Search Results

Search found 590 results on 24 pages for 'aaron vegh'.

Page 11/24 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• VMware two vSwitches Guests can't communicate between them

  - by Aaron R.

  I have some servers in this configuration: And I am not able, from VMGuest1, to ping either VMGuest3 or VMGuest4. I can, however, ping Host1 and Host2, which are attached to pSwitch1. The behavior is the same with VMGuest3 or 4 trying to ping VMGuest 1 or 2. I don't have promiscuity enabled for any of these switches, nor do I have a bridge set up inside ESXi for the virtual switches. I know that one of these options is usually necessary when trying to get connectivity between two virtual switches. These switches are connected, however, through their respective physical switches which are bridged together. Ping just times out, arp request looks like this: [root@vmguest1:~]# arp -a vmguest3 vmguest3.example.com (1.2.3.4) at <incomplete> on eth0 [root@vmguest1:~]# arp -a host1 host1.example.com (1.2.3.5) at 00:0C:64:97:1C:FF [ether] on eth0 VMGuest1 can reach hosts on pSwitch1, so why can't it get to hosts on vSwitch1 through pSwitch1 the same way?

  Read the article

• Could hybrid SSD + HDD be made with fixed internal partitions?

  - by Aaron

  I was pretty close to getting Seagate's Momentus XT but have been scared off by the many problems reported on forums and feedback sites, especially in Mac Book Pros. So I'm waiting for mk 2 with some extra flash and better reliablilty I'm assuming will come out this year. What would suit me better though is a 32+500 hybrid drive where I have more control over what is on the flash drive and what is on the disk drive. So there are 2 physical partitions within the one 2.5" hard drive enclosure which use different media internally (32GB for core files and 500GB for data and multimedia). The partitions would be locked so they can't be changed. - Or even better, the disk driver just makes them appear as two disks to the OS that share the same bus... Perhaps it's ok if the bios just sees the first drive until the OS is loaded. Is either of it technically possible? Obviously difficult to market outside of the enthusiast market. The SSD memory modules can be pretty small right, so they could even make them a card that plugs into a secondary connection on the enclosure. That would be good for computer builders as well as for upgrading and recoverability. Then future operating systems could recognise these system SSD drives and automatically install the OS + swap files on it. While placing document libraries on the larger data drive. While in the longer term HDD will probably disapear there will always be a trade off between speed, storage size and expense.

  Read the article

• Compressing and copying large files on Windows Server?

  - by Aaron

  I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

  Read the article

• Compressed disk image on Linux

  - by Aaron Digulla

  I just got my new computer with a much bigger harddisk. I think I copied all important files over but just to be sure, I'd like to keep a disk image of my old disk. To save space, I'd like to compress it but I didn't find an option to mount a compressed image. My goals: Result must be easy to access No need to decompress the whole thing before I can access anything Files should be quick to locate - no TAR/CPIO archive Necessary space should be less than just copying the files over So ideally, I'm looking for a read-only, compressed file system which I can create in a file and which grows automatically.

  Read the article

• Red and blue are swapped on Youtube

  - by Aaron Digulla

  Since Sunday (April 1st), red and blue are sometimes swapped when I watch videos on YouTube. Examples are "Peeling Apple Like A Boss" (blue arms and apple) or, to my dismay, the famous Red vs. Blue series (like this video) which sucks. Here is a screenshot of the RvB episode at 1:28. Vimeo is OK, other web video services are OK, only most YouTube videos are affected ... well, all that I could find so far. This video looks OK in Firefox but it's broken in Chrome. The episode of RvB looks wrong in both browsers. Local videos look file. What could be causing this?

  Read the article

• In Stud, which Private RSA Key should be concatenated in the x509 SSL certificate pem file to avoid "self-signed" browser warning?

  - by Aaron

  I'm trying to implement Stud as an SSL termination point before HAProxy as a proof of concept for WebSockets routing. My domain registrar Gandi.net offers free 1-year SSL certs. Through OpenSSL, I generated a CSR which gave me two files: domain.key domain.csr I gave domain.csr to my trusted authority and they gave me two files: domain.cert GandiStandardSSLCA.pem (I think this is referred to as the intermediary cert?) This is where I encountered friction: Stud, which uses OpenSSL, expects there to be an "rsa private key" in the "pem-file" - which it describes as "SSL x509 certificate file. REQUIRED." If I add the domain.key to the bottom of Stud's pem-file, Stud will start but I receive the browser warning saying "The certificate is self-signed." If I omit the domain.key Stud will not start and throws an error triggered by an OpenSSL function that appears intended to determine whether or not my "pem-file" contains an "RSA Private Key". At this point I cannot determine whether the problem is: Free SSL cert will always be self-signed and will always cause browser to present warning I'm just not using Stud correctly I'm using the wrong "RSA private key" The CA domain cert, the intermediary cert, and the private key are in the wrong order.

  Read the article

• GVFS Locations Not Available In ~/.gvfs

  - by Aaron Copley

  So, I can mount GVFS locations correctly (specifically CIFS) either from the Gnome "Places" menu, or via the command line gvfs-mount, but the filesystem is not mounted in the expected location; ~/.gvfs. In fact, running the mount command does not list any GVFS filesystem at all. This is reproducible for non-root users while the root user behaves as expected. Strace reveals a permissions error for the user mounting the filesystem for the path /home/username/.gvfs. Ownership and permissions are correct and there are no extended attributes for the path as revealed by lsattr. Also, /root/.gvfs and /home/username/.gvfs are on the same filesystem. All packages are current. Any ideas?

  Read the article

• Skype 4.2 crashes when connecting to one specific person

  - by Aaron

  ok i have Skype 4.2 on Windows Vista 32 bit. Skype was working fine with no problems at all but a situation came up and i had to reformat my laptop. Since the reformat skype doesnt connect to just one person on my contacts list. Ive uninstalled reinstalled multiple times, even removed him from my contacts and readded but to no avail. He is on Skype mobile with his phone not sure if this is a prob as it wasnt before. any help or advice here would be much appreciated.

  Read the article

• How do I uninstall a ruby version installed via source?

  - by Aaron McIver

  I installed a version (1.9.3-p194) of ruby via source using make install and realized this may have been the wrong route to take. Upon doing this, I realized this was a mistake and I should be using a solution such as rvm to address my ruby versions within the OS. I looked to see if an uninstall existed to be ran in conjunction with make and it didn't. I then proceeded to install rvm and add the aforementioned version in to my list of managed rubies within rvm which is not listed as ext-ruby-1.9.3-p194. rvm rubies ext-ruby-1.9.3-p194 [ x86_64 ] =* ruby-1.9.3-p194 [ x86_64 ] # => - current # =* - current && default # * - default** When I perform an rvm remove, it simply removes it from the rubies list however it still exists within /usr/local/bin. I am not concerned with the system install ruby version residing in /usr/bin as I understand that is tied to the OS and should simply be ignored. How can I safely uninstall/remove the aforementioned version and all the places in which it was installed, short of looking at the install script?

  Read the article

• In 2011, what are the reasons to stick with plain text mails?

  - by Aaron Digulla

  People entering college today have never known a world without an Internet. HTML was invented 1980, that's more than thirty years ago or 1.5 generations. But plain text mails are still common despite all their problems: Encoding issues Wrapped code segments No links No way to use the "a picture says more than a thousand words" lore Most of the security risks are now handled by the underlying browser engine and smart settings like: Don't allow JavaScript in mails Don't execute attachments Don't download external resources (like web bugs) On top of that, only very few people still read mail only in command line tools like Mutt. Knowing Mutt myself, I'm pretty sure you can configure it to display HTML mail with, say, w3m. On top of that, most HTML mail capable clients send two versions of the mail (pure text with an HTML attachment). I'm not sure if there are any people left on the planet which still use a 56kbit modem to access their mail accounts. So what reasons are left to stick with plain text mails in 2011?

  Read the article

• Folder cannot be deleted

  - by Aaron

  I am using Windows XP Home Edition. When I try to delete a folder I have named cygwin. When I try to delete it or any file or folder within it, there is a long pause, and then an error pops up, saying: Cannot delete Cygwin: Access is denied. Make sure the disk is not full or read-write protected and that the file is not currently in use. I have tried deleting the folder and the files it contains with FileAssassin, and unlocking it with LockHunter. Neither report any errors unless I try to have them delete the file or folder, then I get an error message saying Access Denied. I have rebooted into Safe Mode to change the ownership, but I get Access Denied when I click OK or Apply. How can I delete this folder?

  Read the article

• Ruby installed on Ubuntu 10.10 slow on one machine but not other

  - by Aaron Jensen

  I have a machine that was provisioned several months ago. RVM was used to install ruby 1.9.3-p125 as well as 1.9.3-p125-perf. When I compared raw ruby performance to another identical machine the older machine smoked them. For example: ================================================================================ With in-block needle calculation ================================================================================ Rehearsal ---------------------------------------------- detect 3.790000 0.000000 3.790000 ( 3.800895) each 2.410000 0.000000 2.410000 ( 2.420860) any 3.960000 0.000000 3.960000 ( 3.972099) include 1.440000 0.000000 1.440000 ( 1.442862) ------------------------------------ total: 11.600000sec vs ================================================================================ With in-block needle calculation ================================================================================ Rehearsal ---------------------------------------------- detect 10.740000 0.000000 10.740000 ( 10.769366) each 6.080000 0.010000 6.090000 ( 6.106323) any 10.600000 0.000000 10.600000 ( 10.641606) include 4.160000 0.000000 4.160000 ( 4.171530) ------------------------------------ total: 31.590000sec I attempted to reinstall 1.9.3-p125 with rvm on the fast machine and that ruby is now slow. It's as if something changed in RVM, or I installed some package that made compiled versions of ruby perform significantly worse. I know this is a tough question to answer, but what things should I look into in order to track down why the performance has suffered so much? edit I just attempted to install with ruby-build and the version installed was fast. Something rvm is doing to build it in my environment is slow.

  Read the article

• Alt+click-drag window resizing on a Mac? (Similar to X-Windows)

  - by Aaron F.

  Is there a way I can get this behavior on Mac OS? alt + right-click-drag will resize the window, relative to where you've clicked within the window and the window's center alt + left-click-drag will move the window, regardless of where you've clicked within the window. There's a Windows port of this behavior as well: http://www.codeproject.com/KB/DLL/wm.aspx

  Read the article

• Retour de fonctions ou exceptions ? Une traduction de LittleWhite

  Bonjour à tous, Lorsqu'une erreur se produit dans une fonction, un développeur C++ a deux solutions : il peut soit retourner une valeur indiquant une erreur (par exemple avec return false; ou return ERROR_CODE;), soit lancer une exception. Mais quelle est la meilleure approche ? Dans cet article, Aaron Lahman apporte des éléments de réponse à cette question cruciale en regardant les différences en terme de lisibilité et d...

  Read the article

• Enterprise Redirection Services?

  - by Aaron Alton

  This is probably a case of "if I new what it was called, I could google it in 5 minutes" - but I don't know what it's called. It's probably best to explain the requirement using an example. We have a number of services (vpn, owa, etc) which we host from one of our datacenters. We have a number of datacenters, and we technically have the infrastructure already in place to support these services at a number of our datacenters. To provide access to these "services", I would create an external DNS entry (ex. VPN.MyCompany.com Gateway IP for one of my DCs), and clients will connect to it via the DNS entry. Since I have multiple datacenters that can support this service, I could theoretically offer a "highly available, geographically dispersed" solution if I could point this DNS entry to some sort of third party who offers highly available "redirection" services. If my primary site goes down, I could just make a change via some management console and configure the redirector to point to a different DC. Of course, it would be fairly straightforward to set this sort of thing up on one of our servers, but that would kinda defeat the purpose of a highly available third party. Is anyone familiar with a service like this? I'm thinking something like DynDNS, but with Enterprise availability guarantees.

  Read the article

• How to find the process(es) which are hogging the machine

  - by Aaron Digulla

  Scenario: All of a sudden, my computer feels sluggish. Mouse moves but windows take ages to open, etc. uptime says the load is 7.69 and raising. What is the fastest way to find out which process(es) are the cause of the load? Now, "top" and similar tools isn't the answer because they either show CPU or memory usage but not both at the same time. What I need is the single command which I might be able to type as it happens - something that will figure out any of System is trying to swap 8GB of RAM to disk because process X ... or process X seeks all over the disk or process X uses 400% CPU" So what I'm looking for is iostat, htop/atop and similar tools run into one with an output like this: 1235 cp - Disk trashing 87 chrome - Uses 2&nbsp;GB of RAM 137 nfs_bench - Uses 95% of the network bandwidth I don't want a tool that gives me some numbers which I can analyze but a tool that tells me exactly which process causes the current load. Assume that the user in front of the keyboard barely knows how to write "process", but the user is quickly overwhelmed when it comes to "resident size", "virtual memory" or "process life cycle". My argument goes like this: A user notices a problem. There can be thousands of reasons ... well, almost :-) The user wants to know the source of the problem. The current solutions give me lots of numbers, and I need to know what these numbers mean. What I'm looking for is a meta tool. 99% of the data is irrelevant to the problem. So what the tool should do is look for processes which hog some resource and list only those along with "this process needs a lot of CPU, this produces many IRQs, this process allocates a lot of RAM (and it's still growing)". This will be a relatively short list. It will be much more simple for someone new to this to locate the culprit from this list than from the output of, say, htop which gives me about 5000 numbers but requires me to fold multi-threaded processes myself (I have 50 lines which say VIRT 2750M but only 16 GB of RAM - the machine ought to swap itself to death but of course, this is a misinterpretation of the data that can happen quickly).

  Read the article

• SQL Server 2005 Replication Subscription Expiring Warning

  - by Aaron

  This week one of my replication subscriptions expired because I wasn't getting any alerts saying that there was a login error (I've fixed those alerts and the error). What I'd like now is, in the case that this happens again, to be able to send an alert saying that a subscription is about to expire (ie, it will expire in 1 or 2 days). I have an alert set up for when a subscription expires, but this is after the fact. I've looked through sys.messages for any text that has "Expir" in it, but I haven't found an appropriate error code yet. Would anyone be able to point me in the right direction? Thanks.

  Read the article

• Morris.JS X-Axis Label Height

  - by Aaron

  I have a chart generated with Morris.JS but the labels on the x-axis are to long and being cut off due to the limited height of the area showing the labels. The code below would render a graph that only shows the partial label for "COUNTY PARK ROAD ELEM.". How can I adjust the height of the label area to show the entire text? The code is as follow if ($('#IP1').length){ Morris.Bar({ element: 'IP1', data: [ {x: 'COUNTY PARK ROAD ELEM.', yIndex: 376.92} ], xkey: 'x', ykeys: ['yIndex'], labels: ['Index Points'], ymax: 500, barRatio: 0.2, xLabelAngle: 45, hideHover: 'auto' }); }

  Read the article

• Retrieve Radgrid DetailTable Items from Selected Item in JavaScript

  - by Aaron M

  I am trying to retrieve all of the children items in a detailtable of an item. I can get the item, but I am having no luck in trying to get the children items. Here is the relevant code that I have so far var MasterTable = radgrid.get_masterTableView(); var selectedRows = MasterTable.get_selectedItems(); for (i = 0; i < selectedRows.length; i++) { var row = selectedRows[i]; }

  Read the article

• upload streaming to WCF IIS 7 hosted service not working

  - by Aaron Fischer

  I have a wcf service I am setting up to run under IIS 7. I have the service set to streaming for the transfermode but when my service is hosted on IIS I get a time out for the client service call. If I self host the service in a console application I don't have a problem and the service streams just fine.

  Read the article

• C# WebBrowser Control System.AccessViolationException

  - by Aaron Smith

  I have a program that uses the built in webbrowser control. At some point during the usage of this, I'm not sure at what point, but it appears to be random, I get the following error: System.AccessViolationException FullText = System.AccessViolationException: Attempted to read or write protected memory. This is often an indication that other memory is corrupt. at System.Windows.Forms.UnsafeNativeMethods.DispatchMessageW(MSG& msg) at System.Windows.Forms.Application.ComponentManager.System.Windows.Forms.UnsafeNativeMethods.IMsoComponentManager.FPushMessageLoop(Int32 dwComponentID, Int32 reason, Int32 pvLoopData) at System.Windows.Forms.Application.ThreadContext.RunMessageLoopInner(Int32 reason, ApplicationContext context) at System.Windows.Forms.Application.ThreadContext.RunMessageLoop(Int32 reason, ApplicationContext context) at System.Windows.Forms.Application.Run(Form mainForm) Does anyone have any clues as to why I would get this and how to prevent it?

  Read the article

• Sending Client Certificate in HttpWebRequest

  - by Aaron Fischer

  I am trying to pass a client certificate to a server using the code below however I still revive the HTTP Error 403.7 - Forbidden: SSL client certificate is required. What are the possible reasons the HttpWebRequest would not send the client certificate? var clientCertificate = new X509Certificate2( @"C:\Development\TestClient.pfx", "bob" ); HttpWebRequest tRequest = ( HttpWebRequest )WebRequest.Create( "https://ofxtest.com/ofxr.dll" ); tRequest.ClientCertificates.Add( clientCertificate ); tRequest.PreAuthenticate = true; tRequest.KeepAlive = true; tRequest.Credentials = CredentialCache.DefaultCredentials; tRequest.Method = "POST"; var encoder = new ASCIIEncoding(); var requestData = encoder.GetBytes( "<OFX></OFX>" ); tRequest.GetRequestStream().Write( requestData, 0, requestData.Length ); tRequest.GetRequestStream().Close(); ServicePointManager.ServerCertificateValidationCallback = new System.Net.Security.RemoteCertificateValidationCallback( CertPolicy.ValidateServerCertificate ); WriteResponse( tRequest.GetResponse() );

  Read the article

• C Sharp -- PInvokeStackImbalance detected on a well documented function?

  - by Aaron Hammond

  Here is my code for a ClickMouse() function: [DllImport("user32.dll", CharSet = CharSet.Auto, CallingConvention = CallingConvention.StdCall)] public static extern void mouse_event(long dwFlags, long dx, long dy, long cButtons, long dwExtraInfo); private const long MOUSEEVENTF_LEFTDOWN = 0x02; private const long MOUSEEVENTF_LEFTUP = 0x04; private const long MOUSEEVENTF_RIGHTDOWN = 0x08; private const long MOUSEEVENTF_RIGHTUP = 0x10; private void ClickMouse() { long X = Cursor.Position.X; long Y = Cursor.Position.Y; mouse_event(MOUSEEVENTF_LEFTDOWN | MOUSEEVENTF_LEFTUP, X, Y, 0, 0); } For some reason, when my program comes to this code, it throws this error message: PInvokeStackImbalance was detected Message: A call to PInvoke function 'WindowsFormsApplication1!WindowsFormsApplication1.Form1::mouse_event' has unbalanced the stack. This is likely because the managed PInvoke signature does not match the unmanaged target signature. Check that the calling convention and parameters of the PInvoke signature match the target unmanaged signature. Please help?

  Read the article

• Intermittent PolicyException: Execution permission cannot be acquired.

  - by Aaron Maenpaa

  We are intermittently seeing the following exception shortly after an App Pool recycle in an ASP.NET application: System.Configuration.ConfigurationErrorsException: Could not load file or assembly 'Microsoft.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' or one of its dependencies. Failed to grant permission to execute. (Exception from HRESULT: 0x80131418) ---> System.IO.FileLoadException: Could not load file or assembly 'Microsoft.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' or one of its dependencies. Failed to grant permission to execute. (Exception from HRESULT: 0x80131418) File name: 'Microsoft.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=null' ---> System.Security.Policy.PolicyException: Execution permission cannot be acquired. at System.Security.SecurityManager.ResolvePolicy(Evidence evidence, PermissionSet reqdPset, PermissionSet optPset, PermissionSet denyPset, PermissionSet& denied, Boolean checkExecutionPermission) at System.Security.SecurityManager.ResolvePolicy(Evidence evidence, PermissionSet reqdPset, PermissionSet optPset, PermissionSet denyPset, PermissionSet& denied, Int32& securitySpecialFlags, Boolean checkExecutionPermission) at System.Reflection.Assembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, Assembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection) at System.Reflection.Assembly.InternalLoad(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) at System.Reflection.Assembly.InternalLoad(String assemblyString, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) at System.Reflection.Assembly.Load(String assemblyString) at System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) The specific DLL that fails to load varies from incident to incident, but is always one referenced by the main assembly. We're running on ASP.NET 3.5 on Windows Server 2008. This seems to happen in batches affecting some but not all of sites on the same App Pool. We have a large number of sites all running the same code. Once a site has failed to load a DLL it throws up a Yellow Screen of Death until the next App Pool recycle. We haven't been able to reproduce this behavior and the sites seem to work fine for days or weeks at a time (and many App Pool recycles) before failing. Has anybody else seen similar behavior? Update: We've tried reproducing the failure by setting up a few hundred sites and writing a script to hit them repeatedly while recycling the App Pool once every couple of minutes and were unable to accomplish much other than loading down the server's CPU for a few days straight. We then tried messing (locking one of the DLLs, changing the file permissions) with the copies of the DLLs that ASP.NET makes and managed to reproduce similar behavior but not the same exception. Does anybody have any ideas on how to adjust the security policy to get it to throw a System.Security.Policy.PolicyException: Execution permission cannot be acquired. when loading a specific DLL?

  Read the article

• Resizing QT's QTextEdit to Match Text Height: maximumViewportSize()

  - by Aaron

  I am trying to use a QTextEdit widget inside of a form containing several QT widgets. The form itself sits inside a QScrollArea that is the central widget for a window. My intent is that any necessary scrolling will take place in the main QScrollArea (rather than inside any widgets), and any widgets inside will automatically resize their height to hold their contents. I have tried to implement the automatic resizing of height with a QTextEdit, but have run into an odd issue. I created a sub-class of QTextEdit and reimplemented sizeHint() like this: QSize OperationEditor::sizeHint() const { QSize sizehint = QTextBrowser::sizeHint(); sizehint.setHeight(this->fitted_height); return sizehint; } this-fitted_height is kept up-to-date via this slot that is wired to the QTextEdit's "contentsChanged()" signal: void OperationEditor::fitHeightToDocument() { this->document()->setTextWidth(this->viewport()->width()); QSize document_size(this->document()->size().toSize()); this->fitted_height = document_size.height(); this->updateGeometry(); } The size policy of the QTextEdit sub-class is: this->setSizePolicy(QSizePolicy::MinimumExpanding, QSizePolicy::Preferred); I took this approach after reading this post. Here is my problem: As the QTextEdit gradually resizes to fill the window, it stops getting larger and starts scrolling within the QTextEdit, no matter what height is returned from sizeHint(). If I initially have sizeHint() return some large constant number, then the QTextEdit is very big and is contained nicely within the outer QScrollArea, as one would expect. However, if sizeHint gradually adjusts the size of the QTextEdit rather than just making it really big to start, then it tops out when it fills the current window and starts scrolling instead of growing. I have traced this problem to be that, no matter what my sizeHint() returns, it will never resize the QTextEdit larger than the value returned from maximumViewportSize(), which is inherited from QAbstractScrollArea. Note that this is not the same number as viewport()-maximumSize(). I am unable to figure out how to set that value. Looking at QT's source code, maximumViewportSize() is returning "the size of the viewport as if the scroll bars had no valid scrolling range." This value is basically computed as the current size of the widget minus (2 * frameWidth + margins) plus any scrollbar widths/heights. This does not make a lot of sense to me, and it's not clear to me why that number would be used anywhere in a way that supercede's the sub-class's sizeHint() implementation. Also, it does seem odd that the single "frameWidth" integer is used in computing both the width and the height. Can anyone please shed some light on this? I suspect that my poor understanding of QT's layout engine is to blame here.

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >