Search Results

Search found 599 results on 24 pages for 'rx'.

Page 11/24 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• Intel I217LM ethernet controller not detected by Ubuntu 12.04LTS

  - by Alexandr Kurilin

  My last installation of Ubuntu 12.04 on a machine using an ASUS Q87M-E motherboard with an Intel I217LM Ethernet controller has failed to detect the ethernet card. The only thing displayed by ifconfig -a is the loopback. I double-checked in the BIOS, and the controller should be online. $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lspci 00:00.0 Host bridge: Intel Corporation Haswell DRAM Controller (rev 06) 00:01.0 PCI bridge: Intel Corporation Haswell PCI Express x16 Controller (rev 06) 00:02.0 VGA compatible controller: Intel Corporation Haswell Integrated Graphics Controller (rev 06) 00:03.0 Audio device: Intel Corporation Haswell HD Audio Controller (rev 06) 00:14.0 USB controller: Intel Corporation Lynx Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Lynx Point MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation Lynx Point KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 153a (rev 04) 00:1a.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Lynx Point HD Audio Controller (rev 04) 00:1d.0 USB controller: Intel Corporation Lynx Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Lynx Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Lynx Point 6-Port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation Lynx Point SMBus Controller (rev 04) $ lsmod Module Size Used by vesafb 13844 1 snd_hda_codec_realtek 224173 1 arc4 12529 2 joydev 17693 0 usbhid 47238 0 hid 99636 1 usbhid rfcomm 47604 0 rt73usb 31735 0 crc_itu_t 12707 1 rt73usb rt2x00usb 20808 1 rt73usb rt2x00lib 55326 2 rt73usb,rt2x00usb mac80211 506862 2 rt2x00usb,rt2x00lib cfg80211 205774 2 rt2x00lib,mac80211 eeepc_wmi 13109 0 bnep 18281 2 asus_wmi 24456 1 eeepc_wmi sparse_keymap 13890 1 asus_wmi psmouse 97485 0 bluetooth 180153 10 rfcomm,bnep ppdev 17113 0 snd_hda_intel 33719 6 snd_hda_codec 127706 2 snd_hda_codec_realtek,snd_hda_intel snd_seq_midi 13324 0 snd_hwdep 17764 1 snd_hda_codec snd_rawmidi 30748 1 snd_seq_midi serio_raw 13211 0 snd_pcm 97275 2 snd_hda_intel,snd_hda_codec snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61929 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq parport_pc 32866 1 snd 79041 21 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_rawmidi,snd_pcm,snd_seq,snd_timer,snd_seq_device video 19651 0 soundcore 15091 1 snd wmi 19256 1 asus_wmi snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp $ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1091 errors:0 dropped:0 overruns:0 frame:0 TX packets:1091 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:80048 (80.0 KB) TX bytes:80048 (80.0 KB) wlan0 Link encap:Ethernet HWaddr 00:fd:07:91:a8:b9 inet addr:172.16.42.4 Bcast:172.16.42.255 Mask:255.255.255.0 inet6 addr: fe80::2fd:7ff:fe91:a8b9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:56644 errors:0 dropped:0 overruns:0 frame:0 TX packets:36417 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:85270918 (85.2 MB) TX bytes:3413849 (3.4 MB) additionally, running sudo lshw -C network returns: *-network UNCLAIMED description: Ethernet Controller [...] I'm pretty stumped at this point. This doesn't sound like a very uncommon ethernet controller and I figured it would be picked up by the system. Does anybody have advice for how to deal with this? Anything specific I should look into to figure out what could be causing this? Edit: It seems that following the guide on the Intel e1000e drivers page allowed the card to start working. Is this a real fix or is there a better way?

  Read the article

• Slow wired internet connection on Realtek RTL8168-8111 (Rev 6)

  - by Mark

  I keep on seeing issues people are having with their wireless. I am having an issue with being wired into my router. I installed Ubuntu 11.10 the other day, on my custom PC. The motherboard I have installed on this PC is an ASUS P8H61-M. The issue I am having is with my speed. I have a dual boot, windows 7 and the new Ubuntu. On my Windows install I am getting test speeds from Speakeasy at 17Mbps and actual downloads around 2-3MB/s. With Ubuntu, I am getting test speeds from Speakeasy at 1.14Mbps and actual downloads around 60KB/s. I have disabled IPv6 and am no using GoogleDNS for my DNS, but it hasn't resolved the issue. I have scanned my router (WRT54GS Linksys) to disable IPv6 connections, and I am not seeing any option for that. I cannot figure out why I am getting such sluggish internet connection. Any help to resolve would be great! I performed an iconfig -a with these results: mark@Mark-ASUS:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr f4:6d:04:d1:2c:4e inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f66d:4ff:fed1:2c4e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:21888 errors:0 dropped:21888 overruns:0 frame:21888 TX packets:21068 errors:0 dropped:90 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:26348337 (26.3 MB) TX bytes:2217140 (2.2 MB) Interrupt:46 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:952 (952.0 B) TX bytes:952 (952.0 B) My specs are: mark@Mark-ASUS:~$ sudo lspci -nn 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) 06:00.0 PCI bridge [0604]: ASMedia Technology Inc. Device [1b21:1080] (rev 01) udev information: KERNEL[11.351405] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 UDEV [11.363905] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 ID_VENDOR_FROM_DATABASE=Realtek Semiconductor Co., Ltd. ID_MODEL_FROM_DATABASE=RTL8111/8168B PCI Express Gigabit Ethernet controller ID_BUS=pci ID_VENDOR_ID=0x10ec ID_MODEL_ID=0x8168 ID_MM_CANDIDATE=1 dmesg information: [ 2.855982] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.856366] r8169 0000:04:00.0: eth0: RTL8168b/8111b at 0xffffc9000064c000, f4:6d:04:d1:2c:4e, XID 0c900800 IRQ 46 [ 12.540956] r8169 0000:04:00.0: eth0: link down [ 12.540961] r8169 0000:04:00.0: eth0: link down [ 12.541173] ADDRCONF(NETDEV_UP): eth0: link is not ready I took out a lot of information that did not pertain to eth0, because the previous edits wouldn't save. If I need any more information, let me know. I would love to get this resolved. The other issue I am noticing is sometimes my connection disconnects all together, for about a minute, then it reconnects.

  Read the article

• Schizophrenic Ubuntu 12.10-12.04: Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to getit to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe

  Read the article

• Access denied error while mounting a shared folder?

  - by SSH

  I am a linux newbie and I have a very basic question. I have three machines - machineA 10.108.24.132 machineB 10.108.24.133 machineC 10.108.24.134 and all those machines have Ubuntu 12.04 installed in it and I have root access to all those three machines. Now I am supposed to do below things in my above machines - Create mount point /opt/exhibitor/conf Mount the directory in all servers. sudo mount <NFS-SERVER>:/opt/exhibitor/conf /opt/exhibitor/conf/ I have already created /opt/exhibitor/conf directory in all those three machines as mentioned above. Now I am trying to create a Mount Point on all those three machines. So I followed the below process - Install NFS support files and NFS kernel server in all the above three machines $ sudo apt-get install nfs-common nfs-kernel-server Create the shared directory in all the above three machines $ mkdir /opt/exhibitor/conf/ Edited the /etc/exports and added the entry like this in all the above three machines - # /etc/exports: the access control list for filesystems which may be exported # to NFS clients. See exports(5). # # Example for NFSv2 and NFSv3: # /srv/homes hostname1(rw,sync,no_subtree_check) hostname2(ro,sync,no_subtree_check) # # Example for NFSv4: # /srv/nfs4 gss/krb5i(rw,sync,fsid=0,crossmnt,no_subtree_check) # /srv/nfs4/homes gss/krb5i(rw,sync,no_subtree_check) # /opt/exhibitor/conf/ 10.108.24.*(rw) Run exportfs in all the above three machines root@machineA:/# exportfs -rv exportfs: /etc/exports [1]: Neither 'subtree_check' or 'no_subtree_check' specified for export "10.108.24.*:/opt/exhibitor/conf/". Assuming default behaviour ('no_subtree_check'). NOTE: this default has changed since nfs-utils version 1.0.x exporting 10.108.24.*:/opt/exhibitor/conf Now I did showmount on machineA root@machineA:/# showmount -e 10.108.24.132 Export list for 10.108.24.132: /opt/exhibitor/conf 10.108.24.* And also I have started the NFS server like this in all the above three machines - sudo /etc/init.d/nfs-kernel-server start And now when I did this, I am getting an error - root@machineA:/# sudo mount -t nfs 10.108.24.132:/opt/exhibitor/conf /opt/exhibitor/conf/ mount.nfs: access denied by server while mounting 10.108.24.132:/opt/exhibitor/conf I have also tried doing the same thing from machineB and machineC as well and still I get the same error- root@machineB:/# sudo mount -t nfs 10.108.24.132:/opt/exhibitor/conf /opt/exhibitor/conf/ root@machineC:/# sudo mount -t nfs 10.108.24.132:/opt/exhibitor/conf /opt/exhibitor/conf/ Did my /etc/exports file looks good? As I have the same content in all the three machines. And also are there any logs related to NFS which I can see to find any clues? Any idea what wrong I am doing here? UPDATE:- So my etc/exports files would be like this in all the three machines - # /etc/exports: the access control list for filesystems which may be exported # to NFS clients. See exports(5). # # Example for NFSv2 and NFSv3: # /srv/homes hostname1(rw,sync,no_subtree_check) hostname2(ro,sync,no_subtree_check) # # Example for NFSv4: # /srv/nfs4 gss/krb5i(rw,sync,fsid=0,crossmnt,no_subtree_check) # /srv/nfs4/homes gss/krb5i(rw,sync,no_subtree_check) # /opt/exhibitor/conf/ 10.108.24.132(rw) /opt/exhibitor/conf/ 10.108.24.133(rw) /opt/exhibitor/conf/ 10.108.24.134(rw) Just a quick check - The IP Address that I am taking for each machine as mentioned above is like this - root@machineB:/# ifconfig eth0 Link encap:Ethernet HWaddr 00:50:56:ad:5b:a7 inet addr:10.108.24.133 Bcast:10.108.27.255 Mask:255.255.252.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5696812 errors:0 dropped:12462 overruns:0 frame:0 TX packets:5083427 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7904369145 (7.9 GB) TX bytes:601844910 (601.8 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:187144 errors:0 dropped:0 overruns:0 frame:0 TX packets:187144 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:24012302 (24.0 MB) TX bytes:24012302 (24.0 MB) Here the IP Address that I am taking for machineB is 10.108.24.133.

  Read the article

• How do I get to work my Atheros AR9485 Wireless card in Ubuntu 14.04 LTS?

  - by Ivan Kreimer

  I've recently installed Ubuntu 14.04 LTS in my ASUS D550CA, and so far things have gone great. The only problem I've got is the Wi-Fi. It doesn't work. I've got an Qualcomm Atheros AR9485. I've tried installing the drivers, but the sytem says it doesn't find any. So I started looking around this forum for solutions. I've read every single post from this forum about my Wi-Fi network adapter, and I've found nothing that solves my problem. Let me give you some info about my configuration. Disclaimer: my configuration is in spanish, so if you don't understand something you can either use Google translate, or use your imagination. :D When I run $ sudo lshw -C network this is what I get: *-network DEACTIVATED descripción: Interfaz inalámbrica producto: AR9485 Wireless Network Adapter fabricante: Qualcomm Atheros id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: wlan0 versión: 01 serie: 28:e3:47:5c:5d:3f anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.13.0-34-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:f7d00000-f7d7ffff memoria:f7d80000-f7d8ffff *-network descripción: Ethernet interface producto: RTL8101E/RTL8102E PCI Express Fast Ethernet controller fabricante: Realtek Semiconductor Co., Ltd. id físico: 0.2 información del bus: pci@0000:03:00.2 nombre lógico: eth0 versión: 06 serie: e0:3f:49:ce:57:49 tamaño: 100Mbit/s capacidad: 100Mbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8402-1_0.0.1 10/26/11 ip=181.165.245.39 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s recursos: irq:41 ioport:e000(size=256) memoria:f0004000-f0004fff memoria:f0000000-f0003fff At the beginning, you'll see that it says "*-network DEACTIVATED" (or at least that's what I translated), is that something bad? Then, when I run ipconfig this is what I get: eth0 Link encap:Ethernet direcciónHW e0:3f:49:ce:57:49 Direc. inet:181.165.245.39 Difus.:181.165.245.255 Másc:255.255.255.0 Dirección inet6: fe80::e23f:49ff:fece:5749/64 Alcance:Enlace ACTIVO DIFUSIÓN FUNCIONANDO MULTICAST MTU:1500 Métrica:1 Paquetes RX:221199 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:62025 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:124409589 (124.4 MB) TX bytes:7471899 (7.4 MB) lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:65536 Métrica:1 Paquetes RX:2977 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:2977 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:397158 (397.1 KB) TX bytes:397158 (397.1 KB) When I put iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Finally, when I put sudo rfkill list all, I got: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no I hope anyone can help me solve this, I've searched a lot and found no solution. Thanks a lot.

  Read the article

• Sqlite3 "chained" query

  - by Arrieta

  I need to create a configuration file from a data file that looks as follows: MAN1_TIME '01-JAN-2010 00:00:00.0000 UTC' MAN1_RX 123.45 MAN1_RY 123.45 MAN1_RZ 123.45 MAN1_NEXT 'MAN2' MAN2_TIME '01-MAR-2010 00:00:00.0000 UTC' MAN2_RX 123.45 [...] MAN2_NEXT 'MANX' [...] MANX_TIME [...] This file describes different "legs" of a trajectory. In this case, MAN1 is chained to MAN2, and MAN2 to MANX. In the original file, the chains are not as obvious (i.e., they are non-sequential). I've managed to read the file and store in an Sqlite3 database (I'm using the Python interface). The table is stored with three columns: Id, Par, and Val; for instance, Id='MAN1', Par='RX', and Val='123.45'. I'm interested in querying such database for obtaining the information related to 'n' legs. In English, that would be: "Select RX,RY,RZ for the next five legs starting on MAN1" So the query would go to MAN1, retrieve RX, RY, RZ, then read the parameter NEXT and go to that Id, retrieve RX, RY, RZ; read the parameter NEXT; go to that one ... like this five times. How can I pass such query with "dynamic parameters"? Thank you.

  Read the article

• CodePlex Daily Summary for Sunday, May 02, 2010

  CodePlex Daily Summary for Sunday, May 02, 2010New ProjectsAdventureWorks in Access: AdventureWorks database in Access format. Data has been ported in Access starting from Adventure Works database for SQL Server 2008.amplifi: This project is still under construction. We will add more information here as soon as it is available.ASP.NET MVC Bug Tracker: Bug Track written in C# ASP.NET MVC 2BigDecimal: BigDecimal is an attempt to create a number class that can have large precision. It is developed in vb.net (.net 4).CBM-Command: Coming soon....Chuyou: ChuyouCMinus: A C Minus Compiler!Complex and advanced mathematical functions: Mathematics toolkit is a Class Library Project which help Programmers to Calculate Mathematics Functions easily.Confuser: Confuser is a obfuscator for .NET. It is developed in C# and using Mono.Cecil for assembly manipulation.easypos: Micro punto de venta que permite ventas express de ropa, que se acopla fácil y transaparente con el ERP Click OneElmech Address Book: Web based Address Book for maintaining details of your business clients. This project targets Suppliers - Traders - Manufacturers - users. Applicat...Feed Viewer: Feed Viewer is able to synchronize subscribed feed and red news among all computers you are using. It understands both RSS and Atom format. It can ...Google URL Shortener, C#: Implementation in C# of generating short URLs by Goo.gl service (Google URL Shortener)MARS - Medical Assistant Record System: MARS - Medical Assistant Record SystemRx Contrib: Rx Contrib is a library which contain extensions for the Rx frameworkSimple Service Administration Tool: A simple tool to start/stop/restart a service of a WinNT based system. The tool is placed in the task bar as a notify icon, so the specified servic...Vis3D: Visual 3D controls for Silverlight.VisContent: XML content controls for ASP.NET.Windows Phone 7 database: This project implements a Isolated Storage (IsolatedStorage) based database for Windows Phone 7. The database consists of table object, each one s...New Releases$log$ / Keyword Substitution / Expansion Check-In Policy (TFS - LogSubstPol): LogSubstPol_v1.2010.0.4 (VS2010): LogSubstPol is a TFS check-in policy which insertes the check-in comments and other keywords into your source code, so you can keep track of the ch...Bojinx: Bojinx Core V4.5.1: The following new features were added: You can now use either BojinxMXMLContext or ContextModule to configure your application or module context. ...CBM-Command: Initial Public Demonstration: Initial public demonstration version. Can browse attached drives and display directory of any attached drive. A common question is "How does it w...Confuser: Confuser v1.0: It is the Confuser v1.0 that used to confuse the reverse-engineers :)Font Family Name Retrieval: 2nd Release: Added New MKV Font Extractor application to showcase the library. MKV Font Extractor depends on MKVToolnix to be installed before it will work. R...Google URL Shortener, C#: Goo.gl-CS v1 Beta: Extract the ZIP file to any location. Two files have to be in the same folder!HouseFly controls: HouseFly controls alpha 0.9.6.1: HouseFly controls release 0.9.6.1 alphaIsWiX: IsWiX 1.0.261.0: Build 1.0.261.0 - built against Fireworks 1.0.264.0. Adds support for VS2010 Integration to support WiX 3.5 beta releases.Managed Extensibility Framework (MEF) Contrib: MefContrib 0.9.2.0: Added conventions based catalog (read more at http://www.thecodejunkie.com/2010/03/bringing-convention-based-registration.html) MEF + Unity integ...MARS - Medical Assistant Record System: license: licenseNSIS Autorun: NSIS Autorun 0.1.5: This release includes source code, executable binary, files and example materials.PHP.net: Release 0.0.0.1: This is the first release of PHP.Net. The features available in this release are: new File Save File Save As Open File In the rar file is th...Rx Contrib: V1: Rx Contrib is ongoing effort for community additions for Rx. Current features are: ReactiveQueue: ISubject that does not loose values if there are ...Silverlight 4.0 Popup Menu: Context Menu for Silverlight 4 v1.0: - Added a margin for icon display. - Added the PopupMenuItem class which is a derivative of the DockPanel. - Find* methods can now drill down the v...Silverlight 4.0 Popup Menu: Context Menu for Silverlight 4 v1.1 Beta: - Added a margin for icon display. - Added the PopupMenuItem class which is a derivative of the DockPanel. - Added a AddSeperator method. - The Fin...Simple Service Administration Tool: SSATool 0.1.3: New Simple Service Administration Tool Version 0.1.3 compiled with Visual Studio .NET 2010.sMAPedit: sMAPedit v0.7a + Map-Pack: Required Additional Map-Pack Added: height setting by color picker (shift+leftclick)sMAPedit: sMAPedit v0.7b: Fixed: force a gargabe collection update to prevent pictureBox's memory leaksqwarea: Sqwarea 0.0.228.0 (alpha): This release corrects a critical bug in ConnexityNotifier service. We strongly recommend you to upgrade to this version. Known bugs : if you open...StackOverflow Desktop Client in C# and WPF: StackOverflow Client 0.1: Source code for the sample.TortoiseHg: TortoiseHg 1.0.2: This is a bug fix release, we recommend all users upgrade to 1.0.2VCC: Latest build, v2.1.30501.0: Automatic drop of latest buildVidCoder: 0.4.0: Changes: Added ability to queue up multiple video files or titles at once. These queued jobs will use the currently selected encoding settings. Mul...WabbitStudio Z80 Software Tools: Wabbitemu 32-bit Test Release: Wabbitemu Visual Studio build for testing purposesWindows Phone 7 database: Initial Release v1.0: This project implements a Isolated Storage (IsolatedStorage) based database for Windows Phone 7. The usage of this software is very simple. You cre...YouTubeEmbeddedVideo WebControl for ASP.NET: VideoControls version 1: This zip file contains the VideoControls.dll, version 1.Most Popular ProjectsRawrWBFS ManagerAJAX Control Toolkitpatterns & practices – Enterprise LibraryMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)iTuner - The iTunes CompanionASP.NETDotNetNuke® Community EditionMost Active Projectspatterns & practices – Enterprise LibraryRawrIonics Isapi Rewrite FilterHydroServer - CUAHSI Hydrologic Information System Serverpatterns & practices: Azure Security GuidanceTinyProjectNB_Store - Free DotNetNuke Ecommerce Catalog ModuleBlogEngine.NETDambach Linear Algebra FrameworkFacebook Developer Toolkit

  Read the article

• Wireless Connected But No Internet Connection (Ubuntu 12.04)

  - by Zxy

  I am using same network for 2 days and everything was normal. However, today even though it shows me as connected to the network, I do not have internet connection. If I use ethernet cable instead of wireless, I am still able to connect to the internet. Also my friends are able to connect to the wireless network and they can get internet connection. I did not update or install anything since yesterday. Therefore I do not have any idea why it is happening. Here is some information about my connection: I will be appreciate to any kind of help. root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 root@ghostrider:/etc/resolvconf# ping 127.0.0.1 PING 127.0.0.1 (127.0.0.1) 56(84) bytes of data. 64 bytes from 127.0.0.1: icmp_req=1 ttl=64 time=0.042 ms 64 bytes from 127.0.0.1: icmp_req=2 ttl=64 time=0.023 ms 64 bytes from 127.0.0.1: icmp_req=3 ttl=64 time=0.036 ms 64 bytes from 127.0.0.1: icmp_req=4 ttl=64 time=0.040 ms ^C --- 127.0.0.1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 2998ms rtt min/avg/max/mdev = 0.023/0.035/0.042/0.008 ms root@ghostrider:/etc/resolvconf# ping 192.168.1.3 PING 192.168.1.3 (192.168.1.3) 56(84) bytes of data. ^C --- 192.168.1.3 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18143ms root@ghostrider:/etc/resolvconf# ping 8.8.8.8 PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data. ^C --- 8.8.8.8 ping statistics --- 11 packets transmitted, 0 received, 100% packet loss, time 10079ms root@ghostrider:/etc/resolvconf# cat /etc/lsb-release; uname -a DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04 LTS" Linux ghostrider 3.2.0-24-generic-pae #39-Ubuntu SMP Mon May 21 18:54:21 UTC 2012 i686 i686 i386 GNU/Linux root@ghostrider:/etc/resolvconf# lspci -nnk | grep -iA2 net 03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0) Subsystem: Lenovo Device [17aa:3956] Kernel driver in use: atl1c -- 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Subsystem: Broadcom Corporation Device [14e4:0510] Kernel driver in use: wl root@ghostrider:/etc/resolvconf# lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 007: ID 0489:e00d Foxconn / Hon Hai Bus 001 Device 004: ID 1c7a:0801 LighTuning Technology Inc. Fingerprint Reader Bus 001 Device 005: ID 064e:f219 Suyin Corp. Bus 002 Device 010: ID 0424:2412 Standard Microsystems Corp. Bus 002 Device 004: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 011: ID 0403:6010 Future Technology Devices International, Ltd FT2232C Dual USB-UART/FIFO IC root@ghostrider:/etc/resolvconf# iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz Access Point: 00:16:E3:40:C3:E4 Bit Rate=54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=-52 dBm Noise level=-97 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. root@ghostrider:/etc/resolvconf# rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 5: hci0: Bluetooth Soft blocked: no Hard blocked: no root@ghostrider:/etc/resolvconf# lsmod Module Size Used by nls_iso8859_1 12617 0 nls_cp437 12751 0 vfat 17308 0 fat 55605 1 vfat usb_storage 39646 0 uas 17828 0 snd_hda_codec_realtek 174055 1 rfcomm 38139 12 parport_pc 32114 0 ppdev 12849 0 bnep 17830 2 joydev 17393 0 ftdi_sio 35859 1 usbserial 37173 3 ftdi_sio snd_hda_intel 32765 3 snd_hda_codec 109562 2 snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec acer_wmi 23612 0 hid_logitech_dj 18177 0 snd_pcm 80845 2 snd_hda_intel,snd_hda_codec uvcvideo 67203 0 btusb 17912 2 snd_seq_midi 13132 0 videodev 86588 1 uvcvideo bluetooth 158438 23 rfcomm,bnep,btusb psmouse 72919 0 usbhid 41906 1 hid_logitech_dj snd_rawmidi 25424 1 snd_seq_midi intel_ips 17753 0 serio_raw 13027 0 hid 77367 2 hid_logitech_dj,usbhid ideapad_laptop 17890 0 sparse_keymap 13658 2 acer_wmi,ideapad_laptop lib80211_crypt_tkip 17275 0 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event wl 2646601 0 wmi 18744 1 acer_wmi i915 414672 3 drm_kms_helper 45466 1 i915 snd_timer 28931 2 snd_pcm,snd_seq mac_hid 13077 0 snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq lib80211 14040 2 lib80211_crypt_tkip,wl drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 snd 62064 15 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_se q,snd_timer,snd_seq_device video 19068 1 i915 mei 36570 0 soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp atl1c 36718 0 root@ghostrider:/etc/resolvconf# nm-tool NetworkManager Tool State: connected (global) - Device: eth1 [PoliTekno] ---------------------------------------------------- Type: 802.11 WiFi Driver: wl State: connected Default: yes HW Address: AC:81:12:7F:6B:B2 Capabilities: Speed: 54 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) CnDStudios: Infra, 00:12:BF:3F:0A:8A, Freq 2412 MHz, Rate 54 Mb/s, Strength 85 WPA AIR_TIES: Infra, 00:1C:A8:6E:84:32, Freq 2462 MHz, Rate 54 Mb/s, Strength 72 WPA2 VKSS: Infra, 00:E0:4D:01:0D:47, Freq 2452 MHz, Rate 54 Mb/s, Strength 62 WPA2 PROGEDA: Infra, 00:1A:2A:60:BF:61, Freq 2462 MHz, Rate 54 Mb/s, Strength 47 WPA MobilAtolye: Infra, 72:2B:C1:65:75:3C, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 AIRTIES_WAR-141: Infra, 00:1C:A8:AB:AA:48, Freq 2422 MHz, Rate 54 Mb/s, Strength 35 WPA WPA2 tilda_biri_yeni: Infra, 54:E6:FC:B0:3C:E9, Freq 2437 MHz, Rate 0 Mb/s, Strength 34 WEP *PoliTekno: Infra, 00:16:E3:40:C3:E4, Freq 2462 MHz, Rate 54 Mb/s, Strength 100 WPA2 AIRTIES_RJY: Infra, 00:1A:2A:BD:85:16, Freq 2462 MHz, Rate 54 Mb/s, Strength 55 WEP IPv4 Settings: Address: 0.0.0.0 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: F0:DE:F1:6C:90:65 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off root@ghostrider:/etc/resolvconf# sudo iwlist scan lo Interface doesn't support scanning. eth1 Scan completed : Cell 01 - Address: 00:16:E3:40:C3:E4 ESSID:"PoliTekno" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-48 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: 00:E0:4D:01:0D:47 ESSID:"VKSS" Mode:Managed Frequency:2.452 GHz (Channel 9) Quality:4/5 Signal level:-64 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s Cell 03 - Address: 00:1C:A8:AB:AA:48 ESSID:"AIRTIES_WAR-141" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-77 dBm Noise level:-95 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DDB20050F204104A0001101049001E007FC5100018DE7CF0D8B70223A62711C18926AC290E30303030303139631044000102103B0001031047001076B31BC241E953CB99C3872554425A28102100194169725469657320576972656C657373204E6574776F726B73102300074169723534343010240008312E322E302E31321042000F4154303939313131383030323832351054000800060050F20400011011000741697235343430100800020084103C000103 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 04 - Address: 72:2B:C1:65:75:3C ESSID:"MobilAtolye" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:2/5 Signal level:-78 dBm Noise level:-92 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK IE: Unknown: DDA20050F204104A0001101044000102103B00010310470010BC329E001DD811B28601722BC165753C1021001D48756177656920546563686E6F6C6F6769657320436F2E2C204C74642E1023001C48756177656920576972656C6573732041636365737320506F696E74102400065254323836301042000831323334353637381054000800060050F204000110110009487561776569415053100800020084103C000100 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s 18 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 12 Mb/s 24 Mb/s; 48 Mb/s Cell 05 - Address: 00:12:BF:3F:0A:8A ESSID:"CnDStudios" Mode:Managed Frequency:2.412 GHz (Channel 1) Quality:5/5 Signal level:-47 dBm Noise level:-95 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 06 - Address: 00:1C:A8:6E:84:32 ESSID:"AIR_TIES" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:5/5 Signal level:-56 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s Cell 07 - Address: 54:E6:FC:B0:3C:E9 ESSID:"tilda_biri_yeni" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-85 dBm Noise level:-99 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s 48 Mb/s; 54 Mb/s Cell 08 - Address: 18:28:61:16:57:C3 ESSID:"obilet" Mode:Managed Frequency:2.437 GHz (Channel 6) Quality:1/5 Signal level:-88 dBm Noise level:-99 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 09 - Address: 00:1A:2A:60:BF:61 ESSID:"PROGEDA" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-75 dBm Noise level:-98 dBm IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (1) : TKIP Authentication Suites (1) : PSK Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 22 Mb/s 6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s 36 Mb/s; 48 Mb/s; 54 Mb/s eth0 Interface doesn't support scanning.

  Read the article

• Errors when switching to specific static IP

  - by michaelc

  I had a Fedora box running using my static IP 69.169.136.6, etc, all configured according to what the ISP required. Just recently the hard drive failed (and I should have been keeping better backups) - while it is being recovered I would like to put up a webpage on my Archlinux PC explaining the problem - I presently do not have sufficient access to change the DNS record assigned to the domain. When I change my ip address while my system is running to 69.169.136.6, ifconfig reports the new ip address, but http://whatismyip.com/ does not. When I change it and reboot, I can't ping - the message I recieve is "connect: Network is unreachable" (when given one of google.com 's IP addresses - hostnames give me ping: unknown host xxx). Until I have access to the DNS system, what can I do to make this work? Edit: With new IP address, same problem, IP is now 69.169.136.29. Some commands might be useful: #ping 69.169.136.1 PING 69.169.136.1 (69.169.136.1) 56(84) bytes of data. 64 bytes from 69.169.136.1: icmp_seq=1 ttl=64 time=0.377 ms #ping 69.169.190.211 connect: Network is unreachable #ping 208.72.160.67 connect: Network is unreachable #ifconfig eth0 Link encap:Ethernet HWaddr 00:E0:4D:97:23:9B inet addr:69.169.136.29 Bcast:69.169.137.255 Mask:255.255.254.0 inet6 addr: fe80::2e0:4dff:fe97:239b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:132091 errors:0 dropped:0 overruns:0 frame:0 TX packets:17 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9635179 (9.1 Mb) TX bytes:1322 (1.2 Kb) Interrupt:29 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:48 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2480 (2.4 Kb) TX bytes:2480 (2.4 Kb) #ip route 69.169.136.0/23 dev eth0 proto kernel scope link src 69.169.136.29 #cat /etc/resolv.conf # Generated by dhcpcd #nameserver 208.67.222.222 #nameserver 208.67.220.220 nameserver 69.169.190.211 nameserver 208.72.160.67 # /etc/resolv.conf.tail can replace this line Update: have new static IP addresses, verified to work in Windows... Relevant portions of /etc/rc.conf below: #Static IP example #eth0="eth0 69.169.136.6 netmask 255.255.254.0 broadcast 69.169.136.1" #eth0="eth0 69.169.136.29 netmask 255.255.254.0 broadcast 69.169.137.255" eth0="eth0 69.169.136.32 netmask 255.255.254.0 broadcast 69.169.137.255" #eth0="dhcp" INTERFACES=(eth0) # Routes to start at boot-up (in this order) # Declare each route then list in ROUTES # - prefix an entry in ROUTES with a ! to disable it # #gateway="default gw 192.168.0.1" gateway="default gw 69.169.136.1" #gateway="69.169.136.1" ROUTES=(!gateway) #ROUTES=()

  Read the article

• eth0:0 is configured but not listed in ifconfig output

  - by FractalizeR

  Hello. I have the following problem: My server was given two IPs from [b]different[/b] subnets. Now I am trying to configure the system to work properly. I have created [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.69.241 NETMASK=255.255.254.0 NETWORK=79.174.68.0 ONBOOT=yes GATEWAY=79.174.68.1 TYPE=Ethernet [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0:0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.71.74 NETMASK=255.255.255.0 NETWORK=79.174.71.1 ONBOOT=yes GATEWAY=79.174.71.1 TYPE=Ethernet But both after "service network restart" and after "reboot" [root@server ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E inet addr:79.174.71.74 Bcast:79.174.71.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:feda:b10e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:910284 errors:0 dropped:0 overruns:0 frame:0 TX packets:2924 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:257964879 (246.0 MiB) TX bytes:232450 (227.0 KiB) Memory:df220000-df240000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:27 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6976 (6.8 KiB) TX bytes:6976 (6.8 KiB) Device eth0:0 is not shown as active. If I try [root@server ~]# ifconfig eth0:0 eth0:0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:df220000-df240000 It is shown as up and running, but IP is not assigned to it. Also it is strange, that IP address assigned to eth0:0 in config file is used by eth0. /var/log/messages shows nothing about network configuration errors on either eth0 or eth0:0. system-config-network seem to understand all settings correctly and resaves them ok also. "ifup eth0:0" executes ok, but ifconfig afterwards shows no eth0:0 device after that. What did I do wrong? May be the problem is that IPs are from different subnets?

  Read the article

• Cliq Wireless questions

  - by Nathan Adams

  Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

  Read the article

• VPN - force a selective range of ip to run on VPN (linux)

  - by Francesco

  Preface: I know there are similar question here and there however I'm a kind of newbie on Net stuff so I need an answer on this specific scenario, hoping that can help others too as it is a common problem Let say I cannot do anything on the local switch to change the local ip range, I don't want to use any complicate trick as use VMachine to hide the local ip range but I want to use net tools to solve the issue. Scenario my local net assign me an IP of this class 192.168.1.xxx (ex. 192.168.1.116) and my VPN (VPNC) assign me IP of same class 192.168.1.xxx (ex. 192.168.1.247) Obviously I need VPN to access local address (ex. 192.168.1.100) but when I open any address of the class 192.168.1.xx the route point to my local net and not to the VPN ones. I'm on linux and i'd like gui solution (network manager) in case it is not possible let play with route command. here what network manager offer me: Here my actual route once connected to the VPN: Here some route information (route -n) Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 182.71.21.106 192.168.1.1 255.255.255.255 UGH 0 0 0 wlan0 192.168.1.0 0.0.0.0 255.255.255.0 U 9 0 0 wlan0 192.168.1.246 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 Here my ifconfig : ppp0 Link encap:Point-to-Point Protocol inet addr:192.168.1.247 P-t-P:192.168.1.246 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:3415 errors:0 dropped:0 overruns:0 frame:0 TX packets:2525 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:3682328 (3.6 MB) TX bytes:402315 (402.3 KB) wlan0 Link encap:Ethernet HWaddr 4c:eb:42:06:a3:a6 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::4eeb:42ff:fe06:a3a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:72598 errors:0 dropped:0 overruns:0 frame:0 TX packets:42300 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76000532 (76.0 MB) TX bytes:13919400 (13.9 MB) The Question So basically I would like to add a rule to force this particular address (192.168.1.100) on the VPN and not on my local net

  Read the article

• Mysql server fails to start

  - by Nicolas Thery

  Googling since two hours, I require your assistance. I'm on a Debian virtual machine and I cloned it. The only change is the new IP adress it has. Mysql doesn't start any more: Starting MySQL database server: mysqld . . . . . . . . . . . . . . failed! There is no process called mysql. All the mysql log files in /var/log are empty. here is my.cnf file : [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp language = /usr/share/mysql/english skip-external-locking bind-address = 127.0.0.1 key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M general_log_file = /var/log/mysql/mysql.log log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M [mysqld_safe] syslog Here is the result of ifconfig : eth0 Link encap:Ethernet HWaddr 00:0c:29:12:98:9a inet adr:192.168.1.138 Bcast:192.168.1.255 Masque:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:754 errors:0 dropped:0 overruns:0 frame:0 TX packets:106 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:1000 RX bytes:101177 (98.8 KiB) TX bytes:17719 (17.3 KiB) lo Link encap:Boucle locale inet adr:127.0.0.1 Masque:255.0.0.0 adr inet6: ::1/128 Scope:Hôte UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 lg file transmission:0 RX bytes:560 (560.0 B) TX bytes:560 (560.0 B) As requested, here is the result of : sudo -u mysql mysqld, here is the result : root@debian:/home/nicolas/Bureau# sudo -u mysql mysqld 121004 14:26:57 [Note] Plugin 'FEDERATED' is disabled. mysqld: Can't find file: './mysql/plugin.frm' (errno: 13) 121004 14:26:57 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 121004 14:26:57 InnoDB: Initializing buffer pool, size = 8.0M 121004 14:26:57 InnoDB: Completed initialization of buffer pool 121004 14:26:57 InnoDB: Started; log sequence number 0 70822697 121004 14:26:57 [Note] Recovering after a crash using /var/log/mysql/mysql-bin 121004 14:26:57 [Note] Starting crash recovery... 121004 14:26:57 [Note] Crash recovery finished. 121004 14:26:57 [ERROR] mysqld: Can't find file: './mysql/host.frm' (errno: 13) 121004 14:26:57 [ERROR] Fatal error: Can't open and lock privilege tables: Can't find file: './mysql/host.frm' (errno: 13)

  Read the article

• Connecting to localhost resolves 127.0.0.1 but connects with external IP [Linux, Debian]

  - by skgsergio

  I'm having a problem with a dedicated server, I don't known if it's the default behavior but this is the problem: If I connect to a service located on the server with localhost the service gets as source IP the external IP. Let me show an example, I use netcat for listening on 127.0.0.1:4444 xxxxxx # nc -vv -l -s 127.0.0.1 -p 4444 listening on [127.0.0.1] 4444 ... Lets check if it's ok: xxxxxx ~ # netstat -atnp | grep 4444 tcp 0 0 127.0.0.1:4444 0.0.0.0:* LISTEN 14038/nc Ok lets connect: xxxxxx ~ # nc -vv 127.0.0.1 4444 localhost [127.0.0.1] 4444 (?) open Return to the tty that have the listening process and I get this: connect to [127.0.0.1] from xxxxxx.net [176.31.xxx.xx] 50354 So that's the problem. I have a server daemon that have to listen on localhost and checks that the ip is 127.0.0.1 when the client connects but for some reason when I connect to localhost it reports the external ip... If I do the same with IPv6 it works as excepted... Detects connection as localhost (::1). Some info that can be useful: "localhost" resolves without problems to 127.0.0.1 xxxxxx ~ # ping -c1 localhost PING localhost (127.0.0.1) 56(84) bytes of data. 64 bytes from localhost (127.0.0.1): icmp_req=1 ttl=64 time=0.086 ms Nothing weird on my hosts file, I think... xxxxxx ~ # grep -v ^# /etc/hosts 127.0.0.1 localhost localhost.localdomain 176.31.xxx.xx xxxxxx.net ns1.xxxxxx.net ::1 ip6-localhost ip6-loopback feo0::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts And ifconfig reports all ok... eth0 Link encap:Ethernet HWaddr e0:69:95:d8:30:a1 inet addr:176.31.xxx.xx Bcast:176.31.108.255 Mask:255.255.255.0 inet6 addr: 2001:41d0:8:xxxx::/64 Scope:Global inet6 addr: 2001:41d0:8:xxxx:x:xx:xx:xx/64 Scope:Global inet6 addr: fe80::e269:95ff:fed8:30a1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16916 errors:0 dropped:0 overruns:0 frame:0 TX packets:16914 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8410679 (8.0 MiB) TX bytes:10539881 (10.0 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:5570 errors:0 dropped:0 overruns:0 frame:0 TX packets:5570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:744490 (727.0 KiB) TX bytes:744490 (727.0 KiB)

  Read the article

• ubuntu eth0 not reconnecting after cable unplugged

  - by Alex

  I'm running kubuntu 9.10 w/ gnome, I have a static IP defined in /etc/network/interfaces When I unplugged my network cable and rebooted, then reconnected the network cable I was not able to connect. I tried using sudo ifup eth0, and then ifconfig and it seemed as though the IP address had been assigned and I was connected, but I wasn't. I then did ifdown eth0, and again ifup eth0. For some reason I'm not able to access the network. Furthermore, I also attempted to connect via wlan, and was able to connect to the wireless network, but cannot "see" the network. I can't transfer data or access the internet or anything on the network including the router. How do I resolve this? topsy@monolyth:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1c:25:1c:df:70 inet addr:192.168.1.145 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:25ff:fe1c:df70/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5720 errors:0 dropped:0 overruns:0 frame:0 TX packets:565 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:378035 (378.0 KB) TX bytes:46832 (46.8 KB) Memory:fe000000-fe020000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) By access the network I mean the local network as well as the internet. topsy@monolyth:~$ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=9.14 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.24 ms 64 bytes from 192.168.1.1: icmp_seq=3 ttl=64 time=1.01 ms 64 bytes from 192.168.1.1: icmp_seq=4 ttl=64 time=1.00 ms [snip... all OK, icmp_seq from 5-30, time between 0.981-1.25ms] ^C --- 192.168.1.1 ping statistics --- 30 packets transmitted, 30 received, 0% packet loss, time 29035ms rtt min/avg/max/mdev = 0.971/1.300/9.140/1.458 ms topsy@monolyth:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 root@monolyth:~# cat /etc/resolv.conf # Generated by NetworkManager

  Read the article

• OpenVPN not sending traffic to internet?

  - by coleifer

  I've set up openvpn on my pi and am running into a small issue. I can connect to the VPN server and ping it just fine, and I can also connect to other machines on my local network. However I am unable, when connected to the VPN, to reach the outside world (either by name lookup or IP). here are the details: On the server the tun0 interface: tun0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1500 inet 10.8.0.1 netmask 255.255.255.255 destination 10.8.0.2 unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 100 (UNSPEC) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 0 bytes 0 (0.0 B) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 I can ping it just fine: # ping -c 3 10.8.0.1 PING 10.8.0.1 (10.8.0.1) 56(84) bytes of data. 64 bytes from 10.8.0.1: icmp_seq=1 ttl=64 time=0.159 ms 64 bytes from 10.8.0.1: icmp_seq=2 ttl=64 time=0.155 ms 64 bytes from 10.8.0.1: icmp_seq=3 ttl=64 time=0.156 ms --- 10.8.0.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2002ms Routing table # ip route show default via 192.168.1.1 dev eth0 metric 204 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.6 metric 204 I also have ip traffic forwarding: net.ipv4.ip_forward = 1 I do not have any custom iptables rules (that I'm aware of). On the client, I can connect to the VPN. Here is my tun0: tun0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1500 inet 10.8.0.6 netmask 255.255.255.255 destination 10.8.0.5 unspec 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 txqueuelen 100 (UNSPEC) RX packets 0 bytes 0 (0.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 21 bytes 1527 (1.4 KiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 And on the client I can ping it: sudo ping -c 3 10.8.0.6 PING 10.8.0.6 (10.8.0.6) 56(84) bytes of data. 64 bytes from 10.8.0.6: icmp_seq=1 ttl=64 time=0.035 ms 64 bytes from 10.8.0.6: icmp_seq=2 ttl=64 time=0.026 ms 64 bytes from 10.8.0.6: icmp_seq=3 ttl=64 time=0.032 ms --- 10.8.0.6 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1998ms rtt min/avg/max/mdev = 0.026/0.031/0.035/0.003 ms I can ssh from the client into another server on my LAN (192.168.1.x), however I cannot reach anything outside my LAN. Here's some of the server logs at the bottom of this gist: https://gist.github.com/coleifer/6ef95c3008f130249933/edit I am frankly out of ideas! I don't think it's my client because both my laptop and my phone (which has an openvpn client) exhibit the same behavior. I had OpenVPN installed on this pi before using debian and it worked, so I don't think it's my router but of course anything is possible.

  Read the article

• Centos does not open port/s after the rule/s are appended

  - by Charlie Dyason

  So after some battling and struggling with the firewall, i see that I may be doing something or the firewall isnt responding correctly there is has a port filter that is blocking certain ports. by the way, I have combed the internet, posted on forums, done almost everything and now hence the website name "serverfault", is my last resort, I need help What I hoped to achieve is create a pptp server to connect to with windows/linux clients UPDATED @ bottom Okay, here is what I did: I made some changes to my iptables file, giving me endless issues and so I restored the iptables.old file contents of iptables.old: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT after iptables.old restore(back to stock), nmap scan shows: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 13:54 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.014s latency). Not shown: 997 filtered ports PORT STATE SERVICE 22/tcp open ssh 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 4.95 seconds if I append rule: (to accept all tcp ports incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 13:58 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 3.77 seconds *notice it allows and opens port 443 but no other ports, and it removes port 113...? removing previous rule and if I append rule: (allow and open port 80 incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -p tcp --dport 80 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:01 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.014s latency). Not shown: 996 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 5.12 seconds *notice it removes port 443 and allows 80 but is closed without removing previous rule and if I append rule: (allow and open port 1723 incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -p tcp --dport 1723 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:05 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.015s latency). Not shown: 996 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 5.16 seconds *notice no change in ports opened or closed??? after removing rules: iptables -A INPUT -i eth0 -m tcp -p tcp --dport 80 -j ACCEPT iptables -A INPUT -i eth0 -m tcp -p tcp --dport 1723 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:07 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.015s latency). Not shown: 998 filtered ports PORT STATE SERVICE 22/tcp open ssh 113/tcp closed ident Nmap done: 1 IP address (1 host up) scanned in 5.15 seconds and returning rule: (to accept all tcp ports incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:07 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 3.87 seconds notice the eth0 changes the 999 filtered ports to 858 filtered ports, 139 closed ports QUESTION: why cant I allow and/or open a specific port, eg. I want to allow and open port 443, it doesnt allow it, or even 1723 for pptp, why am I not able to??? sorry for the layout, the editor was give issues (aswell... sigh) UPDATE @Madhatter comment #1 thank you madhatter in my iptables file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT # ----------all rules mentioned in post where added here ONLY!!!---------- -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT if I want to allow and open port 1723 (or edit iptables to allow a pptp connection from remote pc), what changes would I make? (please bear with me, my first time working with servers, etc.) Update MadHatter comment #2 iptables -L -n -v --line-numbers Chain INPUT (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 9 660 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 3 0 0 ACCEPT all -- eth0 * 0.0.0.0/0 0.0.0.0/0 4 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 5 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 6 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT 6 packets, 840 bytes) num pkts bytes target prot opt in out source destination just on a personal note, madhatter, thank you for the support , I really appreciate it! UPDATE MadHatter comment #3 here are the interfaces ifconfig eth0 Link encap:Ethernet HWaddr 00:1D:D8:B7:1F:DC inet addr:[server ip] Bcast:[server ip x.x.x].255 Mask:255.255.255.0 inet6 addr: fe80::21d:d8ff:feb7:1fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36692 errors:0 dropped:0 overruns:0 frame:0 TX packets:4247 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2830372 (2.6 MiB) TX bytes:427976 (417.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) remote nmap nmap -p 1723 [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-11-01 16:17 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). PORT STATE SERVICE 1723/tcp filtered pptp Nmap done: 1 IP address (1 host up) scanned in 0.51 seconds local nmap nmap -p 1723 localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-11-01 16:19 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000058s latency). Other addresses for localhost (not scanned): 127.0.0.1 PORT STATE SERVICE 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.11 seconds UPDATE MadHatter COMMENT POST #4 I apologize, if there might have been any confusion, i did have the rule appended: (only after 3rd post) iptables -A INPUT -p tcp --dport 1723 -j ACCEPT netstat -apn|grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1142/pptpd There are not VPN's and firewalls between the server and "me" UPDATE MadHatter comment #5 So here is an intersting turn of events: I booted into windows 7, created a vpn connection, went through the verfication username & pword - checking the sstp then checking pptp (went through that very quickly which meeans there is no problem), but on teh verfication of username and pword (before registering pc on network), it got stuck, gave this error Connection failed with error 2147943625 The remote computer refused the network connection netstat -apn | grep -w 1723 before connecting: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd after the error came tried again: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd tcp 0 0 41.185.26.238:1723 41.13.212.47:49607 TIME_WAIT - I do not know what it means but seems like there is progress..., any thoughts???

  Read the article

• pptpd configuration

  - by Ian R.

  I would like a little help on configuring pptp so I can use my server as a vpn server since I have 10 ip's on it and I travel a lot so that would really help me and my partners. I managed to install everything needed but my vpn client fails to connect due to some reason that I cannot understand. I know there are 2 files in pptp that you're supposed to edit so I will post my 2 files here: /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 proxyarp nodefaultroute lock nobsdcomp /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip xx.158.177.231 remoteip xx.158.177.103,xx.158.177.116,xx.158.177.121,xx.158.177.124,xx.158.177.125,xx.158.177.131,xx.158.177.134,xx.158.177.139,xx.158.177.142,xx.158.177.145 interfaces file eth0 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.231 Bcast:xx.158.177.255 Mask:255.255.254.0 inet6 addr: xx80::216:3eff:fe51:31ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:56352 errors:0 dropped:0 overruns:0 frame:0 TX packets:3xx15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4884030 (4.8 MB) TX bytes:6780974 (6.7 MB) Interrupt:16 eth0:1 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.103 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:2 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.116 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:3 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.121 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:4 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.124 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:5 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.125 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:6 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.131 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:7 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.134 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:8 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.139 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:9 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.142 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 eth0:10 Link encap:Ethernet HWaddr 00:16:3e:51:31:ba inet addr:xx.158.177.145 Bcast:xx.158.177.255 Mask:255.255.254.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:3 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:286 (286.0 B) TX bytes:286 (286.0 B)

  Read the article

• Routing all data through an VPN tunnel with ppp

  - by Oliver

  I'm trying to create a VPN tunnel that forwards all data from the local machine to the VPN server. I'm using ppp-2.4.5 for this with the following configuration: pty "pptp <VPNServer> --nolaunchpppd" name <my login name> remotename PPTP usepeerdns require-mppe-128 file /etc/ppp/options.pptp persist maxfail 0 holdoff 5 I have a script in if-up.d with the following content: route del default eth0 route add default dev ppp0 Before starting the VPN tunnel my routing looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 2 0 0 eth0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 After starting the tunnel (via pon) it looks like: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 ppp0 12.34.56.1 0.0.0.0 255.255.255.255 UH 0 0 0 ppp0 127.0.0.0 127.0.0.1 255.0.0.0 UG 0 0 0 lo 192.168.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 Now the problem is, that the VPN tunnel seems to be looped into itself. If I run ifconfig after a few seconds without any traffic: eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet 192.168.0.10 netmask 255.255.0.0 broadcast 192.168.255.255 ether 00:01:2e:2f:ff:35 txqueuelen 1000 (Ethernet) RX packets 39931 bytes 6784614 (6.4 MiB) RX errors 0 dropped 90 overruns 0 frame 0 TX packets 34980 bytes 7633181 (7.2 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 device interrupt 20 memory 0xfbdc0000-fbde0000 ppp0: flags=4305<UP,POINTOPOINT,RUNNING,NOARP,MULTICAST> mtu 1496 inet 12.34.56.78 netmask 255.255.255.255 destination 12.34.56.1 ppp txqueuelen 3 (Point-to-Point Protocol) RX packets 7 bytes 94 (94.0 B) RX errors 0 dropped 0 overruns 0 frame 0 TX packets 782863 bytes 349257986 (333.0 MiB) TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 It states that already over 300 MiB have been send, ppp0 is only online since a few seconds and the connection isn't working anyway. Can someone please help me to fix the routing table, so that the traffic from ppp0 is not send again through ppp0 but instead goes to the remote server?

  Read the article

• Second network card configuration not working.

  - by Sebas

  I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

  Read the article

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• Can't ping Ip over bridge

  - by tmn29a

  I'm unable to ping another host over a bridge I created, I can't see the error -.- It's a remote machine running debian stable with some backports for which I want to set up DHCP on the new Subnet 172.30.xxx.xxx to be used for KVM-Guests. ifconfig : bond0 Link encap:Ethernet HWaddr e4:11:5b:d4:94:30 inet addr:10.54.2.84 Bcast:10.54.2.127 Mask:255.255.255.192 inet6 addr: fe80::e611:5bff:fed4:9430/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:34277 errors:0 dropped:0 overruns:0 frame:0 TX packets:18379 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2638709 (2.5 MiB) TX bytes:2887894 (2.7 MiB) br0 Link encap:Ethernet HWaddr f2:fc:4d:7f:15:f0 inet addr:172.30.254.66 Bcast:172.30.254.127 Mask:255.255.255.192 inet6 addr: fe80::f0fc:4dff:fe7f:15f0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:252 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:10800 (10.5 KiB) Pings : ping -I br0 172.30.xxx.65 PING 172.30.xxx.65 (172.30.xxx.65) from 172.30.xxx.66 br0: 56(84) bytes of data. --- 172.30.xxx.65 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2017ms ping -I bond0 172.30.254.65 PING 172.30.xxx.65 (172.30.xxx.65) from 10.54.2.84 bond0: 56(84) bytes of data. 64 bytes from 172.30.x.65: icmp_req=1 ttl=64 time=0.599 ms 64 bytes from 172.30.x.65: icmp_req=2 ttl=64 time=0.575 ms 64 bytes from 172.30.x.65: icmp_req=3 ttl=64 time=0.565 ms --- 172.30.x.65 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 1999ms rtt min/avg/max/mdev = 0.565/0.579/0.599/0.031 ms Route : Destination Gateway Genmask Flags Metric Ref Use Iface 172.30.x.64 * 255.255.255.192 U 0 0 0 br0 10.54.x.64 * 255.255.255.192 U 0 0 0 bond0 default 10.54.x.65 0.0.0.0 UG 0 0 0 bond0 default 172.30.x.65 0.0.0.0 UG 0 0 0 br0 The Interface : cat /etc/network/interfaces auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.54.x.84 netmask 255.255.255.192 network 10.54.x.64 gateway 10.54.x.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports bond0 address 172.30.x.66 broadcast 172.30.x.127 netmask 255.255.x.192 gateway 172.30.x.65 bridge_maxwait 0 If you need more info please ask. Thanks for your help !

  Read the article

• Why is Linux choosing the wrong source ip address

  - by Scheintod

  and what to do to let it choose the right one? This all happens inside an OpenVZ container: The Host is Debian/Wheezy with Redhat/OpenVZ Kernel: root@mycl2:~# uname -a Linux mycl2 2.6.32-openvz-042stab081.5-amd64 #1 SMP Mon Sep 30 16:40:27 MSK 2013 x86_64 GNU/Linux The container has two (virtual) network interfaces. One in public and one in private address-space: root@mycl2:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:775 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:32059 (31.3 KiB) TX bytes:56309 (54.9 KiB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:80.123.123.29 P-t-P:80.123.123.29 Bcast:80.123.123.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.0.1.29 P-t-P:10.0.1.29 Bcast:10.0.1.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 The route to the private network is set manually: root@mycl2:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 venet0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 venet0 Tring to ping others on the private network leads to the wrong source address been choosen: root@mycl2:~# ip route get 10.0.1.26 10.0.1.26 dev venet0 src 80.123.123.29 cache mtu 1500 advmss 1460 hoplimit 64 Why is this and what can I do about it? EDIT: If I create the route with (thanks to Joshua) ip route add 10.0.0.0/8 dev venet0 src 10.0.1.29 it is working. But according to man ip-route the src parameter should only set the source-ip if this route is chosen. But if this route is chosen then the source-ip would be that anyway.

  Read the article

• [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

  - by Beco

  I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >