Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 108/287 | < Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >

  • Cannot find the "Create Network" menuitem in the WiFi icon menu in Mountain Lion

    - by Chuancong
    I am using Mountain Lion Developer Preview 2. I cannot find the "Create Network" menuitem in the WiFi icon menu in the menubar. It was there before when I was using Lion. It started missing since I upgraded to Mountain Lion Developer Preview 1. By the way, is there any other method to create an ad-hoc WiFi network on OS X? I tried to use Internet Sharing via WiFi, but other devices using the shared connection could not find the Mac in their local networks. I am using an early 2011 MacBook Pro 15'. Thanks.

    Read the article

  • SOHO NETGEAR wireless router disconnects when downloading torrents

    - by Lirik
    I have a NETGEAR WGT624 wireless router at home which dies when there is a heavy torrent load. I open up my torrent client and it downloads for about 5 to 10 minutes and it continues to increase the number of seeds (goes up to 70-80 seeds), but after that the router simply fails and I have to restart it in order to get an internet connection again. When I connect directly via an ethernet cable the router and open up the torrent client, then it seems to be doing fine, but when I go wireless then the router stops working properly (although all the lights are still blinking as normal). Is there any way that I can fix this? New router firmware? Change some router options? Feed it a cookie? Anything?

    Read the article

  • Connecting a Mac to the office network

    - by user36501
    Hi All, I am busy preparing to start working with a Mac at work - in addition to my old PC. Just wondered, is it difficult to setup the Mac to run on the office network - i.e. does it need any special settings or servers or anything like that? and also printers...can I use the network printer as normal. I am just pottrying to think ahead of any ential issues. Also share drives...will I be able to access share drives and my backups to these shares drives - all a bit daunting! Btw in case you didn't notice I am a Mac Nube lol

    Read the article

  • how does ospf control flooding?

    - by iamrohitbanga
    what method is used by ospf protocol to prevent looping of flooded packets for link state advertisements? The packet header does not contain any timestamp. How do the routers recognize that it is the same advertisement that they sent before?

    Read the article

  • Windows XP unknown location popup annoyance

    - by mcgyver5
    I'm plagued by a popup from Windows XP when I use wireless. It says, "You are in an Unknown Location..." It always pops above whatever window I'm using, but does not take focus, so while it does not interrupt my typing, it gets in the way and I can't dismiss it with a keystroke. I'd like to find a way to disable this popup. I've searched in control panel -- Network Connections. I'm not referring to "balloon tips" that appear related to the wireless connection in a new location.

    Read the article

  • Free IP address management software

    - by TiFFolk
    We are choosing a system for managing our IP address space. So we are looking for a special free software like IPPlan. So what we have nowadays: Ipplan (Beta IPv6 support) SolarWinds IP address tracker (IPv6 support unknown ) IP module of The NOC Project (BTW, take a look of it, seems to be very promising project) (IPv6 support unknown ) phpIP (Does not support IPv6) IP management from RackTables (Does not support IPv6) Do you know about any other special software, like written above? But: No Wiki No DNS No DHCP No spreadsheet Software should provide: Clear view of available addresses Detail listing of all addresses by subnets/search pattern/owners/additional info It must support adding additional info like owner of IP, domain-name, contacts, etc Multi user support Easy interface Software has to be specially written for address management. Scalability Any OS: win, lin, sol, web

    Read the article

  • Public static ip for vagrant box

    - by Numbata
    I have server (Debian Squeeze) with 1 ethernet card and 2 public static IPs (188.120.245.4 and 188.120.244.5). What I want: Setup virtual box (Ubuntu) with access via static IP (188.120.244.5). What I was trying: config.vm.forward_port - good idea: setup interface "eth1:1" with 188.120.244.5 on host-machine, and add to Vagrant file "config.vm.forward_port = hmm..?" config.vm.network :hostonly, "188.120.244.5" - not working. Was created new interface on host-machine with ip "188.120.244.1". Of course 188.120.244.1 IP isn't mine and I can't access my server via this IP. config.vm.network :bridged - I'm confused how this works :) What I have now: Not working configuration. Debian-host-machine# cat Vagrantfile Vagrant::Config.run do |config| config.vm.define :gitlab do |box_config| box_config.vm.box = "ubuntu" box_config.vm.host_name = "ubuntu" box_config.vm.network :bridged box_config.vm.network :hostonly, "188.120.244.5", :auto_config => false end end Debian-host-machine# ifconfig eth1 Link encap:Ethernet HWaddr 00:15:17:69:71:bb inet addr:188.120.245.4 Bcast:188.120.247.255 Mask:255.255.248.0 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:188.120.244.1 Bcast:188.120.246.255 Mask:255.255.255.0 Ubuntu-virtual-machine# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:ee:8d:0c inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 eth1 Link encap:Ethernet HWaddr 08:00:27:45:71:87 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 How I can access virtual box via public static IP from network? I'm using Oracle VM VirtualBox Manager 4.1.18 and Vagrant version 1.0.3. Thanks in advance for your feedback.

    Read the article

  • How to setup Mac server to use two gateways

    - by Brady
    I recently asked this question: How to set Mac server to use different Gateway for internet bound traffic The answer given works but has presented me with another issue that I didnt make clear in that question. Here is my network layout as it stands: At the moment outside staff members use some services on the existing internet 1 link. Those services are hosted by the Mac server. If I change the gateway of the Mac server to the second modem those outside staff lose visabilty on those services. Now I dont know how to go about solving this issue. I want the second link to be used when the Mac server goes to rsync data offsite but everything else use link one. How do I do this? Thanks Scott EDIT: This has been resolved by setting the default gateway on the Mac server to 192.168.1.254 Thus leaving everything on the network as it was before. but to get the Mac server to use the other link for rsync I've added a route to the Mac server to route traffic to the rsync server through the second gateway. sudo route add -net {server IP's}/{Netmask} 192.168.1.1 I've awarded the answer to gravyface for pointing me to a post on how to make this route persistant in Mac

    Read the article

  • One network, two macbooks, one is fast and the other is slow

    - by Brendan
    I really need help for my friend. I know next to nothing about computers. My roommate and I both have macbook pros from the same year running OS X, are both connecting wirelessly to the same xfinity wifi, and while mine runs perfectly fine, my roommate complains that his works very slowly and times out every few seconds. I can't seem to figure out why this is. He is trying to get me to switch internet providers because he is convinced that it is their problem, but this cannot possibly be the issue since it works great on mine. He has an xbox hooked up to the wifi that he says also works poorly. I really can't see switching providers given that I am experiencing absolutely zero problems. How can I help my friend?

    Read the article

  • Verify server performance

    - by George Kesler
    I'm looking for a quick and SIMPLE way to verify that new servers are performing as expected. The most important metric is disk performance, second is network performance. I’m trying to prevent problems caused by misconfiguration of RAID arrays, NIC teaming etc. The solution should work with both physical and virtual servers. I don’t need sophisticated analysis with different workloads, just one set of benchmarks which I would run against a reference server and later compare to new ones. One problem is that most benchmarks are not giving accurate results when running on a VM.

    Read the article

  • Map FTP folder to folder on different FTP server

    - by jolt
    In my team we work a lot with FTP. We upload and download files from several different servers daily. Currently every member of the team manages access credentials to each FTP server locally on their own machine. I am looking for a way to set up a central FTP server that we can connect to, and from there, navigate to folders that each represent one of the other FTP servers that we connect to daily. Something like this: In-house central FTP server: |- FolderA --> server A root folder |- FolderB --> server B root folder |- FolderC --> server C root folder A setup like this, would mean that we can manage access credentials on the central FTP server, and team members would only need to have the access credentials to the central FTP server, and from there they could navigate to the other servers through these "virtual" folders. We could potentially develop our own custom FTP server that just forward requests to the remote FTP servers, but i feel like something like this (or something similar) would already have been done. So I'm looking for pointers that could help us find software for Windows that could help us to simplify our current setup. Thank you! Similar (unanswered) question here: FTP management server

    Read the article

  • How to send a popup message to unknow computer connected to my WLAN?

    - by Leandro
    Is there any way to send a popup message from a Linux systen to a "random" laptop/tablet/mobile linked to my Wireless network ? For example, if I let my WLAN open and I see a not recognized computer connected to it, is there anyway to send to that device a message ? On the other hand, if I am connected to someone else open network and they may or may not be aware that their network is open, can I send them a message warning that I am accessing their network? Probably for a completely "random" device the answer should be no. But if we restrict to laptops with Win7 or Linux SO is there any service running by default on such systems that allows one to send such popup messages ? PS: I have no practical motivation for this question. This is only a curiosity.

    Read the article

  • How should I isolate computers with different roles on a network

    - by fishhead
    I work in an industrial plant and we have one network(physical wire) that us used for both office usage and for process systems. The office computers are only used for typical office needs but occasionally do connect to the process computers to obtain information from a sql server or for some other purpose. A new initiative is in the works and is rolling down hill from corporate and that is to standardize how the the computers are used at work and they would be severely locked down and only a standard set of applications will be allowed to execute. one of the requirements is to also have non office computers isolated from the company domain. our non-office computers are a mix of Man-Machine interfaces and sql-servers all running software that non standard. My question is, how can we divorce the control systems computers from the company domain but still have access to the servers from the company domain. thanks

    Read the article

  • How should I isolate computers with different roles on a network

    - by fishhead
    I work in an industrial plant and we have one network(physical wire) that us used for both office usage and for process systems. The office computers are only used for typical office needs but occasionally do connect to the process computers to obtain information from a sql server or for some other purpose. A new initiative is in the works and is rolling down hill from corporate and that is to standardize how the the computers are used at work and they would be severely locked down and only a standard set of applications will be allowed to execute. one of the requirements is to also have non office computers isolated from the company domain. our non-office computers are a mix of Man-Machine interfaces and sql-servers all running software that non standard. My question is, how can we divorce the control systems computers from the company domain but still have access to the servers from the company domain. thanks

    Read the article

  • Cisco Catalyst 4500 Policy Based Routing

    - by Logan
    In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

    Read the article

  • Force10 S60 remote management

    - by StaringSkyward
    We've got a Force10 S60 switch to replace an older Cisco. I can't find a way to give the switch itself an IP address on the local VLAN so I can ssh to it. The config guide talks about using either a management interface on a separate management network or dedicating e.g. a gigabit port as a management port with a dedicated IP address. Ideally I would like to do what we do currently with the Cisco switches, which is in effect give the entire switch an IP so it can be reached from any host on the same VLAN without having to use up a physical port on the switch or physically connect the management port to another device. Is this possible with the S60 and if so, how would you give it, say the address 10.0.1.1 in vlan 10 (10.0.1.1/24)? Thanks!!!

    Read the article

  • How can I view my IIS hosted sites on other machines on my network

    - by Truegilly
    Hello, at home i have a simple network setup conatining 2 machines and 1 belkin router. On one machine i have a site hosted with IIS7. Rather than the standard localhost/index.htm address i have added an entry in the HOSTS file pointing the local ip (127.0.0.1) to this domain - www.mysite.dev. i can access the site with www.mysite.dev with no problem. what i would like to do is be able to view this site from my other machine on the network. initially i assumed this could be done with a url like so MACHINE-NAME/www.mysite.dev, but the connection always times out. But I can ping MACHINE-NAME without problems. For testing purposes i have diabled the windows firewall on both machines but to no joy. Like a typical web developer, my techy/network skills are pretty poor. Can anyone see where im going wrong ?? thank you for your time Truegilly :)

    Read the article

  • I Made Wordpress Multisite. And Now Everything Doesn't Display Properly

    - by piratepartypumpkin
    I installed Ubuntu 10.4 then I installed Bitnami LAMP stack then I installed bitnami wordpress module then I tried to make the site into a multisite by following these instructions: http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite#How_to_add_several_WordPress_Multisite_blogs_with_different_domains.3f AND http://wiki.bitnami.org/Applications/BitNami_WordPress_Multisite I can elaborate if needed: I enabled multisite in my wp-config.php file. Then I created a network using the wordpress dashboard. I was given two blocks of text to copy and paste 1 block into my wp-config.php file and one into my .htaccess file. I did that and now I get this: When I go to my mywebsite.com I get this (this was there before I switched to multisite): If I go to mywebsite.com/wordpress I get this (this used to be a functioning wordpress theme): If I click on "My Blog" it redirects to 1mywebsite.com (where the "1" came from I have no idea) If I try to login by going to mywebsite.com/wordpress/wp-login I get this: and if I enter my user and password it redirects me to mywebsite.com/wp-login.php and gives me "Not Found" The requested URL /wp-login.php was not found on this server. NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /opt/lampstack-5.3.16-0/apps/wordpress ServerName mywebsite.com ServerAlias www.mywebsite.com </VirtualHost>

    Read the article

  • How to share internet connection on Mac os x to Virtualbox vm's using Host-only

    - by redben
    In one line : is the following possible : Airport <- osx bridge - vbox-Host-only - vm's On a mac os x, i have virtual box with a virtual machine. For now i have configured 2 interfaces for my virtual machine eth0 is normal bridge for my vm to acces the internet (when airport is connected) eth1 is set to host-only so i can access my vm from the host when there is no wifi/aiport is down. So basically it's like Adapter 1 when there is Wifi, Adapter 2 when there is not. I'd like to have only one configuration to make it simpler. I thought i could just keep the Host only configuration, and on the host (os x) go to internet sharing and select "share from airport" to vboxnet0 (the vb virtual interface). Only to find out that vboxnet0 dosn't show up in the interfaces list on os x preferences. I know that on a linux host you could install something called bridge-utils and use that to bridge the two insterfaces. Is there any thing like that for Mac ?

    Read the article

  • One Mac computer with multiple network connections?

    - by Kyle Lowry
    I have a Mac (OS X 10.5) that I would like to connect to a dedicated/isolated Internet connection (one that is not connected to the LAN), and a LAN. The LAN is set up with its own, separate, Internet connection which is shared by several dozen computers (and is quite slow). I want to set it up so that the Mac uses its own dedicated Internet connection (on a different account with a different company) for its Internet access, but can still access the local area network as well. How can I configure the Mac & the network to allow this?

    Read the article

  • snmptt not translating traps, even with translate_log_trap_oid=1

    - by mbrownnyc
    I am having some trouble configuring snmptt to properly translate snmp traps. The following is a problem: /etc/snmp/snmptt.conf reflects: EVENT fgFmTrapIfChange .1.3.6.1.4.1.12356.101.6.0.1004 "Status Events" Critical FORMAT $* EXEC /usr/local/nagios/libexec/eventhandlers/submit_check_result $r "snmp_traps" 2 "$O: $+*" "$*" SDESC Trap is sent to the managing FortiManager if an interface IP is changed Variables: 1: fnSysSerial 2: ifName 3: fgManIfIp 4: fgManIfMask EDESC when a trap is received, /var/log/messages reflects: Sep 6 12:07:32 SNMPMANAGERHOST snmptrapd[15385]: 2012-09-06 12:07:32 <UNKNOWN> [UDP: [192.168.100.2]:162->[192.168.100.31]]: #012.1.3.6.1.2.1.1.3.0 = Timeticks: (707253943) 81 days, 20:35:39.43 #011.1.3.6.1.6.3.1.1.4.1.0 = OID: .1.3.6.1.4.1.12356.101.6.0.1004 #011.1.3.6.1.4.1.12356.100.1.1.1.0 = STRING: FGTNNNNNNNNN #011.1.3.6.1.2.1.31.1.1.1.1.10 = STRING: internal4 #011.1.3.6.1.4.1.12356.101.6.2.1.0 = IpAddress: 192.168.65.100 #011.1.3.6.1.4.1.12356.101.6.2.2.0 = IpAddress: 255.255.255.0 Sep 6 12:07:37 SNMPMANAGERHOST icinga: EXTERNAL COMMAND: PROCESS_SERVICE_CHECK_RESULT; 192.168.100.2; snmp_traps; 2; enterprises.12356.101.6.0.1004: enterprises.12356.100.1.1.1.0:FGTNNNNNNNNN ifName.10:internal4 enterprises.12356.101.6.2.1.0:192.168.65.100 enterprises.12356.101.6.2.2.0:255.255.255.0 Since the icinga entry reflects the EXEC, it's obvious there is no translations occurring by snmptt. I have verified that translate_log_trap_oid and net_snmp_perl_enable is enabled in snmptt.ini When using --debug=1 to start snmptt, I see the following in the --debugfile: ********** Net-SNMP version 5.05 Perl module enabled ********** The main NET-SNMP version is reported as NET-SNMP version: 5.5. What else can be done to verify that snmptt is configured properly to translate traps? I have run snmptt-net-snmp-test to verify whatever net-snmp-perl version I have installed properly supports translations. The output indicates it does. /root/snmptt_1.3/snmptt-net-snmp-test --best_guess=2 SNMPTT Net-SNMP Test v1.0 (c) 2003 Alex Burger http://snmptt.sourceforge.net MIBS:RFC1213-MIB best_guess: 2 Testing translateObj ******************** Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=disabled Test passed. Result: sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=disabled, include_module=enabled Test passed. Result: RFC1213-MIB::sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=disabled Test passed. Result: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: .1.3.6.1.2.1.1.1, long_names=enabled, include_module=enabled Test passed. Result: RFC1213-MIB::.iso.org.dod.internet.mgmt.mib-2.system.sysDescr Testing: sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: RFC1213-MIB::system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing: .iso.org.dod.internet.mgmt.mib-2.system.sysDescr, long_names=disabled, include_module=disabled Test passed. Result: .1.3.6.1.2.1.1.1 Testing getType *************** Testing: .1.3.6.1.2.1.4.1 Test passed. Result: INTEGER Testing: ipForwarding Test passed. Result: INTEGER Testing Description ******************* Test passed. Result: ------------------------------------------------- The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value. ------------------------------------------------- I have manually gone through the MIB with the definition that's not resolving, and verified that it is properly linking back to the proper resolved definition. It is: FORTINET-FORTIGATE-MIB.txt contains: fgFmTrapIfChange NOTIFICATION-TYPE OBJECTS { fnSysSerial, ifName, fgManIfIp, fgManIfMask } STATUS current DESCRIPTION "Trap is sent to the managing FortiManager if an interface IP is changed" ::= { fgFmTrapPrefix 1004 } fgFmTrapPrefix OBJECT IDENTIFIER ::= { fgMgmt 0 } fgMgmt OBJECT IDENTIFIER ::= { fnFortiGateMib 6 } fnFortiGateMib ::= { fortinet 101 } IMPORTS FnBoolState, FnIndex, fnAdminEntry, fnSysSerial, fortinet FROM FORTINET-CORE-MIB fortinet MODULE-IDENTITY ::= { enterprises 12356 } LOOKS GOOD!!!!! 1.3.6.1.4.1.12356.101.6.0.1004 I've exhausted all the documentation and even posted fruitlessly in the snmptt-users mailing list. I can not prove it is the MIB. Why would snmptt fail to translate traps? Thanks, Matt

    Read the article

< Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >