Search Results

Search found 11930 results on 478 pages for 'shared machines'.

Page 109/478 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

• Disable or remove filter driver for single HID device

  - by snoopen

  Running Windows XP in a corporate setting here. I have an issue where a filter driver is interfering with the functionality of different USB HIDs. For example graphics tablets do not respond while the filter driver is in place. I've also had the issue with foot pedals used with transcription software. My question is really two fold: A) what makes Windows use a filter driver on one HID but not another? B) when a filter driver is causing conflicts how can I disable it on the affected devices? Background I've previously narrowed down the issue to the filter driver by uninstalling the software (Funk Proxy Host) responsible for the filter driver. The software is a type of RDP we use here at work. (I might have even booted into safe mode and renamed the file, I forget). I believe the filter driver is present to disable or modify the use of the local keyboard and mouse while admin staff are assisting users. Either way I don't have the authority to just go uninstalling this software. As far as I can tell the software versions are the same, however I'm not sure if the device driver definitions are all the same as I don't know where these things would be located. To check for the presence of the filter driver I locate the hardware device in Device Manager, click Properties Driver tab Driver Details.... It shows up as ph32ihid.sys. Even though all machines are meant to have the same SOE and do have Funk Proxy Host installed I don't always have issues with the same HIDs. A few machines here the foot pedals without any issues. I've not had any machines work with the graphics tablet without uninstalling Funk software. Driver details I've just read up a bit more about filter drivers and found the drivers description in the registry under "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\ProxyHostHIDFilter" There it's called "Kernel-mode HID filter driver for the Proxy Host". Presumably I could also disable it here but that would be system wide which is probably not desirable?

  Read the article

• VMWare Workstation 8 Disk I/O & Hard Faults

  - by Scott

  I have VMWare Workstation 8 installed on a host machine with the following specs: Intel i5 2500k CPU 16GB DDR3 1600 ram 1TB Western Digital Caviar Black HD I have two Windows 7 virtual machines configured (currently running one at a time but will be operating both at once when my 32GB RAM kit arrives in a couple days). Each one is configured with 8GB of RAM and no tweaks/performance customizations or anything done. All of the VMWare settings are the defaults. When I boot into these machines and run various programs (Visual Studio, Outlook, etc), I can hear the disk thrashing quite a bit and checking Resource Monitor, I can see that I'm getting anywhere between 300-800 hard faults per second. From the host machine, it shows they're coming from the VMWare image. If I go to the virtual machine, whatever app I'm currently loading is the image that's causing the hard faults. As I understand it, hard faults are (simply) when an address in memory has been swapped out to the page file and has to be read from the page file instead of from memory. I don't understand why this is happening though. With 8GB of ram on the guest machine and 6.5GB available, what could be causing this? I know Windows 7 supposedly improved on page file management over XP but it seems excessive for this kind of slowdown, disk thrashing and high hard fault count when I have that much free RAM. Is there anything I can to to improve the performance in my guest machines? On the host machine, I can open/run any applications at all and hard faults stays around 0 with low disk I/O.

  Read the article

• creating a backup system with freenas

  - by masfenix

  We are currently in the process of opening a new accounting firm in the new year (actually moving from our previous location). I am looking for a cheap/free solution to back up our files (small, text files couple of kb). I was impressed with FreeNas and Windows Backup but I found out that Windows Backup only saves for a maximum of 2 years. The work machines will be running Windows 8 or Windows 7. There can be many work machines however we have only one to start with (ie, think of it as just one employee). I have an old core 2 duo with 2 gigs of ram that I can convert to a server if need be. I want the syncing to be done through LAN since the data is confidential and should never touch the outside world. So ideally, I would like the following scenario: A skydrive/dropbox like service to sync my client files over work machines and a central server. The "server" part should store history of files (i don't know how this will be done since the file will have the same name?). This isn't really necessary, but I can see it become useful. I am not familiar with RAID, so does any software RAID solution exist? I will most likely be buying 2 hard drives.

  Read the article

• Windows Server Connected to Domain Without Being Domain Controller

  - by saluce

  Can a Windows Server be connected to an Active Directory domain without being a domain controller? Here's the scenario: I want to use Windows Server 2012 to run several virtual machines for testing our web application in a variety of environments. We have a corporate domain, and I'd like to use the corporate login (or at least a common login) on each of the virtual machines without necessarily having to get IT to set up each virtual machine on the corporate domain. Also, I need the server itself to be able to authenticate domain logins (the app uses domain login information for users to login). However, I absolutely do NOT want it to be a DC on the corporate network. Thus, my questions: Can a Windows Server be connected to an Active Directory domain without being a DC? Can a Windows Server authenticate users on another domain without being a part of that domain? Can a Windows Server be a domain controller in a small network (comprised of just the server and itself) and use the corporate domain's Active Directory for authenticating user logins to the server, the web app, and the virtual machines?

  Read the article

• SVN client too old after I used sshfs

  - by johnlai2004

  I have a svn checked out web application on a shared hosting linux server. The linux server has an svn client that I can access via ssh. From my localhost, I did the following > sshfs [email protected]:webappdir/ /media/webapp > cd /media/webapp > svn update svn: Working copy '.' locked svn: run 'svn cleanup' to remove locks (type 'svn help cleanup' for details) > svn clean up It's been 15 minutes and the svn clean up still isn't finished. I think it may have froze. So then I did the following: > ssh [email protected] > cd webappdir > svn update svn: This client is too old to work with working copy '.'; please get a newer Subversion client So now I can't update my webappdir because my /media/webapp is stuck on svn clean up, and my shared hosting server's svn client is out of date. I don't have privileges to install a new svn client on the shared hosting server. How do I get my svn update to work?

  Read the article

• Offloading backups to secondary network

  - by user1467163

  I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

  Read the article

• How to disable Utility Manager (Windows Key + U)

  - by Skizz

  How do I disable the Windows + U hotkey in Windows XP? Alternatively, how do I stop the utility manager from being active? The two are related. The utilty manager is currently providing a potential security hole and I need to remove it[1]. The system I'm developing uses a custom Gina to log in and start a custom shell. This removes most Windows Key hotkeys but the Win + U still pops up the manager app. Update: Things I've tried and don't work: NoWinKeys registry setting - this only affects explorer hotkeys; Renaming utilman.exe - program reappears next login; Third party software - not really an option, these machines are audited by the clients and additional, third party software would be unlikely to be accepted. Also, the proedure needs to be reasonably straightforward - this has to be done by field service engineers to existing machines (machines currently in Russia, Holland, France, Spain, Ireland and USA). [1] The hole is via the internet options in the help viewer the utility app links to.

  Read the article

• How do I start the Workstation Service so I can use `net use`?

  - by nitefrog

  I have a Windows 7 machine that logs into a domain. The machine can net view and see the different shares, but when I try to use, net use * \\name\share, I get an error stating that the service is not started. Yet when I issue a net start, it states the service is already started. My other win7 machines work fine; they can see and use any of the shares. Is there a security setting that needs to be disabled or enabled? I really need to get this working, and I have no other ideas as the other machines have no problem accessing the shares on different systems. The error I am getting is , "The Workstation Service Has Not Been Started", but like I said other machines can connect fine, and when I issue a, "net start workstation", it states the service is already started. In addition the error number I am receiving is 2138. UPDATE: On the machine that is having issues. From the troubled machine if I issue a Net View \\name I can see all the shares on the machine I want to connect to. When I try to net use * \\name\sharename I get the error The Workstation service has not started. I have set both settings sc config lanmanworkstation start = auto and sc config lanmanserver start = auto on the Windows7 computer that is having issues. I have rebooted the computer and still no dice. I can net view any computer on the network and see all shares, but I cannot access any of the shares in which I can see. In the registry under the HKLM\System\CurrentControlSet\Services Both LanmanServer and LanmanWorkstation start is set to 2. Screen capture of net use and view: The Services: This is really weird. What am I missing? It has to be a security setting...

  Read the article

• Convention location for JAR files for a LaunchDaemon on OS X?

  - by Barry Wark

  I'm setting up a Hudson build slave on an OS X machine. I'm using launchd to start the slave using the following plist in `/Library/LaunchDaemons/': <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>KeepAlive</key> <true/> <key>Label</key> <string>org.hudson-ci.jnlpslave</string> <key>ProgramArguments</key> <array> <string>/usr/bin/java</string> <string>-jar</string> <string>/Users/Shared/Hudson/slave.jar</string> <string>-noCertificateCheck</string> <string>-jnlpUrl</string> <string>file:///Users/Shared/Hudson/slave-agent.jnlp</string> </array> <key>RunAtLoad</key> <true/> </dict> </plist> I'm currently putting the slave.jar and slave-agent.jnlp files in /Users/Shared/Hudson but this seems like an unnecessarily user-visible location. What's the convention? Where should I be putting these JARs for a daemon?

  Read the article

• FreeBSD: problem with Postfix after updating LDAP

  - by Olexandr

  At the server I installed openldap-server, at this computer open-ldap client has already been installed. Version of openldap-client (2.4.16) was older then new openldap-server (2.4.21) and the version of client has updated too. OpenLDAP-client works with postfix on this server and after all updates postfix cann't start again. The error when postfix stop|start is: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix" At the category with libraries is libldap-2.4.so.7, but libldap-2.4.so.6 is removed from the server. When I want to deinstall curently version of openldap-client, system write ===> Deinstalling for net/openldap24-client O.K., but when I start "make install" system write: ===> Installing for openldap-sasl-client-2.4.23 ===> openldap-sasl-client-2.4.23 depends on shared library: sasl2.2 - found ===> Generating temporary packing list ===> Checking if net/openldap24-client already installed ===> An older version of net/openldap24-client is already installed (openldap-client-2.4.21) You may wish to ``make deinstall'' and install this port again by ``make reinstall'' to upgrade it properly. If you really wish to overwrite the old port of net/openldap24-client without deleting it first, set the variable "FORCE_PKG_REGISTER" in your environment or the "make install" command line. *** Error code 1 Stop in /usr/ports/net/openldap24-client. *** Error code 1 Stop in /usr/ports/net/openldap24-client. Updating of ports doesn't help, and postfix writes error: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix"

  Read the article

• 2012 R2 services will not start after promotion to Domain Controller

  - by Cybersylum

  Having a peculiar issue promoting a Windows 2012 R2 server in a domain at 2003 domain/forest functional level. Built a new 2012 R2 server, added the following software (labtech, appassure, eset A/V, & Teamviewer). It activated and appeared to be working fine. I added the Active Directory Domain Services role, and completed the configuration (Domain/Forest Prep, and DC promotion). All appeared to go well. I rebooted the server, and that's where the peculiar stuff began. I noticed the server indicated it needed activated again; but would not accept the key. I verified the key was good. That's when I noticed the Software Protection service (as well as many other core services - Base Filtering engine, DHCP client, firewall, etc) would not start. The error message for all of them was "Access Denied". I called MS, and they wanted to troubleshoot at a service level. Their fix was to use procmon and identify the resource that needed permissions (registry key, file or folder) and add "everyone" with full control). That got the services to start; but the problem re-appeared after a reboot. Thinking the issue might have been with the anti-virus package during the promotion process, I rebuilt the DCs from scratch and removed the metadata from AD (as I could not demote the machines "rpc server unavailble"). I tried to promote the newly built machines again. The only changes to the brand new machines being critical updates. Again the promotion appeared to work fine; but upon reboot (and a long wait to allow replication to occur) similar problems began to re-appear. I have verified that the schema updates are correct (schema version is 69 - for Windows 2012 R2). I am not finding much about this issue through my own searches, so I thought I would post this to see if anyone else has seen anything similar...

  Read the article

• VMware Workstation Bridged Network Host UnReachable

  - by user2097818

  VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

  Read the article

• Strange File-Server I/O Spikes - What Is Causing This?

  - by CruftRemover

  I am currently having a problem with a small Linux server that is providing file-sharing services to four Windows 7 32-bit clients. The server is an AMD PhenomX3 with two Western Digital 10EADS (1TB) drives, attached to a Gigabyte GA-MA770T-UD3 mainboard and running Ubuntu Server 10.04.1 LTS. The client machines are taking an extremely long time to access/transfer data on the file server. Applications often become non-responsive while trying to open files located remotely, or one program attempting to open a file but having to wait will prevent other software from accessing network resources at all. Other examples include one image taking 20 seconds or more to open, and in one instance a user waited 110 seconds for Microsoft Word 2007 to save a document. I had initially thought the problem was network-related, but this appears not to be the case. All cables and switches have been tested (one cable was replaced) for verification. This was additionally confirmed when closing down all client machines and rebooting the server resulted in the hard-drive light staying on solid during the startup process. For the first 15 minutes during boot, logon and after logging on (with no client machines attached), the system displayed a load average of 4 or higher. Symptoms included waiting several minutes for the logon prompt to appear, and then several minutes for the password prompt to appear after typing in a user name. After logon, it also took upwards of 45 seconds for the 'smartctl' man page to appear after the command 'man smartctl' was issued. After 15 minutes of this behaviour, the load average dropped to around 0.02 and the machine behaved normally. I have also considered that the problem is hard-drive-related, however diagnostic programs reveal no drive problems. Western Digital DLG, Spinrite and SMARTUDM show no abnormal characteristics - the drives are in perfect health as far as the hardware is concerned. I have thus far been completely unable to track down the cause of this problem, so any help is greatly appreciated. Requested Information: Output of 'free' hxxp://pastebin.com/mfsJS8HS (stupid spam filter) The command 'hdparm -d /dev/sda1' reports: HDIO_GET_DMA failed: Inappropriate ioctl for device (the BIOS is set to AHCI - I probably should have mentioned that).

  Read the article

• How can I start hostednetwork on Windows 7?

  - by Pirozek

  When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

  Read the article

• One workstation gets slow access to the server, but others are fast

  - by Mike Hanson

  I've just setup a machine with Windows Server 2008. It hosts various services, like IIS, POP3, SMTP, Music for Squeezeboxes, VNC. All was working well for the first week or so. One day I needed to create a mapped drive on the server, so it could access files on my workstation. Windows indicated that Network Discovery was needed, so I turned it on with the "Home / Office" option (rather than "Public"). This may be coincidence, but since that time I've been having troubles accessing various services from my main workstation (running Windows 7/64): POP3 continued working correctly, but SMTP was delayed or failed entirely. (Telnet took 20 seconds to connect, but Outlook would never send messages.) VNC failed entirely. I reinstalled it on the server, and now it works but feels sluggish. The music web server was extremely delayed and usually failed. I tried reinstalling, and now it takes about 30 seconds to show the page name on the browser tab, and another 30 seconds to display any page contents. Other machines on the local network seem fine, as do machines connected via the Internet. I don't believe I changed anything on my own machine that would cause this. I considered the possibility that my anti-virus was involved, so I uninstalled AVG (commercial version), but that didn't help. I installed Norton 360 after that, and it didn't complain of viruses on my machine, and the delays remained. Because only my machine is affect, I'm tempted to blame it, except that reinstalling software on the server improved the situation, so there is almost certainly something going on with the server too. The firewall has all the necessary ports open, and it works fine for the other workstations (including external machines connected via the Internet), which indicates that it should be OK. Any ideas?

  Read the article

• Servers - Buying New vs Buying Second-hand

  - by Django Reinhardt

  We're currently in the process of adding additional servers to our website. We have a pretty simple topology planned: A Firewall/Router Server infront of a Web Application Server and Database Server. Here's a simple (and technically incorrect) diagram that I used in a previous question to illustrate what I mean: We're now wondering about the specs of our two new machines (the Web App and Firewall servers) and whether we can get away with buying a couple of old servers. (Note: Both machines will be running Windows Server 2008 R2.) We're not too concerned about our Firewall/Router server as we're pretty sure it won't be taxed too heavily, but we are interested in our Web App server. I realise that answering this type of question is really difficult without a ton of specifics on users, bandwidth, concurrent sessions, etc, etc., so I just want to focus on the general wisdom on buying old versus new. I had originally specced a new Dell PowerEdge R300 (1U Rack) for our company. In short, because we're going to be caching as much data as possible, I focussed on Processor Speed and Memory: Quad-Core Intel Xeon X3323 2.5Ghz (2x3M Cache) 1333Mhz FSB 16GB DDR2 667Mhz But when I was looking for a cheap second-hand machine for our Firewall/Router, I came across several machines that made our engineer ask a very reasonable question: If we stuck a boat load of RAM in this thing, wouldn't it do for the Web App Server and save us a ton of money in the process? For example, what about a second-hand machine with the following specs: 2x Dual-Core AMD Opteron 2218 2.6Ghz (2MB Cache) 1000Mhz HT 16GB DDR2 667Mhz Would it really be comparable with the more expensive (new) server above? Our engineer postulated that the reason companies upgrade their servers to newer processors is often because they want to reduce their power costs, and that a 2.6Ghz processor was still a 2.6Ghz processor, no matter when it was made. Benchmarks on various sites don't really support this theory, but I was wondering what server admin thought. Thanks for any advice.

  Read the article

• Windows 8 install app for multiple user accounts

  - by Robert Graves

  I purchased Adera episode 2 intending to play through it with my son. We each have our own user account on the same PC. When my son logged in, he was prompted to purchase the app which I had already purchased, installed, and played on the same PC. So I checked the Terms of Use. After selecting an app in the store, there is a Terms of Use link on the left side under the Install button. It is almost impossible to identify it as a link unless you put your mouse over it. The Terms of Use are standard across all apps in the store, not specific to particular apps. The terms of use indicates that the app may be installed on up to five devices, but says nothing about multiple user accounts on those devices. However, this Microsoft blog article indicates that it is allowed. Say, for example, that your family has a shared PC. You have previously used your Microsoft account to purchase a game that all your kids like to play. You can install it for each of your kids by having each of them sign in to their Windows accounts on the shared PC, then launch the Store and sign in to the Store using your own Microsoft account. There, you’ll see all your apps and you can re-install the app on your kid’s Windows account. Installing apps on multiple user accounts on a shared PC still only counts as one of the five allowable PCs where you can install apps. So I have two questions: Is it permissible under the Terms of Use to install the app under multiple accounts on the same device? If so, how do I do so given that my son has already signed into the store using his own Microsoft account.

  Read the article

• Remote reboot of windows to knoppix

  - by user64452

  I am attempting to develop an Auditing application. This audit application will be employed on windows networks. The Audit will need to discover Hardware and software details of all machines attached to the network (including Printers) I do not want to have to install this application on each workstation. The audit app. needs to discover all the ip addresses of all the networked workstations. I have been prototyping this app for the last couple of months and have decided to try a new tack Is this possible? a). You have a windows network, min Windows XP sp3 and upwards b). Maximum of 100 Networked machines (if that matters) c). I need to remotely reboot each WINDOWS machine in turn on the entire network and get it to startup using UNIX, say knoppix for example! d). however the knoppix live cd is only available from one of the networked machines Questions... Morphology? Longevity? Incept dates? Cheers DD

  Read the article

• iptables: How to combine DNAT and SNAT to use a secondary IP address?

  - by Que_273

  There are lots of questions on here about iptables DNAT/SNAT setups but I haven't found one that solves my current problem. I have services bound to the IP address of eth0 (e.g. 192.168.0.20) and I also have a IP address on eth0:0 (192.168.0.40) which is shared with another server. Only one server is active, so this alias interface comes and goes depending on which server is active. In order to get traffic accepted by the service a DNAT rule is used to change the destination IP. iptables -t nat -A PREROUTING -d 192.168.0.40 -p udp --dport 7100 -j DNAT --to-destination 192.168.0.20 I also wish all outbound traffic from this service to appear to come from the shared IP, so that return responses will work in the event of a active-standby failover. iptables -t nat -A POSTROUTING -p udp --sport 7100 -j SNAT --to-source 192.168.0.40 My problem is that the SNAT rule is not always run. Inbound traffic causes a connection tracking entry like this. [root]# conntrack -L -p udp udp 17 170 src=192.168.0.185 dst=192.168.0.40 sport=7100 dport=7100 src=192.168.0.20 dst=192.168.0.185 sport=7100 dport=7100 [ASSURED] mark=0 secmark=0 use=2 which means the POSTROUTING chain is not run and outbound traffic leaves with the real IP address as the source. I am thinking I can set up a NOTRACK rule in the raw table to prevent conntracking for this port number, but is there a better or more efficient way to make this work? Edit - Alternative question: Is there a way (in CentOS/Linux) to have an interface that can be bound to but not used, such that it can be attached to the network or detached when a shared IP address is swapped between servers?

  Read the article

• 403 Forbiden on Apache (CentOS) Server

  - by pouya

  These are my VM setup: HOST: windows 7 ultimate 32bit GUEST: CentOs 6.3 i386 Virtualization soft: Oracle virtualBox 4.1.22 Networking: NAT -> (PORT FORWARD: HOST:8080 => GUEST:80) Shared Folder: centos all the project files goes into shared folder and for each project file a virtualhost conf file is created in /etc/httpd/conf.d/ like /etc/httpd/conf.d/$domain I wasn't able to see anything in my browser before disabling both windows firewall and iptables in centos after that if i type for example: http://www.$domain:8080/ all i see is: Forbidden You don't have permission to access / on this server. Apache/2.2.15 (CentOS) Server at www.$domain.com Port 8080 A sample Virtual Host conf file: <VirtualHost *:80> #General DocumentRoot /media/sf_centos/path/to/public_html ServerAdmin webmaster@$domain ServerName www.$domain ServerAlias $domain *.$domain #Logging ErrorLog /var/log/httpd/$domain-error.log CustomLog /var/log/httpd/$domain-access.log combined #mod rewrite RewriteEngine On RewriteLog /var/log/httpd/$domain-rewrite.log RewriteLogLevel 0 </VirtualHost> centos shared folder is availabe to guest at /media/sf_centos These are file permissons for sf_centos: drwxrwx--- root vboxsf vboxsf group includes: apache and root So these are my questions: 1- How to solve Forbidden Problem? 2- How to setup both host and guest firewalls? 3- How can i improve this developement environment to simulate production environment as much as possible specially security improvements?

  Read the article

• As an admin, what tools do you use to log what you do to your boxes?

  - by Jerry

  I am more of a linux applications developer than an admin. Over time, I've built servers and maintained them, sometimes to offer services, mostly just to develop the applications I work on. Way back when I would create a file in my account to keep notes on what I did on each machine, so that I could replicate that when I migrated to other machines. Nowadays, I install something a private trac installation, install it's blog plugin, and then use that to make notes of everything I install, and most commands that I run, as well as the output. This provides me a combination wiki and blog that I find very useful as a "captain's log". I do this mostly so that when I migrate to a new clean machine, I have a much easier time in bringing it up. And yet, I am always amazed when I see others just install this, delete that, run this, setup this config, ... without seeming to use any way to actually note what they are doing. What do YOU do, and what tools are available? I am especially interested in the transition between maintaining a few machines for a few people and maintaining several to dozens of machines providing a real service. What are the best practices, and where can I find good resources? Thanks!

  Read the article

• One Way Sync with Dropbox?

  - by user244805

  Is there any way I can mirror a dropbox folder to my C drive by just running a portable file? Extra background information because I know you guys hate it when you don't get the entire situation: I go back to University in fall and I need a new storage solution. I decided to use DropBox to sync my tiny University files (< 5 MB). I need to access these files from 4 machines: Windows 7 Home machine Windows 7 University A machine Windows 7 University B machine Android tablet 1 and 4 are a non-issue. The problem lies with 2 and 3. I want to be able to edit my files on 2 and 3 but those machines are not mine. There is an easy fix. Run a portable version of the DropBox syncer on a USB drive. But the problem is that I don't want to carry a USB drive around with me all the time. In that case, I can just run the small portable DropBox syncer off the internet. But where will it to store the files? A temporary directory on the C drive. There is only one issue left: there are hundreds of machines that I will randomly use that fit in categories 2 and 3. My portable DropBox syncer will notice that the temporary directory is empty on each new PC I use and instead of downloading my DropBox folder to the machine, it syncs the other way around i.e. it deletes my entire DropBox. The solution is to mirror my DropBox onto the temporary directory before running the DropBox syncer.

  Read the article

• How do I connect remotely to SQL Server from Windows client?

  - by humble_coder

  Hi All, Having a bit of an issue connecting to SQL SERVER remotely from Windows. I've verified that all of my settings are correct via SQL SERVER MANAGEMENT STUDIO EXPRESS and SQL SERVER CONFIGURATION MANAGER. I can connect remotely using ODBC drivers from other OSes (e.g. OS X, Linux, etc). However, when I connect with the same credentials from a remote Windows machine using "SQL SERVER" as the driver I am told that the system cannot connect. I've tried creating an ODBC Data Source and I get the same error: Connection failed: SQLState: '01000' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]ConnectionOpen(InvalidInstance()). Connection failed: SQLState: '08001' SQL Server Error: 14 [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]Invalid Connection From the non-windows machines I can use the IP address of the SQL Server just fine. However, on the remote Windows machine, neither IP address nor named instance works. FYI, I can create an ODBC Data Source using the named instance on the machine actually running the SQL Server (but this is, of course, nothing special -- just proof that it isn't completely hosed). One interesting note: If I use SQL STUDIO 2005 from a Windows client machine, I can use the IP address to connect remotely. Still, the whole reason I bring this up is because I need to use a software package I've written to connect to SQL Server remotely from Windows machines as well. Previously the solution was only needed to xfer data from SQL Server into a PostGRES or MySQL database on non-Windows machines (due to DBA preference). However, now they also want to move the data from the legacy software to MySQL even on Windows. Any assistance would be most appreciated. Feel free to provide a full example connection string. Best

  Read the article

• Microsoft Server 2003 Explorer shows duplicate local shares

  - by user52167

  Hi folks, I am new here and I could really use some advice please. I am having a problem with our file server. When I try to browse the shared folders using explorer, several of the shared folders all appear to have the same name. Whenever I attempt to rename one of the affected folders, all the affected folders name also change. Our File Server is Windows Server 2003 R2. I am logged on directly to the server using remote desktop. When I open the folder all is as it should be, the proper content is there and the address bar displays the correct folder name and path. The share names are correct, so everything that needs to access the shared folder/files can do so. Also when I browse to the folder using the command-line all it as it should be there too. The only issue seems to be the incorrect display name when browsing using explorer. Can anyone offer any advice or help as to how to resolve this issue please? It would be most appreciated. Thanks

  Read the article

• How do I fully share a Hard Drive on my Local Network?

  - by GingerLee

  I have 4 computers connected to a router (DD-WRT) My main PC is Windows 7 (Home Premium). This machine has 2 Hard Disks: HD1 is used for my OS and the other (HD2) is used to store files. My 3 other machines are 1. Ubuntu Destop that I use to learn about linux, 2. A Mac OSX laptop, and 3. A netbook running windows 7. How do I easily share HD2 with my other machines? I would like all my machines to have full access & permissions to HD2 however I would like to RESTRICT access to only PCs that are connected to my router (either via LAN and WiFi) --- btw, I know this is not very secure due to WiFi vulnerability , however, I currently MAC address restrict WiFi connections my router. Extra Info: I have already tried to use the Windows Folder Sharing feature: i.e. I right click over the icon of HD2, and click on the Sharing Tab, but in sub-window labeled "Network File and Folder Sharing", the "Share" button is grayed out. I can click on "Advanced Shared" but that just takes me to a screen in which I have to set certain permissions. What is not clear to me is: How do I set a criteria that shares HD2 with all computer connected to my router?

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >