Search Results

Search found 11288 results on 452 pages for 'git status'.

Page 112/452 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

• How to diagnose failing 6Gbps SATA connection?

  - by whitequark

  I have a Samsung RC530 notebook and OCZ Vertex-3 6Gbps SATA SSD working in AHCI mode. # dmesg | grep DMI SAMSUNG ELECTRONICS CO., LTD. RC530/RC730/RC530/RC730, BIOS 03WD.M008.20110927.PSA 09/27/2011 # lspci -nn 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) # sdparm -a /dev/sda /dev/sda: ATA OCZ-VERTEX3 2.15 At the boot, the following messages are present in dmesg (I am running Debian wheezy @ Linux 3.2.8): # dmesg | grep -iE '(ata|ahci)' [ 5.179783] ahci 0000:00:1f.2: version 3.0 [ 5.179802] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 5.179864] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X [ 5.195424] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode [ 5.195429] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst [ 5.195436] ahci 0000:00:1f.2: setting latency timer to 64 [ 5.204035] scsi0 : ahci [ 5.204301] scsi1 : ahci [ 5.204447] scsi2 : ahci [ 5.204592] scsi3 : ahci [ 5.204682] scsi4 : ahci [ 5.204799] scsi5 : ahci [ 5.204917] ata1: SATA max UDMA/133 abar m2048@0xf7c06000 port 0xf7c06100 irq 42 [ 5.204920] ata2: DUMMY [ 5.204923] ata3: SATA max UDMA/133 abar m2048@0xf7c06000 port 0xf7c06200 irq 42 [ 5.204924] ata4: DUMMY [ 5.204926] ata5: DUMMY [ 5.204927] ata6: DUMMY [ 5.523039] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 5.525911] ata3.00: ATAPI: TSSTcorp CDDVDW SN-208BB, SC00, max UDMA/100 [ 5.531006] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 5.533703] ata3.00: configured for UDMA/100 [ 5.542790] ata1.00: ATA-8: OCZ-VERTEX3, 2.15, max UDMA/133 [ 5.542800] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 5.552751] ata1.00: configured for UDMA/133 [ 5.553050] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX3 2.15 PQ: 0 ANSI: 5 [ 5.559621] scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW SN-208BB SC00 PQ: 0 ANSI: 5 [ 5.564059] sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB) [ 5.564127] sd 0:0:0:0: [sda] Write Protect is off [ 5.564131] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.564158] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.564582] sda: sda1 [ 5.564810] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.572006] sr0: scsi3-mmc drive: 16x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 5.572010] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 5.572189] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 6.717181] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen [ 6.717238] ata1.00: irq_stat 0x08000000, interface fatal error [ 6.717291] ata1: SError: { UnrecovData HostInt 10B8B BadCRC } [ 6.717342] ata1.00: failed command: READ FPDMA QUEUED [ 6.717395] ata1.00: cmd 60/50:00:20:39:58/00:00:00:00:00/40 tag 0 ncq 40960 in [ 6.717396] res 40/00:00:20:39:58/00:00:00:00:00/40 Emask 0x50 (ATA bus error) [ 6.717503] ata1.00: status: { DRDY } [ 6.717553] ata1: hard resetting link [ 7.033417] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.055234] ata1.00: configured for UDMA/133 [ 7.055262] ata1: EH complete [ 7.147280] ata1.00: exception Emask 0x10 SAct 0xf8 SErr 0x280100 action 0x6 frozen [ 7.147340] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.147393] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.147460] ata1.00: failed command: READ FPDMA QUEUED [ 7.147529] ata1.00: cmd 60/08:18:88:17:41/00:00:02:00:00/40 tag 3 ncq 4096 in [ 7.147531] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.147691] ata1.00: status: { DRDY } [ 7.147754] ata1.00: failed command: READ FPDMA QUEUED [ 7.147821] ata1.00: cmd 60/00:20:f8:42:4c/01:00:02:00:00/40 tag 4 ncq 131072 in [ 7.147822] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.147977] ata1.00: status: { DRDY } [ 7.148036] ata1.00: failed command: READ FPDMA QUEUED [ 7.148100] ata1.00: cmd 60/50:28:f8:43:4c/00:00:02:00:00/40 tag 5 ncq 40960 in [ 7.148101] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148255] ata1.00: status: { DRDY } [ 7.148315] ata1.00: failed command: READ FPDMA QUEUED [ 7.148379] ata1.00: cmd 60/00:30:50:98:64/01:00:02:00:00/40 tag 6 ncq 131072 in [ 7.148380] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148534] ata1.00: status: { DRDY } [ 7.148593] ata1.00: failed command: READ FPDMA QUEUED [ 7.148657] ata1.00: cmd 60/00:38:50:99:64/01:00:02:00:00/40 tag 7 ncq 131072 in [ 7.148658] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148813] ata1.00: status: { DRDY } [ 7.148875] ata1: hard resetting link [ 7.464842] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.486794] ata1.00: configured for UDMA/133 [ 7.486822] ata1: EH complete [ 7.546395] ata1.00: exception Emask 0x10 SAct 0x2f SErr 0x280100 action 0x6 frozen [ 7.546470] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.546531] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.546588] ata1.00: failed command: READ FPDMA QUEUED [ 7.546648] ata1.00: cmd 60/00:00:e0:4b:61/01:00:02:00:00/40 tag 0 ncq 131072 in [ 7.546649] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.546794] ata1.00: status: { DRDY } [ 7.546847] ata1.00: failed command: READ FPDMA QUEUED [ 7.546906] ata1.00: cmd 60/00:08:90:2f:48/01:00:02:00:00/40 tag 1 ncq 131072 in [ 7.546907] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547053] ata1.00: status: { DRDY } [ 7.547106] ata1.00: failed command: READ FPDMA QUEUED [ 7.547165] ata1.00: cmd 60/00:10:90:30:48/01:00:02:00:00/40 tag 2 ncq 131072 in [ 7.547166] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547310] ata1.00: status: { DRDY } [ 7.547363] ata1.00: failed command: READ FPDMA QUEUED [ 7.547422] ata1.00: cmd 60/00:18:50:c7:64/01:00:02:00:00/40 tag 3 ncq 131072 in [ 7.547423] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547568] ata1.00: status: { DRDY } [ 7.547621] ata1.00: failed command: READ FPDMA QUEUED [ 7.547681] ata1.00: cmd 60/00:28:e0:4c:61/01:00:02:00:00/40 tag 5 ncq 131072 in [ 7.547682] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547825] ata1.00: status: { DRDY } [ 7.547882] ata1: hard resetting link [ 7.864408] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.886351] ata1.00: configured for UDMA/133 [ 7.886375] ata1: EH complete [ 7.890012] ata1: limiting SATA link speed to 3.0 Gbps [ 7.890016] ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x280100 action 0x6 frozen [ 7.890093] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.890152] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.890210] ata1.00: failed command: READ FPDMA QUEUED [ 7.890272] ata1.00: cmd 60/00:00:90:33:48/01:00:02:00:00/40 tag 0 ncq 131072 in [ 7.890273] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890418] ata1.00: status: { DRDY } [ 7.890472] ata1.00: failed command: READ FPDMA QUEUED [ 7.890530] ata1.00: cmd 60/00:08:90:34:48/01:00:02:00:00/40 tag 1 ncq 131072 in [ 7.890531] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890672] ata1.00: status: { DRDY } [ 7.890724] ata1.00: failed command: READ FPDMA QUEUED [ 7.890781] ata1.00: cmd 60/78:10:e0:4f:61/00:00:02:00:00/40 tag 2 ncq 61440 in [ 7.890782] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890925] ata1.00: status: { DRDY } [ 7.890981] ata1: hard resetting link [ 8.208021] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 8.230100] ata1.00: configured for UDMA/133 [ 8.230124] ata1: EH complete Looks like the SATA interface tries to use 6Gbps link, then fails miserably and Linux fallbacks to 3Gbps. This is somewhat fine for me, as the system boots successfully each time and works under high load (cd linux-3.2.8; make -j16). I've also ran memtest86+ and it did not find any errors. What concerns me more is that Grub sometimes takes a long time to load the images and/or fails to load itself completely. The error is consistent and is probablistic: that is, each time I boot I have a certain chance to fail. Actually, I have a slight suspiction on the cause of the failure. Look at the cabling: What kind of engineer does it this way? Nah. Even 1Gbps Ethernet hardly tolerates cables bent over a small angle, and there you have 6Gbps SATA. How cound I determine and fix the cause of errors and/or switch the link to 3Gbps mode permanently?

  Read the article

• Bundler isn't loading gems

  - by Garrett

  I have been having a problem with using Bundler and being able to access my gems without having to require them somewhere, as config.gem used to do that for me (as far as I know). In my Rails 3 app, I defined my Gemfile like so: clear_sources source "http://gemcutter.org" source "http://gems.github.com" bundle_path "vendor/bundler_gems" ## Bundle edge rails: git "git://github.com/rails/arel.git" git "git://github.com/rails/rack.git" gem "rails", :git => "git://github.com/rails/rails.git" ## Bundle gem "mongo_mapper", :git => "git://github.com/jnunemaker/mongomapper.git" gem "bluecloth", ">= 2.0.0" Then I run gem bundle, it bundles it all up like expected. Inside the environment.rb file that is included within boot.rb it looks like this: # DO NOT MODIFY THIS FILE module Bundler file = File.expand_path(__FILE__) dir = File.dirname(file) ENV["PATH"] = "#{dir}/../../../../bin:#{ENV["PATH"]}" ENV["RUBYOPT"] = "-r#{file} #{ENV["RUBYOPT"]}" $LOAD_PATH.unshift File.expand_path("#{dir}/gems/builder-2.1.2/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/builder-2.1.2/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/text-hyphen-1.0.0/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/text-hyphen-1.0.0/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/i18n-0.3.3/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/i18n-0.3.3/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/arel/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/arel/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activemodel/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activemodel/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/jnunemaker-validatable-1.8.1/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/jnunemaker-validatable-1.8.1/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/abstract-1.0.0/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/abstract-1.0.0/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/erubis-2.6.5/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/erubis-2.6.5/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/mime-types-1.16/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/mime-types-1.16/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/mail-2.1.2/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/mail-2.1.2/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/rake-0.8.7/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/rake-0.8.7/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/railties/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/railties/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/memcache-client-1.7.7/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/memcache-client-1.7.7/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rack/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rack/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/rack-test-0.5.3/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/rack-test-0.5.3/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/rack-mount-0.4.5/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/rack-mount-0.4.5/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/actionpack/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/actionpack/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/bluecloth-2.0.7/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/bluecloth-2.0.7/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/bluecloth-2.0.7/ext") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activerecord/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activerecord/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/text-format-1.0.0/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/text-format-1.0.0/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/actionmailer/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/actionmailer/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/tzinfo-0.3.16/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/tzinfo-0.3.16/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activesupport/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activesupport/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activeresource/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/activeresource/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/rails/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/mongo-0.18.2/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/gems/mongo-0.18.2/lib") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/mongomapper/bin") $LOAD_PATH.unshift File.expand_path("#{dir}/dirs/mongomapper/lib") @gemfile = "#{dir}/../../../../Gemfile" require "rubygems" unless respond_to?(:gem) # 1.9 already has RubyGems loaded @bundled_specs = {} @bundled_specs["builder"] = eval(File.read("#{dir}/specifications/builder-2.1.2.gemspec")) @bundled_specs["builder"].loaded_from = "#{dir}/specifications/builder-2.1.2.gemspec" @bundled_specs["text-hyphen"] = eval(File.read("#{dir}/specifications/text-hyphen-1.0.0.gemspec")) @bundled_specs["text-hyphen"].loaded_from = "#{dir}/specifications/text-hyphen-1.0.0.gemspec" @bundled_specs["i18n"] = eval(File.read("#{dir}/specifications/i18n-0.3.3.gemspec")) @bundled_specs["i18n"].loaded_from = "#{dir}/specifications/i18n-0.3.3.gemspec" @bundled_specs["arel"] = eval(File.read("#{dir}/specifications/arel-0.2.pre.gemspec")) @bundled_specs["arel"].loaded_from = "#{dir}/specifications/arel-0.2.pre.gemspec" @bundled_specs["activemodel"] = eval(File.read("#{dir}/specifications/activemodel-3.0.pre.gemspec")) @bundled_specs["activemodel"].loaded_from = "#{dir}/specifications/activemodel-3.0.pre.gemspec" @bundled_specs["jnunemaker-validatable"] = eval(File.read("#{dir}/specifications/jnunemaker-validatable-1.8.1.gemspec")) @bundled_specs["jnunemaker-validatable"].loaded_from = "#{dir}/specifications/jnunemaker-validatable-1.8.1.gemspec" @bundled_specs["abstract"] = eval(File.read("#{dir}/specifications/abstract-1.0.0.gemspec")) @bundled_specs["abstract"].loaded_from = "#{dir}/specifications/abstract-1.0.0.gemspec" @bundled_specs["erubis"] = eval(File.read("#{dir}/specifications/erubis-2.6.5.gemspec")) @bundled_specs["erubis"].loaded_from = "#{dir}/specifications/erubis-2.6.5.gemspec" @bundled_specs["mime-types"] = eval(File.read("#{dir}/specifications/mime-types-1.16.gemspec")) @bundled_specs["mime-types"].loaded_from = "#{dir}/specifications/mime-types-1.16.gemspec" @bundled_specs["mail"] = eval(File.read("#{dir}/specifications/mail-2.1.2.gemspec")) @bundled_specs["mail"].loaded_from = "#{dir}/specifications/mail-2.1.2.gemspec" @bundled_specs["rake"] = eval(File.read("#{dir}/specifications/rake-0.8.7.gemspec")) @bundled_specs["rake"].loaded_from = "#{dir}/specifications/rake-0.8.7.gemspec" @bundled_specs["railties"] = eval(File.read("#{dir}/specifications/railties-3.0.pre.gemspec")) @bundled_specs["railties"].loaded_from = "#{dir}/specifications/railties-3.0.pre.gemspec" @bundled_specs["memcache-client"] = eval(File.read("#{dir}/specifications/memcache-client-1.7.7.gemspec")) @bundled_specs["memcache-client"].loaded_from = "#{dir}/specifications/memcache-client-1.7.7.gemspec" @bundled_specs["rack"] = eval(File.read("#{dir}/specifications/rack-1.1.0.gemspec")) @bundled_specs["rack"].loaded_from = "#{dir}/specifications/rack-1.1.0.gemspec" @bundled_specs["rack-test"] = eval(File.read("#{dir}/specifications/rack-test-0.5.3.gemspec")) @bundled_specs["rack-test"].loaded_from = "#{dir}/specifications/rack-test-0.5.3.gemspec" @bundled_specs["rack-mount"] = eval(File.read("#{dir}/specifications/rack-mount-0.4.5.gemspec")) @bundled_specs["rack-mount"].loaded_from = "#{dir}/specifications/rack-mount-0.4.5.gemspec" @bundled_specs["actionpack"] = eval(File.read("#{dir}/specifications/actionpack-3.0.pre.gemspec")) @bundled_specs["actionpack"].loaded_from = "#{dir}/specifications/actionpack-3.0.pre.gemspec" @bundled_specs["bluecloth"] = eval(File.read("#{dir}/specifications/bluecloth-2.0.7.gemspec")) @bundled_specs["bluecloth"].loaded_from = "#{dir}/specifications/bluecloth-2.0.7.gemspec" @bundled_specs["activerecord"] = eval(File.read("#{dir}/specifications/activerecord-3.0.pre.gemspec")) @bundled_specs["activerecord"].loaded_from = "#{dir}/specifications/activerecord-3.0.pre.gemspec" @bundled_specs["text-format"] = eval(File.read("#{dir}/specifications/text-format-1.0.0.gemspec")) @bundled_specs["text-format"].loaded_from = "#{dir}/specifications/text-format-1.0.0.gemspec" @bundled_specs["actionmailer"] = eval(File.read("#{dir}/specifications/actionmailer-3.0.pre.gemspec")) @bundled_specs["actionmailer"].loaded_from = "#{dir}/specifications/actionmailer-3.0.pre.gemspec" @bundled_specs["tzinfo"] = eval(File.read("#{dir}/specifications/tzinfo-0.3.16.gemspec")) @bundled_specs["tzinfo"].loaded_from = "#{dir}/specifications/tzinfo-0.3.16.gemspec" @bundled_specs["activesupport"] = eval(File.read("#{dir}/specifications/activesupport-3.0.pre.gemspec")) @bundled_specs["activesupport"].loaded_from = "#{dir}/specifications/activesupport-3.0.pre.gemspec" @bundled_specs["activeresource"] = eval(File.read("#{dir}/specifications/activeresource-3.0.pre.gemspec")) @bundled_specs["activeresource"].loaded_from = "#{dir}/specifications/activeresource-3.0.pre.gemspec" @bundled_specs["rails"] = eval(File.read("#{dir}/specifications/rails-3.0.pre.gemspec")) @bundled_specs["rails"].loaded_from = "#{dir}/specifications/rails-3.0.pre.gemspec" @bundled_specs["mongo"] = eval(File.read("#{dir}/specifications/mongo-0.18.2.gemspec")) @bundled_specs["mongo"].loaded_from = "#{dir}/specifications/mongo-0.18.2.gemspec" @bundled_specs["mongo_mapper"] = eval(File.read("#{dir}/specifications/mongo_mapper-0.6.10.gemspec")) @bundled_specs["mongo_mapper"].loaded_from = "#{dir}/specifications/mongo_mapper-0.6.10.gemspec" def self.add_specs_to_loaded_specs Gem.loaded_specs.merge! @bundled_specs end def self.add_specs_to_index @bundled_specs.each do |name, spec| Gem.source_index.add_spec spec end end add_specs_to_loaded_specs add_specs_to_index def self.require_env(env = nil) context = Class.new do def initialize(env) @env = env && env.to_s ; end def method_missing(*) ; yield if block_given? ; end def only(*env) old, @only = @only, _combine_only(env.flatten) yield @only = old end def except(*env) old, @except = @except, _combine_except(env.flatten) yield @except = old end def gem(name, *args) opt = args.last.is_a?(Hash) ? args.pop : {} only = _combine_only(opt[:only] || opt["only"]) except = _combine_except(opt[:except] || opt["except"]) files = opt[:require_as] || opt["require_as"] || name files = [files] unless files.respond_to?(:each) return unless !only || only.any? {|e| e == @env } return if except && except.any? {|e| e == @env } if files = opt[:require_as] || opt["require_as"] files = Array(files) files.each { |f| require f } else begin require name rescue LoadError # Do nothing end end yield if block_given? true end private def _combine_only(only) return @only unless only only = [only].flatten.compact.uniq.map { |o| o.to_s } only &= @only if @only only end def _combine_except(except) return @except unless except except = [except].flatten.compact.uniq.map { |o| o.to_s } except |= @except if @except except end end context.new(env && env.to_s).instance_eval(File.read(@gemfile), @gemfile, 1) end end module Gem @loaded_stacks = Hash.new { |h,k| h[k] = [] } def source_index.refresh! super Bundler.add_specs_to_index end end But when I try to access any of my gems, e.g. MongoMapper, Paperclip, Haml, etc. I get: NameError: uninitialized constant MongoMapper The same goes for any other gem. Does Bundler not include gems like the old Rails 2.0 did? Or is something messed up with my system? Any help would be appreciated, thank you!

  Read the article

• Adding Three20 in our project ?

  - by goeff27

  Hi How to find /Three20/src folder in downloaded source code ? or i have to create my own folder of that name ? and Clone the Three20 git repository: git clone git://github.com/facebook/three20.git is have to run on terminal or what ? Concept not clear ? any any body help me regarding all the steps clearly ? thanks

  Read the article

• Rails auto_complete "undefined method `auto_complete_for'" problem

  - by Andrew Wize

  rails - 2.3.8 ruby - 1.8.7 After auto_complete plugin installstion i still have "undefined method `auto_complete_for'" problem! Andrey-Bezruks-MacBook-Pro:eyeonasia.stage wizeflux$ ruby script/plugin install http://github.com/rails/auto_complete.git --force svn: '/Users/wizeflux/Projects/ionasia/eyeonasia.stage/vendor/plugins' is not a working copy Initialized empty Git repository in /Users/wizeflux/Projects/ionasia/eyeonasia.stage/vendor/plugins/auto_complete/.git/ warning: Option "depth" is ignored for github.com/rails/auto_complete.git From github.com/rails/auto_complete * branch HEAD - FETCH_HEAD Andrey-Bezruks-MacBook-Pro:eyeonasia.stage wizeflux$ after restarting server i get an error on line " auto_complete_for :listings, :name " - undefined method `auto_complete_for' for #

  Read the article

• android - looking for image that goes around a contact in the contacts aplication

  - by Gonzalo Perr

  Hi In the contacts app, from 2.0+ , in the list you can see a border around each contact image. (look at the image) http://thetech24.com/wp-content/uploads/2009/10/Google-Android-2_0_thetech24.com.jpg I have looked around the source code for the contacts app ( [http://android.git.kernel.org/?p=platform/packages/apps/Contacts.git;a=summary][1] ) but coundnt find it. Thanks [1]: http://android.git.kernel.org/?p=platform/packages/apps/Contacts.git;a=summary

  Read the article

• How to use Enum as NamedQuery parameters in JPA

  - by n002213f

  I have an Entity with a enum attribute and a couple on NamedQueries. One of these NamedQueries has a the enum attribute as a parameter i.e. SELECT m FROM Message m WHERE status = :status When i try to ru n the query i get the following error; Caused by: java.lang.IllegalArgumentException: You have attempted to set a value of type class my.package.Status for parameter status with expected type of class my.package.Status from query string SELECT m FROM Message m WHERE m.status = :status. I'm using Toplink How is this? How would i make JPA happy?

  Read the article

• Replace values in a dataframe based on another factor which contains NA's in R

  - by PaulHurleyuk

  I have a dataframe which contains (among other things) a numeric column with a concentration, and a factor column with a status flag. This status flag contains NA's. Here's an example df<-structure(list(conc = c(101.769, 1.734, 62.944, 92.697, 25.091, 27.377, 24.343, 55.084, 0.335, 23.280), status = structure(c(NA, NA, NA, NA, NA, NA, 2L, NA, 1L, NA), .Label = c("<LLOQ", "NR"), class = "factor")), .Names = c("conc", "status"), row.names = c(NA, -10L), class = "data.frame") I want to replace the concentration column with a string for some values of the flag column, or with the concentration value formatted to a certain number of significant digits. When I try this ifelse(df$status=="NR","NR",df$conc) The NA's in the status flag don't trigger either the true or false condition (and return NA) - as the documentation suggests it will. I could loop over the rows and use IF then else on each one but this seems inefficient. Am I missing something ? I've tried as.character(df$status) as well which doesn't work. My mojo must be getting low....

  Read the article

• OSX: Why is GetProcessInformation() causing a segfault?

  - by anthony

  Here's my C method to get the pid of the Finder process. GetProcessInformation() is causing a segfault. Why? Here's the function: static OSStatus GetFinderPID(pid_t *pid) { ProcessSerialNumber psn = {kNoProcess, kNoProcess}; ProcessInfoRec info; OSStatus status = noErr; info.processInfoLength = sizeof(ProcessInfoRec); info.processName = nil; while (!status) { status = GetNextProcess(&psn); if (!status) { status = GetProcessInformation(&psn, &info); } if (!status && info.processType == 'FNDR' && info.processSignature == 'MACS') { return GetProcessPID(&psn, pid); } } return status; } Here's the backtrace: Program received signal EXC_BAD_ACCESS, Could not access memory. Reason: KERN_INVALID_ADDRESS at address: 0x0000000032aaaba7 0x00007fffffe00623 in __bzero () (gdb) bt #0 0x00007fffffe00623 in __bzero () #1 0x00007fff833adaed in CreateFSRef () #2 0x00007fff833ab53b in FSPathMakeRefInternal () #3 0x00007fff852fc32d in _CFGetFSRefFromURL () #4 0x00007fff852fbfe0 in CFURLGetFSRef () #5 0x00007fff85dd273f in GetProcessInformation () #6 0x0000000100000bef in GetFinderPID [inlined] () at /path/to/main.c:21

  Read the article

• In Rails: How can I turn off caching for a particular activerecord database table?

  - by pmneve

  I have an associative table (scripts_runs) (has_many, through) that carries a status column ('started', 'ready to parse', 'completed' ). The started and ready to parse states are signaled by 'flag' files from distributed executions of the scripts pickedup periodically (20 seconds). The completed status is written directly to the associative table by the parser when it is done. With short scripts the complete status is written before the ready to parse flag file is picked up. Because the row from the table is cached, the complete status is not seen by the observer for the flag files and gets overwritten by the ready to parse status. This is not good. I need the status to be updated in the database in the correct sequence so an Ajax periodic query can inform the user of the status of each script and when the run ( consisting of one to many scripts ) is completed. Can I force the ScriptRun.find(:id) to always go to the database? If so how? If not, why not???

  Read the article

• Get only latest row, grouped by a column

  - by Cylindric

  I have a large data-set of emails sent and status-codes. ID Recipient Date Status 1 [email protected] 01/01/2010 1 2 [email protected] 02/01/2010 1 3 [email protected] 01/01/2010 1 4 [email protected] 02/01/2010 2 5 [email protected] 03/01/2010 1 6 [email protected] 01/01/2010 1 7 [email protected] 02/01/2010 2 In this example: all emails sent to someone have a status of 1 the middle email (by date) sent to them has a status of 2, but the latest is 1 the last email sent to others has a status of 2 What I need to retrieve is a count of all emails sent to each person, and what the latest status code was. The first part is fairly simple: SELECT Recipient, Count(*) EmailCount FROM Messages GROUP BY Recipient ORDER BY Recipient Which gives me: Recipient EmailCount [email protected] 2 [email protected] 3 [email protected] 2 How can I get the most recent status code too? The end result should be: Recipient EmailCount LastStatus [email protected] 2 1 [email protected] 3 1 [email protected] 2 2 Thanks. (Server is Microsoft SQL Server 2008, query is being run through an OleDbConnection in .Net)

  Read the article

• How to refactor this Ruby on Rails code?

  - by yuval

  I want to fetch posts based on their status, so I have this code inside my PostsController index action. It seems to be cluttering the index action, though, and I'm not sure it belongs here. How could I make it more concise and where would I move it in my application so it doesn't clutter up my index action (if that is the correct thing to do)? if params[:status].empty? status = 'active' else status = ['active', 'deleted', 'commented'].include?(params[:status]) ? params[:status] : 'active' end case status when 'active' #active posts are not marked as deleted and have no comments is_deleted = false comments_count_sign = "=" when 'deleted' #deleted posts are marked as deleted and have no comments is_deleted = true comments_count_sign = "=" when 'commented' #commented posts are not marked as deleted and do have comments is_deleted = false comments_count_sign = ">" end @posts = Post.find(:all, :conditions => ["is_deleted = ? and comments_count_sign #{comments_count_sign} 0", is_deleted])

  Read the article

• AIR SQLite IN expression not working

  - by goseta

  Hi, I'm having a problem with an expression in my sql statement in SQLite for Adobe AIR basically I have this sql = "UPDATE uniforms SET status=@status WHERE customerId IN(19,20)"; updateStmt.parameters["@status"] = args[1]; updateStmt.execute(); if I run the above code it works, updating the status when the id are 19 and 20 but if I pass the ids list as a parameter like this sql = "UPDATE uniforms SET status=@status WHERE customerId IN(@ids)"; updateStmt.parameters["@status"] = args[1]; updateStmt.parameters["@ids"] = "19,20"; updateStmt.execute(); it gives me and error, saying could not convert text value to numeric value, which make sense because I'm passing and string but the IN expression should convert it accordingly, like it does when I pass directly the list values, why is not working the other way, thanks for any help!

  Read the article

• Getting the value from an array in the model in rails

  - by slythic

  Hi all, I have a relatively simple problem. I have a model named Item which I've added a status field. The status field will only have two options (Lost or Found). So I created the following array in my Item model: STATUS = [ [1, "Lost"], [2, "Found"]] In my form view I added the following code which works great: <%= collection_select :item, :status, Item::STATUS, :first, :last, {:include_blank => 'Select status'} %> This stores the numeric id (1 or 2) of the status in the database. However, in my show view I can't figure out how to convert from the numeric id (again, 1 or 2) to the text equivalent of Lost or Found. Any ideas on how to get this to work? Is there a better way to go about this? Many thanks, Tony

  Read the article

• postgres - group by on multiple columns - master/detail type table

  - by smpillay

  I have a table order(orderid, ordernumber, clientid, orderdesc etc.,) and a corresponding status for that order on an order_status table ( statusid, orderid, statusdesc, statusNote, statustimestamp) say I have a record in order as below orderid orderumber clientid orderdesc 1111 00980065 ABC blah..blah.. and a corresponding status entries statusid orderid statusdesc statusNote statustimestamp 11 1111 recvd status blah yyyy-mm-dd:10:00 12 1111 clientproce status blah yyyy-mm-dd:11:00 13 1111 clientnotice status blah yyyy-mm-dd:15:00 14 1111 notified status blah yyyy-mm-dd:17:00 How can I get the following result (latest timestamp along with multiple columns) 1111 14 00980065 ABC blah..blah.. notified status blah yyyy-mm-dd:17:00

  Read the article

• Getting changes in one column of an historical table

  - by Javi

  Hello, I have a table which stores historical data. It's mapped to an Entity with the following fields (I use JPA with Hibernate implementation): @Entity @Table(name="items_historical") public class ItemHistory{ private Integer id; private Date date; @Enumerated(EnumType.ORDINAL) private StatusEnum status @ManyToOne(optional=false) private User user; @ManyToOne(optional=false) private Item item; } public enum StatusEnum { OK, BAD,...//my status } In every row I store historical data of another table. I need to get the list of the changes on "status" column: the status, the date and the previous status on a specified item (It would be good as well getting the status and date when status was changed). I don't know if this is possible by using HQL. Thanks.

  Read the article

• cant get ajax response (JSON) to call 'success' function?

  - by Haroldo

  for some reason the success function isnt being called? javscript: $.ajax({ type: 'POST', url: 'http://localhost/hf_latest_desktop/st_pages/user_area/acc_buttons/pass_change/pass_change_ajax.php', data: data, dataType: 'json', success: function(e){ console.log(e); if(e.status == 'success'){ alert('your password has been changed!'); } if(e.status == 'error1'){ alert('please fill in all inputs!'); } if(e.status == 'error2'){ alert('password incorrect!'); } if(e.status == 'error3'){ alert('change failed!'); } } }); php file ajax is calling to: <?php session_start(); session_cache_limiter('nocache'); header('Expires: ' . gmdate('r', 0)); header('Content-type: application/json'); $status = 'error1'; //for sake of example ?> {'status':'<?php echo $status; ?>'}

  Read the article

• In Rails models; for symbols get automatically converted to YAML when saving to DB. What is the corr

  - by Ram

  In my model example Game, has a status column. But I usually set status by using symbols. Example self.status = :active MATCH_STATUS = { :betting_on => "Betting is on", :home_team_won => "Home team has won", :visiting_team_won => "Visiting team has one", :game_tie => "Game is tied" }.freeze def viewable_status MATCH_STATUS[self.status] end I use the above Map to switch between viewable status and viceversa. However when the data gets saved to db, ActiveRecord appends "--- " to each status. So when I retrieve back the status is screwed. What should be the correct approach?

  Read the article

• SQL Server Table Polling by Multiple Subscribers

  - by Daniel Hester

  Background Designing Stored Procedures that are safe for multiple subscribers (to call simultaneously) can be challenging.  For example let’s say that you want multiple worker processes to poll a shared work queue that’s encapsulated as a SQL Table. This is a common scenario and through experience you’ll find that you want to use Table Hints to prevent unwanted locking when performing simultaneous queries on the same table. There are three table hints to consider: NOLOCK, READPAST and UPDLOCK. Both NOLOCK and READPAST table hints allow you to SELECT from a table without placing a LOCK on that table. However, SELECTs with the READPAST hint will ignore any records that are locked due to being updated/inserted (or otherwise “dirty”), whereas a SELECT with NOLOCK ignores all locks including dirty reads. For the initial update of the flag (that marks the record as available for subscription) I don’t use the NOLOCK Table Hint because I want to be sensitive to the “active” records in the table and I want to exclude them.  I use an Update Lock (UPDLOCK) in conjunction with a WHERE clause that uses a sub-select with a READPAST Table Hint in order to explicitly lock the records I’m updating (UPDLOCK) but not place a lock on the table when selecting the records that I’m going to update (READPAST). UPDATES should be allowed to lock the rows affected because we’re probably changing a flag on a record so that it is not included in a SELECT from another subscriber. On the UPDATE statement we should explicitly use the UPDLOCK to guard against lock escalation. A SELECT to check for the next record(s) to process can result in a shared read lock being held by more than one subscriber polling the shared work queue (SQL table). It is expected that more than one worker process (or server) might try to process the same new record(s) at the same time. When each process then tries to obtain the update lock, none of them can because another process has a shared read lock in place. Thus without the UPDLOCK hint the result would be a lock escalation deadlock; however with the UPDLOCK hint this condition is mitigated against. Note that using the READPAST table hint requires that you also set the ISOLATION LEVEL of the transaction to be READ COMMITTED (rather than the default of SERIALIZABLE). Guidance In the Stored Procedure that returns records to the multiple subscribers: Perform the UPDATE first. Change the flag that makes the record available to subscribers.  Additionally, you may want to update a LastUpdated datetime field in order to be able to check for records that “got stuck” in an intermediate state or for other auditing purposes. In the UPDATE statement use the (UPDLOCK) Table Hint on the UPDATE statement to prevent lock escalation. In the UPDATE statement also use a WHERE Clause that uses a sub-select with a (READPAST) Table Hint to select the records that you’re going to update. In the UPDATE statement use the OUTPUT clause in conjunction with a Temporary Table to isolate the record(s) that you’ve just updated and intend to return to the subscriber. This is the fastest way to update the record(s) and to get the records’ identifiers within the same operation. Finally do a set-based SELECT on the main Table (using the Temporary Table to identify the records in the set) with either a READPAST or NOLOCK table hint.  Use NOLOCK if there are other processes (besides the multiple subscribers) that might be changing the data that you want to return to the multiple subscribers; or use READPAST if you're sure there are no other processes (besides the multiple subscribers) that might be updating column data in the table for other purposes (e.g. changes to a person’s last name).  NOLOCK is generally the better fit in this part of the scenario. See the following as an example: CREATE PROCEDURE [dbo].[usp_NewCustomersSelect] AS BEGIN -- OVERRIDE THE DEFAULT ISOLATION LEVEL SET TRANSACTION ISOLATION LEVEL READ COMMITTED -- SET NOCOUNT ON SET NOCOUNT ON -- DECLARE TEMP TABLE -- Note that this example uses CustomerId as an identifier; -- you could just use the Identity column Id if that’s all you need. DECLARE @CustomersTempTable TABLE ( CustomerId NVARCHAR(255) ) -- PERFORM UPDATE FIRST -- [Customers] is the name of the table -- [Id] is the Identity Column on the table -- [CustomerId] is the business document key used to identify the -- record globally, i.e. in other systems or across SQL tables -- [Status] is INT or BIT field (if the status is a binary state) -- [LastUpdated] is a datetime field used to record the time of the -- last update UPDATE [Customers] WITH (UPDLOCK) SET [Status] = 1, [LastUpdated] = GETDATE() OUTPUT [INSERTED].[CustomerId] INTO @CustomersTempTable WHERE ([Id] = (SELECT TOP 100 [Id] FROM [Customers] WITH (READPAST) WHERE ([Status] = 0) ORDER BY [Id] ASC)) -- PERFORM SELECT FROM ENTITY TABLE SELECT [C].[CustomerId], [C].[FirstName], [C].[LastName], [C].[Address1], [C].[Address2], [C].[City], [C].[State], [C].[Zip], [C].[ShippingMethod], [C].[Id] FROM [Customers] AS [C] WITH (NOLOCK), @CustomersTempTable AS [TEMP] WHERE ([C].[CustomerId] = [TEMP].[CustomerId]) END In a system that has been designed to have multiple status values for records that need to be processed in the Work Queue it is necessary to have a “Watch Dog” process by which “stale” records in intermediate states (such as “In Progress”) are detected, i.e. a [Status] of 0 = New or Unprocessed; a [Status] of 1 = In Progress; a [Status] of 2 = Processed; etc.. Thus, if you have a business rule that states that the application should only process new records if all of the old records have been processed successfully (or marked as an error), then it will be necessary to build a monitoring process to detect stalled or stale records in the Work Queue, hence the use of the LastUpdated column in the example above. The Status field along with the LastUpdated field can be used as the criteria to detect stalled / stale records. It is possible to put this watchdog logic into the stored procedure above, but I would recommend making it a separate monitoring function. In writing the stored procedure that checks for stale records I would recommend using the same kind of lock semantics as suggested above. The example below looks for records that have been in the “In Progress” state ([Status] = 1) for greater than 60 seconds: CREATE PROCEDURE [dbo].[usp_NewCustomersWatchDog] AS BEGIN -- TO OVERRIDE THE DEFAULT ISOLATION LEVEL SET TRANSACTION ISOLATION LEVEL READ COMMITTED -- SET NOCOUNT ON SET NOCOUNT ON DECLARE @MaxWait int; SET @MaxWait = 60 IF EXISTS (SELECT 1 FROM [dbo].[Customers] WITH (READPAST) WHERE ([Status] = 1) AND (DATEDIFF(s, [LastUpdated], GETDATE()) > @MaxWait)) BEGIN SELECT 1 AS [IsWatchDogError] END ELSE BEGIN SELECT 0 AS [IsWatchDogError] END END Downloads The zip file below contains two SQL scripts: one to create a sample database with the above stored procedures and one to populate the sample database with 10,000 sample records.  I am very grateful to Red-Gate software for their excellent SQL Data Generator tool which enabled me to create these sample records in no time at all. References http://msdn.microsoft.com/en-us/library/ms187373.aspx http://www.techrepublic.com/article/using-nolock-and-readpast-table-hints-in-sql-server/6185492 http://geekswithblogs.net/gwiele/archive/2004/11/25/15974.aspx http://grounding.co.za/blogs/romiko/archive/2009/03/09/biztalk-sql-receive-location-deadlocks-dirty-reads-and-isolation-levels.aspx

  Read the article

• What other protocols must not be fire-walled for FTP to work?

  - by Chris

  my Netgear router randomly reset itself the other day loosing all of my config settings: DSL details, Firewall rules, the lot! So I set about restoring all of the details manually, but when it came to configuring the firewall I wanted improve the security by explicitly setting 'deny' rules for everything that I figured is 'non-essential', and (although not necessary) whilst I was at it I set explicit 'allow' for the 'essential' protocols. I'll admit now I didn't really know what I was doing and everything was just 'my best guess', but I enabled only DNS, HTTP, HTTPS, FTP, SFTP, TFTP with everything else blocked. This did not work for me as I could not access 99% of web sites (although strangely Google worked!), so I played around a bit more and found that (oddly) if I disabled just the explicit 'allow' rules then everything worked fine, for browsing anyway. Today I came to work on some web-sites via FTP and just could not get a consistent connection, it kept dropping out after a few files or being blocked by the server or simply not connecting. It would authenticate okay but then stop when retrieving the initial directory listing! e.g.: Status: Delaying connection for 1 second due to previously failed connection attempt... Status: Resolving address of ftp.domain.co.uk Status: Resolving address of ftp.domain.co.uk Status: Connecting to 123.123.123.123:21... Status: Connecting to 123.123.123.123:21... Status: Connection established, waiting for welcome message... Status: Connection established, waiting for welcome message... Response: 421 Too many connections (8) from this IP Error: Could not connect to server Status: Delaying connection for 5 seconds due to previously failed connection attempt... Response: 421 Too many connections (8) from this IP Error: Could not connect to server Status: Delaying connection for 5 seconds due to previously failed connection attempt... I've checked and re-checked the FTP settings (they worked before anyway), I have Googled the I.T. out of the various protocols that I have blocked in the fire-wall but none seem essential to FTP (other than FTP/SFTP etc. which I have passively enabled). I'm (clearly) no server engineer, or protocols / fire-wall expert so I was hoping that some one could maybe shed some light on why my FTP is failing. I've been wondering if I ought to be allowing BGP, BOOTP and/or IDENT (or any others)? What other protocols are required for FTP? Thanks in advance!

  Read the article

• Access Monit on PHP

  - by xian

  i have a remote server (Centos 5.8) and i have installed monit on it as my monitoring tool. monit installation yum install monit now, on my local machine (still Centos5.8), i want to get the system status (shown below) of the said server provided by monit --------------------------------------------------- | Parameter | Value | --------------------------------------------------- | Name | serverHostname | | Status | Running | | Monitoring mode | active | | Monitoring status | Monitored | | Data collected | Fri, 22 Jun 2012 16:47:01 | | Load average | [0.32] [0.37] [0.43] | | CPU usage | 3.3%us 0.2%sy 0.0%wa | | Memory usage | 2005212 kB [53.9%] | | Swap usage | 893256 kB [21.8%] | --------------------------------------------------- This information is shown when you clicked on the system name link found on the your monit's home page http://localhost:2812 How can I do that in php? How can I retrieve those information? i was thinking of executing this linux command in php: /usr/bin/monit status Output of this is The Monit daemon 5.4 uptime: 2h 55m System 'system_asi454' status Running monitoring status Monitored load average [0.22] [0.34] [0.42] cpu 3.3%us 0.2%sy 0.0%wa memory usage 2005212 kB [53.9%] swap usage 892928 kB [21.8%] data collected Fri, 22 Jun 2012 16:47:01 which is similar to the table content show above.

  Read the article

• Anunciando: Grandes Melhorias para Web Sites da Windows Azure

  - by Leniel Macaferi

  Estou animado para anunciar algumas grandes melhorias para os Web Sites da Windows Azure que introduzimos no início deste verão.  As melhorias de hoje incluem: uma nova opção de hospedagem adaptável compartilhada de baixo custo, suporte a domínios personalizados para websites hospedados em modo compartilhado ou em modo reservado usando registros CNAME e A-Records (o último permitindo naked domains), suporte para deployment contínuo usando tanto CodePlex e GitHub, e a extensibilidade FastCGI. Todas essas melhorias estão agora online em produção e disponíveis para serem usadas imediatamente. Nova Camada Escalonável "Compartilhada" A Windows Azure permite que você implante e hospede até 10 websites em um ambiente gratuito e compartilhado com múltiplas aplicações. Você pode começar a desenvolver e testar websites sem nenhum custo usando este modo compartilhado (gratuito). O modo compartilhado suporta a capacidade de executar sites que servem até 165MB/dia de conteúdo (5GB/mês). Todas as capacidades que introduzimos em Junho com esta camada gratuita permanecem inalteradas com a atualização de hoje. Começando com o lançamento de hoje, você pode agora aumentar elasticamente seu website para além desta capacidade usando uma nova opção "shared" (compartilhada) de baixo custo (a qual estamos apresentando hoje), bem como pode usar a opção "reserved instance" (instância reservada) - a qual suportamos desde Junho. Aumentar a capacidade de qualquer um desses modos é fácil. Basta clicar na aba "scale" (aumentar a capacidade) do seu website dentro do Portal da Windows Azure, escolher a opção de modo de hospedagem que você deseja usar com ele, e clicar no botão "Salvar". Mudanças levam apenas alguns segundos para serem aplicadas e não requerem nenhum código para serem alteradas e também não requerem que a aplicação seja reimplantada/reinstalada: A seguir estão mais alguns detalhes sobre a nova opção "shared" (compartilhada), bem como a opção existente "reserved" (reservada): Modo Compartilhado Com o lançamento de hoje, estamos introduzindo um novo modo de hospedagem de baixo custo "compartilhado" para Web Sites da Windows Azure. Um website em execução no modo compartilhado é implantado/instalado em um ambiente de hospedagem compartilhado com várias outras aplicações. Ao contrário da opção de modo free (gratuito), um web-site no modo compartilhado não tem quotas/limite máximo para a quantidade de largura de banda que o mesmo pode servir. Os primeiros 5 GB/mês de banda que você servir com uma website compartilhado é grátis, e então você passará a pagar a taxa padrão "pay as you go" (pague pelo que utilizar) da largura de banda de saída da Windows Azure quando a banda de saída ultrapassar os 5 GB. Um website em execução no modo compartilhado agora também suporta a capacidade de mapear múltiplos nomes de domínio DNS personalizados, usando ambos CNAMEs e A-records para tanto. O novo suporte A-record que estamos introduzindo com o lançamento de hoje oferece a possibilidade para você suportar "naked domains" (domínios nús - sem o www) com seus web-sites (por exemplo, http://microsoft.com além de http://www.microsoft.com). Nós também, no futuro, permitiremos SSL baseada em SNI como um recurso nativo nos websites que rodam em modo compartilhado (esta funcionalidade não é suportada com o lançamento de hoje - mas chagará mais tarde ainda este ano, para ambos as opções de hospedagem - compartilhada e reservada). Você paga por um website no modo compartilhado utilizando o modelo padrão "pay as you go" que suportamos com outros recursos da Windows Azure (ou seja, sem custos iniciais, e você só paga pelas horas nas quais o recurso estiver ativo). Um web-site em execução no modo compartilhado custa apenas 1,3 centavos/hora durante este período de preview (isso dá uma média de $ 9.36/mês ou R$ 19,00/mês - dólar a R$ 2,03 em 17-Setembro-2012) Modo Reservado Além de executar sites em modo compartilhado, também suportamos a execução dos mesmos dentro de uma instância reservada. Quando rodando em modo de instância reservada, seus sites terão a garantia de serem executados de maneira isolada dentro de sua própria VM (virtual machine - máquina virtual) Pequena, Média ou Grande (o que significa que, nenhum outro cliente da Windows azure terá suas aplicações sendo executadas dentro de sua VM. Somente as suas aplicações). Você pode executar qualquer número de websites dentro de uma máquina virtual, e não existem quotas para limites de CPU ou memória. Você pode executar seus sites usando uma única VM de instância reservada, ou pode aumentar a capacidade tendo várias instâncias (por exemplo, 2 VMs de médio porte, etc.). Dimensionar para cima ou para baixo é fácil - basta selecionar a VM da instância "reservada" dentro da aba "scale" no Portal da Windows Azure, escolher o tamanho da VM que você quer, o número de instâncias que você deseja executar e clicar em salvar. As alterações têm efeito em segundos: Ao contrário do modo compartilhado, não há custo por site quando se roda no modo reservado. Em vez disso, você só paga pelas instâncias de VMs reservadas que você usar - e você pode executar qualquer número de websites que você quiser dentro delas, sem custo adicional (por exemplo, você pode executar um único site dentro de uma instância de VM reservada ou 100 websites dentro dela com o mesmo custo). VMs de instâncias reservadas têm um custo inicial de $ 8 cents/hora ou R$ 16 centavos/hora para uma pequena VM reservada. Dimensionamento Elástico para Cima/para Baixo Os Web Sites da Windows Azure permitem que você dimensione para cima ou para baixo a sua capacidade dentro de segundos. Isso permite que você implante um site usando a opção de modo compartilhado, para começar, e em seguida, dinamicamente aumente a capacidade usando a opção de modo reservado somente quando você precisar - sem que você tenha que alterar qualquer código ou reimplantar sua aplicação. Se o tráfego do seu site diminuir, você pode diminuir o número de instâncias reservadas que você estiver usando, ou voltar para a camada de modo compartilhado - tudo em segundos e sem ter que mudar o código, reimplantar a aplicação ou ajustar os mapeamentos de DNS. Você também pode usar o "Dashboard" (Painel de Controle) dentro do Portal da Windows Azure para facilmente monitorar a carga do seu site em tempo real (ele mostra não apenas as solicitações/segundo e a largura de banda consumida, mas também estatísticas como a utilização de CPU e memória). Devido ao modelo de preços "pay as you go" da Windows Azure, você só paga a capacidade de computação que você usar em uma determinada hora. Assim, se o seu site está funcionando a maior parte do mês em modo compartilhado (a $ 1.3 cents/hora ou R$ 2,64 centavos/hora), mas há um final de semana em que ele fica muito popular e você decide aumentar sua capacidade colocando-o em modo reservado para que seja executado em sua própria VM dedicada (a $ 8 cents/hora ou R$ 16 centavos/hora), você só terá que pagar os centavos/hora adicionais para as horas em que o site estiver sendo executado no modo reservado. Você não precisa pagar nenhum custo inicial para habilitar isso, e uma vez que você retornar seu site para o modo compartilhado, você voltará a pagar $ 1.3 cents/hora ou R$ 2,64 centavos/hora). Isto faz com que essa opção seja super flexível e de baixo custo. Suporte Melhorado para Domínio Personalizado Web sites em execução no modo "compartilhado" ou no modo "reservado" suportam a habilidade de terem nomes personalizados (host names) associados a eles (por exemplo www.mysitename.com). Você pode associar múltiplos domínios personalizados para cada Web Site da Windows Azure. Com o lançamento de hoje estamos introduzindo suporte para registros A-Records (um recurso muito pedido pelos usuários). Com o suporte a A-Record, agora você pode associar domínios 'naked' ao seu Web Site da Windows Azure - ou seja, em vez de ter que usar www.mysitename.com você pode simplesmente usar mysitename.com (sem o prefixo www). Tendo em vista que você pode mapear vários domínios para um único site, você pode, opcionalmente, permitir ambos domínios (com www e a versão 'naked') para um site (e então usar uma regra de reescrita de URL/redirecionamento (em Inglês) para evitar problemas de SEO). Nós também melhoramos a interface do usuário para o gerenciamento de domínios personalizados dentro do Portal da Windows Azure como parte do lançamento de hoje. Clicando no botão "Manage Domains" (Gerenciar Domínios) na bandeja na parte inferior do portal agora traz uma interface de usuário personalizada que torna fácil gerenciar/configurar os domínios: Como parte dessa atualização nós também tornamos significativamente mais suave/mais fácil validar a posse de domínios personalizados, e também tornamos mais fácil alternar entre sites/domínios existentes para Web Sites da Windows Azure, sem que o website fique fora do ar. Suporte a Deployment (Implantação) contínua com Git e CodePlex ou GitHub Um dos recursos mais populares que lançamos no início deste verão foi o suporte para a publicação de sites diretamente para a Windows Azure usando sistemas de controle de código como TFS e Git. Esse recurso fornece uma maneira muito poderosa para gerenciar as implantações/instalações da aplicação usando controle de código. É realmente fácil ativar este recurso através da página do dashboard de um web site: A opção TFS que lançamos no início deste verão oferece uma solução de implantação contínua muito rica que permite automatizar os builds e a execução de testes unitários a cada vez que você atualizar o repositório do seu website, e em seguida, se os testes forem bem sucedidos, a aplicação é automaticamente publicada/implantada na Windows Azure. Com o lançamento de hoje, estamos expandindo nosso suporte Git para também permitir cenários de implantação contínua integrando esse suporte com projetos hospedados no CodePlex e no GitHub. Este suporte está habilitado para todos os web-sites (incluindo os que usam o modo "free" (gratuito)). A partir de hoje, quando você escolher o link "Set up Git publishing" (Configurar publicação Git) na página do dashboard de um website, você verá duas opções adicionais quando a publicação baseada em Git estiver habilitada para o web-site: Você pode clicar em qualquer um dos links "Deploy from my CodePlex project" (Implantar a partir do meu projeto no CodePlex) ou "Deploy from my GitHub project"  (Implantar a partir do meu projeto no GitHub) para seguir um simples passo a passo para configurar uma conexão entre o seu website e um repositório de código que você hospeda no CodePlex ou no GitHub. Uma vez que essa conexão é estabelecida, o CodePlex ou o GitHub automaticamente notificará a Windows Azure a cada vez que um checkin ocorrer. Isso fará com que a Windows Azure faça o download do código e compile/implante a nova versão da sua aplicação automaticamente.  Os dois vídeos a seguir (em Inglês) mostram quão fácil é permitir esse fluxo de trabalho ao implantar uma app inicial e logo em seguida fazer uma alteração na mesma: Habilitando Implantação Contínua com os Websites da Windows Azure e CodePlex (2 minutos) Habilitando Implantação Contínua com os Websites da Windows Azure e GitHub (2 minutos) Esta abordagem permite um fluxo de trabalho de implantação contínua realmente limpo, e torna muito mais fácil suportar um ambiente de desenvolvimento em equipe usando Git: Nota: o lançamento de hoje suporta estabelecer conexões com repositórios públicos do GitHub/CodePlex. Suporte para repositórios privados será habitado em poucas semanas. Suporte para Múltiplos Branches (Ramos de Desenvolvimento) Anteriormente, nós somente suportávamos implantar o código que estava localizado no branch 'master' do repositório Git. Muitas vezes, porém, os desenvolvedores querem implantar a partir de branches alternativos (por exemplo, um branch de teste ou um branch com uma versão futura da aplicação). Este é agora um cenário suportado - tanto com projetos locais baseados no git, bem como com projetos ligados ao CodePlex ou GitHub. Isto permite uma variedade de cenários úteis. Por exemplo, agora você pode ter dois web-sites - um em "produção" e um outro para "testes" - ambos ligados ao mesmo repositório no CodePlex ou no GitHub. Você pode configurar um dos websites de forma que ele sempre baixe o que estiver presente no branch master, e que o outro website sempre baixe o que estiver no branch de testes. Isto permite uma maneira muito limpa para habilitar o teste final de seu site antes que ele entre em produção. Este vídeo de 1 minuto (em Inglês) demonstra como configurar qual branch usar com um web-site. Resumo Os recursos mostrados acima estão agora ao vivo em produção e disponíveis para uso imediato. Se você ainda não tem uma conta da Windows Azure, você pode inscrever-se em um teste gratuito para começar a usar estes recursos hoje mesmo. Visite o O Centro de Desenvolvedores da Windows Azure (em Inglês) para saber mais sobre como criar aplicações para serem usadas na nuvem. Nós teremos ainda mais novos recursos e melhorias chegando nas próximas semanas - incluindo suporte para os recentes lançamentos do Windows Server 2012 e .NET 4.5 (habilitaremos novas imagens de web e work roles com o Windows Server 2012 e NET 4.5 no próximo mês). Fique de olho no meu blog para detalhes assim que esses novos recursos ficarem disponíveis. Espero que ajude, - Scott P.S. Além do blog, eu também estou utilizando o Twitter para atualizações rápidas e para compartilhar links. Siga-me em: twitter.com/ScottGu Texto traduzido do post original por Leniel Macaferi.

  Read the article

• Using Shader causes triangle to disappear

  - by invisal

  The following is my rendering code. Private Sub GameRender() GL.Clear(ClearBufferMask.ColorBufferBit + ClearBufferMask.DepthBufferBit) GL.ClearColor(Color.SkyBlue) GL.UseProgram(theProgram) GL.EnableClientState(ArrayCap.VertexArray) GL.EnableClientState(ArrayCap.ColorArray) GL.BindBuffer(BufferTarget.ArrayBuffer, vertexPositionID) GL.DrawArrays(BeginMode.Triangles, 0, 3) GL.DisableClientState(ArrayCap.ColorArray) GL.DisableClientState(ArrayCap.VertexArray) GlControl1.SwapBuffers() End Sub This is screenshot without GL.UseProgram(theProgram) This is screenshot with GL.UseProgram(theProgram) Here are my shader code that I picked from online tutorial. Vertex Shader #version 330 layout(location = 0) in vec4 position; void main() { gl_Position = position; } Fragment Shader #version 330 out vec4 outputColor; void main() { outputColor = vec4(1.0f, 1.0f, 1.0f, 1.0f); } These are my shader creation code. '' Initialize Shader Dim shaderList(1) As Integer shaderList(0) = CreateShader(ShaderType.VertexShader, strVertexShader) shaderList(1) = CreateShader(ShaderType.FragmentShader, strFragShader) theProgram = CreateProgram(shaderList) GL.DeleteShader(shaderList(0)) GL.DeleteShader(shaderList(1)) Here are my helper functions Private Function CreateShader(ByVal shaderType As ShaderType, ByVal code As String) Dim shader As Integer = GL.CreateShader(shaderType) GL.ShaderSource(shader, code) GL.CompileShader(shader) Dim status As Integer GL.GetShader(shader, ShaderParameter.CompileStatus, status) If status = False Then MsgBox(GL.GetShaderInfoLog(shader)) End If Return shader End Function Private Function CreateProgram(ByVal shaderList() As Integer) As Integer Dim program As Integer = GL.CreateProgram() For i As Integer = 0 To shaderList.Length - 1 GL.AttachShader(program, shaderList(i)) Next GL.LinkProgram(program) Dim status As Integer GL.GetProgram(program, ProgramParameter.LinkStatus, status) If status = False Then MsgBox(GL.GetProgramInfoLog(program)) End If For i As Integer = 0 To shaderList.Length - 1 GL.DetachShader(program, shaderList(i)) Next Return program End Function

  Read the article

• Converting raw data type to enumerated type

  - by Jim Lahman

  There are times when an enumerated type is preferred over using the raw data type.  An example of using a scheme is when we need to check the health of x-ray gauges in use on a production line.  Rather than using a scheme like 0, 1 and 2, we can use an enumerated type: 1: /// <summary> 2: /// POR Healthy status indicator 3: /// </summary> 4: /// <remarks>The healthy status is for each POR x-ray gauge; each has its own status.</remarks> 5: [Flags] 6: public enum POR_HEALTH : short 7: { 8: /// <summary> 9: /// POR1 healthy status indicator 10: /// </summary> 11: POR1 = 0, 12: /// <summary> 13: /// POR2 healthy status indicator 14: /// </summary> 15: POR2 = 1, 16: /// <summary> 17: /// Both POR1 and POR2 healthy status indicator 18: /// </summary> 19: BOTH = 2 20: } By using the [Flags] attribute, we are treating the enumerated type as a bit mask.  We can then use bitwise operations such as AND, OR, NOT etc. . Now, when we want to check the health of a specific gauge, we would rather use the name of the gauge than the numeric identity; it makes for better reading and programming practice. To translate the numeric identity to the enumerated value, we use the Parse method of Enum class: POR_HEALTH GaugeHealth = (POR_HEALTH) Enum.Parse(typeof(POR_HEALTH), XrayMsg.Gauge_ID.ToString()); The Parse method creates an instance of the enumerated type.  Now, we can use the name of the gauge rather than the numeric identity: 1: if (GaugeHealth == POR_HEALTH.POR1 || GaugeHealth == POR_HEALTH.BOTH) 2: { 3: XrayHealthyTag.Name = Properties.Settings.Default.POR1XRayHealthyTag; 4: } 5: else if (GaugeHealth == POR_HEALTH.POR2) 6: { 7: XrayHealthyTag.Name = Properties.Settings.Default.POR2XRayHealthyTag; 8: }

  Read the article

• User "oracle" unable to start or stop listeners

  - by user12620111

  Recently ran into a problem where user "oracle" was unable to start or stop listeners: oracle$ srvctl stop listener PRCR-1065 : Failed to stop resource ora.LISTENER.lsnr CRS-0245:  User doesn't have enough privilege to perform the operation CRS-0245:  User doesn't have enough privilege to perform the operation PRCR-1065 : Failed to stop resource ora.LISTENER_IB.lsnr CRS-0245:  User doesn't have enough privilege to perform the operation CRS-0245:  User doesn't have enough privilege to perform the operation The system is currently "fixed":oracle$ srvctl start listeneroracle$ srvctl status listenerListener LISTENER is enabledListener LISTENER is running on node(s): etc9cn02,etc9cn01Listener LISTENER_IB is enabledListener LISTENER_IB is running on node(s): etc9cn02,etc9cn01oracle$ srvctl stop listeneroracle$ srvctl status listenerListener LISTENER is enabledListener LISTENER is not runningListener LISTENER_IB is enabledListener LISTENER_IB is not runningoracle$ srvctl start listenerHow it was "fixed":Before:# crsctl status resource ora.LISTENER.lsnr -p | grep ACL=ACL=owner:root:rwx,pgrp:root:r-x,other::r--# crsctl status resource ora.LISTENER_IB.lsnr -p | grep ACL=ACL=owner:root:rwx,pgrp:root:r-x,other::r--"Fix":# crsctl setperm resource ora.LISTENER.lsnr -o oracle# crsctl setperm resource ora.LISTENER.lsnr -g oinstall# crsctl setperm resource ora.LISTENER_IB.lsnr -g oinstall# crsctl setperm resource ora.LISTENER_IB.lsnr -o oracleAfter:# crsctl status resource ora.LISTENER.lsnr -p | grep ACL=ACL=owner:oracle:rwx,pgrp:oinstall:r-x,other::r--# crsctl status resource ora.LISTENER_IB.lsnr -p | grep ACL=ACL=owner:oracle:rwx,pgrp:oinstall:r-x,other::r--I may never know how the system got into this state.

  Read the article

• How to fix "Sub-process /usr/bin/dpkg returned an error code (1)" when installing and upgrading packages?

  - by soum

  I am getting this error whenever tring to install or update anything: "Sub-process /usr/bin/dpkg returned an error code (1)" I need help, as I cannot install or upgrade any packages on my Ubuntu 11.10 system. Here is the rest of the error: unknown argument `triggered' dpkg: error processing mtools (--configure): subprocess installed post-installation script returned error exit status 1 Processing triggers for network-manager-pptp-gnome ... No apport report written because MaxReports is reached already postinst called with unknown argument `triggered' dpkg: error processing network-manager-pptp-gnome (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Processing triggers for network-manager-pptp ... postinst called with unknown argument `triggered' dpkg: error processing network-manager-pptp (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Processing triggers for network-manager-gnome ... /var/lib/dpkg/info/network-manager-gnome.postinst called with unknown argument `triggered' dpkg: error processing network-manager-gnome (--configure): subprocess installed post-installation script returned error exit status 1 Processing triggers for network-manager ... No apport report written because MaxReports is reached already /var/lib/dpkg/info/network-manager.postinst called with unknown argument `triggered' dpkg: error processing network-manager (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Processing triggers for mscompress ... postinst called with unknown argument `triggered' dpkg: error processing mscompress (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Errors were encountered while processing: netbase mtr-tiny module-init-tools mountmanager mono-4.0-gac mousetweaks mozilla-plugin-vlc mtools network-manager-pptp-gnome network-manager-pptp network-manager-gnome network-manager mscompress E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >