Search Results

Search found 3528 results on 142 pages for 'safe'.

Page 109/142 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

• Bad Intel DQ965GF motherboard? Fails memtest, but memory is good.

  - by Boden

  I've got a machine with a DQ965GF motherboard. Two days ago it started locking up hard. Ran memtest 3.3, 1.7, and TestMem 4. TestMem just freezes, memtest failed on moving 8 bit inversions. Letting memtest run eventually causes the system to restart. I pulled memory sticks one by one, and then replaced the memory with a couple of known good sticks. No luck. I switched power supplies, didn't help. Swapped video cards just to be safe. No help. When I start the machine I get a single beep before it POSTs. According to the manual, a single beep means: 1 beep - Refresh Error (with nothing on the screen and it is not a video problem) I'm assuming that the motherboard has failed since it's obviously not a RAM or power issue. Do you agree? NOTE: I also tried resetting BIOS defaults, and even flashed the BIOS to the latest version. I also ran the Mersenne Prime Test and the CPU seems to click along just fine. (Tried logging in to superuser with openid but it's not working for me today. Hope this gets through)

  Read the article

• Thecus N5200, disk has dropped out of RAID5

  - by Anders Ekdahl

  We have a Thecus 5200 NAS here at work with five WD Caviar Black 2TB disks in a RADI5 array. Yesterday, disk 4 dropped out of the array, and in the NAS web interface there's a warning about the RAID array being "degraded". When I go into Storage - Disks, disk 1 and 4 has a warning next to them. When I click on the warnings, this information about the disks are displayed: Tray Number 4 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 34 Reallocated Sector Count 66 Current Pending Sector 1447 Raw Read Error Rate 61 Seek Error Rate 0 Hardware ECC Recovered N/A Tray Number 1 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 32 Reallocated Sector Count 0 Current Pending Sector 1465 Raw Read Error Rate 0 Seek Error Rate 0 Hardware ECC Recovered N/A I'm not really an expert on either disks or RAID arrays. Does this indicate that the fourth disk is damaged, and needs to be replaced? And what about disk number one? It has a warning, but it's still in the array. Is it safe to add the fourth disk back into the array as a spare? I can't find any way to add it back as a it were before.

  Read the article

• Windows 7 doesn't start anymore

  - by martani_net

  Hi, I've experienced some BSOD on windows 7 RC, and some freezing when startup, but today was big surprise, it doesn't start anymore. I tried to start on safe mode and no results too, it shows the starting animation, then a blue screen for less than a second and turns off immediately. The only thing I remember did today is update flash player under Firefox, then chrome stopped working even after logging off, and once restarting, it doesn't start anymore. Anyone experienced the same issue? any hints? [EDIT 3] Solved : Windows 7 have a very smart repair strategy, it works automatically, and it tried every possible fix, what fixed my problem was the system restore to a previous date, all this happened automatically. [EDIT2] these are the last lines in the ntbtlog.txt file Did not load driver \SystemRoot\System32\drivers\vga.sys Loaded driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Did not load driver \SystemRoot\System32\Drivers\NDProxy.SYS Loaded driver \SystemRoot\system32\drivers\CHDRT32.sys Loaded driver \SystemRoot\system32\DRIVERS\VSTAZL3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTDPV3.SYS Loaded driver \SystemRoot\system32\DRIVERS\VSTCNXT3.SYS Loaded driver \SystemRoot\system32\drivers\modem.sys Loaded driver \SystemRoot\system32\DRIVERS\usbccgp.sys Loaded driver \SystemRoot\System32\Drivers\usbvideo.sys [edit] this is the BSOD I get : http://twitpic.com/i87cx Thank you.

  Read the article

• Nginx : Proper use of limit_req_zone and limit_req

  - by xperator

  I have 2 website running on VPS. Their purpose is sharing music files and publishing news. Both of them use wordpress. What I am trying is that I want to prevent little hackers from flooding the webserver and putting stress on the server to make it crash. The problem is that after using limit_req_zone and limit_req my website became very slow. Browsing Wordpress control panel takes a long long time. I tried changing values but it didn't improve much. I guess the problem is Wordpress because it's the only script I am using on both front and back end. Here is the last setting which seems to be more responsive than others : limit_req_zone $binary_remote_addr zone=flood:5m rate=10r/m; location ~ \.php$ { limit_req zone=flood burst=100 nodelay; } What are the optimal values that should be used in my case (wp) ? I want the website have it's normal behavior, On the other hand stopping lifeless people from flooding. Another question, Is it safe and enough to use limit_req only on php files ?

  Read the article

• New to building computers worried about temps

  - by dave

  I'm new to building my own computers and I was wondering about maximum temperatures. I understand that the room temp can affect the computers temp but how relevent is it? I understand that if my room temp is 20°C none of my computer parts could be lower than that. But if my room is 27°C instead of 20°C would this cause my computers parts to heat up more/faster? My new computer I built myself for gaming is i7 2600k 16gb ram ddr3 1600 hd6970 2 gb 240gb ssd ( bought a nas with 3 2tb drives in raid 5 for my home network ) 850w modular psu I also have my old hp computer i3 2120 8gb ram hd6770 1tb hdd I also have 3 laptops in my household, but I am not worried about their temps, they heat up my legs but they are never under stress. Due to size and money reasons I used an old case and it only has one of the sides left on it. Is this bad for the computer and will the extra dust cause problems? Or should I leave it this way or take the missus wrath and buy a case? If so is there any certain case I should get? I don't care about looks I just want card reader and usb slots and for it to run as cool or cooler than now, my case has 1 fan. Also what are the max temps for my new and old computer parts? Is 40°C under load ok for my CPU, what about 70°C for my GPU is that ok too, or should I worry? What are normal and safe temps for my components? I have looked around but there seem to be lots of different answers. I know that 100°C is bad but I want my parts to last as long as possible and this site always seems to give good replies without arguing or flaming.

  Read the article

• Setting up a network where packets are traced

  - by Marcus

  My situation is the following: I have an internet connection, which is shared between people. More or less obviously, people is using it to download illegal stuff. Since I'm the owner of the connection, I want to avoid being sued. I don't want to prevent the people from doing the things they want, but I want to be legally safe. Now, I have relatively little competences in network administration, so I was wondering: is it possible to setup a network, where the source and destination of the packets are logged? I would use this to prove, in case of lawsuit, that the traffic was coming from a given machine. if the idea is feasible, is there any wireless router on which I can install linux, where I can install the packet sniffer? how much space could the logs take (containing only the timestamp/source/destination), per GB of traffic? a very rough estimation would be very helpful. if a machine on my network is sending bittorrent packets to a certain IP, would this log be able to reflect the time, source ip and destination ip? I assume that obviously the torrent data would be encrypted and un-decryptable. Am I missing something? Is there a better strategy? Any pointer to documentation would be helpful as well - in that case, I would use this as starting point.

  Read the article

• Automate creation of Windows startup script?

  - by Niten

  Is there a good way to automate installing local startup (rather than login) scripts in Windows XP and Windows 7, via the command line, WMI, COM, or otherwise (even Win32 if it comes to that)? I need to setup a local startup script on a large number of computers, and unfortunately, Active Directory is absolutely not an option. I would like to write a script or small program that I can run on each computer to perform the startup script installation in order to save myself a lot of error-prone point-and-click manual labor. I see that when one uses gpedit.msc to create a local startup script, information about the script gets stored in the registry here: HKLM\Software\Policies\Microsoft\Windows\System\Scripts\Startup However, if you create such a script and then delete its registry key, the script will remain listed in the local Group Policy editor; as is so often the case in Windows, apparently there is more going on there than meets the eye. This leads me to question whether it's safe to manually add subkeys for new startup scripts here (I wouldn't want my script to be overwritten by later changes made using the local Group Policy editor, for instance)... Another option that's occurred to me is to create an item in the Task Scheduler configured to run at system startup. However, my concerns there are twofold: Can this be automated any more easily? For instance, the at command doesn't appear to let you schedule a task for system startup, and WMI's Win32_ScheduledJob interface looks unreliable (it fails to show any of my currently scheduled tasks, for one thing). Would I be able to prevent users from logging in until the scheduled startup task is completed, as can be done with "normal" Windows startup scripts? Thanks in advance for any suggestions, I've been banging my head against this one for a bit...

  Read the article

• Win7 System folder contains infinitely looping SYSTEM(!) directory

  - by Matt

  My Windows 7 Enterprise computer has been crashing fairly frequently recently, so I decided to boot up in safe mode and run the TrendMicro client I have installed. It froze about 10 minutes into the full system scan, so in the spirit of http://whathaveyoutried.com, I started scanning each folder individually. When I got to ProgramData, the AV failed with an uncaught exception. I then went down a level and tried scanning Application Data, which failed as well. Imagine my surprise when I open the folder just to see the same folder again! As far as I can tell, this folder loop continues indefinitely. (If you are trying to recreate this, keep in mind that ProgramData is a hidden folder.) I'm actually a bit concerned that these are system folders, as this is a brand-new computer with a clean installation. I guess I have three questions: Has anyone else seen/experienced this before? I'm running Win7 SP1. How do I fix this? I've run CHKDSK \F with no success (although it was incredibly slow). What are the ramifications of an infinitely recursive directory? Theoretically speaking, each link takes up memory, so shouldn't I have no space available on my hard drive? (I've got about 180GB left.) I noticed that the tree view on the left only shows the "linked folder" icon on the deeper folders--does this mean anything special? (I've circled the icons or lack thereof in red.) How can the OS even resolve this aberration? And above all, what would happen if I were to select "Expand all folders"??? :P Matt

  Read the article

• I have enabled hidden administrator in Win 7 home, but programs still dont work.

  - by Angela

  I have Windows 7 Home Premium, and would like to do some maintenance tasks such as running Disk Defragmenter. However, this and other programs and applications that I'm accustomed to using are now blocked. For these programs, there is a shield icon next to their icons and nothing happens when I click on them. I notice that the screen blinks slightly, but I do not get prompted for a password and the program still does not run. It seems these programs may only be accessible through an Administrator account. However, right-clicking and selecting "Run As Administrator" does not work. After some research, I found a way to enable the hidden built-in Administrator account. I booted the computer into safe mode. In the command prompt, I typed net user administrator /active:yes. I gave the account a password. I rebooted the system. There is now an Administrator account on the home screen. However, the locked programs behave no differently for me when I use this account. What could cause this problem? How can I fix it?

  Read the article

• How to place a virtual machine in DMZ?

  - by Giordano

  I have an Ubuntu 12.04 server running few virtual machines with KVM. I would like to expose some of these virtual machines on the internet, to make it possible for customers to test the products we're developing and make available other products for demo purposes. One of the server NICs is configured with a public IP. However before exposing anything on the web I would like to be sure that if one of the virtual machines get compromised, the attacker doesn't reach the rest of the hosts. What I would like to do is to put these virtual machines into a DMZ. These are the steps I'm planning to do: Create a tap interface in the virtualization host (let's say tap1) Create a bridge using tap1 and give it an IP in a subnet separate from the other hosts. Let's say 10.0.0.1 Attach the DMZ virtual machines to the bridge and configure their IP statically (10.0.0.2, 10.0.0.3, etc...) Using UFW, forbid any traffic from 10.0.0.0/24 to any of the internal hosts, allow the traffic from the internal hosts towards 10.0.0.0/24 and expose the virtual machines on the web using port forwarding. Do you think this setup is safe? Can you suggest any improvement or a better/safer approach? Thanks in advance!

  Read the article

• Linux - preventing an application from failing due to lack of disk space [migrated]

  - by Jernej

  Due to an unpredicted scenario I am currently in need of finding a solution to the fact that an application (which I do not wish to kill) is slowly hogging the entire disk space. To give more context I have an application in Python that uses multiprocessing.Pool to start 5 threads. Each thread writes some data to its own file. The program is running on Linux and I do not have root access to the machine. The program is CPU intensive and has been running for months. It still has a few days to write all the data. 40% of the data in the files is redundant and can be removed after a quick test. The system on which the program is running only has 30GB of remaining disk space and at the current rate of work it will surely be hogged before the program finishes. Given the above points I see the following solutions with respective problems Given that the process number i is writing to file_i, is it safe to move file_i to an external location? Will the OS simply create a new instance of file_i and write to it? I assume moving the file would remove it and the process would end up writing to a "dead" file? Is there a "command line" way to stop 4 of the 5 spawned workers and wait until one of them finishes and then resume their work? (I am sure one single worker thread would avoid hogging the disk) Suppose I use CTRL+Z to freeze the main process. Will this stop all the other processes spawned by multiprocessing.Pool? If yes, can I then safely edit the files as to remove the redundant lines? Given the three options that I see, would any of them work in this context? If not, is there a better way to handle this problem? I would really like to avoid the scenario in which the program crashes just few days before its finish.

  Read the article

• DDoS nulling to some ips and other options?

  - by Prix

  I am looking for some information in regards DDoS in the follow scenario: I have a server that is behind a Cisco Guard and it will be DDoS'ed, I only care about a set list of IPS that by not means are the attackers. Is it possible to null all other ips but this list to actually get any response to my server or in the long run no matter what I do if they have enough DDoS power I will just go down like a flie ? Is there any recommended company out there that can actually cope with a DDoS ? My server will mainly run several clients that will get connected to a external server and all it needs access to is my local MySQL the the private network so I can access it. There will be no other services runnings such as web or ftp etc at least not to the external ips of the server if i ever have to have any of these service they will be on the private network. The MySQL will be available externally only to 1 safe ip not known by anyone but me and internally at localhost + private network. Are there any solutions ?

  Read the article

• What are the "least legally restrictive" well-connected countries to host a website?

  - by monster

  NB: I am aware that this question is subjective, as it can't be defined precisely, but the answers should still be "objective": Country name, and what makes it legally safer. EDIT: A) I am located in Germany. B) I am NOT looking for a place to offer pirated Software/Media; no binary on my site, except "profile icon". Hello! I want to start publishing "social" websites / apps, and I found that the biggest initial problem is this: Any and all services I have to depend on, including Domain Registrar, DNS provider, Server/Cloud Provider, CDN Provider, ... even my Insurance Agent, basically say that they can "throw me out" if my website contains "unacceptable" content. It's always phrased in such a way that basically anything can fall under "unacceptable" content. This is very frustrating because you just can't fully control what users post on your "social website", and you so you basically have to expect when you go to bed that your site is going to be gone when you wake up. I've heard a lot of horror stories about this. Since the "Terms Of Service" of all those providers are foremost to protect themselves from legal actions, and those legal actions depend on the country where they are located, it seems like the first step is to find which country is the "safest" to locate a site. "Safest" being defined as, where I am least likely to get in legal trouble with the local authorities, if some user posts something unacceptable in some way. The main restriction is that it should also be a "well-connected" country, because there is no point in being "safe", if my users can't get to my sites, or the latency is unacceptable. I am targeting the English speaking people in any country as my future users.

  Read the article

• Installed Paragon HFS+ for Windows 8, now my pc won't recognize the external firewire drive

  - by Steve

  I'm not incredibly knowledgeable about computers and I really need some help. Just got a Seagate external firewire drive this morning. I downloaded the necessary pc driver (Paragon HFS+ for Windows 8) through their website per the instructions that came with the drive. After installation, I restarted and the pc recognized the firewire drive just fine. About three hours into copying files from my pc to the firewire drive, it gave me an error and told me the files couldn't be copied. When I clicked to get out of the message, the computer crashed. After an hour of it trying to repair itself in safe mode, it restored me to an earlier version before the system crashed. Here's my current dilemma: The Paragon HFS+ is still showing up in my programs as installed, but the Device Manager is not recognizing the drive. When I try to uninstall and reinstall Paragon, it interrupts me with a message saying "The setup must update files or services that cannot be updated while the system is running" and basically gives me the finger. I have no idea what to do now, as it won't let me uninstall and reinstall Paragon, and I have no idea why it crashed my computer in the first place. Is there possibly another Mac - PC firewire driver I can try downloading instead? I really don't know what I'm doing and any help would be greatly appreciated.

  Read the article

• How to share text, pictures and video to restricted set of users

  - by joaoc

  I want to share pictures and videos of my kid growing up but I don't want it to be open to the public. I just want me and my wife to be able to add material and then share with grandparents and friends who would be given a username/password or some other solution that authenticates them. This content would preferably be available remotely over the internet or downloaded periodically to the allowed viewers computers. The second option most likely means they would have to install a client, which I am not too fond of doing (I would have to ask them to install it, help configure for different platforms, ...) I'm at the start but I would like software that also allows export of the data (if one day I want to migrate to a different solution). Folder sharing I don't know if Windows folder sharing is reliable, robust and safe enough to share over the internet. Dropbox could be a software solution, but it's limited to 2GB and requires receivers to also install and configure software. A folder is just a collection of files, so it would be harder to keep them organized with text describing the pictures/video Email I could email the content every now and then but videos are almost always too big to go as attachments This would also not provide a history of updates to anyone just recently joining in Are there other solutions to achieve this? NOTE: I also thought that software to run a local or remote blog could be an option but we aren't allowed to ask those questions on superuser because one admin doesn't like cloud-computing questions. But if you do think it's the best approach and can suggest a solution, do state it in the answers anyway!

  Read the article

• Outlook 2010 on WinXP runs once then refuses to run again until reboot

  - by msorens

  Since I installed Outlook 2010 on a new machine (WinXP Pro SP3) a couple months back I have had an issue that is quite annoying: If I close Outlook then attempt to restart it I get a small pop-up saying only: "Cannot start Microsoft Outlook". I found one workaround, but not a terribly practical one: reboot. If I reboot then launch Outlook, it opens fine. Here is what I know: Since I can run Outlook just fine after a reboot, I do not see that a system restore, an OS reinstall, or the like would help. I tried "outlook.exe /resetnavpane" and "outlook.exe /safe" but those give the same error. There are no entries in the event log. There is no instance of Outlook appearing in the process list once I close the program, so it does not seem to be an alias for "outlook is already running". As far as I have found, my situation is unique among reports of similar incidents: I have uncovered no other reports saying Outlook would run fine the first launch or that a reboot would again allow it to run. Suggestions?

  Read the article

• Road Warrior VPN Setup

  - by wobblycogs

  I apologise up front for the rather open ended nature of this question but I've got well out of my depth and could really do with some pointers. I need to set up a road warrior VPN solution which will allow our customers to securely access a number of services we provide for them. Customer machines will be running a variety of Windows versions from XP onwards with a variety of patch levels. Typically they will connect from the clients main offices but not always. It is safe to assume that all clients will be behind NATs but we may occasionally see a connection that isn't NAT'ed. Typical connection situation is therefore: Customer Laptop -- Router (NAT) -- Internet -- VPN Server + Firewall -- Server (Win 2008 R2, Non-routable IP) There will initially be a dozen or so people that could connect but that will grow quickly to around 100. It's unlikely that we'll see that many concurrent connections though, I imagine our total VPN throughput would be <50Mbps peak. What are my options for setting this up? I've been trying to set up a system like this using a MikroTik router for a few days but have struggled to get it working correctly, particularly with NAT'ed clients. I've had a quick look at OpenVPN and liked what I saw but I think it's unlikely our customers IT departments would allow the client to be installed. Finally I've looked at the Cisco ASA range but I'm on a fairly tight budget so this is less preferable but it looks like it would work pretty much out of the box. My fall back position is to connect the server directly and use the provided VPN + Firewall facilities but that is far from ideal as the number of servers is likely to grow over time.

  Read the article

• Weirdly high ping on direct ethernet connection?

  - by Antriel

  I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms. I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms. I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN). Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't help. I tested it in the safe mode with networking, same problem there. It slows down our client-server based programs and I have no idea what's causing it. All I could google up was that disabling Interrupt Moderation would help, it didn't though. Anyone had similar problems? tl;nr: Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.

  Read the article

• Reducing both pagfile.sys and hiberfil.sys in Windows 7

  - by greenber

  I recently used Defraggler to consolidate my free space areas on my D: drive preparatory to using Disk Manager to break my drive into two areas, one as my "data area" for Windows 7 (normally on my C: drive) and to experiment around with Windows 8. The Defraggler program works so well I ran it on my C: drive and I ended up with a lot of free space both on my C: drive and my D: drive. I was very happy. And then I woke up the next day and I've got virtually no free space left, something like 8 MB on my C: drive and about 3 GB on my D: drive. I then ran Wintree (which gives a nifty graphical representation of disk usage) and found I had a large page file and a large hiberfil. So I temporarily turned off hibernate and reduced the page file size to 2000megabytes and then rebooted so that both would take effect. It had no effect on the C: drive or the D: drive. That makes no sense to me. What caused the free space on each drive to disappear, why doesn't the page file size being reduced and the hibernate file being turned off free up disk space to either the C: or the D: drive? Would it make sense to delete the two files in question and, if so, how do I go about doing that? Safe mode? Thanks. Ross

  Read the article

• How to stop Firefox on an SSD from freezing when using the search box or submitting a form?

  - by sblair

  Firefox usually freezes for about a second whenever I search for something from the toolbar search box, when submitting a form, or when clearing the search box history. I suspect it has something to do with the auto-complete feature. Using Windows 7's Resource Monitor, the problem seems to be from the file: C:\Users\<username>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\formhistory.sqlite-journal I believe this is a temporary file which caches database writes. The following screenshot shows the very high response times from six different searches, and that the queue length on drive C shoots off the scale: My Firefox profile is on an Intel X25-M G2 SSD. The problem doesn't seem to occur if I create a new profile on a hard disk drive. However, I'd like to know why the problem exists on the SSD in the first place (because it's an annoying problem which contradicts the reason I bought an SSD, and it might happen with other applications too), and how to prevent it. It still occurs if Firefox is started in safe mode, and with the recent beta versions. Updates: VACUUMing the Firefox profile databases does not help with this problem. The SSD Optimizer in the Intel SSD Toolbox does not help either.

  Read the article

• Is a Hyperthreaded CPU more powerful and more efficient than a Dual-core CPU? [closed]

  - by user1811864

  which computer to choose with Pentium processor hello they are getting rid of the old computer equipment in the office and i have to choose the computer to take home i get first choice to pick. -15 inch lcd screen 4 gb of ram core 2 duo dual Core E8400 3.00 GHz dvd writer windows vista/ linux -15 inch crt monitor with 2 gb ram and pentium 4 2 ghz single core HT technology windows xp hardisks both 250 GB my friend is telling me to choose the second one Pentium single core HT because he told me it runs faster becuase of HT technology and cooler and consumes less current electricity so it wont get overheated because it has HT technology so it's high definition for encoding and watching HD movies and HD sound and is like a gaming pc to play internet games. And also he said the dual core 8400 runs at 3 ghz compared to the 2 ghz so it heats very much because of the two extra cores so it takes more current raising electricty bills and is not good for gaming and watching HD movies and internet flash animations and games because of getting heated everytime. And he wants to choose and take the E8400 because he has air conditioning at home so it will be safe from heating. So which one computer should i take is it really faster because of the HT High definition technology and will i be able to play internet flash card games better and watch good HD movies Youtube etc and play all the music and songs.

  Read the article

• Connecting to unsecured wireless network

  - by Sanchez

  I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

  Read the article

• Does Antivirus2009 or Antivirus360 automatically install on your computer and if so how?

  - by sergey

  I run Firefox on Vista, and unfortunately I got tricked (through a deceptive google result) into going to a page containing one of those fake "Your Computer Has all of this Spyware on it!" pages. I tried manually closing the tab, but it had a "Are you sure you want to navigate away" JavaScript alerts (HATE THOSE). So I clicked "OK," and the tab closed. Then I closed firefox altogether and rebooted. Now, before I could close the tab, it did prompt me to download a file, but of course I choose not to, and checking my downloads folder, nothing new is there. Also, even if I ?did? download it, ?I? would still have to choose to run it by double clicking on it for it to install itself, right? Also, I ran Malware Bites and Windows Defender and both said everything was fine. From this I would normally believe I am safe, but I have read everywhere that this thing "automatically installs" itself and that it is a bitch to get rid of. Is it really possible for this thing to dig in if you are running firefox and didn't choose to download it or run it after downloading?

  Read the article

• Cloned Win7: Keyboard doesn't work

  - by Marc

  I cloned my old Windows7 hard disk to a shiny new Seagate Momentus XT 500GB using the free EaseUs Disk Copy tool on my laptop. After the clone process I used the Windows 7 installation disc to start the automatic startup repair. This took maybe 15 minutes and then my cloned disk was able to start. Now the cloned disk boots until the login screen and then I can't do anything because my keyboard just doesn't work. I tried connecting an external USB keyboard but this didn't help. The mouse is working fine. Note that the keyboard works fine in BIOS and in the Windows startup options menu. I booted into safe mode and again the keyboard is not working at all. I also noticed that the letters "Press CTRL+ALT+Delete to login" are now shown in italic font but they used to be shown non-italic on the original disk. I have now replaced the clone with the original disk again and from here everything works fine. Doesn't anybody have an idea how I can get my keyboard back?

  Read the article

• Windows Update and lsass.exe

  - by David

  I have a brand new installation of Windows XP (SP1 or older). I installed Norton AntiVirus, Firefox, Putty, and Cygwin. No other software is present. Windows Update finds the following 64 updates: KB905760, KB978262, Internet Explorer 8, KB71961, KB954155, KB968816, KB923561, KB950762, KB949402, KB950974, KB951376, KB951748, KB952004, KB952954, KB955069, KB956572, KB956802, KB956803, KB956844, KB958470, KB958869, KB959426, KB960803, KB960859, KB961501, KB969059, KB970238, KB970238, KB971032, KB971468, KB971657, KB972270, KB973507, KB973815, KB973904, KB974112, KB974318, KB974392, KB975025, KB975560, KB975561, KB975713, .......) When these updates are applied, the system reboots to a black screen with two error messages. The first error message says: lsass.exe - Application Error The application failed to initialize properly (0xc00000142). Click on OK to terminate the application. The second error message says: services.exe - Application Error The application failed to initialize properly (0xc00000142). Click on OK to terminate the application. I then proceed to boot into Safe Mode, use System Restore, and everything works fine again until the 64 updates re-appear in Windows Update. I can see two options: disable Auto-Updates or install each of the 64 updates one at a time until finding the troublesome update. Does anyone have any better ideas?

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >