Search Results

Search found 4065 results on 163 pages for 'intel mkl'.

Page 112/163 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

• Does dual-channel work only with an even number of RAM sticks?

  - by iconiK

  I have noticed that on the ASUS P5QL Pro motherboard the BIOS says "Dual Channel Asymmetric Mode" during POST. The motherboard has three 2GB Kingston ValueRAM 800 MHz DIMMs populated in the first 3 slots from the CPU socket. I have not run any benchmarks to verify that dual-channel is somehow being used, but I believed that dual-channel has to have an even number of sticks (and for triple channel, a multiple of 3). Another example is the Intel DX58SO motherboard; it has four DIMM slots, yet it's an LGA 1366 motherboard which does triple-channel. Apparently triple-channel still works with four DIMMs, instead of falling back to dual-channel. What does the BIOS' POST message mean in those case? Is dual-channel really used for the first two DIMMs, with the other one being an odd one in single-channel mode?

  Read the article

• Creating a vm using Hyper-V causes the host of BSOD

  - by Arcass

  Hi, Problem description: When I try to create a virtual machine, the host bsod part way through the process. From the logs in lookes to fail/hang on the "Creating new VirtualDisckDriver with new VHD" step. The BSOD error code is SYSTEM_SERVICE_EXCEPTION : STOP:0x0000003B When the machine has finished restarting, it looks to have created the vhd and XML files for the vm but it isn't accessable. I have two server bothing behaving in exactly the same way, so I don't believe it's a hardware fault. Has anyone had a similar experince? How did you resolve the problem? NOTES Hardware: HP DL380 G6 BIOS : 2010.03.30 (14 Apr 2010) [Latest from HP website] Inter Hyperthreading: Disabled Intel Virtuazation Technology : Enabled No-Execute Memory Protection: Enabled Mem check reports no errors OS: Windows 2008 Sp2 x64bit fully updated regards Arcass

  Read the article

• Capturing a firewire video feed in Leopard on a G4

  - by Justin Dearing

  Hi, I have a powerbook G4 that I loaded up with Leopard (OSX 10.5). I don't have iMovie, since the Leopard version requires an intel mac. I have a Sony Digital 8 Camcorder with firewire and usb output. The usb output requires a special driver on windows. I don't think OSX will support it. I wish to capture the video stream from the camera on my G4. VLC does not support firewire capture on OSX, I don't want to pay for QT professional. I'm looking for a solution. I'd prefer open source, but I'd consider freeware and inexpensive for pay options. On a related note, if it can capture still frames, I have a related question.

  Read the article

• Virtualizing OpenSolaris with physical disks

  - by Fionna Davids

  I currently have a OpenSolaris installation with a ~1Tb RaidZ volume made up of 3 500Gb hard drives. This is on commodity hardware (ASUS NVIDIA based board on Intel Core 2). I'm wondering whether anyone knows if XenServer or Oracle VM can be used to install 2009.06 and get given physical access to the three SATA drives so that I can continue to use the zpool and be able to use the Xen bits for other areas. I'm thinking of installing the JeOS version of OpenSolaris, have it manage just my ZFS volume and some other stuff for work(4GB), then have a Windows(2GB) and Linux(1GB) VM (theres 8Gb RAM on that box) virtualised for testing things. Currently I am using VirtualBox installed on OpenSolaris for the Windows and Linux testing but wondered if the above was a better alternative. Essentially, 3 Disks - OpenSolaris Guest VM, it loads the zpool and offers it to the other VMs via CIFS.

  Read the article

• Why does the EFI shell not detect my Windows DVD?

  - by Oliver Salzburg

  I'm currently looking into (U)EFI for the first time and am already really confused. I insert the Windows Server 2008 R2 Enterprise disc into the DVD-ROM and boot into the EFI shell. The shell will automatically list all detected devices, which are: blk0 :CDRom - Alias (null) Acpi(PNP0A03,0)/Pci(1F|2)/Ata(Primary,Master)/CDROM(Entry0) blk1 :BlockDevice - Alias (null) Acpi(PNP0A03,0)/Pci(1F|2)/Ata(Primary,Master) To my understanding, it should have already detected the filesystem on blk0 and should have mounted it as fs0. Why is that not happening? If I insert a USB drive, it gets mounted just fine. The board is an Intel S5520HC in case that makes a difference.

  Read the article

• Sharing a wifi connection between different user profiles on Windows XP

  - by crowne

  I've set-up two separate user profiles on an old laptop running Windows-XP, and noted the following strange behaviour. When the wireless network is setup using WEP both user profiles can connect to the internet and I can switch between user profiles, without network connectivity issues. However when I changed the wireless security to WPA2, the first user to connect gets access to the internet, when switching to the second profile the connection fails. The behaviour is the same regardless of which of the two profiles logs on first. I also tried this with one user with admin rights and one without, and got the same result. I'm not too concerned about a fix for this other than forcing the users to log-off when sharing the laptop, but I'd be interested to know if anyone can corroborate my findings. The network config was done using Intel® PROSet/Wireless.

  Read the article

• How to Shutdown PC by Pressing Power Button

  - by AgA

  I always Hibernate my PC. Sometimes when I boot, it does not recognize the mouse/keyboard or any USB devices. I've also setup it to go in sleep in 5 minutes. In that case I can't restart the PC so that USB starts working. When I press the Power button then it starts shutdown but asks confirmation twice one is for shutdown by force confirmation and then there is one more. When my USB is disabled I can't input these options. So I switch off the power. What I want is that upon pressing Power Button it should at once start shutdown without asking any more confirmations System details: Win-7 Home Premium 64 bit Intel i3 530 Asus P montherboard EDIT: It is Desktop PC

  Read the article

• SATA drive not recognized when installing RHEL 5.1 on PowerEdge R410

  - by Rachel

  Here's my setup: Dell R410 with Perc S100 (software) raid controller on an Intel ICH10R chipset The first problem is that the Perc S100 is only supported on windows. I'm trying to install RHEL 5.1. It boots from the cdrom, but later the installer can't see the cdrom or hard drive. Both are connected to the on-board sata controller. The only options in the R410 bios for SATA are ATA or RAID. I don't need raid, I just want a single drive setup.

  Read the article

• CentOS default installation gave 60% disk space to tmpfs partition

  - by garconcn

  I installed a CentOS server which will be used for xen hypervisor. The server has two Intel(R) Xeon(R) CPU E5620 and 148G memory. The OS was installed on a 120G SSD drive. After the installation, I found that the tmpfs partition occupied about 60% of the drive. Even though I don't need much space for the OS, will there be any problem with 71G tmp partition? Thanks for any comment. [root@cloud ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 55G 1.1G 51G 3% / /dev/sda1 99M 13M 82M 14% /boot tmpfs 71G 0 71G 0% /dev/shm

  Read the article

• XenServer migrate machines between hosts

  - by Hubert Kario

  I have a XenServer 5.6 Free setup with 5 VMs (Windows and Linux) using about 1.5TB of directly attached storage. Because our virtualisation needs have grown a bit, we currently are preparing a faster XenServer 6.0 Free machine with more RAM and a more storage. Again, directly attached disks. How can I migrate the VMs between XenServer machines? I don't need to keep the machines up and running during migration, but using VM export and import would definitely take too long. Would making a VM with the same configuration on new host and dd'ing the LVM volume over network be the only quick and least painful solution? Are there any "gotchas" I should look out for when doing something like this? The old machine has an AMD Phenom II, the new has Intel Xeon E5 CPUs.

  Read the article

• Choosing A Power Supply [closed]

  - by Geeks On Hugs

  Possible Duplicate: Power Supply Capacity Formula How can I check if my system needs more PSU power? I'm not sure if it's OK or not to ask a hardware question here. If not please let me know a good place but I've always got good info here so I thought I'd give it a shot. I'm custom building a new workstation for coding (Linux/Eclipse). How do I determine how much power the power supply needs? I'm building a mini ITX system on a budget and so I need to get as small as possible that is sufficient. I'll have a mini itx mobo with on board wifi and bluetooth, 8 GB RAM, an Intel i3 3.1 Ghz processor, 64 GB SSD and a slim optical drive. In the future I might add a descrete GPU, 16 GB RAM, 128 GB SSD. What is the minimum power I need and how do I calculate that?

  Read the article

• Time Machine (archive) of pre-Leopard systems?

  - by benc

  I want to get off an older Mac OS X system permanently. It is an iBook G3, so that has two important characteristics: Power PC, not Intel based. Runs only Tiger, not Leopard. This means, as far as I can tell: Cannot run Time Machine directly. Here's the approach I have been contemplating: Mount the drive in Firewire mode. Back up the drive as a external drive to the Time Machine volume. Disconnect the drive (permanently). However, I'm concerned that this drive will eventually age out, when the Time Machine volume fills up, and the old-system-as-external-drive is gone. Would it be better to do a single backup with another utility, to shared disk?

  Read the article

• update ocz vertex le capacity via firmware update

  - by Ben Voigt

  I have an OCZ Vertex LE 100GB drive. It's actually 128GiB of NAND flash, with a whopping 28%+ reserved for write combining. Most 128GiB drives are actually ~ 115GB usable (and marketed as 120GB or 128GB). There were rumors that the reserved fraction could be decreased on OCZ 100GB drives. Can anyone provide a link to firmware that does that, or an official statement that no such firmware exists? (NB: I recently installed the 1.24 firmware from the OCZ site, it didn't affect the capacity. Possibly because the rumors say the capacity change is destructive to existing content.) Of possible interest: flashing firmware was more of a pain than it should have been -- the tool didn't detect the disk until I booted an older Windows install off a secondary hard disk, I suspect the Intel SATA driver is the issue and tool only works with the msachi.sys driver.

  Read the article

• Artefacts during HDV capture

  - by Jakub Konecki

  When I try to capture HDV video stream from a Canon HV20 camera to a Dell Studio 1558 (Intel i7 720qm) laptop running Win 7 Home Premium x64, the image appears with a very annoying noise - it contains block artefacts. Something is wrong with the Fire Wire controller (Ricoh 1304 OHCI host controller, build-in). Tried changing the driver to legacy one to no avail. This does not happen with DV stream. I'm using a Belkin cable. The capture works OK on another machine.

  Read the article

• How many VPS' can I create on my server?

  - by user197692

  I need to create as many VPS's on my dedicated server (KVM or OpenVZ) in order to sell them but I really don't know the answer. RAM calculation is simple, it's more about CPU resources, how many VPS's can hold. I'am talking about Intel i7-2600 (4 cores, 8 Threads). I need to deploy as many VPS's. It's all about the nr threads? i.e. 8 threads = maximum 8 x 1vCPU or maximum 4 x 2vCPU? I'am planning to use 1Gb and 2Gb memory on each VPS, the server has 16Gb (but I can raise RAM if need it. So, can I create 8 KVM VPS's with 4 vCPU and 2Gb ram each ? How about 20 VPS's with 1Gb ram and 4vCPU each? How is this decision affected by the hypervisor (KVM, OpenVZ, VMware)?

  Read the article

• Is a ext3 Linux filesystem byte order independent

  - by Lothar

  I have a good old HP-C3700 Workstation with PA-RISC CPU here that I would like to use as a subversion server for a very large repository. I just worry what happens if the workstation dies (everybody who knows this computer knows that it is running like an Abrams tank and unlikely to happen in the next decade). I'm using Debian Linux on this system. If the mainboard dies can I just plug the SCSI drive into a PC and read the files from a normal Intel Linux PC? Which software RAID levels would be safe?

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the last Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• Gentoo on Mac Mini - can't get framebuffer to work

  - by user42055

  I have the latest Gentoo on an intel mac mini with 945G graphics. I'm trying to start X (with no config) but it complains that /dev/fb0 doesn't exist. I've tried adding the following options to the kernel boot params: video=intelfb:mode=800x600-32@60,accel,hwcursor vga=761 Because I read that the fb might not be enabled unless you set a vga= option. Unfortunately the kernel doesn't recognise that option. If I changed it to vga=ask it presents me a list of about 6 text modes no greater than 80x60. In the kernel I have agpgart, drm (using i830 module) and vga text console compiled in. What am I not doing right ?

  Read the article

• How can I disable DPMS temporarily in X under a modern linux?

  - by wrt

  Historically if you wanted to control blanking and DPMS in X, you could do it with xset. Issuingxset -dpms on my laptop results in xset q returning "DPMS is Disabled", as it should. But my screens still turn off. I'm running an up-to-date Arch Linux using KMS with integrated Intel graphics, I'm not running GNOME or willing to use anything that needs something like it. I am however stuck with DBUS and HAL. I've tried fiddling with the various timeouts, and it hasn't helped - specifically, changing the timeouts seems to be able to turn off the screen sooner, but not stop it from turning off :) This makes me suspect that there's something else overriding the setting. Is there any way to get xset to actually function as it used to, or at least stop lying to me? Note that I don't want to permanently disable DPMS or blanking - just to be able to control it when I need to.

  Read the article

• My KDE very slow in certain operations

  - by Pietro

  I have a problem with my Linux installation. It seems that the KDE code that deals with directory windows is extremely slow (on both Dolphin and Konqueror). This happens both when I click on a directory icon and when I want to open/save a file from many KDE applications. The time the window takes to open can be one minute or more. The same happens when I right click on an icon. Looking at the CPU usage, this is very low (less than 10%). Am I the only one with this problem, or is it well known and maybe already fixed? Consider that I cannot update to a more recent version of OpenSuse. Thank you, Pietro Configuration: Linux version: OpenSuse 11.4 KDE 4.6.0 System: DELL Precision T3500 - Intel Xeon Home directory mounted on a remote drive. <-- could this be the reason?

  Read the article

• HDD situation - what would be best - data and backup

  - by Sam Johnson

  I just installed W8 on an Intel 330 180 GB SSD. I have 3 1TB HDDs. 1 HDD will be external for backup. 2 HDDs are then available for my PC. I do not need 2 TB of storage, so I thought I'd set these up to be exact clones of one another, so that if one dies I have a backup in the computer to go along with my external. Is this a good set up? How best would this be accomplished? I've heard people suggest RAID but I've never done RAID, have no idea what it is, and have no idea how to set it up in my BIOS. Thanks in advance

  Read the article

• Is there a test to see if hardware virtualization (vmx / svm) are presently enabled within a Linux session?

  - by Dr. Edward Morbius

  I'm writing procedures for configuring VirtualBox support for 64-bit SMP guests, which requires hardware virtualization suppot (VTx/Intel, AMD-V/AMD). I have successfully configured this myself, however I'd like the procedure to be clear. sed -ne '/^flags/s/^.*: //p' /proc/cpuinfo | egrep -q '(vmx|svm)' && echo Has hardware virt || echo No HW virt ... shows if the CPU is capable. I've still got to go enable the feature in BIOS. Any way to test from within Linux to see that this is no or not? Thanks. (Edit: s/xvm/svm/ in title)

  Read the article

• Configuration Tuning for PostgreSQL 9.1 PostGIS 1.5 Ubuntu 12.04 Server

  - by Martin

  My server performance is poor. At times SSH, top, and other features or commands are very slow to respond, taking several seconds or more. A query that normally takes 5 minutes can sometimes take 30 minutes. The database is mostly being used to do a spatial query (grid and summarize) on approximately 500GB of stored data spread between 4 tables. Restarting the server works as a temporary fix, but cannot be used as a long term solution. Any suggestions for how to diagnose and solve my performance issues? Hardware and Configuration: 3.3 GHz Intel quad core i5 16 GB DDR3 RAM 6 TB software RAID 10 (6 x 2 TB drives) Ubuntu 12.04 64-bit Postgres 9.1 PostGIS 1.5

  Read the article

• Computer won't start unless power is removed for ~5 minutes

  - by Paul Tarjan

  I have a fairly standard 2-year old desktop computer (quad-core intel, single hard drive, decent video card, 300W power supply) which recently started acting up. I'm not sure what the cause is, so hopefully you can help. Sometimes (once a week-ish) I press the power button and nothing happens. No blinking, no sounds, no nothing. If I remove the power cord (or flip the switch on the power supply) I hear a capacitor discharge. If I leave it in the "no power at all" state for about 5 minutes then I can put the plug back in and the computer works perfectly. What is the issue? What do you think I have to replace?

  Read the article

• Computer won't start unless power is removed for ~5 minutes

  - by Paul Tarjan

  I have a fairly standard 2-year old desktop computer (quad-core intel, single hard drive, decent video card, 300W power supply) which recently started acting up. I'm not sure what the cause is, so hopefully you can help. Sometimes (once a week-ish) I press the power button and nothing happens. No blinking, no sounds, no nothing. If I remove the power cord (or flip the switch on the power supply) I hear a capacitor discharge. If I leave it in the "no power at all" state for about 5 minutes then I can put the plug back in and the computer works perfectly. What is the issue? What do you think I have to replace?

  Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >