Search Results

Search found 22756 results on 911 pages for 'cisco vpn client'.

Page 109/911 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

• Spanning-Tree and redundant links

  - by Franko

  I have 2 switches which have redundancy between them, meaning fa0/1 on SW1 is connected to fa0/1 on SW2, and fa0/2 on SW1 is connected to fa0/2 on SW2. Both of the switches have the same BID, however the MAC address of SW1 is numerically lower, hence making it the root bridge. Now my question is, on SW2, what determines which of fa0/1 and fa0/2 becomes the RP (Root Port) and the other on blocking state?

  Read the article

• LOCAL and RADIUS authentication on ASA

  - by ghp

  Have configured local authentication which was working fine.And today I wanted to implement RADIUS too .. but after I have done, Im unable to login to my firewall user-identity default-domain LOCAL aaa authentication ssh console LOCAL and RADIUS aaa-server RADIUS protocol radius aaa-server RADIUS (inside) host xyzabc Key zzzzzz aaa authentication ssh console RADIUS aaa authentication enable console RADIUS aaa authentication http console RADIUS Can someone help me login to my firewall

  Read the article

• Assist me access my firewall using ASDM

  - by ghp

  Have configured my asa 5520 with all the interfaces inside -- 10.11.12.1 outside - 70.71.72.4 Have not connected the management interface ..left it as is. Im remotely accessing this firewall from a different location by SSH, but would like to use the asdm to access it remotely. I have configured the HTTP SERVER enable and assigned http 10.11.12.254 255.255.255.255 inside Please can someone let me know the config which can help me access this firewall using ASDM.

  Read the article

• Encryption over gigabit carrier ethernet

  - by Roy

  I would like to encrypt traffic between two data centres. Communication between the sites is provided as a standard provider bridge (s-vlan/802.1ad), so that our local vlan tags (c-vlan/802.1q) are preserved on the trunk. The communication traverse several layer 2 hops in the provider network. Border switches on both sides are Catalyst 3750-X with the MACSec service module, but I assume MACSec is out of the question, as I don't see any way to ensure L2 equality between the switches over a trunk, although it may be possible over a provider bridge. MPLS (using EoMPLS) would certainly allow this option, but is not available in this case. Either way, equipment can always be replaced to accommodate technology and topology choices. How do I go about finding viable technology options that can provide layer 2 point-to-point encryption over ethernet carrier networks?

  Read the article

• Planning office network [closed]

  - by gakhov

  I'm planning to setup my office network from scratch and want to ask professional opinions or tips. My office is connected to Internet with Cable connection (100Mb/s). The devices i would like to connect are VoIP Phone (RJ-11), TV (WiFi/LAN), 3 laptops (WiFi), a few smartphones (WiFi), iPad (WiFi), Kindle (WiFi) and, probably, MediaServer (WiFi/LAN). As you can see, the most load will be on WiFi connections (probably, even if TV supports WiFi it's better to connect it by LAN?). So, i need help to choose the best routers combination (or even one?) to support stable connections for all these devices and minimize the total number of routers/adapters. Any thoughts? Thank you!

  Read the article

• NAT : understanding about interconnection

  - by PITCHY

  English version below J'ai 2 routeurs A et B relié en série avec les ip respectives ( 10.0.0.1/30 10.0.0.2/30) sur le routeur A j'ai activé la fonction NAT avec un pool (200.0.0.1 - 200.0.0.15/28). Lorsque je sors je prends donc un ip du pool par exemple 200.0.0.10. Comment ça fonctionne sachant que ma nouvelle ip (200.0.0.10) ne se trouve pas sur le meme réseau que mon interface de destination (10.0.0.2)? English: I have 2 routers A and B, interconnected with a serial connection, with the ip's 10.0.0.1/30 for A and 10.0.0.2/30 for B. On router A NAT was activated with the pool 200.0.0.1 - 200.0.0.15/28. When connection to this router, I get an ip from the pool, for example 200.0.0.10. Knowing my new ip is 200.0.0.10, which is not on the same network as my destination interface (10.0.0.2), how can this work?

  Read the article

• Outbound Traffic Logging on ASA 5520 possible?

  - by j2k4j

  Taking a look at the ASDM (6.4) for my ASA 5520, I get a nice summary of the traffic status, with items like "interface traffic usage", and "connections per second". This works well, but only shows the data for the last 5-6 minutes or so. Recently, I've been asked whether it's possible to pull up this same type of traffic data for a particular time in the past. (Such as: Find the traffic usage for a 3 minute period from date xx:xx:xx @ time xx:xx:xx) I've noticed that my ASA 5520 is logging the warning, errors, etc that it is processing. But traffic data is not logged (yet) according to my search through the ASA. Is logging the traffic data amounts (as wondered above) actually a possibility? Is there any way to find out the past data for traffic and such values? Thanks!

  Read the article

• Can iranians do CCNA?

  - by Mark

  I know that Iranians can not do Sun's Java certification, how about CCNA? I've heard there is no examination centers in Iran, but can I do it outside Iran?

  Read the article

• Are neighbors formed in EIGRP and OSPF always directly connectly?

  - by xczzhh

  I always thought that neighbors formed in EIGRP were not necessarily directly connected because the only requirement for two routers to be neighbors is that they share the same Autonomous System and K-values, but it seems that I was wrong. I have looked up several books, they do not seem to give a clear answer. And I am even more confused with OSPF... Please, give me some light here. Thank you.

  Read the article

• Have NetFlow show true destinations...

  - by DeliriumTremens

  Currently NetFlow is showing destination (of inbound traffic) as our outside IP rather than inside IP. Also, for all outbound traffic, it is showing the source as our firewall rather than workstations. Any ideas about how to find the true source/destination for these?

  Read the article

• how to communicate in typical router switch router scenario?

  - by Kossel

  I'm learning routing using packet tracer simulation and I think this is a very commun scenario: let's say pc4 is the server... why I can't ping from PC1 to 192.168.2.253 (router1) but I can ping 192.168.2.2 (pc0) aren't they the same subnet? what am I missing or have to do in order to reach pc4? (192.168.100.254) from pc 1 (192.168.1.1) is there something like "default gateway" for router? thanks for advice PS: during the simulation it shows error "The routing table does not have a route to the destination IP address. The router drops the packe (from 192.168.2.253 to 192.168.1.1)"

  Read the article

• Why should I use a switched network over routed?

  - by SRobertJames

  Now that routers are affordable, why should I build a network using Layer 2 switches, which degenerate to broadcasting under poor conditions, and not just use real routing at Layer 3? Edit: Got some great replies. Let me clarify the question: Of course, at the lowest level, you want to plug your end nodes into a switch, not a router (as demonstrated by AlReece). I'm referring to switches which are used to bridge traffic between segments - that is, switches connected to other switches.

  Read the article

• How to set up a home SIP Server/Proxy for multi ring?

  - by zio

  I have a sip account which only allows one device to be registered. When i'm at home I want incoming calls to be able to ring on multiple devices. All of these devices are connected to the local network. I'm guessing the way to do this is using a local server/proxy that would allow multiple registrations which then forwards traffic to/from my sip provider. What a simple way to do this on either OS X, Ubuntu or using some low cost SIP router hardware?

  Read the article

• Routing between same network

  - by user1389735

  Hi In this scenario there is point -to point serial connection between R6 and R7 , there is router R10 whose interface F0/0 is having ip address of 10.1.1.2/24 and there is a host machine (R9) with ip address 10.1.1.1/24 which is running an application, My problem is that Application on R9 will only work when it will get its Gateway as 10.1.1.1/24 which is of router (R10) , is there any way i can make R6 and R7 transparent for R9 and R10, Or any type of routing using GRE / Route-map or any other way. Thanks in advace

  Read the article

• Why can a network address not be a valid host address?

  - by Goblinlord

  So... I have studied for CCNA and such and been working with IP networking at the least the past 8 years or so. I have always seen and been told that the network address for a subnet is not a valid host address. Now first I will start by saying I know this is true. My question is more... is there a technical reason it can not be used or was it just arbitrarily agreed upon when the specification was designed? I understand why a broadcast address can not be used (because it is ACTUALLY used). The thing is when I see a network address used it is normally only in routing which is specifically using NETWORK addresses. This being the case, (network addresses being used only when you are expecting a network address) is there some technical reason that they could not have the network address be an actual valid host address?

  Read the article

• Destination host unreachable

  - by user1010101

  I have 2 router connected to 1 switch which contains two vlans, 1 router has the ip table of vlan1 and the other router have the ip table of vlan2 I have trunked both router cable to the switch. I have set 1 ip table per router which correspond to the ip address of the PC that have this router address as a gateway. When I ping from 192.168.100.2 to 192.168.200.2 it tells me that destination host is unreachable and the message is from the router 192.168.100.1. So I guess router for 192.168.100.x does not see the router for 192.168.200.x , right ? Or am I wrong ? What are good troubleshooting steps ? http://i.imgur.com/b94Ir.png is the representation of the network, i cannot post image since im not reputated enough.

  Read the article

• MVC2 ValidationSummary and Client side Validation

  - by Raj Aththanayake

  Hi I want to have the ValidationSummary errors displayed during Client Side validation. Currently the validation messages are only appears next to the field during client side validation. I use…. MicrosoftAjax.js MicrosoftMvcAjax.js MicrosoftMvcValidation.js as my client side libraries. There is a solution for jQuery Validation Library which is in the thread… http://stackoverflow.com/questions/1724790/asp-net-mvc-validationsummary-for-client-side-validation Is there an easy way to do this? I used had xVal working DataAnnotation and it was very easy enable client side validation for the validation summary. E.g <%= Html.ClientSideValidation().UseValidationSummary("validationSummary", “Validation Errors”)% Is there way to do this in MVC2 using MicrosoftAjax?

  Read the article

• Current state of client-side XSLT

  - by Casey

  Last I heard, Blizzard was one of the few companies to put client-side XSLT into practice (2008). Is this still the case in 2011, or are more people now exploring this technique in production?  It seems that modern browsers (IE9, FF4, Chrome) and client processing power are primed to exploit this standard for tangible savings in server CPU power and bandwidth on large scale properties. Am I missing something? The negative aspects I'm aware of include * additional rendering time * additional assets required on uncached page load * additional layer of complexity * noticably less developer experience than server-side template techniques The benefits I perceive include * distributed template composition (offloaded on the client) * caching of common template fragments offloaded on the client * logical separation of document structure and data * well-documented web standard supported by all modern browsers Finally, although I know it's impossible to predict the future, I am curious to know opinions on whether or not client-side XSLT's day will come. With interest in HTML5 driving users to upgrade their browsers and developers to explore new techniques, I would say yes. How about you? Thanks in advance, Casey

  Read the article

• JMS have javax.jms.InvalidDestinationException when client stop working

  - by Tran

  I use JMS for sending requests from a client to a server. My client sends a request to the server. While the server is working with my request, my client stops (network problem) before the server finishes. When the server is finished, it'll return to the client, but the server can't see the client which sent the request to server, at which point, the server will return an exception in log file. The exception is : javax.jms.InvalidDestinationException: Cannot publish to a deleted Destination: temp-queue://ID:PC0092-49463-1344231871819-0:0:9 [^] My question is: what do I need to do in this case? Can I catch or disable this exception? And how can I do it? (Sorry, If my english is not good.)

  Read the article

• WCF client proxy initialization

  - by 123Developer

  I am consuming a WCF service and created its proxy using the VS 2008 service reference. I am looking for the best pattern to call WCF service method Should I create the client proxy instance every time I call the service method and close the client as soon as I am done with that? When I profiled my client application, I could see that it is taking lot of time to get the Channel while initializing the proxy client Should I use a Singleton pattern for the client proxy so that I can use the only once instance and get rid of the re-initializing overhead? Is there any hidden problem with this approach? I am using .Net framework 3.5 SP1, basicHttp binding with little customization.

  Read the article

• Spring MVC with a rich client framework

  - by ziggy

  I have several applications that are structured as follows DataComponent WebComponent ThickClientComponent WebServices The DataComponent has all the functionality required to access the application's data so it contains the DAOs and the JPA entities. The other three modules are: WebComponent - A spring MVC application that uses the DataComponent for data acccess ThickClientComponent- A Swing application that uses the DataComponent for data access WebServices - A SOAP based services that also uses the DataComponent. All three projets have the DataComponent as a dependeny in their Maven POM file. I would like to use a rich client framework like RichFaces, icefaces or primefaces as i need to be able to use the rich components are available in rich client frameworks (i.e. trees, panel, drag and drop etc). I have looked around and i cant seem to find an example where a Spring MVC application uses a rich client platform. Is it possible? Are the rich client platforms a framework meaning that i have to use either Spring MVC or the rich client platform but not both? The DataComponent module is spring based.

  Read the article

• "The provider is not compatible with the version of Oracle client"

  - by psyb0rg

  I just put my asp .net web service on a remote host. The service accesses an oracle db on my local machine. The service worked fine when it was running on localhost but since moving to a remote hos, I get The provider is not compatible with the version of Oracle client at Oracle.DataAccess.Client.OracleInit.Initialize() at Oracle.DataAccess.Client.OracleConnection..cctor() --- End of inner exception stack trace --- at Oracle.DataAccess.Client.OracleConnection..ctor(String connectionString) at.... I know the error is related to the data provider version running on the server/client. In my case, the only dll I referenced in the project was Oracle.DataAccess So how do I go about solving this? Note that I won't be able to change anything on the web host other than my own project. My local machine is running Oracle 11g Thanks.

  Read the article

• Jboss webservice client error

  - by user309281

  Hi I am getting following error, when a java webservice client written using jboss webservices, tries to invoke a webservice through WSDL URL. The program is executed in java 1.5 VM installed in RHEL Any idea when this kind of exception will pop up? And moreover the IP 192.168.182.20 is not of the system from which the client program executed. javax.xml.ws.soap.SOAPFaultException: [192.168.182.20] is not authorized. at org.jboss.ws.core.jaxws.SOAPFaultHelperJAXWS.getSOAPFaultException(SOAPFaultHelperJAXWS.java:84) at org.jboss.ws.core.jaxws.binding.SOAP11BindingJAXWS.throwFaultException(SOAP11BindingJAXWS.java:107) at org.jboss.ws.core.CommonSOAPBinding.unbindResponseMessage(CommonSOAPBinding.java:579) at org.jboss.ws.core.CommonClient.invoke(CommonClient.java:381) at org.jboss.ws.core.jaxws.client.ClientImpl.invoke(ClientImpl.java:291) at org.jboss.ws.core.jaxws.client.ClientProxy.invoke(ClientProxy.java:170) at org.jboss.ws.core.jaxws.client.ClientProxy.invoke(ClientProxy.java:150) at $Proxy21.send(Unknown Source)

  Read the article

• .NET/C# Drizzle database client

  - by FlappySocks

  I am planning to use Drizzle in my next C# Mono app. Since there is no C# client available for Drizzle, I thought I would have a stab at writing my own by converting the Java client, and then making it work with DBLinq. Having seen the Java client, I realise that it's a longer job that I had anticipated, and I don't have the time. Besides the Java client is not all that mature yet. Since there is an official Drizzle C client library (libdrizzle), writing a C# wrapper might be the best solution. Are there any tools available that can assist in generating the code for this?

  Read the article

• Facebook access token: server-side vs client-side flows

  - by alexey

  Facebook docs: Facebook Platform supports two different OAuth 2.0 flows for user login: server-side (known as the authentication code flow in the specification) and client-side (known as the implicit flow). The server-side flow is used whenever you need to call the Graph API from your web server. The client-side flow is used when you need to make calls to the Graph API from a client, such as JavaScript running in a Web browser or from a native mobile or desktop app. What is the difference between access tokens taken by these flows? It seems like they length differ. Can we use server-side flow token on a client? And otherwise, can we use client-side flow token on a server?

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >