2010 RC with the beta 2 version of the .NET 4 framework? The reason I need to use the beta 2 version and not the RC is that there isn't an Expression Blend that can support the .NET 4 RC. I uninstalled the .NET 4 framework that installed with Visual Studio 2010, then I reinstalled the .NET 4 version Beta 2. But now when I launch Visual Studio, I get an error message saying "The operation could not be completed" and it shuts down. How can I make this work? Thanks!

  Read the article

• Java web start - Unable to load resource

  - by CD

  Hi all, I've got a jar that loads great with java web starter when I browse through the IP address of the server. Once I try the server name instead I get the following exception: com.sun.deploy.net.FailedDownloadException: Unable to load resource: at com.sun.deploy.net.DownloadEngine.actionDownload(Unknown Source) at com.sun.deploy.net.DownloadEngine.getCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getResourceCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getResourceCacheEntry(Unknown Source) at com.sun.deploy.net.DownloadEngine.getResource(Unknown Source) at com.sun.javaws.LaunchDownload$DownloadTask.call(Unknown Source) at java.util.concurrent.FutureTask$Sync.innerRun(Unknown Source) at java.util.concurrent.FutureTask.run(Unknown Source) at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(Unknown Source) at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source) at java.lang.Thread.run(Unknown Source) Any idea what should I look for?

  Read the article

• C# Confusing Results from Performance Test

  - by aip.cd.aish

  I am currently working on an image processing application. The application captures images from a webcam and then does some processing on it. The app needs to be real time responsive (ideally < 50ms to process each request). I have been doing some timing tests on the code I have and I found something very interesting (see below). clearLog(); log("Log cleared"); camera.QueryFrame(); camera.QueryFrame(); log("Camera buffer cleared"); Sensor s = t.val; log("Sx: " + S.X + " Sy: " + S.Y); Image<Bgr, Byte> cameraImage = camera.QueryFrame(); log("Camera output acuired for processing"); Each time the log is called the time since the beginning of the processing is displayed. Here is my log output: [3 ms]Log cleared [41 ms]Camera buffer cleared [41 ms]Sx: 589 Sy: 414 [112 ms]Camera output acuired for processing The timings are computed using a StopWatch from System.Diagonostics. QUESTION 1 I find this slightly interesting, since when the same method is called twice it executes in ~40ms and when it is called once the next time it took longer (~70ms). Assigning the value can't really be taking that long right? QUESTION 2 Also the timing for each step recorded above varies from time to time. The values for some steps are sometimes as low as 0ms and sometimes as high as 100ms. Though most of the numbers seem to be relatively consistent. I guess this may be because the CPU was used by some other process in the mean time? (If this is for some other reason, please let me know) Is there some way to ensure that when this function runs, it gets the highest priority? So that the speed test results will be consistently low (in terms of time). EDIT I change the code to remove the two blank query frames from above, so the code is now: clearLog(); log("Log cleared"); Sensor s = t.val; log("Sx: " + S.X + " Sy: " + S.Y); Image<Bgr, Byte> cameraImage = camera.QueryFrame(); log("Camera output acuired for processing"); The timing results are now: [2 ms]Log cleared [3 ms]Sx: 589 Sy: 414 [5 ms]Camera output acuired for processing The next steps now take longer (sometimes, the next step jumps to after 20-30ms, while the next step was previously almost instantaneous). I am guessing this is due to the CPU scheduling. Is there someway I can ensure the CPU does not get scheduled to do something else while it is running through this code?

  Read the article

• Control flex application from embedded Flash control

  - by aip.cd.aish

  I have a flex application and have embedded a flash (SWF) file into it using <mx:SWFLoader>. There is an "Exit" button on the Flash file. I want to be able to handle the button click event on the flex application. So when that button in the flash file is clicked, I want to perform an action in the parent flex application. How can I do this? Thanks!

  Read the article

• Implementing EAV pattern with Hibernate for User -> Settings relationship

  - by Trevor

  I'm trying to setup a simple EAV pattern in my web app using Java/Spring MVC and Hibernate. I can't seem to figure out the magic behind the hibernate XML setup for this scenario. My database table "SETUP" has three columns: user_id (FK) setup_item setup_value The database composite key is made up of user_id | setup_item Here's the Setup.java class: public class Setup implements CommonFormElements, Serializable { private Map data = new HashMap(); private String saveAction; private Integer speciesNamingList; private User user; Logger log = LoggerFactory.getLogger(Setup.class); public String getSaveAction() { return saveAction; } public void setSaveAction(String action) { this.saveAction = action; } public User getUser() { return user; } public void setUser(User user) { this.user = user; } public Integer getSpeciesNamingList() { return speciesNamingList; } public void setSpeciesNamingList(Integer speciesNamingList) { this.speciesNamingList = speciesNamingList; } public Map getData() { return data; } public void setData(Map data) { this.data = data; } } My problem with the Hibernate setup, is that I can't seem to figure out how to map out the fact that a foreign key and the key of a map will construct the composite key of the table... this is due to a lack of experience using Hibernate. Here's my initial attempt at getting this to work: <composite-id> <key-many-to-one foreign-key="id" name="user" column="user_id" class="Business.User"> <meta attribute="use-in-equals">true</meta> </key-many-to-one> </composite-id> <map lazy="false" name="data" table="setup"> <key column="user_id" property-ref="user"/> <composite-map-key class="Command.Setup"> <key-property name="data" column="setup_item" type="string"/> </composite-map-key> <element column="setup_value" not-null="true" type="string"/> </map> Any insight into how to properly map this common scenario would be most appreciated!

  Read the article

• C# Putting the required DLLs somewhere other than the root of the output

  - by aip.cd.aish

  I am using EmguCV for a project and when our program runs it needs some dlls like "cxcore.dll" etc. (or it throws runtime exceptions). At the moment, I put the files in the root of the output folder (selected "Copy Always" in the file's properties in Visual Studio). However it looks a bit messy, to have about 10 different dlls just there. Is there someway where I can move it to a subfolder in the output folder and it'll still find it.

  Read the article

• HPCM 11.1.2.2.x - How to find data in an HPCM Standard Costing database

  - by Jane Story

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Calibri","sans-serif"; mso-bidi-font-family:"Times New Roman";} When working with a Hyperion Profitability and Cost Management (HPCM) Standard Costing application, there can often be a requirement to check data or allocated results using reporting tools e.g Smartview. To do this, you are retrieving data directly from the Essbase databases related to your HPCM model. For information, running reports is covered in Chapter 9 of the HPCM User documentation. The aim of this blog is to provide a quick guide to finding this data for reporting in the HPCM generated Essbase database in v11.1.2.2.x of HPCM. In order to retrieve data from an HPCM generated Essbase database, it is important to understand each of the following dimensions in the Essbase database and where data is located within them: Measures dimension – identifies Measures AllocationType dimension – identifies Direct Allocation Data or Genealogy Allocation data Point Of View (POV) dimensions – there must be at least one, maximum of four. Business dimensions: Stage Business dimensions – these will be identified by the Stage prefix. Intra-Stage dimension – these will be identified by the _Intra suffix. Essbase outlines and reporting is explained in the documentation here:http://docs.oracle.com/cd/E17236_01/epm.1112/hpm_user/ch09s02.html For additional details on reporting measures, please review this section of the documentation:http://docs.oracle.com/cd/E17236_01/epm.1112/hpm_user/apas03.html Reporting requirements in HPCM quite often start with identifying non balanced items in the Stage Balancing report. The following documentation link provides help with identifying some of the items within the Stage Balancing report:http://docs.oracle.com/cd/E17236_01/epm.1112/hpm_user/generatestagebalancing.html The following are some types of data upon which you may want to report: Stage Data: Direct Input Assigned Input Data Assigned Output Data Idle Cost/Revenue Unassigned Cost/Revenue Over Driven Cost/Revenue Direct Allocation Data Genealogy Allocation Data Stage Data Stage Data consists of: Direct Input i.e. input data, the starting point of your allocation e.g. in Stage 1 Assigned Input Data i.e. the cost/revenue received from a prior stage (i.e. stage 2 and higher). Assigned Output Data i.e. for each stage, the data that will be assigned forward is assigned post stage data. Reporting on this data is explained in the documentation here:http://docs.oracle.com/cd/E17236_01/epm.1112/hpm_user/ch09s03.html Dimension Selection Measures Direct Input: CostInput RevenueInput Assigned Input (from previous stages): CostReceivedPriorStage RevenueReceivedPriorStage Assigned Output (to subsequent stages): CostAssignedPostStage RevenueAssignedPostStage AllocationType DirectAllocation POV One member from each POV dimension Stage Business Dimensions Any members for the stage business dimensions for the stage you wish to see the Stage data for. All other Dimensions NoMember Idle/Unassigned/OverDriven To view Idle, Unassigned or Overdriven Costs/Revenue, first select which stage for which you want to view this data. If multiple Stages have unassigned/idle, resolve the earliest first and re-run the calculation as differences in early stages will create unassigned/idle in later stages. Dimension Selection Measures Idle: IdleCost IdleRevenue Unassigned: UnAssignedCost UnAssignedRevenue Overdriven: OverDrivenCost OverDrivenRevenue AllocationType DirectAllocation POV One member from each POV dimension Dimensions in the Stage with Unassigned/ Idle/OverDriven Cost All the Stage Business dimensions in the Stage with Unassigned/Idle/Overdriven. Zoom in on each dimension to find the individual members to find which members have Unassigned/Idle/OverDriven data. All other Dimensions NoMember Direct Allocation Data Direct allocation data shows the data received by a destination intersection from a source intersection where a direct assignment(s) exists. Reporting on direct allocation data is explained in the documentation here:http://docs.oracle.com/cd/E17236_01/epm.1112/hpm_user/ch09s04.html You would select the following to report direct allocation data Dimension Selection Measures CostReceivedPriorStage AllocationType DirectAllocation POV One member from each POV dimension Stage Business Dimensions Any members for the SOURCE stage business dimensions and the DESTINATION stage business dimensions for the direct allocations for the stage you wish to report on. All other Dimensions NoMember Genealogy Allocation Data Genealogy allocation data shows the indirect data relationships between stages. Genealogy calculations run in the HPCM Reporting database only. Reporting on genealogy data is explained in the documentation here:http://docs.oracle.com/cd/E17236_01/epm.1112/hpm_user/ch09s05.html Dimension Selection Measures CostReceivedPriorStage AllocationType GenealogyAllocation (IndirectAllocation in 11.1.2.1 and prior versions) POV One member from each POV dimension Stage Business Dimensions Any stage business dimension members from the STARTING stage in Genealogy Any stage business dimension members from the INTERMEDIATE stage(s) in Genealogy Any stage business dimension members from the ENDING stage in Genealogy All other Dimensions NoMember Notes If you still don’t see data after checking the above, please check the following Check the calculation has been run. Here are couple of indicators that might help them with that. Note the size of essbase cube before and after calculations ensure that a calculation was run against the database you are examing. Export the essbase data to a text file to confirm that some data exists. Examine the date and time on task area to see when, if any, calculations were run and what choices were used (e.g. Genealogy choices) If data does not exist in places where they are expecting, it could be that No calculations/genealogy were run No calculations were successfully run The model/data at feeder location were either absent or incompatible, resulting in no allocation e.g no driver data. Smartview Invocation from HPCM From version 11.1.2.2.350 of HPCM (this version will be GA shortly), it is possible to directly invoke Smartview from HPCM. There is guided navigation before the Smartview invocation and it is then possible to see the selected value(s) in SmartView. Click to Download HPCM 11.1.2.2.x - How to find data in an HPCM Standard Costing database (Right click or option-click the link and choose "Save As..." to download this pdf file)

  Read the article

• Rhythmbox goes crazy if I change keyboard layout

  - by krokoziabla

  Not so trivial to explain but I'll try. Launch Rhythmbox Insert a CD in the CD-ROM The CD is not automatically identified (it's of a not very famous Russian band) I'm manually setting track names and... Magic, black magic! If I change the keyboard layout (RU <- EN) during editing then Rhythmbox kicks me out of the editing. So if a track name contains both Russian and English words I'm compelled to write one part, press Enter (so that the changes are not lost), change layout, click on the track name, write another part in the opposite layout. In some tricky names I have to do this several times. By the way, I use Alt+Shift to change layout. Any ideas?

  Read the article

• Android:Where is exactly Android 1.6 SDK download?

  - by user187532

  Hello friends, I want install Android version 1.6 SDK. I already have Android development setup with Eclipse and Android 1.5 SDK. Wherever i search in Google to download Android 1.6 SDK, it finally goes to link: http://developer.android.com/intl/zh-CN/sdk/index.html This link has three setup SDK zip files, but no where mentioned what version of SDK setup are those? Why such confusions in this Android website for showing just version of SDK setup files? Where i can get exactly Android 1.6 SDK setup download? Could someone point out me clearly? Is there any special steps that i need to follow to overwrite 1.6 SDK with my existing setup environment? Thank you.

  Read the article

• Install Ubuntu and erase Windows Vista

  - by miguel

  I have an older laptop with a ADA hard disk I can't really buy a new one so I want to erase Windows Vista on my computer and only have Ubuntu so that I can have more space. How do I make it go directly to my blank CD? My Windows Vista is messed up and I can't even get into it. I want to download the new version of Ubuntu while in Ubuntu. I downloaded it but it didn't go directly to the blank CD. I tried to copy all of Ubuntu onto the CD once it was downloaded but it says there was an error while copying. What should I do?

  Read the article

• Running Visual Studio 2008 and 2010 at the same time

  - by aip.cd.aish

  A group of us are working on a project which we built with .NET 3.5 in Visual Studio 2008. I want to test out Visual Studio 2010 and .NET 4 (well, mainly for WPF 4). I am just wondering if I install VS 2010, will I still be able to use VS 2008 to open the first project. I know when I open older projects made in VS 2003/2005, I get an upgrade wizard. I do not want to upgrade the first project to 2010, since that would probably mean every one else has to use it too. I have not done this before, is it possible to run both versions of Visual Studio, where each version opens its own projects (this may not even be an issue, but I just wanted someone to confirm this, so that I don't spend a lot of time trying to undo changes)?

  Read the article

• Installation of 11.10 on new drive (no OS)

  - by Jeffrey Vincent

  I have a Dell Dimension 600 XPS Phoenix BIOS version A03, the original HD crashed and burned. Dell didn't send OS disks (was on the original drive and no back up disks), so I am trying to install Ubuntu 11.10 on the new drive. The new drive is a Western Digital 1TB. I formatted the new drive by putting it in an enclosure and formatting it with Windows 7 on my HP system. When I put the cd in the cdrom it boots to the cd with the Advanced user screen (won't boot into the usually Windows GUI). When I try to install (or run from live Cd) I get the same error message. Same with trying the various boot options. The message is: VFS: cannot open root device "(NULL)" or unknown-block(8,1) Please append a correct "root=" boot option: Here are the available partitions: Kernal Panic- not syncing: VFS: Unable to mount rootfs on unknown-block(8,1) and then it lists Trace messages then freezing. Any help or suggestions are appreciated in advance.

  Read the article

• Sarg Daily Report not generated

  - by Suleman

  Ubuntu 12.04 LTS Squid 3 Sarg 2.3.2 following is my crontab configuration # SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin m h dom mon dow user command 25 6 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly ) # this does not generate daily html report.

  Read the article

• $RECYCLE.BIN.trashinfo: Input/output error

  - by Parto

  I cannot delete .Trash-503 folder via GUI or terminal, it returns a $RECYCLE.BIN.trashinfo: Input/output error Even sudo rm -r or even an ls works in that directory. Check terminal output below: subroot@subroot:~$ cd /media/xxxxx/ subroot@subroot:/media/xxxxx$ rm .Trash-503/ rm: cannot remove `.Trash-503/': Is a directory subroot@subroot:/media/xxxxx$ rm -r .Trash-503/ rm: cannot remove `.Trash-503/info/$RECYCLE.BIN.trashinfo': Input/output error rm: cannot remove `.Trash-503/info/found.000.trashinfo': Input/output error rm: cannot remove `.Trash-503/info': Directory not empty subroot@subroot:/media/BONJOUR$ sudo rm -r .Trash-503/ [sudo] password for subroot: rm: cannot remove `.Trash-503/info/$RECYCLE.BIN.trashinfo': Input/output error rm: cannot remove `.Trash-503/info/found.000.trashinfo': Input/output error subroot@subroot:/media/xxxxx$ cd .Trash-503/ subroot@subroot:/media/xxxxx/.Trash-503$ ls info subroot@subroot:/media/xxxxx/.Trash-503$ cd info/ subroot@subroot:/media/xxxxx/.Trash-503/info$ ls ls: cannot access $RECYCLE.BIN.trashinfo: Input/output error ls: cannot access found.000.trashinfo: Input/output error found.000.trashinfo $RECYCLE.BIN.trashinfo subroot@subroot:/media/xxxxx/.Trash-503/info$ What's going on here and how can I delete this folder?

  Read the article

• Error installing Windows7 64 bits on VirtualBox

  - by MetaDark

  I am trying to set up Windows in Virtual Box, so I don't need to reboot in the rare occasion that I actually need it. The problem is, Virtual Box doesn't preform any errors when I insert the 32bit installation CD but when I try to use the 64bit installation; What!? I am already using the installation disc! I've checked my BIOS to see if I have SVM (AMD's version of VT) disabled and all I see is "Enabled" I have a K9N6PGM2-V2 motherboard A Triple Core AMD Athlon II A Nvdia NForce 430 integrated graphics card 4GB of RAM An 80GB IDE And a 1TB SATA I don't think the last three specifications matter but just in case XP I am pretty sure the CD isn't broken ( I am going to make sure in just a moment ), what could be the cause to this problem? Edit: The 64bit installation CD is not broken, but I found out when trying to install from the 32bit version that it's trying to upgrade, not preform a fresh install - Odd.

  Read the article

• FFMPEG compilation errors

  - by Nitin Sagar

  First of all i am a newbie to Ubuntu Linux and have been trying to install and compile FFMPEG on an Ubuntu machine... I am trying to compile FFMPEG on an Ubuntu machine, using the following link reference: https://ffmpeg.org/trac/ffmpeg/wiki/UbuntuCompilationGuide I have already install git packages from resource centre whatever it results in search... Whatever i am trying to clone to is showing the below error... and please note that the network is wireless and connected with full bandwidth and i am able to browse through website and not sure why its showing an error as unable to connect and connection timed out.... root@ubuntu:~# cd root@ubuntu:~# git clone --depth 1 git://github.com/mstorsjo/fdk-aac.git Cloning into 'fdk-aac'... fatal: unable to connect to github.com: github.com[0: 207.97.227.239]: errno=Connection timed out Tried these commands as well to install x264 lib: cd git clone --depth 1 git://git.videolan.org/x264 cd x264 I am doing all this as a root user. Any help and comments would be appreciated. Thanks Nitin

  Read the article

• Help me make a cronjob/screen command please?

  - by Josip Gòdly Zirdum

  Hi guys I want to set up a cronjob on reboot to do this cd /home/admin/vivalaminecraft.com && screen -d -m -S mcscreen && mono McMyAdmin.exe The issue is when I execute this it seems to create the screen but doesn't do the mono McMyAdmin.exe in the screen... Is there like a then command ? so it does 1. then 2. then 3. ? Could someone please help out :) So I tried this: so I did this: @reboot screen -dmS minecraft @reboot cd /home/admin/vivalaminecraft.com @reboot mono McMyAdmin.exe It still doesn't work. The screen is created but it doesn't have the mono execution in it I put this in it #!/bin/bash screen -dmS minecraft; cd /home/admin/vivalaminecraft.com; mono McMyAdmin.exe; is this correct?

  Read the article

• How do I install Ubuntu on an iMac 27"?

  - by jml

  I have a beautiful 27" iMac. I would like to run Ubuntu on it natively, dual-booting with OS X. I have rEFIt installed, and I can boot into the Ubuntu 10.10 CD, kind of. Here's what happens: I select the CD from the rEFIt menu It loads for a while, then flashes up an aubergine screen with a very low-res picture of a human, an arrow and a keyboard It sits there for a while It changes to 80x25 console mode The screen then goes black, as if nothing is displaying to it All the while, the CD is churning away as if something is reading from it. What do I do?

  Read the article

• Weird cabal error: "inappropriate type"

  - by Bill

  ~ % cabal install --reinstall time Resolving dependencies... [1 of 1] Compiling Main ( /var/folders/0D/0D3du+YyGzuRETgUJZ5m8U+++TI/-Tmp-/time-1.2.0.251774/time-1.2.0.2/Setup.hs, /var/folders/0D/0D3du+YyGzuRETgUJZ5m8U+++TI/-Tmp-/time-1.2.0.251774/time-1.2.0.2/dist/setup/Main.o ) Linking /var/folders/0D/0D3du+YyGzuRETgUJZ5m8U+++TI/-Tmp-/time-1.2.0.251774/time-1.2.0.2/dist/setup/setup ... Configuring time-1.2.0.2... setup: dist/setup-config51799.tmp: inappropriate type cabal: Error: some packages failed to install: time-1.2.0.2 failed during the configure step. The exception was: ExitFailure 1 ~ % Has anyone seen this before?

  Read the article

< Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >