Search Results

Search found 5501 results on 221 pages for 'receive'.

Page 112/221 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

  • HP DV6 connects but no internet

    - by Frank Barcenas
    I have a Hewlett Packard DV6. I connected to the access point. I receive an IP address/default gateway/DNS,etc(DHCP). I cannot ping my gateway. DNS lookups fails. There is just no connectivity. My driver is listed as being IWLWIFI. An lspci shows my card to be a Realtek RTL8101E/RTL8102E. I can't ping myself from another computer. eth0 Link encap:Ethernet HWaddr c8:0a:a9:0c:a7:45 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:41 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:561 errors:0 dropped:0 overruns:0 frame:0 TX packets:561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42164 (42.1 KB) TX bytes:42164 (42.1 KB) wlan0 Link encap:Ethernet HWaddr 00:26:c7:04:97:c0 inet addr:192.168.1.109 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:c7ff:fe04:97c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2035 (2.0 KB) TX bytes:12371 (12.3 KB)

    Read the article

  • Totem crashes immediately after startup in 12.10

    - by Sakib Hasan
    I did a fresh install of Ubuntu 12.10 and did sudo apt-get update && sudo apt-get update. Then I installed ubuntu-restricted-extras, audacious and vlc from Software Center. After that I tried launch Totem Movie player but in terminal following error comes up: (totem:9295): Gdk-ERROR **: The program 'totem' received an X Window System error. This probably reflects a bug in the program. The error was 'BadDrawable (invalid Pixmap or Window parameter)'. (Details: serial 1808 error_code 9 request_code 152 minor_code 9) (Note to programmers: normally, X errors are reported asynchronously; that is, you will receive the error a while after causing it. To debug your program, run it with the GDK_SYNCHRONIZE environment variable to change this behavior. You can then get a meaningful backtrace from your debugger if you break on the gdk_x_error() function.) Trace/breakpoint trap (core dumped) I tried purge and again install. But the error remains. What should I do?

    Read the article

  • How can we best petition to bring Adobe creative software to Ubuntu?

    - by Sixthlaw
    Now I know its not as simple as asking for Adobe to support their design software on Ubuntu, but is there a way for the community and Canonical to make known to Adobe the rapidly growing amount of Linux users, and their desire for this great set of tools OFFICIALLY? I know that many of the answers I receive might be of the fashion "Its not going to happen", "use the free tools provided" or "Who knows it might happen in the near future", but this IS not what I am looking for. I have noticed, on sites like www.OmgUbuntu.com, there are links to pages where people can "like" the idea. Is there a way to try and get the whole community on board with this one, even Canonical, and as stated above, put forward this proposal to Adobe. The current requests for an Adobe CS, for Linux, are in dribs and drabs scattered all of the internet. Now is the best time to come up with productive solutions on how we can best gather statistics on the amount of people willing to buy the Adobe CS. These are the words of an Adobe employee: "I have forwarded this feedback on to the appropriate team who will consider it for future releases of Adobe software." The larger amount of people we have unified in the ONE community proposal, the greater chance we have of getting the software. How can we make this happen?

    Read the article

  • Problems after installing a plethora of updates

    - by box
    yesterday I decided to install 32-bit Ubuntu on my 64-bit desktop, first of all, is that a problem? After installing, i had around 270 updates to install, according to the update manager. I was having trouble launching a game with WINE, so I thought updating might help. After updating, I restarted my computer, and after a long while it showed me my desktop and the icon's on it, but I didn't get anything else. I didn't have the "taskbar" (not sure what it's called, sue me) on the left side, nor the bar at the top. I also received an error message saying some program had stopped working. I decided to restart my computer again, and that was when it told me that i have to re-configure my drivers, or run in "Low Graphics" mode for one session, amongst other options. Well, I decided to try to revert to the "basic video drivers", which was an option it gave. Restarting the computer gave me the same problem as in the second paragraph. After a few more restarts and a night of restless sleep, here I am trying to start my computer again, only to receive a black screen, and my monitor "going to sleep". I'm sort of stumped here, being new to Ubuntu (desktop, at least) and I really hope this gets fixed without me having to install Ubuntu on yet another partition (I have three other partitions for various things already) tl;dr: Black screen on boot after installing updates.

    Read the article

  • Which iPhone ad API has produced the highest revenue for you?

    - by Kyle Humfeld
    This isn't a technical question, but more of a request for advice and empirical/anecdotal data. I'm nearly done writing a free app for iPhone, and I'm at the stage where I'm going to put ads into the app. I've had mixed success in the past with iAd (their fill rates have been atrocious recently, and their payouts have cut by about 75% over the past 4 months or so), and would like to know how much ad revenue you, the community, has seen from the various ad APIs you've used for your iPhone apps. This isn't a request for opinion, i.e. which is 'better', only what kinds of numbers you're seeing. I don't need absolute figures, but 'iAd pays x% higher than AdMob, and y% lower than AdSense' would be extremely helpful to me as I make my decision as to which ad API to integrate into my App. Also, have you had any experience or success with integrating multiple ad APIs into the same app? That's something I'm considering doing in my current iAd-filled apps (particularly my iPad app, which has yet to receive a single impression after nearly 60,000 requests)... something like: 1) Request-from-iAd 2) if that fails, request-from-adSense 3) if that fails, request-from-adMob 4) if that fails, ... etc.

    Read the article

  • Should one use a separate database for application data and user data?

    - by trycatch
    I’ve been working on a project for a little while and I’m unsure which is the better architecture. I’m interested in the consensus. The answer to me seems fairly obvious but something about it is digging at me and I can't pick out what. The TL;DR is: how do you handle a program with application data and user data in the same DB which needs to be able to receive updates to the application data periodically? One database for user data and one for application, or both in one? The detailed version is.. if an application has a database which needs to maintain application data AND user data, and the user data all references application data, it feels more natural to me to store them in the same database. But if there exists a need to be able to update the application data within this database periodically, should this be stripped into two databases so that one can simply download the updated application data database file as an update and replace the old one? Or should they remain as one database, and the application data be updated via a script which inserts the new data into the existing database? The second sounds clearly preferable to me... but for some reason just doesn’t feel right, and I can't pick out quite why.

    Read the article

  • How to perform game object smoothing in multiplayer games

    - by spaceOwl
    We're developing an infrastructure to support multiplayer games for our game engine. In simple terms, each client (player) engine sends some pieces of data regarding the relevant game objects at a given time interval. On the receiving end, we step the incoming data to current time (to compensate for latency), followed by a smoothing step (which is the subject of this question). I was wondering how smoothing should be performed ? Currently the algorithm is similar to this: Receive incoming state for an object (position, velocity, acceleration, rotation, custom data like visual properties, etc). Calculate a diff between local object position and the position we have after previous prediction steps. If diff doesn't exceed some threshold value, start a smoothing step: Mark the object's CURRENT POSITION and the TARGET POSITION. Linear interpolate between these values for 0.3 seconds. I wonder if this scheme is any good, or if there is any other common implementation or algorithm that should be used? (For example - should i only smooth out the position? or other values, such as speed, etc) any help will be appreciated.

    Read the article

  • The Real Value Of Certification

    - by Brandye Barrington
    I read a quote recently by Rich Hein of CIO.com "Certifications are, like most things in life: The more you put into them, the more you will get out." This is what we tell candidates all the time. The real value in obtaining a certification is the time spent preparing for the exam. All the hours spent reading books, practicing in hands-on environments, asking questions and searching for answers is valuable. It's valuable preparation for the exam, but it's also valuable preparation for your future job role and for your career. If your goal is just to pass an exam, you've missed a very important part of the value of certification.We receive so many questions through different forms of social media on whether or not certification will help candidates get jobs or get better jobs. Surveys conducted by us and by independent entities all point to the job and salary benefits of certification. However, a key part of that equation is whether a candidate can actually perform successfully in a job role. If preparation time was used to practice and learn and master new skills rather than to memorize a brain dump, the candidate will probably perform successfully in their job role, and job opportunities and higher salary will likely follow. Candidates who do not show that initiative, will not likely reap the full benefits of certification.Keep this in mind as you approach your next certification exam. You are preparing for a career, not an exam. This may help you to be more appreciative of the long hours spent studying!

    Read the article

  • How to develop a Windows 8 app in 30 days!

    - by Scott Spradlin
    Begin your 30-day journey to create a Windows Store style app. Sign up to get started and receive: Insider tips and tricks on Windows 8 application development. Personal on-the-phone access to a Windows 8 architect*. An exclusive one-on-one Windows Store design consultation*. An opportunity to get expert help from a Microsoft Services Engineer at an App Excellence Lab. Sign up today and get started. Your new Windows 8 app could be mere days away. * Offer good only to legal residents in the 50 United States & D.C., age 18 or older to hobbyists, professionals or developers in the field of software tech who sign up for building a Windows 8 application on www.generationapp.com. Offer limited to 250 design consultations per month and 500 technical review consultations per month, on a first come first served basis. Limit of one session of each offer type per person. This offer is non-transferable and cannot be combined with any other offer. This offer ends when supplies are exhausted, and is not redeemable for cash.

    Read the article

  • handling multiple interviews / offers [closed]

    - by farble1670
    What's the best way to handle a situation where you have, or expect to have multiple offers? The ideal situation is that your several offers come in about the same time, and you make a choice. this is not how it happens though. You may have an offer, and several near-final interviews lined up for the following days or weeks. One way to handle it would be to ask for a longer time to decide on the first offers you receive. 2 weeks? This gives time to rush the rest of the things you have going through to an end. i question whether asking for 2 weeks to decide is reasonable though. My guess is that an employer would see through that and force your hand. Another way to handle it would be to accept the first offer, and ask for a reasonable period before your start date, then simply "quit" the first position before you ever start if something better comes along. On one hand, employment is at-will, and employers exercise this fact regularly. On the other hand, it seems morally the wrong thing, and has the potential to burn some bridges. And of course the last option is to simply evaluate each offer in isolation, and accept or reject within the given time frame. any thoughts?

    Read the article

  • Laptop power button not working

    - by DyP
    I have a (seemingly rather exotic) Dell Latitude XT2 notebook running Lubuntu 12.04, fresh install. Tried to get the power button to work as expected (opening lubuntu-logout, just as I think it was meant to be out-of-the box), but no success: power button does nothing but forced power-off on long press. Here some more information, please ask if something more could help: Power button is recognized as a device: xinput lists Power Button as a slave keyboard at /dev/input/event1, and I can run a tool to listen to that device and invoke some action (successfully). But using .config/openbox/lubuntu-rc.xml to assign some action to XF86ShutDown or XF86PowerOff does nothing. Works well for any key of the keyboard. xinput --test reports a keycode (key press, key release) of 124 when pressing & releasing the power button. xmodmap -pk lists 124 mapped to XF86PowerOff which seems correct to me (btw: is this the same as XF86ShutDown?) When assigning another keysymname to the 124 keycode, e.g. 'w', still nothing happens when pressing the power button (no window seems to receive a 'w'). Works well for any key on the keyboard. The outputs of xev for a press/release of the power button irritate me: MappingNotify event, serial 41, synthetic NO, window 0x0, request MappingKeyboard, first_keycode 8, count 248 FocusOut event, serial 41, synthetic NO, window 0x2a00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 41, synthetic NO, window 0x2a00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 41, synthetic NO, window 0x0, keys: 93 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 (instead of 93, I also get different values) I might have missed something very basic since I'm not very familiar with both openbox/lubuntu and the X input system. Btw.: same goes for three other special buttons on my laptop..

    Read the article

  • Integrating Amazon EC2 in Java via NetBeans IDE

    - by Geertjan
    Next, having looked at Amazon Associates services and Amazon S3, let's take a look at Amazon EC2, the elastic compute cloud which provides remote computing services. I started by launching an instance of Ubuntu Server 14.04 on Amazon EC2, which looks a bit like this in the on-line AWS Management Console, though I whitened out most of the details: Now that I have at least one running instance available on Amazon EC2, it makes sense to use the services that are integrated into NetBeans IDE:  I created a new application with one class, named "AmazonEC2Demo". Then I dragged the "describeInstances" service that you see above, with the mouse, into the class. Then the IDE automatically created all the other files you see below, i.e., 4 Java classes and one properties file: In the properties file, register the access ID and secret keys. These are read by the other generated Java classes. Signing and authentication are done automatically by the code that is generated, i.e., there's nothing generic you need to do and you can immediately begin working on your domain-specific code. Finally, you're now able to rewrite the code in "AmazonEC2Demo" to connect to Amazon EC2 and obtain information about your running instance: public class AmazonEC2Demo { public static void main(String[] args) { String instanceId1 = "i-something"; RestResponse result; try { result = AmazonEC2Service.describeInstances(instanceId1); System.out.println(result.getDataAsString()); } catch (IOException ex) { Logger.getLogger(AmazonEC2Demo.class.getName()).log(Level.SEVERE, null, ex); } } } From the above, you'll receive a chunk of XML with data about the running instance, it's name, status, dates, etc. In other words, you're now ready to integrate Amazon EC2 features directly into the applications you're writing, without very much work to get started. Within about 5 minutes, you're working on your business logic, rather than on the generic code that anyone needs when integrating with Amazon EC2.

    Read the article

  • Incomplete Ubuntu 12.04 install dual-boot XP

    - by Mike
    This weekend has been the 1st time I've tried to install Ubuntu. On the initial install, (I am using a USB) the installation went all the way through and asked to restart when completed. I was not able to get grub to boot and kept going through Windows. After some research I found some articles on updating/reinstalling grub, so I followed those. I finally got grub to load after a day but there was no Windows option only the Ubuntu 12.04 which when I selected it only gave me a fatal error 17. I booted from the USB again and deleted the partitions and installed again. This time I got an error 15. I then booted through XP and downloaded the WUBI.exe and uninstalled Ubuntu and reinstalled again. The installation went to the very end and then gave an error message (which I don't remember exactly what it said) something along the lines of checking my logs on my C drive. I then uninstalled Ubuntu and removed the wubi.exe file and wiped my USB and did the download to the USB again. Booted through USB and ran the install process again. It again went through the install process but after creating username and password and hitting continue, the installation dialogue box disappears and the mouse spinning wheel is displayed, but I do not receive the prompt to restart. I can still access the side menu for Ubuntu but the wheel keeps spinning. How do I get Ubuntu to install properly?

    Read the article

  • My work isn't being used... what can/ should I do?

    - by Matt
    Several months ago I was approached by a small business, who had seen my work previously and asked me to create a website for them. Since then, the website hasn't changed one bit and I haven't heard a word from them. This sucks for them as they paid for a website and haven't used it. It''s frustrating for me because I spent a huge amount of time on the website and feel that all of that effort has been wasted, furthermore, I don't feel I can use the website on my portfolio/ CV. I was thinking of offering to go round to their office for one day, and update the website for them then and there; but I'd need their support whilst there (to get the content for the about page, to get information for on their products etc.) and I don't want to disrupt their work day, nor do I want to sit there like a spare tyre and get nowhere. Furthermore, if I were to do this, should I expect to receive money for it? It's a day of my life, but I'm doing it for my benefit rather than theirs (but they benefit as well). Has anyone else had experience of a client not using their product; how did you handle it? Additional background for those who want it: The company is a local travel agent, and the website lets them CRUD offers and locations, and has several other static pages (about, contact, etc.) At the time of creating the website, I filled the static pages with lipsum, and the offers and locations with fake information, so that I could give the business an idea about what the final pages would look like; during the hand over, I guided them through the CRUD forms (they made notes) and said if they sent me the text for the pages, I'd update it.

    Read the article

  • Configuring an Engenius 3500

    - by dsiddens
    The title speaks to only half of the issue: the other half are the settings in Ubuntu and the sequences therein. The computer in this issue does receive internet with the external antenna jack at the back being fed with a simple magnetic base antenna designed for putting on the roof of an automobile. However, that signal is weak and the Engenius with an external antenna (Rootenna ~15db gain) and ehternet wire will supply a stronger, faster signal. I've set the Engenius to the desired source and entered the correct WEP password. The lights on the Engenius indicate that it's connected to the access point. At the Ubuntu side of this I've worked to no avail changing settings with "Edit Connections" to the point I'm Ask(ing)Ubuntu for help. I have and have RTFM for Engenius 3500 There is an embarrassing side note to this issue: At one time I had the Engenius working! It seems that I can't recall the settings and sequences I used way back when. And I may as well confess to not knowing the Command Line. I'm a GUI guy. Thank you for your time, Doug

    Read the article

  • Booting off a ZFS root in 14.04

    - by RJVB
    I've been running a Debian derivative (LMDE) on a ZFS root for half a year now. It was created by cloning a regular ext4-based install with all the necessary packages onto a ZFS pool, chrooting into that pool and recreating a grub menu and bootloader. The system uses an ext-3 dedicated /boot partition. I would like to do the same with Ubuntu 14.04, but have encountered several obstacles. There is no Trusty zfs-grub package The default grub package doesn't have ZFS support built in. I found a small bug in the build system responsible for that (report with patch created) and built my own grub packages. The built-in ZFS support is dysfunctional, it does not add the proper arguments to the kernel command line I thus installed the ZoL grub package I also use on my LMDE system, which does give me a correct grub.cfg However, even with that correct grub.cfg, the boot process apparently doesn't retrieve the bootfs parameter from the ZFS pool; instead the variable that's supposed to receive the value remains empty. As a result, initrd tries to load the default pool ("rpool"), which fails of course. I can however import the pool by hand, and complete the process by hand. If memory serves me well, I also had to disable apparmor, to avoid the boot process from blocking after importing the pool. Am I overlooking something? Just for comparison, I installed the Ubuntu 3.13 kernel on my LMDE system, and that works just fine (i.e. the identical kernel and grub binaries allow successful booting without glitches on LMDE but not on Ubuntu).

    Read the article

  • Most efficient Implementation a Tree in C++

    - by Topo
    I need to write a tree where each element may have any number of child elements, and because of this each branch of the tree may have any length. The tree is only going to receive elements at first and then it is going to use exclusively for iterating though it's branches in no specific order. The tree will have several million elements and must be fast but also memory efficient. My plan makes a node class to store the elements and the pointers to its children. When the tree is fully constructed, it would be transformed it to an array or something faster and if possible, loaded to the processor's cache. Construction and the search on the tree are two different problems. Can I focus on how to solve each problem on the best way individually? The construction of has to be as fast as possible but it can use memory as it pleases. Then the transformation into a format that give us speed when iterating the tree's branches. This should preferably be an array to avoid going back and forth from RAM to cache in each element of the tree. So the real question is which is the structure to implement a tree to maximize insert speed, how can I transform it to a structure that gives me the best speed and memory?

    Read the article

  • Would having an undergraduate certificate in Computer Science help me get employed as a computer programmer? [on hold]

    - by JDneverSleeps
    I am wondering how would employers perceive the Universtiy Certificate in Computing and Information Systems offered by Athabasca University (a distance education institution... The university is legit and accredited by the Government of Alberta, Canada). I already have a BSc in Statistics from University of Alberta (a classic brick and mortar public university in Alberta, Canada)...so I can state in my resume that I have a "university degree"..... Luckily, I was able to secure a very good employment in my field after the graduation from the U of A. The main reason why I am interested in taking the certificate program through Athabasca is because knowing how to program can increase the chance for promotion in my current job. I also believe that if something turns out bad in my current job and if I ever need to look for a new place to work, having the certificate in computer science will help me get employed as a computer programmer (i.e. my choice for the new job wouldn't be restricted to the field of Statistics). Athabasca University is claiming that the certificate program is meant to be equivalent to the undergraduate minor in computing science. I carefully looked at the certificate's curriculum and as far as I am concerned, the certificate program does have the same level of rigour as the undergraduate minor in Computer Science programs offered by other Canadian universities. I am also confident that the certificate program will get me to pick up enough skills/background to start a career as a computer programmer. The reasons why I am not 100% sure on getting the certificate is worth the tuition are: Athabasca University is a distance education institution (accredited by government but still) The credential that I will receive is "university certificate", not a "undergraduate degree" Do you think it's a good idea for me to pursue the certificate, given the two facts above? again, I already have my Bachelor's degree - although it is not in CS Thanks,

    Read the article

  • How to fix GRUB on dualboot with Windows7 and Ubuntu?

    - by b_oliv
    I am a relatively recent user of Linux. I had several releases of Ubuntu installed on my laptop working in dual-boot and never had any issues. Recently, I installed openSUSE because I thought it would be necessary for an assignment at my university. It turns out it wasn't so I returned to Ubuntu and decided to burn the new .iso to a CD and install it. The problem is that during installation process I almost for sure messed up with the partitions and now, whenever I tried to load Windows 7, it will tells me that a required device is inaccessible. So, I reinstalled Ubuntu again and now all I get is that I am redirected to the GRUB menu without any warnings. I tried creating a Windows Recovery Disk but it gives me Unexpected I/O error. I suspect it is because it was downloaded from the Internet and maybe some files weren't there. I tried everything without success, so I decided to ask here, in the hope I can receive some help and also learn how to help others with it in the future. Here it is my boot info summary: http://paste.ubuntu.com/1344990/ Also, I might add, that on the boot-repair advanced options, the box repair Windows boot files is "locked", so I can't check it. EDIT: Apparentely, the box is locked, because, from what I understood after reading the boot-repair information, everything is fine with my windows boot-files... I still need some guidance though

    Read the article

  • USB ports not working on Xubuntu 12.04 LTS

    - by Zchpyvr
    Basically, my USB ports on my IBM Thinkpad T43 have stopped working most of the time. Sometimes, they mount and appear in Nautilus, but other times, they aren't recognized. The timeline of events on this laptop for the past few months: Started having problems after using a USB port hub. The port would sometimes work but would be fixed with the occasional reboot. Re-partitioned/Expanded my Xubuntu partition (I have a Windows XP/Xubuntu dual boot). Now the majority of the time, the USB fails to recognize devices. In addition, the few times they are recognized, the device may suddenly disconnect. Things I've noticed: The devices still receive power from my computer (I can charge my ipod..etc..) I can't understand dmesg outputs. I don't know if lsusb is telling me anything useful. My dmesg output is here: http://pastebin.com/KdNxHcFC Things start to get weird at the bottom of the file. And my lsusb is: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

    Read the article

  • Handling commands or events that wait for an action to be completed afterwards

    - by virulent
    Say you have two events: Action1 and Action2. When you receive Action1, you want to store some arbitrary data to be used the next time Action2 rolls around. Optimally, Action1 is normally a command however it can also be other events. The idea is still the same. The current way I am implementing this is by storing state and then simply checking when Action2 is called if that specific state is there. This is obviously a bit messy and leads to a lot of redundant code. Here is an example of how I am doing that, in pseudocode form (and broken down quite a bit, obviously): void onAction1(event) { Player = event.getPlayer() Player.addState("my_action_to_do") } void onAction2(event) { Player = event.getPlayer() if not Player.hasState("my_action_to_do") { return } // Do something } When doing this for a lot of other actions it gets somewhat ugly and I wanted to know if there is something I can do to improve upon it. I was thinking of something like this, which wouldn't require passing data around, but is this also not the right direction? void onAction1(event) { Player = event.getPlayer() Player.onAction2(new Runnable() { public void run() { // Do something } }) } If one wanted to take it even further, could you not simply do this? void onPlayerEnter(event) { // When they join the server Player = event.getPlayer() Player.onAction1(new Runnable() { public void run() { // Now wait for action 2 Player.onAction2(new Runnable() { // Do something }) } }, true) // TRUE would be to repeat the event, // not remove it after it is called. } Any input would be wonderful.

    Read the article

  • Rectangular Raycasting?

    - by igrad
    If you've ever played The Swapper, you'll have a good idea of what I'm asking about. I need to check for, and isolate, areas of a rectangle that may intersect with either a circle or another rectangle. These selected areas will receive special properties, and the areas will be non-static, since the intersecting shapes themselves will also be dynamic. My first thought was to use raycasting detection, though I've only seen that in use with circles, or even ellipses. I'm curious if there's a method of using raycasting with a more rectangular approach, or if there's a totally different method already in use to accomplish this task. I would like something more exact than checking in large chunks, and since I'm using SDL2 with a logical renderer size of 1920x1080, checking if each pixel is intersecting is out of the question, as it would slow things down past a playable speed. I already have a multi-shape collision function-template in place, and I could use that, though it only checks if sides or corners are intersecting; it does not compute the overlapping area, or even find the circle's secant line, though I can't imagine it would be overly complex to implement. TL;DR: I need to find and isolate areas of a rectangle that may intersect with a circle or another rectangle without checking every single pixel on-screen.

    Read the article

  • How come there is still so much programming work?

    - by jd_505
    First I'd like to say that I am not pretty sure that this question will meet the guidelines. I think it can goes under the "Freelancing and business concerns" bullet, but I am not sure. Anyway, I will give it a shot. I wonder how the programming jobs hasn't yet "dried" because of the software evolution, for example, I am a developer myself, which means that I do care about software (I mean I am not of the type of guys that needs a computer mainly to just browse the Internet), and still I wouldn't mind if I never receive any more updates on my Ubuntu machine. I find that it provides everything I need, and while the updates provide various bug fixes/improvements, I wouldn't mind using it with it's current state for the rest of my life, for 2 years of Ubuntu usage I have never bumped at a serious bug/problem. Another example is Windows, almost half of it's users still use XP, which is practically ancient, yet they find it satisfying all their needs (and I agreee with them). I could go with many more examples, but by now you are understanding my point and my question. While new "trends" appears all of the time (like a new mobile OS) which runs on new platforms and requires some fresh development work, still the majority of the software effort goes in to what I consider as "completed projects", or at least a state of a project which is enough to be considered as completed. Do you have an explanation ? I can't think of the right tags for this question, please edit it the way you find it to be most appropriate. Thanks.

    Read the article

  • Java vs. C# - Productivity perspective

    - by Edin Dazdarevic
    If you have a number of years experience in working with JAVA and a number of years experience in working with C# and .NET, I would value your opinion on software development productivity differences between these two environments. One of our customers is considering to technically replace their existing software solution. As the replacement will require approx. 10 - 15 man years work, a choice for JAVA or .NET, based on productivity differences between the them, may significantly influence the investment required and time-to-market. Would you be able to provide us, based on your honest and expert opinion, an indication of software development productivity differences between JAVA and C#/.NET? I would prefer to receive an answer as follows: My experience is based on X years experience working with JAVA and X years experience working with C#/.NET. JAVA is X% more productive then C#.NET or C#/.NET is X% more productive than JAVA if you take the the following into account . . . . . . . Thanks

    Read the article

  • How to leverage the internal HTTP endpoint available on Azure web roles?

    - by adelsors
    Imagine you have a Web application using an in-memory collection that changes occasionally, loading it from storage on the Application_Start global.asax event and updating it whenever it changes. If you want to deploy this application on Azure you need to keep in mind that more than one instance of the application can be running at any time and therefore you need to provide some mechanism to keep all instances informed with the latest changes. Because that the communication through internal endpoints between Azure role instances is at no cost, a good solution can be maintaining the information on Azure Storage Tables, reading its contents on the Application_Start event and populating its changes to all instances using the internal HTTP port available on Azure Web Roles. You need to follow these steps to leverage the internal HTTP endpoint available on Azure web roles: 1.   Define an internal HTTP endpoint in the Web Role properties, for example InternalHttpEndpoint   2.   Add a new WCF service to the Web Role, for example NotificationServices.svc 3.   Add a method on the new service to receive notifications from other role instances. 4.   Declare a class that inherits from System.ServiceModel.Activation.ServiceHostFactory and override the method CreateServiceHost to host the internal endpoint.   Note that you can use SecurityMode.None because the internal endpoint is private to the instances of the service, this is provided by the platform. 5.   Edit the markup of the service right clicking the svc file and selecting "View markup" to add the new factory as the factory to be used to create the service    6. Now you can notify changes to other instances using this code:

    Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >