Search Results

Search found 11115 results on 445 pages for 'disk monitoring'.

Page 111/445 | < Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >

  • Error 5 partition table invalid or corrupt

    - by Clodoaldo
    I'm trying to add a second SSD to a Centos 6 system. But I get the Error 5 partition table invalid or corrupt at boot. The system already has a single SSD (sdb) and a pair of HDDs (sd{a,c}) in a RAID 1 array from where it boots. It is as if the new SSD assumes one of the devices of the RAID array. Is it? How to avoid that or rearrange the setup? # cat fstab UUID=967b4035-782d-4c66-b22f-50244fe970ca / ext4 defaults 1 1 UUID=86fd06e9-cdc9-4166-ba9f-c237cfc43e02 /boot ext4 defaults 1 2 UUID=72552a7a-d8ae-4f0a-8917-b75a6239ce9f /ssd ext4 discard,relatime 1 2 UUID=8000e5e6-caa2-4765-94f8-9caeb2bda26e swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 # ll /dev/disk/by-id/ total 0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:0 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:1 -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:2 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a04d7241:8da6023e:f9004352:107a923a -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a22c43b9:f1954990:d3ddda5e:f9aff3c9 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-f403a2d0:447803b5:66edba73:569f8305 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c500383621ff -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c5003838b2e7 -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5e83a97f592139d6 -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5e83a97f592139d6-part1 -> ../../sdb1 # fdisk -l Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x79298ec9 Device Boot Start End Blocks Id System /dev/sdb1 1 14594 117219328 83 Linux Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d99de Device Boot Start End Blocks Id System /dev/sdc1 1 1275 10240000 fd Linux raid autodetect /dev/sdc2 * 1275 1339 512000 fd Linux raid autodetect /dev/sdc3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b3327 Device Boot Start End Blocks Id System /dev/sda1 1 1275 10240000 fd Linux raid autodetect /dev/sda2 * 1275 1339 512000 fd Linux raid autodetect /dev/sda3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/md0: 10.5 GB, 10484641792 bytes 2 heads, 4 sectors/track, 2559727 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md2: 489.1 GB, 489095557120 bytes 2 heads, 4 sectors/track, 119408095 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 524 MB, 524275712 bytes 2 heads, 4 sectors/track, 127997 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table # cat /etc/grub.conf default=0 timeout=5 splashimage=(hd2,1)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.32-220.17.1.el6.x86_64) root (hd2,1) kernel /vmlinuz-2.6.32-220.17.1.el6.x86_64 ro root=UUID=967b4035-782d-4c66-b22f-50244fe970ca rd_MD_UUID=f403a2d0:447803b5:66edba73:569f8305 rd_MD_UUID=a22c43b9:f1954990:d3ddda5e:f9aff3c9 rd_NO_LUKS rd_NO_LVM rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=br-abnt2 crashkernel=auto rhgb quiet initrd /initramfs-2.6.32-220.17.1.el6.x86_64.img

    Read the article

  • DPM - Monitoring is green, Protection has error and Latest rec point is old. How do I interpret that?

    - by LosManos
    How do I read the DPM info in this case? Monitoring says Failed but Protection shows Ok while having a Latest recovery point from last year. Under Monitoring tab I have Failed for Source | Computer | Protection group | Start time Computer\System Protection | MyServerName | Recovery point | 2014-06-09 19:00:00 which shows me that something happened last night. But under Protection tab everything is green. Here I have Protection group member | | Protection status Protection group ..name.. Computer: MyServerName Computer\System protection Bare metal recovery OK ... Latest recovery point: 2013-12-12 06:32:54 My guess is that backup failed last night once, but succeeded later. It then found out that there hasn't been any change since sometime last year and leave it be and flags Ok.

    Read the article

  • Error 22 no such partition on adding a SSD

    - by Clodoaldo
    I'm trying to add a second SSD to a Centos 6 system. But I get the error 22 no such partition at boot. The system already has a single SSD (sdb) and a pair of HDDs (sd{a,c}) in a RAID 1 array from where it boots. It is as if the new SSD assumes one of the devices of the RAID array. Is it? How to avoid that or rearrange the setup? # cat fstab UUID=967b4035-782d-4c66-b22f-50244fe970ca / ext4 defaults 1 1 UUID=86fd06e9-cdc9-4166-ba9f-c237cfc43e02 /boot ext4 defaults 1 2 UUID=72552a7a-d8ae-4f0a-8917-b75a6239ce9f /ssd ext4 discard,relatime 1 2 UUID=8000e5e6-caa2-4765-94f8-9caeb2bda26e swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 # ll /dev/disk/by-id/ total 0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 ata-ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:0 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:1 -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-name-localhost.localdomain:2 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a04d7241:8da6023e:f9004352:107a923a -> ../../md1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-a22c43b9:f1954990:d3ddda5e:f9aff3c9 -> ../../md0 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 md-uuid-f403a2d0:447803b5:66edba73:569f8305 -> ../../md2 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_OCZ-VERTEX3_OCZ-43DSRFTNCLE9ZJXX-part1 -> ../../sdb1 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3 -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMT49E3-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 scsi-SATA_ST3500413AS_5VMTJNAJ-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c500383621ff -> ../../sdc lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part1 -> ../../sdc1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part2 -> ../../sdc2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c500383621ff-part3 -> ../../sdc3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5000c5003838b2e7 -> ../../sda lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part1 -> ../../sda1 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part2 -> ../../sda2 lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5000c5003838b2e7-part3 -> ../../sda3 lrwxrwxrwx. 1 root root 9 Jun 15 23:50 wwn-0x5e83a97f592139d6 -> ../../sdb lrwxrwxrwx. 1 root root 10 Jun 15 23:50 wwn-0x5e83a97f592139d6-part1 -> ../../sdb1 # fdisk -l Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x79298ec9 Device Boot Start End Blocks Id System /dev/sdb1 1 14594 117219328 83 Linux Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000d99de Device Boot Start End Blocks Id System /dev/sdc1 1 1275 10240000 fd Linux raid autodetect /dev/sdc2 * 1275 1339 512000 fd Linux raid autodetect /dev/sdc3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b3327 Device Boot Start End Blocks Id System /dev/sda1 1 1275 10240000 fd Linux raid autodetect /dev/sda2 * 1275 1339 512000 fd Linux raid autodetect /dev/sda3 1339 60802 477633536 fd Linux raid autodetect Disk /dev/md0: 10.5 GB, 10484641792 bytes 2 heads, 4 sectors/track, 2559727 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md2: 489.1 GB, 489095557120 bytes 2 heads, 4 sectors/track, 119408095 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 524 MB, 524275712 bytes 2 heads, 4 sectors/track, 127997 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table # cat /etc/grub.conf default=0 timeout=5 splashimage=(hd2,1)/grub/splash.xpm.gz hiddenmenu title CentOS (2.6.32-220.17.1.el6.x86_64) root (hd2,1) kernel /vmlinuz-2.6.32-220.17.1.el6.x86_64 ro root=UUID=967b4035-782d-4c66-b22f-50244fe970ca rd_MD_UUID=f403a2d0:447803b5:66edba73:569f8305 rd_MD_UUID=a22c43b9:f1954990:d3ddda5e:f9aff3c9 rd_NO_LUKS rd_NO_LVM rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=br-abnt2 crashkernel=auto rhgb quiet initrd /initramfs-2.6.32-220.17.1.el6.x86_64.img

    Read the article

  • What's the most efficient way to reclaim disk space after deleting lots of data from a database on Sybase ASE 15?

    - by Ernie Longmire
    As I understand it, based on some research but zero real-world experience with Sybase ASE, the only way to reclaim disk space once it's been allocated to a database is to export that database, create a new DB with the same schema, and reload all the exported data to the new database. Is this correct, or is there some other method? Then: assuming the above is correct and a full export-recreate-reload is required, what's the most efficient way to do that? Are there tools that will automate all or part of that process? I'm being told we would have to write separate bcp export and import commands for each and every object in the database, which if true sounds easily scriptable by someone who knows Sybase ASE well enough. (I don't.) This seems to me like a really basic housekeeping task, and it feels like I'm missing something obvious.

    Read the article

  • hyper-v fails when attaching more disk to VM. The VM won't start and generates an error

    - by CasperDK
    I'm lost at what to do about this: Hi... System: Windows 2008 R2 Hyper-V farm running with failover cluster with a EVA 4400 as backend. When I attach a new disk to a VM it fails when I try to start it. If I move the VM to another, say node 1, I can add the disk and I can get them to start. If I move the VM back to node 2 where the problem arose and the VM is running, I get an error during live migration and the VM fails back to node1 where it did run... So it's like there is something wrong with Hyper-V on node 2 and not node 1. Also node 3 has the same issue. Restarting the nodes is NOT an option since I will have this problem again at a later time AND because not all the VMs can run on node 1 which means my client company will experience downtime on the VMs not running on node 1. Any fix for this? An update I have missed perhaps? It has been two years... Here are the errors: An error ocurred while attempting to change the state of virtual machine XXX. 'XXX' failed to start. Microsoft Emulated IDE Controller (Instance ID {83F8638B-8DCA-4152-9EDA-2CA8B33039B4}): Failed to power on with Error 'A device attached to the system is not functioning.' Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' 'XXX' failed to start. (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) Microsoft Emulated IDE Controller (Instance ID {83F8638B-8DCA-4152-9EDA-2CA8B33039B4}): Failed to power on with Error 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) 'XXX': Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) 'XXX': Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) An error ocurred while attempting to change the state of virtual machine XXX. 'XXX' failed to start. Microsoft Emulated IDE Controller (Instance ID {83F8638B-8DCA-4152-9EDA-2CA8B33039B4}): Failed to power on with Error 'A device attached to the system is not functioning.' Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' 'XXX' failed to start. (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) Microsoft Emulated IDE Controller (Instance ID {83F8638B-8DCA-4152-9EDA-2CA8B33039B4}): Failed to power on with Error 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) 'XXX': Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) 'XXX': Failed to open attachment 'X:\XXX.vhd'. Error: 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) An error ocurred while attempting to change the state of virtual machine XXX. 'XXX' failed to start. Microsoft Emulated IDE Controller (Instance ID {83F8638B-8DCA-4152-9EDA-2CA8B33039B4}): Failed to power on with Error 'A device attached to the system is not functioning.' Failed to open attachment 'c:\clusterstorage/volume1/XXX.vhd'. Error: 'A device attached to the system is not functioning.' Failed to open attachment 'c:\clusterstorage/volume1\XXX.vhd'. Error: 'A device attached to the system is not functioning.' 'XXX' failed to start. (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) Microsoft Emulated IDE Controller (Instance ID {83F8638B-8DCA-4152-9EDA-2CA8B33039B4}): Failed to power on with Error 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) 'XXX': Failed to open attachment 'c:\clusterstorage/volume1\XXX.vhd'. Error: 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) 'XXX': Failed to open attachment 'c:\clusterstorage/volume1\XXX.vhd'. Error: 'A device attached to the system is not functioning.' (0x8007001F). (Virtual machine 36563C78-65B5-4C40-A52D-689BB39E8B08) In the Hyper-V logs I found some more errors: In the hyper-v VMMS logs I have this: 'ServerName' failed to perform the operation. The virtual machine is not in a valid state to perform the operation. (Virtual machine ID 0A6CC4A9-39D6-4413-8CF0-B6DAA35B68D7)

    Read the article

  • Does a manually initiated crash (bugcheck 0xdeaddead) trigger a disk-check?

    - by Synetech
    Windows has an advanced function built-in that lets a user manually initiate a BSOD. It is a debugging tool used to halt the system in the event of (though not necessarily limited to) a hang or freeze. When used, it causes a BSOD with the string MANUALLY_INITIATED_CRASH1 and whimsical code 0xDEADDEAD. The point to this crash is that it is purposely done by the user, so it is not (or at least should not) be an unpredictable event caused by hardware errors or bad drivers (at least not necessarily bad drivers). The question then is whether performing a manual crash properly flushes the disk caches and such so that the drive is in a valid state when rebooting and thus forgoing the need to have chkdsk run.

    Read the article

  • What would be the optimal disk config for SQL Server 2008 R2?

    - by Kev
    We have a new Dell R710 server that came with the following storage configuration: 8 x 146GB SAS 10k 6Gbps disks 1 x Perc H700 Integrated Controller (2 x 4 disks - 2 ports each supporting 4 disks) What would be the optimal configuration if we were just after performance? What would be the optimal configuration if we were after performance but wanted data resilience. As per 2 above but with a hot standby disk? We plan to run Windows 2008 R2 and SQL Server 2008 R2. Maximising storage capacity isn't a prime concern.

    Read the article

  • Windows Home Server style redundancy/multi-disk-support on Windows Server 2008 R2?

    - by user19597
    I'm setting up a fileserver for our department. It'll be connected to the domain. I want it to have a very large amount of storage (several TB). Ideally, it should also preserve disk space by identifying identical files and only storing them once. It should be fault tollerant so that if one of the drives fails, that drive can be replaced without losing any data. All of these features are available in Microsoft's consumer offering - Windows Home Server. However, I can't find these kind of features within the enterprise Windows Server 2008 R2. Am I missing something? I know that I could buy a Drobo, or similar, and use this instead. However, I would prefer to use a built-in feature of Windows Server should it exist. It seems surprising to me that these features should be available in Home Server but not in an enterprise fileserver.

    Read the article

  • Get corresponding physical disk drives of mountpoints with WMI queries?

    - by Thomas
    Is there a way to retrieve a connection between a mountpoint (a volume which is mounted into the file system instead of mounted to a drive letter) and its belonging physical disk drive(s) with WMI? For example I have got a volume mountpoint on a W2K8 server which is mounted to “C:\Data\” and the mountpoint is spreaded on the physical disk drives 2, 4, and 5 of the server (the Data Management of the Server Manager shows that) but I cannot find a way to get this to know by using WMI. Volumes which have got a drive letter can be connected with the WMI-Classes Win32_DiskDrive -- Win32_DiskDriveToDiskPartition -- Win32_DiskPartition -- Win32_LogicalDiskToPartition -- Win32_LogicalDisk – but the problem is, that volume mountpoints aren’t listed in the class Win32_LogicalDisk, they are only listed in Win32_Volume. And I did not find a way to connect the class Win32_Volume with the class Win32_DiskDrive – there are missing some linking classes. Does anyone know a solution?

    Read the article

  • How do I use an internal SSD as a scratch disk for FCP X?

    - by andrewb
    I'm contemplating setting up my MacBook Air as a video editing machine. If I do this, I'll upgrade to a 256 GB SSD, and I should be able to keep around 100 GB or more free for video editing. The video files would of course be stored externally, but save purchasing some expensive Thunderbolt RAID device (which I suppose is gradually becoming more of an option), it will be slow for read/writes. How can I have a set up where I take advantage of my SSD's speed for a scratch disk/cache for FCP X, but still have the TB(s) of storage of externals? I don't want to have to be moving files constantly back and forth, this is about saving time not wasting it.

    Read the article

  • Norton Ghost 15 prompts for a recovery CD when restoring a disk image. Why?

    - by Zak
    I used ghost 15 to create a drive image. Now I'm trying to restore that image onto identical hardware to recover. However after the whole image has been placed onto the new disk/hardware, at the end of the copy, ghost is asking me to enter the recovery CD. But the recovery CD is in the danged drive(assuming that the recovery CD is the CD used to recover the image)! So first, if I'm just imaging a drive, why is norton asking me for some recovery CD? Second, what recovery CD is norton talking about, if it's not the ghost CD? Does it want me to give it the windows OS recovery CD that sipped with the original hardware? Damn you norton ghost!!!

    Read the article

  • Windows Recovery Console - forgot password

    - by Jason
    I upgraded to Windows XP SP3, which immediately "broke" the laptop - it never booted with SP3 on it. I put in the Windows XP install disk I had originally used to set up the laptop, and it ran for a while, then said there's no hard disk present, so it can't continue. BIOS still sees the hard disk. I put the hard disk in an external USB case, and I can read/write to it with the other laptop. I then put the hard disk back in it's laptop, restarted with the Windows CD, and tried to get into the Recovery Console, but I forgot the password and can't "log on" to the drive. I'd also like to know if I can fix the broken files (which ones?) from the other laptop (via USB), and if I can "log on" to an external disk with the Recovery Console. (Also, the data won't fit on my other laptop, and I don't have all the install CDs for software on the disk.) Any help appreciated.

    Read the article

  • Create mirror software raid with bad blocks hdd. How to check data integrity?

    - by rumburak
    There is error in System event log like this one: "The device, \Device\Harddisk1\DR1, has a bad block." Because of above I created Raid 1 on this disk and other one. I'm using Windows Server 2008 R2 software RAID volumes. Volume in Disk Manager is marked as "Failed Redundancy" and "At Risk". I could command to "Reactivate Disk" and it's starts to re-sync, but after a while it stops and returns to previous state. It stops re-sync on bad block on old disk and creates same error in System event log. Old disk status is Errors, new disk status is Online. How can I check that there is exact copy of the old disk on new one ? It is server machine so I would prefer to keep it running during this check.

    Read the article

  • Windows 7 - swap file on a USB disk? [closed]

    - by Sara Cohen
    Possible Duplicate: How to move the page file to another physical disk location Windows 7 I was given temporarily a PC, running Windows 7 Ultimate. The problem is it's hard drive is full, there are like 250 MB free. The swap file is set to none. It has 4 GB RAM. When I load a few tabs in Chrome or IE and start a game it runs out of memory. I already emptied Recycle Bin, %temp%, etc. Deleting/moving user files or adding RAM is not an option. Now I have a USB 3 7200 RPM drive, it's connected to a USB 3 port and is really fast. Is there a way to create a swap file on that drive?

    Read the article

  • What can I do to give some more love and disk space to my database on Ubuntu?

    - by Yaron Naveh
    I'm new to linux. I've deployed a db to ubuntu server on amazon and found out I'm low on disk space. did df (see below) - and found out that I'm 89% capacity on one file system, but less on others. What does this mean? Do I have a few partitions and can now utilize others besides /dev/xvda1? Also /dev/xvdb seems large, is it safe to put the db in it and only use it? If so do I need to mount it or do something special? $> df -lah Filesystem Size Used Avail Use% Mounted on /dev/xvda1 8.0G 6.7G 914M 89% / proc 0 0 0 - /proc sysfs 0 0 0 - /sys none 0 0 0 - /sys/fs/fuse/connections none 0 0 0 - /sys/kernel/debug none 0 0 0 - /sys/kernel/security udev 3.7G 8.0K 3.7G 1% /dev devpts 0 0 0 - /dev/pts tmpfs 1.5G 164K 1.5G 1% /run none 5.0M 0 5.0M 0% /run/lock none 3.7G 0 3.7G 0% /run/shm /dev/xvdb 414G 199M 393G 1% /mnt

    Read the article

  • How to setup RAM disk drive using python or WMI?

    - by Ming Xie
    Hi, The background of my question is associated with Tesseract, the free OCR engine (1985-1995 by HP, now hosting in Google). It specifically requires an input file and an output file; the argument only takes filename (not stream / binary string), so in order to use the wrapper API such as pytesser and / or python-tesser.py, the OCR temp files must be created. I, however, have a lot of images need to OCR; frequent disk write and remove is inevitable (and of course the performance hit). The only choice I could think about is changing the wrapper class and point the temp file to RAM disk, which bring this problem up. If you have better solution, please let me know. Thanks a lot. -M

    Read the article

  • NTFS disk mounted as fuseblk in ubuntu 12.10 is very slow and a lot of errors when rsync. Is that not a rare thing?

    - by Pablo Marin-Garcia
    I am having problems with a NTFS disk mounted as a fuseblk in my ubuntu 12.10 through external usb3. When I did a 1.1TB backup with rsync the speed was 1-2MB/s (wiht a ext4 disk speed was 70 MB/s before and after trying the NTFS disk). Also after one hour errors started to appear: rsync: write failed on "xxx": No such file or directory recv_files: "yyy" is a directory #but this file is a FILE not a dir ??!! .... As this is the first time I have mounted the NTFS in linux for heavy usage (the data would be used in windows afterwards), I would like to know if this kind of thinks are common o was only that something became unstable in my system and a simply restart would probably have solved it. This leads me to the these questions: Can I trust fuse for manage NTFS disks? Or is a problem of the NTFS tools in linux not yet totally stables for writing? Do people is still suffering from low performance with fuse-NTFS vs ext4 (in the past I have read about people complaining about this)?

    Read the article

  • How to create iso dvd image for use with Mac OS X's "Disk Utility"?

    - by adolf garlic
    This seemed way easier on my pc. I would just pop a blank dvd in the drive, it asked what I wanted to do with it, to which I would respond, "burn dvd with nero" (paraphrasing), then I would pick "new" and just drag and drop the folders in there. Mac appears to have "Disk Utility" which just requires that I 'choose an image' but then doesn't bother to detail: how to do this what the options mean e.g. format "Mac OS Extended (Journaled)" is that ever going to be readable on a non Mac machine? I want to create an ISO standard DVD as per the 'default' you'd get on nero. All the stuff on the web points to doing things with 'Terminal' (the whole point of buying a Mac was to get away from command line jiggery pokery - I'm trying to burn some photos not land a friggin lunar module here!) Please, if you can just provide some simple instructions on what I need to achive this I'd be extremely grateful. Ta muchley in advance.

    Read the article

  • What causes "All-in-one USB Card Reader" to create 6 drives that always appear in Disk Management?

    - by tim11g
    I installed a "All-in-one USB Card Reader" to read SD cards and other media. It has caused six new drives to appear in Disk Management with six new drive letter assignments. These drives and letters are always present, even when there are no cards in the reader. When unused, they are labeled "No Media". Why does this multifunction reader cause these phantom Disks to appear and consume drive letters? Every USB port can (and does) allow removable media to be mounted and assigned a drive letter, and the drive letter assignment "disappears" when the USB drive is removed. Why are these card reader's drives and letters staying allocated permanently? Is there anything that can be done to make the slots work like a typical USB drive? (The reader is in fact connected to USB).

    Read the article

  • What is good server performance monitoring software for Windows?

    - by Luke
    I'm looking for some software to monitor a single server for performance alerts. Preferably free and with a reasonable default configuration. Edit: To clarify, I would like to run this software on a Windows machine and monitor a remote Windows server for CPU/memory/etc. usage alerts (not a single application). Edit: I suppose its not necessary that this software be run remotely, I would also settle for something that ran on the server and emailed me if there was an alert. It seems like Windows performance logs and alerts might be used for this purpose somehow but it was not immediately obvious to me. Edit: Found a neat tool on the coding horror blog, not as useful for remote monitoring but very useful for things you would worry about as a server admin: http://www.winsupersite.com/showcase/winvista_ff_rmon.asp

    Read the article

  • How do I extract all the files in a VHD to a hard disk including permissions?

    - by Middletone
    I'd like to know wha thte best way is to make an exact copy of a vhd image and pu tit onto my hard disk. I've tried xcopy but there seems to be a number of issues rlated to permissions when doing this. Ideally I'd like to copy the bits so that they match exactly on the new drive. I encountered this when trying to restore a vista backup only to discover the idiots work who decided to not let me restore a 400 gig image to a 1 TB drive size. I've sucessfully mounted the drive in Win 7 which is the environment in which I'm trying ot copy these files.

    Read the article

  • Why is my HDD not showing up?

    - by Mike
    I'm on Windows 7, got a new 2 TiB NON-external hard disk. When I plug it in it doesn't show up on the Disk Management list in the Computer Management window (that you get by right-clicking My Computer and selecting "Manage"). At first I thought it was broken, but I could see it using a friend's computer. I've run a full disk scan using the official tool from Western Digital, no problems. I've formatted it and partitioned it at another friends place, I've even encrypted the disk fully without any problems, then mounted it and placed a text file on it with the word "hello" inside and saved the file. When I boot my own computer the disk shows up in BIOS. So the disk is not broken. I've tried changing what SATA slot on the motherboard I stick it in. Makes no difference. After all this: Why won't my Windows 7 discover the disk???

    Read the article

  • how to create iso dvd image for use with mac/osx "Disk Utility"?

    - by adolf garlic
    This seemed way easier on my pc. I would just pop a blank dvd in the drive, it asked what I wanted to do with it, to which I would respond, "burn dvd with nero" (paraphrasing), then I would pick "new" and just drag and drop the folders in there. Mac appears to have "Disk Utility" which just requires that I 'choose an image' but then doesn't bother to detail - how to do this - what the options mean e.g. format "mac OS extended (journaled)" is that ever going to be readable on a non mac machine? I want to create an ISO standard dvd as per the 'default' you'd get on nero. All the stuff on the web points to doing things with 'terminal' (the whole point of buying a mac was to get away from command line jiggery pokery - I'm trying to burn some photos not land a friggin lunar module here!) Please, if you can just provide some simple instructions on what I need to achive this I'd be extremely grateful. Ta muchley in advance.

    Read the article

  • Linux software raid robustness for raid1 vs other raid levels

    - by Waxhead
    I have a raid5 running and now also a raid1 that I set up yesterday. Since raid5 calculates parity it should be able to catch silent data corruption on one disk. However for raid1 the disks are just mirrors. The more I think about it I figure that raid1 is actually quite risky. Sure it will save me from a disk failure but i might not be as good when it comes to protecting the data on disk (who is actually more important for me). How does Linux software raid actually store raid1 type data on disk? How does it know what spindle is giving corrupt data (if the disk(subsystem) is not reporting any errors) If raid1 really is not giving me data protection but rather disk protection is there some tricks I can do with mdadm to create a two disk "raid5 like" setup? e.g. loose capacity but still keep redundancy also for data!?

    Read the article

  • Server hard disk read speed and client download speed, is there a connection? [closed]

    - by Mywiki Witwiki
    Ok so a client's download speed is only as fast as a server's upload speed, and vice versa. Based on the answers to this post: Does upload speed depend upon download speed of the server? In other words, the data transfer rate between the two computers is only as fast as the speed of the "bottleneck". Let's pretend the two computers are in two different networks and both have 100Mbps internet connection. Ben wants a copy of a file in Mark's computer hard disk with 30Mbps read speed. Does this mean that Ben can download the file at a speed of around 30Mbps only, despite having an internet connection faster than 30Mbps?

    Read the article

< Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >