Search Results

Search found 4909 results on 197 pages for 'vendor lock in'.

Page 110/197 | < Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• df -h showing wrong output in GB

  - by Anurag Uniyal

  If I list df output for KB, MB and GB, they do not match e.g. $ df -k |grep xvdb /dev/xvdb1 12796048 732812 11413172 7% /xxx $ df -m |grep xvdb /dev/xvdb1 12497 716 11146 7% /xxx $ df -h |grep xvdb /dev/xvdb1 13G 716M 11G 7% /xxx 12796048 KB = 12496.14 MB so that is slight off but OK 12796048 KB = 12.2 GB, 12407 MB is also 12.2 GB so why df is showing 13 GB or am I missing something? Here is full df listing $ df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.5G 1.7G 5.5G 24% / none 5.8G 128K 5.8G 1% /dev none 5.8G 0 5.8G 0% /dev/shm none 5.8G 44K 5.8G 1% /var/run none 5.8G 0 5.8G 0% /var/lock none 5.8G 0 5.8G 0% /lib/init/rw /dev/xvdb1 13G 716M 11G 6% /xxx Coreutils version seems to 7.4 as info coreutils shows This manual documents version 7.4 of the GNU core utilities,

  Read the article

• Unable to create context rendering error whet run OpenGL application

  - by Rodnower

  Hello, I try to run Mesa gears example and I get following error: freeglut (./gears): Unable to create direct context rendering for window 'Gears' This may hurt performance. though the application runs successfully, but I guess that in future I will have much problems with productivity. I run Linux CentOS 5 on WMvare 7. Mesa's version is 6.5 Relevant output of lspci -v gives: 00:0f.0 VGA compatible controller: VMware SVGA II Adapter (prog-if 00 [VGA controller]) Subsystem: VMware SVGA II Adapter Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at 10d0 [size=16] Memory at d0000000 (32-bit, non-prefetchable) [size=128M] Memory at d8000000 (32-bit, non-prefetchable) [size=8M] [virtual] Expansion ROM at 30000000 [disabled] [size=32K] Capabilities: [40] Vendor Specific Information Any one have idea? There is driver of vmvare for CentOS? Thank you for ahead.

  Read the article

• What's Your Favorite Harmless Computer Practical Joke?

  - by Ben Griswold

  A couple of months ago, I returned from lunch to find that typing any key launched a random application. As I always lock my machine before walking away from it, my first thought was that a co-worker was playing a practical joke on me. As it turned out, the cause was random computer wonkiness. But just in case there's a need :), what's your favorite harmless computer practical joke? For example, would you alter host file entries to direct google.com to a random site or would you put tape over the optical sensor of a co-worker’s mouse?

  Read the article

• How to use auto-discovery with iDRAC Enterprise?

  - by jwiz

  All I want to do is: have "auto discovery" enabled on my iDRAC enterprise at the factory rack the server, cable iDRAC to dhcp-enabled management network have the iDRAC DHCP, find the "Provisioning Server", and get updated with login credentials (for us to use with racadm, idrac webui, etc.) I don't need to do any configuring of the system, install OS, or anything else. I just want idrac to dhcp out of the box, and end up with an account that can be used to login. All the docs I can find on Dell's site refer to a "Provisioning Server", but I honestly can't tell if they have some reference product, or if they only have software that "integrates" with other vendor's existing management systems. I'd be happy to set up whatever is needed, I just can't find something that explicitly describes the process (only references to the fact that it is supported).

  Read the article

• ubuntu server slowly filling up

  - by Crash893

  We had our samba server (ubuntu 8.04 ltr) share fill up the other day but when I went to look at it I cant see any of the shares have to much on them we have 5 group shares and then each users has an individual share one users has 22gigs of stuff a few others have 10-20mb of stuff and everyone else is empty so maybe like 26gigs total I deleted a few files yesterday and freed up about 250mb of space today when i checked it it was completely full again and i deleted some older files and freed up about 170mb of stuff but i can watch it slowly creep down in free space. I keep running a df -h Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 241690180 229340500 169200 100% / varrun 257632 260 257372 1% /var/run varlock 257632 0 257632 0% /var/lock udev 257632 72 257560 1% /dev devshm 257632 52 257580 1% /dev/shm lrm 257632 40000 217632 16% /lib/modules/2.6.24-28-generic /volatile what can I do to try to hunt down whats taking up so much of my hdd? (im fairly new to unix in general so i apologize if this is not well explained)

  Read the article

• ubuntu server slowly filling up

  - by Crash893

  We had our samba server (ubuntu 8.04 ltr) share fill up the other day but when I went to look at it I cant see any of the shares have to much on them we have 5 group shares and then each users has an individual share one users has 22gigs of stuff a few others have 10-20mb of stuff and everyone else is empty so maybe like 26gigs total I deleted a few files yesterday and freed up about 250mb of space today when i checked it it was completely full again and i deleted some older files and freed up about 170mb of stuff but i can watch it slowly creep down in free space. I keep running a df -h Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 241690180 229340500 169200 100% / varrun 257632 260 257372 1% /var/run varlock 257632 0 257632 0% /var/lock udev 257632 72 257560 1% /dev devshm 257632 52 257580 1% /dev/shm lrm 257632 40000 217632 16% /lib/modules/2.6.24-28-generic /volatile what can I do to try to hunt down whats taking up so much of my hdd? (im fairly new to unix in general so i apologize if this is not well explained)

  Read the article

• Third party biometric software.

  - by Iszi

  Most of us with fingerprint readers and such devices probably use the software provided by the vendor, to enable biometric OS login or single sign-on functionality. However, I've recently wondered if there is any third-party software that will do the same thing? This would be similar to how you don't need the manufacturer's software to use a scanner, printer, or webcam - you just use their drivers and your choice of software. Is there anything like this for fingerprint readers or other biometric devices? Free or Open Source projects are preferred, but I'd be interested in learning about any existing solutions regardless. I personally am particularly interested in Windows-compatible software, but I'll leave the query open for any OS.

  Read the article

• Ubuntu 12 Server messing up my hard disk

  - by Jeroen Jacobs

  I'm installing Ubuntu server on a disk with 12GB available. During the setup, I choose the default LVM-based partition layout. However for some reason, Ubuntu decides that it only wants to use 4GB of this disk. How do I reclaim the remaining space of the hard disk? "lvextent" doesn't work btw... output of df -h: Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 4.3G 3.4G 754M 82% / udev 3.9G 4.0K 3.9G 1% /dev tmpfs 1.6G 756K 1.6G 1% /run none 5.0M 0 5.0M 0% /run/lock none 3.9G 0 3.9G 0% /run/shm /dev/sda1 228M 25M 192M 12% /boot output of pvdisplay: --- Physical volume --- PV Name /dev/sda5 VG Name ubuntu PV Size 12.32 GiB / not usable 2.00 MiB Allocatable yes PE Size 4.00 MiB Total PE 3154 Free PE 8 Allocated PE 3146 PV UUID dD06RZ-kGcL-1tTX-Ruds-XIDG-ssMd-FIUkzZ my partitions: Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 26343423 12920833 5 Extended /dev/sda5 501760 26343423 12920832 8e Linux LVM when I try lvextent, it says there is not enough diskspace.

  Read the article

• Unable to Get IIS Response Times with Hyperic Monitoring Tool

  - by jwmajors81

  We have a very large .NET application (vendor) that I am trying to gather performance metrics for using Hyperic. In general I wanted to be able to report response times for each of the components within the application, which include: Web Services ASP.NET Pages MSMQ I am currently unable to successfully monitor the response times for IIS on my windows machines. I have successfully auto-discovered them and I am getting diagnostic information, but am not getting back the response times. After looking online at what other people are seeing, I found that I am missing a tab for the response times which is usually next to the metrics tab. Also, when I look at the configuration screen for IIS I do not see a field which enables me to specify where the log files are located at. Please note that my logs are located at e:\LogFiles\ instead of the usual location because our IT staff doesn't allocate much space for the C: drive. Please note that I have the MSMQ monitors up and running great. Any assistance would be greatly appreciated. Thanks, Jeremy

  Read the article

• Citrix ICA Client on Mac shift key doesn't work as expected.

  - by brianegge

  When I'm connected to a Windows XP computer from my Mac OS X 10.6 using the Citrix ICA Client, it seems that the shift key only works for the first letter typed after pressing shift. In order to type multiple uppercase letters, like ICA, I must either press caps lock, or press and release shift before each character. I've tried switching between standard and enhanced keyboard, as well as the 'Send Special Keys Unchanged' option, but none of these seem to affect the issue. The problem doesn't occur when I switch from the Citrix window to a regular Mac window.

  Read the article

• How to switch users without entering password

  - by torbengb

  I'm a newbie running Ubuntu 9.10. I have two users (wife and me), and each user's screensaver is set to lock so that on wakeup, we get to choose which user's desktop to go to. However, Ubuntu requires a password, so this is pretty tedious. I'd like to switch users without entering any password. I know about this trick that works for the boot login, but it doesn't deal with multiple users. Is it possible to set empty passwords for users in Ubuntu, or skip the password in other ways? (I'm expecting real Linux users to suggest that passwordless users must not get any rights and there be an admin user with a strong password. Yes, you're right. But that's not what this question is about. Thanks.)

  Read the article

• Best 2x 4GB RAM for a Thinkpad X200s

  - by Tommy Jakobsen

  Hi, I need 2x 4GB RAM, a total of 8GB, in my upcoming Thinkpad X200s laptop. Before buying, I would like your advice on which modules to choose. I've been looking at Corsair's Value Select (P/N: CM3X4GSD1066) RAM, because in my experience they produce good RAM modules. However, Corsair lists 7 clock cycles for their modules while Lenovo lists 5 clock cycles. What do you think? Is Lenovo modules the best choice? Are they the fastest/most stable, or is it the Corsair modules? Or modules from a third vendor? Thanks in advance!

  Read the article

• How can I tell if I have PCI Express 2.0 or 2.1?

  - by Stefan Lasiewski

  I am looking at a variety of PCI Express cards, such as a SATA RAID Controller and a Video Card. Some of these cards say they only support PCI Express 2.1, not PCI Express 2.0. I know that my motherboard supports PCI Express 2-something, but the manual doesn't say '2.0' or '2.1'. How can I tell if the PCIe slot on my motherboard is PCI Express 2.0 or PCI Express 2.1? Is it possible to determine the PCIe type from the Windows or Linux commandline? I was under the impression that most PCI Express 2.1 devices are backwards compatible with PCI Express 2.0. Is it possible that the vendor is wrong in saying that PCI Express 2.1 is required?

  Read the article

• What should I know before I set up RAID 6 on Linux?

  - by Dan Ellis

  I just ordered five 1TB drives to install as a RAID 6 array in a Linux server (keeping the existing 1TB drive as a boot disk). I want to use Linux MD for RAID rather than a RAID card, to avoid lock-in. The intended use is for storing filesystems for Xen development environments and an AFP server for iPhoto/Aperture/Lightroom. What things should I know before I set it up? For example, what would be a good choice of filesystem, and what chunk size should I use?

  Read the article

• How to install anti-virus without administrative rights?

  - by Rohit

  In situations where the PC has no CD drive and operating a guest account with limited privileges, how to install an anti-virus tool? Malware is not permitting to open any anti-virus vendor's site and also blocking all sites opened via Google that contain the term "online scan". I somehow managed to download through mirror links with a Download Manager as the browser's download was blocked by the malware. But the problem didn't end there. After I downloaded the anti-virus tool, it failed to install because it needed administrative rights. The user didn't know the administrator password. I tried via command line with runas, but it also asks for the administrator password. The OS is Windows XP. How to deal with these type of malwares if there is a scenario that CD drive is not there only Internet is there?

  Read the article

• Capslock turns on intermittenly on Windows Login Screen

  - by NoCarrier

  At first I thought it was a coworker playing a joke on me.. I have a habit of locking my workstation whenever I leave my desk. however i have noticed over the last several years that sometimes the capslock key would be on when I return. I don't notice this until i try typing in my password (which would fail because its in ALL CAPS) and then glance at the now illuminated caps lock key. This has happened on and off across half a dozen workstations on 2000, XP, Vista, and Windows 7. Possible causes I'm losing my mind "feature" in windows? some sort of institutional domain policy at my workplace someone has been messing with me for many many years ?

  Read the article

• Remapping keys on keyboard in Linux

  - by Anuj More

  I am currently using xmodmap for remapping keys like Caps Lock on my keyboard. However, my keyboard has a bunch of keys on the top that are rarely used (Multimedia keyboard with buttons like Internet, Music, Next song, Mute etc) I want to remap these keys to specific commands (Not keys). For example: Pressing the Internet button should fire up my Firefox (/usr/bin/firefox)(which happens only in Windows for me) Also I need to map a specific button to xkill. Is there a way to achieve this? Using: Fedora 14 on GNOME and KDE (both)

  Read the article

• /var/lib/ureadahead/debugfs using up disk space

  - by Keyo

  Running Ubuntu 10.04 and nearly all my drive space is gone. # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 7.3G 6.6G 327M 96% / none 245M 240K 244M 1% /dev none 249M 0 249M 0% /dev/shm none 249M 340K 249M 1% /var/run none 249M 0 249M 0% /var/lock none 249M 0 249M 0% /lib/init/rw /dev/sda1 228M 34M 183M 16% /boot Of course it's not mounted. I read that chmod 0 /sbin/debugfs could fix the problem, but now it just won't mount despite changing the permission to 777. This is a VM running on VirtualBox. I have done a file system check which ran fine. What is this directory and how can I remove it from the system?

  Read the article

• Windows 7 - Move location of Eventlog

  - by Jörg B.

  I am having a particular nasty problem of my main system drive 'disappearing' all of the sudden while the system is running. The vendor somewhat knows about this but has not managed to fix it completely over multiple fw iterations. Problems I have with the support is that I cannot provide any particular system log files/entries to further analyse what might have been going on because, well - windows cannot write to its 'lost' drive before bsod'ing. Is there any way to configure where Windows 7 stores its event logs so that I could specify a second physical hdd?

  Read the article

• How to customize Windows 7 HAL library during installation (BSOD STOP: 0x000000A5)?

  - by koldovsky

  While trying to install Windows 7 x86 Ultimate on Samsung M40 laptop (Pentium M 1.7 Dothan, 2 GB RAM/ 100 GB HDD) i receive BSOD STOP: 0x000000A5: The bios in this system is not fully ACPI compliant. Please contact your system vendor for an updated bios. The bios on the system is updated to latest version. If ACPI is the real source of the issue it means that I possibly could use another HAL library. In Windows XP it is possible to install system with generic HAL library pressing F7 when installer asks to supply drivers, but on Windows 7 I can't find such option. Ironically, Vista installs and works nice, even if they said that Windows 7 is less demanding for hardware. Windows 7 Advisor also tells nothing suspicious. Can anybody tell me how to customize Windows 7 installer to use generic HAL library (if it is possible, of course) or point me to another solution?

  Read the article

• IOGEAR KVM cannot reset admin account

  - by George Horlacher

  According to the manual you can do a cold reset by holding the reset button in for 3 seconds. This does seem to reset it but the username and password are not reset... I've tried the keyboard hotkeys - Num-Lock and minus sign (-) to get into hotkey mode and then use the "r" and "" to reset to factory defaults but that doesnt seem to do anything either. It just reverts to User1. I'm not sure what the default admin username should be but admin doesnt seem to work I need to get to the admin menu to name the ports but cannot get access. Any ideas? Using GCS1758 manual with no luck.

  Read the article

• Passing all traffic through Cloudflare

  - by Nick

  I am new to Linux System Administration and I am experimenting with iptables trying to learn how to really lock down a system with them. And one thing a friend of mine recommended was that there was a way to pass all incoming traffic through Cloudflare so even if attackers resolved the server ip they still couldn't (D)dos it directly. This is exactly what they said: "Simply config your servers iptables to only allow incoming connections from CloudFlares IP ranges then set it to allow only your IP/IP range to connect on port 21 (SSH)" Could someone help me on what command I'd need to run for Ubuntu to get this effect?

  Read the article

• Can't delete a directory on external drive (OS X)

  - by Martin Tóth

  I have a brand new Transcend StoreJet 25M3 (external HDD) mounted to MacBook (Leopard 10.5.8) at /Volumes/Transcend. I copied some data from my old Windows (XP) machine on it, and now, after cleaning some stuff up, I wanted to delete some directories, but this is what happened: $ rmdir My\ Pictures/ rmdir: My Pictures/: Operation not permitted Using Finder just asks for password, but does not delete the directory (sound of "moved to Trash" is played). I thought it's some permission "thing", but: $ ls -l drwxrwxrwx 1 martin staff 32768 5 jan 16:11 My Pictures/ $ sudo rm -rf My\ Pictures rm: My Pictures: Operation not permitted I re-mounted, rebooted (thinking that there's some file lock), but that did not help. What might have happened here? How to delete it?

  Read the article

• Video from vhs via USB capture device on Linux

  - by Juanlu001

  I want to transfer video from a VHS tape to my computer with Arch Linux, using a USB capture device that comes with Roxio Easy VHS to DVD, which I recently bought. I tried to plug in the device, and it was properly recognized. From /var/log/messages.log, em28xx #0: Identified as Pinnacle Dazzle DVC 90/100/101/107 / Kaiser Baas Video to DVD maker / Kworld DVD Maker 2 (card=9) saa7115 3-0025: saa7113 found (1f7113d0e100000) @ 0x4a (em28xx #0) em28xx #0: Config register raw data: 0x50 em28xx #0: AC97 vendor ID = 0xffffffff em28xx #0: AC97 features = 0x6a90 em28xx #0: Empia 202 AC97 audio processor detected em28xx #0: v4l2 driver version 0.1.2 em28xx #0: V4L2 video device registered as video1 em28xx #0: V4L2 VBI device registered as vbi0 Is there any software that enables me to capture video coming from this device? I don't mind if it is console or GUI based.

  Read the article

< Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >