Search Results

Search found 258 results on 11 pages for 'archie ec'.

Page 11/11 | < Previous Page | 7 8 9 10 11 

• MacBook Pro Late 2009 SATA Resets, Slowness

  - by A Student at a University

  My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. The resets correlate with AC power connects and disconnects. I don't know if the warnings do. (How do I tell?) Are these bus CRC errors? Or something else? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16 :[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16 :[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16 :[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16 :[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16 :[ 0.813473] scsi0 : ahci 02:37:16 :[ 0.823340] scsi1 : ahci 02:37:16 :[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16 :[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16 :[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16 :[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16 :[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.229570] ata2.00: configured for UDMA/133 02:37:16 :[ 1.240133] ata2: hard resetting link 02:37:16 :[ 1.260738] ata1.00: configured for UDMA/133 02:37:16 :[ 1.280122] ata1: hard resetting link 02:37:16 :[ 1.470125] usb 2-5: new high speed USB device using ehci_hcd and address 3 02:37:16 :[ 1.550165] firewire_core: created device fw0: GUID 58b035fffea99f5c, S800 02:37:16 :[ 1.631306] Initializing USB Mass Storage driver... 02:37:16 :[ 1.631392] scsi6 : usb-storage 2-5:1.0 02:37:16 :[ 1.631454] usbcore: registered new interface driver usb-storage 02:37:16 :[ 1.631455] USB Mass Storage support registered. 02:37:16 :[ 1.960128] usb 4-1: new full speed USB device using ohci_hcd and address 2 02:37:16 :[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.994215] ata2.00: configured for UDMA/133 02:37:16 :[ 1.994220] ata2: EH complete 02:37:16 :[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 2.090773] ata1.00: configured for UDMA/133 02:37:16 :[ 2.090778] ata1: EH complete 02:37:16 :[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16 :[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16 :[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16 :[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16 :[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16 :[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16 :[ 2.091337] sda: 02:37:16 :[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16 :[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16 :[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091756] sdb: sda1 sda2 02:37:16 :[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16 :[ 2.093505] sdb1 sdb2 sdb3 02:37:16 :[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16 :[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16 :[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16 :[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25 :[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25 :[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25 :[ 19.641533] ata1: hard resetting link 02:37:25 :[ 19.642084] ata2: hard resetting link 02:37:26 :[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.396697] ata2.00: configured for UDMA/133 02:37:26 :[ 20.396703] ata2: EH complete 02:37:26 :[ 20.451491] ata1.00: configured for UDMA/133 02:37:26 :[ 20.451498] ata1: EH complete 02:37:30 :[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30 :[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30 :[ 24.627246] ata1: hard resetting link 02:37:30 :[ 24.632250] ata2: hard resetting link 02:37:31 :[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.386782] ata2.00: configured for UDMA/133 02:37:31 :[ 25.386788] ata2: EH complete 02:37:31 :[ 25.431668] ata1.00: configured for UDMA/133 02:37:31 :[ 25.431674] ata1: EH complete 02:45:54 :[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55 :[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55 :[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622583] ata1: hard resetting link 02:45:55 :[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622624] ata2: hard resetting link 02:45:56 :[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.384305] ata2.00: configured for UDMA/133 02:45:56 :[ 530.384314] ata2: EH complete 02:45:56 :[ 530.399225] ata1.00: configured for UDMA/133 02:45:56 :[ 530.399233] ata1: EH complete 02:45:58 :[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58 :[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58 :[ 532.590983] ata1: hard resetting link 02:45:58 :[ 532.591045] ata2: hard resetting link 02:45:59 :[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.344416] ata2.00: configured for UDMA/133 02:45:59 :[ 533.344424] ata2: EH complete 02:45:59 :[ 533.360839] ata1.00: configured for UDMA/133 02:45:59 :[ 533.360847] ata1: EH complete 02:45:59 :[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59 :[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59 :[ 533.660132] ata2: hard resetting link 02:45:59 :[ 533.660151] ata1: hard resetting link 02:46:00 :[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.416768] ata2.00: configured for UDMA/133 02:46:00 :[ 534.416777] ata2: EH complete 02:46:00 :[ 534.431396] ata1.00: configured for UDMA/133 02:46:00 :[ 534.431401] ata1: EH complete 02:46:03 :[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03 :[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03 :[ 537.586002] ata1: hard resetting link 02:46:03 :[ 537.586036] ata2: hard resetting link 02:46:04 :[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.334389] ata2.00: configured for UDMA/133 02:46:04 :[ 538.334398] ata2: EH complete 02:46:04 :[ 538.343511] ata1.00: configured for UDMA/133 02:46:04 :[ 538.343519] ata1: EH complete 02:46:04 :[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04 :[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04 :[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540159] ata1: hard resetting link 02:46:04 :[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540220] ata2: hard resetting link 02:46:05 :[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.294100] ata2.00: configured for UDMA/100 02:46:05 :[ 539.294106] ata2: EH complete 02:46:05 :[ 539.314125] ata1.00: configured for UDMA/100 02:46:05 :[ 539.314132] ------------[ cut here ]------------ 02:46:05 :[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05 :[ 539.314144] Hardware name: MacBookPro5,3 02:46:05 :[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05 :[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05 :[ 539.314224] Call Trace: 02:46:05 :[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05 :[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05 :[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05 :[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05 :[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05 :[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05 :[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05 :[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05 :[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05 :[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05 :[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05 :[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05 :[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05 :[ 539.314296] ata1: EH complete 02:46:12 :[ 547.040117] ata1: hard resetting link 02:46:13 :[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13 :[ 547.408430] ata1.00: configured for UDMA/100 02:46:13 :[ 547.408438] ------------[ cut here ]------------ 02:46:13 :[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13 :[ 547.408451] Hardware name: MacBookPro5,3 02:46:13 :[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13 :[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13 :[ 547.408531] Call Trace: 02:46:13 :[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13 :[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13 :[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13 :[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13 :[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13 :[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13 :[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13 :[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13 :[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13 :[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13 :[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13 :[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13 :[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13 :[ 547.408620] ata1: EH complete 02:46:13 :[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13 :[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13 :[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13 :[ 547.738218] ata1: hard resetting link 02:46:13 :[ 547.738274] ata2: hard resetting link 02:46:14 :[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.486809] ata2.00: configured for UDMA/100 02:46:14 :[ 548.486818] ata2: EH complete 02:46:14 :[ 548.498998] ata1.00: configured for UDMA/33 02:46:14 :[ 548.499004] ata1: EH complete 02:46:18 :[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18 :[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18 :[ 552.529684] ata1: hard resetting link 02:46:18 :[ 552.529723] ata2: hard resetting link 02:46:19 :[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.284141] ata2.00: configured for UDMA/100 02:46:19 :[ 553.284150] ata2: EH complete 02:46:19 :[ 553.301629] ata1.00: configured for UDMA/33 02:46:19 :[ 553.301637] ata1: EH complete 02:46:21 :[ 556.078830] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:21 :[ 556.180361] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:22 :[ 556.262612] ata1: hard resetting link 02:46:22 :[ 556.262617] ata2: hard resetting link 02:46:22 :[ 557.010050] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.010070] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.014069] ata2.00: configured for UDMA/100 02:46:22 :[ 557.014075] ata2: EH complete 02:46:22 :[ 557.023646] ata1.00: configured for UDMA/33 02:46:22 :[ 557.023654] ata1: EH complete 02:46:30 :[ 565.047438] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:30 :[ 565.051554] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:30 :[ 565.108332] ata1: hard resetting link 02:46:30 :[ 565.108389] ata2.00: limiting speed to UDMA/33:PIO4 02:46:30 :[ 565.108406] ata2: hard resetting link 02:46:31 :[ 565.850048] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.850068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.854304] ata2.00: configured for UDMA/33 02:46:31 :[ 565.854313] ata2: EH complete 02:46:31 :[ 565.868477] ata1.00: configured for UDMA/33 02:46:31 :[ 565.868485] ata1: EH complete 02:46:35 :[ 569.265469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:35 :[ 569.268139] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:35 :[ 569.340079] ata1: hard resetting link 02:46:35 :[ 569.340113] ata2: hard resetting link 02:46:35 :[ 570.092568] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.092589] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.096828] ata2.00: configured for UDMA/33 02:46:35 :[ 570.096837] ata2: EH complete 02:46:35 :[ 570.110727] ata1.00: configured for UDMA/33 02:46:35 :[ 570.110735] ata1: EH complete 02:47:04 :[ 598.528232] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:47:04 :[ 598.653973] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:47:04 :[ 598.730854] ata1: hard resetting link 02:47:04 :[ 598.730910] ata2: hard resetting link 02:47:05 :[ 599.480136] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.480159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.484206] ata2.00: configured for UDMA/33 02:47:05 :[ 599.484213] ata2: EH complete 02:47:05 :[ 599.496699] ata1.00: configured for UDMA/33 02:47:05 :[ 599.496707] ata1: EH complete 04:45:59 :[ 7733.756548] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 04:45:59 :[ 7733.882748] EXT4-fs (dm-2): re-mounted. Opts: commit=0 04:45:59 :[ 7733.960142] ata1: hard resetting link 04:45:59 :[ 7733.960189] ata2: hard resetting link 04:46:00 :[ 7734.701926] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.719939] ata1.00: configured for UDMA/33 04:46:00 :[ 7734.719946] ata1: EH complete 04:46:00 :[ 7734.722547] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.726652] ata2.00: configured for UDMA/33 04:46:00 :[ 7734.726659] ata2: EH complete 04:46:02 :[ 7736.656465] ACPI: EC: GPE storm detected, transactions will use polling mode 13:38:49 :[39704.188621] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 13:38:49 :[39704.280588] EXT4-fs (dm-2): re-mounted. Opts: commit=600 13:38:49 :[39704.360819] ata1: hard resetting link 13:38:49 :[39704.360882] ata2: hard resetting link 13:38:50 :[39705.112956] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.114435] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.118673] ata2.00: configured for UDMA/33 13:38:50 :[39705.118682] ata2: EH complete 13:38:50 :[39705.127076] ata1.00: configured for UDMA/33 13:38:50 :[39705.127084] ata1: EH complete 13:39:49 :[39764.142463] applesmc: F1Mn: write arg fail 13:48:11 :[40267.025145] applesmc: FS! : read arg fail 13:52:53 :[40548.596735] applesmc: FS! : read arg fail 13:53:58 :[40613.972856] applesmc: FS! : read arg fail 13:54:08 :[40624.057339] applesmc: FS! : read arg fail 13:58:20 :[40875.397749] applesmc: TC0D: read data fail 14:16:56 :[41991.722054] applesmc: Th2H: read data fail 14:22:32 :[42327.991522] applesmc: light sensor data length set to 10 14:26:19 :[42554.788886] applesmc: F1Mn: write arg fail 14:32:36 :[42931.860443] applesmc: TC0F: read data fail 14:34:32 :[43048.041469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 14:34:33 :[43048.185850] EXT4-fs (dm-2): re-mounted. Opts: commit=0 14:34:33 :[43048.270184] ata1: hard resetting link 14:34:33 :[43048.270224] ata2: hard resetting link 14:34:33 :[43049.030049] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.030065] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.034106] ata2.00: configured for UDMA/33 14:34:33 :[43049.034112] ata2: EH complete 14:34:33 :[43049.056952] ata1.00: configured for UDMA/33 14:34:33 :[43049.056959] ------------[ cut here ]------------ 14:34:33 :[43049.056968] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:33 :[43049.056971] Hardware name: MacBookPro5,3 14:34:33 :[43049.056973] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:33 :[43049.057048] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:33 :[43049.057052] Call Trace: 14:34:33 :[43049.057060] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:33 :[43049.057064] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:33 :[43049.057069] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:33 :[43049.057074] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:33 :[43049.057083] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:33 :[43049.057088] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:33 :[43049.057093] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:33 :[43049.057097] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:33 :[43049.057102] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:33 :[43049.057107] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:33 :[43049.057111] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:33 :[43049.057115] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:33 :[43049.057118] ---[ end trace 76dbffc2d5d49d9d ]--- 14:34:33 :[43049.057123] ata1: EH complete 14:34:41 :[43057.012698] ata1: hard resetting link 14:34:42 :[43057.362780] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:42 :[43057.381432] ata1.00: configured for UDMA/33 14:34:42 :[43057.381441] ------------[ cut here ]------------ 14:34:42 :[43057.381450] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:42 :[43057.381453] Hardware name: MacBookPro5,3 14:34:42 :[43057.381455] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:42 :[43057.381530] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:42 :[43057.381533] Call Trace: 14:34:42 :[43057.381542] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:42 :[43057.381546] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:42 :[43057.381551] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:42 :[43057.381556] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:42 :[43057.381565] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:42 :[43057.381569] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:42 :[43057.381575] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:42 :[43057.381579] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:42 :[43057.381584] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:42 :[43057.381589] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:42 :[43057.381594] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:42 :[43057.381598] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:42 :[43057.381601] ---[ end trace 76dbffc2d5d49d9e ]--- 14:34:42 :[43057.381624] ata1: EH complete 14:34:42 :[43057.557887] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:42 :[43057.560517] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:42 :[43057.621194] ata1: hard resetting link 14:34:42 :[43057.621252] ata2: hard resetting link 14:34:43 :[43058.370141] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.370162] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.374407] ata2.00: configured for UDMA/33 14:34:43 :[43058.374415] ata2: EH complete 14:34:43 :[43058.381989] ata1.00: configured for UDMA/33 14:34:43 :[43058.381996] ata1: EH complete 14:34:43 :[43058.616228] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:43 :[43058.618931] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:43 :[43058.626687] ata1: hard resetting link 14:34:43 :[43058.626731] ata2: hard resetting link 14:34:44 :[43059.372908] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.372932] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.376997] ata2.00: configured for UDMA/33 14:34:44 :[43059.377003] ata2: EH complete 14:34:44 :[43059.392576] ata1.00: configured for UDMA/33 14:34:44 :[43059.392585] ata1: EH complete 15:48:19 :[47474.710860] ata1: hard resetting link 15:48:19 :[47474.710882] ata2: hard resetting link 15:48:20 :[47475.460144] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.460169] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.473709] ata1.00: configured for UDMA/33 15:48:20 :[47475.473717] ata1: EH complete 15:48:20 :[47475.727960] ata2.00: configured for UDMA/33 15:48:20 :[47475.727969] ata2: EH complete 16:29:39 :[49954.295017] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 16:29:39 :[49954.622307] EXT4-fs (dm-2): re-mounted. Opts: commit=0 16:29:39 :[49954.710139] ata1: hard resetting link 16:29:39 :[49954.710174] ata2: hard resetting link 16:29:40 :[49955.460046] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.460062] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.464138] ata2.00: configured for UDMA/33 16:29:40 :[49955.464144] ata2: EH complete 16:29:40 :[49955.473251] ata1.00: configured for UDMA/33 16:29:40 :[49955.473258] ata1: EH complete

  Read the article

• Internet doesn't work by default

  - by Adam Martinez

  After upgrading to Precise, I am required to run 'sudo dhclient eth0' in a terminal in order to get the internet to work. Everything worked perfectly fine on Oneiric, so It's really puzzling me. I'm thinking it could possibly be something with the kernel, but who knows. Output of dmesg: [ 0.247891] system 00:01: [io 0x0290-0x030f] has been reserved [ 0.247896] system 00:01: [io 0x0290-0x0297] has been reserved [ 0.247901] system 00:01: [io 0x0880-0x088f] has been reserved [ 0.247908] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.247931] pnp 00:02: [dma 4] [ 0.247935] pnp 00:02: [io 0x0000-0x000f] [ 0.247939] pnp 00:02: [io 0x0080-0x0090] [ 0.247943] pnp 00:02: [io 0x0094-0x009f] [ 0.247947] pnp 00:02: [io 0x00c0-0x00df] [ 0.248033] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.248125] pnp 00:03: [io 0x0070-0x0073] [ 0.248187] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.248205] pnp 00:04: [io 0x0061] [ 0.248260] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.248277] pnp 00:05: [io 0x00f0-0x00ff] [ 0.248292] pnp 00:05: [irq 13] [ 0.248348] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.248583] pnp 00:06: [io 0x03f0-0x03f5] [ 0.248588] pnp 00:06: [io 0x03f7] [ 0.248597] pnp 00:06: [irq 6] [ 0.248601] pnp 00:06: [dma 2] [ 0.248690] pnp 00:06: Plug and Play ACPI device, IDs PNP0700 (active) [ 0.248998] pnp 00:07: [io 0x03f8-0x03ff] [ 0.249008] pnp 00:07: [irq 4] [ 0.249122] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.249479] pnp 00:08: [io 0x0400-0x04bf] [ 0.249584] system 00:08: [io 0x0400-0x04bf] has been reserved [ 0.249591] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.249628] pnp 00:09: [mem 0xffb80000-0xffbfffff] [ 0.249690] pnp 00:09: Plug and Play ACPI device, IDs INT0800 (active) [ 0.250049] pnp 00:0a: [mem 0xe0000000-0xefffffff] [ 0.250167] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved [ 0.250173] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.250302] pnp 00:0b: [mem 0x000f0000-0x000fffff] [ 0.250307] pnp 00:0b: [mem 0x7ff00000-0x7fffffff] [ 0.250311] pnp 00:0b: [mem 0xfed00000-0xfed000ff] [ 0.250316] pnp 00:0b: [mem 0x0000046e-0x0000056d] [ 0.250320] pnp 00:0b: [mem 0x7fee0000-0x7fefffff] [ 0.250324] pnp 00:0b: [mem 0x00000000-0x0009ffff] [ 0.250328] pnp 00:0b: [mem 0x00100000-0x7fedffff] [ 0.250332] pnp 00:0b: [mem 0xfec00000-0xfec00fff] [ 0.250336] pnp 00:0b: [mem 0xfed14000-0xfed1dfff] [ 0.250341] pnp 00:0b: [mem 0xfed20000-0xfed9ffff] [ 0.250345] pnp 00:0b: [mem 0xfee00000-0xfee00fff] [ 0.250349] pnp 00:0b: [mem 0xffb00000-0xffb7ffff] [ 0.250353] pnp 00:0b: [mem 0xfff00000-0xffffffff] [ 0.250357] pnp 00:0b: [mem 0x000e0000-0x000effff] [ 0.250409] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0007ffff pref] [ 0.250419] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref] [ 0.250430] pnp 00:0b: disabling [mem 0x0000046e-0x0000056d disabled] because it overlaps 0000:04:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref] [ 0.250524] system 00:0b: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.250530] system 00:0b: [mem 0x7ff00000-0x7fffffff] has been reserved [ 0.250536] system 00:0b: [mem 0xfed00000-0xfed000ff] has been reserved [ 0.250541] system 00:0b: [mem 0x7fee0000-0x7fefffff] could not be reserved [ 0.250547] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved [ 0.250552] system 00:0b: [mem 0x00100000-0x7fedffff] could not be reserved [ 0.250558] system 00:0b: [mem 0xfec00000-0xfec00fff] could not be reserved [ 0.250563] system 00:0b: [mem 0xfed14000-0xfed1dfff] has been reserved [ 0.250568] system 00:0b: [mem 0xfed20000-0xfed9ffff] has been reserved [ 0.250574] system 00:0b: [mem 0xfee00000-0xfee00fff] has been reserved [ 0.250579] system 00:0b: [mem 0xffb00000-0xffb7ffff] has been reserved [ 0.250585] system 00:0b: [mem 0xfff00000-0xffffffff] has been reserved [ 0.250590] system 00:0b: [mem 0x000e0000-0x000effff] has been reserved [ 0.250596] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.250614] pnp: PnP ACPI: found 12 devices [ 0.250617] ACPI: ACPI bus type pnp unregistered [ 0.250624] PnPBIOS: Disabled by ACPI PNP [ 0.288725] PCI: max bus depth: 1 pci_try_num: 2 [ 0.288786] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb07ffff pref] [ 0.288792] pci 0000:00:01.0: PCI bridge to [bus 01-01] [ 0.288797] pci 0000:00:01.0: bridge window [io 0xa000-0xafff] [ 0.288804] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xfbffffff] [ 0.288811] pci 0000:00:01.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.288820] pci 0000:00:1c.0: PCI bridge to [bus 02-02] [ 0.288825] pci 0000:00:1c.0: bridge window [io 0x9000-0x9fff] [ 0.288833] pci 0000:00:1c.0: bridge window [mem 0xfdb00000-0xfdbfffff] [ 0.288840] pci 0000:00:1c.0: bridge window [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.288851] pci 0000:03:00.0: BAR 6: assigned [mem 0xfde00000-0xfde0ffff pref] [ 0.288856] pci 0000:00:1c.4: PCI bridge to [bus 03-03] [ 0.288861] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff] [ 0.288869] pci 0000:00:1c.4: bridge window [mem 0xfd700000-0xfd7fffff] [ 0.288876] pci 0000:00:1c.4: bridge window [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.288887] pci 0000:04:00.0: BAR 6: assigned [mem 0xfdc00000-0xfdc1ffff pref] [ 0.288891] pci 0000:00:1c.5: PCI bridge to [bus 04-04] [ 0.288897] pci 0000:00:1c.5: bridge window [io 0xb000-0xbfff] [ 0.288904] pci 0000:00:1c.5: bridge window [mem 0xfdd00000-0xfddfffff] [ 0.288911] pci 0000:00:1c.5: bridge window [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.288920] pci 0000:00:1e.0: PCI bridge to [bus 05-05] [ 0.288926] pci 0000:00:1e.0: bridge window [io 0xc000-0xcfff] [ 0.288933] pci 0000:00:1e.0: bridge window [mem 0xfda00000-0xfdafffff] [ 0.288940] pci 0000:00:1e.0: bridge window [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.288971] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288979] pci 0000:00:01.0: setting latency timer to 64 [ 0.288991] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.288998] pci 0000:00:1c.0: setting latency timer to 64 [ 0.289008] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.289014] pci 0000:00:1c.4: setting latency timer to 64 [ 0.289030] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.289037] pci 0000:00:1c.5: setting latency timer to 64 [ 0.289047] pci 0000:00:1e.0: setting latency timer to 64 [ 0.289054] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.289058] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.289063] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289067] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289072] pci_bus 0000:00: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289077] pci_bus 0000:01: resource 0 [io 0xa000-0xafff] [ 0.289081] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff] [ 0.289086] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref] [ 0.289092] pci_bus 0000:02: resource 0 [io 0x9000-0x9fff] [ 0.289096] pci_bus 0000:02: resource 1 [mem 0xfdb00000-0xfdbfffff] [ 0.289101] pci_bus 0000:02: resource 2 [mem 0xfd800000-0xfd8fffff 64bit pref] [ 0.289106] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.289110] pci_bus 0000:03: resource 1 [mem 0xfd700000-0xfd7fffff] [ 0.289115] pci_bus 0000:03: resource 2 [mem 0xfde00000-0xfdefffff 64bit pref] [ 0.289120] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff] [ 0.289124] pci_bus 0000:04: resource 1 [mem 0xfdd00000-0xfddfffff] [ 0.289129] pci_bus 0000:04: resource 2 [mem 0xfdc00000-0xfdcfffff 64bit pref] [ 0.289134] pci_bus 0000:05: resource 0 [io 0xc000-0xcfff] [ 0.289138] pci_bus 0000:05: resource 1 [mem 0xfda00000-0xfdafffff] [ 0.289143] pci_bus 0000:05: resource 2 [mem 0xfd900000-0xfd9fffff 64bit pref] [ 0.289148] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7] [ 0.289152] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff] [ 0.289157] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff] [ 0.289161] pci_bus 0000:05: resource 7 [mem 0x000c0000-0x000dffff] [ 0.289166] pci_bus 0000:05: resource 8 [mem 0x7ff00000-0xfebfffff] [ 0.289233] NET: Registered protocol family 2 [ 0.289360] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.289754] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.290351] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.290670] TCP: Hash tables configured (established 131072 bind 65536) [ 0.290674] TCP reno registered [ 0.290680] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.290703] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.290868] NET: Registered protocol family 1 [ 0.290911] pci 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.290932] pci 0000:00:1a.0: PCI INT A disabled [ 0.290956] pci 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.290975] pci 0000:00:1a.1: PCI INT B disabled [ 0.290992] pci 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.291012] pci 0000:00:1a.2: PCI INT D disabled [ 0.291031] pci 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291068] pci 0000:00:1a.7: PCI INT C disabled [ 0.291104] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291123] pci 0000:00:1d.0: PCI INT A disabled [ 0.291135] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.291155] pci 0000:00:1d.1: PCI INT B disabled [ 0.291166] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.291185] pci 0000:00:1d.2: PCI INT C disabled [ 0.291198] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.291219] pci 0000:00:1d.7: PCI INT A disabled [ 0.291258] pci 0000:01:00.0: Boot video device [ 0.291273] PCI: CLS 4 bytes, default 64 [ 0.291857] audit: initializing netlink socket (disabled) [ 0.291876] type=2000 audit(1336753420.284:1): initialized [ 0.337724] highmem bounce pool size: 64 pages [ 0.337734] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.349241] VFS: Disk quotas dquot_6.5.2 [ 0.349365] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.350418] fuse init (API version 7.17) [ 0.350611] msgmni has been set to 1685 [ 0.351179] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.351229] io scheduler noop registered [ 0.351233] io scheduler deadline registered [ 0.351247] io scheduler cfq registered (default) [ 0.351450] pcieport 0000:00:01.0: setting latency timer to 64 [ 0.351502] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X [ 0.351585] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.351639] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X [ 0.351728] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.351779] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X [ 0.351875] pcieport 0000:00:1c.5: setting latency timer to 64 [ 0.351927] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X [ 0.352094] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.352143] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.352311] intel_idle: MWAIT substates: 0x22220 [ 0.352315] intel_idle: does not run on family 6 model 23 [ 0.352446] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0 [ 0.352455] ACPI: Power Button [PWRB] [ 0.352556] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1 [ 0.352562] ACPI: Power Button [PWRF] [ 0.352650] ACPI: Fan [FAN] (on) [ 0.355667] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.355673] ACPI: Thermal Zone [THRM] (26 C) [ 0.355750] ERST: Table is not found! [ 0.355753] GHES: HEST is not enabled! [ 0.355898] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.376332] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.376582] isapnp: Scanning for PnP cards... [ 0.709133] Freeing initrd memory: 13792k freed [ 0.729743] isapnp: No Plug & Play device found [ 0.816786] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.832385] Linux agpgart interface v0.103 [ 0.835605] brd: module loaded [ 0.837138] loop: module loaded [ 0.837452] ata_piix 0000:00:1f.2: version 2.13 [ 0.837473] ata_piix 0000:00:1f.2: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.837480] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.837546] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.838099] scsi0 : ata_piix [ 0.838253] scsi1 : ata_piix [ 0.839183] ata1: SATA max UDMA/133 cmd 0xf900 ctl 0xf800 bmdma 0xf500 irq 19 [ 0.839192] ata2: SATA max UDMA/133 cmd 0xf700 ctl 0xf600 bmdma 0xf508 irq 19 [ 0.839239] ata_piix 0000:00:1f.5: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 0.839246] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.839300] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.839708] scsi2 : ata_piix [ 0.839841] scsi3 : ata_piix [ 0.840301] ata3: SATA max UDMA/133 cmd 0xf200 ctl 0xf100 bmdma 0xee00 irq 19 [ 0.840308] ata4: SATA max UDMA/133 cmd 0xf000 ctl 0xef00 bmdma 0xee08 irq 19 [ 0.840429] pata_acpi 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.840467] pata_acpi 0000:03:00.0: setting latency timer to 64 [ 0.840488] pata_acpi 0000:03:00.0: PCI INT A disabled [ 0.841159] Fixed MDIO Bus: probed [ 0.841205] tun: Universal TUN/TAP device driver, 1.6 [ 0.841210] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.841322] PPP generic driver version 2.4.2 [ 0.841515] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.841542] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.841567] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.841573] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.841658] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.845582] ehci_hcd 0000:00:1a.7: cache line size of 4 is not supported [ 0.845610] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xfdfff000 [ 0.860022] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.860264] hub 1-0:1.0: USB hub found [ 0.860272] hub 1-0:1.0: 6 ports detected [ 0.860404] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.860424] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.860430] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.860512] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.864413] ehci_hcd 0000:00:1d.7: cache line size of 4 is not supported [ 0.864438] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfdffe000 [ 0.880021] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.880227] hub 2-0:1.0: USB hub found [ 0.880234] hub 2-0:1.0: 6 ports detected [ 0.880369] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.880396] uhci_hcd: USB Universal Host Controller Interface driver [ 0.880431] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.880443] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.880449] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.880529] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.880574] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ff00 [ 0.880803] hub 3-0:1.0: USB hub found [ 0.880811] hub 3-0:1.0: 2 ports detected [ 0.880929] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.880940] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.880946] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.881039] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.881081] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000fe00 [ 0.881302] hub 4-0:1.0: USB hub found [ 0.881310] hub 4-0:1.0: 2 ports detected [ 0.881427] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.881438] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.881443] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.881523] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.881551] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000fd00 [ 0.881774] hub 5-0:1.0: USB hub found [ 0.881781] hub 5-0:1.0: 2 ports detected [ 0.881899] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.881910] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.881915] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.881993] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.882021] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000fc00 [ 0.882244] hub 6-0:1.0: USB hub found [ 0.882252] hub 6-0:1.0: 2 ports detected [ 0.882370] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.882381] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.882386] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.882467] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.882495] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000fb00 [ 0.882735] hub 7-0:1.0: USB hub found [ 0.882742] hub 7-0:1.0: 2 ports detected [ 0.882858] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.882869] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.882875] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.882954] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.882982] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000fa00 [ 0.883205] hub 8-0:1.0: USB hub found [ 0.883213] hub 8-0:1.0: 2 ports detected [ 0.883435] usbcore: registered new interface driver libusual [ 0.883535] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.883926] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.883936] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.884187] mousedev: PS/2 mouse device common for all mice [ 0.884433] rtc_cmos 00:03: RTC can wake from S4 [ 0.884582] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 0.884612] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs [ 0.884719] device-mapper: uevent: version 1.0.3 [ 0.884854] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 0.884917] EISA: Probing bus 0 at eisa.0 [ 0.884921] EISA: Cannot allocate resource for mainboard [ 0.884925] Cannot allocate resource for EISA slot 1 [ 0.884929] Cannot allocate resource for EISA slot 2 [ 0.884932] Cannot allocate resource for EISA slot 3 [ 0.884936] Cannot allocate resource for EISA slot 4 [ 0.884940] Cannot allocate resource for EISA slot 5 [ 0.884943] Cannot allocate resource for EISA slot 6 [ 0.884947] Cannot allocate resource for EISA slot 7 [ 0.884950] Cannot allocate resource for EISA slot 8 [ 0.884954] EISA: Detected 0 cards. [ 0.884969] cpufreq-nforce2: No nForce2 chipset. [ 0.884973] cpuidle: using governor ladder [ 0.884976] cpuidle: using governor menu [ 0.884980] EFI Variables Facility v0.08 2004-May-17 [ 0.885476] TCP cubic registered [ 0.885708] NET: Registered protocol family 10 [ 0.886771] NET: Registered protocol family 17 [ 0.886799] Registering the dns_resolver key type [ 0.886837] Using IPI No-Shortcut mode [ 0.887028] PM: Hibernation image not present or could not be loaded. [ 0.887047] registered taskstats version 1 [ 0.902579] Magic number: 12:339:388 [ 0.902592] usb usb6: hash matches [ 0.902687] rtc_cmos 00:03: setting system clock to 2012-05-11 16:23:41 UTC (1336753421) [ 0.903185] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.903189] EDD information not available. [ 1.170710] ata3: SATA link down (SStatus 0 SControl 300) [ 1.181439] ata4: SATA link down (SStatus 0 SControl 300) [ 1.288020] Refined TSC clocksource calibration: 2499.999 MHz. [ 1.288028] Switching to clocksource tsc [ 1.292016] usb 1-5: new high-speed USB device number 3 using ehci_hcd [ 1.486745] ata2.00: SATA link down (SStatus 0 SControl 300) [ 1.486762] ata2.01: SATA link down (SStatus 0 SControl 300) [ 1.640115] ata1.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.640130] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.648342] ata1.00: ATA-7: Maxtor 7Y250M0, YAR511W0, max UDMA/133 [ 1.648348] ata1.00: 490234752 sectors, multi 0: LBA48 [ 1.664325] ata1.00: configured for UDMA/133 [ 1.664531] scsi 0:0:0:0: Direct-Access ATA Maxtor 7Y250M0 YAR5 PQ: 0 ANSI: 5 [ 1.664745] sd 0:0:0:0: [sda] 490234752 512-byte logical blocks: (251 GB/233 GiB) [ 1.664809] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.664838] sd 0:0:0:0: [sda] Write Protect is off [ 1.664843] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.664884] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.691699] sda: sda1 sda2 sda3 sda4 [ 1.692348] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.692461] Freeing unused kernel memory: 740k freed [ 1.692820] Write protecting the kernel text: 5828k [ 1.692851] Write protecting the kernel read-only data: 2376k [ 1.692854] NX-protecting the kernel data: 4412k [ 1.723980] udevd[92]: starting version 175 [ 1.865339] Floppy drive(s): fd0 is 1.44M [ 1.865429] pata_jmicron 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.865478] pata_jmicron 0000:03:00.0: setting latency timer to 64 [ 1.867875] sky2: driver version 1.30 [ 1.867926] sky2 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1.867942] sky2 0000:04:00.0: setting latency timer to 64 [ 1.867979] sky2 0000:04:00.0: Yukon-2 EC chip revision 2 [ 1.868111] sky2 0000:04:00.0: irq 44 for MSI/MSI-X [ 1.868174] scsi4 : pata_jmicron [ 1.869802] sky2 0000:04:00.0: eth0: addr 00:01:29:a4:16:0a [ 1.869828] scsi5 : pata_jmicron [ 1.869943] ata5: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 16 [ 1.869949] ata6: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 16 [ 1.880053] usb 4-1: new full-speed USB device number 2 using uhci_hcd [ 1.884052] FDC 0 is a post-1991 82077 [ 2.032611] ata5.00: ATAPI: _NEC DVD+/-RW ND-3450A, 103C, max UDMA/33 [ 2.048585] ata5.00: configured for UDMA/33 [ 2.049777] scsi 4:0:0:0: CD-ROM _NEC DVD+-RW ND-3450A 103C PQ: 0 ANSI: 5 [ 2.051048] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray [ 2.051054] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 2.051283] sr 4:0:0:0: Attached scsi CD-ROM sr0 [ 2.051483] sr 4:0:0:0: Attached scsi generic sg1 type 5 [ 2.079838] usbcore: registered new interface driver usbhid [ 2.079844] usbhid: USB HID core driver [ 2.236660] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 12.150230] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 12.177342] udevd[333]: starting version 175 [ 12.195524] Adding 417684k swap on /dev/sda2. Priority:-1 extents:1 across:417684k [ 12.278032] lp: driver loaded but no devices found [ 12.516456] logitech-djreceiver 0003:046D:C52B.0003: hiddev0,hidraw0: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1a.1-1/input2 [ 12.520297] input: Logitech Unifying Device. Wireless PID:1024 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input2 [ 12.520753] logitech-djdevice 0003:046D:C52B.0004: input,hidraw1: USB HID v1.11 Mouse [Logitech Unifying Device. Wireless PID:1024] on usb-0000:00:1a.1-1:1 [ 12.523286] input: Logitech Unifying Device. Wireless PID:2011 as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.2/0003:046D:C52B.0003/input/input3 [ 12.524439] logitech-djdevice 0003:046D:C52B.0005: input,hidraw2: USB HID v1.11 Keyboard [Logitech Unifying Device. Wireless PID:2011] on usb-0000:00:1a.1-1:2 [ 12.545746] type=1400 audit(1336771433.137:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=502 comm="apparmor_parser" [ 12.546574] type=1400 audit(1336771433.137:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=502 comm="apparmor_parser" [ 12.547034] type=1400 audit(1336771433.137:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=502 comm="apparmor_parser" [ 12.626869] Linux video capture interface: v2.00 [ 12.649104] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081a) [ 12.668665] input: UVC Camera (046d:081a) as /devices/pci0000:00/0000:00:1a.7/usb1/1-5/1-5:1.0/input/input4 [ 12.668909] usbcore: registered new interface driver uvcvideo [ 12.668914] USB Video Class driver (1.1.1) [ 12.697645] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 12.697721] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X [ 12.697760] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 12.706772] nvidia: module license 'NVIDIA' taints kernel. [ 12.706778] Disabling lock debugging due to kernel taint [ 12.735428] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 13.350252] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 13.350267] nvidia 0000:01:00.0: setting latency timer to 64 [ 13.350275] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem [ 13.351464] NVRM: loading NVIDIA UNIX x86 Kernel Module 295.40 Thu Apr 5 21:28:09 PDT 2012 [ 13.356785] hda_codec: ALC889A: BIOS auto-probing. [ 13.357267] init: failsafe main process (658) killed by TERM signal [ 13.372756] input: HDA Intel Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5 [ 13.373173] input: HDA Intel Front Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 13.373568] input: HDA Intel Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 13.373954] input: HDA Intel Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8 [ 13.374339] input: HDA Intel Line-Out Side as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9 [ 13.374715] input: HDA Intel Line-Out CLFE as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10 [ 13.375109] input: HDA Intel Line-Out Surround as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11 [ 13.375724] input: HDA Intel Line-Out Front as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12 [ 13.475252] type=1400 audit(1336771434.065:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=735 comm="apparmor_parser" [ 13.477026] type=1400 audit(1336771434.069:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=735 comm="apparmor_parser" [ 13.477695] type=1400 audit(1336771434.069:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=735 comm="apparmor_parser" [ 13.479048] type=1400 audit(1336771434.069:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=734 comm="apparmor_parser" [ 13.488994] type=1400 audit(1336771434.081:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=738 comm="apparmor_parser" [ 13.489972] type=1400 audit(1336771434.081:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=738 comm="apparmor_parser" [ 13.

  Read the article

• GRUB doesn't recognize partitions on one harddisk

  - by knizz

  I have a dualboot computer with Windows Vista (on hd0) and Ubuntu 9.10. The bootloader is GRUB and the windows bootloader lets me decide between Vista and Ubuntu-Installation (broken WuBi). But now (i don't know why that changed) I can't use start the windows-bootloader anymore. I tried "ls" on the grub-prompt and it gave me a list like: (hd0) (hd1) (hd1,0) (hd1,1) (hd1,2) ... (fd0) It recognizes all partitions of hd1 (the ubuntu-harddisk) but not of hd0(the win-disk). .. WHY? Here is the result of the "boot info script" for the technical details: Boot Info Script 0.55 dated February 15th, 2010 ============================= Boot Info Summary: ============================== => Grub 2 is installed in the MBR of /dev/sda and looks for (UUID=a7c510e3-2399-437b-ab92-fa609e48d63f)/boot/grub. => No boot loader is installed in the MBR of /dev/sdb sda1: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows Vista Boot files/dirs: /bootmgr /Boot/BCD /Windows/System32/winload.exe /wubildr.mbr /wubildr sda2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: sdb1: _________________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unbekannter Dateisystemtyp „“ sdb2: _________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files/dirs: sdb3: _________________________________________________________________________ File system: Bios Boot Partition Boot sector type: - Boot sector info: sdb4: _________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 9.10 Boot files/dirs: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb5: _________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: =========================== Drive/Partition Info: ============================= Drive: sda ___________________ _____________________________________________________ Platte /dev/sda: 640.1 GByte, 640135028736 Byte 255 Köpfe, 63 Sektoren/Spuren, 77825 Zylinder, zusammen 1250263728 Sektoren Einheiten = Sektoren von 1 × 512 = 512 Bytes Disk identifier: 0x52554d66 Partition Boot Start End Size Id System /dev/sda1 * 2,048 307,202,047 307,200,000 7 HPFS/NTFS /dev/sda2 307,202,048 1,250,258,943 943,056,896 7 HPFS/NTFS Drive: sdb ___________________ _____________________________________________________ Platte /dev/sdb: 640.1 GByte, 640135028736 Byte 255 Köpfe, 63 Sektoren/Spuren, 77825 Zylinder, zusammen 1250263728 Sektoren Einheiten = Sektoren von 1 × 512 = 512 Bytes Disk identifier: 0x00000000 Partition Boot Start End Size Id System /dev/sdb1 1 1,250,263,727 1,250,263,727 ee GPT GUID Partition Table detected. Partition Start End Size System /dev/sdb1 34 262,177 262,144 Microsoft Windows /dev/sdb2 262,178 1,131,253,933 1,130,991,756 Linux or Data /dev/sdb3 1,131,253,934 1,131,255,887 1,954 Bios Boot Partition /dev/sdb4 1,131,255,888 1,245,312,528 114,056,641 Linux or Data /dev/sdb5 1,245,312,529 1,250,263,694 4,951,166 Linux Swap blkid -c /dev/null: ____________________________________________________________ Device UUID TYPE LABEL /dev/sda1 AE1440441440122F ntfs /dev/sda2 3AE66E4DE66E0A09 ntfs data /dev/sdb2 5419D16119DAA4DE ntfs LaufwerkD /dev/sdb4 a7c510e3-2399-437b-ab92-fa609e48d63f ext4 /dev/sdb5 60a0143a-e01b-450a-bbd1-f22059e47b65 swap ============================ "mount | grep ^/dev output: =========================== Device Mount_Point Type Options /dev/sdb4 / ext4 (rw,errors=remount-ro) =========================== sdb4/boot/grub/grub.cfg: =========================== # # DO NOT EDIT THIS FILE # # It is automatically generated by /usr/sbin/grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s /boot/grub/grubenv ]; then have_grubenv=true load_env fi set default="0" if [ ${prev_saved_entry} ]; then saved_entry=${prev_saved_entry} save_env saved_entry prev_saved_entry= save_env prev_saved_entry fi insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=640x480 insmod gfxterm insmod vbe if terminal_output gfxterm ; then true ; else # For backward compatibility with versions of terminal.mod that don't # understand terminal_output terminal gfxterm fi fi if [ ${recordfail} = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/white ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### menuentry "Ubuntu, Linux 2.6.31-20-generic" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi set quiet=1 insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-20-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro quiet splash initrd /boot/initrd.img-2.6.31-20-generic } menuentry "Ubuntu, Linux 2.6.31-20-generic (recovery mode)" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-20-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro single initrd /boot/initrd.img-2.6.31-20-generic } menuentry "Ubuntu, Linux 2.6.31-14-generic" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi set quiet=1 insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-14-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro quiet splash initrd /boot/initrd.img-2.6.31-14-generic } menuentry "Ubuntu, Linux 2.6.31-14-generic (recovery mode)" { recordfail=1 if [ -n ${have_grubenv} ]; then save_env recordfail; fi insmod ext2 set root=(hd1,4) search --no-floppy --fs-uuid --set a7c510e3-2399-437b-ab92-fa609e48d63f linux /boot/vmlinuz-2.6.31-14-generic root=UUID=a7c510e3-2399-437b-ab92-fa609e48d63f ro single initrd /boot/initrd.img-2.6.31-14-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows Vista (loader) (on /dev/sda1)" { insmod ntfs set root=(hd0,1) search --no-floppy --fs-uuid --set ae1440441440122f chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### =============================== sdb4/etc/fstab: =============================== # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 # / was on /dev/sdb4 during installation UUID=a7c510e3-2399-437b-ab92-fa609e48d63f / ext4 errors=remount-ro 0 1 # swap was on /dev/sdb5 during installation UUID=60a0143a-e01b-450a-bbd1-f22059e47b65 none swap sw 0 0 /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0 =================== sdb4: Location of files loaded by Grub: =================== 583.8GB: boot/grub/core.img 583.8GB: boot/grub/grub.cfg 579.7GB: boot/initrd.img-2.6.31-14-generic 580.0GB: boot/initrd.img-2.6.31-20-generic 579.7GB: boot/vmlinuz-2.6.31-14-generic 579.8GB: boot/vmlinuz-2.6.31-20-generic 580.0GB: initrd.img 579.7GB: initrd.img.old 579.8GB: vmlinuz 579.7GB: vmlinuz.old =========================== Unknown MBRs/Boot Sectors/etc ======================= Unknown BootLoader on sdb1 00000000 54 34 dc 3b 8b ff 6c fa 3e 59 3d 24 25 af 5f 9b |T4.;..l.>Y=$%._.| 00000010 72 f8 36 3d 56 30 22 fd c6 08 5e 39 7f dc 29 48 |r.6=V0"...^9..)H| 00000020 48 e5 24 52 77 b0 fc 64 b6 ce 48 c3 07 ce b5 81 |H.$Rw..d..H.....| 00000030 06 68 60 4f 6e fb 83 92 df 3a 54 b9 df 21 2a cd |.h`On....:T..!*.| 00000040 1e 2f e2 49 fe cf 81 2d 52 17 1a 4e 66 b4 f3 f0 |./.I...-R..Nf...| 00000050 41 25 e3 96 26 28 fe 19 61 72 75 f8 40 a3 b7 ef |A%..&(..aru.@...| 00000060 5f 79 dc cb 28 44 44 7c 9b 9a 7b 6c 4b 4b 60 0f |_y..(DD|..{lKK`.| 00000070 a9 97 87 bc 85 9f db bb d2 1a 88 9f aa 49 18 d5 |.............I..| 00000080 92 2d db 7e fe f7 8d 7a 18 c0 33 c5 bd 7a 46 07 |.-.~...z..3..zF.| 00000090 c8 27 13 66 94 49 62 9f bc 99 56 55 25 fb 94 a9 |.'.f.Ib...VU%...| 000000a0 3f b2 a7 0a 87 d0 a4 4e 51 f1 09 02 c4 29 eb ff |?......NQ....)..| 000000b0 26 3b 51 3e 5a 0c db ee a6 57 a7 c3 ba a1 74 90 |&;Q>Z....W....t.| 000000c0 ee 70 08 18 cc b8 d0 22 ce 96 c7 cb 68 40 98 20 |.p....."....h@. | 000000d0 49 3d 07 ec df d1 8d cf 19 bc 42 90 70 24 01 b4 |I=........B.p$..| 000000e0 28 cf c6 50 d3 95 5a 1b 18 15 33 c7 b2 a8 95 92 |(..P..Z...3.....| 000000f0 bb 93 fe 18 2b 81 c1 6b 9c 30 f1 65 50 6a 80 3d |....+..k.0.ePj.=| 00000100 74 37 a8 59 a6 51 8a 63 b6 d8 16 9f a9 47 2a 7c |t7.Y.Q.c.....G*|| 00000110 04 a7 fe 69 47 02 bf e9 b7 1b 7a ea 60 5c 3c 53 |...iG.....z.`\<S| 00000120 5b 10 78 dc 4d d2 a8 22 30 45 37 fb 56 06 9f 06 |[.x.M.."0E7.V...| 00000130 aa df cf 87 3a 3e cf 72 f2 e5 a6 c6 aa e2 7c 1c |....:>.r......|.| 00000140 64 c2 fc 80 ce 02 fc 7f 0f c6 60 81 bf cd 3b 5a |d.........`...;Z| 00000150 37 a5 38 1b 0c 1b 39 2e d6 f6 3d a2 36 e5 87 c3 |7.8...9...=.6...| 00000160 17 b5 fd ee 33 c7 ce a3 d9 c2 57 dc ee 85 48 9d |....3.....W...H.| 00000170 33 60 02 cd c5 83 44 44 ea b6 07 25 0a 4b a6 6e |3`....DD...%.K.n| 00000180 fc 51 42 cd 84 0b 65 b6 19 a1 e5 b2 eb 14 0c fa |.QB...e.........| 00000190 24 77 f5 44 6e 5d 39 dd b6 8e cc f8 30 fe 21 46 |$w.Dn]9.....0.!F| 000001a0 9c ff 95 c6 c7 b5 0a df 54 ca d2 ac bc 64 d0 97 |........T....d..| 000001b0 94 54 d9 29 0f 91 60 20 c3 e4 53 c2 b0 e4 40 72 |.T.)..` ..S...@r| 000001c0 7e 25 bc 81 06 ad 05 46 14 a7 e6 71 6b 5c db 9c |~%.....F...qk\..| 000001d0 0a 5e 76 23 ae 06 01 36 98 21 65 2c 90 e7 4b 1a |.^v#...6.!e,..K.| 000001e0 2a 2d 80 a5 48 db 9e 14 e0 9f e9 aa 00 e3 77 32 |*-..H.........w2| 000001f0 0f fd 94 db 55 a6 64 46 be ae ca de da ee 89 68 |....U.dF.......h| 00000200 =======Devices which don't seem to have a corresponding hard drive============== sdc sdd sde

  Read the article

• How does Windows 7 DNS client work?

  - by Mark Allison

  I am using a local DHCP and DNS server on my home network on a linux machine. It is running CentOS 6.3 with dnsmasq 2.48. It's all working fine except for local DNS lookups for Windows machines only. I have a mix of Ubuntu, CentOS and Windows machines on the network, some virtual, some physical. I have a machine called boron and the domain is called localdomain If I ping boron from any linux machine, I get [root@lithium lists]# ping -c3 boron PING boron.localdomain (10.0.0.5) 56(84) bytes of data. 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=1 ttl=64 time=0.740 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=2 ttl=64 time=0.478 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=3 ttl=64 time=0.458 ms --- boron.localdomain ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.458/0.558/0.740/0.131 ms If I do it from my Windows 7 machine, I get: Ping request could not find host boron. Please check the name and try again. If I try ping boron.localdomain I get: Pinging boron.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=16ms TTL=57 Reply from 67.215.65.132: bytes=32 time=188ms TTL=57 Reply from 67.215.65.132: bytes=32 time=15ms TTL=57 Reply from 67.215.65.132: bytes=32 time=14ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 14ms, Maximum = 188ms, Average = 58ms which is clearly wrong. Why is it going out to the internet? Why can't my windows machine resolve the boron hostname to a FQDN? My Windows machines and linux machines get their network config from DHCP. UPDATE If I do ipconfig /all in Windows, it looks as I would expect: Windows IP Configuration Host Name . . . . . . . . . . . . : lanthanum Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : .localdomain Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : .localdomain Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 50-E5-49-38-FC-A2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.0.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 23 August 2012 13:58:45 Lease Expires . . . . . . . . . . : 24 August 2012 07:58:48 Default Gateway . . . . . . . . . : 10.0.0.6 DHCP Server . . . . . . . . . . . : 10.0.0.6 DNS Servers . . . . . . . . . . . : 10.0.0.6 208.67.222.222 208.67.220.220 NetBIOS over Tcpip. . . . . . . . : Enabled When I do an nslookup I get: Server: carbon.localdomain Address: 10.0.0.6 *** carbon.localdomain can't find boron: Unspecified error However if I do ifconfig -a in Linux I get: [root@nitrogen ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:EC:2A inet addr:10.0.0.7 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:187687 errors:0 dropped:0 overruns:0 frame:0 TX packets:5857 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23910700 (22.8 MiB) TX bytes:712964 (696.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:329894 errors:0 dropped:0 overruns:0 frame:0 TX packets:329894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:67153143 (64.0 MiB) TX bytes:67153143 (64.0 MiB) and nslookup: [root@nitrogen ~]# nslookup boron Server: 10.0.0.6 Address: 10.0.0.6#53 Name: boron Address: 10.0.0.5 Both machines are on the same network using the same DHCP server. UPDATE 2 I thought the issue was resolved but I am getting intermittent DNS resolving issues but only on my Windows 7 machine. All my linux boxes are fine. This is what happens when I ping and nslookup from Windows to a Windows 2008 Server: C:\Users\mark>nslookup magnesium Server: carbon.localdomain Address: 10.0.0.6 Name: magnesium.localdomain Address: 10.0.0.12 C:\Users\mark>ping magnesium Pinging magnesium.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=267ms TTL=57 Reply from 67.215.65.132: bytes=32 time=162ms TTL=57 Reply from 67.215.65.132: bytes=32 time=510ms TTL=57 Reply from 67.215.65.132: bytes=32 time=146ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 146ms, Maximum = 510ms, Average = 271ms And from Linux: [root@beryllium ~]# ping -c4 magnesium PING magnesium.localdomain (10.0.0.12) 56(84) bytes of data. 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=1 ttl=128 time=0.176 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=2 ttl=128 time=0.634 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=3 ttl=128 time=0.685 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=4 ttl=128 time=0.263 ms --- magnesium.localdomain ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3002ms rtt min/avg/max/mdev = 0.176/0.439/0.685/0.223 ms [root@beryllium ~]# nslookup magnesium Server: 10.0.0.6 Address: 10.0.0.6#53 Name: magnesium.localdomain Address: 10.0.0.12 UPDATE 3 I stopped the Windows DNS client on my Windows 7 machine with net stop dnscache and it is now working fine. It would be nice to get DNS working with the DNS client on, but I might be OK without it, what do you think?

  Read the article

• Form contents not showing in email

  - by fmz

  This is a followup to a question I posted yesterday. I thought everything was working fine, but today, I am not getting any results in the email from the drop down field. Here is the form code in question: <label for="purpose"><span class="required">*</span> Purpose</label> <select id="purpose" name="purpose" style="width: 300px; height:35px;"> <option value="" selected="selected">-- Select One --</option> <option value="I am interested in your services">I am interested in your services!</option> <option value="I am interested in a partnership">I am interested in a partnership!</option> <option value="I am interested in a job">I am interested in a job!</option> </select> It is then processed in PHP and should output the selected option to an email, however the Reason for Contact line always comes through with nothing in it. Here is the PHP code: <?php if(!$_POST) exit; $name = $_POST['name']; $company = $_POST['company']; $email = $_POST['email']; $phone = $_POST['phone']; $purpose = $_POST['purpose']; $comments = $_POST['comments']; $verify = $_POST['verify']; if(trim($name) == '') { echo '<div class="error_message">Attention! You must enter your name.</div>'; exit(); } else if(trim($email) == '') { echo '<div class="error_message">Attention! Please enter a valid email address.</div>'; exit(); } else if(trim($phone) == '') { echo '<div class="error_message">Attention! Please enter a valid phone number.</div>'; exit(); } else if(!isEmail($email)) { echo '<div class="error_message">Attention! You have enter an invalid e-mail address, try again.</div>'; exit(); } if(trim($comments) == '') { echo '<div class="error_message">Attention! Please enter your message.</div>'; exit(); } else if(trim($verify) == '') { echo '<div class="error_message">Attention! Please enter the verification number.</div>'; exit(); } else if(trim($verify) != '4') { echo '<div class="error_message">Attention! The verification number you entered is incorrect.</div>'; exit(); } if($error == '') { if(get_magic_quotes_gpc()) { $comments = stripslashes($comments); } // Configuration option. // Enter the email address that you want to emails to be sent to. // Example $address = "[email protected]"; $address = "[email protected]"; // Configuration option. // i.e. The standard subject will appear as, "You've been contacted by John Doe." // Example, $e_subject = '$name . ' has contacted you via Your Website.'; $e_subject = 'You\'ve been contacted by ' . $name . '.'; // Configuration option. // You can change this if you feel that you need to. // Developers, you may wish to add more fields to the form, in which case you must be sure to add them here. $e_body = "You have been contacted by $name.\r\n\n"; $e_company = "Company: $company\r\n\n"; $e_content = "Comments: \"$comments\"\r\n\n"; $e_purpose = "Reason for contact: $purpose\r\n\n"; $e_reply = "You can contact $name via email, $email or via phone $phone"; $msg = $e_body . $e_content . $e_company . $e_purpose . $e_reply; if(mail($address, $e_subject, $msg, "From: $email\r\nReply-To: $email\r\nReturn-Path: $email\r\n")) { // Email has sent successfully, echo a success page. echo "<fieldset>"; echo "<div id='success_page'>"; echo "<h1>Email Sent Successfully.</h1>"; echo "<p>Thank you <strong>$name</strong>, your message has been submitted to us.</p>"; echo "</div>"; echo "</fieldset>"; } else { echo 'ERROR!'; } } function isEmail($email) { // Email address verification, do not edit. return(preg_match("/^[-_.[:alnum:]]+@((([[:alnum:]]|[[:alnum:]][[:alnum:]-]*[[:alnum:]])\.)+(ad|ae|aero|af|ag|ai|al|am|an|ao|aq|ar|arpa|as|at|au|aw|az|ba|bb|bd|be|bf|bg|bh|bi|biz|bj|bm|bn|bo|br|bs|bt|bv|bw|by|bz|ca|cc|cd|cf|cg|ch|ci|ck|cl|cm|cn|co|com|coop|cr|cs|cu|cv|cx|cy|cz|de|dj|dk|dm|do|dz|ec|edu|ee|eg|eh|er|es|et|eu|fi|fj|fk|fm|fo|fr|ga|gb|gd|ge|gf|gh|gi|gl|gm|gn|gov|gp|gq|gr|gs|gt|gu|gw|gy|hk|hm|hn|hr|ht|hu|id|ie|il|in|info|int|io|iq|ir|is|it|jm|jo|jp|ke|kg|kh|ki|km|kn|kp|kr|kw|ky|kz|la|lb|lc|li|lk|lr|ls|lt|lu|lv|ly|ma|mc|md|mg|mh|mil|mk|ml|mm|mn|mo|mp|mq|mr|ms|mt|mu|museum|mv|mw|mx|my|mz|na|name|nc|ne|net|nf|ng|ni|nl|no|np|nr|nt|nu|nz|om|org|pa|pe|pf|pg|ph|pk|pl|pm|pn|pr|pro|ps|pt|pw|py|qa|re|ro|ru|rw|sa|sb|sc|sd|se|sg|sh|si|sj|sk|sl|sm|sn|so|sr|st|su|sv|sy|sz|tc|td|tf|tg|th|tj|tk|tm|tn|to|tp|tr|tt|tv|tw|tz|ua|ug|uk|um|us|uy|uz|va|vc|ve|vg|vi|vn|vu|wf|ws|ye|yt|yu|za|zm|zw)$|(([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5])\.){3}([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5]))$/i",$email)); } ?> Any assistance would be greatly appreciated. Thanks!

  Read the article

• deadlocks in the innodb status

  - by shantanuo

  Mysql sever has suddenly become very slow. There are no queries in the slow query log but the innodb status shows something like the following. Does it mean that it is due to innodb deadlock? if Yes, what is the way out? *************************** 1. row *************************** Status: ===================================== 100315 12:55:29 INNODB MONITOR OUTPUT ===================================== Per second averages calculated from the last 5 seconds ---------- SEMAPHORES ---------- OS WAIT ARRAY INFO: reservation count 187532, signal count 188120 Mutex spin waits 0, rounds 61908654, OS waits 33052 RW-shared spins 89241, OS waits 41948; RW-excl spins 5857, OS waits 1557 ------------------------ LATEST DETECTED DEADLOCK ------------------------ 100315 12:43:02 *** (1) TRANSACTION: TRANSACTION 0 56996536, ACTIVE 0 sec, process no 5000, OS thread id 3031395216 starting index read mysql tables in use 1, locked 1 LOCK WAIT 6 lock struct(s), heap size 1024, undo log entries 6 MySQL thread id 994, query id 7699751 localhost application Searching rows for update UPDATE QUERY *** (1) WAITING FOR THIS LOCK TO BE GRANTED: RECORD LOCKS space id 0 page no 4073 n bits 296 index `PRIMARY` of table `dbII/tbl_ticket_block_master` trx id 0 56996536 lock_mode X locks r ec but not gap waiting Record lock, heap no 141 PHYSICAL RECORD: n_fields 23; compact format; info bits 0 0: len 7; hex 33353837393936; asc 3587996;; 1: len 4; hex 800001f4; asc ;; 2: len 1; hex 47; asc G;; 3: len 2; hex 6f6b; asc ok;; 4: le n 6; hex 0000035957fe; asc YW ;; 5: len 7; hex 000000401737c0; asc @ 7 ;; 6: SQL NULL; 7: SQL NULL; 8: SQL NULL; 9: len 3; hex 8fb46e; asc n;; 10: SQL NULL; 11: len 1; hex 30; asc 0;; 12: len 0; hex ; asc ;; 13: SQL NULL; 14: len 1; hex 33; asc 3;; 15: len 4; hex 4b9ceebe ; asc K ;; 16: len 1; hex 30; asc 0;; 17: len 4; hex 80006ae8; asc j ;; 18: len 0; hex ; asc ;; 19: len 0; hex ; asc ;; 20: len 0; hex ; asc ;; 21: len 0; hex ; asc ;; 22: len 0; hex ; asc ;; *** (2) TRANSACTION: TRANSACTION 0 56996527, ACTIVE 0 sec, process no 5000, OS thread id 2961476496 fetching rows, thread declared inside InnoDB 237 mysql tables in use 3, locked 3 121 lock struct(s), heap size 11584, undo log entries 16 MySQL thread id 995, query id 7699729 localhost application Searching rows for update UPDATE QUERY *** (2) HOLDS THE LOCK(S): RECORD LOCKS space id 0 page no 4073 n bits 296 index `PRIMARY` of table `DBII/tbl_ticket_block_master` trx id 0 56996527 lock_mode X Record lock, heap no 1 PHYSICAL RECORD: n_fields 1; compact format; info bits 0 0: len 8; hex 73757072656d756d; asc supremum;; Record lock, heap no 2 PHYSICAL RECORD: n_fields 23; compact format; info bits 0 0: len 7; hex 33353837343631; asc 3587461;; 1: len 4; hex 800001f4; asc ;; 2: len 1; hex 47; asc G;; 3: len 6; hex 497373756564; asc Is sued;; 4: len 6; hex 000003425295; asc BR ;; 5: len 7; hex 8000000464012c; asc d ,;; 6: SQL NULL; 7: len 4; hex 80000058; asc X;; 8: len 1; hex 43; asc C;; 9: len 3; hex 8fb465; asc e;; 10: len 3; hex 8fb46d; asc m;; 11: len 1; hex 30; asc 0;; 12: len 0; hex ; asc ; ; 13: SQL NULL; 14: len 1; hex 33; asc 3;; 15: len 4; hex 4b9b33a2; asc K 3 ;; 16: len 3; hex 756d67; asc umg;; 17: len 4; hex 80006744; asc gD;; 18: len 0; hex ; asc ;; 19: len 0; hex ; asc ;; 20: len 0; hex ; asc ;; 21: len 0; hex ; asc ;; 22: len 0; hex ; asc ;;

  Read the article

• Getting Selected Dropdown content to show in a form-generated email

  - by fmz

  I have a small contact form: <form method="post" action="contact.php" name="contactform" id="contactform"> <fieldset> <legend>Please fill in the following form to contact us</legend> <label for="name"><span class="required">*</span> Your Name</label> <input name="name" type="text" id="name" size="30" value="" /> <br /> <label for="company"><span class="required">*</span> Company</label> <input name="company" type="text" id="name" size="30" value="" /> <br /> <label for="email"><span class="required">*</span> Email</label> <input name="email" type="text" id="email" size="30" value="" /> <br /> <label for="phone"><span class="required">*</span> Phone</label> <input name="phone" type="text" id="phone" size="30" value="" /> <br /> <label for="purpose"><span class="required">*</span> Purpose</label> <select id="purpose" style="width: 300px; height:35px;"> <option value="I am interested in your services">I am interested in your services!</option> <option value="I am interested in a partnership">I am interested in a partnership!</option> <option value="I am interested in a job">I am interested in a job!</option> </select> <br /> <label for=comments><span class="required">*</span> Comments</label> <textarea name="comments" cols="40" rows="3" id="comments" style="width: 350px;"></textarea> <p><span class="required">*</span> Please help us control spam.</p> <label for=verify accesskey=V>&nbsp;&nbsp;&nbsp;3 + 1 =</label> <input name="verify" type="text" id="verify" size="4" value="" style="width: 30px;" /><br /><br /> <input type="submit" class="submit" id="submit" value="Submit" /> </fieldset> </form> I want to send the results of the form in a php generated email. Everything is coming through except the selected contents of the "purpose" drop down. Here is the PHP: <?php if(!$_POST) exit; $name = $_POST['name']; $company = $_POST['company']; $email = $_POST['email']; $phone = $_POST['phone']; $purpose = $_POST['purpose']; $comments = $_POST['comments']; $verify = $_POST['verify']; if(trim($name) == '') { echo '<div class="error_message">Attention! You must enter your name.</div>'; exit(); } else if(trim($company) == '') { echo '<div class="error_message">Attention! Please enter your company name.</div>'; exit(); } else if(trim($email) == '') { echo '<div class="error_message">Attention! Please enter a valid email address.</div>'; exit(); } else if(trim($phone) == '') { echo '<div class="error_message">Attention! Please enter a valid phone number.</div>'; exit(); } else if(!isEmail($email)) { echo '<div class="error_message">Attention! You have enter an invalid e-mail address, try again.</div>'; exit(); } if(trim($comments) == '') { echo '<div class="error_message">Attention! Please enter your message.</div>'; exit(); } else if(trim($verify) == '') { echo '<div class="error_message">Attention! Please enter the verification number.</div>'; exit(); } else if(trim($verify) != '4') { echo '<div class="error_message">Attention! The verification number you entered is incorrect.</div>'; exit(); } if($error == '') { if(get_magic_quotes_gpc()) { $comments = stripslashes($comments); } // Configuration option. // Enter the email address that you want to emails to be sent to. // Example $address = "[email protected]"; $address = "[email protected]"; // Configuration option. // i.e. The standard subject will appear as, "You've been contacted by John Doe." // Example, $e_subject = '$name . ' has contacted you via Your Website.'; $e_subject = 'You\'ve been contacted by ' . $name . '.'; // Configuration option. // You can change this if you feel that you need to. // Developers, you may wish to add more fields to the form, in which case you must be sure to add them here. $e_body = "You have been contacted by $name.\r\n\n"; $e_content = "Comments: \"$comments\"\r\n\n"; $e_company = "Company: $company\r\n\n"; $e_purpose = "Reason for contact: $purpose\r\n"; $e_reply = "You can contact $name via email, $email or via phone $phone"; $msg = $e_body . $e_content . $e_company . $e_purpose . $e_reply; if(mail($address, $e_subject, $msg, "From: $email\r\nReply-To: $email\r\nReturn-Path: $email\r\n")) { // Email has sent successfully, echo a success page. echo "<fieldset>"; echo "<div id='success_page'>"; echo "<h1>Email Sent Successfully.</h1>"; echo "<p>Thank you <strong>$name</strong>, your message has been submitted to us.</p>"; echo "</div>"; echo "</fieldset>"; } else { echo 'ERROR!'; } } function isEmail($email) { // Email address verification, do not edit. return(preg_match("/^[-_.[:alnum:]]+@((([[:alnum:]]|[[:alnum:]][[:alnum:]-]*[[:alnum:]])\.)+(ad|ae|aero|af|ag|ai|al|am|an|ao|aq|ar|arpa|as|at|au|aw|az|ba|bb|bd|be|bf|bg|bh|bi|biz|bj|bm|bn|bo|br|bs|bt|bv|bw|by|bz|ca|cc|cd|cf|cg|ch|ci|ck|cl|cm|cn|co|com|coop|cr|cs|cu|cv|cx|cy|cz|de|dj|dk|dm|do|dz|ec|edu|ee|eg|eh|er|es|et|eu|fi|fj|fk|fm|fo|fr|ga|gb|gd|ge|gf|gh|gi|gl|gm|gn|gov|gp|gq|gr|gs|gt|gu|gw|gy|hk|hm|hn|hr|ht|hu|id|ie|il|in|info|int|io|iq|ir|is|it|jm|jo|jp|ke|kg|kh|ki|km|kn|kp|kr|kw|ky|kz|la|lb|lc|li|lk|lr|ls|lt|lu|lv|ly|ma|mc|md|mg|mh|mil|mk|ml|mm|mn|mo|mp|mq|mr|ms|mt|mu|museum|mv|mw|mx|my|mz|na|name|nc|ne|net|nf|ng|ni|nl|no|np|nr|nt|nu|nz|om|org|pa|pe|pf|pg|ph|pk|pl|pm|pn|pr|pro|ps|pt|pw|py|qa|re|ro|ru|rw|sa|sb|sc|sd|se|sg|sh|si|sj|sk|sl|sm|sn|so|sr|st|su|sv|sy|sz|tc|td|tf|tg|th|tj|tk|tm|tn|to|tp|tr|tt|tv|tw|tz|ua|ug|uk|um|us|uy|uz|va|vc|ve|vg|vi|vn|vu|wf|ws|ye|yt|yu|za|zm|zw)$|(([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5])\.){3}([0-9][0-9]?|[0-1][0-9][0-9]|[2][0-4][0-9]|[2][5][0-5]))$/i",$email)); } ?> What am I missing? Thanks.

  Read the article

• java inserting special characters with preparedstatement fails

  - by phill

  I am using an HTML form which sends <input type=hidden name=longdesc value='SMARTNET%^" 8X5XNBD'> this is done by the following javascript code: function masinsert(id) { var currentTime=new Date(); var button = document.getElementById("m"+id); button.onclick=""; button.value="Inserting"; var itemdescription = document.getElementById("itemdescription"+id).value; function handleHttpResponse() { if (http.readyState == 4) { button.value="Item Added"; } } var http = getHTTPObject(); // We create the HTTP Object var tempUrl = "\AInsert"; tempUrl += "itemdescription="+itemdescription+"&"+"itemshortdescription="+itemdescription.substring(0,37)+; alert(tempUrl); http.open("GET", tempUrl, true); http.onreadystatechange = handleHttpResponse; http.send(null); } to a java servlet. AInsert.java in the AInsert.java file, I do a String itemdescription = request.getParameter("longdesc"); which then sends the value to a preparedstatement to run an insert query. In the query, there are sometimes special characters which throw it off. For example, when I run the following insert into itemdescription (longdesc) values ('SMARTNET%^" 8X5XNBD') here is the actual snippet: PreparedStatement ps = conn.prepareStatement("INSERT INTO itemdescription (longdesc) values(?)"); ps.setString(1, itemdescription); ps.executeUpdate(); It will produce an error saying : Cannot insert the value NULL into column 'LongDesc', table 'App.dbo.itemdescription'; column does not allow nulls. Insert fails I have tried urlencode/urldecode String encodedString = URLEncoder.encode(longdesc, "UTF-8"); String decitemdescription = URLDecoder.decode(itemdescription, "UTF-8"); and i've also tried these functions //BEGIN URL Encoder final static String[] hex = { "%00", "%01", "%02", "%03", "%04", "%05", "%06", "%07", "%08", "%09", "%0a", "%0b", "%0c", "%0d", "%0e", "%0f", "%10", "%11", "%12", "%13", "%14", "%15", "%16", "%17", "%18", "%19", "%1a", "%1b", "%1c", "%1d", "%1e", "%1f", "%20", "%21", "%22", "%23", "%24", "%25", "%26", "%27", "%28", "%29", "%2a", "%2b", "%2c", "%2d", "%2e", "%2f", "%30", "%31", "%32", "%33", "%34", "%35", "%36", "%37", "%38", "%39", "%3a", "%3b", "%3c", "%3d", "%3e", "%3f", "%40", "%41", "%42", "%43", "%44", "%45", "%46", "%47", "%48", "%49", "%4a", "%4b", "%4c", "%4d", "%4e", "%4f", "%50", "%51", "%52", "%53", "%54", "%55", "%56", "%57", "%58", "%59", "%5a", "%5b", "%5c", "%5d", "%5e", "%5f", "%60", "%61", "%62", "%63", "%64", "%65", "%66", "%67", "%68", "%69", "%6a", "%6b", "%6c", "%6d", "%6e", "%6f", "%70", "%71", "%72", "%73", "%74", "%75", "%76", "%77", "%78", "%79", "%7a", "%7b", "%7c", "%7d", "%7e", "%7f", "%80", "%81", "%82", "%83", "%84", "%85", "%86", "%87", "%88", "%89", "%8a", "%8b", "%8c", "%8d", "%8e", "%8f", "%90", "%91", "%92", "%93", "%94", "%95", "%96", "%97", "%98", "%99", "%9a", "%9b", "%9c", "%9d", "%9e", "%9f", "%a0", "%a1", "%a2", "%a3", "%a4", "%a5", "%a6", "%a7", "%a8", "%a9", "%aa", "%ab", "%ac", "%ad", "%ae", "%af", "%b0", "%b1", "%b2", "%b3", "%b4", "%b5", "%b6", "%b7", "%b8", "%b9", "%ba", "%bb", "%bc", "%bd", "%be", "%bf", "%c0", "%c1", "%c2", "%c3", "%c4", "%c5", "%c6", "%c7", "%c8", "%c9", "%ca", "%cb", "%cc", "%cd", "%ce", "%cf", "%d0", "%d1", "%d2", "%d3", "%d4", "%d5", "%d6", "%d7", "%d8", "%d9", "%da", "%db", "%dc", "%dd", "%de", "%df", "%e0", "%e1", "%e2", "%e3", "%e4", "%e5", "%e6", "%e7", "%e8", "%e9", "%ea", "%eb", "%ec", "%ed", "%ee", "%ef", "%f0", "%f1", "%f2", "%f3", "%f4", "%f5", "%f6", "%f7", "%f8", "%f9", "%fa", "%fb", "%fc", "%fd", "%fe", "%ff" }; /** * Encode a string to the "x-www-form-urlencoded" form, enhanced * with the UTF-8-in-URL proposal. This is what happens: * * <ul> * <li><p>The ASCII characters 'a' through 'z', 'A' through 'Z', * and '0' through '9' remain the same. * * <li><p>The unreserved characters - _ . ! ~ * ' ( ) remain the same. * * <li><p>The space character ' ' is converted into a plus sign '+'. * * <li><p>All other ASCII characters are converted into the * 3-character string "%xy", where xy is * the two-digit hexadecimal representation of the character * code * * <li><p>All non-ASCII characters are encoded in two steps: first * to a sequence of 2 or 3 bytes, using the UTF-8 algorithm; * secondly each of these bytes is encoded as "%xx". * </ul> * * @param s The string to be encoded * @return The encoded string */ public static String encode(String s) { StringBuffer sbuf = new StringBuffer(); int len = s.length(); for (int i = 0; i < len; i++) { int ch = s.charAt(i); if ('A' <= ch && ch <= 'Z') { // 'A'..'Z' sbuf.append((char)ch); } else if ('a' <= ch && ch <= 'z') { // 'a'..'z' sbuf.append((char)ch); } else if ('0' <= ch && ch <= '9') { // '0'..'9' sbuf.append((char)ch); } else if (ch == ' ') { // space sbuf.append('+'); } else if (ch == '-' || ch == '_' // unreserved || ch == '.' || ch == '!' || ch == '~' || ch == '*' || ch == '\'' || ch == '(' || ch == ')') { sbuf.append((char)ch); } else if (ch <= 0x007f) { // other ASCII sbuf.append(hex[ch]); } else if (ch <= 0x07FF) { // non-ASCII <= 0x7FF sbuf.append(hex[0xc0 | (ch >> 6)]); sbuf.append(hex[0x80 | (ch & 0x3F)]); } else { // 0x7FF < ch <= 0xFFFF sbuf.append(hex[0xe0 | (ch >> 12)]); sbuf.append(hex[0x80 | ((ch >> 6) & 0x3F)]); sbuf.append(hex[0x80 | (ch & 0x3F)]); } } return sbuf.toString(); } //end encode and //decode url private static String unescape(String s) { StringBuffer sbuf = new StringBuffer () ; int l = s.length() ; int ch = -1 ; int b, sumb = 0; for (int i = 0, more = -1 ; i < l ; i++) { /* Get next byte b from URL segment s */ switch (ch = s.charAt(i)) { case '%': ch = s.charAt (++i) ; int hb = (Character.isDigit ((char) ch) ? ch - '0' : 10+Character.toLowerCase((char) ch) - 'a') & 0xF ; ch = s.charAt (++i) ; int lb = (Character.isDigit ((char) ch) ? ch - '0' : 10+Character.toLowerCase ((char) ch)-'a') & 0xF ; b = (hb << 4) | lb ; break ; case '+': b = ' ' ; break ; default: b = ch ; } /* Decode byte b as UTF-8, sumb collects incomplete chars */ if ((b & 0xc0) == 0x80) { // 10xxxxxx (continuation byte) sumb = (sumb << 6) | (b & 0x3f) ; // Add 6 bits to sumb if (--more == 0) sbuf.append((char) sumb) ; // Add char to sbuf } else if ((b & 0x80) == 0x00) { // 0xxxxxxx (yields 7 bits) sbuf.append((char) b) ; // Store in sbuf } else if ((b & 0xe0) == 0xc0) { // 110xxxxx (yields 5 bits) sumb = b & 0x1f; more = 1; // Expect 1 more byte } else if ((b & 0xf0) == 0xe0) { // 1110xxxx (yields 4 bits) sumb = b & 0x0f; more = 2; // Expect 2 more bytes } else if ((b & 0xf8) == 0xf0) { // 11110xxx (yields 3 bits) sumb = b & 0x07; more = 3; // Expect 3 more bytes } else if ((b & 0xfc) == 0xf8) { // 111110xx (yields 2 bits) sumb = b & 0x03; more = 4; // Expect 4 more bytes } else /*if ((b & 0xfe) == 0xfc)*/ { // 1111110x (yields 1 bit) sumb = b & 0x01; more = 5; // Expect 5 more bytes } /* We don't test if the UTF-8 encoding is well-formed */ } return sbuf.toString() ; } but the decoding doesn't change it back to the original special characters. Any ideas? thanks in advance UPDATE: I tried adding these two statements to grab the request String itemdescription = URLDecoder.decode(request.getParameter("itemdescription"), "UTF-8"); String itemshortdescription = URLDecoder.decode(request.getParameter("itemshortdescription"), "UTF-8"); System.out.println("processRequest | short descrip "); and this is failing as well if that helps. UPDATE2: I created an html form and did a direct insert with the encoded itemdescription such as and the insertion works correctly with the special charaters and everything. I guess there is something going on with my javascript submit. Any ideas on this?

  Read the article

< Previous Page | 7 8 9 10 11