Search Results

Search found 4015 results on 161 pages for 'packet capture'.

Page 111/161 | < Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >

• Wireless router blocking some sites while using ethernet is fine

  - by Micke

  I'm using Windows 7 and my router is a wireless Apple Airport Express that is approximately two years old. Suddenly I can't access some sites (for example www.sthlm.friskissvettis.se, or www.vegetarian-shoes.co.uk, some streamed tv-shows on svtplay.se, and a number of other random sites) when connecting to internet with my router. It worked good until recently and I'm fairly sure this problem emerged when my ISP upgraded from 10/10mbit to 100/10mbit speed. Most other sites like facebook and google works fine. When using my network cable to connect to internet everything works fine and I can access these sites. Firmware is current and I've tried reseting the router to factory defaults. Tried different browsers, and I can't ping the "blocked" sites either. Tracert www.sthlm.friskissvettis.se starts with 10.0.0.1 and continues through a number of long addresses until it says timeout. The last working address before timeout was sth-tcy-ipcore01-ge-0-2-0.neq.dgcsystems.net [83.241.252.13], if it matters. Tracert www.vegetarian-shoes.co.uk also eventually gives me a timeout. When the network cable is plugged in, I still get timeout on tracert www.sthlm.friskissvettis.se even though I can access the site in Chrome. Weird. www.vegetarian-shoes.co.uk doesn't give me a tracert timeout when the cable is plugged in, and I can access the site as usual. I've tried changing DNS servers to use opendns servers instead, but to no use. I've tried pinging these two sites with a lower MTU packet size (with this method: http://www.richard-slater.co.uk/archives/2009/10/23/change-your-mtu-under-vista-or-windows-7/), but still can't access them through ping... I don't know what to do anymore.... any suggestions???

  Read the article

• Determine the time difference between two linux servers

  - by Paul

  I am troubleshooting a latency network issue on a network. It is probably a nic or cabling issue, but while I was going through the process of figuring it out, I was looking at the timings of a ping packet leaving a network card and arriving at another server. Both linux. So I have tcpdump running on both, and I issue a ping from one to the other, and back again, and looking at the timing differences might have shed light on where the latency is coming from. It is an academic exercise now, as I need to eliminate some more fundamental causes, but I was curious as to how this could be achieved. Given that ntpd is installed and running on two servers, how can I confirm the current time discrepency between the two servers, to whatever level of accuracy is possible - given that we are talking about latency on a local lan, which is ideally a millisecond or so. NTP itself is accurate to a couple of ms under good conditions, and as both servers are in the same environment, they should (presumably) achieve a similar level of accuracy, and so should have a time discrepency between them of a only few ms - but how can I check this?

  Read the article

• can't Remote desktop to windows XP, blaming the server side

  - by Jin

  After rebooting my work PC (windows XP sp3) this Wednesday (thank to Microsoft Tuesday), I found that I can't remote desktop to my work PC from home (with VPN to company). I have been remote-desktop to work for years and I am really surprised since connectivity is not the problem, so I brought up wireshark to sniff the packets. I can see after TCP handshake, client sent X.224 Connection Request 03 00 00 13 0e e0 00 00 00 00 00 01 00 08 00 03 00 00 00 server sent X.224 Connection Confirm. 03 00 00 0b 06 d0 00 00 12 34 00 According to "MS-RDPBCGR", the official spec on RDP, the server should include Negotiation Response in the "Connection Confirm" message but it didn't. It's empty. I googled a lot but didn't find any clue on why server did that. By the way, I used the same remote desktop client and can connect to other windows XP PC. Here are a couple of pieces of information that may help to give a clue: Since TCP handshake (server port being 3389), I believe the svchost service is actually running. going to control panel -- system window, --- "Remote" tab, the remote desktop is indeeded checked and it states that my username is allowed. according to the packet capture, client didn't even get a chance to tell server what user was trying to logon. Yes, the progress bar showed up a few seconds and then it went back to the "Remote desktop Connection" window again. Searched "windowsupdate.log", didn't find any appearance of the word "remote".

  Read the article

• Delphi 10, .NET, how do I convert a hex UTF-8 string to its unicode character?

  - by Evan V.

  Hi all, I am trying to make my web app compatible with international languages and I am stuck with trying to convert escaped characters in my Delphi .NET DLL. The front end code is passing the UTF-8 hex notation with an escape character e.g for ? I pass \uE3818A. In my DLL I capture this and constract the following string '$E3828A'. I need to convert this back to ? and send it to my database, I've been trying to use Encoding.UTF8.GetBytes and Encoding.UTF8.GetString but with no luck. Anyone could help me figure this out? Thank you.

  Read the article

• Fast Ethernet module for Cisco 2620

  - by Kenny Rasschaert

  I have a Cisco 2620 Router. It comes with one fast ethernet port built in (circled in red), and one old AUI ethernet module is installed (circled in blue). I figure I can put a transceiver on the AUI interface to get a second RJ45 connector. What I'd really like to have is a second fast ethernet connector. The ideal candidate to achieve this would be the NM-1FE-TX module. Cisco claims on their website that this module is not suitable for the Cisco 2620 and Cisco 2620XM. It says so in "Table 2 Physical Limitation of Serial Modules per Chassis". Indeed, this module was designed for the 3600 series of routers. I've seen claims on the internet, however, of people having this module on a 2620XM, and it being fully functional. This claim gains some credibility because of the fact that in Cisco's own Packet Tracer software, you can install this module on the 2620XM router. I'm looking for a definitive answer. Will this module work on a Cisco 2620? Is there perhaps another way to get a second fast ethernet port on this device?

  Read the article

• Silverlight 4 - encoding PCM data from the microphone

  - by Richard

  Hi I've written a basic SL4 application to capture audio data from the microphone using CaptureSource. The trouble is, it's raw PCM output - which means huge and uncompressed. Given that I need this application to run purely within a SL4 environment, how can I compress the PCM audio data into something that can be delivered to a remote server more easily? In conversation, people have suggested Speex and WMA for instance, but I haven't found any libraries or examples that work without requiring reference to DLL's that won't work in a SL4 project. Thanks, Richard.

  Read the article

• 100% width bg images not extending on horizontal scroll

  - by Fuego DeBassi

  I'm noticing this issue. I made a quick screen capture to demonstrate: http://dl.dropbox.com/u/904456/2010-06-14_2323.swf Basically when you have a min-width set and the viewport goes under that constraint, a horizontal scroll bar appears. Pretty much what you would expect, but when you scroll over horizontally all elements that are suppose to extend across the entire width of the page and have background images/colors different from the body do not extend. If you resize the viewport it seems to catch up. Is this a known issue? You can see it on a lot of sites, http://gowalla.com for example. Any ideas?

  Read the article

• Overriding routes on Openvpn client, iproute, iptables2

  - by sarvavijJana

  I am looking for some way to route packets based on its destination ports switching regular internet connection and established openvpn tunnel. This is my configuration OpenVPN server ( I have no control over it ) OpenVPN client running ubuntu wlan0 192.168.1.111 - internet connected if Several routes applied on connection to openvpn from server: /sbin/route add -net 207.126.92.3 netmask 255.255.255.255 gw 192.168.1.1 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 And I need to route packets regarding it's destination ports for ex: 80,443 into vpn everything else directly to isp connection 192.168.1.1 What i have used during my attempts: iptables -A OUTPUT -t mangle -p tcp -m multiport ! --dports 80,443 -j MARK --set-xmark 0x1/0xffffffff ip rule add fwmark 0x1 table 100 ip route add default via 192.168.1.1 table 100 I was trying to apply this settings using up/down options of openvpn client configuration All my attempts reduced to successful packet delivery and response only via vpn tunnel. Packets routed bypassing vpn i have used some SNAT to gain proper src address iptables -A POSTROUTING -t nat -o $IF -p tcp -m multiport --dports 80,443 -j SNAT --to $IF_IP failed in SYN-ACK like 0 0,1 0,1: "70","192.168.1.111","X.X.X.X","TCP","34314 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18664016 TSER=0 WS=7" "71","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584430 TSER=18654692 WS=5" "72","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584779 TSER=18654692 WS=5" "73","192.168.1.111","X.X.X.X","TCP","34343 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18673732 TSER=0 WS=7" I hope someone has already overcome such a situation or probably knows better approach to fulfill requirements. Please kindly give me a good advice or working solution.

  Read the article

• WPF - Drag from withing DataTemplate

  - by Gustavo Cavalcanti

  I have a ListBox displaying employees with a DataTemplate - it looks very similar to this screenshot. I want to be able to click on the employee photo, drag it and drop it somewhere out of the ListBox. How can I do that? I am not sure how to capture the PreviewMouseLeftButtonDown event of the Image, since it's inside the DataTemplate. Edit: The DataTemplate lives in a separate assembly and the drag/drop logic needs to be in the Window that has the ListBox. Edit2: I am thinking that the right way of doing this is using commands, am I right? Thanks!

  Read the article

• How can a Delphi TForm / TPersistent object calculate its own deserialization time?

  - by mjustin

  For performance tests I need a way to measure the time needed for a form to load its definition from the DFM. All existing forms inherit a custom form class. To capture the current time, this base class needs overriden methods as "extension points": start of the deserialization process after the deserialization (can be implemented by overriding the Loaded procedure) the moment just before the execution of the OnFormCreate event So the log for TMyForm.Create(nil) could look like: - 00.000 instance created - 00.010 before deserialization - 01.823 after deserialization - 02.340 before OnFormCreate Which TObject (or TComponent) methods are best suited? Maybe there are other extension points in the form creation process, please feel free to make suggestions.

  Read the article

• Difference between "traceroute" and "traceroute -U"

  - by AndiDog

  The manpage of traceroute says that the "-U" parameter (UDP probing) is the default, but I'm getting different results every time. With "-U": traceroute -U www.univ-paris1.fr traceroute to www.univ-paris1.fr (193.55.96.121), 30 hops max, 60 byte packets [...] 13 rap-vl165-te3-2-jussieu-rtr-021.noc.renater.fr (193.51.181.101) 59.445 ms 56.924 ms 56.651 ms [...] 18 * paris1web.univ-paris1.fr (193.55.96.121) 23.797 ms 23.603 ms but the normal traceroute gives me another result (never reaches the final node) - it's either "!X" or just exits after the maximum of 30 hops: traceroute www.univ-paris1.fr traceroute to www.univ-paris1.fr (193.55.96.121), 30 hops max, 60 byte packets [...] 11 te1-1-paris1-rtr-021.noc.renater.fr (193.51.189.38) 28.147 ms 28.250 ms 28.538 ms [... non-responding nodes ...] 28 site-1.03-jussieu.rap.prd.fr (195.221.126.58) 85.941 ms !X * * Note: I tried this very often and always get the same results. The path in my local network is always the same. So what does the "-U" parameter actually change here? I'm especially interested what the reason for "!X" could be (communication administratively prohibited). EDIT: If that helps, paris-traceroute gives me the following for the last hop: 14 P(1, 6) site-1.03-jussieu.rap.prd.fr (195.221.126.58) 34.938 ms !5 !T2 which means that node discards the packet with TTL=2 and returns an unknown message (not "destination unreachable" or the like).

  Read the article

• Why can't I route to some sites from my MacBook Pro that I can see from my iPad?

  - by Robert Atkins

  I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

  Read the article

• Redundant OpenVPN connections with advanced Linux routing over an unreliable network

  - by konrad

  I am currently living in a country that blocks many websites and has unreliable network connections to the outside world. I have two OpenVPN endpoints (say: vpn1 and vpn2) on Linux servers that I use to circumvent the firewall. I have full access to these servers. This works quite well, except for the high package loss on my VPN connections. This packet loss varies between 1% and 30% depending on time and seems to have a low correlation, most of the time it seems random. I am thinking about setting up a home router (also on Linux) that maintains OpenVPN connections to both endpoints and sends all packets twice, to both endpoints. vpn2 would send all packets from home to vpn1. Return trafic would be send both directly from vpn1 to home, and also through vpn2. +------------+ | home | +------------+ | | | OpenVPN | | links | | | ~~~~~~~~~~~~~~~~~~ unreliable connection | | +----------+ +----------+ | vpn1 |---| vpn2 | +----------+ +----------+ | +------------+ | HTTP proxy | +------------+ | (internet) For clarity: all packets between home and the HTTP proxy will be duplicated and sent over different paths, to increase the chances one of them will arrive. If both arrive, the first second one can be silently discarded. Bandwidth usage is not an issue, both on the home side and endpoint side. vpn1 and vpn2 are close to each other (3ms ping) and have a reliable connection. Any pointers on how this could be achieved using the advanced routing policies available in Linux?

  Read the article

• What is the actual MSMQ address used by the respective WCF binding?

  - by mark

  Dear ladies and sirs. This question is related to this one. Given that WCF binding uses net.msmq:// URL, for instance net.msmq://server/private/nc_queue, how can one know what is the actual MSMQ address to which this URL is translated? Is there some kind of a trace that can be activated? Or an external tool that would help one capture the address? Thanks. EDIT1 OK, I owe a clarification. One can talk directly to MSMQ through the respective .NET API. In the case of MSMQ over its native port 1801, I would use this MSMQ address: FormatName:Direct=OS:server\private$\nc_queue When MSMQ is configured over HTTP, the address changes to something like this: FormatName:Direct=http://server/msmq/nc_queue But the WCF binding uses a standard URL to describe the address, like: net.msmq://server/private/nc_queue So, how can I know what is the actual MSMQ address (the one with the FormatName) to which the net.msmq:// is translated?

  Read the article

• Getting black images with selenium.captureScreenshot

  - by Lidia

  I'm executing selenium tests with testng, that are started on a remote system with Selenium RC via hudson (with ssh connection). The remote system is windows xp with MKS Toolkit installed, hence ssh. Tests are NOT executed as a windows service. I've tried using both captureScreenshot and captureEntirePageScreenshot methods. The first one always produces a black image. The second one creates the correct screen shot but it only works on Firefox and our tests usually pass on Firefox and fail in other browsers, so it is crucial to capture screen shots for the other browsers (mainly IE and Safari). The tests are ran in parallel, with many browser windows open at the same time. I'm not certain if this is what's causing the problem. Any thoughts will be appreciated.

  Read the article

• need thoughts on my interview question - .net, c#

  - by uno

  One of the questions I was asked was that I have a database table with following columns pid - unique identifier orderid - varchar(20) documentid - int documentpath - varchar(250) currentLocation - varchar(250) newlocation - varchar(250) status - varchar(15) I have to write a c# app to move the files from currentlocation to newlocation and update status column as either 'SUCCESS' or 'FAILURE'. This was my answer Create a List of all the records using linq Create a command object which would be perform moving files using foreach, invoke a delegate to move the files - use endinvoke to capture any exception and update the db accordingly I was told that command pattern and delegate did not fit the bill here - i was aksed to think and implement a more favorable GoF pattern. Not sure what they were looking for - In this day and age, do candidates keep a lot of info on head as one always has google to find any answer and come up with solution.

  Read the article

• what perl regex should I use to get value from line

  - by Octopus

  I am trying to capture the cpu usage from the running process. For SunOS, I have below output process,10050,user1,218,59,0,1271M,1260M,sleep,58.9H,0.02%,java here the cpu % is at 11th field if we separate by comma(,). To get this value I am using below regex regex => q/^process,(?:.*?),((?:\d+)\.(?:\d+))%,java$/, but for the linux system I have below output. process,26190,user1,20,0,1236m,43m,6436,S,0.0,1.1,0:00.00,java, here the cpu usage is at 10th column What regex pattern should i use to get this value. Appreciate for any suggestion.

  Read the article

• How do I handle dojo datagrid cell updates so I can post them back automatically to the server?

  - by Raj

  I am using dojo datagrid to display my data. When the end user edit the cell values it should be updated in the server using ajax calls(when the focus goes out of the cell). Else, I should have a Edit & update/cancel buttons for each row to handle the same feature. But I don know how to place edit & update buttons inside the grid and capture their events. By default dojo updates only local the store value(client side). how can I save the updated cell values into the server? do we need to write any override methods to do so?? I am new to dojo. Any detailed explanation or sample codes would be much appreciated. Could anyone lend a hand to solve this issue?? Thank you Regards, Raj

  Read the article

• What the performance impact of enabling WebSphere PMI

  - by Andrew Whitehouse

  I am currently looking at some JProfiler traces from our WebSphere-based application, and am noticing that a significant amount of CPU time is being spent in the class com.ibm.io.async.AsyncLibrary.getCompletionData2. I am guessing, but I am wondering whether this is PMI-related (and we do have this enabled). My knowledge of PMI is limited, as this is managed by another team. Is it expected that PMI can have this sort of impact? (If so) Is the only option to turn it off completely? Or are there some types of data capture that have a particularly high overhead?

  Read the article

• ProCurve 1800 switch issue

  - by user98651

  I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

  Read the article

• Ruby equivalent of PHP's fopen() method

  - by lagrz

  I'm trying to find out if Ruby has en equivalent of php's fopen() method currently used like this: $fd = fopen("php://stdin", "r"); would that be using ARGV variable? Basically what I plan on doing is forward raw e-mail messages using the .procmailrc file which I already got working in a test php file, but the project requires the use of Ruby. Therefore I'm not 100% sure if using the ARGV variable would work or if somehow I need to capture the e-mail stream by some other means. Any help would be greatly appreciated. Thanks :)

  Read the article

• Pinging an external server through OpenVPN tunnel doesn’t work

  - by qdii

  I have an OpenVPN server and a client, and I want to use this tunnel to access not only 10.0.8.0/24 but the whole internet. So far, pinging the server from the client through the tun0 interface works, and vice versa. However, pinging www.google.com from the client through tun0 doesn’t work (all packets are lost). I figured that I should configure the server so that any packet coming from tun0 in destination of the internet be forwarded, so I came up with this iptables config line: interface_connecting_to_the_internet='eth0' interface_openvpn='tun0' internet_ip_address=`ifconfig "$interface_connecting_to_the_internet" | sed -n s'/.*inet \([0-9.]*\).*/\1/p'` iptables -t nat -A POSTROUTING -o "${interface_connecting_to_the_internet}" -j SNAT --to-source "${internet_ip_address}" echo '1' > /proc/sys/net/ipv4/ip_forward Yet, this doesn’t work, the packets are still lost and I am wondering what could possibly be wrong with my setup. Some details: ip route gives on the server: default via 176.31.127.254 dev eth0 metric 3 10.8.0.0/24 via 10.8.0.2 dev tun0 10.8.0.2 dev tun0 proto kernel scope link src 10.8.0.1 127.0.0.0/8 via 127.0.0.1 dev lo 176.31.127.0/24 dev eth0 proto kernel scope link src 176.31.127.109 ip route gives on the client: default via 192.168.1.1 dev wlan0 proto static 10.8.0.1 via 10.8.0.5 dev tun0 10.8.0.5 dev tun0 proto kernel scope link src 10.8.0.6 127.0.0.0/8 via 127.0.0.1 dev lo scope link 192.168.1.0/24 dev wlan0 proto kernel scope link src 192.168.1.109 client uses wifi adapter wlan0 and TUN adapter tun0. server uses ethernet adapter eth0 and TUN adapter tun0. the VPN spans on 10.0.8.0/24 both client and linux are using Linux 3.6.1.

  Read the article

• OpenVPN: ifup tap0 drops all connections

  - by raspi

  I'm trying to create star shaped "virtual" LAN with OpenVPN which is not connected to physical network. ie. tap0 packets should not go to eth0. Packet should only go through OpenVPN to connected clients. This setup works with my OpenVPN testing machine which runs Virtual Box but not on my actual server which is running on top of Xen. Both servers are running Ubuntu Intrepid. /etc/network/interfaces: iface tap0 inet manual address 10.10.10.1 netmask 255.255.255.0 gateway 10.10.10.1 /etc/openvpn/server.conf mode server tls-server port 1194 proto udp dev tap client-to-client ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/servername.crt key /etc/openvpn/easy-rsa/keys/servername.key dh /etc/openvpn/easy-rsa/keys/dh384.pem ifconfig-pool-persist ipp.txt server-bridge 10.10.10.1 255.255.255.0 10.10.10.128 10.10.10.250 push .route 10.10.10.1 255.255.255.0 keepalive 5 60 comp-lzo persist-key persist-tun status /var/log/openvpn-status.log log-append /var/log/openvpn.log verb 3 user nobody group nogroup ifup tap0 on Virtual Box: everything ok, SSH keeps running. But on Xen SSH connection drops and I have to reboot whole machine. What I'm missing?

  Read the article

• Making a DateTime field in a database automatic?

  - by Mike

  I'm putting together a simple test database to learn MVC with. I want to add a DateTime field to show when the record was CREATED. ID = int Name = Char DateCreated = (dateTime, DateTime2..?) I have a feeling that this type of DateTime capture can be done automatically - but that's all I have, a feeling. Can it be done? And if so how? While we're on the subject: if I wanted to include another field that captured the DateTime of when the record was LAST UPDATED how would I do that. I'm hoping to not do this manually. Many thanks Mike

  Read the article

• Making a DateTime field in SQLExpress database?

  - by Mike

  I'm putting together a simple test database to learn MVC with. I want to add a DateTime field to show when the record was CREATED. ID = int Name = Char DateCreated = (dateTime, DateTime2..?) I have a feeling that this type of DateTime capture can be done automatically - but that's all I have, a feeling. Can it be done? And if so how? While we're on the subject: if I wanted to include another field that captured the DateTime of when the record was LAST UPDATED how would I do that. I'm hoping to not do this manually. Many thanks Mike

  Read the article

< Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >